SGS_ 2411133 _812676_683683_Rev.0_MountAnalysis_Pass_T-Mobile_133ft_11.29.2024

Date: November 29, 2024
Sinnott Gering and Schmitt Towers, Inc.

14708 Custer Rd Suite 102
Omaha, NE 68138
(844) 886-9377
[email protected]
Subject: Mount Analysis Report
Carrier Designation: T-Mobile Equipment Change-Out

Carrier Site Number: 9SV0751A
Carrier Site Name: N/A
Crown Castle Designation: Crown Castle BU Number: 812676

Crown Castle Site Name: North Beaufort
Crown Castle JDE Job Number: 2128610
Crown Castle Order Number: 683683 Rev.0
Engineering Firm Designation: SGS Towers Report Designation: 2411133
Site Data: 110 Bay Pines Road, Beaufort, Beaufort County, SC, 29902
Latitude 32° 27' 47.90" Longitude -80° 45' 41.20"
Structure Information: Structure Height & Type: 150 ft Monopole Tower

Mount Elevation: 133 ft
Mount Type: 10.0 ft Platform Mount
Sinnott Gering and Schmitt Towers, Inc. is pleased to submit this “Mount Analysis Report” to determine the structural
integrity of T-Mobile’s antenna mounting system with the proposed appurtenance and equipment addition on the
abovementioned supporting structure. Analysis of the existing supporting structure is to be completed by others and therefore
is not part of this analysis. Analysis of the antenna mounting system as a tie-off point for fall protection or rigging is not part
of this document.
The purpose of the analysis is to determine acceptability of the mount stress level. Based on our analysis we have determined
the mount stress level to be:
Platform Mount Sufficient
This analysis has been performed in accordance with the 2021 International Building Code based upon an ultimate 3-second
gust wind speed of 138 mph. Applicable standard references and design criteria are listed in Section 2 - Analysis Criteria.
Mount analysis prepared by: Pavitra Prabhu DRS

Respectfully Submitted by:
November 29, 2024
10.0 ft Platform – Mount Analysis CCI BU No 812676
Order 683683, Revision 0 Page 2
TABLE OF CONTENTS
1) INTRODUCTION
2) ANALYSIS CRITERIA
Table 1 - Proposed Equipment Configuration
3) ANALYSIS PROCEDURE
Table 2 - Documents Provided
3.1) Analysis Method
3.2) Assumptions
4) ANALYSIS RESULTS
Table 3 - Mount Component Stresses vs. Capacity
4.1) Recommendations
5) APPENDIX A
Wire Frame and Rendered Models
6) APPENDIX B
Software Input Calculations
7) APPENDIX C
Software Analysis Output
8) APPENDIX D
Additional Calculations
November 29, 2024
1) INTRODUCTION
This is an existing 3-Sector, 10.0-ft Platform mount, designed by Kenwood [Part#T1507KTHD]. The mount model is
updated based on the available photos.
2) ANALYSIS CRITERIA
Building Code: 2021 IBC
TIA-222 Revision: TIA-222-H
Risk Category: II
Ultimate Wind Speed: 138 mph
Exposure Category: C
Topographic Factor at Base: 1.0
Topographic Factor at Mount: 1.0
Ice Thickness: 0.50 in
Wind Speed with Ice: 30 mph
Seismic Ss: 0.592
Seismic S1: 0.189
Live Loading Wind Speed: 30 mph
Man Live Load at Mid/End-Points: 250 lb
Man Live Load at Mount Pipes: 500 lb
Table 1 - Proposed Equipment Configuration

Mount Antenna Number Mount /
Antenna
Centerline Centerline of Antenna Model Modification
Manufacturer
(ft) (ft) Antennas Details
3 COMMSCOPE FFVV-65C-R3-V1_TMO
136
3 ERICSSON AIR 6419 B41_TMO_CCIV2 10’ Platform
133
3 ERICSSON RADIO 4460 B2/B25 B66_TMO Mount
135
3 ERICSSON RADIO 4480 B71_TMO
3) ANALYSIS PROCEDURE
Table 2 - Documents Provided

Document Remarks Reference Source
Morrison Hershfield / Project Number. CN12-
Previous Structural Analysis 11841919 CCI
464R2 / 2400001, dated 11/21/2024
GPD Group / Report No. 2021777.812676.01.
Previous Mount Analysis - CCI
dated 05/26/2021
Crown Castle, Application No. 683683 Rev.0,
Crown Application - CCI
dated 11/12/2024
3.1) Analysis Method
RISA-3D (Version 22.0.1), a commercially available analysis software package, was used to create a three-
dimensional model of the antenna mounting system and calculate member stresses for various loading cases.
This analysis was performed in accordance with Crown Castle’s ENG-SOW-10208 Tower Mount Analysis
(Revision E).
November 29, 2024
3.2) Assumptions
1) The antenna mounting system was properly fabricated, installed and maintained in good condition
in accordance with its original design and manufacturer's specifications.
2) The configuration of antennas, mounts, and other appurtenances are as specified in Table 1 and
the referenced drawings.
3) All member connections are assumed to have been designed to meet or exceed the load carrying
capacity of the connected member unless otherwise specified in this report.
4) Structural steel material grades have been considered based on the applicable ASTM
specifications per AISC, unless verified by the associated mount manufacturer design
specifications. Refer to the RISA-3D output report for material grades utilized in this analysis.
This analysis may be affected if any assumptions are not valid or have been made in error. SGS Towers
should be notified to determine the effect on the structural integrity of the antenna mounting system.
4) ANALYSIS RESULTS
Table 3 - Mount Component Stresses vs. Capacity (Platform, All Sectors)

Critical Centerline
Notes Component % Capacity Pass / Fail
Member (ft)
1,3 Side Plate SPL10 102.6 Acceptable
1 Support Rail SR2 85.6 Pass
1 Corner Plate CPL6 69.5 Pass
1 Antenna Mast Pipe 1b 59.1 Pass
1 Standoff SO2 133 35.2 Pass
1 Grating Angle GA6 34.0 Pass
1 Plate Von Mises P99 73.8 Pass
2 Plate Weld Check - 53.6 Pass
2 Mount to Tower Connection - 39.9 Pass
Structure Rating (max from all components) = 102.6%

Notes:
1) See additional documentation in "Appendix C - Software Analysis Output" for calculations supporting the % capacity
consumed.
2) See additional documentation in "Appendix D - Additional Calculations" for calculations supporting the % capacity
consumed.
3) A structure rating of 105% or less is within engineering tolerances and considered acceptable.
4.1) Recommendations
The mount has sufficient capacity to carry the proposed loading configuration. No modifications are required
at this time.
November 29, 2024
APPENDIX A
WIRE FRAME AND RENDERED MODELS

A1/B1/C1
ERICSSON I AIR 6419 B41_TMO_CCIV2
A2/B2/C2
COMMSCOPE I FFVV-65C-R3-V1_TMO
ERICSSON I RADIO 4460 B2/B25 B66_TMO
ERICSSON I RADIO 4480 B71_TMO
SGS Towers, Inc. 812676 (NORTH BEAUFORT) SK-1

Pavitra Prabhu Nov 29, 2024 at 01:04 PM
2411133 Mount Rendering & Antenna Configuration Mount Rushmore 2024-10-14.r3d
2411133 Nodal Labels Mount Rushmore 2024-10-14.r3d
2411133 Loading - Dead Mount Rushmore 2024-10-14.r3d
2411133 Loading - Wind 0° Mount Rushmore 2024-10-14.r3d
2411133 Loading - Wind 90° Mount Rushmore 2024-10-14.r3d
November 29, 2024
APPENDIX B
SOFTWARE INPUT CALCULATIONS

SGS Project No.: 2411133
Project: 812676 (NORTH BEAUFORT)
November 29, 2024
Mount Analysis per TIA-222-H-2017 - Add. 1 (Nov. 2019) and the 2021 IBC.
Basic Wind Speeds and Site Parameters
Wind Wind
Load Cases
Speed Pressure
V qz
(mph) (lb/ft2)
No Ice (Bare) 138 62.168
Ice 30 2.938
Maintenance 30 2.938
Design Ice Thickness ti 0.5 in
Risk Category II TIA-222-H - Table 2-1

Exposure Category C TIA-222-H - 2.6.5.1.2
Topographic factor K zt 1.000 TIA-222-H - 2.6.6.2.2
Ground Elevation zs 33.76 ft
Mount Elevation CL z 133 ft
Design Parameters Summary

Velocity pressure coefficient Kz 1.344 TIA-222-H - 2.6.5.2
Rooftop wind speed-up factor Ks (N/A) TIA-222-H - 2.6.7
Ground elevation factor Ke 0.999 TIA-222-H - 2.6.8
Wind direction probability factor Kd 0.950 TIA-222-H - 16.6
Gust effect factor Gh 1.000 TIA-222-H - 16.6
Shielding factor Ka 0.900 TIA-222-H - 16.6
Radial ice thickness t iz 0.575 in TIA-222-H - 2.6.10
Seismic Parameters Summary

Seismic site class D (Default)
Spectral response, short Ss 0.592
Spectral response, 1 s S1 0.189
Design spectral response, 1 s S D1 0.280 TIA-222-H - 2.7.5
Design spectral response, short S DS 0.523 TIA-222-H - 2.7.5
Response modification coeff. R 2 TIA-222-H - 16.7
Seismic response coefficient CS 0.262 TIA-222-H - 16.7
Earthquake amplification factor AS 1 TIA-222-H - 16.7
Weight of mount + appurtenances D, W 2,808 lb
Vertical seismic load effects Ev 294 lb TIA-222-H - 2.7.6

Horizontal seismic load effects Eh 735 lb TIA-222-H - 2.7.7
Maintenance Parameters Summary

Vertical, at mount pipes LM 500 lb
Vertical, on horizontal members L V 250 lb
This document and the information disclosed within, including the document structure and contents, are confidential and the proprietary property of Sinnott, Gering, and Schmitt
Towers, Inc. and are protected by patent, copyright and/or other proprietary rights. Any disclosure to a third party in whole or in part in any manner is expressly prohibited without
the prior written permission of Sinnott, Gering, and Schmitt Towers, Inc.
Effective date: 2024-10-14
Project: 812676 (NORTH BEAUFORT)
November 29, 2024
Appurtenance Loading Summary

