Jcb Tier 4 Troubleshooting Codes

Fault Codes Page 1 of 319
JCB EcoMAX Help Files
Fault Codes
Engine > Fault Codes
Click on the fault code to link devise specific information and fault finding procedure
Fault Code Background Information
Fault Codes
1. P0001
2. P0002
3. P0003
4. P0004
5. P0016
6. P0045
7. P006C
8. P007A
9. P007C
10. P007D
11. P0070
12. P0087
13. P0088
14. P0089
15. P008A
16. P0090
17. P0091
18. P0092
19. P0095
20. P0096
21. P0097
22. P0098
23. P0099
24. P00B7
25. P0100
26. P0101
27. P0102
28. P0103
29. P0105
file:///C:/Users/M%20L%20Engine/AppData/Local/Temp/~hh7A53.htm 10/8/2019
30. P0106
31. P0110
32. P0111
33. P0112
34. P0113
35. P0115
36. P0116
37. P0117
38. P0118
39. P0120
40. P0121
41. P0129
42. P0180
43. P0181
44. P0182
45. P0183
46. P0190
47. P0191
48. P0192
49. P0193
50. P0194
51. P0195
52. P0196
53. P0197
54. P0198
55. P0200
56. P0201
57. P0202
58. P0203
59. P0204
60. P0220
61. P0230
62. P0236
63. P0237
64. P0238
65. P0252
66. P0253
67. P0254
68. P0261
69. P0262
70. P0263
71. P0264
72. P0265
73. P0266
74. P0267
75. P0268
76. P0269
77. P0270
78. P0271
79. P0272
80. P029A
81. P029B
82. P029E
83. P029F
84. P02A2
85. P02A3
86. P02A6
87. P02A7
88. P02EE
89. P02EF
90. P02F0
91. P02F1
92. P0321
93. P0325
94. P0330
95. P0335
96. P0340
97. P0341
98. P0350
99. P0371
100. P0372
101. P0374
102. P0380
103. P0381
104. P0383
105. P0384
106. P0400
107. P0460
108. P0470
109. P0471
110. P0472
111. P0473
112. P0500
113. P0501
114. P0503
115. P0520
116. P0521
117. P0522
118. P0523
119. P0544
120. P0545
121. P0546
122. P0560
123. P0562
124. P0563
125. P0566
126. P0567
127. P0569
128. P0570
129. P0575
130. P0602
131. P0603
132. P0604
133. P0605
134. P0606
135. P060A
136. P060B
137. P060C
138. P0612
139. P0615
140. P0616
141. P0617
142. P062D
143. P062E
144. P062F
145. P0627
146. P0628
147. P0629
148. P0630
149. P0641
150. P0650
151. P0651
152. P0655
153. P0656
154. P0658
155. P0659
156. P0668
157. P0669
158. P0685
159. P0697
160. P06A7
161. P0715
162. P1101
163. P1102
164. P1103
165. P1104
166. P1105
167. P1106
168. P1107
169. P1108
170. P1109
171. P110A
172. P110B
173. P1400
174. P1401
175. P1402
176. P1500
177. P1501
178. P1503
179. P1504
180. P1506
181. P1509
182. P1602
183. P2000
184. P202A
185. P202B
186. P202C
187. P202E
188. P203B
189. P203F
190. P2043
191. P204B
192. P204C
193. P204D
194. P204F
195. P205B
196. P205C
197. P205D
198. P205E
199. P207F
200. P2080
201. P208A
202. P208B
203. P208C
204. P208D
205. P209F
206. P20A0
207. P20A1
208. P20A2
209. P20A3
210. P20AD
211. P20B5
212. P20B6
213. P20B7
214. P20B8
215. P20B9
216. P20BA
217. P20BB
218. P20BC
219. P20BD
220. P20BE
221. P20BF
222. P20C0
223. P20C1
224. P20C2
225. P20C3
226. P20C4
227. P20E8
228. P20E9
229. P20EA
230. P20EB
231. P2100
232. P2101
233. P2102
234. P2103
235. P2120
236. P2125
237. P2135
238. P2138
239. P2147
240. P2148
241. P219D
242. P219E
243. P219F
244. P21A9
245. P21AB
246. P2200
247. P2201
248. P2202
249. P2203
250. P2208
251. P2209
252. P2226
253. P2228
254. P2229
255. P2264
256. P2265
257. P2266
258. P2267
259. P2269
260. P2413
261. P2428
262. P242B
263. P242C
264. P242D
265. P2502
266. P250B
267. P250F
268. P256A
269. P256B
270. P256C
271. P256D
272. P2620
273. P2670
274. P2671
275. P2685
276. P2686
277. P2A00
278. P2A01
279. P2BA7
280. P2BA8
281. P2BA9
282. P2BAA
283. P2BAB
284. P2BAE
285. P3401
286. P3402
287. P3403
288. P3404
289. P3405
290. P3406
291. P3407
292. P3408
293. P3409
294. P3410
295. P3411
296. P3412
297. P3413
298. P3414
299. P3415
300. P3416
301. P3417
302. P3418
303. P3419
304. P3420
305. P3421
306. P3422
307. P3423
308. P3424
309. P3425
310. U0001
311. U0029
312. U0073
313. U0100
314. U0105
315. U010A
316. U010C
317. U010E
318. U0121
319. U0140
320. U0401
321. U040B
322. U040D
323. U040F
324. U059E
325. U059F
326. U3FFF
Fault Code Background Information
Engine > Fault Codes > Fault Code Background Information
Fault Code Structure

Fault Code Display
Failure Type Byte (FTB) Numbers
Fault Code Structure
The structure of fault codes, otherwise known as 'Diagnostic Trouble Codes' (DTC's) has been standardised to a
7 digit code for all on and off-highway machine and vehicle applications. The standard (referred to as J2012)
requires all fault codes to conform to the following structure.
1st character - defines the system on the vehicle (eg P = Powertrain, C = Chassis, U = Network)
2nd and 3rd characters - defines the sub-system (eg transmission, CAN network, brakes etc)
4th and 5th characters - specifies the particular component, circuit or fault (eg starter relay)
6th and 7th characters - referred to as the 'Failure Type Byte' (FTB) which indicates the particular failure (eg 11 =
short circuit to ground). See FTB Numbers below for a full list.
Some specific fault codes are defined by international standard, while other codes may be defined by individual
vehicle manufacturers.
Fault Code Display
Depending on the machine specification fault codes recorded by the engine ECU can be accessed and displayed
in several ways:
CAN Enabled Display
The machine may be equipped with a CAN enabled display. Such a display will be capable of displaying all
recorded codes, for example P0047. All logged codes will be displayed. The operator may also have a facility to
erase the fault code log. See the applicable machine documentation for further information.
CAN BUS Connected Computer
Error codes logged can be accessed via a suitable laptop computer running the applicable diagnostics software,
JCB 444 Engine Diagnostics for example. The computer must be connected to the machine CAN BUS socket
using a data link adapter (DLA). Once connected all recorded codes can be displayed. The engineer also has a
facility to erase the fault code log.
Failure Type Byte (FTB) Numbers
00 No sub type information
02 General signal failure
04 System internal failure (ECU)
07 Mechanical failure
05 System programming failure
09 Component failure
11 Short Circuit to Ground (SC2G)
12 Short Circuit to Battery (SC2VBAT)
13 Open Circuit (OC)
16 Circuit voltage below threshold
17 Circuit voltage above threshold
18 Circuit current below threshold
19 Circuit current above threshold
1A Circuit resistance above threshold
1B Circuit resistance below threshold
1C Circuit voltage out of range
1F Circuit intermittent
23 Signal stuck low
24 Signal stuck high
26 Signal rate of change below threshold
27 Signal rate of change above threshold
29 Signal invalid
2F Signal erratic
31 No Signal (lost/missing)
36 Signal frequency too low
37 Signal frequency too high
38 Signal frequency incorrect
45 Programme memory failure
46 Calibration / Parameter memory failure
47 Watchdog / micro-controller / microprocessor failure
4B Over temperature
54 Missing Calibration
64 Signal plausibility failure
62 Signal compare failure
71 Actuator stuck
72 Actuator stuck open
73 Actuator stuck closed
81 Received Network Data in Error
85 Signal above allowable range
86 CAN Signal invalid
87 Missing Message
88 BUS Off
9A Component or System Operating Conditions
92 Performance or incorrect operation
96 Component or Internal Failure
97 Component or System Operation Obstructed or Blocked
98 Component of System Over Temperature
P0001
Engine > Fault Codes > P0001
Fault Code Description

Information
Service Procedure
Related Fault Codes

Fuel volume regulator control circuit/open
Open circuit on the inlet metering valve
Information
ECU Engine ECU.
Effect Reduced Power Mode (Engine Derate) torque reduction.
Possible Cause Damaged harness or harness connectors.
Service Procedure
Important: Stop the engine and let it cool before you start work. Do not start the engine during the service
procedures. (SN0001)
1. Check for any damaged or loose machine earths and connector pins as well as debris or water inside the
connector terminals. This may be as a consequence of pressure washing the engine, loose connectors or
poor connector sealing.
1. Check the harness is not damaged and is routed correctly.
2. Complete the testing procedure described in the component page Inlet metering valve.
Related Fault FTB Codes

P0001-13 Open circuit
This topic last edited on 27/05/2016
P0002

Information
Service Procedure

Fuel volume regulator control circuit range/performance
Circuit range fault on the inlet metering valve
Information
ECU Engine ECU.
Service Procedure

P0002-12 Short circuit to battery (SC2VBAT)
P0002-11 Short circuit to ground (SC2G)
P0002-00 No sub type information.
P0003

Information
Service Procedure

Fuel volume regulator control circuit low
Fault on the Inlet Metering Valve (IMV).
Information
ECU Engine ECU.

Faulty component.
Service Procedure

P0003-13 Open circuit (OC)
P0003-19 Circuit current above threshold
P0003-0 No sub type information
P0004

Information
Service Procedure

Fuel volume regulator control circuit high
Open circuit on the Inlet Metering Valve (IMV).
Information
ECU Engine ECU.
Service Procedure

P0004-12 Short Circuit To Battery (SC2VBAT)
P0016

Information
Service Procedure
Camshaft position correlation

Signal fault on the camshaft position sensor.
Information
ECU Engine ECU.
Effect

Faulty component.
Service Procedure
3. Complete the testing procedure described in the component page camshaft position sensor.

P0016-2F Signal erratic.
P0045

Information
Service Procedure

Turbocharger/supercharger boost control "A" circuit/open
Fault on the variable geometry turbocharger (VGT).
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page Variable Geometry Turbocharger (VGT).

P006C
Engine > Fault Codes > P006C

Information
Service Procedure

MAP - Turbocharger/supercharger inlet pressure correlation
Fault on the TMAP sensor.
Information
ECU Engine ECU.
Effect
Possible Cause Damaged harness or harness connectors..
Service Procedure
3. Complete the testing procedure described in the component page intake temperature and manifold absolute
pressure (TMAP) sensor.

P006C-11 Short circuit to ground (SC2G).
P006C-12 Short circuit to battery (SC2VBAT).
P007A
Engine > Fault Codes > P007A

Information
Service Procedure

Charge air cooler temperature sensor circuit
Fault with the charge air temperature circuit.
Information
ECU Engine ECU.
Service Procedure
3. Complete the testing procedure described in the component page charge air cooler/intercooler outlet
temperature sensor.

P007A-00 No sub type information
P007C

Information
Service Procedure

Charge air cooler temperature sensor circuit low
Fault with the charge air cooler temperature sensor circuit.
Information
ECU Engine ECU.
Service Procedure
temperature sensor.

P007C-23 Signal stuck low
P007D
Engine > Fault Codes > P007D

Information
Service Procedure

Charge air cooler temperature sensor circuit high
Fault with the charge air cooler temperature sensor circuit.
Information
ECU Engine ECU.
Possible Cause Damaged harness or harness connectors..
Service Procedure
temperature sensor.

P007D-24 Signal stuck high
P0070

Information
Service Procedure

Type text here
Information
ECU Aftertreatment ECU.
Effect Reduced Power Mode (Engine Derate).
Possible Cause Damaged harness or harness connector.

Invalid data from ECU (other fault codes present).
Service Procedure
3. Complete the testing procedure described in the component page CAN communications error.

P0070-81 Invalid signal data received (CAN BUS message error from engine ECU)
P0070-87 Missing CAN message from ECU
P0087

Information
Service Procedure

Fuel rail/system pressure - too low
The fuel system pressure is too low.
Information
ECU Engine ECU.
Effect Reduced Power Mode (Engine Derate) torque reduction and delayed stop.
Possible Cause Fuel pipe restriction.

Fuel leak.
Damaged harness or harness connector.
Faulty sensor.
Faulty fuel pump.
Service Procedure
1. Check that the fuel tank has sufficient fuel in it.
2. Check the fuel lift pump flow, If the lift pump is inoperative check the lift pump relay.
3. If the fuel lift pump is still inoperative check the voltage, current and resistance at the pump.
Machine Minimum Maximum Minimum Maximum Minimum Maximum

Voltage Voltage Voltage Resistance Resistance Current Draw Current Draw
(Ohms) (Ohms) (Amps) (Amps)
12V 8V 16V 0.8 1.5 4 8
24V 20V 30V 4.9 5.7 4 5.5
4. Check for correct hose routing, restrictions or leaks from the fuel pipes. Make sure that fuel pipes have not
been trapped under other assemblies (e.g. cooling pack, hydraulic system components).
5. Replace fuel filters.
6. Check the lift pump is delivering sufficient fuel. Refer to fuel lift pump test.

P0087-24 Signal stuck high.
P0087-64 Signal plausibility failure.
P0088

Information
Service Procedure

Fuel rail/system pressure - too high
The fuel system pressure is too high.
Information
ECU Engine ECU.
Possible Cause Damaged sensor.

Blocked fuel return pipe.
Damaged harness or connector.
Service Procedure
1. Complete sensor checks and measurements for the IMV, common rail fuel pressure sensor and high
pressure fuel valve.

2. Check fuel return pipes are not trapped or blocked.

P0088-23 Signal stuck low
P0089

Information
Service Procedure

Fuel pressure regulator 1 performance
Fuel rail pressure fault with the high pressure fuel valve.
Information
ECU Engine ECU
Service Procedure
3. Complete the testing procedure described in the component page high pressure fuel valve.

