FusionModule App User Manual (FusionModule2000) (2)

FusionModule App
User Manual (FusionModule2000)
Issue 01
Date 2024-01-05
HUAWEI DIGITAL POWER TECHNOLOGIES CO., LTD.

Copyright © Huawei Digital Power Technologies Co., Ltd. 2024. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Digital Power Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are the property of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei
Digital Power Technologies Co., Ltd. and the customer. All or part of the products, services and features
described in this document may not be within the purchase scope or the usage scope. Unless otherwise
specified in the contract, all statements, information, and recommendations in this document are
provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Digital Power Technologies Co., Ltd.

Address: Huawei Digital Power Antuoshan Headquarters
Futian, Shenzhen 518043
People's Republic of China
Website: https://digitalpower.huawei.com
Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. i

FusionModule App
User Manual (FusionModule2000) About This Document
About This Document
Purpose
This document describes the functions of the FusionModule app and provides
solutions to common faults.
Intended Audience
The document is intended for:
● Commissioning engineers
● Maintenance engineers
● Technical support engineers
Symbol Conventions
The symbols that may be found in this manual are defined as follows.
Symbol Description
Indicates a hazard with a high level of risk which, if not

avoided, will result in death or serious injury.
Indicates a hazard with a medium level of risk which, if not

avoided, could result in death or serious injury.
Indicates a hazard with a low level of risk which, if not

avoided, could result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not

avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to personal
injury.
Supplements the important information in the main text.

NOTE is used to address information not related to personal
injury, equipment damage, or environment deterioration.
Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. ii

FusionModule App
User Manual (FusionModule2000) About This Document
Change History
Issue Date Description
01 2024-01-05 This is the first official release.
Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. iii
FusionModule App
User Manual (FusionModule2000) Contents
Contents
About This Document................................................................................................................ ii

1 PAD Operation Guide............................................................................................................. 1
1.1 Feature Overview.................................................................................................................................................................... 1
1.2 User Guide................................................................................................................................................................................. 6
1.2.1 Downloading and Installing the App............................................................................................................................ 6
1.2.2 Logging In to the App........................................................................................................................................................ 8
1.2.2.1 Preparations for Login.................................................................................................................................................... 8
1.2.2.2 Logging In to the App Using the Account and Password...................................................................................9
1.2.2.3 Logging In to the App Through Facial Recognition..............................................................................................9
1.2.2.3.1 Recording Facial Information................................................................................................................................. 10
1.2.2.3.2 (Optional) Enabling Default Facial Recognition Login..................................................................................10
1.2.2.3.3 Logging In to the App Through Facial Recognition........................................................................................11
1.2.3 Opening the Access Control System Using Facial Recognition......................................................................... 11
1.2.4 Monitoring Device............................................................................................................................................................. 12
1.2.4.1 Turning On/Off Lights.................................................................................................................................................. 12
1.2.4.2 Opening Scuttles............................................................................................................................................................ 13
1.2.4.3 Opening Doors................................................................................................................................................................ 14
1.2.4.4 Power-On/Off Devices.................................................................................................................................................. 15
1.2.4.5 Setting Parameters for the Busway......................................................................................................................... 16
1.2.5 Maintaining Devices......................................................................................................................................................... 16
1.2.5.1 Adjusting the Device Layout...................................................................................................................................... 16
1.2.5.2 Upgrading Device Software........................................................................................................................................ 17
1.2.5.3 Exporting System Data.................................................................................................................................................18
1.2.5.4 Configuring Device Data............................................................................................................................................. 19
1.2.5.5 Synchronizing Device Parameters............................................................................................................................ 19
1.2.6 Viewing Data.......................................................................................................................................................................20
1.2.6.1 Viewing Performance Data......................................................................................................................................... 20
1.2.6.2 Viewing Operation Logs.............................................................................................................................................. 21
1.2.6.3 Viewing Access Control Events.................................................................................................................................. 21
1.2.6.4 Viewing Asset Details................................................................................................................................................... 21
1.2.6.5 Querying the Device Version Information............................................................................................................. 22
1.2.6.6 Viewing Network Parameters.................................................................................................................................... 22
1.2.7 Setting Parameters............................................................................................................................................................22
Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. iv

FusionModule App
1.2.7.1 Setting the PAD Power Control Policy.................................................................................................................... 22

1.2.7.2 Enabling the Permission to Control Smart Cooling Devices........................................................................... 23
1.2.7.3 Setting the Smoke Sensor Icon Display Policy..................................................................................................... 23
1.2.7.4 Enabling the iCooling Function................................................................................................................................. 24
1.2.7.5 Setting the Home Screen Display Policy................................................................................................................ 24
2 Smart Screen Operation Guide.......................................................................................... 25

2.1 Feature Overview.................................................................................................................................................................. 25
2.2 User Guide............................................................................................................................................................................... 28
2.2.1 (Optional) Setting the Language of the Smart Screen........................................................................................ 28
2.2.2 Downloading and Installing the App..........................................................................................................................29
2.2.3 Logging In to the App...................................................................................................................................................... 30
2.2.3.1 Preparations for Login.................................................................................................................................................. 30
2.2.3.1.1 Setting the Smart Screen IP Address................................................................................................................... 30
2.2.3.1.2 Setting the Communication IP Address (Smart Screen Exclusively Used by a Single Module)...... 31
2.2.3.1.3 Setting the Communication IP Address (Smart Screen Shared by Multiple Modules)...................... 32
2.2.3.1.4 (Optional) Setting Greetings.................................................................................................................................. 35
2.2.3.2 Logging In to the App Using the Account and Password................................................................................ 36
2.2.3.3 Logging In to the App Through Facial Recognition........................................................................................... 37
2.2.3.3.1 Recording Facial Information................................................................................................................................. 37
2.2.3.3.2 (Optional) Enabling Default Facial Recognition Login..................................................................................40
2.2.3.3.3 Logging In to the App Through Facial Recognition........................................................................................41
2.2.4 Switching Smart Modules............................................................................................................................................... 42
2.2.5 Monitoring Device............................................................................................................................................................. 43
2.2.5.1 Turning On/Off Lights.................................................................................................................................................. 43
2.2.5.2 Opening Scuttles............................................................................................................................................................ 44
2.2.5.3 Opening Doors................................................................................................................................................................ 44
2.2.5.4 Unlocking.......................................................................................................................................................................... 45
2.2.5.5 Power-On/Off Devices.................................................................................................................................................. 45
2.2.5.6 Setting Parameters for the Busway......................................................................................................................... 46
2.2.6 Maintaining Devices......................................................................................................................................................... 46
2.2.6.1 Adjusting the Device Layout...................................................................................................................................... 46
2.2.6.2 Upgrading Device Software........................................................................................................................................ 47
2.2.6.3 Exporting System Data.................................................................................................................................................48
2.2.6.4 Configuring Device Data............................................................................................................................................. 49
2.2.6.5 Synchronizing Device Parameters............................................................................................................................ 50
2.2.7 Viewing Data.......................................................................................................................................................................51
2.2.7.1 Viewing Performance Data......................................................................................................................................... 51
2.2.7.2 Viewing Asset and Version Information................................................................................................................. 52
2.2.7.3 Viewing Logs and Access Control Information.................................................................................................... 52
2.2.7.4 Viewing Energy Efficiency Information...................................................................................................................53
2.2.8 Parameter Settings............................................................................................................................................................53
2.2.8.1 Enabling the Permission to Control Smart Cooling Devices........................................................................... 53
Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. v

FusionModule App
2.2.8.2 Enabling the iCooling Function................................................................................................................................. 55