Wind Force
Appurtenance: Make, Model Qty Height Width Depth Weight Shape Front Side
(in) (in) (in) (lb) (lb) (lb)
ERICSSON | AIR 6419 B41_TMO_CCIV2 3 34.49 19.92 7.99 81.84 Flat 320 137
COMMSCOPE | FFVV-65C-R3-V1_TMO 3 95.90 25.20 9.30 124.60 Flat 725 274
ERICSSON | RADIO 4460 B2/B25 B66_TMO 3 17.00 15.10 11.90 109.00 Flat 120 94
ERICSSON | RADIO 4480 B71_TMO 3 21.80 15.70 7.50 92.60 Flat 160 77
This document and the information disclosed within, including the document structure and contents, are confidential and the proprietary property of Sinnott, Gering, and Schmitt
Towers, Inc. and are protected by patent, copyright and/or other proprietary rights. Any disclosure to a third party in whole or in part in any manner is expressly prohibited without
the prior written permission of Sinnott, Gering, and Schmitt Towers, Inc.
Effective date: 2024-10-14
ASCE Hazards Report
Address: Standard: ASCE/SEI 7-16 Latitude: 32.4633
No Address at This Location Risk Category: II Longitude: -80.7614
Soil Class: D - Stiff Soil Elevation: 33.76635774719008 ft
(NAVD 88)
Wind
Results:
Wind Speed 138 Vmph
10-year MRI 76 Vmph
25-year MRI 87 Vmph
50-year MRI 96 Vmph
100-year MRI 105 Vmph
Data Source: ASCE/SEI 7-16, Fig. 26.5-1B and Figs. CC.2-1–CC.2-4, and Section 26.5.2
Date Accessed: Mon Nov 25 2024
Value provided is 3-second gust wind speeds at 33 ft above ground for Exposure C Category, based on linear
interpolation between contours. Wind speeds are interpolated in accordance with the 7-16 Standard. Wind speeds
correspond to approximately a 7% probability of exceedance in 50 years (annual exceedance probability =
0.00143, MRI = 700 years).
Site is in a hurricane-prone region as defined in ASCE/SEI 7-16 Section 26.2. Glazed openings need not be
protected against wind-borne debris.
https://ascehazardtool.org/ Page 1 of 3 Mon Nov 25 2024

Seismic
Site Soil Class: D - Stiff Soil

Results:
SS : 0.592 S D1 : 0.28
S1 : 0.189 TL : 8
Fa : 1.326 PGA : 0.341
Fv : 2.223 PGA M : 0.429
S MS : 0.785 F PGA : 1.259
S M1 : 0.419 Ie : 1
S DS : 0.523 Cv : 1.095
Seismic Design MCE R Response Spectrum

Category: D Design Response Spectrum
Sa (g) vs T(s) Sa (g) vs T(s)
MCER Vertical Response Spectrum Design Vertical Response Spectrum
Sa (g) vs T(s) Sa (g) vs T(s)
Data Accessed: Mon Nov 25 2024

Date Source:
USGS Seismic Design Maps based on ASCE/SEI 7-16 and ASCE/SEI 7-16 Table 1.5-2. Additional data for
site-specific ground motion procedures in accordance with ASCE/SEI 7-16 Ch. 21 are available from USGS.

Ice
Results:
Ice Thickness: 0.50 in.
Concurrent Temperature: 15 F
Gust Speed 30 mph
Data Source: Standard ASCE/SEI 7-16, Figs. 10-2 through 10-8
Date Accessed: Mon Nov 25 2024
Ice thicknesses on structures in exposed locations at elevations higher than the surrounding terrain and in valleys
and gorges may exceed the mapped values.
Values provided are equivalent radial ice thicknesses due to freezing rain with concurrent 3-second gust speeds,
for a 500-year mean recurrence interval, and temperatures concurrent with ice thicknesses due to freezing rain.
Thicknesses for ice accretions caused by other sources shall be obtained from local meteorological studies. Ice
thicknesses in exposed locations at elevations higher than the surrounding terrain and in valleys and gorges may
exceed the mapped values.
The ASCE Hazard Tool is provided for your convenience, for informational purposes only, and is provided “as is” and without warranties of any
kind. The location data included herein has been obtained from information developed, produced, and maintained by third party providers; or
has been extrapolated from maps incorporated in the ASCE standard. While ASCE has made every effort to use data obtained from reliable
sources or methodologies, ASCE does not make any representations or warranties as to the accuracy, completeness, reliability, currency, or
quality of any data provided herein. Any third-party links provided by this Tool should not be construed as an endorsement, affiliation,
relationship, or sponsorship of such third-party content by or from ASCE.
ASCE does not intend, nor should anyone interpret, the results provided by this Tool to replace the sound judgment of a competent
professional, having knowledge and experience in the appropriate field(s) of practice, nor to substitute for the standard of care required of such
professionals in interpreting and applying the contents of this Tool or the ASCE standard.
In using this Tool, you expressly assume all risks associated with your use. Under no circumstances shall ASCE or its officers, directors,
employees, members, affiliates, or agents be liable to you or any other person for any direct, indirect, special, incidental, or consequential
damages arising from or related to your use of, or reliance on, the Tool or any information obtained therein. To the fullest extent permitted by
law, you agree to release and hold harmless ASCE from any and all liability of any nature arising out of or resulting from any use of data
provided by the ASCE Hazard Tool.

November 29, 2024
APPENDIX C
SOFTWARE ANALYSIS OUTPUT

2411133 Unity Bending Check Mount Rushmore 2024-10-14.r3d
2411133 Shear Check Mount Rushmore 2024-10-14.r3d
2411133 Plate Von Mises Mount Rushmore 2024-10-14.r3d
Company : SGS Towers, Inc. 11/29/2024
Designer : Pavitra Prabhu 1:07:33 PM
Job Number : 2411133 Checked By : __________
Model Name : 812676 (NORTH BEAUFORT)
Basic Load Cases

BLC Description Category Y Gravity Nodal Point Distributed Area(Member)
1 Bare Weight None -1 54 3
2 Ice Weight None 54 182 3
3 Wind (bare) 0° None 66 364
10 Wind (bare) 210° None 66 364
11 Wind (bare) 240° None 66 364
12 Wind (bare) 270° None 66 364
13 Wind (bare) 300° None 66 364
14 Wind (bare) 330° None 66 364
15 Wind (ice) 0° None 66 364
16 Wind (ice) 30° None 66 364
17 Wind (ice) 60° None 66 364
18 Wind (ice) 90° None 66 364
19 Wind (ice) 120° None 66 364
20 Wind (ice) 150° None 66 364
21 Wind (ice) 180° None 66 364
22 Wind (ice) 210° None 66 364
23 Wind (ice) 240° None 66 364
24 Wind (ice) 270° None 66 364
25 Wind (ice) 300° None 66 364
26 Wind (ice) 330° None 66 364
27 Wind (maint.) 0° None 66 364
31 Wind (maint.) 120° None 66 364
32 Wind (maint.) 150° None 66 364
33 Wind (maint.) 180° None 66 364
34 Wind (maint.) 210° None 66 364
35 Wind (maint.) 240° None 66 364
36 Wind (maint.) 270° None 66 364
37 Wind (maint.) 300° None 66 364
38 Wind (maint.) 330° None 66 364
39 Maint. - (Lm) - P1 None 1
48 Maint. - (Lv) - M1 - I-End None 1
51 Maint. - (Lv) - M1 - Middle None 1
54 Maint. - (Lv) - M1 - J-End None 1
RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 1

Basic Load Cases (Continued)

BLC Description Category Y Gravity Nodal Point Distributed Area(Member)
57 Seismic - Ev (Y) None 63
58 Seismic - Eh (X) None 63
59 Seismic - Eh (Z) None 63
60 BLC 1 Transient Area Loads None 6
61 BLC 2 Transient Area Loads None 6
Load Combinations
Description Solve P-Delta BLC Factor BLC Factor BLC Factor
1 Wind - (1.2D + 1.0Wo) - 0° Yes Y 1 1.2 3 1
2 Wind - (1.2D + 1.0Wo) - 30° Yes Y 1 1.2 4 1
3 Wind - (1.2D + 1.0Wo) - 60° Yes Y 1 1.2 5 1
4 Wind - (1.2D + 1.0Wo) - 90° Yes Y 1 1.2 6 1
5 Wind - (1.2D + 1.0Wo) - 120° Yes Y 1 1.2 7 1
6 Wind - (1.2D + 1.0Wo) - 150° Yes Y 1 1.2 8 1
7 Wind - (1.2D + 1.0Wo) - 180° Yes Y 1 1.2 9 1
8 Wind - (1.2D + 1.0Wo) - 210° Yes Y 1 1.2 10 1
9 Wind - (1.2D + 1.0Wo) - 240° Yes Y 1 1.2 11 1
10 Wind - (1.2D + 1.0Wo) - 270° Yes Y 1 1.2 12 1
11 Wind - (1.2D + 1.0Wo) - 300° Yes Y 1 1.2 13 1
12 Wind - (1.2D + 1.0Wo) - 330° Yes Y 1 1.2 14 1
13 Ice - (1.2D + 1.0Di + 10 Wi) - 0° Yes Y 1 1.2 2 1 15 1
14 Ice - (1.2D + 1.0Di + 10 Wi) - 30° Yes Y 1 1.2 2 1 16 1
15 Ice - (1.2D + 1.0Di + 10 Wi) - 60° Yes Y 1 1.2 2 1 17 1
16 Ice - (1.2D + 1.0Di + 10 Wi) - 90° Yes Y 1 1.2 2 1 18 1
17 Ice - (1.2D + 1.0Di + 10 Wi) - 120° Yes Y 1 1.2 2 1 19 1
18 Ice - (1.2D + 1.0Di + 10 Wi) - 150° Yes Y 1 1.2 2 1 20 1
19 Ice - (1.2D + 1.0Di + 10 Wi) - 180° Yes Y 1 1.2 2 1 21 1
20 Ice - (1.2D + 1.0Di + 10 Wi) - 210° Yes Y 1 1.2 2 1 22 1
21 Ice - (1.2D + 1.0Di + 10 Wi) - 240° Yes Y 1 1.2 2 1 23 1
22 Ice - (1.2D + 1.0Di + 10 Wi) - 270° Yes Y 1 1.2 2 1 24 1
23 Ice - (1.2D + 1.0Di + 10 Wi) - 300° Yes Y 1 1.2 2 1 25 1
24 Ice - (1.2D + 1.0Di + 10 Wi) - 330° Yes Y 1 1.2 2 1 26 1
25 Dead - (1.4D) Yes Y 1 1.4
26 Maint. - (1.2D + 1.5Lm + 1.0Wm) - P1 - 0° Yes Y 1 1.2 39 1.5 27 1

Load Combinations (Continued)


Load Combinations (Continued)

