jn0-648_5-1

100% Valid and Newest Version JN0-648 Questions & Answers shared by Certleader
https://www.certleader.com/JN0-648-dumps.html (89 Q&As)
JN0-648 Dumps
Enterprise Routing and Switching Professional (JNCIP-ENT)
https://www.certleader.com/JN0-648-dumps.html
The Leader of IT Certification visit - https://www.certleader.com

NEW QUESTION 1
Exhibit.
You are implementing CoS for a custom application that is labeling its packets with DSCP code-point 101111. You have applied the configuration shown in the
exhibit, but not that while some custom application traffic ingressin on ge-0/0/1 transits the SRX Series device successfully, packets ingressing all other ge-*
interfaces are being dropped.
Which action should you take to solve this problem?
A. Configure a scheduler and scheduler map for expedited-forwarding and apply to all interfaces.
B. Modify the BA classifier to assign code point 101111 to loss priority low.
C. Remove the BA classifier from all ge-interfaces.
D. Apply the rate-limit-ef policer to all ge-interfaces.
Answer: D
NEW QUESTION 2
Which three types of ports are used for Junos Fusion Enterprise? (Choose three. )
A. extended port
B. authenticated port
C. cascade port
D. uplink port

E. designated port
Answer: ACD
NEW QUESTION 3
Exhibit.
Referring to the configuration shown in the exhibit, how many of the routes received from 10.0.0.2 will be active in the routing table?
A. 2
B. 8
C. 3
D. 5
Answer: C
NEW QUESTION 4
Click the Exhibit button.
You are adding VNI 101 to your EVPN-VXLAN network, but traffic is not being sent or received. Referring to the exhibit, which configuration statement will solve
the problem?
A. set routing-instances EVPN1 instance-type evpn

B. set routing-instances EVPN1 vxlan encapsulate-inner-vlan
C. set routing-instances EVPN1 bridge-domains BD-101 vxlan vni 101
D. set routing-instances EVPN1 vrf-table-label
Answer: A

NEW QUESTION 5
What are three well-known mandatory BGP attributes? (Choose three.)
A. AS-path
B. community
C. origin
D. MED
E. next-hop
Answer: ACE
NEW QUESTION 6
You are deploying IP phones in your Layer 2 network and are asked to ensure that the switch sends VLAN and CoS information to the IP phones automatically.
In this scenario, which protocol should be used?
A. PoE
B. PoE+
C. LLDP
D. LLDP_MED
Answer: D
NEW QUESTION 7
You have configured class mode power management on an EX4300 to provide PoE power to telephone and security camera equipment. You want to ensure that
security camera power takes priority over telephone power.
Which two actions would solve this problem? (Choose two.)
A. Connect the security cameras to the lowest port numbers on the switch.
B. Set the power priority to high on ports connected to security cameras.
C. Set the maximum power settings on ports connected to security cameras.
D. Set the power priority to low on ports connected to security cameras.
Answer: AB
NEW QUESTION 8
Referring to the exhibit, the source is currently sending multicast traffic using group 224.1.1.1, which is being received by R1. R2 is not receiving PIM register
messages.
What would be the cause of this problem?
A. Tunnel services have not been enabled on R1.

B. All routers have not been configured with the same Auto-RP discovery group.
C. R5 has not received an IGMP report of 224.1.1.1.
D. A(*,G) tree has not been built yet.
Answer: C

NEW QUESTION 9
Your network is configured for EVPN load balancing on three different access switches During an outage, you notice that not all interfaces are receiving traffic as
expected
Which two requirements would you validate to identify this problem? (Choose two )
A. Validate that the same esi value is only configured on one interface per switch
B. Validate that the same esi value is configured on multiple interfaces on all switches.
C. Validate that all-active is configured for only interface per switch
D. Validate that the all-active flag configured for multiple interfaces on each switch
Answer: BD
NEW QUESTION 10
Which two statements are true about IS-IS levels? (Choose two.)
A. Level 2 systems do not advertise Level 2 routes into a Level area by default.
B. Level 2 systems must use the loopback address as a part of the ISO network address.
C. Level 1 system only from adjacencies with other systems that have different area IDs.
D. Level 1 systems use a default route to reach AS external routes located in other areas.
Answer: AD
NEW QUESTION 10
Referring to the exhibit, how is R5 able to learn the networks that exist within the NSSA?
A. R5 learns those networks from Type 3 LSAs advertised by R2.

