A COMPANY

Harness - Eng MX EPA '04 P92-5156 A 01

© 2009 PACCAR Inc – All Rights Reserved – The information contained in this drawing is proprietary to PACCAR. Reproduction, in whole or in part, by any means is strictly prohibited without prior written authorization from PACCAR Inc.

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

L GENERAL NOTES: L
1) USE ON T8 / T6 MODELS WITH NAMUX 3
INSTRUMENTATION AND MX EPA '04 ENGINES
WITH ETC3-C ENGINE CONTROLLER.
HARNESS VARIATION TABLE
2) HARNESS SHALL CONFORM TO R026-170-18.
TABLE A ( PRODUCTION STATUS )
3) HARNESS SHALL CONFORM TO R026-170-146.
- ALL CONDUCTORS TO BE GXL EXCEPT IF NOTED VERSION STATUS
OTHERWISE IN THE WIRE INFORMATION TABLE.
- HARNESS COVERINGS PER 9.0C. 1 PRODUCTION
K - SECTION 3.0 CIRCUIT IDENTIFICATION SHALL ONLY APPLY K
WHEN IDENTIFYING CIRCUITS PER WIRING CIRCUIT TABLE B ( OPTIONS )
CHART R076-3315, OTHERWISE PACCAR CDS0124 SHALL
OMIT OMIT
BE APPLIED FOR CIRCUIT IDENTIFICATION. VAR USAGE
CIRCUITS COMPONENTS
4) PART MARKING AND TRACEABILITY REQUIREMENTS 0 GRA3123-0 P119, P20-1040 W/O ETHER START
SHALL COMPLY WITH CPS0098. ALSO APPLY W/O TWO SPEED REAR AXLE
KENWORTH TRADEMARK AS DESCRIBED IN R026-198-120. GRN3123-0 J119, P67-1005-102-2 W/ MULTIFUNCTION ENGINE CONNECTOR
BLU3631-0 P168, K333-550-202
5) PAPER TAGS SHALL BE APPLIED TO THE HARNESS WITHIN YEL3631-0 J168, K333-550-102
75mm FROM THE BASE OF THE CONNECTOR AND SHOULD BE
CLEARLY VISIBLE UPON COMPLETION OF THE HARNESS. PAPER 1 NONE NONE W/ ETHER START *OR* W/ TWO SPEED REAR AXLE
J TAG ALL BREAKOUTS WITH CORRESPONDING "LABEL" STATEMENT W/ MULTIFUNCTION ENGINE CONNECTOR J
IN THE CONNECTOR TABLE.
2 BLU3144-0 P124, K333-584-1 W/O ETHER START
6) THE FOLLOWING CIRCUITS ARE PART OF A TWISTED PAIR, W/O TWO SPEED REAR AXLE
JACKETED CABLE ASSEMBLY. USE CABLE P/N P92-2197. NO LOOPING GRA3512-0 J124, K333-612-1 W/O MULTIFUNCTION ENGINE CONNECTOR
OF CABLE ASSEMBLY OR WIRES IN HARNESS ASSEMBLY. NO UNTWISTED
GRA3513-0 P119, P20-1040
SECTIONS OF WIRE IN EXCESS OF 50mm AFTER STRIPPING JACKET
WHT1513-2 J119, P67-1005-102-2
ORN1229-2 P168, K333-550-202
VIO4500-2 J168, K333-550-102
I YEL0812-0, GRN0812-0,
GRN4500-2 I
C
YEL3511-0
YEL0812-4, GRN0812-4, C GRA3511-1
YEL0818-6, GRN0818-6, C GRA3123-0
YEL0818-9, GRN0818-9, C
GRN3123-0
BLU3631-0
YEL0818-11, GRN0818-11, C
YEL3631-0
YEL0852-3, GRN0852-3, C
3 W/ ETHER START *OR* W/ TWO SPEED REAR AXLE
BLU3144-0 P124, K333-584-1
W/O MULTIFUNCTION ENGINE CONNECTOR
GRA3512-0 J124, K333-612-1
H GRA3513-0
H
7 CONNECTORS TO BE MATED BY HARNESS MANUFACTURER.
WHT1513-2
8 TAPE J1939 CONNECTORS ( J114 & P114 ) WITH ORN1229-2
BLUE TAPE TO THE MAIN HARNESS BUNDLE OVER THE LOCKING LATCH. VIO4500-2
VERIFY WIRES ARE NOT STRAINED AT THE CONNECTOR.
GRN4500-2
9 USE K344-813-6 ON 250mm SECTION FROM BACK OF P20-1211-002. YEL3511-0
CAPTURE CONVOLUTE IN BACKSHELL OF P20-1211-002 AS DEFINED BY GRA3511-1
COMPONENT MANUFACTURER. SECURE ENDS WITH VINYL TAPE. AR - VINYL TAPE BLACK, ADHESIVE BACKED
ORIENT THE SLIT ON THE CONVOLUTE SO THAT IT FACES TO THE TABLE C ( DATALOGGER ) AR - K344-813 CONVOLUTED TUBING
G LEFT WHEN THE CONNECTOR IS VIEWED AS IN THE MATING VIEW. G
OMIT OMIT
VAR USAGE AR - TAPE BLUE, ADHESIVE BACKED
10) THE USE OF CAVITY PLUGS ON ALL UNUSED CAVITIES IS REQUIRED. CIRCUITS COMPONENTS
0 GRN0852-3 J174, K333-562-208-1 W/O DATALOGGER
11) LEGEND: AR - TAPE BLACK, ADHESIVE BACKED
YEL0852-3
AR - P92-2197 ASSY, CABLE, J1939 / 15 LITE
TWISTED PAIR GRN0818-6
YEL0818-6 1 T133 K333-46-19 RING, TERMINAL, ( 5 / 16" )
1 NONE NONE W/ DATALOGGER
TWISTED TRIPLE 1 T121 322768 RING, TERMINAL, AMP SOLISTRAND, BENT 90 ( # 10 )

