PRAGATI ENGINEERING COLLEGE

(Autonomous)
(Approved by AICTE, Permanently Affiliated to JNTUK Kakinada & Accredited by NBA)
ADB Road, Surampalem – 533 437, Near Peddapuram, E.G.Dist., A.P.
Ph: (08852) – 252233, 252234, www.pragati.ac.in
DEPARTMENT OF MECHANICAL ENGINEERING

ASSIGNMENT QUESTIONS

UNIT-I

LEVEL I
S.
Question BTL
No.
1 Divide an 80 mm long straight line into seven equal parts. K2
2 Draw regular pentagon and a heptagon on a common edge of side 30mm. K2
3 Draw a hexagon and an octagon on a common edge of side 40mm. K2

LEVEL II
S.
Question BTL
No.
A fixed point is 75 mm from a fixed straight line. Draw the locus of a point P
1 moving such a way that its distance from the fixed straight line is twice its K3
distance from the fixed point; Name the curve.
Construct a diagonal scale of R.F=1/32 showing yards, feet and inches to
2 K3
measure up to 4 yards. Show 1 yard 2 feet 7 inches on it.
Construct a vernier scale of 1:40 to read metres, decimetres and centimetres and
3 K3
long enough to measure up to 6 m. Mark a distance of 4.76 m on it.

LEVEL III
S.
Question BTL
No.
Two points Q and S lie on a straight line through the centre C of a circle of 50
1 mm diameter, rolling along a fixed straight line. Draw and name the curves K3
traced out by the points Q and S during one revolution of the circle.
Draw a path of the end of string when it is wound on a circle of 40 mm diameter
2 K3
without slipping. The length of the string is 150 mm long. Name the curve.
A car is running at a speed of 50 km/hour. Construct a diagonal scale to show 1
3 km by 3 cm and to measure upto 6 km. Mark also on the scale the distance K3
covered by the car in 5 minutes 28 seconds.

*K1: Remember, K2: Understand, K3: Apply, K4: Analyze, K5: Evaluate, K6: Create.
 ASSIGNMENT 1 ANSWERS

Level I

1.

2.
3.

Level II

1.
2.
RF = 1/32
Maximum Length = 4 Yards
Length of the scale = (1/32) * 4yards = (1/32) * 4 * 3feet = (1/32) * 4 * 3 * 12inches = 4.5inches

3.
RF = 1:40
Maximum Length = 6m
Length of the scale = (1/40) * 6m = (1/40) * 6 * 100cm = 15cm

Level III

1.

OR
2.
3.

RF = 3cm/1km
Maximum Length = 6km
Length of the scale = (3cm/1km) * 6km = 18cm
As we have to Mark on the scale the distance covered by the car in 5 minutes 28 seconds.
Convert the KM scale in terms of minutes and seconds with the relation given when the car is
running at a speed of 50 km/hour.
*50km/hour = 5km/6min i.e., 6km in 7.2min
 PRAGATI ENGINEERING COLLEGE
(Autonomous)
(Approved by AICTE, Permanently Affiliated to JNTUK Kakinada & Accredited by NBA)
ADB Road, Surampalem – 533 437, Near Peddapuram, E.G.Dist., AP.
Ph: (08852) – 252233, 252234, www.pragati.ac.in
DEPARTMENT OF MECHANICAL ENGINEERING
ASSIGNMENT QUESTIONS
UNIT-II
LEVEL I
S. No. Question BTL
Draw the projections of the following points on the same ground line,
keeping the Projectors 25mm apart.
1 K2
i. A, in the HP and 20 mm behind the VP.
ii. B, 40mm above the HP. and 25mm in front of the VP.
Two pegs fixed on a wall are 4.5 meters apart. The distance between the
pegs measured parallel to the floor is 3.6metres. If one peg is 1.5metres
2 K2
above the floor, find the height of the second peg and the inclination of
the line joining the two pegs, with the floor.
(a) A line of 100 mm long is parallel to 30 mm above HP. Its two ends
are 25 mm and 50 mm in front of VP respectively. Find its inclination
with VP.
3 K2
(b)A line EF 60mm long is in VP and inclined to HP. The top view
measures 45mm. The end E is 15mm above HP. Find the inclination
with HP.

LEVEL II
S. No. Question BTL
The end A of a line AB is in the HP and 25mm behind the VP. The end
B is in the VP and 50mm above the HP. The distance between the end
1 K3
projectors is 75mm. Draw the projections of AB and determine its true
length, inclinations with the two planes.
A semi-circular plane of diameter 70 mm has its straight edge on the HP
2 K3
and inclined at 450 to the VP. Draw the projection of the plane.
A regular hexagon of side 20 mm has one of its sides inclined at 300 to
3 VP. Its surface makes an angle of 600 with the ground. Draw its K3
projections.

