Remote I/O Communication Module

Specification and Installation Instructions

Models
CMMB1020

Description
The CMMB1020 extends your BACnet or Modbus network when
your application requires additional inputs and outputs on a physical
controller. Capitalizing on the high-density I/O point count of 30
universal inputs and 20 outputs enables the CMMB1020 to provide a
cost effective yet advanced integration capability.

Features CMMB1020

Power & Communication

Network Communication
• 24Vac or 24Vdc supply
• BACnet® MS/TP or Modbus communication port (selectable) • BACnet® MS/TP or Modbus communication ports
(selectable via DIP switch)
Inputs & Outputs
• Select MAC address via DIP switch or via network
• 30 universal inputs
• 4 universal outputs BACnet®
• 4 analog outputs • MS/TP @ 9600, 19200, 38400, 76800 or 115000 bps
• 12 binary outputs • Automatic baud rate detection
• Automatic device instance configuration
Installation
• Improved BACnet Stack
• LED status indication of each output
• Firmware upgradable via BACnet
• DIN rail mounting
• Expansion slot for connection to Neptronic RPB
• Removable, non-strip, raising clamp terminals BACnet Router
Other Modbus
• 16-bit A/D Converter for greater resolution • Modbus @ 9600, 19200, 38400 or 57600 bps
• Supports Pt1000 and Ni1000 • RTU Slave, 8 bits (configurable parity and stop bits)
• Connects to any Modbus master

Technical Specifications
Specifications CMMB1020
Input Voltage 24 Vac/Vdc ±10%
Consumption 12VA
Universal Inputs 30 [0-10Vdc, 2-10Vdc, Thermistor, on/off (dry contact), 0-20mA, 4-20mA] / 16-bit resolution
Universal Outputs 4 [0-10Vdc, on/off] / 12-bit resolution
Analog Outputs 4 [0-10Vdc] / 12-bit resolution
Digital Relay Binary Outputs 12 [normally open, independent common per relay, 5A resistive]
Service Port BACnet® MS/TP @ 38400 bps
BACnet® MS/TP @ 9600, 19200, 38400, 76800 or 115000 bps (BAS-C).
Modbus RTU slave @ 9600, 19200, 38400 or 57600.
Selectable parity and stop bit configuration:
Communication Port
• No parity, 2 stop bit
• Even parity, 1 stop bit
• Odd parity, 1 stop bit
Communication Connections 24 AWG twisted-shield cable (Belden 9841 or equivalent)
Electrical Connections 0.8 mm2 [18 AWG] minimum
Operational Temperature 0ºC to 50ºC [32ºF to 122ºF]
Storage Temperature -30ºC to 50ºC [-22ºF to 122ºF]
Relative Humidity 5 to 95% non condensed
Weight 0.6 kg [1.3 lb]
Dimensions A C

A = 9.18” / 233 mm
B = 4.93” / 125 mm
C = 2.27” / 58 mm B

CMMB1020-211124-ESA Page | 1
 Remote I/O Communication Module
Specification and Installation Instructions

Connections and Configurations

Please note that all jumper settings must also be set to the same value through BACnet. Some additional configurations are only
available through BACnet.

Baud Rate | DS2 Network | DS2 MAC Address | DS1 UO1-UO4 Selector | JP3-JP6 End of Line | JP1-JP2

2 3 4 Result 1 Mode The 8 DIP switches represent a binary Analog Output 120 Ohms*
OFF OFF OFF Auto Detect OFF BACnet logic to calculate the MAC address. None
ON OFF OFF 9600 ON Modbus* * default setting
OFF ON OFF 19,200 * default setting Default = 101 Binary Output*
ON ON OFF 38,400
OFF OFF ON 57,600* BACnet all OFF = 0 * default setting

ON OFF ON 76,800** Modbus all OFF = 1

OFF ON ON 115,200**
* default setting
** only available for BACnet

Service Port | TB1

Modbus Mode Options | DS2 ** Baud rate of 38,400 bps **

POWER COM: Common

5 6 Result RXD COM B-: BACnet B-
STATUS
DS2 DS1 A+: BACnet A+
OFF OFF No parity, 2 stop bits* 1
ON
1
ON
B-
OFF ON Even parity, 1 stop bit 2 2 JP1
3 3
ON OFF Odd parity, 1 stop bit 4
5
4
5 TXD
A+ COM Port | TB2
6 6
* default setting 7 7 ** Baud rate and MAC address
Not Used 8 8 RXD COM
based on DS1 & DS2 selection **
AI1 B-
Universal Inputs | TB10-17 JP2 COM: Common
** Selectable ** AI2 A+ B-: BACnet/Modbus B-
TXD
A+: BACnet/Modbus A+
AI1: Universal Input 1 COM AO1
AI2: Universal Input 2 AO2 Analog Outputs | TB3
AI3
COM: Common ** 0-10 Vdc (1.5mA max) **
AI3: Universal Input 3 AI4 AO COM
AI4: Universal Input 4 AO3 AO1: Analog Output 1
AI5 AO2: Analog Output 2
AO4 AO COM: Common
AI5: Universal Input 5 AI6
AI6: Universal Input 6 AO3: Analog Output 3
COM
COM: Common COM JP3 UO1 AO4: Analog Output 4
AI7: Universal Input 7 NO
AI7 Universal Outputs | TB4-5
AI8: Universal Input 8
COM ** 350mA max (each) **
AI8 JP4 UO2
AI9: Universal Input 9 NO
AI10: Universal Input 10 AI9 COM: Relay Common
COM: Common COM NO: Normally Open
AI10 UO3
AI11: Universal Input 11 JP5 NO
AI12: Universal Input 12 COM
AI11 COM
AI13: Universal Input 13 UO4
JP6 NO
AI14: Universal Input 14 AI12
COM: Common Binary Outputs | TB6-9
AI15: Universal Input 15 AI13 NO
BO1 NO: Normally Open
AI16: Universal Input 16 AI14 COM COM: Relay Common
AI17: Universal Input 17 COM NO
AI18: Universal Input 18 BO2
AI15 COM
COM: Common
AI19: Universal Input 19 AI16 NO
AI20: Universal Input 20 BO3
AI17 COM
AI21: Universal Input 21 AI18
AI22: Universal Input 22 NO
COM: Common COM BO4
COM
AI23: Universal Input 23
AI19
AI24: Universal Input 24 NO
AI20 BO5
AI25: Universal Input 25 COM
AI26: Universal Input 26 AI21
NO
COM: Common
AI22 BO6
AI27: Universal Input 27 COM
AI28: Universal Input 28 COM
NO
AI29: Universal Input 29 AI23 BO7
COM
AI30: Universal Input 30 AI24
COM: Common NO
COM: Common AI25 BO8
AI26 COM
NO
COM BO9
AI27 COM

AI28 NO
BO10
AI29 COM

NO
AI30 BO11
COM
COM
NO
COM BO12
Power Input | TB18 COM
** 500mA max ** COM PCB POWER

COM: Common (GND) 24V

24V: 24Vac or 24Vdc

www.neptronic.com Page | 2
 Remote I/O Communication Module
Specification and Installation Instructions

FCC Compliance

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

MAC Address DIP Switch (DS1)

MAC address for BACnet and Modbus communication, are selectable by DIP switch DS1 using binary logic.

