JCB WHEEL LOADER | 436 ZX

MAX. ENGINE POWER: 177hp (132kW)

MAX. OPERATING WEIGHT: 35860lb (16266kg)

MAX. LOADER CAPACITY: 3.5yd3 (2.7m3)

JCB WHEEL LOADER

G

J F

|
436ZX
E

H1
B C D

H A

STATIC DIMENSIONS

ft-in (mm) ft-in (mm)

A Overall length with standard bucket 23-6 (7169) Hinge pin height (maximum) 13-1 (3996)
B Axle to pivot pin 3-9 (1143) Overall operating height 17-4 (5305)
C Wheel Base 9-10 (3000) Front axle weight lb (kg) 14230 (6456)
D Axle to counterweight face 6-11 (1816) Rear axle weight lb (kg) 18660 (8466)
E Minimum ground clearance 1-6 (459) Total weight lb (kg) 32900 (14922)
F Height over exhaust 10-6 (3192) Inside radius 9-3 (2825)
G Width over cab 4-7 (1400) Maximum radius 19-4 (5900)
H Width over tires 8-6 (2597) Articulation angle degrees ±40°
H1 Wheel track 6-9 (2070)
J Height over cab 10-11 (3335)

Data based on machine equipped with a 3.1yd (2.4m ) bucket with bolt-on toeplates and Michelin 20.5R25 XHA (L3) tires.
3 3

Helping You Get

the Job Done!
 JCB WHEEL LOADER | 436 ZX

JCB WHEEL LOADER

LOADER DIMENSIONS CHANGES TO OPERATING PERFORMANCE AND DIMENSIONS

Tipping loads Dimensions

Op. weight Straight Full turn Vertical Width
Tire size Manufacturer Type Rating lb (kg) lb (kg) lb (kg) in (mm) in (mm)
20.5 - 25 (crossply) Goodyear SGL L2 -119 (-54) -71 (-32) -68 (-31) -0.354(-9 ) +0.197 (+5)
20.5 R 25 (radial) Goodyear GP-2B L2 +168 (+76) +99 (+45) +97 (+44) -0.354 (-9) +0.197 (+5)
20.5 R 25 (radial) Michelin XTLA L2 -353 (-160) -212 (-96) -205 (-93) -0.354 (-9) +0.197 (+5)
20.5 R 25 (radial) Michelin XHA L3 0 0 0 0 0
550/65 R 25 (radial) Michelin XLD L3 -265 (-120) -157 (-71) -157 (-69) 0 0
20.5 R 25 (radial) Michelin XRD1A L4 +1006 (+456) +600 (+272) +582 (+264) +1.142 (+29) +0.315 (+8)
20.5 R 25 (radial) Michelin XMINED2 L5 +1500 (+680) +897 (+407) +867 (+393) +1.142 (+29) -0.118 (-3)
20.5 R 25 (radial) Goodyear RL-5K L5 +1323 (+600) +789 (+358) +765 (+347) +1.142 (+29) -0.118 (-3)
XD counterweight +662 (+300) +1780 (+809) +1289 (+586) 0 0

|
436ZX
Assumes the machine is fitted with Michelin 20.5R25 XHA (L3) tires and XD counterweight