2.2.8.3 Setting the Display Policy of Cards on the Home Screen................................................................................ 57
2.2.8.4 Setting the Home Screen Display Policy................................................................................................................ 59
2.2.8.5 Setting the Policy for Displaying Performance Data......................................................................................... 61
2.2.8.6 Setting the Communication IP Address..................................................................................................................63
2.2.8.7 Setting Greetings............................................................................................................................................................ 65
2.2.8.8 Setting the Big Screen Location................................................................................................................................ 67
3 FAQs..........................................................................................................................................70
3.1 What Do I Do If Login Fails?............................................................................................................................................. 70
3.2 What Do I Do If the Power Distribution View Does Not Display the Circuit Diagram?...............................71
3.3 What Do I Do If the U Space Proportion Is Not Displayed on the App?...........................................................72
3.4 What Do I Do If a Smoke Sensor or Water Sensor Is Not Displayed on the App?........................................ 72
A Acronyms and Abbreviations............................................................................................. 73
Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. vi

FusionModule App
User Manual (FusionModule2000) 1 PAD Operation Guide
1 PAD Operation Guide
1.1 Feature Overview

This section describes the functions of the FusionModule app.
Home
● Home: Displays the smart module layout information, including the power,
cooling capacity, space, resources, energy efficiency, environment, and alarm
overview.
Figure 1-1 Home
● Resource: Displays resource information such as the power, cooling capacity,

and space of the entire smart module.
Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. 1

FusionModule App
Figure 1-2 Resource
● Energy: Displays the energy efficiency information of the cabinet, including

the energy efficiency curve and accumulated power consumption.
Figure 1-3 Energy
● Environment: Displays the cabinet environment information and detailed

information about each module in the cabinet. You can control devices such
as doors, skylights, and lighting.
Figure 1-4 Environment
● Active Alarms: Displays the statistics and list of active alarms of the current
device. You can acknowledge and clear active alarms.

FusionModule App
Figure 1-5 Active Alarms
● Historical Alarms: Displays the list of all handled alarms. You can sort alarms
by alarm generation time or alarm severity, and filter alarms by alarm
generation time or alarm severity.
Figure 1-6 Historical Alarms
iPower
iPower: Displays the power distribution link diagram of the smart module. You
can view the device information and parameters of power distribution devices.

FusionModule App
Figure 1-7 iPower
Cooling
iCooling: Displays the cooling full link diagram. You can view the device
information and parameter information of cooling devices and track the energy
efficiency of cooling devices.
Figure 1-8 iCooling
More
● More: Displays more functions. You can perform monitoring and maintenance
operations on devices, such as device monitoring, software upgrade,
parameter synchronization, and layout adjustment.

FusionModule App
Figure 1-9 More
● Monitor: Displays the categories and lists of all devices. You can view real-
time data or active alarms of a device, such as basic information, running
information, and temperature information.
Figure 1-10 Monitor
Setting
Figure 1-11 Setting

FusionModule App
1.2 User Guide
1.2.1 Downloading and Installing the App
App Operating Environment Requirements

● Terminal: Android PAD
● Operating system: Android 6.0 or later; system memory: 4 GB or larger
● The PAD power is sufficient.
The PAD is successfully connected to the Internet.

Users can download and install the app through the Huawei AppGallery.
● Download the app from the Huawei AppGallery.

a. Install the Huawei AppGallery app. If you have installed the app, go to
b.
i. Visit https://appgallery.huawei.com using a phone browser, tap

in the upper left corner, and install the Huawei AppGallery app.
ii. If a message similar to that in Figure 1-12 is displayed, tap any
button below the message.
Figure 1-12 Installation prompt
b. Open the Huawei AppGallery app, search for FusionModule, and tap
Install.
● Scan the QR code to download and install the app.
Scan the QR code on Maintenance > APP Obtaining on the ECC800-pro
WebUI, and download and install the app as prompted.

FusionModule App
Figure 1-13 FusionModule app QR code
The PAD cannot connect to the Internet.

Download the app from Huawei technical support website, upload the app
software package to the PAD using a mobile storage device (such as a USB flash
drive), and install the app.
1. Obtain the app software installation package from Huawei technical support
website.
– For enterprise users:
i. Log in to https://support.huawei.com/enterprise.
ii. Search for DP*fm.apk.
iii. Choose Software & Tools.
iv. Download the DP_VxxxRxxxSPCxxx_fm.apk installation package of
the latest version.
– For carriers:
i. Log in to https://support.huawei.com.
iii. Click the Software & Tools tab, and then select Product Software
under Filter by Document Type.
the latest version.
On the Software tab page, download the app software and digital signature
file.
After the downloading is complete, use the digital certificate and verification
tool available at Huawei technical support website to verify the digital
signature of the software package.
a. Contact technical support to obtain the OpenPGP Signature Verification
Guide package.
▪ For enterprise users, log in to https://support.huawei.com/

enterprise/en/tool/TL1000000054/TV1000000016.
▪ For carrier users, log in to https://support.huawei.com/carrier/

digitalSignatureAction.

FusionModule App
b. Verify the integrity of a software package by referring to OpenPGP

Signature Verification Guide.pdf. If the verification fails, do not use the
package and contact technical support.
2. Install the apps.
a. Use a mobile storage device (such as a USB flash drive) to upload the
downloaded app installation package to the PAD.
b. Click the app installation file to install it.
After the installation is complete, check that the app icon is displayed on
the PAD desktop.
1.2.2 Logging In to the App

You can log in to the app using the account and password or facial recognition.
1.2.2.1 Preparations for Login

Before logging in to the app, set Wi-Fi parameters and the WLAN IP address of
the ECC800-Pro.
Prerequisites
You have obtained the Wi-Fi SSID, Wi-Fi password, and WLAN IP address of the
ECC800-Pro.
Procedure
1. On the PAD screen, tap the app icon.
NOTE
If you log in to the app for the first time, select I have read and accept to the above
statement carefully in the Privacy Statement dialog box, and click Accept.
2. On the app login screen, choose Setting > Network Connection. Select the
WiFi SSID set on the ECC800-Pro WebUI, and enter WiFi Password to log in.
Figure 1-14 Login screen

FusionModule App
3. On the app login screen, choose Setting > Communication IP Setting, set
the WLAN IP address of the ECC800-Pro, and tap OK.
NOTE
The default IP address is 192.168.245.10. Enter the actual WLAN IP address of the
ECC800-Pro.
1.2.2.2 Logging In to the App Using the Account and Password

You can log in to the app using the account and password.
Prerequisites
● You have obtained the user name and password for ECC800-Pro WebUI login.
● The PAD is connected to the ECC800-Pro over WiFi.
Procedure
1. On the app login screen, set User Name and Password, and tap Log In.
NOTE
● The user name and password for logging in to the app are the same as those for
logging in to the ECC800-Pro WebUI.
● After logging in to the app for the first time, change the initial password and keep
the password secure. You are advised to change the password periodically (every
three months) according to the password requirements.
● A maximum of three users can log in to the ECC800-Pro at the same time. If you
need to log in to the ECC800-Pro WebUI and app at the same time, you are
advised to use different user names to log in. Otherwise, you will be forced to log
out of either of them.
1.2.2.3 Logging In to the App Through Facial Recognition

You can log in to the app using the facial recognition.

FusionModule App
1.2.2.3.1 Recording Facial Information

Only administrators can record facial information, modify associated users, and
delete facial data.
Prerequisites
● You have logged in to the app as an administrator. For details, see 1.2.2.2
Logging In to the App Using the Account and Password.
● Before recording face data by importing a file, you need to obtain the face
data file.
Procedure
1. Tap in the upper right corner of the main screen.

2. On the Setting screen, tap Face Account Management.
3. After reading the prompt, tap Confirm.
4. On the Face Account Management screen, select a recording mode based on
site requirements to record face data.
– Onsite recording: Tap ADD, enter face data as prompted, set associated
users and facial recognition login information, and tap OK.
– File import: Tap Import in the upper right corner of the screen and
import face data as prompted.
NOTE
● The face data is used only for the facial recognition function and will not be used
for other purposes. The face data is encrypted during transmission in the ECC800-
Pro to ensure that the personal data of users is fully protected.
● You can tap to modify associated users and tap to delete face data.
1.2.2.3.2 (Optional) Enabling Default Facial Recognition Login

After Default Facial Recognition Login is enabled, facial recognition is performed
by default when you log in to the app.
Prerequisites
You have recorded your facial data. For details, see 1.2.2.3.1 Recording Facial
Information.
Procedure

2. On the Setting screen, tap Switch Control Center.
3. In the Switch Control Center dialog box, tap on the right of

Default Facial Recognition Login.

