Scribd
Upload
38 views21 pages

Test 1 - EmbeddedS

Btech

Uploaded by

utkarshrawat1090
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
38 views21 pages

Test 1 - EmbeddedS

Btech

Uploaded by

utkarshrawat1090
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 21

Test 1

Embedded System (ECE305)


ECE
VIth Sem.
Institute of Engineering and Technology
DDU Gorakhpur University
1. Embedded systems are

a) General Purpose

b) Special Purpose

c) Both

d) None
2. Embedded System is
a) An electronics system

b) A pure mechanical system

c) An electro-mechanical system

d) (a) & (c)


3. Little Endian processors
a) Store the lower-order byte of the data at the lowest address and vice-
versa
b) Store the higher-order byte of the data at the lowest address and vice-
versa
c) Store the both higher-order and lower-order byte of the data at the
same address and vice-versa
d) None
4. The instruction set of RISC processor is

a) Simple and lesser in number

b) Complex and lesser in number

c) Simple and larger in number

d) Complex and larger in number


5. Which of the following is true about CISC
processors?
a) The instruction set is non-orthogonal.

b) The number of general purpose registers is limited.

c) Instructions are like macros in C language.

d) Variable length instructions.

e) All

f) None
6. Which of the following processor architecture
supports easier instruction pipelining?
a) Harvard

b) Von Neumann

c) Both

d) None
7. Which of the following is one-time
programmable memory?
a) SRAM

b) PROM

c) FLASH

d) NVRAM
8. Which of the following is an example for
wireless communication interface?
a) RS232

b) Wi-Fi

c) Bluetooth

d) EEE1394

e) Both (b) & (c)


9. Which of the following is true about a
unipolar stepper motor?
a) Contains only a single winding per stator phase

b) Contains two winding per stator phase

c) Contains four windings per stator phase

d) None
10. What is the minimum number of interface lines
required for implementing I2C and SPI interface,
respectively?
a) 1,2

b) 4,2

c) 3,4

d) 2,4
11. What is EDLC:

a) Embedded Design Life Circuit

b) Embedded Design Life Cycle

c) Embedded Development Life Circuit

d) Embedded Development Life Cycle


12. The term ‘Model’ in EDLC represents

a) The various phases in the life cycle of the product

b) The various analysis of the product

c) The Various designs of the product

d) The various architecture of the product


13. Which EDLC model is shown in Figure?

a) Linear Model

b) Iterative Model

c) Evolutionary Model

d) Spiral Model

e) None
14. CAN bus is event-driven protocol for
communication. State True or false
a) True

b) False

c) Can’t say

d) None
15. Which of the following is true about LIN
bus?
a) Single master multiple slave interface

b) Low speed serial bus

c) Used for sensor/actuator interfacing

d) All

e) None
16. What is baud rate for serial communication
for PC?
a) 8800 bps

b) 9800 bps

c) 9600 bps

d) None
17. Which is not on-board communication
interface?
a) I2C

b) SPI

c) USART

d) Universal Serial Bus


18. Figure shows

a) Reset circuit

b) Watchdog circuit

c) Brown-out Protection circuit

d) RTC Circuit
19. Quality attributes of an embedded system are

a) Functional requirements

b) Non-functional requirements

c) Both

d) None
20. What is the minimum number of I/O line
required to interface a 16 key matrix keyboard?
a) 16

b) 8

c) 4

d) None of the above

You might also like