P0089-11 Short Circuit To Ground (SC2G)
P008A

Information
Service Procedure

Low pressure fuel system pressure - too low
Fault with the fuel injector.
Information
ECU Engine ECU
Effect
Possible Cause Damaged harness or harness connector, faulty injector.
Service Procedure
3. Complete the testing procedure described in the component page fuel injector.
P0090

Information
Service Procedure

Fuel pressure regulator 1 control circuit open
Fault with the high pressure fuel valve (HPV).
Information
ECU Engine ECU
Effect
Service Procedure
3. Complete the testing procedure described in the component page high pressure fuel valve (HPV).

P0090-00 no sub type information
P0091

Information
Service Procedure

Fuel pressure regulator 1 control circuit low
Information
ECU Engine ECU
Effect
Service Procedure

P0092

Information
Service Procedure

Fuel pressure regulator 1 control circuit high
Information
ECU Engine ECU
Effect
Possible Cause Damaged harness or harness connectors, faulty HPV.
Service Procedure

P0092 Check HPV regulation control trim high
P0092 Check HPV hardware current control trim high
P0092 HPV current feedback high fault detected
P0092 HPV driver in ECU short circuit to battery voltage (SC2VBATT) fault is detected
P0095

Information
Service Procedure

Intake air temperature sensor 2 circuit
Fault with the temperature and manifold absolute pressure (TMAP) sensor.
Information
ECU Engine ECU
Effect
Service Procedure
3. Complete the testing procedure described in the component page temperature and manifold pressure
(TMAP) sensor.

P0095-00 No sub type informtion
P0096

Information
Service Procedure

Intake air temperature sensor 2 circuit range/performance
Information
ECU Engine ECU
Effect
Possible Cause Damaged harness or harness connectors, faulty TMAP sensor.
Service Procedure
(TMAP) sensor.

P0096-2F Signal erratic
P0097

Information
Service Procedure

Intake air temperature sensor 2 circuit low
Information
ECU Engine ECU
Effect
Possible Cause Damaged harness or harness connector, faulty TMAP sensor
Service Procedure
(TMAP) sensor.

P0098

Information
Service Procedure

Intake air temperature sensor 2 circuit high
Information
ECU Engine ECU
Service Procedure
(TMAP) sensor.

P0098-24 Signal stuck high
P0099

Information
Service Procedure

Intake air temperature sensor 2 circuit intermittent/erratic
Fault with the intake temperature and manifold absolute pressure (TMAP) sensor circuit.
Information
ECU Engine ECU
Effect
Service Procedure
(TMAP) sensor.

P00B7
Engine > Fault Codes > P00B7

Information
Service Procedure

CAN BUS message error for coolant sensor from Engine ECU
Missing CAN message error for coolant sensor from the ECU.
Information
ECU Engine ECU
Effect Error code.
Possible Cause Damaged harness or harness connectors, faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component page CAN communication error.

P00B7-87 Missing CAN message (CAN BUS message error for coolant sensor from engine ECU)
P0100

Information
Service Procedure

Mass or volume air flow "A" circuit
Fault with the temperature mass air flow (TMAF) sensor.
Information
ECU Engine ECU
Effect
Possible Cause Damaged harness or harness connector, faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component page temperature mass air flow (TMAF) sensor.

P0101

Information
Service Procedure

Mass or volume air flow "A" circuit range/performance
Fault on the temperature mass air flow (TMAF) sensor circuit.
Information
ECU Engine ECU.
Effect
Service Procedure

P0102

Information
Service Procedure

Mass or volume air flow "A" circuit low
Information
ECU Engine ECU.
Effect
Service Procedure

P0102-11 Short Circuit To Ground (SC2G)
P0103

Information
Service Procedure

Mass or volume air flow "A" circuit high
Information
ECU Engine ECU.
Effect
Service Procedure

P0102-12 Short Circuit To Battery (SC2VBAT)
P0105

Information
Service Procedure

Manifold absolute pressure/barometric pressure circuit
Fault on the temperature and manifold absolute pressure (TMAP) sensor.
Information
ECU Engine ECU.
Effect
Service Procedure

P0106

Information
Service Procedure

Manifold absolute pressure/barometric pressure circuit range/performance
Fault on the temperature and manifold absolute pressure (TMAP) sensor.
Information
ECU Engine ECU.
Effect
Service Procedure

P0110

Information
Service Procedure

Intake air temperature sensor 1 circuit
Fault on the temperature mass air flow (TMAF) sensor.
Information
ECU Engine ECU.
Effect
Possible Cause Damaged harness or harness connectors,

faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component page intake temperature mass air flow (TMAF)
sensor.

P0111

Information
Service Procedure

Intake air temperature sensor 1 circuit low
Information
ECU Engine ECU.
Effect
Service Procedure
sensor.

P0111-64 Signal plausibility failure
P0112

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure
sensor.

P0113

Information
Service Procedure

Information
ECU Engine ECU.
Effect

Faulty sensor.
Service Procedure
sensor.

P0113-24 Signal stuck high (open circuit)
P0115

Information
Service Procedure

Engine coolant temperature sensor 1 circuit
Fault on the coolant sensor circuit.
Information
ECU Engine ECU.
Effect
Possible Cause damaged harness or harness connectors.
Service Procedure
3. Complete the testing procedure described in the component page coolant temperature sensor.
P0115-15 Short circuit to battery (SC2VBAT) or open circuit
P0116

Information
Service Procedure

Engine coolant temperature sensor 1 circuit range/performance
Information
ECU Engine ECU.
Effect
Service Procedure

P0117

Information
Service Procedure

Engine coolant temperature sensor 1 circuit low
Information
ECU Engine ECU.
Effect
Service Procedure

P0118

Information
Service Procedure

Engine coolant temperature sensor 1 circuit high
Information
ECU Engine ECU.
Effect
Service Procedure

P0118-12 Short circuit to ground (SC2VBAT)
P0120

Information
Service Procedure

Throttle/pedal position sensor/switch "A" circuit
Fault on the throttle pedal switch.
Information
ECU Engine ECU.
Effect
Possible Cause Damaged Harness or harness connectors, faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component page throttle position sensor.

P0121

Information
Service Procedure

Throttle/pedal position sensor/switch "A" circuit range/performance
Fault on the throttle pedal switch.
Information
ECU Engine ECU.
Effect
Possible Cause Damaged Harness or harness connectors, faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component page throttle position sensor.

P0129

Information
Service Procedure

Barometric pressure signal from engine ECU
CAN BUS message error for barometric pressure.
Information
ECU Engine ECU.
Effect Error code.
Possible Cause Damaged Harness or harness connector, faulty sensor.
Service Procedure

P0129-87 Missing CAN message from engine ECU (Erroneous signal for barometric pressure)
P0180

Information
Service Procedure

Fuel temperature sensor "A" circuit
Fault on the fuel temperature sensor circuit.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page fuel temperature sensor.

P0181

Information
Service Procedure

Fuel Temperature
Erroneous signal for fuel temperature.
Information
ECU Engine ECU.
Effect

Faulty sensor.
Service Procedure

Fault Description
Code
P0181-27 Signal rate of change above threshold (fuel temperature sensor gradient fault)
P0181-87 Missing CAN message from engine ECU (CAN bus message error for fuel temperature from engine
ECU)
P0182

Information
Service Procedure

Fuel temperature sensor "A" circuit low
Information
ECU Engine ECU.
Effect
Service Procedure


P0183

Information
Service Procedure

Fuel temperature sensor "A" circuit high
Information
ECU Engine ECU.
Effect
Service Procedure

P0183-12 Short circuit to bettery (SC2VBAT)
P0190

Information
Service Procedure

Fuel rail pressure sensor "A" circuit
Fault on the common rail fuel pressure sensor.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page common rail fuel pressure sensor.

P0191

Information
Service Procedure

Fuel rail pressure sensor "A" circuit range/performance
Information
ECU Engine ECU.
Effect
Service Procedure

P0192

Information
Service Procedure

Fuel rail pressure sensor "A" circuit low
Information
ECU Engine ECU.
Effect
Service Procedure

P0193

Information
Service Procedure

Fuel rail pressure sensor "A" circuit high
Information
ECU Engine ECU.
Effect
Service Procedure

P0194

Information
Service Procedure

Fuel rail pressure sensor "A" circuit intermittent/erratic
Information
ECU Engine ECU.
Effect
Service Procedure

P0195

Information
Service Procedure

Engine oil temperature sensor circuit
Fault on the oil temperature sensor circuit.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page oil temperature sensor.

P0196

Information
Service Procedure

Engine oil temperature sensor range/performance
Missing CAN message.
Information
ECU Engine ECU/ aftertreatment system ECU.
Effect Error code.

Faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component pages oil temperature sensor and CAN
communication error.

Fault Description
Code
P0196-27 Signal rate of change above threshold - Engine ECU (oil temperature sensor signal gradient fault)
P0196-64 Signal plausibility failure - Engine ECU (Oil temperature sensor signal gradient fault)
P0196-87 Missing CAN message from engine ECU - Aftertreatment DCU (CAN BUS message error for oil
temperature from engine ECU)
P0197

Information
Service Procedure

Engine oil temperature sensor circuit low
Information
ECU Engine ECU.
Effect
Service Procedure

P0198

Information
Service Procedure

Engine oil temperature sensor circuit high
Information
ECU Engine ECU.
Effect
Service Procedure

P0200

Information
Service Procedure

Injector circuit/open
Open circuit on the fuel injector.
Information
ECU Engine ECU.
Effect
Service Procedure

P0201

Information
Service Procedure

Injector circuit/open - cylinder 1
Information
ECU Engine ECU.

Engine fails to start or stops if running.
Service Procedure

P0202

Information
Service Procedure

Information
ECU Engine ECU.

Engine fails to start or stops if running.
Service Procedure

P0203

Information
Service Procedure

Information
ECU Engine ECU.

Engine fails to start or stops if running
Service Procedure

P0204

Information
Service Procedure

Information
ECU Engine ECU.

Engine fails to start or stops if running
Service Procedure

P0220

Information
Service Procedure

Throttle/pedal position sensor/switch "B" circuit
Fault on the foot throttle position sensor.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page foot throttle position sensor.

P0230

Information
Service Procedure

Fuel pump primary circuit
Fault on the low pressure fuel supply circuit.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page fuel lift pump relay.

P0236

Information
Service Procedure

Turbocharger/Supercharger Boost Sensor "A" Circuit Range/Performance
Fault on the TMAP sensor.
Information
ECU Engine ECU.
Effect Torque reduction.
Possible Cause Faulty TMAP Sensor.

Damaged harness or harness connectors.
Service Procedure
3. Complete the testing procedure described in the component page TMAP sensor.

P0236-11 Short circuit to ground (SC2G).
P0236-12 Short circuit to battery (SC2VBAT).
P0236-16 Circuit voltage below threshold.
P0237

Information
Service Procedure

Turbocharger/Supercharger Boost Sensor "A" Circuit Low
Boost Pressure signal too low.
Information
ECU Engine ECU.
Possible Cause Faulty TMAP sensor.

Inlet air leak.
Faulty turbocharger.
Service Procedure
3. Complete the testing procedure described in the component page variable geometry turbocharger (VGT).

P0237-11 Short circuit to ground (SC2G).
P0237-16 Circuit voltage below threshold.
P0237-17 Circuit voltage above threshold.
P0237-21 Data drifted low.
P0237-23 Signal stuck low.
P0238
Information
Service Procedure

Turbocharger/Supercharger Boost Sensor "A" Circuit High
Boost Pressure signal too high.
Information
ECU Engine ECU.
Possible Cause Faulty TMAP sensor.

Faulty turbocharger.
Service Procedure
3. Complete the testing procedure described in the component page variable geometry turbocharger (VGT).

P0238-12 Short circuit to battery (SC2VBAT).
P0238-17 Circuit voltage above threshold
P0238-22 Data drifted high.
P0238-24 Signal stuck high.
P0252

Information
Service Procedure

Injection pump fuel metering control "A" range/performance (cam/rotor/injector)
Fault on the inlet metering valve (IMV).
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page inlet metering valve.

P0253

Information
Service Procedure

Low Fuel Flow - IMV
Insufficient fuel flow from the low pressure fuel system (tank, low pressure pump,filters) or IMV electrical fault.
Information
ECU Engine ECU.
Effect
Possible Cause Fuel pipe restriction.

Fuel leak.
Faulty fuel pump.
Faulty sensor.
Service Procedure
1. Check that the fuel tank has sufficient fuel in it.
2. Complete the injector leak back test testing procedure described in fuel system diagnostic test.
3. Check the fuel lift pump flow, If the lift pump is inoperative check the lift pump relay.
4. If the fuel lift pump is still inoperative check the voltage, current and resistance at the pump.
Machine Minimum Maximum Minimum Maximum Minimum Maximum

Voltage Voltage Voltage Resistance Resistance Current Draw Current Draw
(Ohms) (Ohms) (Amps) (Amps)
12V 8V 16V 0.8 1.5 4 8
24V 20V 30V 4.9 5.7 4 5.5
5. Check for correct hose routing, restrictions or leaks from the fuel pipes. Make sure that fuel pipes have not
been trapped under other assemblies (e.g. cooling pack, hydraulic system components).
6. Replace fuel filters.
7. Check the lift pump is delivering sufficient fuel. Refer to fuel lift pump test.
8. Check the low pressure fuel system for restrictions such as: Blockages, damaged hoses, blocked fuel filters,
damaged in tank fuel pick up.
9. Check high pressure fuel pump, common rail and injector leak off and repair as required.