F 1 P712 K333-562-202-1 PACKARD, METRI - PACK 150 SERIES, 2 - WAY, SEALED F

TWISTED JACKETED PAIR 1 P168 K333-550-202 PACKARD, METRI - PACK 280 SERIES, 2 - WAY, SEALED

DETAIL "D" 1 P148 P20-1258-1107-17303 AMP HDSCS SERIES, 7 - WAY, SEALED ( 1 - 1418480 - 1 )
12 SHIP WITH YELLOW SLIDE LOCK OUT. CONNECTOR KEYING & BACKSHELL ORIENTATION 1 P124 K333-584-1 DEUTSCH DT SERIES, 12 - WAY, SEALED ( PB # 16 - 06777 )
13 EACH CONNECTOR WITH A BACKSHELL OR BOOT SHALL CAPTURE CONVOLUTE 90 KEY 1 P119 P20-1040 PACKARD, METRI - PACK 150 SERIES, 2 - WAY, SEALED
AS DEFINED BY COMPONENT MANUFACTURER. CONVOLUTE FOR EACH BREAKOUT
SHALL BE SIZED TO BE CORRECTLY CAPTURED REGUARDLESS OF WIRE BUNDLE DEG 1 P118 P20-1040 PACKARD, METRI - PACK 150 SERIES, 2 - WAY, SEALED
SIZE. SECURE CONVOLUTE TO BACKSHELL, BOOT OR BUNDLE WITH VINYL TAPE.
E 14) ALL TERMINALS SHALL USE TIN PLATING UNLESS NOTED OTHERWISE IN THE
1 P114 P20-1193-1202G AMP SUPERSEAL 1.5K SERIES, 2 - WAY, SEALED E
WIRE INFORMATION TABLE.
1 P107 K333-550-202 PACKARD METRI - PACK 280 SERIES, 2 - WAY, SEALED
180
15) PART NUMBER IS GENERATED BY THE FOLLOWING: 1 P103 P20-1133-47-5-2 DEUTSCH HDP20 SERIES, 47 - WAY, SEALED
DEG
SEE TABLE A ( PRODUCTION STATUS ) 1 P101 P20-1211-002 AMP MCP SERIES, 62 - WAY, SEALED
SEE TABLE B ( OPTIONS )
SEE TABLE C ( DATALOGGER )
( P103 )
0 1 J175 P20-1134-21-3-0 DEUTSCH, HDP SERIES, 21 - WAY, SEALED
DEG 1 J174 K333-562-208-1 PACKARD METRI - PACK 150 SERIES, 8 - WAY, SEALED
D 1 J168 K333-550-102 PACKARD, METRI - PACK 280 SERIES, 2 - WAY, SEALED D
P92-5156 -ABC 270
DEG 1 J149 P20-1258-2106-10103 AMP HDSCS SERIES, 6 WAY, SEALED ( 1 - 1703773 - 1 )
EXAMPLE: P92-5156-111 IS AN ENGINE HARNESS
WITH A ETHER START, 2 SPEED REAR 1 J124 K333-612-1 DEUTSCH DT SERIES, 12 - WAY, SEALED ( PB # 16 - 06778 )
AXLE AND WITH A DATALOGGER.
1 J119 P67-1005-102-2 PACKARD, METRI - PACK 150 SERIES, 2 - WAY, SEALED

16) EMISSION-RELATED PART CODE: [ N ], SEE CPS0374 FOR REQUIREMENTS 1 J118 P20-1193-1105T AMP SUPERSEAL 1.5K SERIES, 5 WAY, SEALED

17 USE WITH ON / OFF FAN HUB. 1 J114 P20-1193-1102G AMP SUPERSEAL 1.5K SERIES, 2 - WAY, SEALED
C C
1 C04 W62-1000-1 MOUNT, FIR TREE, TAPE ON

1 C03 156-00074 MOUNT, FIR TREE, CABLE TIE ( HELLERMANN - TYTON # )

1 C02 156-00074 MOUNT, FIR TREE, CABLE TIE ( HELLERMANN - TYTON # )

1 B03 15327799 DELPHI BACKSHELL, PLASTIC

1 B02 493581-1 TYCO BOOT, RUBBER

1 B01 P22-1009 DEUTSCH BACKSHELL 90 - DEGREES, HDP20

B B

A A
DWG
SIZE
A0
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
 A COMPANY
Harness - Eng MX EPA '04 P92-5156 A 02
© 2009 PACCAR Inc – All Rights Reserved – The information contained in this drawing is proprietary to PACCAR. Reproduction, in whole or in part, by any means is strictly prohibited without prior written authorization from PACCAR Inc.