FusionModule App
NOTE
● If facial recognition is performed by default when you log in to the app, you can
tap Password Login in the lower right corner of the facial recognition screen to
switch to the password login mode.
● To disable the Default Facial Recognition Login function, tap on the

right of Default Facial Recognition Login.
1.2.2.3.3 Logging In to the App Through Facial Recognition

After facial data is recorded, you can log in to the app through facial recognition.
Prerequisites
● You have recorded your facial data. For details, see 1.2.2.3.1 Recording Facial
Information.
● Enable Default Facial Recognition Login if needed. For details, see 1.2.2.3.2
(Optional) Enabling Default Facial Recognition Login.
Procedure
1. On the app login screen, tap Face Login, and align your face with the circle
on the app screen. After the recognition is successful, log in to the app.
1.2.3 Opening the Access Control System Using Facial

Recognition
Administrators can use the facial recognition function to enable the access control
function.
Prerequisites
You have recorded face data as an administrator.

FusionModule App
Procedure
On the home screen of the app, tap in the upper left corner, choose Face in
the lower right corner, and align your face with the circle on the screen. After the
recognition is successful, the access control system is opened.
1.2.4 Monitoring Device

You can view details (real-time data and active alarms) about devices such as the
monitoring system, power distribution system, aisles, cooling system, and cabinets.
Some devices support functions such as control and parameter setting.
1.2.4.1 Turning On/Off Lights

When the local switch button or linkage switch is faulty, the administrator can
turn on or off the lights using this function.
Prerequisites
● You have logged in to the app as an administrator.
● The AC actuator and FusionModule actuator have been connected to the
ECC800-Pro and are running properly.
Procedure
1. Choose More > Monitor.
2. On the Monitor screen, perform related steps based on the device type.
– AC actuator:
i. Choose Aisle > AC Actuator Group, select an AC actuator, and tap
Operation Control.
ii. On the Operation Control tab, set Route 1 control mode to Light,
and Set light Mode to Manual. Tap Submit.
Figure 1-17 Monitor 1

FusionModule App
iii. Tap or on the right of Light control to turn on or off

lights.
Figure 1-18 Monitor 2
– FusionModule actuator:
Choose Aisle > FusionModule Actuator Group, select a FusionModule
actuator, and tap Light Control.
NOTE
This operation can be performed only when Set light Mode of the FusionModule
actuator has been set to Manual on the ECC800-Pro WebUI.
1.2.4.2 Opening Scuttles

Administrators can use this function to open scuttles. This function will open the
skylights of the smart module. To close the skylights, you need to manually close
them. Exercise caution when performing this operation.
Prerequisites
● The skylight actuator and FusionModule actuator have been connected to the
ECC800-pro and are running properly.
Procedure
2. On the Monitor screen, choose Aisle > Skylight Actuator Group or Aisle >
FusionModule Actuator Group. Select a skylight actuator or FusionModule
actuator, and tap Remote Scuttle Opening.

FusionModule App
Figure 1-19 Monitor
3. In the dialog box that is displayed, enter the password for the current
administrator and tap Confirm.
NOTE
If Re-authentication is not required for this login(valid for 12Hour) is selected, no

dialog box is displayed when the user needs to perform secondary authentication
within 12 hours.
1.2.4.3 Opening Doors

If O&M personnel forget to bring the access card or forget the password and need
to enter the smart module, the administrator can open the door. Door opening
will open the door of the smart module. Exercise caution when performing this
operation.
Prerequisites
● The access actuator and FusionModule actuator have been connected to the
Procedure
2. On the Monitor screen, choose Aisle > Access Actuator Group or Aisle >
FusionModule Actuator Group. Select an access actuator or FusionModule
actuator, and tap Remote Door Opening.

FusionModule App
Figure 1-20 Monitor
NOTE

within 12 hours.
1.2.4.4 Power-On/Off Devices

Administrators can use this function to power on or off the smart cooling devices.
Prerequisites
● The smart cooling device has been connected to the ECC800-Pro and is
running properly.
● The permission to control smart cooling devices has been enabled. For details,
see 1.2.7.2 Enabling the Permission to Control Smart Cooling Devices.
Procedure
2. On the Monitor screen, tap Cooling, select a smart cooling device, and tap
ON or OFF.
NOTE
● If Re-authentication is not required for this login(valid for 12Hour) is selected,

no dialog box is displayed when the user needs to perform secondary
authentication within 12 hours.
● After the power-on/off are complete, the color of the corresponding cooling device
is updated on the iCooling screen. When the smart cooling device is started, it is
displayed in blue. When the smart cooling device is shut down, it is displayed in
gray and the related flow stops.

FusionModule App
1.2.4.5 Setting Parameters for the Busway

The administrator can set busway parameters on the app.
Prerequisites
● In the busway power distribution scenario, the general input unit or power
distribution unit of the busway has been connected to the ECC800-Pro. The
power supply branch has been configured and associated, and is running
properly.
Procedure
2. On the Monitor screen, tap Power Distribution, select the general input unit
or power distribution unit, and tap Running Parameters.
3. On the Running Parameters screen, set parameters and tap SUBMIT.
1.2.5 Maintaining Devices

You can adjust the device layout, upgrade device software, configure the ECC800-
Pro by importing and exporting a configuration file, and synchronize device
parameters.
1.2.5.1 Adjusting the Device Layout

You can adjust the device layout in the smart module by using the iFind function.
Prerequisites
● The subrack information has been created on the ECC800-Pro, and the device
layout is configured.
NOTE
● The initial layout of the iFind depends on the floor layout of the ECC800-Pro home
screen.
● The iFind layout adjustment function can be used to adjust device positions but cannot
be used to add or delete device information.
● Administrators can use the editing function of the iFind to adjust the device location
and power configuration in the plan view. Operators can only view the iFind layout and
operate devices in blink mode.
Procedure
1. Choose More > iFind.
2. On the iFind screen, perform operations as required.
– Select a device and tap Blink to perform blink control.
– Tap Edit in the upper right corner, adjust the device location, change the
device name, and configure the battery level. Tap Save.

FusionModule App
Figure 1-21 iFind
NOTE
● Press and hold on the screen for 3 seconds before dragging.

● Only one administrator can use the editing function. If the plan view on the
ECC800-pro WebUI is in the editing state, users on other mobile terminals cannot
enter the editing state.
● After any administrator edits and saves the information on the iFind, the layout
information on the Environment, Cooling, and ECC800-pro WebUI is updated
synchronously.
● The new name takes effect immediately on the iFind screen. You do not need to
tap Save.
1.2.5.2 Upgrading Device Software

You can upgrade the software versions of the ECC800-Pro and its subdevices.
Prerequisites
● The upgrade software package has been uploaded to the PAD or USB flash
drive.
NOTE
The USB flash drive must be inserted into the ECC800-Pro.
Procedure
1. Choose More > Software Upgrade.
2. On the Software Upgrade tab, tap Create Tasks.
3. On the Create Tasks screen, select the upgrade mode, select the device
upgrade software package in File Upload, and tap Upload.

FusionModule App
Figure 1-22 Create Tasks
4. In the dialog box that is displayed, tap OK.

