Scribd Logo
Upload

Welcome to Scribd!

  • 1 views

    ASPHALT ROAD & PAVING QUALITY TEST

    Uploaded by

    Gleen Cabigas

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    ASPHALT ROAD & PAVING QUALITY TEST

    Uploaded by

    Gleen Cabigas
    1 views4 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    1 views4 pages

    ASPHALT ROAD & PAVING QUALITY TEST

    Uploaded by

    Gleen Cabigas

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 4

    ASPHALT ROAD & PAVING QUALITY TEST

    1. SUBBASE MATERIALS

    A. Subbase Gradation Requirement (MOC General Specifications, Sec. 3.02, Table 3.02-1)

    Frequency (MOC
    Sieve Sizes Grading I Grading II
    Sec. 3.02.6)
    62.5 mm (2inch) 100
    50 mm (2 inch) 90 - 100 100
    37.5 mm (1.5 inch) - 90 – 100
    25 mm (1 inch) - 55 – 85
    19 mm (3/4 inch) - 50 – 80
    1 lot (10,000 m2)
    9.5 mm (3/8 inch) - 40 – 70
    4.75 mm (No.4) 35 - 70 30 – 60
    2.54 mm (No. 10) - 20 – 50
    0.425 mm (No. 40) - 10 – 30
    0.075 mm (No. 200) 0 - 15 0 – 15

    B. Sand Equivalent 25 Min.


    C. Plasticity Index 6 Max.
    1 lot (10,000 m2)
    D. Abrasion Loss 50 Max.
    E. California Bearing Ratio 50 Min.

    2. BASE COURSE MATERIALS

    A. Aggregate Bases Gradation Requirement (MOC General Specifications, Sec. 3.03-1, Table
    3.03-1)

    Frequency (MOC
    Sieve Sizes Grading I Grading II Grading II
    Sec. 3.03.6)
    50 mm (2 inch) 100 - -
    37.5 mm (1.5 inch) - 100 -
    25 mm (1 inch) 55-85 70-95 100
    19 mm (3/4 inch) 50-80 55-85 70-100 1 lot (10,000 m2)
    4.75 mm (No.4) 30-60 30-60 35-65
    0.425 mm (No. 40) 10-25 10-25 15-25
    0.075 mm (No. 200) 3-10 3-10 3-10
    The fraction passing the No. 200 sieve shall not exceed the fraction passing the 0.425 mm
    (No. 40) sieve.

    B. Sodium Sulphate Soundness & Loss 12 Max. 1 lot (10,000 m2)


    C. Abrasion Loss 45 Max.
    D. Sand Equivalent 45 Min.
    E. Liquid Limit 25 Max.
    F. Plasticity Index 6 Max.
    G. California Bearing Ratio Grading I 100 Min.
    H. California Bearing Ratio Grading II 80 Min.
    I. California Bearing Ratio (CBR) Grading III 65 Min.

    3. PRIME COAT

    0.55-0.7 L/m2 (as per 10,000 m2 (as per


    A. Rate of Application SH3-01-UZA-CLB- SAES-Q-006 Sec.
    1324 1/3 R6) 5.3.1.A)

    4. TACK COAT

    0.25-0.35 L/m2 (as 10,000 m2 (as per


    B. Rate of Application per SH3-01-UZA-CLB- SAES-Q-006 Sec.
    1324 1/3 R6) 5.3.2.B)

    5. ASPHALT BINDER COURSE & WEARING COURSE

    Test Requirements Frequency (as per SAES-Q-006 Sec. 5.4.5)


    A. Penetration of Asphalt Binder 1/week or 1/lot
    B. Gradation of Fine and Coarse Aggregates 1/day or 1/lot
    C. Specific Gravity of Aggregates 1/week
    D. Resistance to Abrasion (LA) 1/month
    E. Magnesium Sulfate soundness 1/month
    F. Sand equivalent 1/month
    G. Plasticity Index 1/month
    H. Flat or elongated particles by weight 1/month
    I. Extraction/Grading 1/200 tons
    J. Marshall Properties 1/250 tons
    5 cores/ 1 day production or 10,000 m2
    K. Compaction & Thickness
    whichever is less

    Extraction/Grading (MOC Section 4.05)

    BITUMINOUS BASE COURSE


    GRADING I GRADING II GRADING III
    Sieve Size 32 mm (1-1/4 Inch) 22 mm (7/8 Inch) 19 mm (3/4 Inch)
    Nominal Maximum Nominal Maximum Nominal Maximum
    7.5 mm (1 1/2 inch) 100
    25 mm (1 inch) 75-90 100 100
    19.0 mm (3/4 inch) 65-80 75-90 90-100
    12.5 mm (1/2 inch) 55-70 65-80 78-93
    9.5 mm (3/8 inch) 45-60 55-65 57-72
    4.75 mm (No. 4) 31-46 35-60 43-58
    2.00 mm (No. 10) 18-33 20-35 28-43
    0.425 mm (No. 40) 5-18 7-20 13-28
    0.180 mm (No. 80) 3-13 5-25 -
    0.075 mm (No. 200) 2-9 3-7 3-7

    BITUMINOUS WEARING COURSE


    GRADING I GRADING II GRADING III
    Sieve Size 16 mm (5/8 Inch) 12.5 mm (1/2 In) 9.5 mm (3/8 Inch)
    Nominal Maximum Nominal Maximum Nominal Maximum
    19.0 mm (3/4 inch) 100 100
    12.5 mm (1/2 inch) 75-90 90-100 100
    9.5 mm (3/8 inch) 64-79 78-83 90-100
    4.75 mm (No. 4) 41-56 46-60 54-68
    2.00 mm (No. 10) 23-37 30-42 32-46
    0.425 mm (No. 40) 7-20 14-25 14-25
    0.180 mm (No. 80) 5-13 8-16 8-16
    0.075 mm (No. 200) 3-8 3-7 3-7

    Asphalt Binder & Wearing Course Quality Test (MOC Section 4.05)

    Bituminous Base Course Bituminous Wearing Course


    Quality Test
    Class A Class B Class C Class A Class B Class C
    Sodium Sulfate Soundness
    10 10 10 10 10 10
    Loss, Percent, Max.
    Abrasion Loss, Percent,
    20 20 20 20 20 20
    Max.
    Clay and Friable Particles,
    0.25 0.25 0.25 0.25 0.25 0.25
    Percent, Max.
    Sand Equivalent, Percent,
    45 45 45 45 45 45
    Min.

    75 Blow Marshall Properties


    Stability - Kg. min. 1000 750 500 1000 750 500
    Flow - mm 2-4 2-4 2-4 2-4 2-4 2-4
    Voids in Mineral
    Varies with Nominal Maximum Size per MS-2*
    Aggregate - Percent, Min.
    Voids in Mix - Percent 4-6 4-6 3-5 5-7 5-8 5-9
    Bituminous Material -
    4.0-6.0 4.0-6.1 4.0-6.2 3.0-6.0 3.0-6.1 3.0-6.2
    Percent of Total Weight
    Retained Strength -
    75 75 75 70 70 70
    Percent, Min.

    You might also like