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

L USAGE NOTE: L
USE ON T8 / T6 MODELS WITH NAMUX 3
INSTRUMENTATION AND MX EPA '04 ENGINES
WITH ETC-3 ENGINE CONTROLLER. CORRECT
INCORRECT

WIRE INFORMATION FOR HARNESS: P92-5156-000

K CIRCUIT FROM TERM TO TERM WIRE WIRE WIRE K
TERM TERM DESCRIPTION
NUMBER COMPONENT PLATE COMPONENT PLATE SIZE GAUGE TYPE
BLK3216-1 J175 P20-1134-21-3-0 J NI P148 P20-1258-1107-17303 4 AG 0.8mm^2 ( 18 ) TXL FUEL METERING VLV RTN
BLU3141-0 P101 P20-1211-002 49 AG P103 P20-1133-47-5-2 22 AU 0.8mm^2 ( 18 ) TXL THROTTLE SENSE POS
BLU3142-0 P101 P20-1211-002 45 AG P103 P20-1133-47-5-2 14 AU 0.8mm^2 ( 18 ) TXL IDLE VALIDATION SIG
BLU3144-0 P124 K333-584-1 4 P103 P20-1133-47-5-2 39 0.8mm^2 ( 18 ) GXL REMOTE THROTTLE SIGNAL
BLU3631-0 P101 P20-1211-002 10 AG P168 K333-550-202 B 0.8mm^2 ( 18 ) TXL REAR AXLE HI / LO SIGNAL
BLU4381-0 P101 P20-1211-002 27 AG J175 P20-1134-21-3-0 V AU 0.8mm^2 ( 18 ) TXL WIF SENSE
BLU4527-0 J149 P20-1258-2106-10103 5 AG P103 P20-1133-47-5-2 7 0.8mm^2 ( 18 ) TXL OAT SENSE
J BRN4311-0 P101 P20-1211-002 4 AG P103 P20-1133-47-5-2 42 0.8mm^2 ( 18 ) TXL CHECK ENGINE LAMP
DETAIL A J
INSTALL TERMINALS AND ROUTE
BRN4312-0 P101 P20-1211-002 8 AG P103 P20-1133-47-5-2 43 0.8mm^2 ( 18 ) TXL STOP ENGINE LAMP WIRES SUCH THAT WIRE SEALS ARE
BRN4330-0 P101 P20-1211-002 23 AG P103 P20-1133-47-5-2 3 0.8mm^2 ( 18 ) TXL OBD MIL NOT STRESSED OR BEING PULLED.
GRA3112-0 P101 P20-1211-002 3 AG J175 P20-1134-21-3-0 T NI 0.8mm^2 ( 18 ) TXL ENG ECU RELAY
GRA3123-0 P119 P20-1040 A J149 P20-1258-2106-10103 1 AG 0.8mm^2 ( 18 ) TXL ETHER START SOLENOID CONTROL
GRA3191-0 P118 P20-1040 B J118 P20-1193-1105T 3 1.0mm^2 ( 16 ) GXL FAN HUB
GRA3192-2 P101 P20-1211-002 6 AG P712 K333-562-202-1 A 0.8mm^2 ( 18 ) TXL MAN FAN SW / AC PRESS SW HARNESS BUNDLE
GRA3216-1 J175 P20-1134-21-3-0 H NI P148 P20-1258-1107-17303 5 AG 0.8mm^2 ( 18 ) TXL FUEL METERING VALVE
GRA3511-1 P101 P20-1211-002 21 AG P124 K333-584-1 5 0.8mm^2 ( 18 ) TXL PTO ON / OFF SLIT IN COVOLUTE
I GRA3512-0 P124 K333-584-1 2 P103 P20-1133-47-5-2 37 0.8mm^2 ( 18 ) GXL REMOTE PTO SET I
GRA3513-0 P124 K333-584-1 1 P103 P20-1133-47-5-2 38 0.8mm^2 ( 18 ) GXL REMOTE PTO RESUME
GRA3912-1 P103 P20-1133-47-5-2 10 T121 322768 1 1.0mm^2 ( 16 ) GXL START CTRL RLY TO STRT RLY
GRA4584-2 P101 P20-1211-002 25 AG S06 SPLICE 1 0.8mm^2 ( 18 ) TXL CLUTCH SWITCH
GRN0812-0 P103 P20-1133-47-5-2 30 AU P114 P20-1193-1202G 1 AU 0.75mm^2 ( 19 ) XLPOLYO J1939 V-CAN ( - )
GRN0812-4 P101 P20-1211-002 55 AG J114 P20-1193-1102G 1 AU 0.75mm^2 ( 19 ) XLPOLYO J1939 V-CAN ( - )
GRN0818-6 J174 K333-562-208-1 E AU S32 SPLICE 1 0.75mm^2 ( 19 ) XLPOLYO J1939 A-CAN ( - )
GRN0818-9 S32 SPLICE 1 J175 P20-1134-21-3-0 R AU 0.75mm^2 ( 19 ) XLPOLYO J1939 A-CAN ( - )
GRN0818-11 P101 P20-1211-002 56 AG S32 SPLICE 1 0.75mm^2 ( 19 ) XLPOLYO J1939 A-CAN ( - )
H GRN0852-3 P101 P20-1211-002 37 AG J174 K333-562-208-1 F AU 0.75mm^2 ( 19 ) XLPOLYO J1939 HS-CAN ( - )
H
GRN3123-0 J149 P20-1258-2106-10103 2 AG P119 P20-1040 B 0.8mm^2 ( 18 ) TXL ETHER START SOLENOID GND
GRN3141-0 P101 P20-1211-002 42 AG P103 P20-1133-47-5-2 23 AU 0.8mm^2 ( 18 ) TXL THROTTLE SENSE RETURN
GRN4381-0 J175 P20-1134-21-3-0 U AU P101 P20-1211-002 32 AG 0.8mm^2 ( 18 ) TXL WIF RETURN
GRN4500-2 P124 K333-584-1 3 P103 P20-1133-47-5-2 24 0.8mm^2 ( 18 ) GXL NAMUX ANALOG RETURN
GRN4527-0 J149 P20-1258-2106-10103 6 AG P103 P20-1133-47-5-2 8 0.8mm^2 ( 18 ) TXL OAT RETURN C04