P0254

Information
Service Procedure

Injection pump fuel metering control "A" high (cam/rotor/injector)
Fault on the inlet metering valve (IMV).
Information
ECU Engine ECU.
Effect
Service Procedure

P0261

Information
Service Procedure

Cylinder 1 injector circuit Low
Fault on the fuel injector.
Information
ECU Engine ECU.
Effect
Service Procedure

P0262

Information
Service Procedure

Cylinder 1 injector circuit high
Information
ECU Engine ECU.
Effect
Service Procedure

P0263

Information
Service Procedure

Cylinder 1 contribution/balance
Information
ECU Engine ECU.
Effect
Service Procedure

P0264

Information
Service Procedure

Cylinder 2 injector circuit low
Information
ECU Engine ECU.
Effect
Service Procedure

P0265

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P0266

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P0267

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P0268

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P0269

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P0270

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P0271

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P0272

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P029A

Information
Service Procedure

Cylinder 1 fuel trim at maximum limit
Information
ECU Engine ECU.
Effect
Service Procedure

P029B
Engine > Fault Codes > P029B

Information
Service Procedure

Cylinder 1 fuel trim at minimum limit
Information
ECU Engine ECU.
Effect
Service Procedure

P029B-00 No sub type information
P029E
Engine > Fault Codes > P029E

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P029E-00 No sub type information
P029F
Engine > Fault Codes > P029F

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P029F-00 No sub type information
P02A2
Engine > Fault Codes > P02A2

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P02A2-00 No sub type information
P02A3

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P02A6

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P02A7

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P02EE
Engine > Fault Codes > P02EE

Information
Service Procedure

Cylinder 1 injector circuit range/performance
Information
ECU Engine ECU.
Effect
Service Procedure

P02EE-00 No sub type information
P02EF
Engine > Fault Codes > P02EF

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P02EF-00 No sub type information
P02F0
Engine > Fault Codes > P02F0

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P02F0-00 No sub type information
P02F1
Engine > Fault Codes > P02F1

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P02F1-00 No sub type information
P0321

Information
Service Procedure

Engine Speed
Erroneous signal for engine speed.
Information
ECU Engine ECU.
Effect Error code and inducement.
Service Procedure

Fault Description
Code
P0321-87 Missing message CAN message from ECU (CAN BUS message for engine speed from engine
ECU)
P0325

Information
Service Procedure

Knock Sensor 1 Circuit
Fault on the knock sensor circuit.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page knock sensor.

P0330

Information
Service Procedure

Knock Sensor 2 Circuit
Fault on the knock sensor circuit.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page knock sensor.

P0335

Information
Service Procedure

Crankshaft Position Sensor "A" Circuit
Fault on the crankshaft position sensor.
Information
ECU Engine ECU.
Effect

Faulty crankshaft position sensor.
Excessive engine speed (P0335-85), e.g. machine in over-run traveling
downhill in a low gear and/or with the torque convertor lock up engaged.
If the fault occurrence is low, it could be generated as a result of a sudden
engine stall (P0335-31).
Service Procedure
1. Disconnect the electrical connector from the engine ECU.
2. Make sure that the is correctly installed and is not damaged or corroded.
3. Disconnect the electrical connector from the crankshaft sensor.
4. Use a multi-meter to test for wire continuity (open circuits) between the relevant connector pins. Refer to the
component help page crankshaft position sensor.

P0335-00 Crank sensor fault （No signal）

P0335-31 No signal (lost/missing)
P0335-85 Crank signal overspeed fault
P0340

Information
Service Procedure

Camshaft position sensor "A" circuit
Fault on the camshaft position sensor.
Information
ECU Engine ECU.
Effect
Service Procedure

P0341

Information
Service Procedure

Camshaft position sensor "A" circuit range/performance
Fault on the camshaft position sensor.
Information
ECU Engine ECU.
Effect

Faulty sensor.
Sudden or harsh engine stop.
Service Procedure
1. If the engine has been stalled or subject to a sudden stop this fault code can be triggered. The fault code can
be cleared and should not return when the engine is started.

P0341-31 No Signal (lost/missing)

Information
Service Procedure

Monitoring for system protection based on ignition switch input
This fault code indicates an error with the monitoring for system protection based on T15 status.
Information
ECU Aftertreatment ECU.
Effect Error code.
Possible Cause Damaged harness or harness connector, out of date ECU software.
Service Procedure
3. Make sure that the ECU software is up to date. If it is not refer to Re-flashing an ECU.
4. Complete the testing procedure described in the component page aftertreatment ECU.

P0350-02 General signal failure
P0371

Information
Service Procedure
Timing reference high resolution signal "A" too many pulses
Fault on the crankshaft position sensor circuit.
Information
ECU Engine ECU.
Effect
Possible Cause Faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component page crankshaft position sensor.

P0372

Information
Service Procedure

Timing reference high resolution signal "A" too few pulses
Information
ECU Engine ECU.
Service Procedure

P0372-31 Elapsed time between CPS events is too high
P0374

Information
Service Procedure

Timing reference high resolution signal "A" no pulses
Information
ECU Engine ECU.
Effect
Service Procedure

P0380

Information
Service Procedure

Glow plug/heater circuit "A"
Fault on the grid heater relay control.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page grid heater.
P0381

Information
Service Procedure

Glow plug/heater indicator circuit
Information
ECU Engine ECU.
Effect
Service Procedure

P0383

Information
Service Procedure

Glow plug control module control circuit low
Information
ECU Engine ECU.
Effect
Service Procedure

P0384

Information
Service Procedure

Glow plug control module control circuit high
Information
ECU Engine ECU.
Effect

Faulty sensor.
Service Procedure

P0400

Information
Service Procedure

Exhaust gas recirculation "A" flow
Fault on the exhaust gas recirculation (EGR) control system.
Information
ECU Engine ECU.
Possible Cause Blocked EGR valve.

Blocked EGR mixer tube or inlet manifold.
Blocked EGR cooler.
Boost leak.
EGR system exhaust gas leak.
Blocked exhaust gas pressure sensor or tube.
Faulty or missing exhaust restrictor.
Faulty or missing intake restrictor.
Faulty mass airflow sensor, damaged airbox or air intake hose.
Faulty intake manifold pressure sensor.
Missing CAN termination resistor.
Service Procedure
1. If P0400-00 is present along with either U040B or U040D, refer to P0400-00 CANBUS Test.
2. If P0400-00 is present on its own perform a visual check of the system by following the P0400-00 Visual
Checklist. This checklist must be complete before moving to the next step to rule out other root causes.
3. If P0400-00 is still present continue to P0400-00 Test page.

P0400-00 EGR Flow limit reached OR EGR CAN communication error (T4i engines only)
U040B Fault on the CAN communication network
U040D Fault detected with the VGT electrical or mechanical system
P0460

Information
Service Procedure

Low fuel Level
Information
ECU Engine ECU.
Effect Fuel light on.
Possible Cause Low fuel Level.

Damaged Harness or harness connector.
Service Procedure
1. Check the fuel level, fill as required.

P0460-7B Fuel tank empty (<6% full)
P0460-21 Fuel tank level low (<12% full)
P0470

Information
Service Procedure

Exhaust pressure sensor "A" circuit
Fault on the exhaust manifold pressure sensor.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page exhaust manifold pressure sensor.

P0471

Information
Service Procedure
Exhaust pressure sensor "A" circuit range/performance

Information
ECU Engine ECU.
Effect
Service Procedure

P0472

Information
Service Procedure

Exhaust pressure sensor "A" circuit low
Information
ECU Engine ECU.
Effect
Service Procedure

P0473

Information
Service Procedure

Exhaust pressure sensor "A" circuit high
Information
ECU Engine ECU.
Effect
Service Procedure

P0500

Information
Service Procedure

Vehicle speed sensor "A"
Fault on the vehicle speed sensor input.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page vehicle speed sensor.

This topic last editedA on 08/09/2015
P0501

Information
Service Procedure

Vehicle speed sensor "A" range/performance
Information
ECU Engine ECU.
Effect
Service Procedure

P0503

Information
Service Procedure

Vehicle speed sensor "A" intermittent/erratic/high
Information
ECU Engine ECU.
Effect
Service Procedure

P0520

Information
Service Procedure

Low oil pressure lamp drive circuit
Fault on the circuit used to control the low oil pressure light.
Information
ECU Engine ECU.
Effect

Faulty low oil pressure warning lamp.
Service Procedure
1. Check the low oil pressure lamp.
4. Check the ignition circuit and fuses.

P0521

Information
Service Procedure

Engine oil pressure sensor/switch range/performance
Fault on the oil pressure switch circuit.
Information
ECU Engine ECU
Effect
Possible Cause Faulty oil pressure switch.

Service Procedure
3. Complete the testing procedure described in the component page oil pressure switch.

P0522

Information
Service Procedure

High oil pressure (engine running/engine stopped)
Unexpected high oil pressure signal received either when the engine is stopped or while the engine is running.
Information
ECU Engine ECU.
Effect
Service Procedure

P0523

Information
Service Procedure

Low oil pressure during engine running
Fault on the circuit used to control the low oil pressure light.
Information
ECU Engine ECU.
Effect
Possible Cause Damaged harness or harness connector, faulty sensor, low engine oil
pressure.
Service Procedure

P0544

Information
Service Procedure

Exhaust gas temperature sensor circuit
Fault on the exhaust gas temperature sensor circuit.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page exhaust manifold temperature sensor.

P0545

Information
Service Procedure

Exhaust gas temperature sensor circuit low
Information
ECU Engine ECU.
Effect
Service Procedure

P0546

Information
Service Procedure

Exhaust gas temperature sensor circuit high
Information
ECU Engine ECU.
Effect
Service Procedure

P0560

Information
Service Procedure

System voltage
Fault with the battery voltage.
Information
ECU Engine ECU/aftertreatment ECU.
Effect
Possible Cause Damaged harness or harness connector, faulty or discharged battery.
Service Procedure
3. Complete the testing procedure described in the component page battery voltage fault.

P0562

Information
Service Procedure

System voltage low
Information
Effect
Possible Cause Damaged harness or harness connector, faulty or discharged battery.
Service Procedure

P0562-02 General signal failure (fault due to low or high battery voltage supply to ECU)
P0562-16 Circuit voltage below threshold (Low battery voltage)
P0563

Information
Service Procedure

System voltage high
Information
Effect
Possible Cause Damaged harness or harness connector, faulty battery or over charged
battery.
Service Procedure

P0566

Information
Service Procedure

Cruise control "off" signal
Fault with the cruise control system.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page cruise control switch.

P0567

Information
Service Procedure

Cruise control "off" signal
Information
ECU Engine ECU.
Effect
Service Procedure

P0569

Information
Service Procedure

Cruise control "coast" signal
Information
ECU Engine ECU.
Effect
Service Procedure

P0570

Information
Service Procedure

Cruise control "accelerate" signal
Information
ECU Engine ECU.
Effect
Service Procedure

P0575

Information
Service Procedure

Cruise control input circuit
Information
ECU Engine ECU.
Effect
Service Procedure

P0602

Information
Service Procedure

Control module programming error
Fault with the engine electronic control unit (ECU).
Information
ECU Engine ECU.
Effect
Possible Cause Incorrect or out of date ECU software.
Service Procedure
1. Make sure that the ECU software is up to date. Refer to re-flashing an ECU.
2. Complete the testing procedure described in the component page engine ECU.

P0602-55 Out of calibration
P0603

Information
Service Procedure

Internal control module keep alive memory (KAM) error
Information
ECU Engine ECU.
Effect

Faulty ECU.
Service Procedure

P0603-2F no sub type information
P0604

Information
Service Procedure

Internal control module random access memory (RAM) error
Information
ECU Engine ECU.
Effect

Faulty ECU.
Service Procedure

P0604-2F signal erratic
P0605

Information
Service Procedure

Internal control module read only memory (ROM) error
Information
ECU Engine ECU.
Effect

Faulty ECU.
Service Procedure

P0605-2F signal erratic
P0606

Information
Service Procedure

Peripheral monitoring error on DCU
Fault with the peripheral monitoring function on the aftertreatment system electronic control unit (ECU).
Information
ECU Aftertreatment ECU and engine ECU.
Effect Error code.

Incorrect or out of date ECU software.
Service Procedure
4. Complete the testing procedure described in the component page aftertreatment system ECU.

P0606-02 General signal failure (peripheral monitoring error on DCU)
P0606-06 Algorithm based failure (functional safety fault)
P0606-49 Internal electronic failure (main CPU fault)
P0606-86 Signal invalid (functional safety fault)
P0606-87 Missing CAN message
P060A

Information
Service Procedure

Monitoring error on aftertreatment ECU - functional safety fault
Aftertreatment ECU has detected an error during a PostDrive ROM test.
Information
ECU Aftertreatment system ECU.
Effect Inducement derate, error code.

Service Procedure

Fault Description
Code
P006A-92 Performance or incorrect performance - engine ECU (internal control module monitoring processor
performance)
P060A-93 No operation - engine ECU (internal control module monitoring processor performance)
P060B

Information
Service Procedure

Internal control module A/D processing performance - functional safety fault
Processing fault within within the engine ECU
Information
ECU Engine ECU.
Effect Inducement derate, error code.

Service Procedure

P060C

Information
Service Procedure

Monitoring error on aftertreatment or engine ECU
Engine or aftertreatment ECU has detected an internal ECU fault.
Information
Effect Reduced Power Mode (Engine Derate) Engine Inducement, error code.

Service Procedure
1. Use the FTB code table below to establish which ECU has flagged the fault code.

P060C-00 No sub type information
P060C-F0 Unallocated (JCB Controlled) - engine ECU (Internal control module main processor performance)
P060C-41 General checksum failure - aftertreatment system ECU
P060C-44 Data memory failure - engine ECU
P060C-46 Calibration /Parameter main processor memory failure - engine ECU
P060C-68 Event information (aftertreatment system ECU software reset performed)
P060C-94 Unexpected operation (aftertreatment system ECU software reset performed)
P0612

Information
Service Procedure

Engine speed relay driver
Fault on the engine speed controller relay.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Check machine side relay and circuit for faulty components, refer to engine speed controller.

P0612-00 Short circuit
P0615

Information
Service Procedure

Starter relay circuit
Fault on the starter motor control relay.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page starter motor inhibit relay.

P0616

Information
Service Procedure

Starter relay circuit low
Information
ECU Engine ECU.
Effect
Service Procedure

P0617

Information
Service Procedure

Starter relay circuit high
Information
ECU Engine ECU.
Effect
Service Procedure

P062D

Information
Service Procedure

Fuel injector driver circuit performance
Fault on the fuel injector circuit.
Information
ECU Engine ECU.
Effect
Possible Cause Injector short circuit

Service Procedure

P062D-00 No sub type information
P062D-11 Short circuit to ground (SC2G)
P062D-12 Short circuit to battery (SC2VBAT)
P062D-19 Circuit current above threshold
P062E

Information
Service Procedure

Fuel injector driver circuit performance
Fault on the fuel injector circuit.
Information
ECU Engine ECU.
Effect Engine fails to start or stops if running.
Service Procedure

P062E-00 No sub type information
P062E-11 Short circuit to ground (SC2G)
P062E-12 Short circuit to battery (SC2VBAT)
P062F

Information
Service Procedure

Internal control module EPROM error
Memory fault detected on the engine electronic control unit (ECU).
Information
ECU Engine ECU.
Effect

Service Procedure

P062F-00 No sub type information
P0627

Information
Service Procedure

Lift pump global fault
Fault on the lift pump control circuit.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page fuel lift pump test.