The upload takes about 1 to 3 minutes. When the system displays the
"Uploaded successfully." message, the file is uploaded successfully. After the
upgrade file is uploaded successfully, the screen lists the components and
versions that can be upgraded using the upgrade file.
5. Tap Upgrade in the Operation column. In the dialog box that is displayed,
tap OK.
NOTE
● You can select a feature or Board Support Package (BSP) program to upgrade it
separately.
● If an upgrade feature package is not required, tap Delete in the Operation column
to delete it.
● The ECC800-Pro upgrade package includes the ECC800 software upgrade program
and BSP software upgrade program. After the upgrade using the ECC800 upgrade
package, the ECC800-Pro system will restart.
1.2.5.3 Exporting System Data

You can export device data, configuration files, historical data, or device logs to
view, analyze, or configure devices.
Prerequisites
● Devices that can store data locally, such as the integrated PDF, integrated
UPS, and smart cooling product, have been connected.
Procedure
1. Choose More > Export Data.
2. On the Export Data screen, tap Device Data, Configuration File, Historical
Data, or Device Log, set parameters as prompted, and tap Export.
NOTE
● To ensure data security, you need to enter the encryption password. Keep the
password secure so that the data package can be decompressed properly.
● If a USB flash drive is inserted into the ECC800-Pro, you can select the USB flash
drive as the export location and save the exported data to the USB flash drive.
Device logs can only be exported locally.

FusionModule App
3. After the export is successful, tap Confirm in the dialog box that is displayed.
NOTE
If device logs are exported, you can tap Share to share the exported device logs with
other terminals.
1.2.5.4 Configuring Device Data

If the types and quantities of devices connected to two ECC800-Pros are the same,
you can export the configuration file of one ECC800-Pro and import the data to
complete the configuration of the other ECC800-Pro.
Prerequisites
● The configuration file has been exported. For details, see 1.2.5.3 Exporting
System Data.
Procedure
1. Choose More > Import Data.
2. On the Import Data screen, set parameters related to data import and tap
Import.
NOTE
The encryption password is set during data export. Therefore, when selecting a
configuration file, you need to enter the encryption password of the configuration file
so that the configuration file can be imported.
3. After the import is successful, tap CONFIRM in the dialog box that is
displayed.
NOTE
The ECC800-Pro will restart after you import the configuration file.
1.2.5.5 Synchronizing Device Parameters

If you need to quickly configure devices or replace faulty device components, you
can use the parameter synchronization function to quickly import device data.
Prerequisites
● The ECC800-Pro and devices have been powered on and are running properly.
● The target device has been replaced and is displayed in the device monitoring
list.
Procedure
1. Choose More > Parameter Sync.
2. On the Parameter Sync screen, select the source device and target device,
and tap Confirm.

FusionModule App
– Source device: device before replacement or device that can be

synchronized.
– Target device: device after replacement or newly installed device.
NOTICE
● The source device can be a device that communicates properly or fails to

communicate, but the target device must be a device that communicates
properly.
● If communication between the ECC800-Pro and the device is interrupted
during parameter synchronization, the synchronization fails. Ensure that
the ECC800-Pro and the device communicate properly and synchronize
parameters again.
Figure 1-23 Parameter Sync
1.2.6 Viewing Data

You can use facial recognition to enable access control and view device
performance data, operation logs, access control events, asset information, and
device versions.
1.2.6.1 Viewing Performance Data

You can view the battery curve, battery discharge curve, or general performance
data of devices such as smart modules, PowerPODs, and preset modules.
Prerequisites
● Devices of the smart modules, PowerPODs, and preset modules have been
connected to the corresponding ECC800-Pro.

FusionModule App
Procedure
1. Choose More > Perf Data.
2. On the Perf Data screen, choose the Battery Cure, Bat Discharge Curve, or
General performance data tab.
3. On the Battery Cure, Bat Discharge Curve, or General performance data
tab, tap Setting Query Condition or in the upper right corner, set
search criteria, and tap OK.
1.2.6.2 Viewing Operation Logs

Administrators can view the operation records of all users.
Prerequisites
● An access control device, cabinet electronic lock, or fingerprint lock has been
connected, and access user management and access permission management
have been configured on the ECC800-Pro WebUI.
Procedure
1. Choose More > Operation Log.
2. On the Operation Log screen, view operation logs.
1.2.6.3 Viewing Access Control Events

You can view the records of door opening events for the access actuator, cabinet
electronic lock, smart module, and fingerprint lock.
Prerequisites
● You have logged in to the app.
Procedure
1. Choose More > Access Event.
2. On the Access Event screen, view access control events.
1.2.6.4 Viewing Asset Details

You can view device asset details such as e-labels of system devices and other
devices.
Prerequisites

FusionModule App
Procedure
1. Choose More > Asset Details.
2. On the Asset Details screen, view device asset details such as e-labels of
system devices and other devices.
NOTE
To view details about the e-label of a device, tap E-label of the device.
1.2.6.5 Querying the Device Version Information

You can view the software version and hardware version of devices.
Prerequisites
Procedure
1. Choose More > Device Version Info.
2. On the Device Version Info screen, view the hardware version and software
version of the device.
1.2.6.6 Viewing Network Parameters

You can view the network parameters of the current PAD.
Prerequisites
You have logged in to the app as an administrator.
Procedure
1. Choose More > Network Parameter.
2. On the Network Parameter screen, view the network parameters of the PAD.
1.2.7 Setting Parameters
1.2.7.1 Setting the PAD Power Control Policy

After the Intelligent Power Control switch is turned on, the PAD enters the
steady-on mode.
Procedure


FusionModule App
3. On the Switch Control Center screen, tap or on the right of

Intelligent Power Control.
CAUTION
If the PAD is steady on, the PAD screen and battery lifespan will be shortened.
Correctly set this parameter.
4. In the dialog box that is displayed, tap Confirm.
1.2.7.2 Enabling the Permission to Control Smart Cooling Devices

To start or shut down smart cooling devices, you need to enable High-Risk
Permission.
Prerequisites
Procedure

3. In the Switch Control Center dialog box, tap on the right of High-
Risk Permission.
NOTE
● After the High-Risk Permission switch is turned on, if an administrator logs out of
the app and then logs in again, the switch is turned off by default.
● To turn off the High-Risk Permission switch, tap on the right of

High-Risk Permission.
1.2.7.3 Setting the Smoke Sensor Icon Display Policy

After the Whether to display the smoke sensor icon on the Environment
screen switch is enabled, the smoke sensor icon is displayed on the Environment
screen.
Procedure

3. In the Switch Control Center dialog box, tap or on the

right of Whether to display the smoke sensor icon on the Environment
screen.

FusionModule App
1.2.7.4 Enabling the iCooling Function

If the smart module meets the iCooling configuration requirements, you can turn
on the iCooling switch on the app.
Prerequisites
Before turning on the iCooling switch, ensure that the smart module meets the
following configuration requirements:
● A cabinet-level temperature sensor has been installed.
● Electrical energy has been configured for the IT cabinet, network cabinet, and
smart cooling product.
● At least one cold aisle T/H sensor is installed for each smart cooling product.
Procedure

3. In the Switch Control Center dialog box, tap on the right of

iCooling.
NOTE
To turn off the iCooling switch, tap on the right of iCooling.
1.2.7.5 Setting the Home Screen Display Policy

Before using the app, you need to set the display policies for Home, iPower, or
iCooling on the home screen.
Procedure

2. On the Setting screen, tap Home Function Control Center.
3. In the Home Function Control Center dialog box, tap or

on the right of Home, iPower, or iCooling, and tap Finish.

FusionModule App
User Manual (FusionModule2000) 2 Smart Screen Operation Guide
2 Smart Screen Operation Guide
2.1 Feature Overview

This section describes the functions of the FusionModule app.
Home
Display the smart module layout information, including the power, power
consumption, environment, cooling capacity, PUE, load rate, space, temperature,
power distribution, cooling, and alarm overview.
Figure 2-1 Home

FusionModule App
Figure 2-2 Load Rate
Figure 2-3 Space
Figure 2-4 Temperature
Figure 2-5 Power Distribution

FusionModule App
Figure 2-6 Cooling
Figure 2-7 Alarm
Device Monitoring
Figure 2-8 Monitor

FusionModule App
Setting
Figure 2-9 Setting
2.2 User Guide
2.2.1 (Optional) Setting the Language of the Smart Screen

Before using the smart screen, users can set the language as required.
Procedure
1. On the smart screen, choose Settings > More > Languages.
2. On the Language preferences screen, tap and hold on the right of

English (United States) and drag it forward to set the language to the first
choice 1.
Figure 2-10 Setting the language

FusionModule App
2.2.2 Downloading and Installing the App
App Operating Environment Requirements

● Terminal: Android smart screen
● Operating system: Android 6.0 or later; system memory: 4 GB or larger
The smart screen is successfully connected to the Internet.