ORN1229-2 P124 K333-584-1 7 P103 P20-1133-47-5-2 1 2.0mm^2 ( 14 ) GXL BODY IGN POWER ( 10A )
ORN3112-0 P101 P20-1211-002 1 AG S06 SPLICE 1 0.8mm^2 ( 18 ) TXL ECU WAKE UP
SECTION B-B
INSTALL FIR TREE C04 AND
ORN3112-1 S06 SPLICE 1 P103 P20-1133-47-5-2 21 0.8mm^2 ( 18 ) TXL ECU WAKE UP ( 5A )
G SECURE TO CONVOLUTE WITH G
RED3110-1 P101 P20-1211-002 43 AG J175 P20-1134-21-3-0 W NI 0.8mm^2 ( 18 ) TXL LPC BATT POWER ( 5A ) CABLE TIES AND TAPE.
VIO3141-0 P101 P20-1211-002 38 AG P103 P20-1133-47-5-2 12 AU 0.8mm^2 ( 18 ) TXL THROTTLE SENSE SUPPLY 155± 5
VIO3142-3 P101 P20-1211-002 46 AG P103 P20-1133-47-5-2 13 AU 0.8mm^2 ( 18 ) TXL IDLE VALIDATION SW
VIO4500-2 P124 K333-584-1 10 P103 P20-1133-47-5-2 28 0.8mm^2 ( 18 ) GXL NAMUX POWER SUPPLY ( +5V )
WHT1513-1 T133 K333-46-19 1 S07 SPLICE 1 13.0mm^2 (6) SGX ENGINE GND
WHT1513-2 P124 K333-584-1 8 S07 SPLICE 1 2.0mm^2 ( 14 ) GXL GROUND
WHT1513-3 S02 SPLICE 1 S07 SPLICE 1 5.0mm^2 ( 10 ) GXL ECU RETURN ( - )
WHT3110-0 P101 P20-1211-002 7 AG S02 SPLICE 1 0.8mm^2 ( 18 ) TXL CASE GND
F WHT3111-1 P101 P20-1211-002 59 AG S02 SPLICE 1 2.0mm^2 ( 14 ) TXL ECU RETURN ( - ) F
WHT3111-2 P101 P20-1211-002 58 AG S02 SPLICE 1 2.0mm^2 ( 14 ) TXL ECU RETURN ( - )
WHT3111-3 P101 P20-1211-002 57 AG S02 SPLICE 1 2.0mm^2 ( 14 ) TXL ECU RETURN ( - )
WHT3198-1 S07 SPLICE 1 P148 P20-1258-1107-17303 7 AG 0.8mm^2 ( 18 ) TXL HUMIDITY SENSOR ECU RTN
J149
WHT3215-0 S07 SPLICE 1 P148 P20-1258-1107-17303 3 AG 2.0mm^2 ( 14 ) TXL VGT ACTUATOR GND
WHT7111-0 S07 SPLICE 1 P107 K333-550-202 A 2.0mm^2 ( 14 ) GXL A / C CLUTCH GND
YEL0812-0 P103 P20-1133-47-5-2 31 AU P114 P20-1193-1202G 2 AU 0.75mm^2 ( 19 ) XLPOLYO J1939 V-CAN ( + )
YEL0812-4 P101 P20-1211-002 47 AG J114 P20-1193-1102G 2 AU 0.75mm^2 ( 19 ) XLPOLYO J1939 V-CAN ( + )
YEL0818-6 J174 K333-562-208-1 D AU S31 SPLICE 1 0.75mm^2 ( 19 ) XLPOLYO J1939 A-CAN ( + )
E YEL0818-9 S31 SPLICE 1 J175 P20-1134-21-3-0 S AU 0.75mm^2 ( 19 ) XLPOLYO J1939 A-CAN ( + ) P148 E
YEL0818-11 P101 P20-1211-002 48 AG S31 SPLICE 1 0.75mm^2 ( 19 ) XLPOLYO J1939 A-CAN ( + )
YEL0852-3 P101 P20-1211-002 29 AG J174 K333-562-208-1 G AU 0.75mm^2 ( 19 ) XLPOLYO J1939 HS-CAN ( + )
YEL3111-0 S03 SPLICE 1 J175 P20-1134-21-3-0 E NI 3.0mm^2 ( 12 ) GXL ENG ECU PWR ( 25A ) BREAKOUT FROM MAIN BUNDLE MAIN HARNESS BUNDLE
YEL3111-2 P101 P20-1211-002 62 AG S03 SPLICE 1 2.0mm^2 ( 14 ) TXL ECU SUPPLY ( + )
YEL3111-3 P101 P20-1211-002 61 AG S03 SPLICE 1 2.0mm^2 ( 14 ) TXL ECU SUPPLY ( + )
YEL3111-4 P101 P20-1211-002 60 AG S03 SPLICE 1 2.0mm^2 ( 14 ) TXL ECU SUPPLY ( + ) C02, C03
YEL3116-0 J175 P20-1134-21-3-0 D NI S18 SPLICE 1 3.0mm^2 ( 12 ) GXL ENGINE POWER ( 20A )
YEL3191-0 J118 P20-1193-1105T 4 P118 P20-1040 A 1.0mm^2 ( 16 ) TXL FAN SOLENOID PWR
D YEL3192-0 S06 SPLICE 1 P712 K333-562-202-1 B 0.8mm^2 ( 18 ) TXL MAN FAN SW / AC PRESS SW D
YEL3198-1 S18 SPLICE 1 P148 P20-1258-1107-17303 1 AG 2.0mm^2 ( 14 ) TXL VGT ACTUATOR PWR
YEL3198-2 S18 SPLICE 1 P148 P20-1258-1107-17303 2 AG 2.0mm^2 ( 14 ) TXL ENG ACT / SNSR PWR FT9B
YEL3511-0 P124 K333-584-1 11 S18 SPLICE 1 2.0mm^2 ( 14 ) GXL ENG SYS POWER
YEL3631-0 P168 K333-550-202 A S06 SPLICE 1 0.8mm^2 ( 18 ) GXL RAX PRESS SW POWER
YEL7111-0 P107 K333-550-202 B P103 P20-1133-47-5-2 4 2.0mm^2 ( 14 ) GXL A / C COMPRESSOR CLUTCH SECTION C-C
INSTALL FIR TREE C02 AND SECURE
TO CONVOLUTE WITH CABLE TIE IN
ORIENTATION SHOWN. INSTALL
C C03 SAME ORIENTATION AS C02. C