P0628

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P0628-11 Short circuit to ground
P0629

Information
Service Procedure

Information
ECU Engine ECU.
Effect
Service Procedure

P0629-12 Short circuit to battery
P0630

Information
Service Procedure

VIN not programmed or incompatible - ECM/PCM
Variant coding not programmed, incompatible or corrupted – ECM.
Information
ECU Engine ECU.
Effect Engine features may not function correctly.
Possible Cause Variant coding not correctly configured.
Service Procedure
1. Check that the engine ECU software identification is correct for the machine type. Refer to re-flashing an
ECU.
2. If the software identification is not correct, carry out 'Restore Default'. Refer to re-flashing an ECU.
3. Re-flash the ECU. Make sure that the machine options and specifications are entered correctly.

P0641

Information
Service Procedure

Sensor reference voltage "A" circuit/open
Fault with the power connections.
Information
ECU Engine ECU.
Effect
Water or corrosion in connectors.
Service Procedure
connector terminals. This may be as a consequence of pressure washing the engine or machine, loose
connectors or poor connector sealing.
3. Complete the testing procedure described in the component page engine ECU sensor supply.

P0650

Information
Service Procedure

Malfunction Indicator Lamp (MIL) driver fault
Fault on the circuit controlling the malfunction indicator lamp (MIL).
Information
ECU Engine ECU.
Effect

Faulty MIL.
Service Procedure
1. Check operation of the lamp, refer to MIL test.

P0651

Information
Service Procedure

Sensor reference voltage "B" circuit/open
Fault with the power connections.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page engine ECU sensor supply.

P0655

Information
Service Procedure

Check Engine Lamp (CEL) fault
Fault on the circuit controlling the check engine lamp (CEL).
Information
ECU Engine ECU.
Effect

Faulty CEL.
Service Procedure
1. Check operation of the lamp, refer to CEL test.

P0656

Information
Service Procedure

Fuel level output circuit
Message fault from the fuel level switch.
Information
ECU Engine ECU.
Effect
Service Procedure
P0656 Message fault from the fuel level switch.
P0658

Information
Service Procedure

Actuator relay 1
Ground short circuit error has been detected for actuator relay 1 (heated DEF lines).
Information
Effect
Service Procedure
3. Complete the testing procedure described in the component page aftertreatment ECU and heated DEF lines.

P0659

Information
Service Procedure

Actuator relay 1
Battery short circuit error has been detected for actuator relay 1 (heated DEF lines).
Information
Effect
Service Procedure
3. Complete the testing procedure described in the component page aftertreatment ECU and heated DEF lines.

P0668

Information
Service Procedure

PCM/ECM/TCM internal temperature sensor "A" circuit low
Internal temperature sensor fault on the engine electronic control unit (ECU).
Information
ECU Engine ECU.
Effect

Faulty sensor.
Service Procedure

P0669

Information
Service Procedure

PCM/ECM/TCM internal temperature sensor "A" circuit high
Internal temperature sensor fault on the engine electronic control unit (ECU).
Information
ECU Engine ECU.
Effect

Faulty sensor.
Service Procedure

P0685

Information
Service Procedure

ECM/PCM power relay control circuit/open
Fault on the power hold relay for the engine electronic control unit (ECU).
This error code will be generated following a power hold relay test, or after adjusting the ECU calibration.
Information
ECU Engine ECU.
Effect

Power hold relay test carried out.
ECU calibration adjusted.
Service Procedure
3. Complete the testing procedure described in the component page engine ECU power hold relay.

P0685-72 Actuator stuck open
P0697

Information
Service Procedure

Sensor Reference Voltage "C" Circuit/Open
Sensor power supply fault.
Information
ECU Engine ECU.
Effect Limp home mode.

Faulty ECU.
Service Procedure
3. Complete the testing procedure described in the component page ECU power connections.

P0697-4B Over temperature
P06A7

Information
Service Procedure

Sensor supply monitoring error through DCU
Fault with sensor supply voltage within the aftertreatment system ECU.
Information
Effect

Faulty ECU.
Faulty sensor.
Service Procedure

P0715

Information
Service Procedure

Input/turbine speed sensor "A" circuit
ECU power fault on the variable geometry turbocharger (VGT).
Information
ECU Engine ECU.
Effect
Faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component page VGT.

P1101

Information
Service Procedure

Rail pressure control error positive fault
Problem controlling the fuel rail pressure.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page general high pressure fuel system fault
table.

P1102

Information
Service Procedure

Rail pressure control error negative fault
Problem controlling the fuel rail pressure.
Information
ECU Engine ECU.
Effect
Service Procedure
table.

P1103

Information
Service Procedure

Rail pressure fault
The fuel rail is not maintaining pressure after an engine shut down.
Information
ECU Engine ECU.
Effect

Fuel leak on the fuel rail.
Service Procedure
table.

P1104

Information
Service Procedure

Injector 3 Update Fault
No minimum drive pulse (MDP) updates occurred on Injector 3 due to environmental conditions.
Information
ECU Engine ECU.
Effect Reduced power mode (engine derate) - torque reduction.
Possible Cause Other fault codes present.
Service Procedure
1. Check for other fault codes and repair as required.
2. Clear the fault codes.

P1105

Information
Service Procedure

No minimum drive pulse (MDP) updates occurred on Injector 3 due to a fault within the update strategy.
Information
ECU Engine ECU.
Service Procedure

P1106

Information
Service Procedure

Information
ECU Engine ECU.
Service Procedure

P1107

Information
Service Procedure

Information
ECU Engine ECU.
Service Procedure

P1108

Information
Service Procedure

Information
ECU Engine ECU.
Service Procedure
P1109

Information
Service Procedure

Information
ECU Engine ECU.
Service Procedure

P110A

Information
Service Procedure

Information
ECU Engine ECU.
Service Procedure

P110A-00 No sub type information.
P110B
Information
Service Procedure

Information
ECU Engine ECU.
Service Procedure

P110B-00 No sub type information.
P1400

Information
Service Procedure

Override switch
Fault with the override switch.
Information
Effect Error code.

Faulty switch.
Service Procedure

P1401

Information
Service Procedure

Override switch
Frame length error of PROSCR16 containing override switch information from engine electronic control unit
(ECU).
Information
Effect Error code.

Faulty switch.
Service Procedure

P1402

Information
Service Procedure

Override switch
Frame timeout error has been detected by the override switch.
Information
Effect Error code.

Faulty switch.
Service Procedure

P1500

Information
Service Procedure

Foot throttle/pedal signal fault
Fault on the foot throttle position sensor signal. For safety, the engine has gone into limp home mode.
Information
ECU Engine ECU.
Effect Reduced power mode (engine derate) - limp home mode.

Faulty sensor.
Service Procedure

P1501

Information
Service Procedure

Foot throttle/pedal signal fault
Fault on the foot throttle position sensor signal. For safety, the engine has gone into reduced torque mode mode.
Information
ECU Engine ECU.
Effect Reduced power mode (engine derate) - reduced torque mode.

Faulty sensor.
Service Procedure

P1503

Information
Service Procedure

Hand throttle/pedal signal fault
Fault on the hand throttle position sensor signal. For safety, the engine has gone into limp home mode.
Information
ECU Engine ECU.

Faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component page hand throttle position sensor.
P1504

Information
Service Procedure

Hand throttle/pedal signal fault
Fault on the hand throttle position sensor signal. For safety, the engine has gone into reduced torque mode.
Information
ECU Engine ECU.

Faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component page hand throttle position sensor.

P1506

Information
Service Procedure

Throttle/pedal global fault - limp home mode
Fault on the throttle signal. For safety, the engine has gone into limp home mode,
Information
ECU Engine ECU.

Faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component pages foot throttle position sensor and hand
throttle position sensor.

P1509

Information
Service Procedure

CAN communication error on TSC
Error in the signal received from a CAN based throttle.
Information
ECU Engine ECU.
Effect

Faulty throttle sensor.
Service Procedure
3. Complete the testing procedure described in the component page Electrical Network (CANBUS) Fault Table.
4. If no faults are found refer to machine information for diagnosing faults with the throttle controller system.

P1602

Information
Service Procedure

Starter motor relay global driver
Error with the voltage driver used to control the starter motor inhibit relay.
Information
ECU Engine ECU.
Effect
Service Procedure

P2000

Information
Service Procedure

Conversion efficiency
An error has been detected with the actual average conversion efficiency (below the threshold efficiency).
Information
Effect Reduced Power Mode (Engine Derate), error code.
Possible Cause NOx sensors connected incorrectly.

Faulty sensor on the exhaust aftertreatment system.
Faulty exhaust aftertreatment catalyst.
Contaminated or incorrect fuel specification used
Service Procedure
1. Check for additional fault codes, repair as required.
2. Check that the upstream and downstream NOx sensors are connected correctly.
3. Check that the fuel is not contaminated and is to the correct specification. Refer to the operators manual.
4. Perform SCR Catalyst testing procedure.
5. Perform the exhaust aftertreatment catalyst refresh procedure. Refer to the machine operators manual.
6. If fault persists, raise a Techweb Helpdesk call.

P2000-00 No sub type information (actual average conversion efficiency is below the threshold)
P2000-02 General signal failure (actual average conversion efficiency is below the threshold)
P2000-04 System internal failure (actual average conversion efficiency is below the threshold)
P2000-06 Algorithm based failure (actual average conversion efficiency is below the threshold)
P202A

Information
Service Procedure

DEF tank heater actuator power stage
Open load error of the urea tank heater has been detected.
Information
Effect Error code.
Service Procedure
3. Complete the testing procedure described in the component page heated DEF lines.

P202A-13 Open load
P202B

Information
Service Procedure

Ground short circuit error of the DEF tank heater actuator.
Information
Effect Error code.
Service Procedure

P202B-14 Short circuit to ground or open circuit
P202C

Information
Service Procedure

Battery short circuit error of the DEF tank heater actuator.
Information
Effect Error code.
Service Procedure

P202C-13 Short circuit to battery or open circuit
P202E

Information
Service Procedure

Dosing valve
This fault code indicates an error has been detected with the DEF dosing valve.
Information

Faulty dosing control module.
Service Procedure
2. Make sure that the engine ECU and the aftertreatment ECU are flashed with the latest software.
4. Complete the testing procedure described in the component page dosing module.

P202E-00 No sub type information (Error on dosing valve short circuit)
P202E-02 General signal failure (Error on dosing valve plausibility)
P202E-4B Over temperature (Error on dosing valve driver over temperature)
P202E-12 Short circuit to battery (Error on dosing valve short circuit to battery)
P202E-13 Circuit open (Error on dosing valve short circuit to battery on high side or open load)
P202E-14 Short to ground or open circuit (Error on dosing valve short to ground or open circuit)
P202E-16 Dosing valve plausibility at low voltage (Error on dosing valve plausibility at low voltage)
P203B

Information
Service Procedure

Head unit
Multiple errors has been detected by the head unit.
Information
ECU Aftertreatment system ECU

Faulty head unit.
Service Procedure
3. Complete the testing procedure described in the component page head unit.

Fault Description
Code
P203B-00 No sub type information (Tank level signal error)
P203B-14 Circuit short to ground or open (DEF tank level signal is below minimum voltage limit)
P203B-15 Circuit short to battery or open (DEF tank level signal is above the maximum voltage limit)
P203B-16 Circuit voltage below threshold (Error on tank level plausibility)
P203B-22 Signal amplitude greater then maximum (Tank head unit level physical signal above maximum
limit)
P203B-81 Invalid serial data received (Can bus message error from head unit)
P203B-86 Signal invalid (Can bus message error for tank level from head unit)
P203B-87 Missing CAN message from engine ECU (CAN BUS off error from head unit)
P203F

Information
Service Procedure

DEF tank
Low/empty DEF tank level error has been detected.
Information
Possible Cause DEF tank level low or empty.

Faulty DEF level sensor (head unit).
Service Procedure
1. fill the DEF tank with DEF (to above 30%) and replace filler cap.
2. Switch on the ignition to check whether the fault has been fixed.
3. If fault remains, remove head unit and confirm DEF level with a dipstick.
4. Check that the sensor float on the head unit can move freely.

P203F-7B Low fluid level (DEF tank level low and empty)
P203F-21 Event information (Tank head unit level physical signal below minimum limit)
P203F-68 Signal amplitude less than minimum (DEF tank level low and below warning threshold)
P2043

Information
Service Procedure

Head unit
CAN communication error has been detected between the head unit and aftertreatment system ECU.
Information
Effect Error code.
Service Procedure

Invalid serial data received (CAN BUS message error from head unit)
P2043-81
Signal invalid (DEF temperature message error from head unit)
P2043-86
Missing CAN message from ECU (CAN BUS off error from head unit)
P2043-87
P204B

Information
Service Procedure

DEF pressure line
Error has been detected with the DEF pressure line while monitoring for blockage.
Information

Error code.
Possible Cause DEF system pressure related problem.

Blocked dosing module.
Internal sensor failure.
Damaged harness or harness connector
.Def tank overfilled.
Service Procedure
1. Check all of the DEF lines for kinks or bends.
2. If a P204B-02 code has been generated and the machine is used mainly for low duty cycles, the fault may be
able to be cleared by working the machine harder periodically. Make sure that the ECU software is up to
date. Refer to bulletins and the machine help files for full details.
3. Remove the DEF lines and check for any signs of blockages or contamination.
4. Inspect the supply module filters (main filter and pre-filter). Replace the filters as required.
5. Make sure that the DEF tank has not been overfilled.
6. Perform the DEF dosing quantity test test and confirm the system is able to purge correctly.
7. Remove the dosing module and clean any deposits from the tip. Refer to dosing module.
8. Complete the testing procedure described in the component page supply module.
9. If inducement is active and the machine is in forced idle, make sure the problem has been rectified. Start the
engine and operate the machine to load the engine and increase the exhaust temperature, the temperature
needs to exceed 150°C. This will allow the SCR system to prime and run through the diagnostic process,
once complete and all diagnostics have passed the fault will clear. This process can take up to 5 minutes. In
order to regain full power, follow the fault clearance procedure in reduced power mode (engine derate).

