Scribd
Upload
23 views

code 2

What is the best way

Uploaded by

h210595v
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
23 views

code 2

What is the best way

Uploaded by

h210595v
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

Certainly!

Below is a sample code in MikroC for interfacing the PIC16F877A with an LCD, MAX30100, and
HC-05 Bluetooth module. The code initializes UART for Bluetooth communication, I2C for the MAX30100
sensor, and SPI if needed in the future. This example will demonstrate how to read data from the
MAX30100 and send it via Bluetooth.

Before running the code, ensure that you have configured the proper connections for each component
in your Proteus simulation, and adjust the configuration bits in MikroC according to your hardware
setup.

Here's a sample code:

```c

// Include necessary libraries

#include <stdint.h>

#include <built_in.h>

// Define I2C and UART settings

#define MAX30100_ADDRESS 0x57

sbit LCD_RS at RA0_bit;

sbit LCD_EN at RA1_bit;

sbit LCD_D4 at RA2_bit;

sbit LCD_D5 at RA3_bit;

sbit LCD_D6 at RA4_bit;

sbit LCD_D7 at RA5_bit;

sbit LCD_RS_Direction at TRISA0_bit;


sbit LCD_EN_Direction at TRISA1_bit;

sbit LCD_D4_Direction at TRISA2_bit;

sbit LCD_D5_Direction at TRISA3_bit;

sbit LCD_D6_Direction at TRISA4_bit;

sbit LCD_D7_Direction at TRISA5_bit;

// Function Prototypes

void I2C_Init();

uint8_t I2C_Read(uint8_t address);

void I2C_Write(uint8_t address, uint8_t data);

void Bluetooth_Init();

void Bluetooth_Send(const char* data);

void MAX30100_Init();

void MAX30100_Read(uint8_t *heartRate, uint8_t *spo2);

// main function

void main() {

char buf[20];

uint8_t heartRate, spo2;

// Initialize modules

LCD_Init();

Bluetooth_Init();

I2C_Init();

MAX30100_Init();
// Main loop

while (1) {

// Read heart rate and SPO2 from MAX30100

MAX30100_Read(&heartRate, &spo2);

// Display on LCD

Lcd_Out(1, 1, "HR:");

Lcd_Chr(1, 4, heartRate + '0'); // Convert to ASCII

Lcd_Out(2, 1, "SpO2:");

Lcd_Chr(2, 6, spo2 + '0'); // Convert to ASCII

// Send data over Bluetooth

sprintf(buf, "HR:%d SpO2:%d\r\n", heartRate, spo2);

Bluetooth_Send(buf);

// Delay for a while

Delay_ms(1000);

// Initialization functions

void I2C_Init() {

I2C1_Init(100000); // Initialize I2C at 100kHz

}
void Bluetooth_Init() {

// Initialize UART for Bluetooth

UART1_Init(9600);

void MAX30100_Init() {

// Initialize MAX30100 sensor

I2C_Write(MAX30100_ADDRESS, 0x06); // Example register for configuration

// Add necessary initialization for MAX30100

// Function to read from MAX30100

void MAX30100_Read(uint8_t *heartRate, uint8_t *spo2) {

*heartRate = I2C_Read(MAX30100_ADDRESS); // Replace with the actual register for heart rate

*spo2 = I2C_Read(MAX30100_ADDRESS); // Replace with the actual register for SpO2

// I2C Read and Write functions

uint8_t I2C_Read(uint8_t address) {

uint8_t data;

I2C1_Start();

I2C1_Write(address);

data = I2C1_Read(0); // Read data without ACK

I2C1_Stop();
return data;

void I2C_Write(uint8_t address, uint8_t data) {

I2C1_Start();

I2C1_Write(address);

I2C1_Write(data);

I2C1_Stop();

// Function to send data via Bluetooth

void Bluetooth_Send(const char* data) {

UART1_Write_Text(data);

```

### Notes:

1. **Include Libraries**: Ensure you have necessary libraries for I2C and UART communication.

2. **MAX30100**: The MAX30100 configuration registers and data reading part should be checked in
the MAX30100 datasheet for the correct register addresses.

3. **LCD Connections**: Ensure your LCD is connected correctly. The pins for RS, EN, D4-D7 are
assigned in the code.

4. **UART Configuration**: Make sure the method for sending text over UART (Bluetooth) is compatible
with your Mikroc libraries/functions.

5. **Delay**: Adjust the delay according to your application needs.

6. **Proteus Setup**: Make sure the microcontroller is set up correctly in Proteus and that the
connections match the code.
Using this code as a reference, you can adjust the implementation to meet the specific requirements of
your project.

You might also like