BACnet
• Highest MAC address is 254.
• Default is all switches OFF = MAC address 0
• If you do not change device instance in program mode, it will be automatically modified according to the MAC address.

MAC Address DS.1 = 1 DS.2 = 2 DS.3 = 4 DS.4 = 8 DS.5 = 16 DS.6 = 32 DS.7 = 64 DS.8 = 128 Default Device Instance
0 OFF OFF OFF OFF OFF OFF OFF OFF 153000
1 ON OFF OFF OFF OFF OFF OFF OFF 153001
2 OFF ON OFF OFF OFF OFF OFF OFF 153002
3 ON ON OFF OFF OFF OFF OFF OFF 153003
4 OFF OFF ON OFF OFF OFF OFF OFF 153004
… … … … … … … … … …
126 OFF ON ON ON ON ON ON OFF 153126
… … … … … … … … … …
254 OFF ON ON ON ON ON ON ON 153254

Modbus
• Highest MAC address is 247.
• Default is all switches OFF = MAC address 1.
• There is no device instance for Modbus.

MAC Address DS.1 = 1 DS.2 = 2 DS.3 = 4 DS.4 = 8 DS.5 = 16 DS.6 = 32 DS.7 = 64 DS.8 = 128
1 OFF OFF OFF OFF OFF OFF OFF OFF
1 ON OFF OFF OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF OFF OFF
4 OFF OFF ON OFF OFF OFF OFF OFF
… … … … … … … … …
126 OFF ON ON ON ON ON ON OFF
… … … … … … … … …
247 ON ON ON OFF ON ON ON ON

www.neptronic.com Page | 3
 Remote I/O Communication Module
Specification and Installation Instructions

LEDs
POWER
STATUS RXD Power
DS2 DS1
1
ON
1
ON On = Input voltage normal
JP1
2
3
2
3 Off = No power
4 4
5 5 TXD
6
7
6
7
RXD
Status
8 8
Flashing = Normal operation (watchdog)
JP2
RX/TX (BACnet)
TXD
Flashing = Receiving (RX) and/or transmitting (TX) data.
RX/TX (Modbus)
Flashing = Receiving (RX) and/or transmitting (TX) data.
Output Status
On = Activated
Off = Deactivated
JP3
Analog = When Universal and Analog outputs are set
to analog values (Vdc); the LED intensity
corresponds to the output value. For example:
JP4 At 10Vdc, the LED will be fully on. At 5Vdc, the
Output Status LEDs LED will be at 50% intensity. At 0 Vdc, the LED
(one per output) will be off.
JP5

JP6

UO in AO Mode – Wiring Example

AO1
AO2
AO COM -
AO3
AO4
10VDC
COM
JP3
NO
+
COM UO1 when used
JP4
NO as AO5

www.neptronic.com Page | 4
 Remote I/O Communication Module
Specification and Installation Instructions

Modbus Network Conditions

Modbus Registers and their Relevance Based on Different Input Modes
Voltage/Current Mode:
• When UI1 is configured as 0-10VDC or 4-20mA, the raw voltage/current value is seen on register 40012 (Universal
Input 1 Reading).
• The value seen in register 40051 (Universal Input 1 Impedance or Linearization) will be based on the value that is
entered by the user for registers 40118 (Universal Input 1 Minimum Linear Value) and 40119 (Universal Input 1
Maximum Linear Value).
• The register 40115 (Universal Input 1 Linear Value Scale) functions as scaling for the linearized value that you see for
register 40051.
• The range of the sensor/input type (2-10V or 4-20mA) is set by registers 40116 (Universal Input 1 Minimum Voltage)
and 40117 (Universal Input 1 Maximum Voltage) and the linearized value is read on register 40051.
• The register 40120 (Universal Input 1 Linear Value Bias) adds a bias to the value read on register 40051.
• The same is applicable for UI2 to UI30 with the registers corresponding to minimum and maximum voltage and/or linear
values.
Thermistor Mode:
• When UI1 is configured as a temperature sensor, the raw resistance value is seen on register 40051 and the
temperature value based on the type of sensor selected is available on register 40012.
• The user can perform calibration of the temperature value by adding a reading bias on register 40114. The value set
here affects the reading on register 40012.
• The same is applicable for UI2 to UI30 with the registers corresponding to minimum and maximum voltage and/or linear
values.

UO1 to UO4 Operation

• UO1 to UO4 can be configured to operate as an analog output or a binary output using jumpers JP3 to JP6.
• When using UO1 to UO4 as BO13-BO16 through the jumpers, the user must ensure not to write on the registers for
AO5-AO8 as it will interfere with the LED operation and the failsafe modes.
• The failsafe presets for the unused/unrouted outputs (AO5 to AO8) in this case must be set to the value required for
safe operation of the equipment.
• When using UO1 to UO4 as AO5-AO8 through the jumpers, the user must ensure not to write on the bits for BO13-
BO16 as it will interfere with the LED operation and the failsafe modes.
• The failsafe presets for the unused/unrouted outputs (AO5 to AO8) in this case must be set to the value required for
safe operation of the equipment.

Universal Input Mode Default Settings

Cfg UI.x Mode Cfg UI.x Cfg UI.xLinear Cfg UI.x Min Cfg UI.x Max Cfg UI.x Min Cfg UI.x Max Cfg UI.x Linear
(Reg. # for UI1: Reading Bias Value Scale Voltage Voltage Linear Value Linear Value Value Bias
112/40113) (113/40114) (114/40115) (115/40116) (116/40117) (117/40118) (118/40119) (119/40120)
1= "0-10V" N/A 1 0 10000 0 100 0
2= "4-20mA" N/A 1 0 20000 0 100 0
3= "Dry Contact" N/A N/A N/A N/A N/A N/A N/A
4-8 = Thermistors 0 N/A N/A N/A N/A N/A N/A

www.neptronic.com Page | 5
 Remote I/O Communication Module
Specification and Installation Instructions

BACnet Objects Table

ID1 Name Description Writable? Range

0 to 10Volt or -40 to 150ºC or

Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.1 UI1 Reading Universal input 1 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.2 UI2 Reading Universal input 2 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.3 UI3 Reading Universal input 3 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.4 UI4 Reading Universal input 4 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 302ºF or 0 to 20mA or 0 to 1
AI.5 UI5 Reading Universal input 5 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.6 UI6 Reading Universal input 6 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.7 UI7 Reading Universal input 7 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.8 UI8 Reading Universal input 8 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.9 UI9 Reading Universal input 9 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.10 UI10 Reading Universal input 10 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.11 UI11 Reading Universal input 11 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.12 UI12 Reading Universal input 12 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.13 UI13 Reading Universal input 13 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.14 UI14 Reading Universal input 14 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.15 UI15 Reading Universal input 15 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.16 UI16 Reading Universal input 16 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1

