Part I System Information

Start Configuration
1.1 Reset to default:
Reset to factory default settings. The default
settings are shown with < > and bold.

Reset to default

1.2 Firmware Version:

Firmware Version

End Configuration

10
Part II System Setting
2.1 Interface:

Start Configuration

RS-232

< USB HID >

USB Virtual COM

End Configuration

11
Part III Keyboard wedge

parameters
3.1 Terminal Type:

Start Configuration

< IBM AT >

End Configuration

3.2 Language Selection:

Start Configuration

American

Italian

12
 Spanish

France

Germany

Japanese

End Configuration
Note:
Scan the barcode to select local keyboard
language, if your keyboard language can't be
found, please turn on ALT Mode which is an
alternate way to find your language.

13
3.3 Function Key Emulation:

Start Configuration

< Disable >

Enable

3.4 ALT Mode:

Start Configuration

< Disable >

Enable

14
3.5 Caps Lock :

< Disable >

Enable

3.6 Numeric Key:

< Disable >

Enable

End Configuration

Note 1:
ALT Mode can emulate most of local
keyboard languages in Microsoft system.
Note 2:
The barcode reader can emulate to
enable/disable Caps Lock key.
Note 3:
The barcode reader can emulate to
enable/disable Numeric Key.
15
3.7 Inter-Character Delay：

Start Configuration

Enable (00H, 00-64H*1msec)

3.8 Delay After Transmit (Keyboard

Enable(00H, 00-0AH*100msec)

3.9 Keyboard Speed:

Enable (00H, 00-08H)

16
3.10 Keyboard Wedge Terminator:

None

< CR >

TAB

ESC

End Configuration
Note:
Keyboard Wedge Terminator is to set up the
termination character of barcode reader
output to adapt to applications.

17
 Part IV RS-232 Protocol:
4.1 Baud Rate：

Start Configuration

1200bps

2400bps

4800bps

< 9600bps >

19200bps

38400bps

18
4.2 Data Bits:

7 Digits

< 8 Digits >

End Configuration

4.3 Stop Bits:

Start Configuration

< 1 Digit >

2 Digits

19
4.4 Parity Check:

< None >

Odd

Even

Mark

Space

4.5 Inter-Character Delay:

Enable (00H, 00-64H*1msec)

20
4.6 Delay After Transmit:

Enable (00H, 00-0AH*100msec)

4.7 Response Delay Time:

Enable (00H, 00-0AH*100msec)

End Configuration

Note:
Response Delay Time is the time of
barcode reader waiting for host to
response. The delay time=setting
data*100(ms).

21
4.8 Flow Control:

Start Configuration

< None >

RTS/CTS

ACK/NAK

Xon/Xoff

4.9 RS232- Interface Terminator:

None

< CR+LF >

22
 CR

LF

TAB

STX/ETX

EOT

End Configuration

Note:
RS232- Interface Terminator is to set up
the termination character of barcode
reader output to adapt to applications.

23
 Part V System Setting:
5.1 Scan Mode:

Start Configuration

Trigger Mode

< Auto Off Mode >

Continuous/Trigger Off Mode

Test Mode

Continuous Mode

Continuous/Timeout Off Mode

24
 Flash Mode

Continuous/No Trigger

End Configuration

Note:
Trigger Mode:
Press trigger to turn on scanner. To turn off
the scanner, just release trigger or after
barcode decoded.
Auto off Mode:
Press trigger to turn on scanner. Scanner
will be a utomatically off when time out or
after barcode decoded.
Continuous (Trigger Off) Mode:
Press trigger to activate continuous scan
mode. Scanner will keep scanning and
decoding barcodes.
If the same barcode is scanned, it will only
decode once. Press trigger again to turn off
the scanner.
Test Mode:
Press trigger to activate test mode, scanner
will scan and decode barcodes
continuously until trigger is pressed again.

25
Continuous Mode:
Press trigger to activate continuous scan
mode, scanner will keep scanning and
decoding barcodes. If the same barcode is
scanned, it will only decode once and the
red LED is always on.
Continuous (Timeout Off) Mode:
Press trigger to activate test mode.
Scanner will scan and decode barcodes
continuously until trigger is pressed again.
If the scanner doesn’ tdecode during
timeout, then the red LED will be off.
Flash Mode:
Press trigger to activate continuous scan
mode, the red LED will be on for 3 seconds
and then off for 3 seconds. If the decoding
is correct,
the red LED will be off immediately and
then proceed next flash cycle.
Continuous /No trigger Mode:
When turn on barcode reader, it will
activate Continuous /No trigger mode
automatically.

26
5.2 Buzzer
5.2.1 Buzzer Frequency:

Start Configuration

Low

Medium

< High >

End Configuration

5.2.2 Duration

Start Configuration

< Long >

Short

5.2.3 Power up Buzzer:

Disable

< Enable >

5.2.4 Good Read Buzzer:

Disable

< Enable >

End Configuration

28