B B

A A
DWG
SIZE
A0
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
 A COMPANY
Harness - Eng MX EPA '04 P92-5156 A 03
© 2009 PACCAR Inc – All Rights Reserved – The information contained in this drawing is proprietary to PACCAR. Reproduction, in whole or in part, by any means is strictly prohibited without prior written authorization from PACCAR Inc.

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

P103
L B01 SEE DETAIL D L
SHEET 1, ZN E-10
FOR CONNECTOR
TERMINAL INFORMATION FOR: P712 ORIENTATION
USAGE NOTE: K333-562-202-1, GRAY, ( 2 CAVITIES )
USE ON T8 / T6 MODELS WITH NAMUX 3 TERMINAL INFORMATION FOR: J149 LABEL: P712, A / C PRESSURE SWITCH ( ECU FAN CTL ) TERMINAL INFORMATION FOR: P103
INSTRUMENTATION AND MX EPA '04 ENGINES P20-1258-2106-10103, BLACK, ( 6 CAVITIES ) P20-1133-47-5-2, BLACK, ( 47 CAVITIES ) TERMINAL INFORMATION FOR: J175
WITH ETC-3 ENGINE CONTROLLER. TERM CIRCUIT NO. LABEL: P103, DASH HARNESS P20-1134-21-3-0, BLACK, ( 26 CAVITIES )
LABEL: J149, APPLICATION SIGNAL
LABEL: J175, CHASSIS HARN
TERM CIRCUIT NO. TERM CIRCUIT NO.
A GRA3192-2 TERM CIRCUIT NO.
2 GRN3123-0 35 34 47 10 GRA3912-1
4 1 5 B YEL3192-0 36 20 33 46 D YEL3116-0
BLU4527-0 8 32 30 GRN0812-0
K 6 GRN4527-0
22
21
9 19
31
31 YEL0812-0
H GRA3216-1 K
10 2 18 H
37 23 30 45 X J J BLK3216-1
1 GRA3123-0 3 7 1 ORN1229-2 SECURE 90° BACKSHELL
11 17 29 U GRN4381-0
24
1 3 BRN4330-0 WITH 2 NYLON TIES W K
6 3 38 44 G B E YEL3111-0
12 4 6 16 4 YEL7111-0 V L
MATING VIEW 39 25 13 5 15 28 43
7 BLU4527-0 ( CONVOLUTED TUBING ) F A C R GRN0818-9
J175
J118 14 27 42 U M S YEL0818-9
40 8 GRN4527-0 E
TAG HERE D T GRA3112-0
26 12 VIO3141-0 T N
41
TERMINAL INFORMATION FOR: P148 V BLU4381-0
P20-1258-1107-17303, BLACK, ( 7 CAVITIES ) 13 VIO3142-3 S P
R W RED3110-1
LABEL: P148, APPLICATION POWER 14 BLU3142-0
J 1
P712
MATING VIEW J
4 TERM CIRCUIT NO. 21 ORN3112-1
22 BLU3141-0 300
1 YEL3198-1 23 GRN3141-0
2 YEL3198-2 24 GRN4500-2 MATING VIEW
3 WHT3215-0 B A
28 VIO4500-2
7
4 BLK3216-1 37 GRA3512-0
TERMINAL INFORMATION FOR: P107 3 5 GRA3216-1 400
38 GRA3513-0 300
K333-550-202, BLACK, ( 2 CAVITIES )
LABEL: P107, AC COMPRESSOR CLUTCH 7 WHT3198-1 39 BLU3144-0 J174
I TERM CIRCUIT NO. 42 BRN4311-0 I
B YEL7111-0 275 43 BRN4312-0 TERMINAL INFORMATION FOR: J174

