ChatGPT 4 | Midjourney | Claude | Suno, [10/17/24, 5:03 PM]
Certainly! Below is an example code for interfacing the MAX30100 sensor, LCD, and HC-05 Bluetooth
module using the PIC16F877A microcontroller in MikroC. This code assumes that you have already set
up your Proteus simulation correctly.
▎Code Explanation
1. I2C: Used for communicating with the MAX30100.
2. UART: Used for Bluetooth communication with the HC-05.
3. LCD: Used for displaying data.
▎MikroC Code
// Include necessary libraries
#include <built_in.h>
#include <string.h>
// I2C and UART configurations
sbit LCD_RS at RB0_bit;
sbit LCD_EN at RB1_bit;
sbit LCD_D4 at RB2_bit;
sbit LCD_D5 at RB3_bit;
sbit LCD_D6 at RB4_bit;
sbit LCD_D7 at RB5_bit;
sbit LCD_RS_Direction at TRISB0_bit;
sbit LCD_EN_Direction at TRISB1_bit;
sbit LCD_D4_Direction at TRISB2_bit;
sbit LCD_D5_Direction at TRISB3_bit;
sbit LCD_D6_Direction at TRISB4_bit;
sbit LCD_D7_Direction at TRISB5_bit;
// MAX30100 I2C address
#define MAX30100_ADDRESS 0x57
// Function prototypes
void I2C_Init();
void I2C_Start();
void I2C_Stop();
void I2C_Write(unsigned char data);
unsigned char I2C_Read(unsigned char ack);
void MAX30100_Init();
void Read_MAX30100();
void Send_Data_Bluetooth(char* data);
char buffer[20];
void main() {
// Initialize peripherals
ADCON1 = 0x06; // Configure AN pins as digital I/O
TRISB = 0x00; // Set PORTB as output for LCD
TRISC = 0x80; // Set RC7 as input (RX) and RC6 as output (TX)
// Initialize UART
UART1_Init(9600);
// Initialize I2C
I2C_Init();
// Initialize LCD
Lcd_Init();
Lcd_Cmd(_LCD_CLEAR);
Lcd_Cmd(_LCD_CURSOR_OFF);
// Initialize MAX30100 sensor
MAX30100_Init();
while (1) {
// Read data from MAX30100
Read_MAX30100();
// Send data over Bluetooth
Send_Data_Bluetooth(buffer);
// Display on LCD
Lcd_Out(1, 1, buffer);
Delay_ms(1000); // Delay for a second
void I2C_Init() {
SSPCON = 0b00101000; // Configure I2C Master mode
SSPADD = 49; // Set clock frequency (Fosc/(4*(SSPADD+1)))
void I2C_Start() {
SSPCON2bits.SEN = 1; // Start condition
while (SSPCON2bits.SEN); // Wait for completion
void I2C_Stop() {
SSPCON2bits.PEN = 1; // Stop condition
while (SSPCON2bits.PEN); // Wait for completion
void I2C_Write(unsigned char data) {
SSPBUF = data; // Load data to SSPBUF
while (!SSPSTATbits.BF); // Wait until transmission is complete
}
unsigned char I2C_Read(unsigned char ack) {
unsigned char data;
SSPCON2bits.RCEN = 1; // Enable receive mode
while (!SSPSTATbits.BF); // Wait until data is received
data = SSPBUF; // Read received data
if (ack) {
SSPCON2bits.ACKDT = 0; // Send ACK
} else {
SSPCON2bits.ACKDT = 1; // Send NACK
SSPCON2bits.ACKEN = 1; // Send ACK/NACK
while (SSPCON2bits.ACKEN); // Wait for completion
return data;
void MAX30100_Init() {
I2C_Start();
I2C_Write(MAX30100_ADDRESS << 1); // Write mode
I2C_Write(0x6B); // Mode configuration register
I2C_Write(0x03); // Set to multi-mode, sample averaging 4
I2C_Stop();
void Read_MAX30100() {
unsigned char red, ir;
I2C_Start();
I2C_Write(MAX30100_ADDRESS << 1); // Write mode
I2C_Write(0x00); // Point to FIFO data register
I2C_Stop();
I2C_Start();
I2C_Write((MAX30100_ADDRESS << 1) | 1); // Read mode
red = I2C_Read(1); // Read RED value with ACK
ir = I2C_Read(0); // Read IR value with NACK
I2C_Stop();
sprintf(buffer, "R:%d I:%d", red, ir); // Format the output string
void Send_Data_Bluetooth(char* data) {
UART1_Write_Text(data);
}
▎Key Notes:
• Ensure that your connections in Proteus match the pin configurations in the code.
• Adjust the MAX30100 initialization parameters according to your specific needs.
ChatGPT 4 | Midjourney | Claude | Suno, [10/17/24, 5:03 PM]
• The code uses a simple delay loop for timing; you may want to implement a more sophisticated timing
mechanism depending on your application.
• Make sure to include error handling in a production environment.
▎Simulation:
You can simulate this setup in Proteus by connecting the components as per your circuit design and then
uploading this code to your PIC16F877A microcontroller. Adjust any specific configurations based on
your actual hardware setup.