P204B-00 No subtype information (Error while monitoring the stabilisation of pressure)
P204B-02 General signal failure (Error on pressure line & dosing valve while monitoring for blockage)
P204B-16 Circuit voltage below threshold (Measured value of pressure sensor below the tolerable limit)
P204B-17 Circuit voltage above threshold (Measured value of pressure sensor above the tolerable limit)
P204B-26 Signal rate of change below threshold (Error on rate of pressure reduction )
P204B-29 Signal Invalid (Error on pressure line while monitoring for blockage)
P204B-61 Signal calculation failure (Error while monitoring of pressure buildup)
P204C

Information
Service Procedure

Pump pressure signal
This fault code indicates an error with the pump pressure signal.
Information
Service Procedure

P204C-16 Circuit voltage below threshold (pump pressure signal below the minimum voltage limit)
P204C-21 Signal amplitude less than minimum (error for pump pressure physical signal below lower limit)
P204D

Information
Service Procedure

Pump pressure signal range
This fault code indicates an error with the pump pressure signal range (above the maximum limit).
Information
Service Procedure

P204D-17 Circuit voltage above threshold (pump pressure signal above the maximum voltage limit)
P204F

Information
Service Procedure

Blocked filter
Clogged filter in the supply module or DEF leak on the dosing system
OR
Repeat offence
An emission related fault code has become active within 40 engine running hours from being cleared
Information
ECU Engine/Aftertreatment system ECU.
Possible Cause Repeat offence (P204F-9A).

Blocked DEF filter.
Aftertreatment system DEF leak.
Service Procedure
P204F-06, P204F-7A
1. Check the DEF hoses for signs of damage and any leaks.
2. Replace the DEF filter.
P204F-9A
2. Perform system reset following 'Repeat Offence.' Refer to Reduced Power Mode (Engine Derate).

Fault Description
Code
P204F-06 Algorithm based failure - Aftertreatment DCU (Error to detect the clogged filter)
P204F-7A Fluid leak or seal failure - Aftertreatment DCU (Error to detect leakage during no dose)
P204F-9A Repeat offence active (an emission related fault code has become active within 40 engine running
hours)
P205B

Information
Service Procedure

DEF tank header unit
Tank heater plausibility or response error detected.
Information

Damaged, blocked or faulty coolant valve.
Failure of head unit.
Service Procedure
1. Check that the coolant valve is operating correctly and is not blocked, Refer to coolant valve.
2. Check that the coolant pipes to and from the DEF tank are routed correctly.
3. Check the DEF tank temperature value in SM, this should be close to ambient if the head unit is removed
and still electrically connected.
4. Check for any damaged or loose pins and debris or water inside the connector terminals of the
aftertreatment ECU, DEF tank header unit and DEF coolant valve. This may be as a consequence of
pressure washing the engine, loose connectors or poor connector sealing.

Fault Description
Code
P205B-00 No subtype information (Error to indicate overheating of DEF tank due to coolant valve stuck open)
P205B-06 Algorithm based failure (Error in increase of DEF tank temperature to suggest coolant valve stuck
shut)
P205B-16 Circuit voltage above threshold (Tank head unit temperature physical signal below minimum limit)
P205B-17 Circuit voltage above threshold (Tank head unit temperature physical signal above maximum limit)
P205B-23 Signal stuck low (Error on tank temperature sensor plausibility below minimum threshold)
P205B-24 Signal stuck high (Error on tank temperature sensor plausibility exceeds maximum threshold)
P205C

Information
Service Procedure

Tank temperature signal voltage
Error with the temperature signal voltage, it is below the minimum limit.
Information
Effect Error code.

Faulty head unit.
Service Procedure

P205C-16 Circuit voltage below minimum limit
Algorithm based failure (Error in increase of DEF tank temperature)

P205D

Information
Service Procedure

Tank temperature signal voltage
Error with the temperature signal voltage, it is above the maximum limit.
Information
Effect Error code.

Faulty head unit.
Service Procedure

P205D-17 Circuit voltage above maximum limit
Algorithm based failure (Error in increase of DEF tank temperature)

P205E

Information
Service Procedure

Tank temperature from head unit
Erroneous signal for aftertreatment 1 diesel exhaust fluid tank temperature.
Information
Effect Error code.
Service Procedure

P205E-81 Tank temperature signal error (tank temperature signal error on CAN)
P205E-87 Missing CAN message from ECU (CAN BUS message error for tank temperature from head unit)
P207F

Information
Service Procedure

DEF quality from head unit
Error for aftertreatment system diesel exhaust fluid property (quality) from tank head unit.
Information
Possible Cause Poor quality DEF.

Contaminated DEF tank.
Faulty quality sensor (head unit).

Service Procedure
The quality sensor is active for 1 minute after the ignition is switched on and the DEF tank temperature is
above -2°C. Any contamination picked up during machine use will not be detected. The ignition
should always be switched off and the machine made safe before refilling the DEF tank.
1. Take a sample of DEF and confirm quality is with in spec. Refer to DEF quality test.
2. If DEF is not within spec the system must be drained and the complete aftertreatment system must be
cleaned.

P207F-00 No sub type information (DEF quality error during refill condition)
P207F-86 Signal Invalid (DEF concentration message error from head unit)
P207F-87 Missing CAN message (DEF quality message error from head unit)
P2080

Information
Service Procedure

Exhaust gas temperature sensor circuit range/performance
Fault with the Variable Geometry Turbocharger (VGT) system.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page VGT.

P208A

Information
Service Procedure

Open load error of supply module pump motor
Open load error on the PWM output power stage for the actuator of the supply module pump motor
Information

Faulty supply module.
Service Procedure

P208A-13 Circuit open (Open load error of supply module pump motor)
P208A31 No Signal (supply module pump feedback error)
P208B

Information
Service Procedure

Error on supply module pump motor
Error on the PWM output powerstage for the actuator- Supply Module
Information

Service Procedure

P208B-02 General signal failure (error on supply module pump speed permanent deviation)
P208B-4B Over temperature (over temperature error of supply module pump motor)
P208B-21 Signal amplitude less than minimum (supply module internal duty cycle below min range)
P208B-22 Signal amplitude greater than maximum (supply module internal duty cycle in invalid range)
P208B-61 Signal calculation failure (error on supply module pump speed deviation)
P208B-84 Signal below allowable range (supply module motor speed duty cycle below minimum range)
P208B-85 Signal above allowable range (supply module motor speed duty cycle above maximum range)
P208C

Information
Service Procedure

Supply module pump motor
Short circuit to ground error of the supply module pump motor.
Information

Service Procedure

P208C-14 Short circuit to ground
P208D

Information
Service Procedure

Supply module pump motor
Short circuit to battery error of the supply module pump motor.
Information

Service Procedure

P208D-13 Short circuit to Battery
P209F

Information
Service Procedure

DEF tank heater
Error for over-temperature of the DEF tank heater power stage.
Information
Effect Error code.
Possible Cause Faulty coolant valve

Faulty DEF tank temperature sensor (head unit)
Service Procedure
3. Complete the testing procedure described in the component page coolant valve.

P209F-4B Over temperature
P20A0

Information
Service Procedure

Back-flow pump
Open load error of the PWM output power stage of the DEF back-flow pump.
Information
Service Procedure

P02A0-13 Open Load (Back flow pump actuator power stage)
P20A1

Information
Service Procedure

Back flow pump actuator power stage
Over temperature error at PWM output power stage of the DEF back flow pump.
Information
Possible Cause Faulty DEF pump (supply module).

Service Procedure

P20A1-4B Over temperature
P20A2

Information
Service Procedure

Short circuit to ground error at PWM output power stage of the DEF back flow pump.
Information

Service Procedure

P20A2-14 Short circuit to ground
P20A3

Information
Service Procedure

Short circuit to battery error at PWM output power stage of the DEF back flow pump.
Information

Service Procedure

P20A3-13 Short circuit to battery
P20AD
Engine > Fault Codes > P20AD

Information
Service Procedure

Supply module temperature
Fault with the DEF supply module temperature sensor (dynamic plausibility.
Information
Possible Cause Faulty supply module.

Service Procedure

Fault Description
Code
P20AD-06 Algorithm based failure (error on supply module temperature)
P20AD-21 Signal amplitude less than minimum (supply module temperature duty cycle below minimum range)
P20AD-22 Signal amplifier greater than maximum (supply module temperature duty cycle above maximum
range)
P20AD-92 Performance or incorrect operation (error on supply module temperature cold start)
P20B5

Information
Service Procedure

Supply module heater actuator power stage
Open load error of the DEF supply module heater.
Information
Effect Error code.
Service Procedure

P20B5-13 Open load
P20B6

Information
Service Procedure

Supply module heater
Error of the DEF supply module heater actuator power stage.
Information
Possible Cause Faulty supply module.

Service Procedure

Fault Description
Code
P20B6-4B Over temperature (Error for over temperature of supply module heater actuator power stage)
P20B6-21 Signal amplitude less than minimum (Supply module heater temperature duty cycle below minimum
range)
P20B6-22 Signal amplitude greater than maximum (Supply module heater temperature duty cycle above
maximum range)
P20B7

Information
Service Procedure

Short to ground of supply module heater actuator power stage
Short circuit to ground error of the DEF supply module.
Information
Effect Error code.
Service Procedure

P20B7-14 Short circuit to ground
P20B8

Information
Service Procedure

Supply module heater actuator power stage
Error for the short circuit to battery of the DEF supply module heater.
Information
Effect Error code.
Service Procedure

P20B8-13 Short circuit to battery
P20B9

Information
Service Procedure

Back flow line
Open load error on DEF heater relay back flow line.
Information
Effect Error code.
Service Procedure

P20B9-00 No sub type information (Error for open load on heater relay of back flow line)
P20B9-13 Short circuit to battery (Open load error of DEF back flow line heater actuator power stage)
P20BA
Engine > Fault Codes > P20BA

Information
Service Procedure

DEF back flow line heater actuator power stage
Over temperature error of the DEF back flow line heater actuator power stage.
Information
Effect Error code.
Service Procedure

P20BA-4B Over temperature
P20BB
Engine > Fault Codes > P20BB

Information
Service Procedure

Backflow Line Heater control / circuit fault
Short circuit to ground or open load error of the DEF heater relay circuit 4 (Backflow Line).
Information
Effect Error code.

Reduced Power Mode (Engine Derate).
Dosing interrupted if defrost/heating is required.
Possible Cause Fuse blown.
Backflow line heater not connected properly.

Faulty hose heaters main relay.
Faulty backflow heated line relay.
Faulty backflow heated Line.
Service Procedure
1. Complete the testing procedure described in the component page DEF Hose Heaters Main Relay Test. If
test fails, carry out the following checks:
1. Check the fuses.
2. Check the backflow line heater is connected properly.
3. Check the hose heaters main relay.
4. Check the backflow heated Line relay.
5. Check the continuity of the backflow line heater.

P20BB-00 No sub type information (error for short to ground or open load on heater relay of back flow line)
P20BB-14 Short to ground (error for short to ground of DEF back flow line heater actuator power stage)
P20BC
Engine > Fault Codes > P20BC

Information
Service Procedure
Short to battery of DEF back flow line heater actuator power stage
Error for short circuit to battery of the DEF back flow line heater actuator power stage.
Information
Effect Error code.
Service Procedure

P20BC-15 Short circuit to battery
P20BD
Engine > Fault Codes > P20BD

Information
Service Procedure

Heater relay 3 of pressure line
Open load error with the heater relay of the pressure line.
Information
Effect Error code.
Service Procedure

P20BD-00 No sub type information
P20BD-13 Open load
P20BE
Engine > Fault Codes > P20BE

Information
Service Procedure

Supply module heater
Error with the supply module heater plausibility or reduced DEF heating capability.
Information

Line heater relays or power relay fault.
Internal supply module continuity fault.
Service Procedure
1. Check for additional fault codes. Repair as required.
2. Check for any damaged or loose pins and debris or water inside the supply module and aftertreatment ECU

P20BE-00 No sub type information (Error on supply module heater )
P20BE-02 General signal failure (Error on supply module heater temperature sensor)
P20BE-4B Over temperature (Error for over temperature of DEF pressure line heater actuator power stage)
P20BE-05 System programing failure (Error on supply module heater temperature cold start)
P20BE-13 Circuit Open (Error on relays for short to battery)
P20BE-93 No operation (Error on pressure line to perform after run )
P20BF
Engine > Fault Codes > P20BF

Information
Service Procedure

Pressure Line Heater control / circuit fault
Short circuit to ground or open load error of the DEF heater relay circuit 3 (Pressure Line).
Information

Error code.
Dosing interrupted if defrost/heating is requested.

Pressure line heater not connected properly.
Faulty pressure heated line relay.
Faulty pressure heated line.
Service Procedure
2. Check the fuses.
3. Check the pressure line heater is connected properly.
5. Check the pressure heated line relay.
6. Check the continuity of the pressure line heater.

P20BF-00 No sub type information
P20BF-14 Short to ground
P20C0
Engine > Fault Codes > P20C0

Information
Service Procedure

DEF pressure line heater actuator power stage
Short circuit error to battery of the DEF pressure line heater power stage.
Information
Effect Error code.
Service Procedure

P20C0-15 Short circuit to battery
P20C1

Information
Service Procedure
Heater relay of suction line

Open load to ground error of the DEF heater relay 5 (suction line).
Information
Effect Error code.
Service Procedure

P20C1-00 No sub type information
P20C1-13 Open load error of DEF suction line heater actuator power stage
P20C2

Information
Service Procedure

DEF suction line heater actuator power stage
Over temperature error of the DEF suction line heater actuator power stage.
Information
Effect Error code.
Service Procedure

P20C2-4B Over temperature
P20C3

Information
Service Procedure

Suction Line Heater control / circuit fault
Short circuit to ground or open load error of the DEF heater relay circuit 5 (suction line).
Information

Error code.
Dosing interrupted if defrost/heating is requested.

Suction line heater not connected properly.
Faulty suction heated line relay.
Faulty suction heated line.
Service Procedure
2. Check the fuses.
3. Check the suction line heater is connected properly.
5. Check the suction heated line relay.
6. Check the continuity of the suction line heater.

P20C3-00 No sub type information (error for short to ground or open load on heater relay of suction line)
P20C3-14 Short circuit to ground (error for short to ground of DEF suction line heater actuator power stage)
P20C4

Information
Service Procedure

DEF suction line heater actuator power stage
Short circuit to battery error of the DEF suction line heater actuator power stage.
Information
Effect Error code.
Service Procedure

P20C4-15 Short circuit to battery
P20E8
Engine > Fault Codes > P20E8

Information
Service Procedure

Under pressure error in metering control state
Under pressure error has been detected in the metering control state.
Information
Possible Cause Blockage in DEF line.

DEF tank Empty.
Service Procedure
1. Check DEF level.
2. If there is DEF present, check DEF lines for damage or kinks.
3. Check DEF backflow line for blockages.

