Scribd Logo
Upload

Welcome to Scribd!

  • 4 views

    Jenish Navik _1727590563

    Uploaded by

    Jêmš Navik

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd

    Jenish Navik _1727590563

    Uploaded by

    Jêmš Navik
    4 views8 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    4 views8 pages

    Jenish Navik _1727590563

    Uploaded by

    Jêmš Navik

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 8

    Instrument Technician

    JENISHNAVIK
     +917359297275
    [email protected]
    Address: At New Street, Bhimpore, Post -Dumas
    Dist: Surat (Pin – 395007)
    Gujarat State, Nationality: Indian

    Objective:

    Seeking an innovative career in professionally managed organization, which provides responsibilities that will
    effectively utilize and developed my abilities and skills in the performance of any work

    Educational Qualifications:
     DIPLOMA, INSTRUMENTATION AND CONTROL ENGINEERING - Passed Year JULY-2009 with (A Grade) from
    INSTITUTE OF BUSINESS MANAGEMENT AND ENGINEERING,
    EIILM University Sikkim, Surat, Gujarat, India
     GUJARAT SECONDARY EDUCATION Passed S.S.C. Examination in March – 2006, Gujarat Board – GSEB

    Training Programmer:
    APAVA TRAINING
    Preparation for the Authorization of Electricians Operating in LOW and/or HIGH Voltage Doha
    Qatar
    Validity: 13 September 2022

    PERFORMER TRAINING
    Passed the ADNOC offshore PTW training and duty authorized as a PERFORMER UZ750 Al Ghallan Island, Abu
    Dhabi Validity: December 2020

    OFFSHORE TRAINING
     HSE Induction & H2S from ADNOC LNG / DAS Island Offshore Abu
    Dhabi
     HSE Induction & H2S from TOTAL TEPQ Offshore Doha
    Qatar
     HSE Induction & H2S from ADNOC /ZADCO (UZ750) Offshore Abu
    Dhabi
     HSE Induction & H2S from N-KOM (Offshore) Doha
    Qatar
     HSE Induction & Sea Survival from OXY (Offshore) Doha
    Qatar
    Fire & Safety Training, Life Boat safely and Helicopter Underwater Escape Training at QATAR
    ONSHORE TRAINING
     HSE Induction (PTW, Work at Height, CSW, H2S Environment) From Qatar petroleum & QAFCO Doha
    Qatar
     HSE induction from JGC (Japan Gas Corporation ) Doha
    Qatar
     HSE Induction & H2S from LNG Train 3 Oman
    Offshore Certificate:

    ETSDC- EMIRATES TECHNICAL & SAFETY DEVELOPMENT CENTRE

     ZADCO Offshore Safety Valid: 16 October –


    2022
     H2s Training Valid: 16 October –
    2020
     Travel Safely By Boat Valid: 16 October –
    2022

    VENTURE GULF TRAINING CENTRE (OPITO)

     T – H.U.E.T OPITO Valid: 09 September


    2023
     H2s / BA (QP Approved) Valid: 09 September
    2020

    Experience:
    I consider myself to be dedicated, experiences 10+ years of experience working for Commissioning,
    Maintenance operation, Projects, Shutdowns in Oil & Gas Sector, LNG, Power Plants, Fertilizers,
    Petrochemicals and other process industries (Offshore/Onshore) in Abroad

    Organizational Experience:

    1) ADNOC - LNG Offshore ( DAS Island - IGD Train 1,2,3) at Abu Dhabi

    Designation : Instrument Technician


    Duration : 2 - November - 2019 to 01 - January - 2020
    Clint : EMC - EURO MECHANICAL (Batch No: ITV 094)
    Optima No : 882147

    2) TOTAL TEPQ Offshore ( DP1 – PP1) at Doha Qatar

    Designation : Instrument Technician


    Duration : 1 - September - 2019 to 3 - October - 2019
    Clint : SPIE

    3) ADNOC - ZADCO Offshore (EPC Project- UZ 750) at Abu Dhabi

    Designation : Instrument Commissioning Technician (Rotation: 90/15)


    Duration : 14 - October - 2018 to 20 - August - 2019 (11 Month)
    Clint : Petrofac Engineering (Batch No: 617942)
    Optima No : 640912

    4) Umm Al Houl power (Samsung C&T) (2500MW) at Doha Qatar

    Designation : Instrument Commissioning Technician


    Duration : 25 - October 2017 to 16 - May 2018 (9 Month)
    Clint : QCON - Qatar Engineering & Construction Co.