134 Maint. - (1.2D + 1.5Lv) - M1 - I-End Yes Y 1 1.2 48 1.5
137 Maint. - (1.2D + 1.5Lv) - M1 - Middle Yes Y 1 1.2 51 1.5
140 Maint. - (1.2D + 1.5Lv) - M1 - J-End Yes Y 1 1.2 54 1.5
143 Seismic - (1.2D + 1.0Ev + 1.0Eh) (X-dir.) Yes Y 1 1.2 57 1 58 1
144 Seismic - (1.2D + 1.0Ev + 1.0Eh) (Z-dir.) Yes Y 1 1.2 57 1 59 1
Node Boundary Conditions

Node Label X [k/in] Y [k/in] Z [k/in]
1 N40 Reaction Reaction Reaction

Node Boundary Conditions (Continued)

Node Label X [k/in] Y [k/in] Z [k/in]
Member Primary Data

Label I Node J Node Rotate(deg) Section/Shape Type Design List Material Design Rule
1 1b N255 N254 Antenna Mast Pipe Beam HSS Pipe A53 Gr.B Typical
2 1c N260 N259 Antenna Mast Pipe Beam HSS Pipe A53 Gr.B Typical
3 1a N251 N250 Antenna Mast Pipe Beam HSS Pipe A53 Gr.B Typical
4 CPL1 N169 N178 Corner Plate Beam None A36 Gr.36 Typical
16 FH1 N277 N278 Face Horizontal (Square) Beam None A500 Gr.B Rect Typical
19 GA1 N185 N184 Grating Angle Beam None A36 Gr.36 Typical
25 ICA1 N188 N192 Inner Cross Arm Beam None A500 Gr.B Rect Typical
31 OCA1 N2 N114 Outer Cross Arm Beam None A500 Gr.B Rect Typical
37 R1 N227 N190 RIGID None None RIGID Typical
39 R3 1 N248 RIGID None None RIGID Typical
44 R8 N196 N237 120 RIGID None None RIGID Typical

Member Primary Data (Continued)



144 SPL1 N194 N198 Side Plate Beam None A36 Gr.36 Typical
156 SO1 N186 N189 Standoff Beam None A500 Gr.B Rect Typical
159 SR2 N264 N265 Support Rail Beam None A53 Gr.B Typical


160 SRCPL1 N309 N310 180 Support Rail Corner Plate Beam None A36 Gr.36 Typical
165 M166 7 N499 RIGID None None RIGID Typical
168 M169 N488 N492 RIGID None None RIGID Typical
171 3b N489 N503 120 Antenna Mast Pipe Beam HSS Pipe A53 Gr.B Typical
172 3c N496 N504 120 Antenna Mast Pipe Beam HSS Pipe A53 Gr.B Typical
173 3a N493 N490 120 Antenna Mast Pipe Beam HSS Pipe A53 Gr.B Typical
180 2b N507 N521 240 Antenna Mast Pipe Beam HSS Pipe A53 Gr.B Typical
181 2c N514 N522 240 Antenna Mast Pipe Beam HSS Pipe A53 Gr.B Typical
182 2a N511 N508 240 Antenna Mast Pipe Beam HSS Pipe A53 Gr.B Typical
Member Advanced Data

Label Col-Wall Vert Release I Offset [in] J Offset [in] Physical Deflection Ratio Options Seismic DR
1 1b Yes Default None
2 1c Yes Default None
3 1a Yes Default None
4 CPL1 Yes N/A None
5 CPL2 Yes N/A None
6 CPL3 Yes N/A None
7 CPL4 Yes N/A None
8 CPL5 Yes N/A None
9 CPL6 Yes N/A None
10 CPL7 Yes N/A None
16 FH1 Yes N/A None
17 FH2 Yes N/A None
18 FH3 Yes N/A None
19 GA1 Yes N/A None
20 GA2 Yes N/A None
21 GA3 Yes N/A None
22 GA4 Yes N/A None
23 GA5 Yes N/A None
24 GA6 Yes N/A None
25 ICA1 2 0.188 Yes N/A None

Member Advanced Data (Continued)

31 OCA1 2 Yes N/A None
37 R1 Yes ** NA ** None


123 R100 Yes ** NA ** None
124 R101 Yes ** NA ** None
125 R102 Yes ** NA ** None
126 R103 Yes ** NA ** None
127 R104 Yes ** NA ** None
128 R105 Yes ** NA ** None
129 R106 Yes ** NA ** None
130 R107 Yes ** NA ** None
131 R108 Yes ** NA ** None
132 R109 Yes ** NA ** None
133 R110 Yes ** NA ** None
134 R111 Yes ** NA ** None
135 R112 Yes ** NA ** None
136 R113 Yes ** NA ** None
137 R114 Yes ** NA ** None
138 R115 Yes ** NA ** None
139 R116 Yes ** NA ** None


140 R117 Yes ** NA ** None
141 R118 Yes ** NA ** None
142 R119 Yes ** NA ** None
143 R120 Yes ** NA ** None
144 SPL1 Yes N/A None
156 SO1 0.625 Yes N/A None
159 SR2 Yes N/A None
160 SRCPL1 Yes N/A None
165 M166 Yes ** NA ** None
166 M167 Yes ** NA ** None
167 M168 Yes ** NA ** None
168 M169 Yes ** NA ** None
169 M170 Yes ** NA ** None
170 M171 Yes ** NA ** None
174 M175 Yes ** NA ** None
175 M176 Yes ** NA ** None
176 M177 Yes ** NA ** None
177 M178 Yes ** NA ** None
178 M179 Yes ** NA ** None
179 M180 Yes ** NA ** None
Hot Rolled Steel Properties

Label E [ksi] G [ksi] Nu Therm. Coeff. [1e⁵°F⁻¹] Density [lb/ft³] Yield [ksi] Ry Fu [ksi] Rt
1 A992 29000 11154 0.3 0.65 490 50 1.1 65 1.1
2 A36 Gr.36 29000 11154 0.3 0.65 490 36 1.5 58 1.2
3 A572 Gr.50 29000 11154 0.3 0.65 490 50 1.1 65 1.1
4 A500 Gr.B RND 29000 11154 0.3 0.65 527 42 1.4 58 1.3
5 A500 Gr.B Rect 29000 11154 0.3 0.65 527 46 1.4 58 1.3
6 A53 Gr.B 29000 11154 0.3 0.65 490 35 1.6 60 1.2
7 A1085 29000 11154 0.3 0.65 490 50 1.4 65 1.3

General Materials Properties

Label E [ksi] G [ksi] Nu Therm. Coeff. [1e⁵°F⁻¹] Density [lb/ft³] Plate Methodology
1 gen_Conc3NW 3155 1372 0.15 0.6 145 Isotropic
2 gen_Conc4NW 3644 1584 0.15 0.6 145 Isotropic
3 gen_Conc3LW 2085 906 0.15 0.6 109.999 Isotropic
4 gen_Conc4LW 2408 1047 0.15 0.6 109.999 Isotropic
5 gen_Alum 10100 4077 0.3 1.29 173 Isotropic
6 gen_Steel 29000 11154 0.3 0.65 490 Isotropic
7 gen_Plywood 1800 38 0 0.3 35 Isotropic
8 RIGID 1e+6 0.3 0 0 Isotropic
Hot Rolled Steel Section Sets

Label Shape Type Design List Material Design RuleArea [in²]Iyy [in⁴]Izz [in⁴]J [in⁴]
1 Standoff HSS4X4X6 Beam None A500 Gr.B Rect Typical 4.78 10.3 10.3 17.5
2 Inner Cross Arm HSS3X3X3 Beam None A500 Gr.B Rect Typical 1.89 2.46 2.46 4.03
3 Outer Cross Arm HSS4X4X4 Beam None A500 Gr.B Rect Typical 3.37 7.8 7.8 12.8
4 Face Horizontal (Square) HSS3.5X3.5X4 Beam None A500 Gr.B Rect Typical 2.91 5.04 5.04 8.35
5 Face Horizontal (Round) PIPE_3.0 Beam None A53 Gr.B Typical 2.07 2.85 2.85 5.69
6 Support Rail Corner Plate L7.19X4.73X5 Beam None A36 Gr.36 Typical 3.627 7.046 19.802 0.114
7 Grating Angle L2X2X3 Beam None A36 Gr.36 Typical 0.722 0.271 0.271 0.009
8 Corner Plate 0.375"X7"WIDEPLATEBeam None A36 Gr.36 Typical 2.625 0.031 10.719 0.119
9 Side Plate 0.375"X6"WIDEPLATEBeam None A36 Gr.36 Typical 2.25 0.026 6.75 0.101
10 Support Rail PIPE_2.0 Beam None A53 Gr.B Typical 1.02 0.627 0.627 1.25
11 Antenna Mast Pipe PIPE_2.5 Beam HSS Pipe A53 Gr.B Typical 1.61 1.45 1.45 2.89
General Section Sets

Label Type Material Area [in²] Iyy [in⁴] Izz [in⁴] J [in⁴]
1 RIGID None RIGID 1e+6 1e+6 1e+6 1e+6
Hot Rolled Steel Design Parameters

Label Shape Length [in] Lcomp top [in] K y-y K z-z Channel Conn. a [in] Function
1 1b Antenna Mast Pipe 120 Lbyy N/A N/A Lateral
2 1c Antenna Mast Pipe 120 Lbyy N/A N/A Lateral
3 1a Antenna Mast Pipe 120 Lbyy N/A N/A Lateral
4 CPL1 Corner Plate 8.25 Lbyy N/A N/A Lateral
16 FH1 Face Horizontal (Square) 120 Lbyy N/A N/A Lateral
19 GA1 Grating Angle 28.29 Lbyy 0.65 0.65 N/A N/A Lateral

Hot Rolled Steel Design Parameters (Continued)

Label Shape Length [in] Lcomp top [in] K y-y K z-z Channel Conn. a [in] Function
25 ICA1 Inner Cross Arm 30.778 Lbyy N/A N/A Lateral
31 OCA1 Outer Cross Arm 16 Lbyy N/A N/A Lateral
37 SPL1 Side Plate 3.4 Lbyy N/A N/A Lateral
49 SO1 Standoff 39.6 Lbyy N/A N/A Lateral
52 SR2 Support Rail 108 Lbyy N/A N/A Lateral
53 SRCPL1 Support Rail Corner Plate 34.79 Lbyy N/A N/A Lateral
Plate Primary Data