Users can download and install the app through the Huawei AppGallery.
1. Install the Huawei AppGallery app. If you have installed the app, go to 2.
a. Visit https://appgallery.huawei.com using a phone browser, tap in

the upper left corner, and install the Huawei AppGallery app.
b. If a message similar to that in Figure 2-11 is displayed, tap any button
below the message.
Figure 2-11 Installation prompt
2. Open the Huawei AppGallery app, search for FusionModule, and tap Install.
The smart screen cannot connect to the Internet.

Download the app from Huawei technical support website, upload the app
software package to the smart screen using a mobile storage device (such as a
USB flash drive), and install the app.
1. Obtain the app software installation package from Huawei technical support
website.
– For enterprise users:
i. Log in to https://support.huawei.com/enterprise.
iii. Choose Software & Tools.
the latest version.

FusionModule App
– For carriers:
i. Log in to https://support.huawei.com.
iii. Click the Software & Tools tab, and then select Product Software
under Filter by Document Type.
the latest version.
On the Software tab page, download the app software and digital signature
file.
After the downloading is complete, use the digital certificate and verification
tool available at Huawei technical support website to verify the digital
signature of the software package.
a. Contact technical support to obtain the OpenPGP Signature Verification
Guide package.
▪ For enterprise users, log in to https://support.huawei.com/

enterprise/en/tool/TL1000000054/TV1000000016.
▪ For carrier users, log in to https://support.huawei.com/carrier/

digitalSignatureAction.
b. Verify the integrity of a software package by referring to OpenPGP
Signature Verification Guide.pdf. If the verification fails, do not use the
package and contact technical support.
2. Install the apps.
a. Use a mobile storage device (such as a USB flash drive) to upload the
downloaded app installation package to the smart screen.
b. Click the app installation file to install it.
After the installation is complete, check that the app icon is displayed on
the smart screen desktop.
2.2.3 Logging In to the App

You can log in to the app using the account and password or facial recognition.
2.2.3.1 Preparations for Login

Before logging in to the app, you need to set the language and IP address, smart
module IP address, or greetings on the smart screen.
2.2.3.1.1 Setting the Smart Screen IP Address

If the smart screen is connected to the ECC800-Pro using a network cable, you
need to set the smart screen IP address.
Procedure
1. On the home smart screen, choose Settings > More > Ethernet.
2. On the Ethernet screen, turn on the switch on the right of Ethernet and set
the smart screen IP address.

FusionModule App
– Automatically obtaining network parameters: By default, the smart

screen uses DHCP to automatically set its IP address.
– Manually setting network parameters: Set Ethernet ip mode to static
and manually set network parameters.
Figure 2-12 Ethernet
2.2.3.1.2 Setting the Communication IP Address (Smart Screen Exclusively Used by

a Single Module)
Before logging in to the app, set the NetEco NMS IP address and ECC800-Pro
WLAN IP address.
Prerequisites
You have obtained the NetEco NMS IP address and ECC800-Pro WLAN IP address.
Procedure
1. On the home smart screen, tap the app icon.
NOTE
2. On the app login screen, choose Setting > Communication IP Setting.

FusionModule App
3. In the Communication IP Setting dialog box, set the NetEco NMS IP address,
large screen name, and ECC800-Pro WLAN IP address, and tap Confirm.
Figure 2-14 Communication IP setting
NOTE
ECC800-Pro.
2.2.3.1.3 Setting the Communication IP Address (Smart Screen Shared by Multiple

Modules)
Before logging in to the app, set the NetEco NMS IP address and ECC800-Pro
WLAN IP address.
Prerequisites
● You have obtained the NetEco NMS IP address and ECC800-Pro WLAN IP
address.
● You have obtained the predefined large-screen information created on the
NetEco and the user name and password for accessing the third-party system.
Procedure
1. On the home smart screen, tap the app icon.
NOTE
2. On the app login screen, choose Setting > Communication IP Setting.

FusionModule App
3. In the Communication IP Setting dialog box, set the NetEco NMS IP address
and screen name.
Figure 2-16 Communication IP setting
4. Tap Select the NMS. In the Use a third party NMS account to log in dialog
box, enter the third-party username and password created on the NetEco, and
tap CONFIRM.
5. In the Please choose NMS large screen dialog box, select one of the
predefined large-screen lists configured on the NetEco, and tap CONFIRM.

FusionModule App
Figure 2-17 Choose NMS large screen
6. Add a smart module based on site requirements and set the IP address for the
smart module to connect to the corresponding ECC800.
NOTE
● The default IP address is 192.168.245.10. Enter the actual WLAN IP address of the
ECC800-Pro.
● Tap or to add or delete a smart module.
7. Tap in the lower left corner of the home screen. In the displayed device
floating disk, tap the corresponding smart module and NetEco predefined
large screen to switch between the display screens.
NOTE
Each time you switch to a screen, the corresponding login screen is automatically
displayed.
Figure 2-18 Switch smart modules
8. On the displayed login screen, enter the user name and password of the
ECC800 or log in to the ECC800 using facial recognition to view the smart
module information.

FusionModule App
NOTE
● When you log in to the NetEco predefined large screen for the first time, you need
to enter the user name and password for logging in to the NetEco WebUI.
● When a user records the same face in multiple smart modules, the user can log in
to one smart module and then switch to the other smart module without login
again.
2.2.3.1.4 (Optional) Setting Greetings

You can set the greetings to be displayed at the top of the home smart screen.
Prerequisites
The smart screen has been connected to the ECC800-Pro over a network cable.
Procedure
1. On the smart screen, tap the app icon.
NOTE
2. On the app login screen, choose Setting > Greeting Settings.
3. In the Greeting Settings dialog box, enter the greeting information, and then
tap OK.

FusionModule App
Figure 2-20 Greeting Settings
2.2.3.2 Logging In to the App Using the Account and Password

You can log in to the app using the account and password.
Prerequisites
● You have obtained the user name and password for ECC800-Pro WebUI login.
● The smart screen has been connected to the ECC800-Pro over a network
cable.
Procedure
1. On the app login screen, set User Name and Password, and tap Log In.

FusionModule App
NOTE
● The user name and password for logging in to the app are the same as those for
logging in to the ECC800-Pro WebUI.
● After logging in to the app for the first time, change the initial password and keep
the password secure. You are advised to change the password periodically (every
three months) according to the password requirements.
● A maximum of three users can log in to the ECC800-Pro at the same time. If you
need to log in to the ECC800-Pro WebUI and app at the same time, you are
advised to use different user names to log in. Otherwise, you will be forced to log
out of either of them.
2.2.3.3 Logging In to the App Through Facial Recognition

You can log in to the app using the facial recognition.
2.2.3.3.1 Recording Facial Information

Only administrators can record facial information, modify associated users, and
delete facial data.
Prerequisites
● You have logged in to the app as an administrator. For details, see 2.2.3.2
Logging In to the App Using the Account and Password.
● Before recording face data by importing a file, you need to obtain the face
data file.
Procedure

2. On the Setting screen, tap Face Account Management.

FusionModule App
Figure 2-22 Setting
3. After reading the prompt, tap Confirm.

4. On the Face Account Management screen, tap Add on the right.

FusionModule App
Figure 2-23 Face Account Management
5. In the Enroll Face dialog box, select a recording mode based on site
requirements.
Figure 2-24 Enroll Face
– Onsite recording: Tap ENROLL, enter face data as prompted, set

associated users and facial recognition login information, and tap OK.
– File import: Tap IMPORT FILE and import face data as prompted.
NOTE
● The facial data is used only for configuring the facial recognition function and is
not used for other purposes. The facial data is encrypted during transmission in the
ECC800-Pro to ensure that the personal data of users is fully protected.
● You can tap to modify associated users and tap to delete facial data.