B. R5 learns those networks from Type 3 LSAs advertised by R3.
C. R5 does not learn those networks and uses a default route advertised by R3 instead.
D. R5 does not learn those networks but uses a default route advertised by R2 instead.
Answer: D
NEW QUESTION 13
Which two statements are true regarding bidirectional PIM? (Choose two )
A. It eliminates the need for an RP.

B. Devices only store group specific entries.
C. It uses multicast tunneling to forward traffic
D. Forwarding paths can be suboptimal
Answer: BD
NEW QUESTION 18
You are implementing 802.1x access control in your network of EX Series switches. You have some older client devices connecting to your network which do not
support 802.1x.
Which statement is true regarding the older devices?
A. By default, the supplicant will send EAP messages and keep the port in an unauthorized state.
B. By default, the authenticator will send EAP messages and keep the port in an unauthorized state.
C. By default, the supplicant will send EAP messages until it reaches a predefined limit, after which it begins to forward traffic.By default, the authenticator will send
EAP messages until it reaches a predefined, after which it begins to forward traffic.
Answer: C

NEW QUESTION 22
You are designing a multicast topology to support IPv4 IPTV broadcasts in your organization. The design should support multiple multicast senders with
overlapping group addresses while preventing interference between them. Client devices currently do not support IGMPv3.
Which approach would fulfill these requirements?
A. Implement PIM-SM and SSM with SSM maps to support IGMPv2 clients
B. Implement bidirectional PIM
C. Assign group addresses in the 224/4 range and implement PIM-DM
D. Implement MLD
Answer: C
NEW QUESTION 25
In IS-IS advertising POUs with the overload bit has which effect?
A. The local device will no longer be used for transit traffic

B. The local device's POUs are marked with a metric of 65535
C. The ISIS adjacencies become passive
D. The IS-IS adjacencies enter the "new" state
Answer: A
NEW QUESTION 26
Which two statements about OSPF routing policies are correct? (Choose two.)
A. By default, OSPF export policies reject network-summary LSAs.

B. By default, OSPF export policies accept network-summary LSAs.
C. By default, OSPF import policies accept network-summary LSAs.
D. By default, OSPF import policies reject network-summary LSAs.
Answer: AC
NEW QUESTION 31
Which protocol is used for port-level access control and authentication?
A. MD5
B. IPsec
C. 802.1x
D. AES
Answer: C
NEW QUESTION 35
You are currently using VLAN IDs 2 through 300 within your Layer 2 domain and you need to configure VSTP to prevent loops You must ensure that all VL ANs
are loop free.
In this scenario, which statement is correct?
A. You must enable RSTP to account for all VLANs.

B. You must ensure that the VLANs are balanced between two different root bridges.
C. You must ensure that the bridge priority is set to the lowest value on all switches in the Layer 2 domain.
D. You must enable all VLANs, 2 through 300, under the VSTP configuration
Answer: D
NEW QUESTION 39
You receive the same 100.200.0/16 route from all four ISPs to which you are connected. Referring to the exhibit, which ISP's route will be selected as active?
A. ISP-A
B. ISP-B
C. ISP-C
D. ISP-D
Answer: A
NEW QUESTION 40


There is a functioning OSPFv3 neighborship between Router-1 and Router-2 over the ge-0/0/1 link. However, the 172.100.100.0/24 and 172.101.101.100/24
routes are not being shared through OSPFv3.
Referring to the configuration shown in the exhibit, which two actions must you take to solve the problem? (Choose two.)
A. Add interface ge-0/0/1 under the IPv4 unicast realm for both routers.
B. Add the IPv6 family protocol under ge-0/0/2 for both routers.
C. Add the lo0 interface under OSPFv3 for both routers.
D. Add interface ge-0/0/2 under OSPFv3 for both routers.
Answer: AB
NEW QUESTION 44

You recently implemented the configuration shown in the exhibit. After committing these changes, the community devices connected to AS-1 are not able to
communicate with the appropriate community devices connected to AS-2.
What must be done to allow these community devices to communicate?
A. You must configure to allow the ge-0/0/1 interface on AS-1 as the inter-switch.
B. You must configure the ge-0/0/10 interface on AS-1 as the inter-switch link.
C. You must configure the ge-0/0/1 interface on both switches the inter-switch links.
D. You must configure an isolation VLAN ID under the vlan-pri vlan on the AS-2 switch.
E. You must configure an isolation VLAN ID under the vlan-pri VLAN on both switches.
Answer: C
NEW QUESTION 45
You have configured CoS on a Junos device. A packet is classified as best effort by a behavior aggregate (BA) classifier, and as expedited forwarding by a
multifield (MF) classifier.
Which statement is true in this scenario?
A. The packet will be placed in a queue associated with the BA classifier.