1
ID is equal to ObjectType.Instance

www.neptronic.com Page | 6
 Remote I/O Communication Module
Specification and Installation Instructions

ID1 Name Description Writable? Range

0 to 10Volt or -40 to 150ºC or

Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.17 UI17 Reading Universal input 17 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.18 UI18 Reading Universal input 18 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.19 UI19 Reading Universal input 19 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.20 UI20 Reading Universal input 20 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.21 UI21 Reading Universal input 21 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.22 UI22 Reading Universal input 22 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.23 UI23 Reading Universal input 23 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.24 UI24 Reading Universal input 24 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.25 UI25 Reading Universal input 25 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.26 UI26 Reading Universal input 26 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.27 UI27 Reading Universal input 27 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.28 UI28 Reading Universal input 28 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.29 UI29 Reading Universal input 29 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
0 to 10Volt or -40 to 150ºC or
Out of service -40 to 212ºF or 0 to 20mA or 0 to 1
AI.30 UI30 Reading Universal input 30 Reading
COV Increment Resolution: 0.001Volt or 0.01ºC/0.02ºF or
0.001mA or 1
Out of service
AO.1 AO1 Voltage Voltage of analog output 1 0 to 10 Volt | Resolution 0.001 Volt
Present Value
Out of service
AO.2 AO2 Voltage Voltage of analog output 2 0 to 10 Volt | Resolution 0.001 Volt
Present Value
Out of service
AO.3 AO3 Voltage Voltage of analog output 3 0 to 10 Volt | Resolution 0.001 Volt
Present Value
Out of service
AO.4 AO4 Voltage Voltage of analog output 4 0 to 10 Volt | Resolution 0.001 Volt
Present Value
Out of service
AO.5 AO5 Voltage* Voltage of analog output 5 0 to 10 Volt | Resolution 0.001 Volt
Present Value
Out of service
AO.6 AO6 Voltage* Voltage of analog output 6 0 to 10 Volt | Resolution 0.001 Volt
Present Value

www.neptronic.com Page | 7
 Remote I/O Communication Module
Specification and Installation Instructions

ID1 Name Description Writable? Range

Out of service
AO.7 AO7 Voltage* Voltage of analog output 7 0 to 10 Volt | Resolution 0.001 Volt
Present Value
Out of service
AO.8 AO8 Voltage* Voltage of analog output 8 0 to 10 Volt | Resolution 0.001 Volt
Present Value
0 to 100% or 0 to 806800 ohms
AV.1 UI1 Impedance Universal Input 1 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.2 UI2 Impedance Universal Input 2 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.3 UI3 Impedance Universal Input 3 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.4 UI4 Impedance Universal Input 4 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.5 UI5 Impedance Universal Input 5 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.6 UI6 Impedance Universal Input 6 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.7 UI7 Impedance Universal Input 7 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.8 UI8 Impedance Universal Input 8 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.9 UI9 Impedance Universal Input 9 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.10 UI10 Impedance Universal Input 10 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.11 UI11 Impedance Universal Input 11 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.12 UI12 Impedance Universal Input 12 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.13 UI13 Impedance Universal Input 13 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.14 UI14 Impedance Universal Input 14 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.15 UI15 Impedance Universal Input 15 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.16 UI16 Impedance Universal Input 16 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.17 UI17 Impedance Universal Input 17 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.18 UI18 Impedance Universal Input 18 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.19 UI19 Impedance Universal Input 19 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.20 UI20 Impedance Universal Input 20 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.21 UI21 Impedance Universal Input 21 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.22 UI22 Impedance Universal Input 22 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.23 UI23 Impedance Universal Input 23 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.24 UI24 Impedance Universal Input 24 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.25 UI25 Impedance Universal Input 25 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.26 UI26 Impedance Universal Input 26 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.27 UI27 Impedance Universal Input 27 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.28 UI28 Impedance Universal Input 28 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.29 UI29 Impedance Universal Input 29 Impedance Out of service
Resolution: 1% or 1 ohms
0 to 100% or 0 to 806800 ohms
AV.30 UI30 Impedance Universal Input 30 Impedance Out of service
Resolution: 1% or 1 ohms

www.neptronic.com Page | 8
 Remote I/O Communication Module
Specification and Installation Instructions

ID1 Name Description Writable? Range

Out of service
AV.31 Cfg AO1 Failsafe Preset Failsafe preset for analog output 1 0 to 10Volt | Resolution: 0.001Volt
Present Value
Out of service
AV.32 Cfg AO2 Failsafe Preset Failsafe preset for analog output 2 0 to 10Volt | Resolution: 0.001Volt
Present Value
Out of service
AV.33 Cfg AO3 Failsafe Preset Failsafe preset for analog output 3 0 to 10Volt | Resolution: 0.001Volt
Present Value
Out of service
AV.34 Cfg AO4 Failsafe Preset Failsafe preset for analog output 4 0 to 10Volt | Resolution: 0.001Volt
Present Value
Out of service
AV.35 Cfg AO5 Failsafe Preset* Failsafe preset for analog output 5 0 to 10Volt | Resolution: 0.001Volt
Present Value
Out of service
AV.36 Cfg AO6 Failsafe Preset* Failsafe preset for analog output 6 0 to 10Volt | Resolution: 0.001Volt
Present Value
Out of service
AV.37 Cfg AO7 Failsafe Preset* Failsafe preset for analog output 7 0 to 10Volt | Resolution: 0.001Volt
Present Value
Out of service
AV.38 Cfg AO8 Failsafe Preset* Failsafe preset for analog output 8 0 to 10Volt | Resolution: 0.001Volt
Present Value
Out of service 0 = Open
BO.1 BO1 State Binary Output 1 State
Present Value 1 = Closed
Out of service 0 = Open
BO.2 BO2 State Binary Output 2 State
Present Value 1 = Closed
Out of service 0 = Open
BO.3 BO3 State Binary Output 3 State
Present Value 1 = Closed
Out of service 0 = Open
BO.4 BO4 State Binary Output 4 State
Present Value 1 = Closed
Out of service 0 = Open
BO.5 BO5 State Binary Output 5 State
Present Value 1 = Closed
Out of service 0 = Open
BO.6 BO6 State Binary Output 6 State
Present Value 1 = Closed
Out of service 0 = Open
BO.7 BO7 State Binary Output 7 State
Present Value 1 = Closed
Out of service 0 = Open
BO.8 BO8 State Binary Output 8 State
Present Value 1 = Closed
Out of service 0 = Open
BO.9 BO9 State Binary Output 9 State
Present Value 1 = Closed
Out of service 0 = Open
BO.10 BO10 State Binary Output 10 State
Present Value 1 = Closed
Out of service 0 = Open
BO.11 BO11 State Binary Output 11 State
Present Value 1 = Closed
Out of service 0 = Open
BO.12 BO12 State Binary Output 12 State
Present Value 1 = Closed
Out of service 0 = Open
BO.13 BO13 State* Binary Output 13 State
Present Value 1 = Closed
Out of service 0 = Open
BO.14 BO14 State* Binary Output 14 State
Present Value 1 = Closed
Out of service 0 = Open
BO.15 BO15 State* Binary Output 15 State
Present Value 1 = Closed
Out of service 0 = Open
BO.16 BO16 State* Binary Output 16 State
Present Value 1 = Closed
Select the unit system to use on the 0= Celsius
BV.1 Cfg Temperature Units Present Value
device. 1= Fahrenheit
1= Custom
Out of service 2= Profile 1
MSV.0 Cfg IO Profile Select input/output profile.
Present Value 3= Profile 2
4= Profile 3
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.1 Cfg UI1 Mode Select universal input 1 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1

www.neptronic.com Page | 9
 Remote I/O Communication Module
Specification and Installation Instructions