FusionModule App
2.2.3.3.2 (Optional) Enabling Default Facial Recognition Login

After Default Facial Recognition Login is enabled, facial recognition is performed
by default when you log in to the app.
Prerequisites
You have recorded your facial data. For details, see 2.2.3.3.1 Recording Facial
Information.
Procedure
1. Tap in the lower right corner of the main screen.

Figure 2-25 Setting
3. In the Switch Control Center dialog box, tap on the right of Default
Facial Recognition Login.

FusionModule App
Figure 2-26 Switch Control Center
NOTE
● If facial recognition is performed by default when you log in to the app, you can
tap Password Login in the lower right corner of the facial recognition screen to
switch to the password login mode.
● To disable the Default Facial Recognition Login function, tap on the right
of Default Facial Recognition Login.
4. In the Switch Control Center dialog box, tap OK.
2.2.3.3.3 Logging In to the App Through Facial Recognition

After facial data is recorded, you can log in to the app through facial recognition.
Prerequisites
● You have recorded your facial data. For details, see 2.2.3.3.1 Recording Facial
Information.
● Enable Default Facial Recognition Login if needed. For details, see 2.2.3.3.2
(Optional) Enabling Default Facial Recognition Login.
Procedure
1. On the app login screen, tap Face Login, and align your face with the circle
on the app screen. After the recognition is successful, log in to the app.

FusionModule App
2.2.4 Switching Smart Modules

In the scenario where multiple modules share the smart screen, you can switch to
display the configured smart module information. Only FusionModule2000 5.0
supports smart screen sharing among multiple modules.
Prerequisites
● Multiple modules have been configured to share the smart screen. For details,
see 2.2.3.1.3 Setting the Communication IP Address (Smart Screen Shared
by Multiple Modules).
Procedure
1. On the home smart screen, tap in the lower left corner.
2. In the displayed device floating disk, tap the corresponding smart module and
NetEco predefined large screen to switch between the display screens.
NOTE
Each time you switch to a screen, the corresponding login screen is automatically
displayed.

FusionModule App
Figure 2-28 Switching smart modules
3. On the displayed login screen, enter the user name and password of the
ECC800-Pro. The corresponding smart module information is displayed.
NOTE
● When you log in to the NetEco predefined large screen for the first time, you need
to enter the user name and password for logging in to the NetEco WebUI.
● When a user records the same face in multiple smart modules, the user can log in
to one smart module and then switch to the other smart module without login
again.
2.2.5 Monitoring Device

Users can view real-time data and active alarms of devices such as the monitoring
system, power distribution system, aisles, cooling system, and cabinets. In
addition, users can control devices and set parameters.
2.2.5.1 Turning On/Off Lights

When the local switch button or linkage switch is faulty, the administrator can
turn on or off the lights using this function.
Prerequisites
● The AC actuator and FusionModule actuator have been connected to the
Procedure
1. On the home screen, tap Monitor in the lower right corner.
2. On the Monitor screen, perform related steps based on the device type.
– AC actuator:
i. Choose Aisle > AC Actuator Group, select an AC actuator, and tap
Runing Parameters on the right of the AC actuator.
ii. On the Operation Control tab, set Route 1 control mode to Light,
and Set light Mode to Manual. Tap Submit.

FusionModule App
iii. Tap or on the right of Light control to turn on or

off lights.
iv. In the dialog box that is displayed, tap Confirm.
– FusionModule actuator:
Choose Aisle > FusionModule Actuator Group, select a FusionModule
actuator, and tap Light Control.
NOTE
This operation can be performed only when Set light Mode of the FusionModule
actuator has been set to Manual on the ECC800-Pro WebUI.
2.2.5.2 Opening Scuttles

Administrators can use this function to open scuttles. Scuttle opening will open
the skylight of the smart module. Exercise caution when performing this
operation.
Prerequisites
● The skylight actuator and FusionModule actuator have been connected to the
ECC800-pro and are running properly.
Procedure
2. On the Monitor screen, choose Aisle > Skylight Actuator Group or Aisle >
FusionModule Actuator Group. Select a skylight actuator or FusionModule
actuator, and tap Remote Scuttle Opening.
NOTE

within 12 hours.
2.2.5.3 Opening Doors

If O&M personnel forget to bring the access card or forget the password and need
to enter the smart module, the administrator can open the door. Door opening
will open the door of the smart module. Exercise caution when performing this
operation.
Prerequisites

FusionModule App
Procedure
2. On the Monitor screen, choose Aisle > Access Actuator Group or Aisle >
FusionModule Actuator Group. Select an access actuator or FusionModule
actuator, and tap Remote Door Opening.
NOTE

within 12 hours.
2.2.5.4 Unlocking
If O&M personnel forget to bring the cabinet lock keys and need to open the
cabinet electronic lock, administrators can unlock the cabinet electronic lock.
Unlocking will open the electronic lock of the cabinet. Exercise caution when
performing this operation.
Prerequisites
Procedure
2. On the Monitor screen, choose Cabinet > IT Cabinet > Cabinet Electronic
Lock, select the cabinet electronic lock, and tap Remote Unlocking.
NOTE

within 12 hours.
2.2.5.5 Power-On/Off Devices

Administrators can use this function to power on or off the smart cooling devices.
Prerequisites
● The smart cooling device has been connected to the ECC800-Pro and is
running properly.
● The permission to control smart cooling devices has been enabled. For details,
see 2.2.8.1 Enabling the Permission to Control Smart Cooling Devices.

FusionModule App
Procedure
2. On the Monitor screen, tap Cooling, select the smart cooling device, and tap
ON or OFF on the right of the smart cooling device.
NOTE
● If Re-authentication is not required for this login(valid for 12Hour) is selected,

no dialog box is displayed when the user needs to perform secondary
authentication within 12 hours.
● After the power-on/off are complete, the color of the corresponding cooling device
is updated on the iCooling screen. When the smart cooling device is started, it is
displayed in blue. When the smart cooling device is shut down, it is displayed in
gray and the related flow stops.
2.2.5.6 Setting Parameters for the Busway

The administrator can set busway parameters on the app.
Prerequisites
● In the busway power distribution scenario, the general input unit or power
distribution unit of the busway has been connected to the ECC800-Pro. The
power supply branch has been configured and associated, and is running
properly.
Procedure
2. On the Monitor screen, tap Power Distribution, select the general input unit
or power distribution unit, and tap Running Parameters.
3. On the Running Parameters screen, set parameters and tap SUBMIT.
2.2.6 Maintaining Devices

You can adjust the device layout, upgrade device software, configure the ECC800-
Pro by importing and exporting a configuration file, and synchronize device
parameters.
2.2.6.1 Adjusting the Device Layout

You can adjust the device layout in the smart module by using the iFind function.
Prerequisites
● The subrack information has been created on the ECC800-Pro, and the device
layout is configured.

FusionModule App
NOTE
● The initial layout of the iFind depends on the floor layout of the ECC800-Pro home
screen.
● The iFind layout adjustment function can be used to adjust device positions but cannot
be used to add or delete device information.
● Administrators can use the editing function of the iFind to adjust the device location
and power configuration in the plan view. Operators can only view the iFind layout and
operate devices in blink mode.
Procedure
1. On the home screen, choose Functions > iFind in the lower right corner.
2. On the iFind screen, perform operations as required.
– Select a device and tap Blink to perform blink control.
– Tap Edit in the upper right corner, adjust the device location, change the
device name, and configure the battery level. Tap Save.
Figure 2-29 iFind
NOTE
● Put your finger on the device and drag it.