D CB A
K333-562-208-1, BLACK, ( 8 CAVITIES )
TERMINAL INFORMATION FOR: T133 A WHT7111-0 MATING VIEW
12 B02 LABEL: J174, DATALOGGER HARNESS
K333-46-19, 5 / 16" TERMINAL, TYPE B 600
TERM CIRCUIT NO.
LABEL: T133, ENGINE GROUND TERMINAL INFORMATION FOR: J118 E H
P148 D YEL0818-6
TERM CIRCUIT NO. 475 P20-1193-1105T, BLACK, ( 5 CAVITIES )
P107 LABEL: J118, ENGN FAN BREAKOUT E GRN0818-6
1 WHT1513-1
TERM CIRCUIT NO. D A F GRN0852-3
T133 4 YEL3191-0 MATING VIEW G YEL0852-3
A B J149 5
750
H 4
3 GRA3191-0 H
3
350 SEE HARNESS VARIATION TABLE
LOCATEC02 2
TAPE BACK FOR OMISSION INFORMATION
HERE 350 P118
1
300 800
TERMINAL INFORMATION FOR: T121 200 TERMINAL INFORMATION FOR: P118
322768, # 10 TERMINAL, TYPE A FOR VIEW, SEE 300 MATING VIEW
800 B03 P20-1040, BLACK, ( 2 CAVITIES )
SHEET 2, ZONE C-7

A
LABEL: T121, STARTER RELAY ( COIL ) LABEL: P118, ENGINE FAN SOLENOID
LOCATE C03

B
TERM CIRCUIT NO. HERE TERM CIRCUIT NO.
1 GRA3912-1 TAPE BACK INSERT SPLICE J168 B GRA3191-0
G C TAPE BACK S31 AND S32 HERE G
A YEL3191-0
1000 150 400 420 230 100± 30
7

P168
C TERMINAL INFORMATION FOR: P124 300
T121 K333-584-1, GRAY, ( 12 CAVITIES )
P124
130± 5
LOCATE SPLICE LABEL: P124, REMOTE PTO / THROTTLE TERMINAL INFORMATION FOR: P168
S02 & S03 290± 5 K333-550-202, BLACK, ( 2 CAVITIES )
TERM CIRCUIT NO. LABEL: P168, RAX RATIO HI/LOW SW
F K344-813 1 12 1 GRA3513-0 TERM CIRCUIT NO. F
EXCEPT WHERE 2 GRA3512-0 J124
A YEL3631-0
NOTED 3 GRN4500-2 B BLU3631-0
4 BLU3144-0 150
6 7 7 ORN1229-2 SEE HARNESS VARIATION TABLE
7 FOR OMISSION INFORMATION.
9 8 WHT1513-2 600
250
MATING VIEW 10 VIO4500-2
TERMINAL INFORMATION FOR: P101
P20-1211-002, GREY, ( 62 CAVITIES ) 11 YEL3511-0
LABEL: P101, ENG ECU ( OEM ) "PORT J2" 5 GRA3511-1 2 1
E TERM CIRCUIT NO. J114 E
FOR VIEW, SEE 1 ORN3112-0 B
SHEET 2, ZONE H-8 3 GRA3112-0
A
4 BRN4311-0 TERMINAL INFORMATION FOR: J114
B B
6 GRA3192-2 P20-1193-1102G, BLACK, ( 2 CAVITIES )
LABEL: J114, J1939 V-CAN
7 WHT3110-0 250 P119
LOCATE C04 4 TERM CIRCUIT NO.
1 8 BRN4312-0 7
HERE 1 GRN0812-4
10 BLU3631-0 8
2 YEL0812-4
21 GRA3511-1 7
D 5 23 BRN4330-0 D
TERMINAL INFORMATION FOR: P114
25 GRA4584-2 P20-1193-1202G, BLACK, ( 2 CAVITIES )
ORIENT CONVOLUTE SO J119 SEE HARNESS VARIATION TABLE
THE SLIT IS ON THIS 27 BLU4381-0 LABEL: P114, J1939 V-CAN FOR OMISSION INFORMATION.
SIDE 29 YEL0852-3 2 1 TERM CIRCUIT NO.
37 GRN0852-3
38 VIO3141-0 1 GRN0812-0
P114 TERMINAL INFORMATION FOR: P119
42 GRN3141-0 2 YEL0812-0 P20-1040, BLACK, ( 2 CAVITIES )
56 53
43 RED3110-1 LABEL: P119, ETHER START SOLENOID
45 BLU3142-0 TERM CIRCUIT NO.
C 46 VIO3142-3 A GRA3123-0 C
47 YEL0812-4 B GRN3123-0
48 YEL0818-11
MATING VIEW 49 BLU3141-0
55 GRN0812-4
56 GRN0818-11
57 WHT3111-3
58 WHT3111-2
P101 59 WHT3111-1
B SEE DETAIL A
B
60 YEL3111-4
SHEET 2, ZONE J-6
61 YEL3111-3
FOR WIRE ROUTING
IN BACKSHELL 62 YEL3111-2
32 GRN4381-0