    5) QAFCO (Qatar Fertilizer Company) Ammonia 4 at Doha Qatar

    Designation : Instrument Technician


    Duration : 23 - October 2016 to 26 - April 2017 (6 Month)
    Clint : QCON - Qatar Engineering & Construction Co.

    6) LAFFAN REFINERY - Qatar Petrochemical at Doha Qatar

    Designation : Instrument Technician


    Duration : 25 - May 2015 to 8 - April 2016 (1year)
    Clint : DOPET - Doha Petroleum Construction Co. Ltd.

    7) JGC - Japan Gas Corporation at Doha Qatar

    (BARZAN ONSHORE EPC PROJECT)


    Project type : LNG plant
    Designation : Instrument Technician
    Duration : 19 - September 2013 to 18 - February 2015 (1.6 year)
    Clint : TRAGS - Badge no: 10637
    8) N-KOM (Nakilat - Keppel Offshore & Marine Ltd) at Doha Qatar

    Designation : Instrument Technician


    Duration : 23 - May 2013 to 18 - August 2013 (3 Month)
    Clint : WALCO Middle East

    9) Occidental Petroleum Qatar Ltd (Oxy - Ps1) at Doha Qatar

    Designation : Instrument Technician


    Duration : 10 - February 2013 to 22 - March 2013 (1Month)
    Clint : DOPET - Doha Petroleum Construction Co. Ltd

    10) LNG (Liquefied natural gas) Train 3 at OMAN

    Designation : Instrument Technician


    Duration : 5 - February 2011 to 4 - December 2012 (11 Month)
    Clint : TOCO

    11) ONGC GAS Complexes at Hazira, India

    Designation : Instrument Technician


    Duration : November 2009 to October 2010 (1.2 Year)
    Clint : Flotomatic Engineers

    WELL HEAD & GAS COMPRESSOR WORK:

    ▪ Well Head Experience (offshore based). Hands on experience on Wellhead HSSS Penal, Cold set, Hot set
    & startup activity (Mack- PETRONAS)
    ▪ HSSS valve operation check like DHSV, MSASV, MV, WV, CV with interlock and Tripping (ESD, SIS,
    Fusible)
    ▪ HSSS penal Instrument loop check, Calibration, trouble shooting like PT- SIS (Yokogawa- EJA 530E), LT-
    FF ( Yocogawa- EJA 110E), Euro switch (Hydac), sov (Bifold).
    ▪ Well control panel: complete overhauling and testing of the well control Modules. Well versed with the
    logic involved with the well control panel. Make : PETRONAS
    ▪ Experience in trouble shooting, overhauling, installation and alignment of centrifugal multi stage gas
    compressors (HITACHI- Train 1, 2 3)
    ▪ Calibration, Trouble shooting, installation, like PT, TT, LT, Vibration prob, LP Flare gas recover
    compressors (screw compressor) (Mack- Howden)
    ▪ Configure wireless Transmitter PT; TT (Rosemount- 702DX) used new version- HART- TREX
    communicator.
    ▪ Working to VX Spectra (Gamma Detector) Model- 267CR.
    ▪ Control valve trouble shooting & Positionar Calibration (FF) (flowseser Lagix3400)
    ▪ Loop folder preparation

    Nature of Work:

