EMS machine user manual
EMS machine user manual
EMS machine user manual
The 100% limit muscle contraction of HIFEM technology can trigger a lot of lipolysis, Fatty
acids are broken down from triglyceric acid, and accumulated in large amounts in fat cells.
The fatty acid concentration is too high, which will cause fat cells to apoptosis and be
excreted from the body by normal metabolism within a few weeks. Therefore, HIFEM
beauty muscle instrument can strengthen and increase muscles while achieving the effect of
reducing fat.
1、It can set different muscle training modes.
2、180 radian handle design, more suitable for arm and thigh curve design, easy to operation.
3、Four treatment handles, dual channel control energy, support two or four handle synchronous
work; it can operate two persons or four persons at the same time, suitable for men and
women.
4、It’s safe and non-invasive, non-current, non-hyperthermia, and non-radiation, and no recovery
period.
5、No knife, no injection, no medicine, no exercise, no diet, Just Lying down can burn fat and
build muscle, and reshape the beauty of lines.
6、Saving time and effort, only lying down for 30 minutes = 30000 muscle contractions
(equivalent to 30000 belly rolls / squats)
7、It’s simple operation and bandage type. The operating head only needs to be placed on the
operating part of the guest, and it can be reinforced with a special equipment band, without
the need for a beautician to operate the instrument, which is convenient and simple.
8、It's non-invasive, and the process is easy and comfortable. Just lie down and experience it like
a muscle is sucked up.
9、During the treatment, there is only a feeling of muscle contraction, no pain and no sweat, and
there is no side effects on the body, just do it and go.
10、There are sufficient experimental studies to prove that the treatment effect is remarkable. It
only takes 4 treatments within two weeks, and every half an hour, you can see the effect of
reshaping the lines in the treatment site.
11、The cooling system of water circulation prevents the treatment head from generating high
temperature, which greatly improves the stability of energy output.
• Choosing a relaxed and professional way to build muscle and burn fat without harming
your health. Choice is more important than effort!
abdominal / hip treatment, equivalent to 30000 times of sit ups / squats), so that you can easily
It may not be normal to have "mother belly" after childbirth! As many as 60% of mothers have a
separation of rectus abdominis after delivery. As a result, the fetus has the opportunity to stretch
the abdominal muscles during the growth of the fetus. Loss of support will make the organs fall
down, resulting in postpartum abdominal relaxation and sagging, fat, protruding belly, and Lack
of abdominal strength, which is often accompanied by low back pain, lumbar muscle strain and
other problems
Once the rectus abdominis is separated, the traditional abdominal curling exercise will only
make the abdominal muscles more open. However, the suture of rectus abdominis through
cesarean section is not a good strategy because of its great trauma and slow recovery.
Only HIEMT brings non-invasive technology to postpartum women and solves the separation of
rectus abdominis for many mothers, The latest MRI and CT computed tomography medical
research confirmed that after the HIEMT treatment, the separation of rectus abdominis was
reduced by an average of 11%, while fat loss was reduced by 19% and muscle growth was 16%.
It is the perfect solution for mothers to lose weight and maintain health after delivery.
《Induction of adipocyte apoptosis:Safety and mechanism evaluation of non-invasive HIFEM
technology in pig model》
• The apoptotic level of adipocytes increased from 19% to 36% after a 30 minute treatment
• Blood analysis confirmed a rapid metabolic response after treatment as evidence of changes in
subcutaneous adipose tissue
•No security risks have been identified
《Decreased subcutaneous fat: Changes of subcutaneous fat thickness after HIFEM treatment》
Before 1 month
肌肉平均厚
The average The average
度增加
muscle 16%
thickness improvement
increased of rectus abdominis Before After Before After
by 16% was 11%
《MRI:Synchronize fat and muscle effects》
HIFEM Technical MRI assessment:Research on the safety and effectiveness of fat and muscle
treatment based on non-invasive abdominal shaping
• Step-type exercise plan, energy-converging frequency exercise, to provide gradual exercise for your
muscles.
① Stretching and warm-up: the rhythm is gentle to drive the muscles to stretch, so that the muscles warm up and promote
blood circulation.
②Deepen exercise: gradually accelerate the rhythm to exercise muscles, stimulate a large number of deep muscle fibers to
participate in the force.
③ Activate muscles: gradually speed up the rhythm and intensity, activate muscle fiber contraction and force, and regain
muscle vitality
④Strengthen muscle gain: Speed up the rhythm and perform powerful and intense muscle contraction exercises to stimulate
high-speed contraction of deep muscles.Improve muscle density and increase muscle strength.
⑤Strong fat burning: Gradually increase the load, make the resistance muscle contraction, enhance the microcirculation in
the body, and accelerate the burning of fat into energy consumption.
⑥Relief: slower rhythm drives muscle contraction and relaxes muscle fatigue.
• The composition of skeletal muscles can be divided into two categories, fast and slow muscle fibers.
Fast Twitch Fiber (White Muscle) Slow muscle fiber (red muscle)
• Fast-twitch fibers are characterized by fast contraction speed, high strength, short-term energy provided by anaerobic
metabolism, and no endurance.