P20E8-84 Under pressure
P20E9
Engine > Fault Codes > P20E9

Information
Service Procedure

Supply module/metering state
Overpressure error regardless of the state.
Information
Possible Cause Blockage in DEF line.

Service Procedure
1. Check DEF lines for damage or kinks.
2. Check DEF backflow line for blockages.

P20E9-00 No sub type information
P20E9-85 Overpressure in metering control state
P20EA
Engine > Fault Codes > P20EA

Information
Service Procedure

DCU relay early opening
Error with the power hold relay of the aftertreatment system ECU early opening.
Information
Effect Error code.

Faulty power hold relay.
Service Procedure
3. Complete the testing procedure described in the component page Aftertreatment system ECU.

P20EA-72 Early opening
P20EB
Engine > Fault Codes > P20EB

Information
Service Procedure

Aftertreatment system ECU relay stuck
Power hold relay of the aftertreatment system ECU is stuck.
Information
Effect Error code.
Faulty power hold relay.
Service Procedure

P20EB-71 Actuator stuck
P2100

Information
Service Procedure

Throttle H-Bridge wiring fault
An intermittent or permanent break in the circuit powering the throttle motor has been detected.
Information
ECU Engine ECU.

Error code.
Possible Cause Throttle harness connector removed.

Electrical fault with the intake throttle.
Service Procedure
3. With both the engine ECU and the intake throttle electrical connectors removed, check the electrical
continuity between the following:
a. Throttle connector pin 1 and ECU connector pin 57.
b. Throttle connector pin 2 and ECU connector pin 60.
Refer to Intake Throttle for schematics and pin identification.
4. If no wiring faults exist and the fault remains, replace the intake throttle.

P2100-02 Throttle short circuit
P2100-13 Permanent or intermittent open circuit.
P2101

Information
Service Procedure

Permanent or intermittent short circuit.
Information
ECU Engine ECU.
Effect Reduced Power Mode (Engine Derate), error code
Service Procedure
Important: Use the multi-meter on the harness connector pins. DO NOT use the meter on the ECU pins. (SN0011)
3. Disconnect both the engine ECU connector and the Intake throttle connector.
4. Check for short circuits between pins 57 and 60 and the engine ECU connector and pins 1 and 2 at the inlet
throttle connector.
5. Check for short circuits or low resistance to earth.
6. Check for short circuits or low resistance to battery positive.
7. Check for short circuits or low resistance to pins 2, 3 and 5 within the throttle connector.
8. Replace throttle.

P2101-02 Permanent or intermittent short circuit.
P2102

Information
Service Procedure

A short circuit to ground in the circuit powering the throttle motor has been detected.
Information
ECU Engine ECU.

Service Procedure
4. If the fault remains replace the intake throttle.

P2103

Information
Service Procedure

A short circuit to the battery in the circuit powering the throttle motor has been detected.
Information
ECU Engine ECU.

Service Procedure
4. If the fault remains replace the intake throttle.

P2120

Information
Service Procedure

Hand pedal signal track 1 fault
Fault on the signal from track 1 of the hand throttle position sensor.
Information
ECU Engine ECU
Effect
Service Procedure
3. Complete the testing procedure described in the component page Hand throttle position sensor.

P2125

Information
Service Procedure

Hand pedal signal track 2 fault
Fault on the signal from track 2 of the hand throttle position sensor.
Information
ECU Engine ECU
Effect
Service Procedure

P2135

Information
Service Procedure

Throttle/pedal position sensor/switch "A"/"B" voltage correlation
Fault on the throttle pedal position sensor.
Information
ECU Engine ECU
Effect
Service Procedure


P2138

Information
Service Procedure

Hand pedal signal correlation fault
Fault with the correlation between the two position signals from the hand throttle position sensor.
Information
ECU Engine ECU
Effect
Service Procedure

P2147

Information
Service Procedure

Injector supply voltage fault
Fault with voltage supply for the fuel injector.
Information
ECU Engine ECU.
Effect
Service Procedure

P2148

Information
Service Procedure

Injector supply voltage fault
Fault with voltage supply for the fuel injector.
Information
ECU Engine ECU.
Effect
Service Procedure

P219D

Information
Service Procedure

DEF heater relay actuator power stage
Error has been detected with the DEF heater relay.
Information
Effect Error code.
Service Procedure

P219D-4B Over temperature (error for over temperature of DEF heater relay actuator power stage)
P219D-13 Open load (Open load error of DEF heater relay actuator power stage)
P219E

Information
Service Procedure

Short circuit to battery error of the DEF heater relay power stage.
Information
Effect Error code.
Service Procedure

P219E-13 Short to battery
P219F

Information
Service Procedure

Short circuit to ground error of the DEF heater relay power stage.
Information
Effect Error code.
Service Procedure

P219F-14 Short to ground
P21A9

Information
Service Procedure

Short circuit to battery of actuator relay 4
Short circuit error to battery error has been detected of actuator relay 4.
Information
Effect Error code.
Possible Cause Electrical fault.
Service Procedure

P21A9-12 Short to battery
P21AB
Engine > Fault Codes > P21AB

Information
Service Procedure

Short circuit to ground of actuator relay 4
Short circuit error to ground error has been detected of actuator relay 4.
Information
Effect Error code.
Possible Cause Electrical fault.
Service Procedure

P21AB-14 Short to ground
P2200

Information
Service Procedure

Upstream NOx sensor
A wiring fault has affected the upstream NOx sensor.
Information

Error code.
Possible Cause 12 Volt NOx sensor fitted to a 24 Volt machine.

24 Volt NOx sensor fitted to a 12 Volt machine.
Faulty sensor.
Open circuit and short circuit fault codes relate to wiring faults detected between the NOx sensor exhaust probe
and the Sensor Control Unit (SCU). The SCU is the unit that the machine wiring harness plugs into. As the
exhaust probe and SCU is a single item, an open or short circuit fault is likely to require sensor replacement.
Voltage fault codes relate to an error detected in the power supplied to the NOx sensor unit and suggest a
problem within the machine harness or power supply. As 12 and 24 volt sensors exist, check that the sensor
voltage shown on the SCU matches the machine voltage.
The AdBlue tank and both NOx sensors use the same power source and relay.
Service Procedure
3. Complete the testing procedure described in the component page upstream NOx sensor.

P2200-00 No sub type information (upstream NOx sensor wire diagnosis-error in voltage supply)
P2200-02 General signal failure (upstream NOx sensor short circuit to ground or battery)
P2200-05 System programming failure (upstream NOx sensor self diagnostic )
P2200-11 Circuit short to ground (lambda signal below minimum for upstream NOx sensor)
P2200-12 Circuit short to battery (lambda signal above maximum limit for upstream NOx sensor)x
P2200-13 Open circuit (upstream NOx sensor open circuit)
P2200-61 Signal calculation failure (invalid signal from upstream NOx sensor after heater release)
P2200-63 Circuit/component protection time-out (upstream NOx sensor self diagnostic timeout)
P2200-94 Unexplained operation (upstream NOx sensor self diagnostic abort)
P2201

Information
Service Procedure

Downstream NOx sensor
A wiring fault has affected the downstream NOx sensor.
Information
Possible Cause 12 Volt NOx sensor fitted to a 24 Volt machine.

24 Volt NOx sensor fitted to a 12 Volt machine.
Faulty sensor.
Open circuit and short circuit fault codes relate to wiring faults detected between the NOx sensor exhaust probe
and the Sensor Control Unit (SCU). The SCU is the unit that the machine wiring harness plugs into. As the
exhaust probe and SCU is a single item, an open or short circuit fault is likely to require sensor replacement.
Voltage fault codes relate to an error detected in the power supplied to the NOx sensor unit and suggest a
problem within the machine harness or power supply. As 12 and 24 volt sensors exist, check that the sensor
voltage shown on the SCU matches the machine voltage.
The AdBlue tank and both NOx sensors use the same power source and relay.
Service Procedure
3. Complete the testing procedure described in the component page downstream NOx sensor.

P2201-00 No sub type information. (Downstream NOx sensor wire diagnosis-error in voltage supply)
P2201-1C Circuit voltage out of range (Downstream NOx sensor short circuit to ground or battery)
P2201-06 Algorithm based failure (Downstream NOx sensor self diagnostic )
P2201-11 Circuit short to ground (Lambda signal below minimum limit for downstream NOx sensor)
P2201-12 Circuit short to battery (Lambda signal above maximum limit for downstream NOx sensor)
P2201-13 Open circuit (Downstream NOx sensor open circuit)
P2201-16 Circuit voltage below threshold (Downstream NOx offset min error detection)
P2201-17 Circuit voltage above threshold (Downstream NOx offset max error detection)
P2201-61 Signal calculation failure (Invalid signal from downstream NOx sensor after heater release)
P2201-63 Circuit/Component protection time-out (Downstream NOx sensor self diagnostic timeout)
P2201-97 Circuit/Component protection time-out (Downstream NOx sensor self diagnostic timeout)
P2202

Information
Service Procedure

NOx sensor reading below minimum threshold
An error has been detected with the NOx sensor reading.
Information

Service Procedure
3. Complete the testing procedure described in the component pages upstream NOx sensor and downstream
NOx sensor.

P2202-00 No sub type information (Upstream NOx sensor reading below minimum threshold)
P2202-16 Circuit voltage below threshold (Downstream NOx sensor reading below minimum threshold)
P2203

Information
Service Procedure

NOx sensor reading above maximum threshold
An error has been detected with the NOx sensor reading.
Information

Service Procedure
3. Complete the testing procedure described in the component pages upstream NOx sensor and downstream
NOx sensor.

Fault Description
Code
P2203-00 No sub type information.(Upstream NOx sensor reading exceeds above maximum threshold)
P2203-17 Circuit Voltage above threshold (Downstream NOx sensor reading exceeds above maximum
threshold)
P2208

Information
Service Procedure

An error has been detected with the downstream NOx sensor heater.
Information

Error code.
Possible Cause Sensor power supply fault.

Faulty sensor.
Heater fault codes can be caused by a faulty NOx sensor power supply. Always resolve any voltage error fault
codes before rechecking and resolving heater fault codes.
The DEF tank and both NOx sensors use the same power source and relay.
Service Procedure

P2208-00 No sub type information (downstream NOx sensor heater not available)
P2208-02 General signal failure (downstream NOx sensor heater not heated quickly)
P2209

Information
Service Procedure

Upstream NOx sensor
An error has been detected with the upstream NOx sensor heater.
Information

Error code.
Possible Cause Sensor power supply fault.

Faulty sensor.
Heater fault codes can be caused by a faulty NOx sensor power supply. Always resolve any voltage error fault
codes before rechecking and resolving heater fault codes.
The DEF tank and both NOx sensors use the same power source and relay.
Service Procedure
P2209-00 No sub type information (upstream NOx sensor heater not available)
P2209-02 General signal failure (upstream NOx sensor heater not heated quickly)
P2226

Information
Service Procedure

Barometric pressure sensor "A" circuit
Fault with the barometric/pressure sensor inside the ECU.
Information
ECU Engine ECU.
Effect

Faulty sensor.
Service Procedure
3. The ECU temperature sensor cannot be tested. If fault persists, raise a Techweb Helpdesk call.

P2228

Information
Service Procedure

Barometric pressure sensor "A" circuit low
Information
ECU Engine ECU.
Effect

Faulty sensor.
Service Procedure

P2229

Information
Service Procedure

Barometric pressure sensor "A" circuit high
Information
ECU Engine ECU.
Effect

Faulty sensor.
Service Procedure

P2264

Information
Service Procedure

Water in fuel sensor circuit
Fault on the water in fuel sensor.
Information
ECU Engine ECU.
Effect

Faulty sensor.
Service Procedure
3. Complete the testing procedure described in the component page water in fuel sensor.

P2265

Information
Service Procedure

Water in fuel sensor circuit range/performance
Fault on the water in fuel sensor circuit.
Information
ECU Engine ECU.
Effect
Service Procedure

P2265-2F Signal erratic.
P2266

Information
Service Procedure

Water in fuel sensor circuit low
Information
ECU Engine ECU.
Effect
Service Procedure

P2267

Information
Service Procedure

Water in fuel sensor circuit high
Information
ECU Engine ECU.
Effect
Service Procedure

P2269

Information
Service Procedure

Water in fuel condition
Information
ECU Engine ECU.
Possible Cause Water in fuel.

Faulty sensor.
Fuel hoses connected incorrectly.
Water in fuel sensor not disconnected.
Service Procedure
1. Check for water in the fuel sedimenter, drain as required.
4. Make sure that the connector for water in fuel sensor is connected correctly.

P2269-22 Gross water contamination
P2413

Information
Service Procedure

Impeded EGR fault data engine ECU
Error with the exhaust gas recirculation valve.
Information
ECU Engine ECU.

Error code.
Possible Cause Engine related fault affecting EGR flow (Intake throttle, EGR, VGT, Coolant
temp, blocked SCR)
CAN communication fault.
Service Procedure
1. Check for additional fault codes, correct as required.
2. Make sure the software is up to date and ECU is operating correctly.

Fault Description
Code
P2413-81 Invalid serial data received (CAN BUS message error for EGR faults from engine ECU)
P2413-86 Signal invalid (CAN BUS message error from engine ECU)
P2413-87 Missing CAN message from ECU (impeded EGR fault data or bus off for EGR faults from engine
ECU)
P2428

Information
Service Procedure

Exhaust Catalyst Temperature
Error with the exhaust catalyst temperature t4 physical signal, it is above the maximum
Information
Effect Error code.
Possible Cause Faulty Sensor

Service Procedure
3. Complete the testing procedure described in the component page pre SCR exhaust temperature sensor.

P242B

Information
Service Procedure

Upstream temperature sensor
An error has been detected with the upstream temperature sensor static plausibility.
Information
Service Procedure
3. Complete the testing procedure described in the component page exhaust temperature sensor.