● Only one administrator can use the editing function. If the plan view on the
ECC800-Pro WebUI is in the editing state, users on other mobile terminals cannot
enter the editing state.
● After any administrator edits and saves the information on the iFind, the layout
information on the Cooling, and WebUI is updated synchronously.
● The new name takes effect immediately on the iFind screen. You do not need to
tap Save.
2.2.6.2 Upgrading Device Software

You can upgrade the software versions of the ECC800-Pro and its subdevices.
Prerequisites

FusionModule App
● The upgrade software package has been uploaded to the smart screen or USB
flash drive.
NOTE
The USB flash drive must be inserted into the ECC800-Pro.
Procedure
1. On the home screen, choose Functions > Upgrade in the lower right corner.
2. On the Create Tasks screen, select the upgrade mode, select the device
upgrade software package in File Upload, and tap Upload.
Figure 2-30 Upgrade

The upload takes about 1 to 3 minutes. When the system displays the
"Uploaded successfully." message, the file is uploaded successfully. After the
upgrade file is uploaded successfully, the screen lists the components and
versions that can be upgraded using the upgrade file.
4. Tap Upgrade in the Operation column. In the dialog box that is displayed,
tap OK.
NOTE
● You can select a feature or Board Support Package (BSP) program to upgrade it
separately.
● If an upgrade feature package is not required, tap Delete in the Operation column
to delete it.
● The ECC800-Pro upgrade package includes the ECC800 software upgrade program
and BSP software upgrade program. After the upgrade using the ECC800 upgrade
package, the ECC800-Pro system will restart.
2.2.6.3 Exporting System Data

You can export device data, configuration files, historical data, or device logs to
view, analyze, or configure devices.

FusionModule App
Prerequisites
● Devices that can store data locally, such as the integrated PDF, integrated
UPS, and smart cooling product, have been connected.
Procedure
1. On the home screen, choose Functions > Export Data in the lower right
corner.
2. On the Export Data screen, tap Device Data, Configuration File, Historical
Data, or Device Log, set parameters as prompted, and tap Export.
Figure 2-31 Export Data
NOTE
● To ensure data security, you need to enter the encryption password. Keep the
password secure so that the data package can be decompressed properly.
● If a USB flash drive is inserted into the ECC800-Pro, you can select the USB flash
drive as the export location and save the exported data to the USB flash drive.
Device logs can only be exported locally.
3. After the export is successful, tap Confirm in the dialog box that is displayed.
NOTE
If device logs are exported, you can tap Share to share the exported device logs with
other terminals.
2.2.6.4 Configuring Device Data

If the types and quantities of devices connected to two ECC800-Pros are the same,
you can export the configuration file of one ECC800-Pro and import the data to
complete the configuration of the other ECC800-Pro.
Prerequisites

FusionModule App
● The configuration file has been exported. For details, see 2.2.6.3 Exporting
System Data.
Procedure
1. On the home screen, choose Functions > Import Data in the lower right
corner.
2. On the Import Data screen, set parameters related to data import and tap
Import.
Figure 2-32 Import Data
NOTE
The encryption password is set during data export. Therefore, when selecting a
configuration file, you need to enter the encryption password of the configuration file
so that the configuration file can be imported.
3. After the import is successful, tap CONFIRM in the dialog box that is
displayed.
NOTE
The ECC800-Pro will restart after you import the configuration file.
2.2.6.5 Synchronizing Device Parameters

If you need to quickly configure devices or replace faulty device components, you
can use the parameter synchronization function to quickly import device data.
Prerequisites
● The target device has been replaced and is displayed in the device monitoring
list.

FusionModule App
Procedure
1. On the home screen, choose Functions > Synchronize in the lower right
corner.
2. On the Parameter Sync screen, select the source device and target device,
and tap Confirm.
Figure 2-33 Parameter Sync
– Source device: device before replacement or device that can be

synchronized.
– Target device: device after replacement or newly installed device.
NOTICE
● The source device can be a device that communicates properly or fails to

communicate, but the target device must be a device that communicates
properly.
● If communication between the ECC800-Pro and the device is interrupted
during parameter synchronization, the synchronization fails. Ensure that
the ECC800-Pro and the device communicate properly and synchronize
parameters again.
2.2.7 Viewing Data
2.2.7.1 Viewing Performance Data

You can view the general performance data, battery discharge curve, or battery
curve of devices such as smart modules, power modules, and preset modules.
Prerequisites
● Devices of the smart modules, PowerPODs, and preset modules have been
connected to the corresponding ECC800-Pro.

FusionModule App
● The policy for displaying performance data has been set. For details, see
2.2.8.5 Setting the Policy for Displaying Performance Data.
Procedure
1. On the home screen, choose Functions > Perf Data in the lower right corner.
2. On the Perf Data screen, tap on the right of General Performance Data,
Battery Discharge, or Battery Curve.
3. In the General Performance Data Setting, Battery Discharge Setting, or
Battery Curve Setting dialog box, set search criteria and tap FINISH.
2.2.7.2 Viewing Asset and Version Information

You can view the asset details and version information of a device.
Prerequisites
Procedure
1. On the home screen, choose Functions > Asset&Version in the lower right
corner.
2. On the Asset&Version screen, view asset details and device version
information.
Figure 2-34 Asset&Version
NOTE
To view details about the e-label of a device, tap E-label of the device.
2.2.7.3 Viewing Logs and Access Control Information

You can view operation records of all users and door opening events of the access
actuator, cabinet electronic lock, smart module, and fingerprint lock.

FusionModule App
Prerequisites
Procedure
1. On the home screen, choose Functions > Log&Access in the lower right
corner.
2. On the Log&Access screen, view operation logs and access control events.
2.2.7.4 Viewing Energy Efficiency Information

Users can view the energy efficiency information of cabinets and track the energy
efficiency of devices.
Prerequisites
Procedure
1. On the home screen, choose Functions > Energy in the lower right corner.
2. On the Energy screen, view the energy efficiency information of cabinets and
track the energy efficiency of devices.
Figure 2-35 Energy
2.2.8 Parameter Settings
2.2.8.1 Enabling the Permission to Control Smart Cooling Devices

To start or shut down smart cooling devices, you need to enable High-Risk
Permission.

FusionModule App
Prerequisites
Procedure

Figure 2-36 Setting
3. In the Switch Control Center dialog box, tap on the right of High-
Risk Permission.

FusionModule App
NOTE
● After the High-Risk Permission switch is turned on, if an administrator logs out of
the app and then logs in again, the switch is turned off by default.
● To turn off the High-Risk Permission switch, tap on the right of High-
Risk Permission.
5. In the Switch Control Center dialog box, tap CONFIRM.
2.2.8.2 Enabling the iCooling Function

If the smart module meets the iCooling configuration requirements, you can turn
on the iCooling switch on the app.
Prerequisites
Before turning on the iCooling switch, ensure that the smart module meets the
following configuration requirements:
● A cabinet-level temperature sensor has been installed.

● Electrical energy has been configured for the IT cabinet, network cabinet, and
smart cooling product.
● At least one cold aisle T/H sensor is installed for each smart cooling product.

FusionModule App
Procedure

3. In the Switch Control Center dialog box, tap on the right of iCooling.

FusionModule App
NOTE
To turn off the iCooling switch, tap on the right of iCooling.

4. In the Switch Control Center dialog box, tap CONFIRM.
2.2.8.3 Setting the Display Policy of Cards on the Home Screen

You can set the display policy for the power, power consumption, environment,
cooling capacity, PUE, and alarm cards on the home screen as required.
Procedure

2. On the Setting screen, tap Card Control Center.

FusionModule App
Figure 2-40 Setting
3. In the Card Control Center dialog box, tap or on the right of

Power, Power Consumption, Environment, Cooling, PUE, or Alarms.

FusionModule App
Figure 2-41 Card Control Center
4. In the Card Control Center dialog box, tap CONFIRM.
2.2.8.4 Setting the Home Screen Display Policy

You can set the display policy of the load rate, space, temperature, power
distribution, and cooling functions on the home screen as required.
Procedure

2. On the Setting screen, tap Home Function Control Center.

FusionModule App
Figure 2-42 Setting
3. In the Home Function Control Center dialog box, tap or Load

Rate, Space, TEMP, Power Distribution, or Cooling.