    ▪ Worked on DCS (Centum-VP, Prosafe-RS) & PLC (Siemens-S7-400) Loop checking. Checking the I/O
    cards digital and analog.
    ▪ Calibrating, Installation and Commissioning of all type of Process Instrument Including Loop Testing in
    New Projects.
    ▪ Besides Project my Duties is too carried out Preventive Maintenance work as per ISO 9001-2000
    schedule. This also includes updating of Calibrating as well as Preventive Maintenance History Cards of
    Instruments.
    ▪ Carried out DCS/PLC Panel wiring as per Drawing in new Projects
    ▪ Maintenance and calibration of the control valves (Pneumatic, Smart & MOV,) Fisher – DVC6010,
    DVC6020, DVC6030, DVC2000, DVC6200) (Fisher Pneumatic positioned – 3582, 3682) (Masonielen –
    SVI-II 4P, SVI- II) (Samson – 3782I) Siemens, Neles, Valtel
    ▪ Experience with Calibration and Functional Checks of all types of Smart Instruments, Sensors and Final
    Control Elements.
    ▪ Field Modifications, Fault Diagnosis & Trouble Shooting.
    ▪ Interpretation of Loop Drawing, Instrument Cabling & Terminations, Cable Schedule, Hook-Up Drawing,
    and P&ID Drawings.
    ▪ Extensive Troubleshooting Experience for all Fields Instruments during Loop Check, Startup and
    Commissioning Activities.
    ▪ Generation and Maintenance of all types of Records for Quality Control Checks Including Calibration,
    Leak Checks and other Inspections.
    ▪ Servicing of SOVs, Boosters, Filters, Regulators and other accessories in control valves
    ▪ Instrumentation Data Sheet Verification.
    ▪ Punch List Clearance.
    ▪ Day to day activities (Job Distribution, Safety Talk, Permit authorization etc) with Central Control Room.

    Vibration Monitoring System (Bentley Nevada-3500 series)


    ▪ Loop checking of vibration transmitters from field to MMS system.
    ▪ Gap adjustment of Bentley Nevada vibration probes 3500, 3000.
    Fire & Gas system
    ▪ Calibration , loop checking and programming of FIRE & GAS instruments like gas Detectors, Smoke
    detectors, UV detectors manual call points, beacons and hooters etc
    ▪ Worked in DELUGE SYSTEM of TYCO FIRE AND GAS SYSTEM.
    ▪ Gas detectors make - Zellweger, Honeywell, Detronax.
    ▪ Flammable & toxic gas detectors (LEL,H2S & HYDROGEN)

    Control Valve Work:

     Control valve tests (Hydro tests, Seat Leakage, Body Mount Leakage, back pressure test,)
     Installation, Calibration, Overhauling, trouble shooting, service, Loping, Hydro Testing and maintenance
    in all kind of control valves (Fisher, Masoneilen, Nelas, Biffi, Nakakita, Valtek, Honeywell, Flowserve)
     Making work permit, test reports, daily reports.
     Hands on Good Experience on onsite lapping. With Lapping Machine
     Calibration of valve using positioners (Siemens, Abb, Fisher, Yamatech, Metso and MIL make electro
    pneumatic and pneumatic)
     Interface with customer plant personnel and Bay Valve Service personnel to perform hands-on
    workshop and valve troubleshooting / assessment, maintenance, testing, and / or repair of valves and
    actuators.
     Perform day-to-day Valve Service After cleaning to Area. Routine safety observations and inspections

    Have know Edge of Reading & Understanding


     P & ID  Piping Isometric
     Data Sheet  Cable Schedule
     Location Drawing  Junction box Schedule
     Loop Drawing  Panel Wiring Drawing
     Instrument Hook Up Drawing  Cable Routing Drawing
     Commissioning procedures
    Calibration Used Equipment
     HART Communicator 475,375 & 275  Loop calibrator, MA source (fluke)
     DRUCK-Digital pressure Indicator. Model (605,  Decade Box
    601, 610)  Temperature Bath (Jofra)
     Hydraulic Pressure Pump (Druck)  MV simulator (fluke)
     Multimeter (fluke)

    PERSONAL PROFILE
    NAME – JENISHKUMAR MANISHKUMAR NAVIK Passport No: U1151815
    Date of Birth & Place – 05 August 1990, Surat Date of Issue: 19-11-2019 Surat
    Religion – Hindu Date of Expiry: 18-11-2029
    Languages Know – Hindi, Gujarati, English ECNR – OK

    Declaration
    I hereby declare that all information stated above is true to the best of my knowledge.
    Jenish M.Navik

    You might also like