Label A Node B Node C Node D Node Material Thickness [in]
1 P7 N43 N49 N60 N61 gen_Steel 0.625
2 P8 N61 N60 N62 N63 gen_Steel 0.625
3 P9 N63 N62 N64 N65 gen_Steel 0.625
4 P10 N65 N64 N48 N42 gen_Steel 0.625
5 P11 N57 N43 N61 N59 gen_Steel 0.625
6 P12 N59 N61 N63 N51 gen_Steel 0.625
7 P13 N51 N63 N65 N58 gen_Steel 0.625
8 P14 N58 N65 N42 N55 gen_Steel 0.625
9 P15 N49 N66 N67 N60 gen_Steel 0.625
10 P16 N60 N67 N68 N62 gen_Steel 0.625
11 P17 N62 N68 N69 N64 gen_Steel 0.625

Plate Primary Data (Continued)

12 P18 N64 N69 N70 N48 gen_Steel 0.625
13 P19 N66 N37 N71 N67 gen_Steel 0.625
14 P20 N67 N71 N31 N68 gen_Steel 0.625
15 P21 N68 N31 N72 N69 gen_Steel 0.625
16 P22 N69 N72 N35 N70 gen_Steel 0.625
17 P24 N78 N77 N49 N43 gen_Steel 0.625
18 P27 N76 N80 N81 N45 gen_Steel 0.625
19 P31 N41 N47 N76 N73 gen_Steel 0.625
20 P32 N73 N76 N45 N39 gen_Steel 0.625
21 P33 N39 N45 N77 N78 gen_Steel 0.625
22 P34 N56 N41 N73 N75 gen_Steel 0.625
23 P35 N75 N73 N39 N53 gen_Steel 0.625
24 P36 N81 N33 N84 N82 gen_Steel 0.625
25 P37 N53 N39 N78 N74 gen_Steel 0.625
26 P38 N74 N78 N43 N57 gen_Steel 0.625
27 P39 N47 N79 N80 N76 gen_Steel 0.625
28 P40 N82 N84 N37 N66 gen_Steel 0.625
29 P41 N45 N81 N82 N77 gen_Steel 0.625
30 P42 N77 N82 N66 N49 gen_Steel 0.625
31 P43 N79 N36 N83 N80 gen_Steel 0.625
32 P44 N80 N83 N33 N81 gen_Steel 0.625
33 P46 N92 N91 N47 N41 gen_Steel 0.625
34 P49 N88 N94 N95 N89 gen_Steel 0.625
35 P53 N40 N46 N88 N85 gen_Steel 0.625
36 P54 N85 N88 N89 N90 gen_Steel 0.625
37 P55 N90 N89 N91 N92 gen_Steel 0.625
38 P56 N54 N40 N85 N87 gen_Steel 0.625
39 P57 N87 N85 N90 N50 gen_Steel 0.625
40 P58 N95 N30 N98 N96 gen_Steel 0.625
41 P59 N50 N90 N92 N86 gen_Steel 0.625
42 P60 N86 N92 N41 N56 gen_Steel 0.625
43 P61 N46 N93 N94 N88 gen_Steel 0.625
44 P62 N96 N98 N36 N79 gen_Steel 0.625
45 P63 N89 N95 N96 N91 gen_Steel 0.625
46 P64 N91 N96 N79 N47 gen_Steel 0.625
47 P65 N93 N34 N97 N94 gen_Steel 0.625
48 P66 N94 N97 N30 N95 gen_Steel 0.625
49 P68 N104 N103 N46 N40 gen_Steel 0.625
50 P71 N102 N105 N106 N44 gen_Steel 0.625
51 P75 N42 N48 N102 N99 gen_Steel 0.625
52 P76 N99 N102 N44 N38 gen_Steel 0.625
53 P77 N38 N44 N103 N104 gen_Steel 0.625
54 P78 N55 N42 N99 N101 gen_Steel 0.625
55 P79 N101 N99 N38 N52 gen_Steel 0.625
56 P80 N106 N32 N109 N107 gen_Steel 0.625
57 P81 N52 N38 N104 N100 gen_Steel 0.625
58 P82 N100 N104 N40 N54 gen_Steel 0.625
59 P83 N48 N70 N105 N102 gen_Steel 0.625
60 P84 N107 N109 N34 N93 gen_Steel 0.625
61 P85 N44 N106 N107 N103 gen_Steel 0.625
62 P86 N103 N107 N93 N46 gen_Steel 0.625
63 P87 N70 N35 N108 N105 gen_Steel 0.625
64 P88 N105 N108 N32 N106 gen_Steel 0.625
65 P67 N336 N337 N372 N344 gen_Steel 0.625
66 P69 N347 N390 N391 N386 gen_Steel 0.625


67 P70 N356 N367 N338 N331 gen_Steel 0.625
68 P72 N385 N384 N388 N355 gen_Steel 0.625
69 P73 N369 N374 N343 N370 gen_Steel 0.625
70 P74 N328 N354 N365 N366 gen_Steel 0.625
71 P89 N358 N375 N325 N350 gen_Steel 0.625
72 P90 N366 N365 N361 N367 gen_Steel 0.625
73 P91 N367 N361 N368 N338 gen_Steel 0.625
74 P92 N338 N368 N333 N348 gen_Steel 0.625
75 P93 N384 N386 N387 N388 gen_Steel 0.625
76 P94 N363 N328 N366 N364 gen_Steel 0.625
77 P95 N344 N372 N340 N351 gen_Steel 0.625
78 P96 N368 N369 N370 N333 gen_Steel 0.625
79 P97 N364 N366 N367 N356 gen_Steel 0.625
80 P98 N379 N345 N341 N380 gen_Steel 0.625
81 P99 N331 N338 N348 N359 gen_Steel 0.625
82 P100 N339 N383 N379 N353 gen_Steel 0.625
83 P101 N388 N387 N339 N389 gen_Steel 0.625
84 P102 N354 N336 N344 N365 gen_Steel 0.625
85 P103 N365 N344 N351 N361 gen_Steel 0.625
86 P104 N390 N326 N330 N391 gen_Steel 0.625
87 P105 N361 N351 N369 N368 gen_Steel 0.625
88 P106 N351 N340 N374 N369 gen_Steel 0.625
89 P107 N360 N329 N375 N358 gen_Steel 0.625
90 P108 N398 N397 N347 N346 gen_Steel 0.625
91 P109 N349 N378 N354 N328 gen_Steel 0.625
92 P110 N324 N346 N384 N385 gen_Steel 0.625
93 P111 N352 N381 N362 N378 gen_Steel 0.625
94 P112 N362 N382 N337 N336 gen_Steel 0.625
95 P113 N377 N380 N381 N352 gen_Steel 0.625
96 P114 N380 N341 N342 N381 gen_Steel 0.625
97 P115 N353 N379 N380 N377 gen_Steel 0.625
98 P116 N329 N353 N377 N375 gen_Steel 0.625
99 P117 N378 N362 N336 N354 gen_Steel 0.625
100 P118 N375 N377 N352 N325 gen_Steel 0.625
101 P119 N373 N389 N329 N360 gen_Steel 0.625
102 P120 N386 N391 N392 N387 gen_Steel 0.625
103 P121 N325 N352 N378 N349 gen_Steel 0.625
104 P122 N381 N342 N382 N362 gen_Steel 0.625
105 P123 N350 N325 N349 N376 gen_Steel 0.625
106 P124 N376 N349 N328 N363 gen_Steel 0.625
107 P125 N389 N339 N353 N329 gen_Steel 0.625
108 P126 N391 N330 N323 N392 gen_Steel 0.625
109 P127 N335 N398 N346 N324 gen_Steel 0.625
110 P128 N346 N347 N386 N384 gen_Steel 0.625
111 P129 N392 N323 N393 N383 gen_Steel 0.625
112 P130 N355 N388 N389 N373 gen_Steel 0.625
113 P131 N383 N393 N345 N379 gen_Steel 0.625
114 P132 N387 N392 N383 N339 gen_Steel 0.625
115 P133 N396 N399 N371 N334 gen_Steel 0.625
116 P134 N348 N333 N396 N394 gen_Steel 0.625
117 P135 N394 N396 N334 N332 gen_Steel 0.625
118 P136 N332 N334 N397 N398 gen_Steel 0.625
119 P137 N359 N348 N394 N395 gen_Steel 0.625
120 P138 N395 N394 N332 N357 gen_Steel 0.625
121 P139 N371 N327 N402 N400 gen_Steel 0.625


122 P140 N357 N332 N398 N335 gen_Steel 0.625
123 P141 N333 N370 N399 N396 gen_Steel 0.625
124 P142 N400 N402 N326 N390 gen_Steel 0.625
125 P143 N334 N371 N400 N397 gen_Steel 0.625
126 P144 N397 N400 N390 N347 gen_Steel 0.625
127 P145 N370 N343 N401 N399 gen_Steel 0.625
128 P146 N399 N401 N327 N371 gen_Steel 0.625
129 P147 N416 N417 N452 N424 gen_Steel 0.625
130 P148 N427 N470 N471 N466 gen_Steel 0.625
131 P149 N436 N447 N418 N411 gen_Steel 0.625
132 P150 N465 N464 N468 N435 gen_Steel 0.625
133 P151 N449 N454 N423 N450 gen_Steel 0.625
134 P152 N408 N434 N445 N446 gen_Steel 0.625
135 P153 N438 N455 N405 N430 gen_Steel 0.625
136 P154 N446 N445 N441 N447 gen_Steel 0.625
137 P155 N447 N441 N448 N418 gen_Steel 0.625
138 P156 N418 N448 N413 N428 gen_Steel 0.625
139 P157 N464 N466 N467 N468 gen_Steel 0.625
140 P158 N443 N408 N446 N444 gen_Steel 0.625
141 P159 N424 N452 N420 N431 gen_Steel 0.625
142 P160 N448 N449 N450 N413 gen_Steel 0.625
143 P161 N444 N446 N447 N436 gen_Steel 0.625
144 P162 N459 N425 N421 N460 gen_Steel 0.625
145 P163 N411 N418 N428 N439 gen_Steel 0.625
146 P164 N419 N463 N459 N433 gen_Steel 0.625
147 P165 N468 N467 N419 N469 gen_Steel 0.625
148 P166 N434 N416 N424 N445 gen_Steel 0.625
149 P167 N445 N424 N431 N441 gen_Steel 0.625
150 P168 N470 N406 N410 N471 gen_Steel 0.625
151 P169 N441 N431 N449 N448 gen_Steel 0.625
152 P170 N431 N420 N454 N449 gen_Steel 0.625
153 P171 N440 N409 N455 N438 gen_Steel 0.625
154 P172 N478 N477 N427 N426 gen_Steel 0.625
155 P173 N429 N458 N434 N408 gen_Steel 0.625
156 P174 N404 N426 N464 N465 gen_Steel 0.625
157 P175 N432 N461 N442 N458 gen_Steel 0.625
158 P176 N442 N462 N417 N416 gen_Steel 0.625
159 P177 N457 N460 N461 N432 gen_Steel 0.625
160 P178 N460 N421 N422 N461 gen_Steel 0.625
161 P179 N433 N459 N460 N457 gen_Steel 0.625
162 P180 N409 N433 N457 N455 gen_Steel 0.625
163 P181 N458 N442 N416 N434 gen_Steel 0.625
164 P182 N455 N457 N432 N405 gen_Steel 0.625
165 P183 N453 N469 N409 N440 gen_Steel 0.625
166 P184 N466 N471 N472 N467 gen_Steel 0.625
167 P185 N405 N432 N458 N429 gen_Steel 0.625
168 P186 N461 N422 N462 N442 gen_Steel 0.625
169 P187 N430 N405 N429 N456 gen_Steel 0.625
170 P188 N456 N429 N408 N443 gen_Steel 0.625
171 P189 N469 N419 N433 N409 gen_Steel 0.625
172 P190 N471 N410 N403 N472 gen_Steel 0.625
173 P191 N415 N478 N426 N404 gen_Steel 0.625
174 P192 N426 N427 N466 N464 gen_Steel 0.625
175 P193 N472 N403 N473 N463 gen_Steel 0.625
176 P194 N435 N468 N469 N453 gen_Steel 0.625