FusionModule App
Figure 2-43 Home Function Control Center
4. In the Home Function Control Center dialog box, tap CONFIRM.
2.2.8.5 Setting the Policy for Displaying Performance Data

You can set the policy for displaying General Performance Data, Battery
Discharge Curve, or Battery Curve on the Performance Data screen as required.
Procedure

2. On the Setting screen, tap Performance Data Control Center.

FusionModule App
Figure 2-44 Setting
3. In the Performance Data Control Center dialog box, tap or on

the right of General Performance Data, Battery Discharge Curve, or Battery
Curve.

FusionModule App
Figure 2-45 Performance Data Control Center
4. In the Performance Data Control Center dialog box, tap CONFIRM.
2.2.8.6 Setting the Communication IP Address

If the NetEco NMS IP address, large screen name, or ECC800-Pro WLAN IP address
is changed, you can use this function to change the communication IP address.
Prerequisites
You have obtained the NetEco NMS IP address and ECC800-Pro WLAN IP address.
Procedure

2. On the Setting screen, tap Communication IP Setting.

FusionModule App
Figure 2-46 Setting
3. In the Communication IP Setting dialog box, set the NetEco NMS IP address,
large screen name, or ECC800-Pro WLAN IP address, and tap Confirm.

FusionModule App
Figure 2-47 Communication IP Setting
NOTE
ECC800-Pro.
2.2.8.7 Setting Greetings

You can set the greetings to be displayed in the upper part of the Home screen on
the smart screen as required.
Procedure

2. On the Setting screen, tap Greeting Settings.

FusionModule App
Figure 2-48 Setting
3. In the Greeting Settings dialog box, enter the greeting information, and then
tap OK.

FusionModule App
Figure 2-49 Greeting Settings
2.2.8.8 Setting the Big Screen Location

You can set the location of smart screen on the home screen based on the actual
installation position.
Procedure

2. On the Setting screen, tap Big Screen Location Setting.

FusionModule App
Figure 2-50 Setting
3. In the Big Screen Location Setting dialog box, set the smart screen position
based on the actual installation position, and tap CONFIRM.

FusionModule App
Figure 2-51 Big Screen Location Setting

FusionModule App
User Manual (FusionModule2000) 3 FAQs
3 FAQs
3.1 What Do I Do If Login Fails?

Table 3-1 Login exceptions
Message Possible Causes Troubleshooting
Network Exception ● The WiFi connection ● Check whether the

fails. WiFi module is
● The app properly connected to
communication IP the ECC800-Pro. If no,
address is incorrectly reconnect them.
set. ● Setting the App
communication IP
address
On the app login
screen, choose
Setting >
Communication IP
Setting, set the
WLAN IP address of
the ECC800-Pro, and
tap OK.

FusionModule App
Message Possible Causes Troubleshooting
Invalid user name or ● WiFi connection error ● Check the WiFi

incorrect password occurs. connection to ensure
● The WiFi connection that the connection is
is normal, but the normal.
user has not been ● Check whether the
registered. user exists. If not,
perform the following
steps to add the user:
1. Log in to the
ECC800-Pro WebUI
as an
administrator.
2. Choose
Maintenance >
User
Management, and
add a user on the
User
Management
page.
Login failed because the The password has 1. Log in to the ECC800-
password has expired expired. Pro WebUI as an
administrator.
2. Choose Maintenance
> User Management.
The user
management page is
displayed.
3. Select the user to be
modified and click
Modify. On the page
that is displayed, reset
the login password.
Login failed The face token has Check whether the face
expired. data has been recorded
in the smart module.
3.2 What Do I Do If the Power Distribution View Does

Not Display the Circuit Diagram?
Symptom
The circuit diagram is not displayed in the power distribution view on the app.

FusionModule App
Possible Causes
Two different types of power distribution devices are connected to the
FusionModule2000 or the current power distribution mode is a non-standard
power distribution solution. As a result, the power distribution link cannot be
properly displayed on the app.
Solution
Verify that only one type of power distribution device is connected to the
FusionModule2000 and the current power distribution mode is the standard power
distribution solution.
3.3 What Do I Do If the U Space Proportion Is Not

Displayed on the App?
Symptom
After the ECC800-Pro is connected to the NetEco, the U space proportion is not
displayed on the app.
Possible Causes
Assets corresponding to U spaces are not allocated on the NetEco.
Solution
Allocate the assets of the corresponding U space on the NetEco. For details, see
"Allocating a Device" in NetEco Product Documentation (Data Center).
3.4 What Do I Do If a Smoke Sensor or Water Sensor Is

Not Displayed on the App?
After connecting water and smoke sensors, log in to the ECC800-Pro WebUI and
place the sensors in the layout diagram through the smart module layout. For
details, see ECC800-Pro Data Center Controller User Manual.

FusionModule App
User Manual (FusionModule2000) A Acronyms and Abbreviations
A Acronyms and Abbreviations
A
APP Application
B
BIM Battery Interface Module
BSP Board Support Package
E
ECC Energy Control Center
I
IP Internet Protocol
P
PDU Power Distribution Unit
PUE Power Usage Effectiveness
S
SSID Service Set Identifier
U
UPS Uninterruptible Power System
W
WiFi Wireless Fidelity

FusionModule App User Manual (FusionModule2000) (2)

Uploaded by

Copyright:

Available Formats

FusionModule App User Manual (FusionModule2000) (2)

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FusionModule App User Manual (FusionModule2000) (2)

Uploaded by

Copyright:

Available Formats

FusionModule App

User Manual (FusionModule2000)

HUAWEI DIGITAL POWER TECHNOLOGIES CO., LTD.

Trademarks and Permissions

Huawei Digital Power Technologies Co., Ltd.

Futian, Shenzhen 518043

People's Republic of China

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. i

About This Document

Indicates a hazard with a high level of risk which, if not

Indicates a hazard with a medium level of risk which, if not

Indicates a hazard with a low level of risk which, if not

Indicates a potentially hazardous situation which, if not

Supplements the important information in the main text.

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. ii

01 2024-01-05 This is the first official release.

About This Document................................................................................................................ ii

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. iv

1.2.7.1 Setting the PAD Power Control Policy.................................................................................................................... 22

2 Smart Screen Operation Guide.......................................................................................... 25

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. v

2.2.8.2 Enabling the iCooling Function................................................................................................................................. 55

A Acronyms and Abbreviations............................................................................................. 73

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. vi

1 PAD Operation Guide

1.1 Feature Overview

Figure 1-1 Home

● Resource: Displays resource information such as the power, cooling capacity,

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. 1

Figure 1-2 Resource

● Energy: Displays the energy efficiency information of the cabinet, including

Figure 1-3 Energy

● Environment: Displays the cabinet environment information and detailed

Figure 1-4 Environment

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. 2

Figure 1-5 Active Alarms

Figure 1-6 Historical Alarms

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. 3

Figure 1-7 iPower

Figure 1-8 iCooling

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. 4

Figure 1-9 More

Figure 1-10 Monitor

Figure 1-11 Setting

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. 5

1.2 User Guide

1.2.1 Downloading and Installing the App

App Operating Environment Requirements

The PAD is successfully connected to the Internet.

● Download the app from the Huawei AppGallery.

i. Visit https://appgallery.huawei.com using a phone browser, tap

Figure 1-12 Installation prompt

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. 6

Figure 1-13 FusionModule app QR code

The PAD cannot connect to the Internet.

▪ For enterprise users, log in to https://support.huawei.com/

▪ For carrier users, log in to https://support.huawei.com/carrier/

Issue 01 (2024-01-05) Copyright © Huawei Digital Power Technologies Co., Ltd. 7

b. Verify the integrity of a software package by referring to OpenPGP

1.2.2 Logging In to the App