B. The packet will be placed into the queue which is least congested.

C. The packet will be placed into the queue that has the most bandwidth assigned to it.
D. The packet will be placed in a queue associated with the MF classifier.
Answer: A
NEW QUESTION 48
What are two supported PoE management modes? (Choose two.)
A. mixed
B. standalone
C. class
D. static
Answer: CD
NEW QUESTION 50
You are asked to deploy 802.1X on your EX Series switches. You need to ensure authenticated devices continue to have access to the network even if the
authentication server fails.
Which action meets this configuration objective?
A. Configure the server fail fallback with a value of sustain.

B. Set the reauthentication interval to a value of 0.
C. Configure the static MAC bypass for the authentication server.
D. Set the reauthentication interval to a value of disable.
Answer: A
NEW QUESTION 51
Exhibit.
YourNet is learning the 210.210.40.0/24 route from Provider A and Provider B YourNet would like to forward traffic destined to the 210.210.40.0/24 networking
using Provider B.
Referring to the exhibit, how would you accomplish this task?
A. Add the well-known no-export community to the routes learned through R2.
B. Apply an export policy to R1's IBGP peers to set a higher local preference.
C. Add the well-known no-export community to the routes learned through R1.
D. Apply an export policy to R2's IBGP peers to set a Their local preference.
Answer: D
NEW QUESTION 56
Exhibit.

Referring to the log shown in the exhibit, what is the problem with the OSPF adjacency establishment?
A. The interface IP addresses on the subnet are duplicates.

B. There is an MDS authentication mismatch.
C. The referenced IP address does not exist on the network segment.
D. The OSPF database description packet is malformed.
Answer: A
NEW QUESTION 59
Which two statements are correct about a functional ESI LAG interface? (Choose two )
A. The LACP system ID must be different

B. The LACP system ID must be the same
C. The ESI values must be different
Answer: BC
NEW QUESTION 61
When redistributing IGP routes into BGP. what information .s used by default on Junos platforms to determine
the BGP route's MED attribute value?
A. routing information base

B. the IGP route preference
C. the IGP Metric
D. route protocol source
Answer: C
NEW QUESTION 63
......

Thank You for Trying Our Product
* 100% Pass or Money Back

All our products come with a 90-day Money Back Guarantee.
* One year free update
You can enjoy free update one year. 24x7 online support.
* Trusted by Millions
We currently serve more than 30,000,000 customers.
* Shop Securely
All transactions are protected by VeriSign!
100% Pass Your JN0-648 Exam with Our Prep Materials Via below:
https://www.certleader.com/JN0-648-dumps.html

Powered by TCPDF (www.tcpdf.org)

jn0-648_5-1

Uploaded by

Copyright:

Available Formats

jn0-648_5-1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

jn0-648_5-1

Uploaded by

Copyright:

Available Formats

100% Valid and Newest Version JN0-648 Questions & Answers shared by Certleader

https://www.certleader.com/JN0-648-dumps.html (89 Q&As)

Enterprise Routing and Switching Professional (JNCIP-ENT)

The Leader of IT Certification visit - https://www.certleader.com

The Leader of IT Certification visit - https://www.certleader.com

A. set routing-instances EVPN1 instance-type evpn

The Leader of IT Certification visit - https://www.certleader.com

A. Tunnel services have not been enabled on R1.

The Leader of IT Certification visit - https://www.certleader.com

A. R5 learns those networks from Type 3 LSAs advertised by R2.

A. It eliminates the need for an RP.

The Leader of IT Certification visit - https://www.certleader.com

A. The local device will no longer be used for transit traffic

A. By default, OSPF export policies reject network-summary LSAs.

A. You must enable RSTP to account for all VLANs.

The Leader of IT Certification visit - https://www.certleader.com

The Leader of IT Certification visit - https://www.certleader.com

The Leader of IT Certification visit - https://www.certleader.com

A. The packet will be placed in a queue associated with the BA classifier.

The Leader of IT Certification visit - https://www.certleader.com

A. Configure the server fail fallback with a value of sustain.

The Leader of IT Certification visit - https://www.certleader.com

A. The interface IP addresses on the subnet are duplicates.

A. The LACP system ID must be different

A. routing information base

The Leader of IT Certification visit - https://www.certleader.com

Thank You for Trying Our Product

* 100% Pass or Money Back

The Leader of IT Certification visit - https://www.certleader.com

You might also like