177 P195 N463 N473 N425 N459 gen_Steel 0.625
178 P196 N467 N472 N463 N419 gen_Steel 0.625
179 P197 N476 N479 N451 N414 gen_Steel 0.625
180 P198 N428 N413 N476 N474 gen_Steel 0.625
181 P199 N474 N476 N414 N412 gen_Steel 0.625
182 P200 N412 N414 N477 N478 gen_Steel 0.625
183 P201 N439 N428 N474 N475 gen_Steel 0.625
184 P202 N475 N474 N412 N437 gen_Steel 0.625
185 P203 N451 N407 N482 N480 gen_Steel 0.625
186 P204 N437 N412 N478 N415 gen_Steel 0.625
187 P205 N413 N450 N479 N476 gen_Steel 0.625
188 P206 N480 N482 N406 N470 gen_Steel 0.625
189 P207 N414 N451 N480 N477 gen_Steel 0.625
190 P208 N477 N480 N470 N427 gen_Steel 0.625
191 P209 N450 N423 N481 N479 gen_Steel 0.625
192 P210 N479 N481 N407 N451 gen_Steel 0.625
Envelope Node Reactions

Node Label X [lb] LC Y [lb] LC Z [lb] LC MX [lb-ft] LC MY [lb-ft] LC MZ [lb-ft] LC
1 N40 max 2878.986 7 1314.438 11 401.508 3 0 144 0 144 0 144
2 min -7148.318 1 -697.224 5 -352.704 9 0 1 0 1 0 1
3 N41 max 3040.735 7 1197.003 3 371.524 6 0 144 0 144 0 144
4 min -7197.674 1 -652.758 9 -481.729 12 0 1 0 1 0 1
5 N42 max 8109.169 1 1215.272 11 1232.611 10 0 144 0 144 0 144
6 min -4157.036 7 -599.272 5 -1271.289 4 0 1 0 1 0 1
7 N43 max 8059.812 1 1114.54 3 1311.065 10 0 144 0 144 0 144
8 min -3995.287 7 -568.633 9 -1191.963 4 0 1 0 1 0 1
9 N328 max 2218.993 2 1195.348 11 7019.461 9 0 144 0 144 0 144
10 min -4363.202 8 -665.746 5 -3558.037 3 0 1 0 1 0 1
11 N329 max 3768.942 9 1279.934 11 2709.869 3 0 144 0 144 0 144
12 min -1508.694 3 -747.957 5 -6341.792 9 0 1 0 1 0 1
13 N346 max 3622.957 8 1332.17 7 2616.78 3 0 144 0 144 0 144
14 min -1490.587 2 -699.664 1 -6334.242 9 0 1 0 1 0 1
15 N348 max 2097.757 2 1236.37 7 7237.698 9 0 144 0 144 0 144
16 min -4100.856 8 -601.141 1 -3703.444 3 0 1 0 1 0 1
17 N408 max 1629.818 11 783.751 55 2979.829 11 0 144 0 144 0 144
18 min -3541.034 5 -225.53 12 -6574.07 5 0 1 0 1 0 1
19 N409 max 3107.8 5 786.498 55 5833.81 5 0 144 0 144 0 144
20 min -1120.386 11 -246.207 12 -2079.472 11 0 1 0 1 0 1
21 N426 max 3238.069 5 975.028 4 5650.877 5 0 144 0 144 0 144
22 min -1110.043 11 -328.093 10 -1966.194 11 0 1 0 1 0 1
23 N428 max 1722.749 11 945.413 4 3045.426 11 0 144 0 144 0 144
24 min -3764.593 5 -296.412 10 -6552.719 5 0 1 0 1 0 1
25 Totals: max 5350.725 1 4926.153 16 5350.844 10
26 min -5350.722 7 3482.593 10 -5350.848 4
Plate Von Mises / (Φ * Fy) = 23.897 ksi / (0.9 * 36 ksi) = 0.738

Envelope Plate Principal Stresses
Plate Surface Sigma1 [ksi] LC Sigma2 [ksi] LC Tau Max [ksi] LC Angle [rad] LC Von Mises [ksi] LC
1 P99 max T 13.47 3 4.823 3 8.425 9 1.91 12 23.034 9
2 min -9.398 9 -26.248 9 0.539 1 -0.181 1 1.086 1
3 max B 27.204 9 9.598 9 8.803 9 1.88 2 23.897 9
4 min -4.812 3 -13.65 3 0.675 1 -0.584 1 1.504 1
5 P94 max T 12.994 3 4.632 3 8.29 9 2.23 12 22.675 9

Envelope Plate Principal Stresses (Continued)

6 min -9.259 9 -25.84 9 0.484 5 -0.034 1 0.885 5
7 max B 26.811 9 9.498 9 8.657 9 1.749 1 23.546 9
8 min -4.749 3 -13.28 3 0.734 5 -0.721 12 1.283 5
9 P14 max T 13.213 7 4.689 7 8.252 1 1.896 4 22.527 1
10 min -9.159 1 -25.664 1 0.446 5 -0.65 5 0.871 5
11 max B 26.699 1 9.463 1 8.618 1 1.893 6 23.447 1
12 min -4.796 7 -13.499 7 0.773 5 -0.266 5 1.34 5
13 P11 max T 12.766 7 4.593 7 8.191 1 1.953 4 22.444 1
14 min -9.199 1 -25.582 1 0.56 9 -0.054 5 1.16 9
15 max B 26.477 1 9.334 1 8.572 1 1.775 5 23.26 1
16 min -4.596 7 -12.952 7 0.636 9 -0.489 4 1.496 9
17 P137 max T 12.896 3 3.949 3 8.729 9 1.72 12 22.324 9
18 min -7.694 9 -25.153 9 0.478 1 -0.321 1 1.116 1
19 max B 25.851 9 7.574 9 9.138 9 2.221 1 23.018 9
20 min -3.986 3 -13.099 3 0.606 1 0.019 12 1.052 1
21 P124 max T 12.493 3 3.861 3 8.594 9 1.852 11 21.972 9
22 min -7.567 9 -24.755 9 0.428 5 -0.778 12 0.749 5
23 max B 25.407 9 7.399 9 9.004 9 1.908 1 22.634 9
24 min -3.752 3 -12.613 3 0.569 5 -0.396 12 1.249 5
25 P78 max T 12.738 7 3.959 7 8.537 1 2.257 5 21.879 1
26 min -7.588 1 -24.663 1 0.394 5 0.05 6 0.694 5
27 max B 25.286 1 7.348 1 8.969 1 1.72 6 22.529 1
28 min -3.866 7 -12.878 7 0.579 5 -0.507 5 1.393 5
29 P38 max T 12.19 7 3.715 7 8.504 1 2.077 4 21.706 1
30 min -7.439 1 -24.447 1 0.5 9 0.137 5 1.213 9
31 max B 25.175 1 7.39 1 8.893 1 1.936 5 22.413 1
32 min -3.737 7 -12.378 7 0.597 9 -0.197 4 1.037 9
33 P163 max T 11.106 11 3.944 11 7.683 5 2.057 9 20.96 5
34 min -8.51 5 -23.877 5 0.354 9 0.239 10 0.873 9
35 max B 24.898 5 8.828 5 8.035 5 1.874 10 21.864 5
36 min -4.037 11 -11.349 11 0.633 2 -0.045 9 1.295 9
37 P158 max T 10.82 11 3.894 11 7.573 5 1.744 8 20.769 5
38 min -8.531 5 -23.676 5 0.168 1 0.01 9 0.32 1
39 max B 24.524 5 8.638 5 7.943 5 1.725 9 21.545 5
40 min -3.899 11 -11 11 0.437 1 -0.392 8 0.763 1
41 P119 max T 23.46 9 8.381 9 7.54 9 1.879 2 20.592 9
42 min -3.521 3 -9.984 3 0.585 1 -0.164 1 1.055 1
43 max B 10.267 3 3.638 3 7.915 9 2.021 1 21.476 9
44 min -8.617 9 -24.447 9 0.538 1 0.238 2 1.356 1
45 P201 max T 10.72 11 3.35 11 7.94 5 1.812 9 20.383 5
46 min -7.104 5 -22.984 5 0.312 9 0.069 10 0.844 9
47 max B 23.572 5 6.846 5 8.363 5 1.7 10 21.003 5
48 min -3.267 11 -10.832 11 0.513 9 -0.158 9 1.274 2
49 P110 max T 23.082 9 8.279 9 7.401 9 1.74 1 20.254 9
50 min -3.459 3 -9.611 3 0.6 12 -0.495 12 1.664 12
51 max B 9.793 3 3.448 3 7.772 9 1.9 12 21.103 9
52 min -8.48 9 -24.024 9 0.296 12 0.002 1 0.864 12
53 P60 max T 22.931 1 8.236 1 7.348 1 1.9 6 20.12 1
54 min -3.507 7 -9.827 7 0.572 10 0.009 5 1.577 10
55 max B 10.027 7 3.507 7 7.73 1 1.946 5 20.941 1
56 min -8.37 1 -23.831 1 0.256 10 0.219 6 0.794 10
57 P188 max T 10.35 11 3.18 11 7.866 5 1.85 8 20.076 5
58 min -6.881 5 -22.612 5 0.111 1 0.201 9 0.241 1
59 max B 23.332 5 6.862 5 8.235 5 1.88 9 20.77 5
60 min -3.199 11 -10.532 11 0.289 1 -0.105 8 0.779 1


