Technical Data Sheet
LOCTITE® SI 587™
Known as LOCTITE® 587
August-2014
PRODUCT DESCRIPTION TYPICAL PROPERTIES OF UNCURED MATERIAL
LOCTITE® SI 587™ provides the following product Specific Gravity @ 25 °C 1.28 to 1.33LMS
characteristics: Extrusion Rate, g/min:
Technology Silicone Pressure 0.62 MPa, time 15 seconds, temperature 25 °C:
Chemical Type Oxime silicone Semco Cartridge 250 to 600LMS
Appearance (uncured) Metallic blue pasteLMS Flow, ISO 7390, mm:
After 2 minutes @ 25 °C ≤12.7LMS
Components One component -
requires no mixing Flash Point - See SDS
Thixotropic Reduced migration
of liquid product after
application to substrate TYPICAL CURING PERFORMANCE
Cure Room temperature vulcanizing (RTV)
Surface Cure
Application Gasketing or Sealing
Tack Free Time, minutes:
Flexibility Enhances load bearing & shock Cured @ 25 °C / 50±5 % RH 10 to 50LMS
absorbing characteristics of the bond
area.
Specific Application Gasket replacement or Gasket TYPICAL PROPERTIES OF CURED MATERIAL
dressing Cured for 7 days @ 25 °C / 50±5 % RH
Physical Properties:
Specific Benefit Excellent resistance to automotive
Tensile Strength, ISO 37 N/mm² ≥1.6LMS
engine oils and Adheres to a wide (psi) (≥232)
range of substrates Elongation, ISO 37, % ≥350LMS
Shore Hardness, ISO 868, Durometer A 26 to 40LMS
LOCTITE® SI 587™ is used for gasketing and sealing
GENERAL INFORMATION
applications for both plant maintenance and small, medium,
This product is not recommended for use in pure oxygen
and large-sized OEM. As a formed-in-place gasket/sealant,
and/or oxygen rich systems and should not be selected as
LOCTITE® SI 587™ has been designed to give outstanding a sealant for chlorine or other strong oxidizing materials.
performance in typical automotive gasketing applications
including valve covers, rocker covers, oil pans, water pumps, For safe handling information on this product, consult the
Safety Data Sheet (SDS).
end seals, intake manifolds, and rear axle housings. Excellent
adhesive for bonding and repairing fabricated silicone gaskets.
This product is typically used in applications up to 260 °C. Directions for use:
1. For best performance bond surfaces should be clean and
free from grease.
NSF International
2. Full performance properties will develop over 72 hours.
Registered to NSF Category P1 for use as a sealant where
there is no possibilty of food contact in and around food 3. Moisture curing begins immediately after the product is
processing areas. Note: This is a regional approval. Please exposed to the atmosphere, therefore parts to be
contact your local Technical Service Center for more assembled should be mated within a few minutes after the
information and clarification. product is dispensed.
4. Excess material can be easily wiped away with non-polar
UL Classification solvents.
Classified by Underwriters Laboratories Inc.® E257711 - 5. Excess cured material can be removed with a knife or
Plastics & Components. Please visit the UL website for single edge razor blade.
additional information. Note: This is a regional approval.
Please contact your local Technical Service Center for more NOTE: Do not use LOCTITE® SI 587™ for gasketing
information and clarification carburetors or fuel control devices where it will be in
constant contact with hydrocarbon fuels. Material will
develop excessive swell and loss of mechanical
properties.
TDS LOCTITE® SI 587™, August-2014
and conditions in respect of which you use them, as well as the intended
® applications and results. We strongly recommend that you carry out your own
Do not use LOCTITE SI 587™ as a sealant for prior trials to confirm such suitability of our product.
concentrated solutions of acetic, hydrochloric, nitric or Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
sulfuric acids. except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
Loctite Material SpecificationLMS
LMS dated June-8, 2004. Test reports for each batch are In case products are delivered by Henkel Corporation, Resin Technology
available for the indicated properties. LMS test reports include Group, Inc., or Henkel Canada Corporation, the following disclaimer is
applicable:
selected QC test parameters considered appropriate to The data contained herein are furnished for information only and are believed to
specifications for customer use. Additionally, comprehensive be reliable. We cannot assume responsibility for the results obtained by others
controls are in place to assure product quality and over whose methods we have no control. It is the user's responsibility to
consistency. Special customer specification requirements may determine suitability for the user's purpose of any production methods mentioned
herein and to adopt such precautions as may be advisable for the protection of
be coordinated through Henkel Quality. property and of persons against any hazards that may be involved in the handling
and use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including warranties of
Storage merchantability or fitness for a particular purpose, arising from sale or use
Store product in the unopened container in a dry location. of Henkel Corporation’s products. Henkel Corporation specifically
Storage information may be indicated on the product container disclaims any liability for consequential or incidental damages of any kind,
labeling. including lost profits. The discussion herein of various processes or
compositions is not to be interpreted as representation that they are free from
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or domination of patents owned by others or as a license under any Henkel
greater than 28 °C can adversely affect product properties. Corporation patents that may cover such processes or compositions. We
Material removed from containers may be contaminated during recommend that each prospective user test his proposed application before
repetitive use, using this data as a guide. This product may be covered by one or
use. Do not return product to the original container. Henkel more United States or foreign patents or patent applications.
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than Trademark usage
those previously indicated. If additional information is required, Except as otherwise noted, all trademarks in this document are trademarks of
please contact your local Technical Service Center or Henkel Corporation in the U.S. and elsewhere. ® denotes a trademark
Customer Service Representative. registered in the U.S. Patent and Trademark Office.
Conversions
(°C x 1.8) + 32 = °F Reference 1.4
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Belgium NV, Henkel Electronic
Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the following
disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
Henkel Americas Henkel Europe Henkel Asia Pacific
+860.571.5100 +49.89.320800.1800 +86.21.2891.8859
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