Fault Description
Code
P242B-00 No sub type information. (error on SCR catalyst upstream temperature sensor static plausibility)
P242B-16 Circuit voltage below threshold (error on catalyst temperature sensor plausibility below min
threshold)
P242B-17 Circuit voltage above threshold (error on catalyst temperature sensor plausibility above max
threshold)
P242B-23 Signal stuck low (exhaust catalyst temperature t4 physical signal below minimum limit)
P242C

Information
Service Procedure

Upstream temperature sensor T4 voltage signal
An error has been detected with exhaust catalyst temperature t4 voltage signal, it is below the minimum limit
Information
Service Procedure

P242C-16 Circuit voltage below threshold
P242D

Information
Service Procedure

Exhaust catalyst temperature T4 voltage signal
An error has been detected with the exhaust catalyst temperature t4 voltage signal, it is above the maximum limit.
Information
Service Procedure

P242D-17 Circuit voltage above threshold
P2502

Information
Service Procedure

Power management from engine ECU
Error with power management.
Information
ECU Engine ECU.
Effect Error code.
Service Procedure


P2502-87 Missing CAN message from engine ECU
P250B

Information
Service Procedure

Engine oil level sensor circuit range/performance
Fault on the oil level switch circuit.
Information
ECU Engine ECU.
Effect
Service Procedure
3. Complete the testing procedure described in the component page oil level switch.

P250B-2F Signal erratic
P250F

Information
Service Procedure

Engine oil level too low
Low engine oil level.
Information
ECU Cluster
Effect
Possible Cause Low engine oil level.

Faulty sensor.
Service Procedure
1. Check the engine oil level, top up as required.

P250F-00 Signal Amplitude Less Than Minimum
P250F-86 Signal Invalid
P250F-87 Missing Message
P256A

Information
Service Procedure

Engine idle speed selector sensor/switch circuit/open
Fault on the engine speed controller.
Information
ECU Engine ECU.
Effect

Faulty engine speed controller.
Service Procedure
connector terminals. This may be as a consequence of pressure washing the engine, loose connectors or poor
connector sealing.
3. Complete the testing procedure described in the component page engine speed controller.

P256B

Information
Service Procedure

Engine idle speed selector sensor/switch range/performance
Information
ECU Engine ECU.
Effect

Service Procedure
connector sealing.

P256C

Information
Service Procedure

Engine idle speed selector sensor/switch circuit low
Information
ECU Engine ECU.
Effect

Service Procedure
connector sealing.

P256C-00 No sub type information
P256D

Information
Service Procedure

Engine idle speed selector sensor/switch circuit high
Information
ECU Engine ECU.
Effect

Service Procedure
connector sealing.

P256D-00 No sub type information
P2620

Information
Service Procedure

Throttle position feedback fault
An intermittent or permanent fault has been detected within the throttle blade monitoring.
Information
ECU Engine ECU.
Effect
Possible Cause Throttle harness connector removed.

Faulty inlet throttle.
Service Procedure
3. Disconnect the inlet throttle harness connector.
4. With the ignition switched off, check for continuity between pin 4 at the inlet throttle connector and machine
earth.
5. With the ignition switched on, check for 5 volts at pin 5 of the harness connector relative to machine earth.
6. With the ignition switched on, check for 5 volts at pin 5 relative to pin 4 (ECU earth) at the inlet throttle
harness connector.
7. With the ignition switched on, check for 0 volts at pin 3 of the harness connector relative to machine earth.
8. With the ignition switched on, check for 0 volts at pin 3 of the harness connector relative to pin 4 (ECU
earth).
9. If a fault is detected in the pin 3 to 5 tests above, disconnect the black ECU connector and:
10. Check for continuity between: Throttle connector pin 3 and ECU connector pin 23.
Refer to intake throttle for pin identification.
13. If no wiring faults exist and the fault remains, replace the intake throttle.

P2620-00 Throttle position feedback fault
P2670

Information
Service Procedure

A short circuit fault has been detected with the actuator relay 2.
Information
Service Procedure
connector sealing.

P2670-14 Short circuit to ground or open circuit
P2671

Information
Service Procedure

Information
Service Procedure
connector sealing.

P2685

Information
Service Procedure

Information
Service Procedure
connector sealing.

P2685-14 Short circuit to ground or open circuit
P2686

Information
Service Procedure

Information
Service Procedure
connector sealing.

P2A00

Information
Service Procedure

Upstream NOx sensor
A fault with the upstream NOx sensor has been detected , it is not mounted.
Information
Possible Cause Sensor unplugged.

Service Procedure
connector sealing.

P2A01

Information
Service Procedure

A fault with the downstream NOx sensor has been detected , it is not mounted.
Information
Possible Cause Sensor unplugged.

Service Procedure
connector sealing.

P2BA7
Engine > Fault Codes > P2BA7

Information
Service Procedure

DEF tank level
An error has been detected with the DEF level.
Information

Warning light.
Possible Cause Low fluid level or empty DEF tank.

Faulty level sensor (head unit).
Service Procedure
1. Check DEF level, top up as required.
2. Test DEF tank level sender unit by filling the DEF tank to confirm maximum gauge reading. Check the DEF
tank level using Servicemaster diagnostic tool and compare to the dash level indicator on the machine.

P2BA7-7B DEF level warning requested
P2BA7-F0 DEF level, level 2 requested - Forced idle (no throttle response) requested
P2BA7-68 DEF level, level 2 enacted - Forced idle (no throttle response) enacted
P2BA7-92 DEF level, level 1 enacted (25% torque derate enacted)
P2BA7-94 DEF level, level 1 requested (25% torque derate requested)
P2BA8

Information
Service Procedure

DEF dosing
An error has been detected with the dosing of the DEF.
Information

Warning light.
Possible Cause Fault preventing DEF injection.

Empty DEF tank.
Faulty dosing module.
Service Procedure
2. Complete the testing procedure described in the Dosing Module help page.

P2BA8-00 Interruption warning requested
P2BA8-F0 Interruption level 2 requested - Forced Idle (no throttle response) requested
P2BA8-68 Interruption level 2 enacted - Forced Idle (no throttle response) enacted
P2BA8-92 Interruption level 1 enacted (25% torque derate enacted)
P2BA8-94 Interruption level 1 requested (25% torque derate requested)
P2BA9

Information
Service Procedure

DEF quality
An error has been detected with the quality of the DEF.
Information

Warning light.
Possible Cause Contaminated or poor quality DEF.

Faulty quality sensor.
Frozen DEF.
Service Procedure
The quality sensor is active for 1 minute after the ignition is switched on and the DEF tank temperature is
above -2°C. Any contamination picked up during machine use will not be detected. The ignition
should always be switched off and the machine made safe before refilling the DEF tank.
1. Perform DEF quality testing.
4. Make sure the software is up to date and the ECU is operating correctly.
5. Check for additional fault codes, repair as required.

P2BA9-00 Quality Warning Requested
P2BA9-F0 Quality Level2 Requested - Forced Idle (no throttle response) requested
P2BA9-68 Quality Level2 Enacted - Forced Idle (no throttle response) enacted
P2BA9-92 Quality Level1 Enacted 25% (Torque derate enacted)
P2BA9-94 Tamper Level1 Requested 25% (Torque derate requested)
P2BAA
Engine > Fault Codes > P2BAA

Information
Service Procedure

DEF consumption
An error has been detected with the DEF consumption level.
Information

Warning light.

Faulty dosing module.
Service Procedure
4. Perform DEF fluid quality Testing.

P2BAA-00 Consumption Warning Requested
P2BAA-F0 Consumption Level2 Requested - Forced Idle (no throttle response) requested
P2BAA-68 Consumption Level2 Enacted - Forced Idle (no throttle response) enacted
P2BAA-92 Consumption Level1 Enacted (25% torque derate enacted)
P2BAA-94 Consumption Level1 Requested (25% torque derate requested)
P2BAB
Engine > Fault Codes > P2BAB
Information
Service Procedure

Exhaust gas recirculation
An error has been detected with the exhaust gas recirculation control unit.
Information
ECU Engine ECU.

Warning light.
Possible Cause Engine related fault affecting EGR flow (intake throttle, EGR, VGT, coolant
temperature, blocked SCR catalyst).
Service Procedure

P2BAB-00 EGR warning requested
P2BAB-F0 EGR level 2 requested - Forced Idle (no throttle response) requested
P2BAB-68 EGR level 2 enacted - Forced Idle (no throttle response) enacted
P2BAB-92 EGR level 1 enacted (25% torque derate enacted)
P2BAB-94 EGR level 1 requested (25% torque derate requested)
P2BAE
Engine > Fault Codes > P2BAE
Information
Service Procedure

Aftertreatment system tampering
An error has been detected which suggests the aftertreatment system is working outside its design parameter.
Information

Warning light.
Possible Cause Exhaust aftertreatment system has been modified or tampered with.
Repeat faults.
Service Procedure
1. Check for signs of tampering, and additional fault codes. Correct as required.

P2BAE-00 Tamper warning requested
P2BAE-F0 Tamper level 2 requested - Forced idle (no throttle response) requested
P2BAE-68 Tamper level 2 enacted - Forced idle (no throttle response) enacted
P2BAE-92 Tamper level 1 enacted (25% torque derate enacted)
P2BAE-94 Tamper level 1 requested (25% torque derate requested)
P3401

Information
Service Procedure

DEF property
Excessive/ambient temperature for aftertreatment 1 SCR catalyst.
Information
Effect Error code.
Possible Cause Faulty head unit.

Faulty coolant valve.
Excessive local ambient temperature.
Excessive temperature of DEF in return line.
Faulty temperature sensor.
Service Procedure
connector sealing.
3. Check the DEF quality is within tolerance. Refer to DEF Quality Test. If the DEF quality is within tolerance,
replace the head unit.

P3402

Information
Service Procedure

DEF property
High concentration error has been detected for aftertreatment 1 SCR catalyst DEF properties.
Information
Effect Error code.
Possible Cause Faulty quality sensor.

Debris in DEF tank.
Coolant leak into DEF tank.
Contamination of DEF supplied to tank.
Addition of fluids other than DEF to tank.
Service Procedure
connector sealing.

P3403

Information
Service Procedure

DEF property
Low concentration error has been detected for aftertreatment 1 SCR catalyst DEF properties.
Information
Effect Error code.

Debris in DEF tank.
Coolant leak into DEF tank.
Contamination of DEF supplied to tank.
Addition of fluids other than DEF to tank.
Service Procedure
connector sealing.

P3404

Information
Service Procedure

DEF property
An error has been detected for aftertreatment 1 SCR catalyst.
Information
Effect Error code.
Possible Cause Faulty coolant valve.

Service Procedure
connector sealing.

P3405

Information
Service Procedure

DEF property
High temperature error for aftertreatment 1 SCR catalyst.
Information
Effect Error code.

Service Procedure
connector sealing.

P3406

Information
Service Procedure

DEF property
Low temperature error for aftertreatment 1 SCR catalyst.
Information
Effect Error code.

Very low local ambient temperature.
Service Procedure
connector sealing.

P3407

Information
Service Procedure

DEF temperature
Open circuit sensor error has been detected for aftertreatment1 SCR catalyst.
Information
Effect Error code.

Service Procedure
connector sealing.

P3408

Information
Service Procedure

DEF temperature
Sensor short circuit error has been detected for aftertreatment1 SCR catalyst.
Information
Effect Error code.

Service Procedure
connector sealing.

P3409

Information
Service Procedure

DEF properties
Excessive ambient/operating level error has been detected for aftertreatment 1 SCR catalyst.
Information
Effect Error code.
Possible Cause Excessive ambient temperature.

Service Procedure
connector sealing.

P3410

Information
Service Procedure

DEF properties
High DEF level error has been detected for aftertreatment 1 SCR DEF properties.
Information
Effect Error code.

Service Procedure
connector sealing.

P3411

Information
Service Procedure

DEF properties
An error with the regent level too low for aftertreatment 1 SCR catalyst has been detected.
Information
Effect Error code.
Service Procedure
connector sealing.

P3412

Information
Service Procedure

DEF temperature
Tank level open circuit error has been detected for aftertreatment1 SCR catalyst
Information
Effect Error code.
Service Procedure
connector sealing.

P3413

Information
Service Procedure

DEF temperature
A short circuit error has been detected for aftertreatment 1 SCR catalyst.
Information
Effect Error code.
Service Procedure
connector sealing.

P3414

Information
Service Procedure

Engine ECU for boost pressure
Erroneous signal for engine boost pressure.
Information
Effect Error code.
Service Procedure
connector sealing.

P3415

Information
Service Procedure

IC1 frame
Data length error for IC1 frame has been detected.
Information
Effect Error code.
Service Procedure
connector sealing.

P3416

Information
Service Procedure

IC1 frame
Time out error for IC1 frame has been detected.
Information
Effect Error code.
Service Procedure
connector sealing.

P3417

Information
Service Procedure

Intake temperature
Erroneous signal has been detected for Intake manifold temperature.
Information
ECU Engine ECU
Effect Error code.
Service Procedure
connector sealing.

P3418

Information
Service Procedure

Operation mode
Erroneous signal has been detected for operating mode request.
Information
Effect Error code.

Refresh function will not recognise the mode and wont start.
Service Procedure
connector sealing.
3. Complete the testing procedure described in the component page Engine ECU.

P3419

Information
Service Procedure

Particulate inlet pressure
An error has been detected with the particulate inlet pressure.
Information
Effect Error code.
Possible Cause DPF sensor value wrongly transmitted.
Service Procedure
connector sealing.
3. Complete the testing procedure described in the component page Engine ECU.

P3420

Information
Service Procedure

Refresh error
Data length error for PROSCR3 frame received for refresh.
Information
Effect Error code.
Service Procedure
connector sealing.

P3420-87 Missing CAN message from Engine ECU
P3421

Information
Service Procedure

Refresh error
Time out error for PROSCR3 frame received for refresh.
Information
Effect Error code.
Service Procedure
connector sealing.

P3421-87 Missing CAN message from Engine ECU
P3422

Information
Service Procedure

Soot load
Communication error, erroneous signal detcted from the CAN
Information
Effect Error code.
Service Procedure
connector sealing.

P3423

Information
Service Procedure

Exhaust gas
Erroneous signal has been detected for engine exhaust gas temperature.
Information
Effect Error code.
Service Procedure
connector sealing.

P3424

Information
Service Procedure

SCR catalyst status very high
Information
ECU Engine ECU.
Effect Fault code.
Possible Cause SCR running refresh not successful.
Service Procedure
1. Perform the exhaust aftertreatment catalyst refresh procedure immediately. Refer to the machine operators
manual.

P3424-85 SCR catalyst partially blocked (overloaded). Signal above allowable range.
P3425

Information
Service Procedure

SCR catalyst status critical
Information
ECU Engine ECU.
Effect Reduced Power Mode (Engine Derate), forced idle.
Possible Cause SCR running refresh not successful.
Service Procedure
1. Perform the exhaust aftertreatment catalyst refresh procedure immediately. Refer to the machine operators
manual.