• Slow muscle fibers are characterized by slow contraction speed, low strength, good use of oxygen, and endurance.
• The faster the exercise speed, the more white muscles are stimulated, and the slower the speed, the more red muscles are
stimulated
●Muscle motor neurons are controlled by the ●Using HIFEM technology penetrate into 8cm muscle
brain, and the intensity and amplitude of tissue, and using high-frequency contraction signal
muscle contraction are limited, only some directly launch motor neurons;
muscles can exercise. ●Up to 30,000 extreme muscle exercises in 30
●It is difficult to achieve muscle gain in a short minutes, surpassing ordinary exercises, causing
period of time many muscles to produce high-frequency
contractions.
EMS
• Most of the energy of the current is concentrated in the
surface layer, only a small part can reach the muscle;
• Feeling a slight tingling or contraction;
• It takes 40 treatments to produce a visible change
• The intensity of treatment cannot be increased due to the risk of pain and burns.
HIFEM VS EMS
(HIFEM) (EMS)
Electric current is passed directly
The electric field is generated in the
Treatment through the skin and need to
subcutaneous muscle tissue without
intensity contact the medium (gel pad).
contact with the medium.
Electrodes are usually disposable.
HIFEM has a great penetration depth, Most of the energy of the current is
covering the whole neural network and concentrated in the surface layer,
Penetrability
driving the contraction of the whole and only a small part reaches the
muscle layer. muscles.
Suitable for thin patients. The
Customer Due to the deep penetration, HIFEM suitable superficial current cannot reach the
type for all types of customers. muscles of patients with medium
fat layers.
Physiological The effects of fat apoptosis and "super Feeling a slight tingling or
response muscle exercise" are never achieved by contraction, equivalent to mild
physical exercise. physical exercise.
Course of Studies in the United States have shown It takes 40 treatments to produce a
treatment that four treatments are the best visible change
Fixed frequency treatment. There
Regularly changing the frequency to is no effect of removing waste
treatment
obtain effective stimulation and tissue products or increasing blood flow,
solutions
response. causing muscle fatigue and
limiting efficacy.
Treatment The intensity is low due to the risk
High-energy comfort treatment.
intensity of pain and burns.
There is obvious pain, the
The treatment is completely painless.
treatment activates the pain
Treatment HIFEM does not activate pain receptors
receptor. FDA warns of electric
risk and there is no risk of burns. The side
shock, burns, contusion, irritation,
effects are limited to muscle fatigue.
and pain.
1、Water injection
• In order to facilitate the transportation and transshipment of the equipment, the manufacturer shall
drains all the water in the equipment before transportation. Pure water must be injected before
the equipment is used. Note: Be sure to fill and release water in the shutdown state.
• There are labels on the back of the instrument, which are water inlet hole, overflow hole and
outlet hole according to the label. Water inlet method: Insert the valve connector into the
overflow hole;Then insert the funnel water pipe into the water inlet hole;Pour the pure
water(about 3500ml) from the funnel until there is water overflowing from the overflow hole,
After adding water,Then turn it on and run for 30 seconds to 1 minute; turn it off and add water
for the second time until water flows out from the overflow hole, indicating that the water is full.
Then press the spring catch above the overflow and inlet hole,You can pull out the valve
connector and water pipe.
2、Water exchange and drainage
• When using the equipment, remember that the water in the equipment and the handle must be
drained out during transportation
• In order to extend the service life of the equipment, it is recommended to change the water once a
month, and to ensure that the water quality in the instrument is good, to avoid the growth of
bacteria and prevent the waterway from being blocked; when the instrument is used frequently, it
is recommended to change the water once every 15 days before continuing to use it. .
• How to change the water? Draining water before changing water. Method of draining water:Insert
the valve connector into the outlet hole, and the water in the equipment will flow out automatically.
After the water is completely discharged, then press the spring catch above the outlet hole,You can
pull out the valve connector and water pipe. Method of adding water:Insert the valve connector
into the overflow hole;Then insert the funnel water pipe into the water inlet hole, and start adding
water until the water flows out from the overflow hole, indicating that the water is full.
3.How to drain the handle: Insert the two air nozzle connectors into the water drain holes of the
handle, and then raise the handle head up until the water is completely discharged, and then press
the buttons on both sides of the handle to pull out the air nozzle connector
4、Maintenance
• The instrument must use a plug with a grounding pin, and ensure that the power socket of the
instrument is well grounded.
• Ensuring that the power supply is stable and adaptable. If the local power supply voltage is
unstable, it is recommended that the user add a regulated power supply with matching power.
Special reminder: The power cord of the socket is required to be more than 1.5 square meters.
• When the device is in use, keep away from the wall and keep a 30cm space around the device for
heat dissipation.
• After each treatment, wet the towel with normal saline to clean the accessories.
• Do not use alcohol or corrosive solvents to clean the host and handle to avoid damage.
• The working handle should be handled gently, and it is strictly forbidden to drop it to avoid
damage.
• In the process of use, the working handle should avoid extreme bending and damage.