61 P56 max T 22.715 1 8.105 1 7.305 1 1.774 5 19.938 1
62 min -3.305 7 -9.295 7 0.506 9 -0.273 4 0.883 9
63 max B 9.566 7 3.413 7 7.669 1 1.712 4 20.854 1
64 min -8.409 1 -23.746 1 0.435 9 -0.013 5 1.08 9
65 P107 max T 22.396 9 6.714 9 7.841 9 1.72 2 19.907 9
66 min -2.78 3 -9.507 3 0.587 1 -0.519 1 1.559 1
67 max B 9.63 3 2.666 3 8.263 9 1.901 1 20.596 9
68 min -6.547 9 -23.074 9 0.578 1 0.085 2 1.366 1
69 P127 max T 21.972 9 6.545 9 7.714 9 1.921 1 19.54 9
70 min -2.546 3 -9.019 3 0.77 5 -0.188 12 1.35 12
71 max B 9.226 3 2.583 3 8.119 9 2.116 12 20.224 9
72 min -6.415 9 -22.653 9 0.348 12 0.143 1 0.778 12
73 P34 max T 21.807 1 6.483 1 7.662 1 1.739 6 19.396 1
74 min -2.659 7 -9.277 7 0.742 10 -0.267 5 1.285 10
75 max B 9.489 7 2.686 7 8.056 1 1.811 5 20.115 1
76 min -6.433 1 -22.545 1 0.311 10 0.067 6 0.673 10
77 P82 max T 21.708 1 6.522 1 7.593 1 1.962 5 19.292 1
78 min -2.536 7 -8.801 7 0.536 9 -0.041 4 1.32 9
79 max B 8.924 7 2.431 7 8.029 1 1.904 4 19.949 1
80 min -6.274 1 -22.331 1 0.485 9 0.124 5 1.074 9
81 P183 max T 21.039 5 7.564 5 6.738 5 1.87 10 18.459 5
82 min -2.729 11 -7.646 11 0.496 2 0.185 9 1.661 2
83 max B 7.819 11 2.735 11 7.11 5 2.046 2 19.239 5
84 min -7.671 5 -21.891 5 0.437 2 0.25 10 1.463 2
85 P174 max T 20.671 5 7.372 5 6.649 5 1.69 9 18.145 5
86 min -2.592 11 -7.29 11 0.638 8 -0.068 8 1.716 1
87 max B 7.541 11 2.683 11 6.999 5 1.647 47 19.046 5
88 min -7.69 5 -21.689 5 0.591 8 0.029 10 1.901 8
89 P171 max T 19.993 5 5.933 5 7.03 5 1.716 10 17.785 5
90 min -2.037 11 -7.2 11 0.681 2 -0.052 9 1.336 2
91 max B 7.372 11 2.052 11 7.405 5 1.797 2 18.489 5
92 min -5.912 5 -20.722 5 0.528 2 0.1 10 1.091 2
93 P191 max T 19.766 5 5.944 5 6.911 5 1.874 9 17.565 5
94 min -1.967 11 -6.889 11 0.653 1 0.103 8 1.72 8
95 max B 7.019 11 1.88 11 7.34 5 1.796 47 18.194 5
96 min -5.675 5 -20.355 5 0.695 8 0.171 10 1.485 8
97 P135 max T 7.767 3 0.596 5 7.924 9 0.954 5 15.474 9
98 min -0.737 12 -15.069 9 0.386 1 -0.684 6 0.686 1
99 max B 15.42 9 1.596 12 8.17 9 2.325 5 15.9 9
100 min -1.422 5 -7.819 3 0.831 5 -0.673 4 1.616 1
101 P121 max T 7.458 3 0.788 1 7.843 9 1.169 12 15.263 9
102 min -0.688 6 -14.801 9 0.154 5 -0.474 1 0.432 5
103 max B 15.169 9 1.589 6 8.119 9 1.209 1 15.731 9
104 min -1.54 1 -7.581 3 0.528 5 -0.587 12 1.107 5
105 P33 max T 7.33 7 0.846 5 7.774 1 1.141 4 15.129 1
106 min -0.834 10 -14.672 1 0.377 9 -0.479 5 0.653 9
107 max B 14.985 1 1.662 10 7.964 1 1.248 5 15.477 1
108 min -1.607 5 -7.387 7 0.863 9 -0.557 4 1.52 9
109 P76 max T 7.621 7 0.626 9 7.727 1 0.941 9 15.102 1
110 min -0.733 4 -14.723 1 0.123 5 -0.696 10 0.576 5
111 max B 15.13 1 1.527 4 8.061 1 1.046 10 15.649 1
112 min -1.347 9 -7.74 7 0.508 5 -0.749 9 1.195 5
113 P118 max T 13.35 9 1.706 12 7.47 9 0.983 6 14.211 9
114 min -0.84 5 -5.615 3 0.549 5 -0.785 5 1.629 1
115 max B 5.738 3 0.153 5 7.746 9 1.357 1 14.687 9


116 min -1.123 1 -13.722 9 0.053 1 -0.661 41 1.18 1
117 P91 max T 8.313 3 3.994 3 4.249 9 1.198 111 14.166 9
118 min -7.855 9 -16.353 9 0.037 6 -0.404 2 1.003 1
119 max B 16.582 9 7.974 9 4.304 9 1.23 2 14.364 9
120 min -3.959 3 -8.395 3 0.684 64 -0.61 1 1.724 1
121 P136 max T 13.103 9 1.608 6 7.419 9 1.171 1 14.052 9
122 min -0.86 1 -5.377 3 0.294 5 -0.536 12 1.443 5
123 max B 5.429 3 0.264 1 7.664 9 1.122 111 14.481 9
124 min -0.837 5 -13.45 9 0.386 5 -0.473 2 1.395 5
125 P199 max T 6.416 11 0.87 1 7.147 5 0.922 12 14.013 5
126 min -0.983 8 -13.713 5 0.09 9 -0.659 85 0.736 9
127 max B 14.12 5 1.249 8 7.49 5 1.013 2 14.569 5
128 min -1.185 1 -6.519 11 0.176 9 -0.745 1 0.927 9
129 P185 max T 6.234 11 1.094 9 7.19 5 1.12 47 14 5
130 min -1.007 2 -13.586 5 0.081 1 -0.46 10 0.428 1
131 max B 13.876 5 1.34 2 7.353 5 1.216 9 14.309 5
132 min -1.415 9 -6.29 11 0.269 1 -0.542 8 0.719 1
133 P90 max T 8.092 3 3.946 3 4.137 9 2.283 5 13.969 9
134 min -7.854 9 -16.128 9 0.16 5 -0.74 41 0.437 5
135 max B 16.332 9 8.016 9 4.177 7 1.037 5 14.145 9
136 min -4.049 3 -8.115 3 0.655 88 -0.779 4 1.556 5
137 P32 max T 13.044 1 1.603 4 7.356 1 1.001 10 13.953 1
138 min -0.728 9 -5.537 7 0.249 5 -0.712 9 1.665 5
139 max B 5.598 7 0.148 9 7.545 1 0.938 8 14.303 1
140 min -1.128 5 -13.358 1 0.385 5 -0.697 5 1.641 10
141 P9 max T 8.212 7 3.857 7 4.184 1 1.2 79 13.901 1
142 min -7.679 1 -16.047 1 0.317 5 -0.42 10 0.652 5
143 max B 16.224 1 7.91 1 4.157 1 1.243 6 14.052 1
144 min -3.947 7 -8.244 7 0.597 32 -0.558 5 1.76 5
145 P8 max T 7.896 7 3.938 7 4.069 1 1.628 9 13.785 1
146 min -7.779 1 -15.916 1 0.013 9 -0.736 117 0.955 9
147 max B 16.172 1 7.829 1 4.172 1 1.092 9 14.008 1
148 min -3.918 7 -7.97 7 0.631 9 -0.765 8 1.535 9
149 P77 max T 12.9 1 1.701 10 7.259 1 1.206 5 13.78 1
150 min -0.961 5 -5.188 7 0.585 9 -0.518 4 1.462 9
151 max B 5.304 7 0.357 5 7.592 1 1.123 79 14.338 1
152 min -0.959 10 -13.306 1 0.053 9 -0.668 9 0.961 9
153 P70 max T 7.81 3 3.776 3 3.975 9 1.84 6 13.342 9
154 min -7.453 9 -15.404 9 0.344 1 0.111 2 1.183 1
155 max B 15.595 9 7.465 9 4.065 9 1.788 2 13.51 9
156 min -3.752 3 -7.868 3 0.678 88 -0.678 1 1.73 1
157 P97 max T 7.666 3 3.703 3 3.93 9 1.935 6 13.219 9
158 min -7.402 9 -15.262 9 0.17 5 0.272 2 0.498 5
159 max B 15.444 9 7.434 9 4.005 9 2.166 1 13.378 9
160 min -3.738 3 -7.703 3 0.648 88 -0.449 12 1.355 5
161 P13 max T 7.693 7 3.685 7 3.913 1 1.966 10 13.1 1
162 min -7.297 1 -15.124 1 0.141 5 0.095 6 0.487 5
163 max B 15.296 1 7.358 1 3.969 1 1.808 6 13.25 1
164 min -3.714 7 -7.732 7 0.621 32 -0.54 5 1.46 5
165 P133 max T 5.506 3 0.4 5 7.279 9 1.293 5 13.07 9
166 min -0.011 12 -10.726 9 0.729 1 -0.777 6 1.342 1
167 max B 10.932 9 0.193 12 7.385 9 1.139 12 13.274 9
168 min -0.598 5 -5.525 3 0.758 5 -0.673 1 1.489 1
169 P12 max T 7.504 7 3.657 7 3.866 1 1.959 10 13.038 1
170 min -7.321 1 -15.053 1 0.342 9 0.254 6 1.143 9