ID1 Name Description Writable? Range

1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.2 Cfg UI2 Mode Select universal input 2 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.3 Cfg UI3 Mode Select universal input 3 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.4 Cfg UI4 Mode Select universal input 4 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.5 Cfg UI5 Mode Select universal input 5 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.6 Cfg UI6 Mode Select universal input 6 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.7 Cfg UI7 Mode Select universal input 7 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.8 Cfg UI8 Mode Select universal input 8 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.9 Cfg UI9 Mode Select universal input 9 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.10 Cfg UI10 Mode Select universal input 10 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1

www.neptronic.com Page | 10
 Remote I/O Communication Module
Specification and Installation Instructions

ID1 Name Description Writable? Range

1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.11 Cfg UI11 Mode Select universal input 11 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.12 Cfg UI12 Mode Select universal input 12 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.13 Cfg UI13 Mode Select universal input 13 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.14 Cfg UI14 Mode Select universal input 14 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.15 Cfg UI15 Mode Select universal input 15 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.16 Cfg UI16 Mode Select universal input 16 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.17 Cfg UI17 Mode Select universal input 17 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.18 Cfg UI18 Mode Select universal input 18 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.19 Cfg UI19 Mode Select universal input 19 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1

www.neptronic.com Page | 11
 Remote I/O Communication Module
Specification and Installation Instructions

ID1 Name Description Writable? Range

1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.20 Cfg UI20 Mode Select universal input 20 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.21 Cfg UI21 Mode Select universal input 21 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.22 Cfg UI22 Mode Select universal input 22 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.23 Cfg UI23 Mode Select universal input 23 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.24 Cfg UI24 Mode Select universal input 24 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.25 Cfg UI25 Mode Select universal input 25 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.26 Cfg UI26 Mode Select universal input 26 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.27 Cfg UI27 Mode Select universal input 27 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.28 Cfg UI28 Mode Select universal input 28 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1

www.neptronic.com Page | 12
 Remote I/O Communication Module
Specification and Installation Instructions

ID1 Name Description Writable? Range

1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.29 Cfg UI29 Mode Select universal input 29 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
1= 0-10V
2= 4-20mA
3= Dry Contact
Out of service 4= 10K Type3/G/4A1
MSV.30 Cfg UI30 Mode Select universal input 30 mode
Present Value 5= 10K Type2/3A1/NTC(Danfoss)
6= 10K_ NTC Carel
7= 20K Type6A1
8= 30K Type6A1
Selected analog output 1 failsafe Out of service 1= Last State
MSV.31 Cfg AO1 Failsafe Mode
mode Present Value 2= Preset
Selected analog output 2 failsafe Out of service 1= Last State
MSV.32 Cfg AO2 Failsafe Mode
mode Present Value 2= Preset
Selected analog output 3 failsafe Out of service 1= Last State
MSV.33 Cfg AO3 Failsafe Mode
mode Present Value 2= Preset
Selected analog output 4 failsafe Out of service 1= Last State
MSV.34 Cfg AO4 Failsafe Mode
mode Present Value 2= Preset
Selected analog output 5 failsafe Out of service 1= Last State
MSV.35 Cfg AO5 Failsafe Mode*
mode Present Value 2= Preset
Selected analog output 6 failsafe Out of service 1= Last State
MSV.36 Cfg AO6 Failsafe Mode*
mode Present Value 2= Preset
Selected analog output 7 failsafe Out of service 1= Last State
MSV.37 Cfg AO7 Failsafe Mode*
mode Present Value 2= Preset
Selected analog output 8 failsafe Out of service 1= Last State
MSV.38 Cfg AO8 Failsafe Mode*
mode Present Value 2= Preset
1= Last State
Selected binary output 1 failsafe Out of service
MSV.39 Cfg BO1 Failsafe Mode 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 2 failsafe Out of service
MSV.40 Cfg BO2 Failsafe Mode 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 3 failsafe Out of service
MSV.41 Cfg BO3 Failsafe Mode 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 4 failsafe Out of service
MSV.42 Cfg BO4 Failsafe Mode 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 5 failsafe Out of service
MSV.43 Cfg BO5 Failsafe Mode 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 6 failsafe Out of service
MSV.44 Cfg BO6 Failsafe Mode 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 7 failsafe Out of service
MSV.45 Cfg BO7 Failsafe Mode 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 8 failsafe Out of service
MSV.46 Cfg BO8 Failsafe Mode 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 9 failsafe Out of service
MSV.47 Cfg BO9 Failsafe Mode 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 10 failsafe Out of service
MSV.48 Cfg BO10 Failsafe Mode 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 11 failsafe Out of service
MSV.49 Cfg BO11 Failsafe Mode 2= Open
mode Present Value
3= Closed

www.neptronic.com Page | 13
 Remote I/O Communication Module
Specification and Installation Instructions

ID1 Name Description Writable? Range

1= Last State
Selected binary output 12 failsafe Out of service
MSV.50 Cfg BO12 Failsafe Mode 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 13 failsafe Out of service
MSV.51 Cfg BO13 Failsafe Mode** 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 14 failsafe Out of service
MSV.52 Cfg BO14 Failsafe Mode** 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 15 failsafe Out of service
MSV.53 Cfg BO15 Failsafe Mode** 2= Open
mode Present Value
3= Closed
1= Last State
Selected binary output 16 failsafe Out of service
MSV.54 Cfg BO16 Failsafe Mode** 2= Open
mode Present Value
3= Closed

* Only available when JP3 - JP6 jumpers (UO1 - UO4 selector) are set to AO5 - AO8.
** Only available when JP3 - JP6 jumpers (UO1 - UO4 selector) are set to BO13 - BO16.

www.neptronic.com Page | 14
 Remote I/O Communication Module
Specification and Installation Instructions

Modbus Registers
• Register address
o As per protocol base (base 0); for PLC add 1 to protocol base.
o As per holding register (base 40001)
• Functions :
o 03 Read Holding Register
o 06 Write Single Register
o 16 Write Multiple Registers
• Error Codes :
o 02 Illegal Data Address
o 03 Illegal Value
o 06 Slave Device Busy
• W = Writable register, RO = read only.
• No Real number in Modbus register, use scale to calculate real number. Register = Real number * Scale => Real number = Register / Scale. Scale could be 1, 10 or 100
• Attention when writing a register that contains a bit string. If bit is writable (conditional or not), the write will always be accepted. If bit is reserved or not writable, the write will be ignored and
will keep its actual state.
• Use READ-MODIFY-WRITE sequence.

