Scribd
Upload
20 views7 pages

Pac - Ed

Uploaded by

hackerrz.0077
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
20 views7 pages

Pac - Ed

Uploaded by

hackerrz.0077
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Marwadi University, Rajkot

Faculty of Engineering & Technology


Department of Mechanical Engineering

Academic Year: 2024-25

Subject: ED (01ME1103)
Sem : 1st

Student Classification & Action Taken

PAC Classification

Sr. no. PAC Classification Based on Result of Mid-1 exam Action Taken
Students have to solve first 5
1 Premium (P) Above 18 marks
Problems.
Students have to solve first 12
2 Average (A) Between 13 to 18 marks
Problems.
Students must solve all
3 Challenged (C) Below 13 marks
Problems.

Sr Description of Example Level as per


No. Blooms Taxonomy
1 Construct the plain scale of R.F. 1:50 to show metres and decimeters and
long enough to measure the length of 4 metres and 9 decimeters. Mark on Apply
the scalefollowing distances 1) 2.5 metres 2) 4 metres and 2 decimeters.
2 Draw an ellipse having major axis 120 mm and minor axis 80 mm by using
half ellipseby rectangle method and other half by concentric circle method. Apply

3 Draw F.V. and T.V of Figure Using 1st angle projection system.

Analyse

4 The front view of a line AB, 90mm long, measures 65mm. Front view is
inclined to XYline by 45°. Point A is 20mm below H.P. and on V.P. Point Analyse
B is in third quadrant. Draw
Marwadi University, Rajkot
Faculty of Engineering & Technology
Department of Mechanical Engineering

5 Using the first angle projection method, draw the following view for the
figure. Give the dimensions using the Aligned dimensioning method.(i) Full
Apply
Sectional front view (ii) Top view(iii) Left Hand Side View

6 Figure shows the front view and top view of an object. Draw the isometric
view.

Apply

7 A circle of 50 mm diameter rolls along a straight line without slipping.


Draw the curve traced out by point P on the periphery of the circle. Take
the initial position of the point at the bottom on the vertical centre line of Apply
the circle. Name the curve and also draw the normal and the tangent to the
curve at suitable point on curve.
8 The distance between end projectors of the straight line KL is 48 mm. The
end K is 20mm below H.P and 25 mm behind V.P. The end L is 12 mm
above H.P. and 40 mm infront of V.P. Draw the projections and finds the Analyse
true length of the line.
Marwadi University, Rajkot
Faculty of Engineering & Technology
Department of Mechanical Engineering

9 Draw F.V. and T.V of Figure Using 3rd angle projection system.

Apply

10 Draw the Front view and top view of given problem with 1st angel
projection

Apply
Marwadi University, Rajkot
Faculty of Engineering & Technology
Department of Mechanical Engineering

11 Draw the Front view and top view of given problem with 1st angel
projection

Apply

12 Draw the Front view and side view of given problem with 1st angel
projection

Apply
Marwadi University, Rajkot
Faculty of Engineering & Technology
Department of Mechanical Engineering

13 Draw the Front view and top view of given problem with 1st angel
projection

Apply

14 Draw the Front view and top view of given problem with 1st angel
projection

Apply

15 Draw isometric view from given F.V and LHSV Analyse


Marwadi University, Rajkot
Faculty of Engineering & Technology
Department of Mechanical Engineering

16 F.V and T.V of an object are given, Draw the isometric view

Analyse

17 F.V. and S.V of an object are given, Draw the isometric view.

Analyse

18 F.V and T.V of an object are given, Draw the isometric view
Analyse
Marwadi University, Rajkot
Faculty of Engineering & Technology
Department of Mechanical Engineering

19 Draw the projections of a regular hexagon of 25mm sides, having one of its
side in the H.P. and inclined at 60 to the V.P. and its surface making an
Apply
angle of 45º with the H.P.

20 ABCDE is a regular pentagonal plate of 40mm Sides, has its corner A on


the HP. The Plate is Inclined at 30° to the H.P. such that the side CD is
Apply
Parallel to both the reference plane. Draw the Projection of Plane.

You might also like