171 max B 15.254 1 7.305 1 3.975 1 2.212 5 13.215 1
172 min -3.641 7 -7.557 7 0.685 9 -0.352 4 1.586 9
173 P111 max T 5.285 3 0.341 1 7.234 9 1.325 12 12.959 9
174 min -0.113 5 -10.541 9 0.378 5 -0.772 1 0.819 5
175 max B 10.765 9 -0.025 5 7.353 9 1.188 5 13.185 9
176 min -0.508 1 -5.371 3 0.43 5 -0.657 6 0.848 5
177 P155 max T 6.906 11 3.257 11 3.919 5 1.198 39 12.951 5
178 min -7.109 5 -14.948 5 0.4 2 -0.55 2 0.978 9
179 max B 15.108 5 7.359 5 3.874 5 1.225 10 13.086 5
180 min -3.337 11 -6.931 11 0.675 108 -0.513 9 1.517 9
181 P182 max T 11.971 5 1.458 9 6.775 5 0.967 2 12.833 5
182 min -0.563 1 -4.287 11 0.241 9 -0.687 1 1.643 1
183 max B 4.341 11 0.393 1 6.937 5 0.935 12 13.143 5
184 min -1.289 9 -12.262 5 0.436 9 -0.785 9 1.846 1
185 P41 max T 5.202 7 0.515 5 7.143 1 2.306 5 12.806 1
186 min -0.046 10 -10.452 1 0.658 9 -0.607 6 1.188 9
187 max B 10.624 1 0.222 10 7.223 1 1.115 9 12.964 1
188 min -0.697 5 -5.227 7 0.773 9 -0.679 10 1.365 9
189 P71 max T 5.394 7 0.26 9 7.124 1 2.291 10 12.787 1
190 min -0.178 5 -10.475 1 0.465 5 -0.608 11 1.03 5
191 max B 10.734 1 0.087 5 7.27 1 2.356 5 13.06 1
192 min -0.42 9 -5.475 7 0.475 5 -0.518 8 0.996 5
193 P154 max T 6.694 11 3.322 11 3.744 5 1.046 8 12.755 5
194 min -7.239 5 -14.727 5 0.346 1 -0.741 81 0.697 1
195 max B 14.986 5 7.262 5 3.862 5 0.997 1 12.98 5
196 min -3.306 11 -6.765 11 0.64 1 -0.749 12 1.168 1
197 P101 max T 14.648 9 7.01 9 3.819 9 1.227 2 12.69 9
198 min -2.902 3 -6.221 3 0.731 6 -0.557 1 1.651 1
199 max B 6.241 3 3.006 3 3.845 9 1.236 111 12.871 9
200 min -7.169 9 -14.859 9 0.189 6 -0.69 6 0.936 1
201 P200 max T 11.728 5 1.353 2 6.637 5 1.153 9 12.573 5
202 min -0.744 9 -4.056 11 0.104 1 -0.494 8 1.334 1
203 max B 4.161 11 0.586 9 6.98 5 1.288 1 13.143 5
204 min -1.101 2 -12.134 5 0.262 1 -0.471 10 1.41 1
205 P93 max T 14.405 9 7.049 9 3.824 7 2.355 4 12.476 9
206 min -2.994 3 -5.938 3 0.73 86 -0.73 3 1.789 5
207 max B 6.021 3 2.959 3 3.728 9 0.981 12 12.668 9
208 min -7.171 9 -14.626 9 0.42 12 -0.78 41 1.075 5
209 P113 max T 9.564 9 0.312 12 7.03 9 2.247 1 12.438 9
210 min -0.246 5 -4.497 9 0.546 5 -0.59 4 1.235 5
211 max B 4.513 9 0.057 5 7.151 9 1.18 5 12.663 9
212 min -0.444 1 -9.789 9 0.682 1 -0.737 6 1.631 1
213 P143 max T 9.401 9 0.45 5 7.003 9 1.51 5 12.364 9
214 min -0.089 1 -4.605 9 0.527 5 -0.688 6 1.338 5
215 max B 4.61 9 -0.086 1 7.108 9 1.256 12 12.561 9
216 min -0.604 5 -9.605 9 0.471 5 -0.674 1 1.349 5
217 P55 max T 14.275 1 6.938 1 3.668 1 1.248 6 12.364 1
218 min -2.894 7 -6.067 7 0.672 32 -0.527 5 2.033 5
219 max B 6.149 7 2.87 7 3.772 1 1.24 79 12.588 1
220 min -6.987 1 -14.532 1 0.476 10 -0.521 10 1.43 5
221 P54 max T 14.227 1 6.853 1 3.687 1 1.033 9 12.324 1
222 min -2.861 7 -5.801 7 0.725 4 -0.764 8 1.422 9
223 max B 5.825 7 2.954 7 3.658 1 1.094 4 12.473 1
224 min -7.085 1 -14.402 1 0.279 4 -0.775 117 0.701 9
225 P27 max T 9.355 1 0.577 5 6.914 1 2.052 5 12.221 1


226 min -0.036 9 -4.472 1 0.621 5 -0.592 6 1.61 5
227 max B 4.462 1 -0.132 9 6.995 1 2.344 10 12.377 1
228 min -0.731 5 -9.528 1 0.552 5 -0.617 11 1.599 5
229 P149 max T 6.477 11 3.105 11 3.647 5 2.099 2 12.188 5
230 min -6.777 5 -14.071 5 0.229 9 0.03 1 0.437 9
231 max B 14.233 5 6.847 5 3.693 5 1.782 10 12.329 5
232 min -3.132 11 -6.51 11 0.607 9 -0.489 9 1.071 9
233 P85 max T 9.247 1 0.289 10 6.869 1 1.332 9 12.132 1
234 min -0.309 5 -4.491 1 0.711 5 -0.718 10 1.599 5
235 max B 4.521 1 0.14 5 7.013 1 1.205 4 12.4 1
236 min -0.343 9 -9.505 1 0.607 9 -0.725 5 1.417 9
237 P161 max T 6.352 11 3.094 11 3.575 5 2.011 2 12.079 5
238 min -6.797 5 -13.947 5 0.18 1 -0.258 1 0.496 1
239 max B 14.145 5 6.77 5 3.687 5 2.188 9 12.254 5
240 min -3.079 11 -6.403 11 0.495 1 -0.296 8 0.949 1
241 P130 max T 13.798 9 6.669 9 3.565 9 1.789 2 11.952 9
242 min -2.784 3 -5.829 3 0.638 1 -0.508 1 1.129 1
243 max B 5.863 3 2.821 3 3.643 9 2.003 6 12.113 9
244 min -6.698 9 -13.983 9 0.208 1 0.051 5 0.386 1
245 P175 max T 4.419 11 0.638 9 6.598 5 2.247 9 11.836 5
246 min -0.086 1 -9.68 5 0.357 1 -0.615 10 0.761 1
247 max B 9.833 5 0.101 1 6.666 5 1.292 1 11.973 5
248 min -0.719 9 -4.444 11 0.317 1 -0.672 2 0.69 1
249 P197 max T 4.538 11 0.484 1 6.584 5 2.35 2 11.836 5
250 min -0.282 9 -9.751 5 0.378 9 -0.6 3 0.93 9
251 max B 10.014 5 0.352 9 6.734 5 2.106 9 12.116 5
252 min -0.557 1 -4.608 11 0.281 9 -0.508 10 0.798 9
253 P72 max T 13.65 9 6.635 9 3.507 9 2.202 1 11.823 9
254 min -2.771 3 -5.662 3 0.677 5 -0.356 12 1.201 5
255 max B 5.719 3 2.748 3 3.594 9 2.09 5 11.987 9
256 min -6.65 9 -13.838 9 0.189 5 0.273 2 0.491 5
257 P59 max T 13.483 1 6.554 1 3.465 1 1.821 6 11.678 1
258 min -2.751 7 -5.693 7 0.677 32 -0.376 5 1.298 5
259 max B 5.752 7 2.73 7 3.575 1 2.168 10 11.856 1
260 min -6.536 1 -13.686 1 0.315 5 0.04 9 0.69 5
261 P57 max T 13.444 1 6.499 1 3.472 1 2.268 5 11.645 1
262 min -2.674 7 -5.523 7 0.567 9 -0.254 4 1.016 9
263 max B 5.56 7 2.705 7 3.528 1 2.007 10 11.794 1
264 min -6.56 1 -13.616 1 0.136 9 -0.505 9 0.29 9
265 P165 max T 13.091 5 6.356 5 3.367 5 1.223 10 11.338 5
266 min -2.265 11 -4.724 11 0.614 2 -0.486 9 1.908 1
267 max B 4.791 11 2.251 11 3.487 5 1.263 3 11.566 5
268 min -6.378 5 -13.351 5 0.549 2 -0.605 2 1.828 1
269 P177 max T 8.591 5 0.714 9 6.37 5 1.827 9 11.255 5
270 min -0.186 1 -4.15 5 0.572 1 -0.608 10 1.247 1
271 max B 4.135 5 0.126 1 6.44 5 1.18 1 11.391 5
272 min -0.797 9 -8.746 5 0.521 9 -0.746 2 1.361 1
273 P157 max T 12.973 5 6.255 5 3.359 5 0.963 1 11.238 5
274 min -2.235 11 -4.555 11 0.511 8 -0.742 12 1.497 1
275 max B 4.584 11 2.312 11 3.314 5 2.354 7 11.373 5
276 min -6.505 5 -13.132 5 0.506 8 -0.781 81 1.399 1
277 P105 max T 6.432 3 2.339 3 4.079 9 2.113 3 11.202 9
278 min -4.615 9 -12.772 9 0.678 88 -0.693 5 1.654 1
279 max B 12.646 9 4.723 9 3.961 9 2.241 11 11.068 9
280 min -2.352 3 -6.431 3 0.648 64 -0.718 12 1.81 1