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

Unsigned [1..247]
0 40001 MAC Address W 101
Scale 1 * MAC address is 1 if all DIP switches of DS1 are OFF.
Unsigned
1 40002 Firmware Version 1.00 RO
Scale 100
2 40003 Serial Number (characters 0 & 1) ASCII MSB = char 0, LSB = char 1 RO
3 40004 Serial Number (characters 2 & 3) ASCII MSB = char 2, LSB = char 3 RO
4 40005 Serial Number (characters 4 & 5) ASCII MSB = char 4, LSB = char 5 RO
5 40006 Serial Number (characters 6 & 7) ASCII MSB = char 6, LSB = char 7 RO
6 40007 Serial Number (characters 8 & 9) ASCII MSB = char 8, LSB = char 9 RO
7 40008 Serial Number (characters 10 & 11) ASCII MSB = char 10, LSB = char 11 RO
8 40009 Serial Number (characters 12 & 13) ASCII MSB = char 12, LSB = char 13 RO
9 40010 Serial Number (characters 14 & 15) ASCII MSB = char 14, LSB = char 15 RO
0 = Operational 3 = download-in-progress
10 40011 System Status Unsigned 1 = Operational-read-only 4 = non-operational RO
2 = download-required 5 = backup-in-progress

www.neptronic.com Page | 15
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

11 40012 Universal Input 1 Reading 0

12 40013 Universal Input 2 Reading 0

13 40014 Universal Input 3 Reading 0

14 40015 Universal Input 4 Reading 0

15 40016 Universal Input 5 Reading 0

16 40017 Universal Input 6 Reading 0

17 40018 Universal Input 7 Reading 0

18 40019 Universal Input 8 Reading 0

19 40020 Universal Input 9 Reading 0

20 40021 Universal Input 10 Reading 0

21 40022 Universal Input 11 Reading 0

0-10V: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0-10Volt,
22 40023 Universal Input 12 Reading 4-20mA: Type: Unsigned, Scale:1000, Unit: mA, Range: 0-20 mA 0
10K NTC Carel, 10K Type 2/3A1/NTC(Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
23 40024 Universal Input 13Reading RO 0
Type: Signed, Scale:100, Unit: ºC, Range: -40 - 150 ºC
24 40025 Universal Input 14 Reading Type: Signed, Scale:100, Unit: ºF, Range: -40 - 212 ºF 0
DI: Type: Unsigned, Scale:1, No Unit, Range: 0-1
25 40026 Universal Input 15 Reading 0

26 40027 Universal Input 16 Reading 0

27 40028 Universal Input 17 Reading 0

28 40029 Universal Input 18 Reading 0

29 40030 Universal Input 19 Reading 0

30 40031 Universal Input 20 Reading 0

31 40032 Universal Input 21 Reading 0

32 40033 Universal Input 22 Reading 0

33 40034 Universal Input 23 Reading 0

34 40035 Universal Input 24 Reading 0

35 40036 Universal Input 25 Reading 0

www.neptronic.com Page | 16
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

36 40037 Universal Input 26 Reading 0

0-10V: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0-10Volt,
37 40038 Universal Input 27 Reading 4-20mA: Type: Unsigned, Scale:1000, Unit: mA, Range: 0-20 mA 0
10K NTC Carel, 10K Type 2/3A1/NTC(Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
38 40039 Universal Input 28 Reading RO 0
Type: Signed, Scale:100, Unit: ºC, Range: -40 - 150 ºC
39 40040 Universal Input 29 Reading Type: Signed, Scale:100, Unit: ºF, Range: -40 - 212 ºF 0
DI: Type: Unsigned, Scale:1, No Unit, Range: 0-1
40 40041 Universal Input 30 Reading 0
41 40042 Analog Output 1 Voltage 0V
42 40043 Analog Output 2 Voltage 0V
43 40044 Analog Output 3 Voltage 0V
Unit: Volt (V), Range: 0V to10V, Value x 1000 (e.g. 2V = 2000)
44 40045 Analog Output 4 Voltage Unsigned 0V
W
45 40046 Analog Output 5 Voltage* Scale 1000 * AO5 to AO8 Voltage can only be commanded when JP3 - JP6 jumpers (UO1 - 0V
UO4 selector) are set to AO5 - AO8.
46 40047 Analog Output 6 Voltage* 0V
47 40048 Analog Output 7 Voltage* 0V
48 40049 Analog Output 8 Voltage* 0V

www.neptronic.com Page | 17
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

B0: Binary Output 1 State B8: Binary Output 9 State

0 = Open, 1 = Closed 0 = Open, 1 = Closed

B1: Binary Output 2 State B9: Binary Output 10 State

0 = Open, 1 = Closed 0 = Open, 1 = Closed

B2: Binary Output 3 State B10: Binary Output 11 State

0 = Open, 1 = Closed 0 = Open, 1 = Closed

B3: Binary Output 4 State B11: Binary Output 12 State

0 = Open, 1 = Closed 0 = Open, 1 = Closed

49 40050 Binary Output States** Bit String B4: Binary Output 5 State B12: Binary Output 13 State** W 0
0 = Open, 1 = Closed 0 = Open, 1 = Closed

B5: Binary Output 6 State B13: Binary Output 14 State**

0 = Open, 1 = Closed 0 = Open, 1 = Closed

B6: Binary Output 7 State B14: Binary Output 15 State**

0 = Open, 1 = Closed 0 = Open, 1 = Closed

B7: Binary Output 8 State B15: Binary Output 16 State**

0 = Open, 1 = Closed 0 = Open, 1 = Closed
** B12 to B15 can only be commanded when JP3 - JP6 jumpers (UO1 - UO4
selector) are set to BO13 - BO16.
50 40051 Universal Input 1 Impedance or Linearization (0) N/A
51 40052 Universal Input 1 Impedance or Linearization (1) N/A
52 40053 Universal Input 2 Impedance or Linearization (0) N/A
53 40054 Universal Input 2 Impedance or Linearization (1) 0-10V, 4-20mA: N/A
Type: Unsigned, Scale: Depends on values in Linear Value Scale of corresponding UI
54 40055 Universal Input 3 Impedance or Linearization (0) N/A
Unit: %, Range: Depends on values in Minimum and Maximum Linear Value of the UI
55 40056 Universal Input 3 Impedance or Linearization (1) RO N/A
56 40057 Universal Input 4 Impedance or Linearization (0) Thermistors - 10K NTC Carel, 10K Type 2/3A1/NTC(Danfoss), 20K Type 6AI, 30K Type 6AI, N/A
10K Type 3/G/4A1:
57 40058 Universal Input 4 Impedance or Linearization (1) Type: Unsigned, Scale:1, Unit: Ohms, Range: 0-806800 Ohms N/A
58 40059 Universal Input 5 Impedance or Linearization (0) N/A
59 40060 Universal Input 5 Impedance or Linearization (1) N/A
60 40061 Universal Input 6 Impedance or Linearization (0) N/A

www.neptronic.com Page | 18
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