LEVEL III
S. No. Question BTL
A line PQ has its end P, 10 mm above the HP and 20 mm in front of the
VP. The end Q is 85 mm in front of the VP. The front view of the line
1 K3
measures 75 mm. The distance between the end projectors is 50 mm.
Draw the projections of the line and find its true length.
A 600 set square of 145 mm longest side is so kept that the longest side is
2 in the HP making an angle of 300 with the VP and the set square itself K3
inclined at 450 to the HP. Draw the projections of the set square.
A circular lamina of 60 mm diameter rests on HP on a point 1 on the
circumference. The lamina is inclined to HP such that the top view of it
3 is an ellipse of minor axis 35 mm. The top view of the diameter through K3
the point 1 makes an angle of 450 with VP. Draw the projections and
determine the angle made by the lamina with HP.
*K1: Remember, K2: Understand, K3: Apply, K4: Analyze, K5: Evaluate, K6: Create.
 ASSIGNMENT 2 ANSWERS

Level I

1.

2.

3.
Level II

1.

2.
3.

Level III

1.
2.

3.
 PRAGATI ENGINEERING COLLEGE
(Autonomous)
(Approved by AICTE, Permanently Affiliated to JNTUK Kakinada & Accredited by NBA)
ADB Road, Surampalem – 533 437, Near Peddapuram, E.G.Dist., A.P.
Ph: (08852) – 252233, 252234, www.pragati.ac.in
DEPARTMENT OF MECHANICAL ENGINEERING
ASSIGNMENT QUESTIONS
UNIT-III
LEVEL I
S. No. Question BTL
A hexagonal pyramid of base side 30mm and axis 60mm is lying on a
1 K2
slant edge on the HP with the axis parallel to VP. Draw its projections.
A pentagonal prism, base 25mm side and axis 50mm long, has an edge
2 of its base on the ground. Its axis is inclined at 300 to the ground and K2
parallel to VP. Draw its projections.
Draw the projections of a hexagonal prism, base 25mm side and axis
3 K2
50mm long, resting on one of its rectangular faces on the ground.

LEVEL II
S. No. Question BTL
A cone of diameter of base 60mm and axis length equal to 120mm rests
1 on a point of its periphery of the base on HP such that its axis is inclined K3
at an angle of 350 with the HP. Draw its projection
A square pyramid, base 40mm side and axis 90mm long, has a triangular
2 K3
face makes an angle of 450 with the VP. Draw its projections.
A hexagonal pyramid, base 25mm side and axis 50mm long, has an edge
3 of its base on the ground. Its axis is inclined at 300 to the ground and K3
parallel to VP. Draw its projections.

LEVEL III
S. No. Question BTL
A hexagonal prism, base 35mm side and height 50mm has a hole of
40mm diameter drilled centrally through its ends. Draw its projections
1 K3
when it is resting on one of its corners on the HP with its axis inclined
at 600 to the HP and two of its faces parallel to the VP.
A pentagonal prism, base side 40mm and axis 70mm has a centrally
drilled square hole of side 20 mm. Draw its projections when the prism
2 K3
is resting on an edge of its base on the HP and the axis inclined at 600 to
the HP and parallel to the VP.
A pentagonal pyramid has height 60mm and the side of a base 30mm.
3 The base of the pyramid makes an angle of 450 with the VP. Draw its K3
projections.
*K1: Remember, K2: Understand, K3: Apply, K4: Analyze, K5: Evaluate, K6: Create.
 ASSIGNMENT 3 ANSWERS

Level I

1.

2.
3.

Level II

1.
2.

3.
Level III

1.

2.
3.
 PRAGATI ENGINEERING COLLEGE
(Autonomous)
(Approved by AICTE, Permanently Affiliated to JNTUK Kakinada & Accredited by NBA)
ADB Road, Surampalem – 533 437, Near Peddapuram, E.G.Dist., A.P.
Ph: (08852) – 252233, 252234, www.pragati.ac.in
DEPARTMENT OF MECHANICAL ENGINEERING
ASSIGNMENT QUESTIONS
UNIT-IV
LEVEL I
S. No. Question BTL
A triangular prism with a base side of 45 mm and an axis length of 70 mm has an
edge of base on the HP. A horizontal section plane passing through the midpoints of
1 K3
the longest edges of the rectangular face cuts the prism. Draw front view and sectional
top view.
A cube of side 35 mm rests in the VP with one of its sides inclined at 450 to the HP.
2 A sectional plane parallel to HP and inclined at 300 to VP cuts the solid at a distance K3
of 15 mm in front of the VP. Draw the sectional front view and top view.
A cone of base diameter 40 mm and slant height 60 mm is kept on the ground on its
3 base. A sectional plane inclined at 45° to the HP cuts the cone through the midpoint K3
of the axis. Draw the development.