Bucket mounting Direct Direct Direct Direct Direct Quickhitch Quickhitch Quickhitch Quickhitch
Bucket type General purpose General purpose Penetration General purpose General purpose General purpose General purpose General purpose General purpose
Bucket equipment Tipped teeth Tipped teeth Tipped teeth Reversible toeplate Reversible toeplate Tipped teeth Tipped teeth Reversible toeplate Reversible toeplate
Bucket capacity (SAE heaped) yd3 (m3) 3.0 (2.3) 3.4 (2.6) 3.4 (2.6) 3.1 (2.4) 3.5 (2.7) 3.0 (2.3) 3.4 (2.6) 3.1 (2.4) 3.5 (2.7)
Bucket capacity (struck) yd3 (m3) 2.6 (2.0) 3.0 (2.3) 3.0 (2.3) 2.7 (2.1) 3.1 (2.3) 2.6 (2.0) 3.0 (2.3) 2.7 (2.1) 3.1 (2.3)
Bucket width ft-in (mm) 9-0 (2740) 9-0 (2740) 9-0 (2740) 8-10 (2700) 8-10 (2700) 9-0 (2740) 9-0 (2740) 8-10 (2700) 8-10 (2700)
Bucket weight lb (kg) 2750 (1250) 2897 (1317) 2994 (1361) 2776 (1262) 2924 (1329) 2473 (1124) 2638 (1199) 2499 (1136) 2664 (1211)
Maximum material density lb/yd3 (kg/m3) 3590 (2123) 3125 (1853) 3138 (1861) 3468 (2032) 3031 (1782) 3435 (2032) 2991 (1774) 3294 (1930) 2901 (1705)
Tipping load straight lb (kg) 25880 (11737) 25558 (11591) 25650 (11633) 25851 (11724) 25529 (11578) 24764 (11231) 24440(11084) 24543 (11131) 24404 (11068)
Tipping load full turn lb (kg) 21540 (9769) 21253 (9639) 21344 (9680) 21509 (9755) 21223 (9625) 20612 (9348) 20343 (9226) 20427 (9264) 20314 (9213)
Payload lb (kg) 10769 (4884) 10628 (4820) 10672 (4840) 10753 (4877) 10610 (4812) 10306 (4674) 10171 (4613) 10213 (4632) 10156 (4606)
Maximum break out force lbf (kN) 39565 (176) 36418 (162) 36418 (162) 39565 (176) 36418 (162) 35294 (157) 32371 (144) 35294 (157) 32371 (144)
M Dump angle maximum degrees 47° 47° 47° 47° 47° 47° 47° 47° 47°
N Roll back angle at full height degrees 58° 58° 58° 58° 58° 58° 58° 58° 58°
O Roll back at carry degrees 45° 45° 45° 45° 45° 45° 45° 45° 45°
P Roll back at ground level degrees 37° 37° 37° 37° 37° 37° 37° 37° 37°
Q Load over height ft-in (mm) 12-3 (3755) 12-3 (3755) 12-3 (3755) 12-3 (3755) 12-3 (3755) 12-3 (3755) 12-3 (3755) 12-3 (3755) 12-3 (3755)
R Dump height (45° dump) ft-in (mm) 9-4 (2843) 9-1 (2778) 9-1 (2778) 9-9 (2965) 9-6 (2833) 9-1 (2758) 8-10 (2693) 9-5 (2880) 9-0 (2748)
S Dig depth ft-in (mm) 0-4 (113) 0-4 (113) 0-4 (113) 0-4 (105) 0-4 (105) 0-4 (113) 0-4 (113) 0-4 (105) 0-4 (105)
T Reach at dump height ft-in (mm) 4-1 (1254) 4-4 (1318) 4-4 (1318) 3-9 (1144) 3-7 (1103) 4-5 (1339) 4-7 (1403) 4-0 (1229) 3-11 (1188)
Reach maximum (45° dump) ft-in (mm) 6-7 (2006) 6-9 (2070) 6-9 (2070) 6-3 (1896) 6-5 (1947) 6-10 (2083) 7-1 (2147) 6-6 (1973) 6-8 (2024)
Operating weight (includes 176lb. (80kg) operator and full fuel tank) lb (kg) 33714 (15290) 33862 (15357) 33959 (15401) 33740 (15302) 33888 (15369) 34369 (15587) 34517 (15654) 34395 (15599) 34543 (15666)
Helping You Get
the Job Done!
 JCB WHEEL LOADER | 436 ZX

JCB WHEEL LOADER

LOADER STEERING

Heavy duty three cylinder Z-bar geometry provides high breakout forces with excellent loading characteristics. The pin, Priority steering hydraulic system with emergency ground driven pump. Piston pump meters flow through steer valve @
bushing and seal design on all pivot points provide extended maintenance intervals. 2756 lb/in2 (190bar) to provide smooth low effort response. Steering angle ± 40°. Steering cylinders located high in the
chassis fabrication to provide protection from damage. Adjustable steering column.

