Scribd Logo
Upload

Welcome to Scribd!

  • 2 views

    Firewerx - Calcium Silicate Board - TDS

    Uploaded by

    Phillips Bokkie

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Firewerx - Calcium Silicate Board - TDS

    Uploaded by

    Phillips Bokkie
    2 views3 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    2 views3 pages

    Firewerx - Calcium Silicate Board - TDS

    Uploaded by

    Phillips Bokkie

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    2 HR FIRE RATED CS BOARD DATA SHEET

    PRODUCT INTRODUCTION
    A smooth asbestos free Fire board with good thermal conductivity, tested and approved by South African authorities.
    FIRE BOARD CS has the following features:

     Light, thin – easy to carry, move and process.


     Moisture resistant - If the board gets wet, air-drying to remove the water will restore all the properties of the board.
     Flexibility – FIRE BOARD CS is more rigid than plywood.
     Fire Rated – Non Combustible
     Non Toxic under Fire
     Resistant to climatic conditions and moisture
     Rot Proof, Termite Resistant and Fungus Resistant
     Dimensionally Stable
     Trafficable and hard wearing, stability dependent on substrate fixed to
     Good Thermal Properties
     Easy to work and fix.
     Safe to work with, containing no hazardous materials and 100% asbestos free.
     Smooth surface for ease of finishing

    APPLICATIONS

     Structural Steel
     Ceilings, roofs and floors
     Partitions and external walls
     Ventilation and smoke extraction ducts
     Electrical & mechanical services enclosures
     Fire resistant glazing
     Tunnel fire protection and concrete upgrading
     Smoke barriers, access hatch and panels

    In the case of Fireboard CS board, the longitudinal direction is identical with the direction of manufacture. In
    Order to calculate permissible loading, application of the following values is recommended:

    FLEXION>/250
    BEARING SAFETY FACTOR>3

    In the following work sheets, certain makes of screws may be specified as being preferential in order to ensure a certain
    level of quality. The properties in all tables are mean values gives for guidance only. If certain properties are critical for a
    particular reason it is advisable to consult Firewerx.
    GENERAL TECHNICAL DATA

    Panel Size 1220 x 2440 x 9mm


    Neutral Designation CS Board
    Material class Non-combustible. according to DIN 4102:
    Part 1, BS 476: Part4 and AS 1530: Part 1
    Surface spread of flame Class 1 to BS 476: Part 7 and AS 1530: Part
    3
    Building regulations classifications Class 0
    Nominal dry density ( average ) 1500
    Alkalinity ( approx. ) 12
    Thermal conductivity ( approx ) 0.175
    Coefficient of expansion ( 20-600C) -6.4x10`6
    Diffusion resistance factor ( approx ) 20
    Nominal Moisture content ( air-dried )% 5-10
    Water absorption capacity ( average )g/cm 0.5
    Expansion under water, 100% saturation 0.5
    (maximum )
    Thickness tolerance of standards boards mm +- 0.5
    Length x Width tolerance of standards boards +-5
    Surface condition Front face smooth, back dimpled
    Modulus of elasticity E longitudinal N/mm² 3200
    Transverse N/mm² 2500
    Flexural Strength longitudinal N/mm² 10
    Transverse N/mm² 5.5
    Tensile strength longitudinal N/mm² 5
    Transverse N/mm² 4
    Compressive Strength N/mm² 8

    SCREW DRAW – OUT RESISTANCE


    Designation & Arrangement Screwed Depth Draw-out resistance
    Dimensions ( mm ) ( mm )

    Quick-fix screws in board face 20 -


    3.9 x 55 in board edge 20 -
    Quick-fix in board edge 30 -
    3.9 x 55 in board face 15 624
    Timber construction
    Screws 4.2 x 45( Hi-Low ) in board face 15 550
    Quick fix screws in board face 15 584
    4.0 x 40
    Screw inserts (Type B 3815in board face 15 350
    Rampa

    NOTICE FOR INSTALLATIONS

     FIRE BOARD CS can be worked using normal wood working cutting equipment.
     Nailing - A pneumatic gun can be used for nailing, but always ensure that the press penal at the gun head is
    adjusted. The use of stainless steel staples is recommended. For ceiling work, we suggest the use of 10 mm wide
    staples to increase the holding strength. For wall panel or other application, 4 mm wide staple is acceptable.
     Screw fixing- the use of 32mm ceiling screws is recommended
     Although not recommended, care should be taken when countersinking screws, as they might pull through.
     For fire rated application, screws must be covered with at least 1000µ Intumescent mastic which can then be
    skimmed with Cretestone or Rhino Lite.
     For skim finishing, ensure surface is dust and oil free, apply sufficient bonding agent, as per skim product
    specification.
     Ensure at least 10mm expansion gap around perimeter, to be filled with fire rated mastic
     Note should be taken of which side to expose, as the smooth side is for painting, and the textured side is for
    skimming or tiling.
    SAFE HANDLING INFORMATION
    The product is stable under normal conditions of storage. Individual board should be stacked and handled
    carefully to avoid damage to the board. FIRE BOARD CS boards should be lifted from a stack by sliding it
    sideway and carrying it by the long edges with arms spread apart to give even support of the board. Keep
    materials dry and store in dry and covered place. If the sheets should become wet, allow drying thoroughly before
    fixing is commenced.

    STORAGE AND TRANSPORT:


    FIRE BOARD CS is supplied in sheets on wooden pallets to permit handling by forklift truck. During storage, boards
    should be place on top of the battens / supports which are laid flat and equally spaced at not more than 400 mm
    intervals on solid level ground. Do not store boards on edge or lean upright for long periods. Each pallet should be
    covered and well protected indoors. No special transport equipment needed.
    1. Lying on Smooth Flat Surface 2. Timber battens ≦ 400 mm intervals to provide flat
    surface

    3. Insufficient timber batten supports do not provide smooth flat surface

    FIREWERX -- PASSIVE FIRE PROTECTION SPECIALISTS


    Suppliers and installers of all major brands of passive fire protection materials
    Unit 6&7 Beacon Business Park
    Marinus Road
    Milnerton
    Cape Town
    021-5511039
    [email protected]

    You might also like