61 40062 Universal Input 6 Impedance or Linearization (1) N/A

62 40063 Universal Input 7 Impedance or Linearization (0) N/A
63 40064 Universal Input 7 Impedance or Linearization (1) N/A
64 40065 Universal Input 8 Impedance or Linearization (0) N/A
65 40066 Universal Input 8 Impedance or Linearization (1) N/A
66 40067 Universal Input 9 Impedance or Linearization (0) N/A
67 40068 Universal Input 9 Impedance or Linearization (1) N/A
68 40069 Universal Input 10 Impedance or Linearization (0) N/A
69 40070 Universal Input 10 Impedance or Linearization (1) N/A
70 40071 Universal Input 11 Impedance or Linearization (0) N/A
71 40072 Universal Input 11 Impedance or Linearization (1) N/A
72 40073 Universal Input 12 Impedance or Linearization (0) N/A
73 40074 Universal Input 12 Impedance or Linearization (1) 0-10V, 4-20mA: N/A
Type: Unsigned, Scale: Depends on values in Linear Value Scale of corresponding UI
74 40075 Universal Input 13 Impedance or Linearization (0) N/A
Unit: %, Range: Depends on values in Minimum and Maximum Linear Value of the UI
75 40076 Universal Input 13 Impedance or Linearization (1) RO N/A
76 40077 Universal Input 14 Impedance or Linearization (0) Thermistors - 10K NTC Carel, 10K Type 2/3A1/NTC(Danfoss), 20K Type 6AI, 30K Type 6AI, N/A
10K Type 3/G/4A1:
77 40078 Universal Input 14 Impedance or Linearization (1) Type: Unsigned, Scale:1, Unit: Ohms, Range: 0-806800 Ohms N/A
78 40079 Universal Input 15 Impedance or Linearization (0) N/A
79 40080 Universal Input 15 Impedance or Linearization (1) N/A
80 40081 Universal Input 16 Impedance or Linearization (0) N/A
81 40082 Universal Input 16 Impedance or Linearization (1) N/A
82 40083 Universal Input 17 Impedance or Linearization (0) N/A
83 40084 Universal Input 17 Impedance or Linearization (1) N/A
84 40085 Universal Input 18 Impedance or Linearization (0) N/A
85 40086 Universal Input 18 Impedance or Linearization (1) N/A
86 40087 Universal Input 19 Impedance or Linearization (0) N/A
87 40088 Universal Input 19 Impedance or Linearization (1) N/A
88 40089 Universal Input 20 Impedance or Linearization (0) N/A
89 40090 Universal Input 20 Impedance or Linearization (1) N/A

www.neptronic.com Page | 19
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

90 40091 Universal Input 21 Impedance or Linearization (0) N/A

91 40092 Universal Input 21 Impedance or Linearization (1) N/A
92 40093 Universal Input 22 Impedance or Linearization (0) N/A
93 40094 Universal Input 22 Impedance or Linearization (1) N/A
94 40095 Universal Input 23 Impedance or Linearization (0) N/A
95 40096 Universal Input 23 Impedance or Linearization (1) N/A
96 40097 Universal Input 24 Impedance or Linearization (0) N/A
97 40098 Universal Input 24 Impedance or Linearization (1) N/A
0-10V, 4-20mA:
98 40099 Universal Input 25 Impedance or Linearization (0) Type: Unsigned, Scale: Depends on values in Linear Value Scale of corresponding UI N/A
99 40100 Universal Input 25 Impedance or Linearization (1) Unit: %, Range: Depends on values in Minimum and Maximum Linear Value of the UI N/A
RO
100 40101 Universal Input 26 Impedance or Linearization (0) N/A
Thermistors - 10K NTC Carel, 10K Type 2/3A1/NTC(Danfoss), 20K Type 6AI, 30K Type 6AI,
101 40102 Universal Input 26 Impedance or Linearization (1) 10K Type 3/G/4A1: N/A
Type: Unsigned, Scale:1, Unit: Ohms, Range: 0-806800 Ohms
102 40103 Universal Input 27 Impedance or Linearization (0) N/A
103 40104 Universal Input 27 Impedance or Linearization (1) N/A
104 40105 Universal Input 28 Impedance or Linearization (0) N/A
105 40106 Universal Input 28 Impedance or Linearization (1) N/A
106 40107 Universal Input 29 Impedance or Linearization (0) N/A
107 40108 Universal Input 29 Impedance or Linearization (1) N/A
108 40109 Universal Input 30 Impedance or Linearization (0) N/A
109 40110 Universal Input 30 Impedance or Linearization (1) N/A
110 40111 Temperature Units Unsigned 1 = Celsius | 2 = Fahrenheit W 1
1 = Custom 3 = Profile 2
111 40112 Input/Output Profile Unsigned W 2
2 = Profile 1 4 = Profile 3
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
112 40113 Universal Input 1 Mode Unsigned W 6
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC(Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
113 40114 Universal Input 1 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W 0ºC
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
114 40115 Universal Input 1 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A

www.neptronic.com Page | 20
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

115 40116 Universal Input 1 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
116 40117 Universal Input 1 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
117 40118 Universal Input 1 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
118 40119 Universal Input 1 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
119 40120 Universal Input 1 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
120 40121 Universal Input 2 Mode Unsigned W 6
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC(Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
121 40122 Universal Input 2 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W 0ºC
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
122 40123 Universal Input 2 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
123 40124 Universal Input 2 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
124 40125 Universal Input 2 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
125 40126 Universal Input 2 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
126 40127 Universal Input 2 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
127 40128 Universal Input 2 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
128 40129 Universal Input 3 Mode Unsigned W 6
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
129 40130 Universal Input 3 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W 0ºC
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
130 40131 Universal Input 3 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
131 40132 Universal Input 3 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
132 40133 Universal Input 3 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A

www.neptronic.com Page | 21
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V

133 40134 Universal Input 3 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
134 40135 Universal Input 3 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
135 40136 Universal Input 3 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
136 40137 Universal Input 4 Mode Unsigned W 6
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
137 40138 Universal Input 4 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W 0ºC
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
138 40139 Universal Input 4 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
139 40140 Universal Input 4 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
140 40141 Universal Input 4 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
141 40142 Universal Input 4 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
142 40143 Universal Input 4 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
143 40144 Universal Input 5 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
144 40145 Universal Input 5 Mode Unsigned W 6
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
145 40146 Universal Input 5 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W 0ºC
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
146 40147 Universal Input 5 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
147 40148 Universal Input 5 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
148 40149 Universal Input 5 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
149 40150 Universal Input 5 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 22
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V