ENGINE
BRAKES
6-cylinder wastegated turbo-charged, liquid cooled, direct injection diesel. Air-to-air charge air cooling ensures low
emissions and “clean-burn” combustion chamber provides minimum fuel consumption. A remote sump oil drain facility
Hydraulic power braking on all wheels, operating pressure 1160psi (80 bar). Dual circuit with accumulator back-up provide
simplifies servicing.
maximum safety under all conditions. Outboard mounted, oil immersed, multi-plate disc brakes with organic brake linings
Type 4 stroke direct injection are environmentally acceptable. Parking brake, mechanical disc type operating on transmission output shaft.
Model BTAA5.9C
Capacity in 3 (liters) 360 (5.9)
TIRES
Bore in (mm) 4.0 (102)
Stroke in (mm) 4.75 (120) A variety of tire options are available including:

|
Aspiration Turbo charged 20.5 x 25 x 12 ply (L2). 20.5 x 25 SGL (L2). 20.5R25 XTLA (L2). 550/65R25 XLD (L3). 20.5R25 XHA (L3).

436 ZX
Cylinders 6 20.5R25 XRD1A (L4). 20.5R25 XMINED2 (L5). 20.5R25 RL-5K (L5).
Max gross power to SAE J1995/ISO 14396 hp (kW) @ 2000rpm 179 (132)
Rated gross power to SAE J1995/ISO 14396 hp (kW) @ 2200rpm 173 (129)
Nett power to SAE J1349/EEC 80/1269 hp (kW) @ 2200rpm 165 (123)
Max torque lbf.ft (Nm) @ 1300rpm 580 (786 ) LOADER HYDRAULICS
Emissions:-
Twin variable displacement piston pumps feed a “load sensing” system providing a fuel efficient and responsive distribution of
Relevant standards EUNR MM Stage 2 USA CFR Part 89
power as required. Main services are servo actuated from a single lever (joystick) loader control. Auxiliary circuit controlled
(Complies with EU/EPA “Off Highway” Construction Equipment Regulation Tier 2).
via additional lever or joystick mounted electrical buttons. Accumulator back-up is available to control loader in the event of
loss of pump pressure.
TRANSMISSION
4 wheel drive, automatic smooth shift countershaft transmission electrically operated selector and gear change
incorporating a speed inhibitor and modulation for smooth, responsive on-the-move direction and ratio changes. Single Pump type Twin variable displacement piston pumps
stage integral torque converter. 4 forward and 3 reverse gears. Pump 1 max. flow gal/min (l/min) 35 (132)
Type Smooth shift powershift Pump 1 max. pressure lb/in2 (bar) 3625 (250)
Make & model ZF 4WG 190 Pump 2 max. flow gal/min (l/min) 35 (132)
Torque converter stall ratio 2.873 : 1 Pump 2 max. pressure lb/in2 (bar) 2320 (160)
1st gear mph (kph) 5.1 (8.2) Hydraulic cycle times at full engine revs seconds
2nd gear mph (kph) 9.0 (14.5) Arms raise (full bucket) 5.9
3rd gear mph (kph) 16.8 (27) Bucket dump (full bucket) 1.0
4th gear (forward only) mph (kph) 23.5 (37.9) Arms lower (empty bucket) 3.4
Total cycle 10.3

AXLES
Cylinder dimensions Bore Rod Closed centers Stroke
Type Epicyclic hub reduction Bucket x1 in (mm) 6.3 (160) 3.1 (80) 47.2 (1200) 21.1 (536)
Make & model Graziano PR12 B.O. front and rear Lift x2 in (mm) 5.1 (130) 2.8 (70) 49.6 (1259) 32.0 (813)
Overall axle ratio 21.098 : 1 Steer x2 in (mm) 3.1 (80) 2.0 (50) 24.4 (621) 12.3 (312)
Rear axle oscillation 21°
Helping You Get
the Job Done!
 JCB WHEEL LOADER | 436 ZX

