Scribd
Upload
13 views6 pages

Circuit 2

Uploaded by

oahmd265
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
13 views6 pages

Circuit 2

Uploaded by

oahmd265
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

MCH205 Electrical Circuits 2, Elec. & Electronics Dept.

, Faculty of Technology & Education- Suez University

Electrical Circuits 2
Assignment # 4

1-For the circuit in Fig.1, find:


(a) i(o+) and v(o+),
(b) di (o+) / dt and dv(o+) / dt,
(c) i(∞) and v(∞). Figure 1-problem-1

2-Refer to the circuit shown in Fig.2. Calculate:

(a) iL(o+) and vC (o+), and vR (o+),


(b) diL (o+) / dt and dvC (o+) / dt, and dvR (o+) / dt,
(c) iL(∞) and vC(∞).and vR(∞).
Figure 2-problem-2

3- Refer to the circuit shown in Fig.3. Determine:

(a) i(o+) and v(o+),


(b) di (o+) / dt and dv(o+) / dt,
(c) i(∞) and v(∞).

Figure 3-problem-3

4 -In the circuit of Fig. 4, find:


(a) vR (o+), and vL (o+),
(b) dvR(o+) / dt, and dvL(o+) / dt,
(c) vR(∞).and vL(∞).

Figure 4-Problem-4
5-A series RLC circuit has R=20KΩ, L=0.2mH , and C=5μF. What type of
damping is exhibited by the circuit?

6- The current in an RLC circuit is described by

If i(o)= 10A and di (o) / dt= 0 find for i(t) for t >0.

7- If R=50KΩ, L=1.5H , what value of C will make


an RLC series circuit:
(a) overdamped,
(b) critically damped,
(c) underdamped?

8- For the circuit in Fig. 5, calculate the value of R


needed to have a critically damped response.

Figure 5-problem-8

9- The switch in Fig. 6 moves from position A to position B at t=0 (please note that the
switch must connect to point B before it breaks the connection at
A, a make-before-break switch). Let v(0) = 0, find v(t) for t.> 0.

Figure 6-problem-9
10- The switch in the circuit of Fig. 7 has been closed
for a long time but is opened at Determine
i(t) for t >0.

Figure 7-problem-10

11-Assuming design a parallel RLC circuithat has the characteristic equation.

12-For the network in Fig. 8, what value of C is needed to make the response
underdamped with unity damping factor (α=1 )?

Figure 8-problem-12

13-The switch in Fig. 9 moves from position A to position B at t= 0 (please note that
the switch must connect to point B before it breaks the connection at A, a make-
before-break switch). Determine i(t) for t >0.

Figure 9-problem -13


14-The step response of an RLC circuit is given by

Given that i(o)= 2A and di (o) / dt= 4 ,solve for i(t).


15- A series RLC circuit is described by

16-The step responses of a series RLC circuit are

(a) Find C. (b) Determine what type of damping is


exhibited by the circuit.

17-Calculate i(t)for t >0 in the circuit of Fig.10

Figure 10-problem -17

18-Obtaini(t) and v(t)for in the circuit of Fig. 11.

Figure 11-problem-18
19-Determine v(t) for t >0 in the circuit of Fig. 12.

Figure12 -problem-19

20-In the circuit of Fig. 13, find i(t)and v(t) for t >0 Assume and v(0) = 0 V and
i(0) =1 A.

Figure 13-problem-20
21-Find the output voltage vo(t) in the circuit of Fig. 14.

Figure 14-problem-21

22-Determine i(t) for t >0 in the circuit of Fig. 15.

Figure 15-problem -22


23- Find v(t) for t >0 in the circuit of Fig. 16.

Figure 16-problem - 23

24- If the switch in Fig. 17 has been closed for a long time before t = 0 but is opened
at determine:
(a) the characteristic equation of the circuit,
(b) ix and vR for t > 0.

Figure 17-problem-24

25- In the circuit of Fig. 18, the switch has been in position 1 for a long time but
moved to position 2 at t =0 Find:

(a) v(0+), dv(0+)dt,


(b) for v(t) t > 0.

Figure 18-problem-25

You might also like