A A
DWG
SIZE
A0
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
 A COMPANY
Harness - Eng MX EPA '04 P92-5156 A 04
© 2009 PACCAR Inc – All Rights Reserved – The information contained in this drawing is proprietary to PACCAR. Reproduction, in whole or in part, by any means is strictly prohibited without prior written authorization from PACCAR Inc.

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

"START CTRL RLY TO STRT RLY"

"NAMUX POWER SUPPLY ( +5V )"
L L

"A / C COMPRESSOR CLUTCH"

"REMOTE THROTTLE SIGNAL"
USAGE NOTE:

"THROTTLE SENSE RETURN"

"THROTTLE SENSE SUPPLY"

"NAMUX ANALOG RETURN"
"BODY IGN POWER ( 10A )"
USE ON T8 / T6 MODELS WITH NAMUX 3

"THROTTLE SENSE POS"

"REMOTE PTO RESUME"
INSTRUMENTATION AND MX EPA '04 ENGINES

"CHECK ENGINE LAMP"

"IDLE VALIDATION SIG"

"IDLE VALIDATION SW"

WITH ETC-3 ENGINE CONTROLLER.

"ECU WAKE UP ( 5A )"

"STOP ENGINE LAMP"
"REMOTE PTO SET"

"J1939 V-CAN ( + )"

"J1939 V-CAN ( - )"

"OAT RETURN"

"OAT SENSE"

"OBD MIL"
P103
K DASH HARNESS P118 K
P103 ENGINE FAN SOLENOID
J118
A B 18 1
29 1 37 38 11 28 24 39 8 7 31 30 18 5 23 22 12 14 13 42 43 3 21 2 47 34 32 9 45 19 35 36 10 20 4 46 25 26 6
3
P118 GRA3191-0, 1.0mm^2 J118
4 ENGN FAN BREAKOUT

GRN4527-0, 0.8mm^2

BLU4527-0, 0.8mm^2
GRN4500-2, 0.8mm^2
ORN1229-2, 2.0mm^2

ORN3112-1, 0.8mm^2
GRA3512-0, 0.8mm^2

GRA3513-0, 0.8mm^2
YEL3191-0, 1.0mm^2

VIO4500-2, 0.8mm^2

BLU3144-0, 0.8mm^2

BRN4311-0, 0.8mm^2

BRN4312-0, 0.8mm^2
BLU3142-0, 0.8mm^2

BRN4330-0, 0.8mm^2
VIO3142-3, 0.8mm^2

GRA3912-1, 1.0mm^2
GRN3141-0, 0.8mm^2

BLU3141-0, 0.8mm^2
J J

VIO3141-0, 0.8mm^2
YEL0812-0, 0.75mm^2

GRN0812-0, 0.75mm^2
P107
P124 YEL7111-0, 2.0mm^2 B
P107
REMOTE PTO / THROTTLE
P124 WHT7111-0, 2.0mm^2 A AC COMPRESSOR CLUTCH
J124

"NAMUX POWER SUPPLY ( +5V )" 10 10 VIO4500-2, 0.8mm^2

P712
12 12 YEL3192-0, 0.8mm^2 B P712
I "NAMUX ANALOG RETURN" 3 3 GRN4500-2, 0.8mm^2 GRA3192-2, 0.8mm^2 A
A/C PRESSURE SWITCH ( ECU FAN CTL ) I
"BODY IGN POWER ( 10A )" 7 7 ORN1229-2, 2.0mm^2

2 P148
"REMOTE PTO SET" 2 GRA3512-0, 0.8mm^2
P114
2 1 7 "HUMIDITY SENSOR ECU RTN"
"REMOTE PTO RESUME" 1 1 GRA3513-0, 0.8mm^2 WHT3198-1, 0.8mm^2
2 1 3
6 6 WHT3215-0, 2.0mm^2 "VGT ACTUATOR GND"
J114 4
"REMOTE THROTTLE SIGNAL" 4 4 BLU3144-0, 0.8mm^2 BLK3216-1, 0.8mm^2 "FUEL METERING VLV RTN"
H 5 H
"PTO ON / OFF" 5 5 GRA3511-1, 0.8mm^2 GRA3216-1, 0.8mm^2 "FUEL METERING VALVE"
2
9 9 YEL3198-2, 2.0mm^2 "ENG ACT / SNSR PWR"
1
"ENG SYS POWER" 11 11 YEL3511-0, 2.0mm^2 YEL3198-1, 2.0mm^2 "VGT ACTUATOR PWR"
S18
6
"GROUND" 8 8 WHT1513-2, 2.0mm^2 P148
APPLICATION POWER

