Eight-port offline T-8000C manual
一、T-8000C system features
1、32—256 Gray, Gamma correction procession software
2、Combined with video encoding and broadcasting software LedEdit , support rules and
specific-shaped handle, and other points, line lights source
3、Eight-port output，port 512/1024 lights
4、Playback content stored in SD card, can stand-alone play, also multiple cascade
NOTE：T-8000C port 512 lights, the playback speed of up to 30 frames / sec, the port more than
512 lights, the frame rate with the increase in the number of lights automatically reduced.
5、When multiple cascade, only the first controller buttons work, followed by sub-control
buttons are automatically shielded, at this point can adjust playback file and speed through
the first controller
NOTE：At this time the first controller's buttons can control all sub-control keys
Support chips：
Support chips LedEdit Single one Remarks
corresponding model support lights
LPD6803,D705,1101,6909,6 T-8000C-6803 8192pixels
912
LPD8806,LPD8809 T-8000C-8806 8192 pixels
TM1803,TM1804,TM1809, T-8000C-TM 8192 pixels TM1804 and
TM1812 TM1809 are
divided into high
and low speed
DMX512 T-8000C-DMX 1360/4096 pixels Compatible with
standard
DMX512
agreement
WS2801,WS2803 T-8000C-WS 8192 pixels
TLS3001,TLS3002 T-8000C-TLS 8192 pixels
P9813 T-8000C-P9813 8192 pixels
SM16715 T-8000C-SM16715 8192 pixels
SM16716 SM16726B T-8000C-SM16716 8192 pixels
BS0815 T-8000C-0815 8192 pixels
二、System Architecture
When T8000C as single use, can store up to 16 files, copy multiple files to SD card in order
If multiple cascade, Software will automatically generate multiple*.led files below the project,
then load the respective *. Led to the controller correspondingly. (Generated multiple *. led
are below the new Led directory)
三、File storage：
1、Program 0 file:
2、program 1 file :
File name format is: MM_N.led, MM on behalf of program code that is which program.
N represents the controller number.
Program numbered from 0, namely:
The 0 program is：00_1.led,00_2.led,00_3.led……
The 1st program is：01_1.led,01_2.led,01_3.led……
……
The 16th program is：16_1.led,16_2.led,16_3.led……
The relation between program and controller is：
Programs placed in the 1st controller is:00_1.led,01_1.led,02_1.led……
Programs placed in the 2nd controller is：00_2.led,01_2.led,02_2.led……
……
Programs placed in the 16th controller is：00_16.led,01_16.led,02_16.led…
四、Output picture：
图一 图二
①TTL signal（245 signal）：
COM GND(ground)
DAT Signal
CLK Clock
NOTE：TTL signal output for the controller and the lighting must be common ground (that is,
the ground controller output and the lamp connected to the ground together)
②If the customer needs can also be replaced with differential output, differential
outputs defined as (485 differential)：
COM GND(ground)
DAT Differential signal A(or
DAT+)
CLK Differential signal B(or
DAT-)
NOTE：Differential signal do not share ground
③If the controller output to the lamp is distant, you can use the current loop output
(current loop transmission distance up to 300m), is defined as follows
COM Common port（not GND)
DAT Signal
CLK Clock
NOTE：Use the current loop output, must connect a current loop receiver board before the
lamp, then connect lamps。
The identity at the top of the controller：
DC5V +5V power input
POWER Power indicator
ERROR Error indicator
SYNC Cascade synchronization signal
indicator
SD CARD SD card slot
Two Ethernet ports in front of the controller are synchronization signal interface for cascade：
IN sync signal input
OUT sync signal output
NOTE ： This cascade lines can use standard
straight-through cable, between the two controllers
can be cascaded up to 100 meters distance.
Buttons definition：
SPEED- Speed down Press these two buttons at the same time,
SPEED+ Speed up multiple files in the SD card can be
looped
MODE Switch files
SET Save settings(if press SET，the current settings file and
playback speed are saved, according to this to play after
the next boot)
NOTE：When multiple cascade, only the first controller buttons work, followed by sub-control
buttons are automatically shielded, at this point can adjust playback file and speed through
the first controller
NOTE：At this time the first controller's buttons can control all sub-control keys
Special parameters：
Memory card：
Type：SD card（if control more lights, suggest using high-speed SD card）
Capacity：256MB—2GB
Format：FAT format
Store file：*.led
Physical parameters：
Temperature：-20℃—85℃
Power supply：DC 5V input
Power：4W
NOTE：
To copy files to SD card ，you must first format the SD card, pay attention to is that
each copy must be formatted before. SD card must be formatted as FAT format
The SD card in controller can not be hot-swappable, plug the SD card every time, you must
first disconnect the power supply