JCB WHEEL LOADER

ELECTRICAL SYSTEM STANDARD EQUIPMENT
24 volt negative ground system, 70 Amp alternator with 2 x 126 Amp hour low maintenance batteries. Isolator located in Loader: Bucket reset mechanism, loader arm kickout mechanism, loader control isolator, single lever servo control, high
rear of machine. Ignition key start/stop and pre-heat cold start. Primary fuse box. Other electrical equipment includes breakout forces with excellent loading characteristics.
quartz halogen, twin filament working lights, front/rear wash/wipe, heated rear window, full road going lights, clock, gauge Engine: Air cleaner – 2 stage dry type – cyclonic with primary and safety elements, sedimenter, twin bowl fuel filters,
and warning light monitoring. Connectors to IP67 standard. alternator and air conditioning compressor drive belt guards, isolated cooling pack with hydraulically driven cooling fan.
System voltage Volt 24 Transmission: Single lever shift control, speed inhibitor, neutral start, disconnect on footbrake and loader lever,
Alternator output Amp hour 70 disconnect isolator switch, direction changes and kickdown on gear selector and loader control lever.
Battery capacity Amp hour 2 x 145 Axles: Epicyclic wheel hub reduction, fixed front, oscillating rear.
Cold cranking capacity cca 850 Brakes: Multi-plate wet disc brakes, organic linings, dual circuit hydraulic power. Parking disc brake on transmission
output shaft.
Hydraulics: Twin piston pumps with priority steer, emergency steer back-up, 2 spool loader circuit with accumulator
CAB support, 3rd spool auxiliary hydraulic circuit as standard. Hydraulic tank located in the rear chassis fabrication.
Steering: Adjustable steering column, “soft feel” steering wheel 5 turns lock to lock, resilient stops on max lock.
Resiliently mounted ROPS/FOPS structure (tested in accordance with ISO 3471-1 : 1986 / ISO 3449 : 1984). Deluxe
operator environment combines ergonomically located controls with a high level of appointment and low internal noise Cab: ROPS/FOPS safety structure, cigar lighter, ashtray, interior reading light, center mounted master warning light.

|
levels. Entry/exit is via large rear hinged door and anti-slip steps. Excellent forward visibility is provided by a 3 section Electronic monitoring panel with LCD message display. Two speed intermittent front windshield wiper, single speed rear

436ZX
curved, laminated windshield and low waistline. Extensive instrumentation includes electronic monitoring panel and windshield wiper. 3 speed heater/demisting with replaceable air filter, LH and RH opening windows, sun visor, sun blind,
display (EMS). Heating / ventilation provides balanced and filtered air distribution throughout the cab via a powerful internal rear view mirror, heated external mirrors, adjustable suspension seat with belt and headrest, operator storage
37,530BTU/hr (11kW) capacity heater. The unitary construction allows easy sealing and prevents ingress of dust. A facilities, laminated windshield, heated rear window, loader control isolator, horn, fire extinguisher.
transmission lock on the selector prevents inadvertent engagement and the loader controls can be isolated for safe road Electrical: Road lights front and rear, parking lights, front and rear working lights, reverse alarm and light, rear fog light,
travel. Noise level measured in accordance with 86/662/EEC, amendment 95/27/EC battery isolator, radio wiring and speakers, 70 amp alternator, rotating beacon.
Interior pressure level : 74 Lp (A)
Bodywork: Front and rear fenders, side and rear access panels, flexible bottom step, full width rear counterweight,
recovery hitch, lifting lugs, engine and transmission underguarding.

ATTACHMENTS

An extensive range of attachments are available to fit directly or via the JCB quickhitch mounting.

SERVICE FILL CAPACITIES OPTIONAL EQUIPMENT

gal (liters) Air conditioning, limited slip differentials front/rear axles, additional counterweight, oil bath air cleaner, turbo 2
Hydraulic system 55 (210) pre-cleaner, visibowl pre-cleaner, tooth guard, replaceable bucket wearparts, sealed alternator, epoxy coated
radiator/coolers, stainless steel brake pipes, Smooth ride system (SRS), hydraulic quickhitch, full rear fenders, reversing
Fuel tank 61 (230)
camera (colour), auto greasing system, 4 spool auxiliary circuit, auxiliary control buttons on joystick, spark arrestor,
Engine oil sump 3.7 (14) 24V to 12V in cab converter, cab screen guards, air suspension seat, front chassis apron mat, light guards, engine block
Transmission oil system 7 (27) heater, biodegradable oils, cabfiltration optional.
Axle oil (front) 10.3 (39)
Axle oil (rear) 9.8 (37)
Engine coolant system 9 (35)