150 40151 Universal Input 5 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
151 40152 Universal Input 5 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
152 40153 Universal Input 6 Mode Unsigned W 6
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
153 40154 Universal Input 6 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W 0ºC
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
154 40155 Universal Input 6 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
155 40156 Universal Input 6 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
156 40157 Universal Input 6 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
157 40158 Universal Input 6 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
158 40159 Universal Input 6 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
159 40160 Universal Input 6 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
160 40161 Universal Input 7 Mode Unsigned W 6
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
161 40162 Universal Input 7 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W 0ºC
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
162 40163 Universal Input 7 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
163 40164 Universal Input 7 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
164 40165 Universal Input 7 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
165 40166 Universal Input 7 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
166 40167 Universal Input 7 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 23
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V

167 40168 Universal Input 7 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
168 40169 Universal Input 8 Mode Unsigned W 6
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
169 40170 Universal Input 8 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W 0ºC
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
170 40171 Universal Input 8 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
171 40172 Universal Input 8 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
172 40173 Universal Input 8 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
173 40174 Universal Input 8 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
174 40175 Universal Input 8 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
175 40176 Universal Input 8 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
176 40177 Universal Input 9 Mode Unsigned W 6
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
177 40178 Universal Input 9 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W 0ºC
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
178 40179 Universal Input 9 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
179 40180 Universal Input 9 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
180 40181 Universal Input 9 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
181 40182 Universal Input 9 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
182 40183 Universal Input 9 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
183 40184 Universal Input 9 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 24
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)

2= 4-20mA 6= 10K NTC Carel
184 40185 Universal Input 10 Mode Unsigned W 3
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
185 40186 Universal Input 10 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
186 40187 Universal Input 10 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
187 40188 Universal Input 10 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
188 40189 Universal Input 10 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
189 40190 Universal Input 10 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
190 40191 Universal Input 10 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
191 40192 Universal Input 10 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
192 40193 Universal Input 11 Mode Unsigned W 3
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
193 40194 Universal Input 11 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
194 40195 Universal Input 11 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
195 40196 Universal Input 11 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
196 40197 Universal Input 11 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
197 40198 Universal Input 11 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
198 40199 Universal Input 11 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
199 40200 Universal Input 11 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 25
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)

2= 4-20mA 6= 10K NTC Carel
200 40201 Universal Input 12 Mode Unsigned W 3
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
201 40202 Universal Input 12 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
202 40203 Universal Input 12 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
203 40204 Universal Input 12 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
204 40205 Universal Input 12 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
205 40206 Universal Input 12 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
206 40207 Universal Input 12 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
207 40208 Universal Input 12 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
208 40209 Universal Input 13 Mode Unsigned W 3
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
209 40210 Universal Input 13 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
210 40211 Universal Input 13 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
211 40212 Universal Input 13 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
212 40213 Universal Input 13 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
213 40214 Universal Input 13 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
214 40215 Universal Input 13 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
215 40216 Universal Input 13 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 26
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)

2= 4-20mA 6= 10K NTC Carel
216 40217 Universal Input 14 Mode Unsigned W 3
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
217 40218 Universal Input 14 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
218 40219 Universal Input 14 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
219 40220 Universal Input 14 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
220 40221 Universal Input 14 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
221 40222 Universal Input 14 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
222 40223 Universal Input 14 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
223 40224 Universal Input 14 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V
2= 4-20mA
224 40225 Universal Input 15 Mode Unsigned N/A W 3
3= Dry Contact
4= 10K Type3/G/4A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
225 40226 Universal Input 15 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
226 40227 Universal Input 15 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
227 40228 Universal Input 15 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
228 40229 Universal Input 15 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
229 40230 Universal Input 15 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
230 40231 Universal Input 15 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
231 40232 Universal Input 15 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 27
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)

2= 4-20mA 6= 10K NTC Carel
232 40233 Universal Input 16 Mode Unsigned W 3
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
233 40234 Universal Input 16 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
234 40235 Universal Input 16 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
235 40236 Universal Input 16 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
236 40237 Universal Input 16 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
237 40238 Universal Input 16 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
238 40239 Universal Input 16 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
239 40240 Universal Input 16 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
240 40241 Universal Input 17 Mode Unsigned W 3
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
241 40242 Universal Input 17 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
242 40243 Universal Input 17 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W N/A
243 40244 Universal Input 17 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
244 40245 Universal Input 17 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W N/A
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
245 40246 Universal Input 17 Minimum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
246 40247 Universal Input 17 Maximum Linear Value W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
247 40248 Universal Input 17 Linear Value Bias W N/A
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 28
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)

2= 4-20mA 6= 10K NTC Carel
248 40249 Universal Input 18 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
249 40250 Universal Input 18 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
250 40251 Universal Input 18 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
251 40252 Universal Input 18 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
252 40253 Universal Input 18 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
253 40254 Universal Input 18 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
254 40255 Universal Input 18 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
255 40256 Universal Input 18 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
256 40257 Universal Input 19 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
257 40258 Universal Input 19 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
258 40259 Universal Input 19 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
259 40260 Universal Input 19 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
260 40261 Universal Input 19 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
261 40262 Universal Input 19 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
262 40263 Universal Input 19 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
263 40264 Universal Input 19 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 29
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)

2= 4-20mA 6= 10K NTC Carel
264 40265 Universal Input 20 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
265 40266 Universal Input 20 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
266 40267 Universal Input 20 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
267 40268 Universal Input 20 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
268 40269 Universal Input 20 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
269 40270 Universal Input 20 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
270 40271 Universal Input 20 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
271 40272 Universal Input 20 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
272 40273 Universal Input 21 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
273 40274 Universal Input 21 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
274 40275 Universal Input 21 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
275 40276 Universal Input 21 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
276 40277 Universal Input 21 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
277 40278 Universal Input 21 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
278 40279 Universal Input 21 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
279 40280 Universal Input 21 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 30
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)

2= 4-20mA 6= 10K NTC Carel
280 40281 Universal Input 22 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
281 40282 Universal Input 22 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
282 40283 Universal Input 22 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
283 40284 Universal Input 22 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
284 40285 Universal Input 22 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
285 40286 Universal Input 22 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
286 40287 Universal Input 22 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
287 40288 Universal Input 22 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
288 40289 Universal Input 23 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
289 40290 Universal Input 23 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
290 40291 Universal Input 23 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
291 40292 Universal Input 23 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
292 40293 Universal Input 23 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
293 40294 Universal Input 23 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
294 40295 Universal Input 23 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
295 40296 Universal Input 23 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 31
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)

2= 4-20mA 6= 10K NTC Carel
296 40297 Universal Input 24 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
297 40298 Universal Input 24 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
298 40299 Universal Input 24 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
299 40300 Universal Input 24 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
300 40301 Universal Input 24 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
301 40302 Universal Input 24 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
302 40303 Universal Input 24 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
303 40304 Universal Input 24 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
304 40305 Universal Input 25 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
305 40306 Universal Input 25 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
306 40307 Universal Input 25 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
307 40308 Universal Input 25 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
308 40309 Universal Input 25 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
309 40310 Universal Input 25 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
310 40311 Universal Input 25 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
311 40312 Universal Input 25 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 32
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)