• Do not place the instrument in an environment with high temperature, humidity, dust, and direct
sunlight. The instrument should be placed in a dry, cool and ventilated room with a temperature
of 5 to 40°C and a humidity of no more than 80%.
• When the instrument is not in use, please turn off the power, then unplug the power plug and
place the various accessories of the instrument. If possible, cover the instrument with a dust
cover.
• If it is not used for a long time or when it is being transported, The water should be drained clean.
• It is strictly forbidden to disassemble and modify equipment without authorization.
• If there is any fault in the equipment, it should be shut down immediately and please contact us.
1 、 Warm tips! For the first time, it must be filled with water before starting up. Never work
without water!
2、Installation: align the handle with the handle socket on the back of the device and place it on
the rack; add water to the device. After adding water, insert the power cord into the socket on the
back of the device, turn on the power, turn on the power switch, and run for 30 seconds to 1
minute Then turn off the machine and add water for the second time. After the second time of
water addition, turn on the power again, turn on the power switch, and the device will start up
immediately.
Press and hold the buttons on both sides to pull out straight, do not
shake.
3、Accessories
Figure 4
5、Manual working interface:Setting intensity(Figure 5)
(Figure 4)/(Figure 5)I introduction of manual working interface:
• Setting the frequency F1-F3.click【+】and【-】to adjust the output frequency,the range as
below:
【F1】:The intensity range is 3HZ (weak) to 150Hz (strong);
【F2】:The intensity range is 3HZ (weak) to 150Hz (strong);
【F3】:The intensity range is 1HZ (weak) to 12Hz (strong);
Before operation, set the frequency parameters according to the required frequency. Each
frequency is 6 minutes. During operation, the F1, F2, and F3 frequencies will cycle in turn.
The recommended parameters are 30Hz-40Hz for F1, 80Hz-100Hz for F2,
and 0Hz or 5Hz for F3.
• Setting the intensity, rang from 8% (weak) to 100% (strong)
【Intensity A B】:A and B handle intensity,click【-】and【+】to adjust.
【Intensity C D】:C and D handle intensity,click【-】and【+】to adjust.
Set intensity before operation ,The treatment starts from low intensity, and should be gradually
increased according to the patient's tolerance.
• Setting the working time. The default working time of sysstem is 30 minutes,click【+】and
【-】to adjust. The time range can be adjusted from 1 to 30 minutes, and the operation of each
part is about 30 minutes.
• Click“ ”to start,If you need to pause,please click“ ”。click“ ”to return to the previous
interface.
•Interface alarm prompt:
* Start up
E1 E2
The cooling water is not enough,please add The handle is not inserted properly,please
water and restart the host before use. check the handle.
E3
The cooling water temperature is too
high,please rest for a while before use.
Note: If the system displays an alarm code, please shut down and restart it, and solve the
problem according to the corresponding alarm code. If the problem still exists after solving the
above method, please contact the manufacturer or agent service provider.
The position of the operation must be the same as the selected part of the interface
1、Don’t operate head, neck/carotid artery, wealth bag position,or near the thoracic gallery.
2、The two handles cannot work against each other.
3、The healer should not carry any metal objects.
4、Don't be full during treatment, and treat at least 1 hour after meals.
5、The operation site and treatment probe should be dry without water.
6、The operating energy varies from person to person and increases gradually from low energy.
7、The total operating time of a day does not exceed 1.5 hours, and one part does not exceed 1
hour.
8、Do not put any electronic products or metal objects on the instrument during operation.
9、Don’t eat or enter water during operation
10、After the end of the operation, try to eat again after 1 hour (drink more water and eat food
with high protein content).
11、Those people with the following conditions cannot receive treatment:
▲The project should avoid menstruation, pregnancy and lactation;
▲Those patients with heart disease, hypertension, thyroid, malignant tumor, renal failure,
epilepsy and muscle strain should be used cautiously;
▲Those people with metal or electronic implants (metal contraceptive ring, cardiac pacemaker,
cardiac defibrillator, nerve stimulator, drug pump and stent) should be used cautiously;
▲Those patients with thrombophlebitis, cerebrovascular disease (stroke patients), brain injury
or with brain surgery should be used cautiously.
2、Is there a difference in the effect of abdominal treatment with one or two treatment
heads? How should we choose?
A: It is recommended that all patients use two treatment heads at the same time. Both treatment
heads must be in full contact with the skin, and not hover sideways or extend beyond the
treatment area. This will ensure that all abdominal muscles are treated and activated. Using one
treatment head at a time is only recommended for patients with small care sites. Both therapies
are equally effective.
6、How long will a course of treatment take? How long will it take effect?
A: 4 times for a course of treatment, interval 2-3 days to do once, generally open a card set 6-8
courses of treatment, which can get good results. The best results are in the 2-4 weeks after the
treatment. To break down fat and increase muscle mass, patients need to be patient. Usually after
4-6 treatments, muscle mass increases by approximately 16% and fat can be reduced by 19%.
7、How long will the effect last?
A:The effect can be maintained for one year after 6 courses. But some people may need additional
treatment to achieve the best results. If you have a course of treatment every 2-3 months, you can
maintain a better and best condition. At the same time, customers can visit the store multiple times.