Helping You Get

the Job Done!
 JCB WHEEL LOADER | 436 ZX

JCB WHEEL LOADER

BUCKET SELECTOR
F
Loose density Fill factor
Material lb/yd3 kg/m3 %
Snow (fresh) 337 200 110
Peat (dry) 674 400 100
Sugar beet 894 530 100
Coke (loose) 961 570 85
E Barley 1012 600 85
Petroleum coke 1146 680 85
D Wheat 1231 730 85
Coal bitumous 1290 765 100
Fertilizer (mixed) 1737 1030 85
A Coal anthracite 1764 1046 100
C
B Earth (dry) (loose) 1939 1150 100

|
Nitrate fertilizer 2180 1250 85

436 ZX
Sodium chloride (dry) (salt) 2192 1300 85
LOADER DIMENSIONS – FORK FRAME WITH FORKS Cement Portland 2428 1440 100
Limestone (crushed) 2580 1530 100
Assumes the fitment of Michelin 20.5R25 XHA (L3) tires
Sand (dry) 2613 1550 100
Fork carriage width ft-in (mm) 4-11 (1500)
Asphalt 2698 1600 100
Length of tines ft-in (mm) 4-0 (1220)
Gravel (dry) 2782 1650 85
A Reach at ground level ft-in (mm) 2-7 (798)
Clay (wet) 2832 1680 110
B Reach at arms horizontal ft-in (mm) 5-4 (1620)
Sand (wet) 3187 1890 110
C Below ground level ft-in (mm) 0-5⁄8 (16)
Fire clay 3507 2080 100
D Arms, horizontal height ft-in (mm) 6-4 (1936)
Copper (concentrate) 3878 2300 85
E Arms, maximum height ft-in (mm) 12-6 (3818)
Slate 4721 2800 100
F Reach at maximum height ft-in (mm) 2-10 (869)
Magnetite 5402 3204 100
Payload* lb (kg) 12368 (5610)
Tipping load straight lb (kg) 18274 (8289)
Tipping load full turn (40°) lb (kg) 15461 (7013)
Attachment weight lb (kg) 1063 (482)
*At the center-of-gravity distance 1ft-51⁄2in (500mm). Based on 80% of full turn tipping load as defined by ISO 8313.
Manual fork spacings at 2in (50mm) increments. Fork section 4in x 2in (100mm x 50mm). 3.5
Bucket capacity (yd3)

3.4

3.3

3.1

3.0
100%

115% 95% 1350 1685 2025 2360 2700 3035 3370 3710
Material density (lb/yd3) Helping You Get
Bucket fill factors the Job Done!
 JCB WHEEL LOADER | 436 ZX

JCB WHEEL LOADER

THE BEST BACK-UP IN THE BUSINESS
Buy any JCB model and you’ll get a complete deal that extends beyond that of any rival.

FINANCE PARTS

Your JCB Dealer can meet your financial needs through a variety of plans for leasing, JCB Dealers’ convenient locations offer excellent ‘over the counter’ parts availability.
lease purchases with or without options, installment sales contracts and rental programs.

WARRANTY REGIONAL PARTS DEPOTS

|
JCB machines are covered by JCB’s one year standard warranty, which is outlined in the For the breakdown part your dealer may not have in stock, JCB has SDD ‘Same Day Dispatch,’

436 ZX
JCB ‘Certificate of Warranty’. Extended warranty coverage is also available. from one of two parts distribution centers in the United States and one in Canada.
Contact your JCB Dealer for details.

SERVICE

JCB Dealer service people are committed to keeping your JCB up and running. JCB Dealer
mechanics are enrolled in on-going training programs and supported by experienced JCB
Service Representatives based throughout North America.

982

JCB Inc, PO Box 18306, Savannah, GA 31418. Tel: (912) 447-2000. Fax: (912) 447-2299. www.jcb.com
JCB reserves the right to change specifications without notice. Illustrations shown may include optional equipment and accessories. The JCB logo is a registered trademark of J C Bamford Excavators Ltd. USA 20140-3/06-1SS 1
Helping You Get
the Job Done!