2= 4-20mA 6= 10K NTC Carel
312 40313 Universal Input 26 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
313 40314 Universal Input 26 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
314 40315 Universal Input 26 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
315 40316 Universal Input 26 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
316 40317 Universal Input 26 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
317 40318 Universal Input 26 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
318 40319 Universal Input 26 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
319 40320 Universal Input 26 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
320 40321 Universal Input 27 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
321 40322 Universal Input 27 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
322 40323 Universal Input 27 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
323 40324 Universal Input 27 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
324 40325 Universal Input 27 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
325 40326 Universal Input 27 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
326 40327 Universal Input 27 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
327 40328 Universal Input 27 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 33
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)

2= 4-20mA 6= 10K NTC Carel
328 40329 Universal Input 28 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
329 40330 Universal Input 28 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
330 40331 Universal Input 28 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
331 40332 Universal Input 28 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
332 40333 Universal Input 28 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
333 40334 Universal Input 28 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
334 40335 Universal Input 28 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
335 40336 Universal Input 28 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)
2= 4-20mA 6= 10K NTC Carel
336 40337 Universal Input 29 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
337 40338 Universal Input 29 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
338 40339 Universal Input 29 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
339 40340 Universal Input 29 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
340 40341 Universal Input 29 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
341 40342 Universal Input 29 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
342 40343 Universal Input 29 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
343 40344 Universal Input 29 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA

www.neptronic.com Page | 34
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

1= 0-10V 5= 10K Type2/3A1/NTC(Danfoss)

2= 4-20mA 6= 10K NTC Carel
344 40345 Universal Input 30 Mode Unsigned W 2
3= Dry Contact 7= 20K Type6A1
4= 10K Type3/G/4A1 8= 30K Type6A1
10K NTC Carel, 10K Type 2/3A1/NTC (Danfoss), 20K Type 6AI, 30K Type 6AI, 10K Type 3/G/4A1:
345 40346 Universal Input 30 Reading Bias Type: Signed, Scale:100, Unit: ºC, Range: -327.68 - 327.67ºC W N/A
Type: Signed, Scale:100, Unit: ºF, Range: -557.82 - 621.08 ºF
346 40347 Universal Input 30 Linear Value Scale 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: No Unit, Range: 0.001, 0.01, 0.1, 1 or 10 W 1
347 40348 Universal Input 30 Minimum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 0V
348 40349 Universal Input 30 Maximum Voltage 0-10V, 4-20mA: Type: Unsigned, Scale:1000, Unit: Volt, Range: 0.00 - 65.535V W 20V
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
349 40350 Universal Input 30 Minimum Linear Value W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
350 40351 Universal Input 30 Maximum Linear Value W 100mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
0-10V: Type: Signed, Scale: 1, Unit: Volt, Range: -32768 - 32767V
351 40352 Universal Input 30 Linear Value Bias W 0mA
4-20mA: Type: Signed, Scale: 1, Unit: mA, Range: -32768 - 32767mA
Unsigned
352 40353 Failsafe Timeout Unit: Seconds (sec), Range: 0 sec to 65535 sec, Value x 1 (e.g. 2 sec = 2) W 60
Scale 1
353 40354 Analog Output 1 Failsafe Mode Unsigned 1 = Last State | 2 = Preset W 2
Unsigned
354 40355 Analog Output 1 Preset Unit: Volt (V), Range: 0V to 10V, Value x 1000 (e.g. 2V = 2000) W 0V
Scale 1000
355 40356 Analog Output 2 Failsafe Mode Unsigned 1 = Last State | 2 = Preset W 2
Unsigned
356 40357 Analog Output 2 Preset Unit: Volt (V), Range: 0V to 10V, Value x 1000 (e.g. 2V = 2000) W 0V
Scale 1000
357 40358 Analog Output 3 Failsafe Mode Unsigned 1 = Last State | 2 = Preset W 2
Unsigned
358 40359 Analog Output 3 Preset Unit: Volt (V), Range: 0V to 10V, Value x 1000 (e.g. 2V = 2000) W 0V
Scale 1000
359 40360 Analog Output 4 Failsafe Mode Unsigned 1 = Last State | 2 = Preset W 2
Unsigned
360 40361 Analog Output 4 Preset Unit: Volt (V), Range: 0V to 10V, Value x 1000 (e.g. 2V = 2000) W 0V
Scale 1000
361 40362 Analog Output 5 Failsafe Mode*** Unsigned 1 = Last State | 2 = Preset W 2
Unsigned
362 40363 Analog Output 5 Preset*** Unit: Volt (V), Range: 0V to 10V, Value x 1000 (e.g. 2V = 2000) W 0V
Scale 1000
363 40364 Analog Output 6 Failsafe Mode*** Unsigned 1 = Last State | 2 = Preset W 2
Unsigned
364 40365 Analog Output 6 Preset*** Unit: Volt (V), Range: 0V to 10V, Value x 1000 (e.g. 2V = 2000) W 0V
Scale 1000

www.neptronic.com Page | 35
 Remote I/O Communication Module
Specification and Installation Instructions

Protocol Holding
Base Register
Description Data Type Units/Values Writable Default Value

365 40366 Analog Output 7 Failsafe Mode*** Unsigned 1 = Last State | 2 = Preset W 2
Unsigned
366 40367 Analog Output 7 Preset*** Unit: Volt (V), Range: 0V to 10V, Value x 1000 (e.g. 2V = 2000) W 0V
Scale 1000
367 40368 Analog Output 8 Failsafe Mode*** Unsigned 1 = Last State | 2 = Preset W 2
Unsigned
368 40369 Analog Output 8 Preset*** Unit: Volt (V), Range: 0V to 10V, Value x 1000 (e.g. 2V = 2000) W 0V
Scale 1000
369 40370 Binary Output 1 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
370 40371 Binary Output 2 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
371 40372 Binary Output 3 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
372 40373 Binary Output 4 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
373 40374 Binary Output 5 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
374 40375 Binary Output 6 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
375 40376 Binary Output 7 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
376 40377 Binary Output 8 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
377 40378 Binary Output 9 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
378 40379 Binary Output 10 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
379 40380 Binary Output 11 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
380 40381 Binary Output 12 Failsafe Mode Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
381 40382 Binary Output 13 Failsafe Mode**** Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
382 40383 Binary Output 14 Failsafe Mode**** Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
383 40384 Binary Output 15 Failsafe Mode**** Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2
384 40385 Binary Output 16 Failsafe Mode**** Unsigned 1 = Last State | 2 = Open | 3 = Closed W 2

*** Only available when JP3 - JP6 jumpers (UO1 - UO4 selector) are set to AO5 - AO8.
**** Only available when JP3 - JP6 jumpers (UO1 - UO4 selector) are set to BO13 - BO16.

Recycling at end of life: please return this product to your Neptronic local distributor for recycling. If you need to find the nearest Neptronic authorized distributor, please consult www.neptronic.com.

www.neptronic.com Page | 36