No.9 All Nation Shop 1

Download as pdf or txt
Download as pdf or txt
You are on page 1of 1

STANDARD NOTES:

• DESIGNS AND INFORMATION


CONTAINED ON THIS DRAWING
IS THE COPYRIGHT OF ZC.
• ALL WORK TO BE CARRIED OUT
IN STRICT ACCORDANCE WITH
THE LATEST VERSION OF SANS
10400.
• THE APPROVAL OF THIS
DRAWING DOES NOT RELIEVE
THE CONTRACTOR OF HIS
RESPONSIBILITIES IN RESPECT
OF QUALITY.
• ALL RELEVANT DETAILS AND
DIMENSIONS TO BE CHECKED
BEFORE WORK COMMENCES.
ANY OMISSIONS OR
DISCREPANCIES TO BE
GENERAL NOTES AND SPECIFICATION: REPORTED TO THE ARCHITECT
1. ALL DIMENSIONS AND LEVELS MUST BE CHECKED ON SITE. ANY DISCREPANCIES ON AND ENGINEER.
THE DRAWINGS MUST BE BROUGHT TO THE ATTENTION OF THE ENGINEER TO DRAINAGE NOTES: • THE ARCHITECT AND ENGINEER
RECTIFY.
2. THE CONSTRUCTION OF ALL CONCRETE WORK MUST COMPLY WITH THE • ALL PLUMBING AND DRAINAGE WORK AND ACCEPTS NO RESPONSIBILITY
REQUIREMENTS OF SANS 2001:2007 PART CC1: CONCRETE WORKS (STRUCTURAL) INSTALLATION WORK SANITARY FITTINGS TO 6770 FOR ERRORS RESULTING FROM
6770 AND PART CC2: CONCRETE WORKS (MINOR WORKS). COMPLY WITH THE RELEVANT LOCAL AUTHORITY THE MISINTERPRETATION OF
3. THE CONSTRUCTION OF ALL MASONRY WORK MUST COMPLY WITH SANS 2001- BY-LAWS, REGULATIONS AND REQUIREMENTS.
CM1:2007 MASONRY WALLING. • ALL DRAIN PIPES: MINIMUM FALL 1:60, MAXIMUM
230 6310 230 THE DRAWING.
230 1940 230 4140 230 4. THE CONSTRUCTION OF ALL STRUCTURAL STEELWORK MUST COMPLY WITH SANS FALL 1:10. • ALL WORK TO COMPLY WITH
2001-CS:2005 STRUCTURAL STEELWORK. • ALL WASTE PIPES AND SOIL PIPES TO BE FULLY
5. THE SIZE, POSITION AND LEVEL OF ALL OPENINGS FOR PIPEWORK TO BE CAST-IN ACCESSIBLE ALONG ENTIRE LENGTH OF THE PIPE.
LOCAL MUNICIPAL BY-LAWS.
• ALL DRAWINGS SHALL BE READ
230

AND PUMP PLINTHS SHOWN ON THE CIVIL AND STRUCTURAL DRAWINGS ARE • I.E. TO BE PROVIDED AT EVERY BEND, JUNCTION
PROVISIONAL AND MUST BE CONFIRMED AND APPROVED BY THE MECHANICAL AND CHANGE IN DIRECTION AND EVERY 24 wc IN CONJUNCTION WITH THE
SUPPLIER IN WRITING BEFORE CONSTRUCTION COMMENCES. METERS WITH MARKED COVERS AT GROUND
6. CONCRETE CLASSES (UNLESS OTHERWISE SPECIFIED IN THE PROJECT LEVEL. SPECIFICATIONS.
SPECIFICATIONS) • ALL WASTE PIPE FITTINGS TO HAVE APPROVED
2020

1790

1. STRUCTURAL CONCRETE: CLASS 35/19 (35 MPa) RESEAL TRAPS.


2. BENCHING: CLASS 20/19 (20 MPa) • VENT PIPE OUTLET TO BE MIN. 2m ABOVE ANY

Shower
OPENING.

