3500C Marine Propulsion Engines Media Number -SEBU8225-06 Publication Date -01/05/2007 Date Updated -01/03/2021
i07452168
Overhaul (Top End)
SMCS - 7595-020-TE
Refer to this Operation and Maintenance Manual, "Maintenance Recommendations" to determine the maintenance interval for a top end overhaul.
A top end overhaul involves the removal, the inspection, and the rework of the cylinder head components. Some additional components are replaced and serviced.
Your Cat dealer can provide these services and components. Your Cat dealer can ensure that the components are operating within the appropriate specifications.
Note: The driven equipment may also require service when the engine is overhauled. Refer to the literature that is provided by the OEM of the driven equipment.
First Top End Overhaul
If you elect to perform an overhaul without the services of a Cat dealer, be aware of the following recommendations.
Cylinder Head Assembly
Inspect the cylinder head assembly according to the instructions that are in Caterpillar reusability publications. Refer to Guidelines for Reusable Parts and Salvage Operations, SEBF8029, "Index of Publications on Reusability or Salvage of Used Parts".
Your Cat dealer can provide these services and components. Your Cat dealer can ensure that the components are operating within the appropriate specifications.
The use of out-of-spec parts will cause unscheduled downtime and/or costly repairs.
Replace the unit injectors. Consult your Cat dealer about exchanging the unit injectors. Your Cat dealer can provide these services and components.
The wear of unit injectors is affected by the following considerations:
• Quality of the fuel
• Quality of the filtration of the fuel
The wear of the unit injectors can result in elevated levels of exhaust emissions and/or poor engine performance. The misfire of a single cylinder is not typically attributed to normal wear. This condition can be repaired by replacing the faulty unit injector.
The following lists of circumstances indicate that the unit injectors should be inspected more frequently:
• Use of fuels that are not recommended in this Operation and Maintenance Manual, "Fluid Recommendations"
• Extreme ambient temperatures that reduce the ability of the fuel to provide lubrication
• Frequent plugging of the fuel filters
• Insufficient maintenance of the fuel tank or the fuel storage tank that can allow excessive water, sediment, and other foreign matter.
• Insufficient maintenance of the fuel filters
Oil Suction Screen
Clean the oil suction screen after the oil has been drained.
Note: Approximately 1 L (1 qt) of oil will remain in the oil housing after the sump has been drained. This oil will pour out of the oil housing when the cover is removed. Prepare to catch the oil in a pan. Clean up any spilled oil with absorbent towels or pillows. DO NOT use absorbent particles to clean up the oil.
1. Remove the cover.
2. Remove the screen assembly according to the instructions in the Service Manual, "Disassembly and Assembly" module. Discard the used O-ring seals.
3. Inspect the screen assembly. Obtain a new screen assembly, if necessary.
4. Wash the screen assembly in clean nonflammable solvent. Allow the screen assembly to dry before installation.
5. Install the screen assembly and install new O-ring seals according to the instructions in the Service Manual, "Disassembly and Assembly" module.
7. Remove side covers to gain access to the sump. Clean the bottom of the sump with absorbent towels or pillows. When the bottom of the sump is clean, install the side covers.
Replacement of Components
Replace the following components during the top end overhaul:
• Electronic unit injectors
• Check valve assembly (duplex filter group)
Inspection, Reconditioning, or Exchanging of Components
Inspect the following components according to the instructions that are in Caterpillar reusability publications. Refer to Guidelines for Reusable Parts and Salvage Operations, SEBF8029, "Index of Publications on Reusability or Salvage of Used Parts".
Recondition the worn components or exchange the components, if necessary. Your Cat dealer can provide these services and components.
Inspect the following components according to the instructions that are in Caterpillar reusability publications. Refer to Guidelines for Reusable Parts and Salvage Operations, SEBF8029, "Index of Publications on Reusability or Salvage of Used Parts".
• Aftercooler core
• Camshaft
• Driven equipment (alignment)
• Engine control module
• Exhaust bellow shields
• Oil suction screen
Inspect and Lubricate
Inspect and lubricate the following (If Equipped):
• Duplex oil control valve linkage
Top End Overhaul (Second)
If you elect to perform an overhaul without the services of a Cat dealer, be aware of the following recommendations.
Cylinder Head Assembly
Inspect the cylinder head assembly according to the instructions that are in Caterpillar reusability publications. Refer to Guidelines for Reusable Parts and Salvage Operations, SEBF8029, "Index of Publications on Reusability or Salvage of Used Parts".
Your Cat dealer can provide these services and components. Your Cat dealer can ensure that the components are operating within the appropriate specifications.
The use of out-of-spec parts will cause unscheduled downtime and/or costly repairs.
Unit Injectors
Replace the unit injectors. Consult your Cat dealer about exchanging the unit injectors. Your Cat dealer can provide these services and components.
The wear of unit injectors is affected by the following considerations:
• Quality of the fuel
• Quality of the filtration of the fuel
The wear of the unit injectors can result in elevated levels of exhaust emissions and/or poor engine performance. The misfire of a single cylinder is not typically attributed to normal wear. This condition can be repaired by replacing the faulty unit injector.
The following lists of circumstances indicate that the unit injectors should be inspected more frequently:
• Use of fuels that are not recommended in this Operation and Maintenance Manual, "Fluid Recommendations"
• Extreme ambient temperatures that reduce the ability of the fuel to provide lubrication
• Frequent plugging of the fuel filters
• Insufficient maintenance of the fuel tank or the fuel storage tank that can allow excessive water, sediment, and other foreign matter.
• Insufficient maintenance of the fuel filters
Oil Suction Screen
Clean the oil suction screen after the oil has been drained.
Note: Approximately 1 L (1 qt) of oil will remain in the housing after the sump has been drained. This oil will pour out of the housing when cover (1) is removed. Prepare to catch the oil in a pan. Clean up any spilled oil with absorbent towels or pillows. DO NOT use absorbent particles to clean up the oil.
1. Remove the screen assembly according to the instructions in the Service Manual, "Disassembly and Assembly" module. Discard the used O-ring seals.
2. Wash the screen assembly in clean nonflammable solvent. Allow the screen assembly to dry before installation.
3. Remove side covers to gain access to the sump. Clean the bottom of the sump with absorbent towels or pillows. When the bottom of the sump is clean, install the side covers.
4. Inspect the screen assembly for good condition. Obtain a new screen assembly, if necessary. Install the screen assembly. Install new O-ring seals.
Replacement of Components
Replace the following components during the top end overhaul:
Inspection, Reconditioning, or Exchanging of Components
Inspect the following components according to the instructions that are in Caterpillar reusability publications. Refer to Guidelines for Reusable Parts and Salvage Operations, SEBF8029, "Index of Publications on Reusability or Salvage of Used Parts".
Recondition the worn components or exchange the components, if necessary. Your Cat dealer can provide these services and components.
Inspect the following components according to the instructions that are in Caterpillar reusability publications. Refer to Guidelines for Reusable Parts and Salvage Operations, SEBF8029, "Index of Publications on Reusability or Salvage of Used Parts".
• Aftercooler core
• Camshaft
• Crankshaft
• Driven equipment (alignment)
• Engine control module
• Exhaust bellow shields
• Oil suction screen
Note: Inspect only two of the components from each cylinder bank. Inspecting only two components will provide an adequate example of the condition of the other components.
Inspect and Lubricate
Inspect and lubricate the following (If Equipped):
• Duplex oil control valve linkage
Copyright 1993 - 2024 Caterpillar Inc. Wed Oct 23 08:00:44 UTC+0400 2024 All Rights Reserved. Private Network For SIS Licensees.