LEVEL II
S. No. Question BTL
A cone of diameter 60 mm and height 70 mm is resting on ground on its base. It is cut
by a section plane perpendicular to V.P. inclined at 450 to H.P. and cutting the axis at
1 K3
a point 40 mm from the bottom. Draw the front view, sectional top view and true
shape.
A hexagonal prism of side of base 20 mm and length of axis 50 mm is kept on the
ground on its base such that two opposite sides of the base are parallel to the VP. It is
2 K3
cut by a plane inclined at 45° to the HP and passing through one of the top corners of
the prism. Draw the development of the cut prism.
A cube of 70 mm long edges has its vertical faces equally inclined to the HP. It is cut
3 by a sectional plane at an angle of 550 to the HP bisecting the axis. Draw FV, sectional K3
TV and development of the section.

LEVEL III
S. No. Question BTL
A pentagonal prism with a 25 mm base side and 70 mm height is resting on its base
on the HP with a side of base inclined at 40° to the VP. A sectional plane inclined at
1 K3
65° to the HP and passing through the midpoint of the axis cuts the prism. Draw front
view, sectional top view and the true shape of the section.
A hexagonal pyramid with side of base 30 mm and height 75 mm stands with its base
on HP and an edge of the base parallel to VP. It is cut by a plane perpendicular to VP,
2 K3
inclined at 45° to HP and passing through the mid-point of the axis. Draw the
sectioned top view and develop the lateral surface of the truncated pyramid.
A cylinder with a 55 mm base diameter and a 95 mm long axis, stands vertically on
the ground. It is cut by an inclined plane such that the true shape of the section is an
3 K3
ellipse with major axis of 80 mm. Draw its FV, sectional TV and the true shape of the
section. Determine the inclination of the section plane with the HP.
*K1: Remember, K2: Understand, K3: Apply, K4: Analyze, K5: Evaluate, K6: Create.
 ASSIGNMENT 4 ANSWERS

Level I

1.

2.
3.

Level II

1.
2.

3.
Level III

1.

2.
3.
 PRAGATI ENGINEERING COLLEGE
(Autonomous)
(Approved by AICTE, Permanently Affiliated to JNTUK Kakinada & Accredited by NBA)
ADB Road, Surampalem – 533 437, Near Peddapuram, E.G.Dist., A.P.
Ph: (08852) – 252233, 252234, www.pragati.ac.in
DEPARTMENT OF MECHANICAL ENGINEERING
ASSIGNMENT QUESTIONS
UNIT-V
LEVEL I
S. No. Question BTL
Draw the three orthographic views of the object shown in figure. All
dimensions are in mm.

1 K3

Draw the isometric projection of the object from the views shown in
figure below. All dimensions are in mm.

2 K3

Draw the front view, top view and side view of the figure.

3 K3
 PRAGATI ENGINEERING COLLEGE
(Approved by AICTE, Permanently Affiliated to JNTUK Kakinada)
ADB Road, Surampalem – 533 437, Near Peddapuram, E.G.Dist., A.P.
Ph: (08852) – 252233, 252234, www.pragati.ac.in
DEPARTMENT OF MECHANICAL ENGINEERING

LEVEL II
S. No. Question BTL
Draw the following views of the block shown in figure below. (i) Front
View (ii) Top View (iii) Side View

1 K3

Draw the isometric view of the orthographic projection given below. All
dimensions are in mm.

2 K3

Draw the isometric view of the following Figure. All dimensions are in
mm.

3 K3
 PRAGATI ENGINEERING COLLEGE
(Approved by AICTE, Permanently Affiliated to JNTUK Kakinada)
ADB Road, Surampalem – 533 437, Near Peddapuram, E.G.Dist., A.P.
Ph: (08852) – 252233, 252234, www.pragati.ac.in
DEPARTMENT OF MECHANICAL ENGINEERING

LEVEL III
S. No. Question BTL
Draw (i) Front View (ii) Top View (iii) Side View for the below figure.
(All dimensions are in mm).

1 K3

Draw the isometric views for the below figure: (All dimensions are in
mm)

2 K3

Draw the front view and top view for the given figure.

3 K3

*K1: Remember, K2: Understand, K3: Apply, K4: Analyze, K5: Evaluate, K6: Create.
 ASSIGNMENT 5 ANSWERS

Level I

1.

2.
3.

Level II

1.
2.

3.
Level III

1.

2.
3.