Shower
3. BLINDING: CLASS 15/19 (15 MPa)
7. CONCRETE COVER TO REINFORCEMENT SHALL BE 50mm UNLESS OTHERWISE • ALL BATH ENCLOSURES TO HAVE ACCESS
SHOWN OR SPECIFIED. PANELS.
8. ALL EXPOSED CONCRETE CORNERS SHALL HAVE A 25mm CHAMFER UNLESS • GULLEYS TO BE TRAPPED AND WITH SUITABLE
230

230

230
ELD
OTHERWISE INDICATED OR SPECIFIED. GULLY GRATING AND TO BE 150 mm ABOVE
9. THE POSITIONS OF CONSTRUCTION JOINTS SHALL BE AS SHOWN ON THE SURROUNDING LEVELS.
DRAWINGS, OR AS AGREED UPON BETWEEN THE ENGINEER AND THE • ALL DRAINS UNDER BUILDINGS OR FOOTINGS TO
CONTRACTOR BEFORE CONSTRUCTION COMMENCES. NO DEVIATION FROM THE BE ENCASED IN 150mm CONCRETE ALL ROUND
CONSTRUCTION JOINT POSITIONS SHOWN ON THE DRAWINGS SHALL BE THE PIPE. LEGEND
PERMITTED WITHOUT THE WRITTEN APPROVAL OF THE ENGINEER. • WASTE PIPES IN FLOORS TO BE SLEEVED AND BE
10. STEEL FORMWORK/SHUTTERING SHALL BE USED IN THE CONSTRUCTION OF ALL FITTED WITH EASILY ACCESSIBLE C.E. ABOVE
LIQUID RETAINING STRUCTURES UNLESS OTHERWISE APPROVED IN WRITING BY FLOOR LEVEL AND EACH END OF SLEEVE. 2HOURS FIRE RATED

3680
THE ENGINEER. • NO DRAIN BENDS OR JUNCTIONS IN OR UNDER PARTITION BOARDS
3450

3450

3450

3450
11. FORMED SURFACE REQUIREMENTS SHALL BE AS SPECIFIED IN THE PROJECT FLOOR SLAB.
SPECIFICATIONS. • KEEP ALL DRAINS 900mm FROM CONCRETE
12. THE DEGREE OF ACCURACY SHALL BE AS SPECIFIED IN THE PROJECT FOUNDATIONS. 110mm FIRE BREAK WALL
SPECIFICATIONS. THE DEGREE OF ACCURACY OF FINISHES SPECIFIED FOR
Existing Door to be FLOATED CONCRETE FINISHES IN PARTICULAR MUST BE STRICTLY COMPLIED WITH. NO ENTRY EXIT
demolished and Cabinet
bricked up
FE FIRE EXTINGUISHER
LEGENDS
220

220

220

220
Polyurethane - Floor Finish
FHR FIRE HOSE REEL
220

Cabinet EXISTING STONCLAD UT IS A DENSE, LIQUID-RICH, SELF-PRIMING, TEXTURED, FOUR-


COMPONENT, NOTCH TROWEL APPLIED, POLYURETHANE MORTAR SYSTEM. FH FIRE HYDRANT
STONCLAD UT CONSISTS OF A URETHANE-UREA BINDER, PIGMENTS AND
9640

9640

9640
NEW BRICK WALL
Cabinet

Cabinet
GRADED QUARTS AGGREGATES. STONCLAD UT IS A NOMINAL 5MM SYSTEM.

Cabinet

Cabinet

Cabinet
Cove Base:
NEW TIMBER • Cove bases in heights from 15cm – refer to Stonshield 980 Coving Resin
Tuck Shop Tuck Shop
Cabinet

Cabinet

Cabinet

Cabinet

34 m² Textures: 34 m²
NEW CONCRETE

Cabinet
Screed • Light textures Screed • ALL FIRE WALLS SHALL HAVE 2HOURS FIRE RATED
• Coated with Stonkote HT4 FULL HEIGHT WALL TO THE UNDERSIDE OF THE ROOF
• Light texture, 25kg Stonhard 6221, 2 to 3kg/m² • WALL TO BE FIRE RATED PARTITION BOARDS.
Cabinet

NEW IRON/STEEL
5510

5510

5510

5510

5510
5960
• ALL FIRE DOORS TO BE 2HOURS FIRE RATED, HAVE

FHR
Sealer: SELF-CLOSING MECHANISM AND APPROVED LOCKING
• 2 litre kit Stonkote HT4, 972 Parts A & B, 4 to 6m²/litre/coat DEVICES (PUSH PLATES AND PANIC BARS)
DEMOLITION
A trial reference sample should be installed by the Applicator prior to start of contract
to ensure correct coverage and workmanship.
NEW SOIL PIPE WORK AND

COUNTER
SANITARY FITTINGS
COUNTER

NEW BELOW GROUND FE FE


PIPEWORK AND DRAINS
Trench Drain ELD
FE FE FHR
NEW SEWER LINE Trench Drain D3
RSD • 304 stainless steel grates
REVISIONS
230