P3425-85 SCR catalyst fully blocked (plugged). Signal above allowable range.
U0001
Engine > Fault Codes > U0001

Information
Service Procedure

High speed CAN communication bus
CAN Communication Error.
Information
ECU Engine ECU.
Effect
Service Procedure
connector sealing.

U0001-00 No sub type information
U0029

Information
Service Procedure

Error 250KbPs
An error with the CANBUS has been detected.
Information
ECU Engine ECU/ aftertreatment ECU.
Service Procedure
connector sealing.

U0029-87 CANBUS missing message (CANBBUS off error 250kbps)
U0029-88 CANBUS off (CANBBUS off error 250kbps)
U0073

Information
Service Procedure

Control module communication bus A off
An error with the CANBUS has been detected.
Information
Service Procedure
connector sealing.

U0073-81 Received network data in error.
U0100

Information
Service Procedure

Lost Communication with ECM/PCM "A"
Fault on the CAN communication network.
Information
Service Procedure
connector sealing.

U0100-81 Received network data in error.
U0105

Information
Service Procedure

Fuel quantity from engine ECU
Error with the fuel quantity.
Information
Service Procedure
connector sealing.

U0105-87 Missing CAN message from engine ECU
U010A
Engine > Fault Codes > U010A

Information
Service Procedure

Lost communication with Exhaust Gas Recirculation (EGR) control module
Information
Service Procedure
connector sealing.

U010A-81 Received network data in error
U010A-88 Bus off
U010C
Engine > Fault Codes > U010C
Information
Service Procedure

Lost communication with turbocharger/supercharger module "A"
Information
Service Procedure
connector sealing.

U010C-81 Received network data in error
U010C-88 Bus off
U010E
Engine > Fault Codes > U010E

Information
Service Procedure

Engine ECU/aftertreatment system ECU Communication
Communication error between the engine ECU and aftertreatment system ECU
Information
Effect Reduced Power Mode (Engine Derate) forced idle.
Possible Cause Repeat offence.

Faulty ECU.
Service Procedure
connector sealing.

Fault Description
Code
U010E- U010E FTB 0x87 Inducement BAM message time out. Missing message on CAN B, the 500k bus.
08 1. This fault is raised by the engine ECU when the Inducement BAM message sent from the DCU
has not been received by the engine ECU.
2. This message is on the 500k Dieselmax Engine CAN (that does the VGT, EGR, and now also
the Nox sensors and DEF tank header).
3. The DCU is not working, or not powered.
1. SM fault routines to test if the DCU is powered.
1. From the SM diag tool engine Aftertreatment System.
1. Check the "Aftertreatment ECU Connection" indicator on the Aftertreatment
System screen is green (not red)
1. A green indicator means the DCU is powered, with working software, and
communicating on the 250k CAN A machine CAN bus.
2. A red indicator means the DCU is either;
1. Not responding to Servicemaster requests. Restart SM, and
powercycle ECU.
2. Not powered. Ignition or power supply issue.
3. Does not have working software installed. Reflash.
3. There is a wiring fault with the 500k CAN bus.
4. SM fault routines to test the 500k CAN bus.
4. From SM engine ECU diag tool fault code screen, check for CAN
faults from: DCU, EGR, VGT.
2. Message time-outs from more than one module would indicate a fault with the 500k
CAN bus in to the engine ECU.

5. From SM DCU diag tool fault code screen, check for CAN faults from:
ECU, Nox sensors, DEF tank header,
3. Message time-outs from more than one module would indicate a fault with the 500k
CAN bus in to the DCU.
U010C- U010E FTB 0x08 Engine Rating message time out. Missing message on CANA, the 250k bus.
87 1. This fault is raised by the engine ECU when the power rating message sent from the DCU has
not been received by the engine ECU.
2. This message is on the 250k machine CAN bus.
3. The DCU is not working, or not powered.
1. SM fault routines to test if the DCU is powered.
1. From the SM diag tool engine Aftertreatment System (was aftertreatment System)
screen,
1. Not responding to Servicemaster requests. Restart SM, and
powercycle ECU.
3. There is a wiring fault with the 250k CAN bus.
4. SM fault routines to test the 250k CAN bus.
4. From the SM diag tool engine Aftertreatment System (was SCR
System) screen,
2. Check there are values displayed and the values change as the engine is run and/or
the ignition is cycled.
2. Frozen or blank values means SM ins not able to communicated with the DCU.
5. Not responding to Servicemaster requests. Restart SM, and powercycle
ECU.
8. Is not connected to the 250k CAN bus. Wiring issue.
11. Not responding to Servicemaster requests. Restart SM, and powercycle
ECU.
U0121

Information
Service Procedure

Lost communication with Anti Lock Brake (ABS) control module
Information
Service Procedure
connector sealing.

U0121-81 Received network data in error
U0140

Information
Service Procedure

Lost communication with Machine ECU.
Aftertreatment refresh inhibit/force switch message missing.
Information
ECU Engine ECU.
Effect Reduced Power Mode (Engine Derate), forced idle.

Inducement code P2BAB-00 may be generated if SCR catylst refresh is unable
to be performed.

Incorrect ECU software.
Faulty ECU.
Service Procedure

Fault Description
Code
U0140-87 1. This fault is raised by the engine ECU when the CM1 message sent from the Body Control
Module has not been received by the engine ECU.
2. This message is on the 250k machine CAN bus.
3. The Body Control Module is not working, or not powered.
U0401

Information
Service Procedure

Lost communication with Anti Lock Brake (ABS) control module
Information
ECU Engine ECU.
Service Procedure
connector sealing.

U0401-00 No sub type information
U0401-61 Signal calculation error (CAN BUS message error for modeled NOx from engine ECU)
U0401-81 Invalid signal data received (CAN BUS message error from engine ECU)
U0401-86 Signal invalid (CAN BUS message error from engine ECU)
U0401-87 Missing CAN message from ECU
U040B
Engine > Fault Codes > U040B

Information
Service Procedure

Invalid data received from Exhaust Gas Recirculation (EGR) control module
Information
ECU Engine ECU.
Service Procedure
connector sealing.

U040B-00 EGR Power-up span out of range
U040B-96 EGR Actuator internal hardware error
U040B-97 EGR Valve or mechanism obstruction
U040B-98 EGR Actuator over temperature warning (> 120°C)
U040B-4B EGR Actuator over temperature alarm (> 130°C)
P0400-00 Fault on the exhaust gas recirculation (EGR) control system
U040D
Engine > Fault Codes > U040D

Information
Service Procedure

Fault with Variable Geometry Turbochanger
Fault detected with the VGT electrical or mechanical system
Information
Possible Cause VGT mechanism seized, damaged or obstructed.

Actuator coolant flow blocked / restricted or low coolant level.
Actuator internal electrical fault.
Service Procedure
1. Complete the testing procedure described on the component page Variable Geometry Turbocharger (VGT).
connector sealing.

U040D-00 VGT Calibration span out of range
U040D-54 VGT Power-up span out of range
U040D-81 VGT CAN communication error
U040D-96 VGT Actuator internal error
U040D-97 VGT Mechanism obstruction
U040D-98 VGT Actuator over temperature
P0400-00 Fault on the exhaust gas recirculation (EGR) control system.
U040F
Engine > Fault Codes > U040F

Information
Service Procedure

Engine rating mismatch
Error with a DCU message containing the engine power rating, it does not match that of the engine calibration.
Information
Possible Cause Repeat offence.

DCU or ECU had been swapped from another machine or re-flashed
incorrectly.
Service Procedure
1. Using the SM tool, General tab, check the Engine System Number (ESN) values are the same for both the
ECU and DCU.
2. Flash the DCU and/or Engine ECU with the correct software for the machine.
3. Refer to the Re-flashing an ECU help page for more information

Fault Description
Code
U040F- U040F Engine power rating mismatch.

81 1. This fault code is raised by the engine ECU when a message from the DCU containing the
engine power rating is received by the engine ECU, but the power rating does not match that
contained in the engine calibration.
2. The CAN message has been received correctly by the engine ECU, there is not a problem with
the wiring.
3. The CAN message is on the 250k machine CAN bus.
4. The DCU is calibrated to contain the engine power, and the engine ECU is also calibrated to
match the engine power rating. (Note, this is not the SM Setup Tool engine power).
5. The fault is that the DCU calibration does not match the ECU calibration power rating.
1. A DCU or ECU has been swapped from another machine.
2. The machine has not been built correctly.
1. Using SM Setup Tool, General Tab. Check the ESN values are the same for both
engine ECU and DCU.
2. Flash the DCU and/or the engine ECU with the correct software for the machine.
3. The system has been tampered with.
3. Check for tampering such as after market ECUs on the 250k machine CAN bus.
U059E
Engine > Fault Codes > U059E

Information
Service Procedure

CAN BUS communication error for messages from upstream NOx sensor to aftertreatment ECU.
An error has been detected with the upstream NOx sensor Can communication signal.
Information
Possible Cause Sensor unplugged from harness.

Faulty sensor.
NOx sensors, DEF tank, EGR and VGT all communicate on the same 500 BPS CAN BUS wires. The CAN BUS
consists of a CAN high and a CAN low wire.
Service Procedure
connector sealing.

Fault Descriptions
Code
U059E-00 No sub type information (CAN BUS message error for temp signal status from downstream NOx
sensor)
U059E-02 General signal failure (CAN BUS message error for NO2 level from upstream NOx sensor)
U059E-08 Bus signal/Message failure (CAN BUS message error for O2 signal status from upstream NOx
sensor)
U059E-9A Component or system operation conditions (CAN BUS message error for heater ratio from upstream
NOx sensor)
U059E-29 Signal invalid (CAN BUS message error from upstream NOx sensor)
U059E-62 Signal compare failure (CAN BUS message error for NH3 level from upstream NOx sensor)
U059E-81 Invalid serial data received (CAN BUS message error from upstream NOx sensor)
U059E-84 Signal below allowable range (CAN BUS message error for power signal status from upstream NOx
sensor)
U059E-86 Signal invalid (CAN BUS message error from upstream NOx sensor)
U059E-87 Missing CAN message from ECU (CAN BUS off error from upstream NOx sensor)
U059E-93 No operation (CAN BUS message error for NOx level from upstream NOx sensor)
U059E-94 Unexpected operation (CAN BUS message for error for O2 level from upstream NOx sensor)
U059E-97 Component or system operation obstructed or blocked (CAN BUS message error for NOx signal
status from upstream NOx sensor)
U059F
Engine > Fault Codes > U059F

Information
Service Procedure

CAN BUS communication error for messages from downstream NOx sensor to aftertreatment
ECU.
An error has been detected with the downstream NOx sensor CAN communication signal.
Information

Sensor unplugged from harness.
NOx sensors, DEF tank, EGR and VGT all communicate on the same 500 BPS CAN BUS wires. The CAN BUS
consists of a CAN high and a CAN low wire.
Service Procedure
connector sealing.

Fault Descriptions
Code
U059F-00 No sub type information (CAN BUS message error for temp signal status from upstream NOx
sensor)
U059F-02 General signal failure (CAN BUS message error for no2 level from downstream NOx sensor)
U059F-08 Bus signal/Message failure (CAN BUS message error for o2 signal status from downstream NOx
sensor)
U059F-9A Component or system operating conditions (CAN BUS message error for heater ratio from
downstream NOx sensor)
U059F-29 Signal invalid (CAN BUS message error from downstream NOx sensor)
U059F-62 Signal compare failure (CAN BUS message error for nh3level from downstream NOx sensor)
U059F-81 Invalid serial data received (CAN BUS message error from downstream NOx sensor)
U059F-84 Signal below allowable range (CAN BUS message error for power signal status from downstream
NOx sensor)
U059F-86 Signal invalid (CAN BUS message error from downstream NOx sensor)
U059F-87 Missing CAN message from engine ECU (CAN BUS off error from downstream NOx sensor)
U059F-93 No operation (CAN BUS message error for NOx level from downstream NOx sensor)
U059F-94 Unexpected operation (CAN BUS message error for o2 level from downstream NOx sensor)
U059F-97 Component or system operation obstructed or blocked (CAN BUS message error for NOx signal
status from downstream NOx sensor)
U3FFF
Engine > Fault Codes > U3FFF

Information
Service Procedure

SAE DTC does not exist - will require manufacturer's specific information
Information
Service Procedure
connector sealing.

U3FFF-00 No sub type Information

Jcb Tier 4 Troubleshooting Codes

Uploaded by

Copyright:

Available Formats

Jcb Tier 4 Troubleshooting Codes

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Jcb Tier 4 Troubleshooting Codes

Uploaded by

Copyright:

Available Formats

Fault Codes Page 1 of 319

JCB EcoMAX Help Files

Engine > Fault Codes

JCB EcoMAX Help Files

Fault Code Background Information

Engine > Fault Codes > Fault Code Background Information

Fault Code Structure

00 No sub type information

02 General signal failure

04 System internal failure (ECU)

05 System programming failure

11 Short Circuit to Ground (SC2G)

12 Short Circuit to Battery (SC2VBAT)

13 Open Circuit (OC)

16 Circuit voltage below threshold

17 Circuit voltage above threshold

18 Circuit current below threshold

19 Circuit current above threshold

1A Circuit resistance above threshold

1B Circuit resistance below threshold

1C Circuit voltage out of range

23 Signal stuck low

24 Signal stuck high

26 Signal rate of change below threshold

27 Signal rate of change above threshold

36 Signal frequency too low

37 Signal frequency too high

38 Signal frequency incorrect

45 Programme memory failure

46 Calibration / Parameter memory failure

47 Watchdog / micro-controller / microprocessor failure

64 Signal plausibility failure

62 Signal compare failure

72 Actuator stuck open

73 Actuator stuck closed

81 Received Network Data in Error

85 Signal above allowable range

86 CAN Signal invalid

9A Component or System Operating Conditions

92 Performance or incorrect operation

96 Component or Internal Failure

97 Component or System Operation Obstructed or Blocked

98 Component of System Over Temperature

JCB EcoMAX Help Files

Engine > Fault Codes > P0001

Fault Code Description

Fault Code Description

Effect Reduced Power Mode (Engine Derate) torque reduction.

Possible Cause Damaged harness or harness connectors.

Related Fault FTB Codes

P0001-13 Open circuit

This topic last edited on 27/05/2016

JCB EcoMAX Help Files

Engine > Fault Codes > P0002

Fault Code Description

Fault Code Description

Effect Reduced Power Mode (Engine Derate) torque reduction.

Possible Cause Damaged harness or harness connectors.

Related Fault FTB Codes

P0002-12 Short circuit to battery (SC2VBAT)