G J175 G
K

S06 P

F M F
"OAT RETURN" 6 GRN4527-0, 0.8mm^2
N
"OAT SENSE" 5 BLU4527-0, 0.8mm^2 WHT1513-3, 5.0mm^2
S07 D
YEL3116-0, 3.0mm^2 "ENGINE POWER ( 20A )"
J149 4
GRA3216-1, 0.8mm^2 H "FUEL METERING VALVE"
APPLICATION SIGNAL
3
BLK3216-1, 0.8mm^2 J "FUEL METERING VLV RTN"
"ETHER START SOLENOID GND" 2 GRN3123-0, 0.8mm^2
G
"ETHER START SOLENOID CONTROL" 1
E J149 GRN4381-0, 0.8mm^2 U "WIF RETURN" E
BLU4381-0, 0.8mm^2 V "WIF SENSE"

RED3110-1, 0.8mm^2 W "LPC BATT POWER ( 5A )"

GRA3112-0 , 0.8mm^2 T "ENG ECU RELAY"

GRA3511-1, 0.8mm^2

A A C
GRA3123-0, 0.8mm^2
P119
B B A
ETHER START SOLENOID GRN3123-0, 0.8mm^2
D P119 E D
J119 YEL3111-0, 3.0mm^2 "ENG ECU PWR ( 25A )"
S32
J168 R
GRN0818-9, 0.75mm^2 "J1939 A-CAN ( - )"
GRN0812-4, 0.75mm^2
YEL0812-4, 0.75mm^2

A S31
P168 A YEL3631-0, 0.8mm^2 S
YEL0818-9, 0.75mm^2 "J1939 A-CAN ( + )"
RAX RATIO HI / LOW SW B
GRN3141-0, 0.8mm^2

B BLU3631-0, 0.8mm^2
BLU3141-0, 0.8mm^2

VIO3141-0, 0.8mm^2

GRN0818-11, 0.75mm^2

B
YEL0818-11, 0.75mm^2

P168 S02
S03
GRN4381-0, 0.8mm^2

BLU4381-0, 0.8mm^2

GRA3112-0, 0.8mm^2
RED3110-1, 0.8mm^2

ORN3112-0, 0.8mm^2

J175
BRN4330-0, 0.8mm^2
BLU3631-0, 0.8mm^2

BRN4311-0, 0.8mm^2

BRN4312-0, 0.8mm^2

WHT3110-0, 0.8mm^2
GRA4584-2, 0.8mm^2

WHT3111-1, 2.0mm^2

WHT3111-2, 2.0mm^2

WHT3111-3, 2.0mm^2
GRA3192-2, 0.8mm^2
VIO3142-3, 0.8mm^2

YEL3111-4, 2.0mm^2

YEL3111-3, 2.0mm^2

YEL3111-2, 2.0mm^2

C C
BLU3142-0, 0.8mm^2

"J1939 HS-CAN ( + )" G YEL0852-3, 0.75mm^2 CHASSIS HARN

WHT1513-1, 13.0mm^2
"J1939 HS-CAN ( - )" F GRN0852-3, 0.75mm^2

"J1939 A-CAN ( - )" E GRN0818-6, 0.75mm^2

GRA3912-1, 1.0mm^2
"J1939 A-CAN ( + )" D YEL0818-6, 0.75mm^2

B 21 37 29 50 16 17 10 32 27 43 3 47 55 40 36 42 49 38 45 46 4 8 23 1 25 26 6 7 56 48 60 61 62 59 58 57
B P101
B
"MAN FAN SW/AC PRESS SW"
"PTO ON / OFF"

"J1939 HS-CAN ( - )"

"OBD MIL"
"IDLE VALIDATION SW"

"ECU WAKE UP"

"WIF RETURN"

"WIF SENSE"

"J1939 V-CAN ( + )"

"THROTTLE SENSE POS"

"STOP ENGINE LAMP"

"J1939 A-CAN ( - )"

"ENG ECU RELAY"

"IDLE VALIDATION SIG"

"CHECK ENGINE LAMP"

"CASE GND"

"J1939 A-CAN ( + )"

"ECU RETURN ( - )"

"ECU RETURN ( - )"

"J1939 V-CAN ( - )"
"J1939 HS-CAN ( + )"

"REAR AXLE HI/LO SIGNAL"

"LPC BATT POWER ( 5A )"

"ECU SUPPLY ( + )"

"ECU SUPPLY ( + )"

"ECU RETURN ( - )"

"ECU SUPPLY ( + )"
"THROTTLE SENSE RETURN"

"THROTTLE SENSE SUPPLY"

"CLUTCH SWITCH"

A
T133
H
P101
T121
J174 ENG ECU ( OEM ) "PORT J2"
ENGINE GROUND

J174
DATALOGGER HARNESS
T121
STARTER RELAY ( COIL )
A A
T133

DWG
SIZE
A0
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1