230

230

230

230
• Stainless Steel Channel
D3 NEW WATER LINE • 39cm(W) x 13cm(H)
230 6310 230
REV DESCRIPTION BY DATE
230 6310 230
EX. EXISTING
6770

IE. INSPECTION EYE

GROUND FLOOR FIRE PROTECTION LAYOUT


RE. RODDING EYE 1 : 50
1 : 50

D1 TYPE STANDARD SINGLE FIRE DOOR WITH CLEAR D3 TYPE STANDARD SINGLE FIRE DOOR WITH CLEAR D3 TYPE DOUBLE DOOR:
OPENING OF 813mmX2100mm WITH 3HR FIRE RATING OPENING OF 900mmX2100mm WITH 3HR FIRE RATING WITH CLEAR OPENING OF 2700mm (H) x 2500mm (W)
GLAZING N/A
GLAZING N/A GLAZING N/A
FRAME TYPE PRESSED STEEL FRAME THICKNESS TO BE 4mm,
FRAME TYPE PRESSED STEEL FRAME THICKNESS TO BE 4mm, FRAME TYPE PRESSED STEEL FRAME THICKNESS TO BE 4mm, GALVANIZED AND PRIME COATED.
INTUMESCENT STRIP AND COLD SMOKE SEAL INTUMESCENT STRIP AND COLD SMOKE SEAL
FRAME FINISH GALVANIZED AND PRIME COATED.
FRAME FINISH POWDER COATED-SILVER FINISH FRAME FINISH POWDER COATED-SILVER FINISH DOOR FINISH GARAGE DOOR ROLL UP ALUZINC BROWN, HEADER
SEAL AND PRIME COATED WINDING SHAFTROLLER
DOOR FINISH STEEL SHEET THICKNESS TO BE MIN 2mm WITH DOOR FINISH STEEL SHEET THICKNESS TO BE MIN 2mm WITH
SHUTTER, 0.8MM STANDARD STEEL SLAT
TOTAL DOOR LEAF THICKNESS OF 50mm, MAINTAIN TOTAL DOOR LEAF THICKNESS OF 50mm, MAINTAIN
SOUNDREDUCTION RW-37-45DB SOUNDREDUCTION RW-37-45DB DOOR FURNITURE PVC BOX MATERIAL, MANUAL OPPENING SYSTEM,
BROWN EXTERIOR FACE COLOUR, 400x400x3050 case
DOOR FURNITURE CAM ACTION CLOSER EN1-4 SIL, OPENING DAMPER, DOOR FURNITURE CAM ACTION CLOSER EN1-4 SIL, OPENING DAMPER, size, 390mm MIN LINTEL HEADROOM, BEEHIVE ROL-
CYLINDER PROFILE GMK, PANIC LATCH P/BAR CYLINDER PROFILE GMK, PANIC LATCH P/BAR LOCK/BARREL LOCK, STEEL T BAR, MANUAL PUSH
900mm, UNION OUTSIDE ACCESS DEVICE FOR PANIC 900mm, UNION OUTSIDE ACCESS DEVICE FOR PANIC AND/OR PULL OPERATION OPTION AVAILABLE, CHAIN SURVEYED
BOLT, HEAVY DUTY 3 HINGES AND 3 POINT LATCH BOLT, HEAVY DUTY 3 HINGES AND 3 POINT LATCH OPERATED DESIGNED
ACTION: ACTION: ACTION: DRAWN
NEW 3 NEW 1 NEW 1 CHECKED
REFURBISH 0 REFURBISH 0 REFURBISH 0 SERVICE CHECKED
GEOTECHNICAL INVESTIGATION
SERVITUDES

APPROVED

Pr.Arch. No.

DATE

ALL NATION
SUPERMARKET SHOP
14, Northend Grove,
Blyvoor

Copyright reserved by Zitholele Consulting


ALL NATION TUCK SHOP
ALL NATION TUCK SHOP Scales 100mm on original drawing

ALL NATION
SUPERMARKET SHOP

SHOP LAYOUT

Front Elevation Side Elevation FLOOR PLAN


1 : 50 1 : 50
EMERGENCY ROUTE PLAN

CONSULTANT'S NUMBER

CLIENT'S NUMBER SHEET NUMBER


101-S.1
SCALE REVISION

C:\Users\SirakTaddese\OneDrive - Zitholele Consulting\Desktop\All Sirak Files\Tuck Shops\No.9-Tuck Shop.Rev 0 - All Nation Supermarket Shop.rvt

You might also like