281 P207 max T 8.414 5 0.529 1 6.306 5 1.653 1 11.124 5
282 min -0.323 9 -4.198 5 0.496 1 -0.706 2 1.338 1
283 max B 4.233 5 0.275 9 6.454 5 1.189 8 11.398 5
284 min -0.627 1 -8.675 5 0.432 1 -0.762 9 1.296 1
285 P103 max T 6.337 3 2.346 3 4.018 9 2.257 5 11.1 9
286 min -4.629 9 -12.665 9 0.564 5 -0.333 6 1.119 5
287 max B 12.513 9 4.749 9 3.882 9 2.35 12 10.941 9
288 min -2.388 3 -6.272 3 0.61 88 -0.367 1 1.44 5
289 P17 max T 6.356 7 2.281 7 4.012 1 2.118 7 11.017 1
290 min -4.536 1 -12.56 1 0.639 32 -0.751 9 1.39 5
291 max B 12.382 1 4.668 1 3.857 1 2.232 3 10.83 1
292 min -2.321 7 -6.299 7 0.576 32 -0.741 4 1.686 32
293 P16 max T 6.185 7 2.317 7 3.958 1 2.115 9 10.934 1
294 min -4.56 1 -12.476 1 0.627 9 -0.367 10 1.46 9
295 max B 12.376 1 4.657 1 3.859 1 2.273 4 10.827 1
296 min -2.335 7 -6.173 7 0.668 32 -0.407 5 1.58 9
297 P194 max T 12.356 5 6.01 5 3.173 5 1.782 10 10.702 5
298 min -2.149 11 -4.441 11 0.561 1 -0.266 9 1.198 9
299 max B 4.49 11 2.134 11 3.287 5 2.238 2 10.878 5
300 min -5.982 5 -12.556 5 0.507 1 -0.153 1 1.18 9
301 P150 max T 12.27 5 5.931 5 3.17 5 2.256 9 10.628 5
302 min -2.097 11 -4.331 11 0.459 1 -0.157 8 0.883 1
303 max B 4.368 11 2.121 11 3.216 5 2.285 1 10.769 5
304 min -6.001 5 -12.433 5 0.397 1 0.291 11 0.809 1
305 P106 max T 5.639 3 0.749 3 4.894 9 2.028 3 10.608 9
306 min -1.483 9 -11.271 9 0.71 5 -0.748 5 1.375 5
307 max B 11.001 9 1.503 9 4.749 9 2.342 12 10.332 9
308 min -0.754 3 -5.589 3 0.767 88 0.032 1 1.61 5
309 P95 max T 5.623 3 0.756 3 4.879 9 2.035 5 10.581 9
310 min -1.489 9 -11.246 9 0.598 5 -0.24 6 1.179 5
311 max B 10.962 9 1.509 9 4.726 9 2.039 12 10.291 9
312 min -0.761 3 -5.538 3 0.601 5 -0.275 1 1.138 5
313 P21 max T 5.556 7 0.735 7 4.819 1 2.304 9 10.446 1
314 min -1.462 1 -11.1 1 0.717 5 0.058 10 1.395 5
315 max B 10.8 1 1.481 1 4.66 1 2.304 4 10.141 1
316 min -0.739 7 -5.476 7 0.722 5 -0.103 5 1.359 5
317 P20 max T 5.505 7 0.742 7 4.801 1 1.92 9 10.412 1
318 min -1.463 1 -11.066 1 0.779 9 -0.289 10 1.61 9
319 max B 10.81 1 1.484 1 4.663 1 1.968 4 10.149 1
320 min -0.748 7 -5.449 7 0.754 9 -0.346 5 1.524 9
321 P169 max T 5.354 11 1.93 11 3.746 5 2.114 11 10.261 5
322 min -4.204 5 -11.696 5 0.694 108 -0.694 1 1.382 9
323 max B 11.512 5 4.336 5 3.588 5 2.235 7 10.07 5
324 min -1.964 11 -5.303 11 0.636 108 -0.738 8 1.578 9
325 P167 max T 5.238 11 1.953 11 3.661 5 2.334 1 10.131 5
326 min -4.239 5 -11.562 5 0.6 1 -0.351 2 1.142 1
327 max B 11.475 5 4.329 5 3.573 5 2.249 8 10.037 5
328 min -1.971 11 -5.229 11 0.662 132 -0.432 9 1.298 1
329 P132 max T 11.452 9 4.117 9 3.668 9 2.221 11 10.048 9
330 min -1.713 3 -4.817 3 0.768 88 -0.749 12 1.605 1
331 max B 4.754 3 1.754 3 3.538 9 2.129 3 9.896 9
332 min -4.233 9 -11.309 9 0.725 88 -0.588 5 1.393 1
333 P120 max T 11.328 9 4.139 9 3.594 9 2.289 12 9.928 9
334 min -1.746 3 -4.661 3 0.735 88 -0.429 1 1.483 5
335 max B 4.657 3 1.763 3 3.471 9 1.506 3 9.787 9


336 min -4.251 9 -11.194 9 0.662 5 -0.666 5 1.149 5
337 P138 max T 5.628 3 1.197 3 4.357 9 2.279 115 9.808 9
338 min -1.909 9 -10.622 9 0.101 1 -0.505 6 0.321 1
339 max B 10.955 9 2.056 12 4.679 9 2.25 2 10.25 9
340 min -1.351 5 -5.666 3 0.68 1 -0.556 1 1.245 1
341 P63 max T 11.178 1 4.055 1 3.562 1 2.212 3 9.802 1
342 min -1.682 7 -4.687 7 0.701 32 -0.769 4 1.759 5
343 max B 4.683 7 1.698 7 3.466 1 2.137 7 9.697 1
344 min -4.15 1 -11.082 1 0.677 32 -0.668 9 1.479 5
345 P49 max T 11.175 1 4.044 1 3.565 1 2.217 4 9.8 1
346 min -1.695 7 -4.568 7 0.768 9 -0.484 5 1.36 9
347 max B 4.505 7 1.735 7 3.408 1 2.355 9 9.612 1
348 min -4.177 1 -10.993 1 0.645 9 -0.386 10 1.163 9
349 P170 max T 4.691 11 0.622 11 4.483 5 2.027 11 9.716 5
350 min -1.357 5 -10.323 5 0.644 9 -0.748 1 1.202 9
351 max B 10.027 5 1.374 5 4.326 5 2.309 8 9.415 5
352 min -0.626 11 -4.618 11 0.661 9 -0.156 9 1.213 9
353 P159 max T 4.654 11 0.626 11 4.457 5 2.073 1 9.665 5
354 min -1.359 5 -10.273 5 0.567 1 -0.265 2 1.101 1
355 max B 10.031 5 1.381 5 4.325 5 1.963 8 9.417 5
356 min -0.632 11 -4.605 11 0.579 1 -0.392 9 1.102 1
357 P123 max T 5.339 3 1.236 1 4.293 9 1.426 6 9.61 9
358 min -1.934 7 -10.381 9 0.217 5 -0.195 2 0.562 5
359 max B 10.738 9 2.353 7 4.648 9 1.683 1 10.094 9
360 min -1.713 1 -5.467 3 0.509 5 -0.614 12 1.043 5
361 P37 max T 5.263 7 1.153 5 4.278 1 1.444 10 9.564 1
362 min -1.896 11 -10.324 1 0.074 9 -0.643 9 0.191 9
363 max B 10.608 1 2.321 11 4.544 1 1.774 5 9.936 1
364 min -1.589 5 -5.308 7 0.635 9 -0.553 4 1.132 9
365 P79 max T 5.513 7 1.253 7 4.224 1 2.285 11 9.543 1
366 min -1.902 1 -10.351 1 0.226 5 -0.232 10 0.72 5
367 max B 10.757 1 2.141 4 4.636 1 2.255 6 10.096 1
368 min -1.5 9 -5.634 7 0.522 5 -0.407 5 1.169 5
369 P129 max T 10.11 9 1.321 9 4.394 9 2.308 12 9.519 9
370 min -0.549 3 -4.212 3 0.598 5 -0.168 1 1.075 5
371 max B 4.128 3 0.553 3 4.245 9 2.037 3 9.233 9
372 min -1.341 9 -9.83 9 0.534 5 -0.56 5 0.954 5
373 P126 max T 10.076 9 1.327 9 4.374 9 1.993 12 9.482 9
374 min -0.554 3 -4.162 3 0.511 5 -0.398 1 0.887 5
375 max B 4.111 3 0.561 3 4.227 9 2.317 5 9.202 9
376 min -1.348 9 -9.801 9 0.492 5 -0.256 6 0.862 5
377 P66 max T 9.911 1 1.301 1 4.305 1 1.939 4 9.329 1
378 min -0.542 7 -4.077 7 0.556 9 -0.519 5 1.025 9
379 max B 3.993 7 0.547 7 4.145 1 2.125 9 9.023 1
380 min -1.32 1 -9.61 1 0.568 9 -0.301 10 1.069 9
381 P58 max T 9.9 1 1.297 1 4.301 1 2.277 4 9.319 1
382 min -0.534 7 -4.101 7 0.626 5 -0.352 5 1.088 5
383 max B 4.049 7 0.539 7 4.164 1 2.041 7 9.059 1
384 min -1.318 1 -9.645 1 0.611 5 -0.711 9 1.068 5
385 P134 max T 6.08 9 0.057 6 5.169 9 2.348 7 8.998 9
386 min -0.102 1 -4.257 9 0.372 1 -0.775 54 0.801 1
387 max B 4.723 9 -0.343 6 5.439 9 0.914 6 9.447 9
388 min -0.071 1 -6.154 9 0.149 1 -0.753 5 0.338 1
389 P196 max T 10.245 5 3.706 5 3.27 5 2.215 7 8.985 5
390 min -1.316 11 -3.659 11 0.752 108 -0.767 8 1.563 1


391 max B 3.65 11 1.331 11 3.186 5 2.135 11 8.896 5
392 min -3.792 5 -10.164 5 0.729 108 -0.589 1 1.492 1
393 P184 max T 10.212 5 3.697 5 3.258 5 2.191 8 8.956 5
394 min -1.322 11 -3.585 11 0.766 1 -0.532 9 1.337 1
395 max B 3.534 11 1.358 11 3.097 5 1.509 11 8.761 5
396 min -3.831 5 -10.024 5 0.738 1 -0.607 1 1.29 1
397 P202 max T 4.672 11 1.121 11 3.905 5 2.298 3 8.882 5
398 min -1.853 5 -9.662 5 0.226 9 -0.465 2 0.834 9
399 max B 10.071 5 1.905 8 4.322 5 2.236 10 9.439 5
400 min -1.233 1 -4.775 11 0.32 9 -0.131 9 0.988 9
401 P109 max T 6.031 9 0.201 12 5.094 9 1.621 12 8.872 9
402 min -0.169 5 -4.157 9 0.268 5 -0.656 1 0.636 5
403 max B 4.658 9 0.055 12 5.358 9 1.047 1 9.306 9
404 min -0.141 5 -6.057 9 0.15 12 -0.677 12 0.332 12
405 P187 max T 4.516 11 1.255 9 3.96 5 2.001 1 8.863 5
406 min -1.992 3 -9.573 5 0.131 1 -0.179 11 0.497 1
407 max B 9.83 5 2.072 3 4.197 5 1.711 9 9.197 5
408 min -1.417 9 -4.562 11 0.281 1 -0.581 8 0.708 1
409 P75 max T 6.006 1 0.189 10 5.059 1 2.338 11 8.813 1
410 min -0.156 5 -4.112 1 0.279 5 -0.78 130 0.651 5
411 max B 4.68 1 0.011 10 5.333 1 0.958 10 9.26 1
412 min -0.083 5 -5.986 1 0.18 10 -0.733 9 0.366 10
413 P24 max T 5.907 1 0.084 4 5.035 1 1.44 4 8.764 1
414 min -0.073 9 -4.162 1 0.364 9 -0.686 5 0.767 9
415 max B 4.564 1 -0.263 4 5.296 1 1.05 5 9.202 1
416 min -0.03 9 -6.027 1 0.181 9 -0.568 4 0.377 9
417 P89 max T 9.107 9 2.255 12 4.031 9 2.337 2 8.633 9
418 min -0.84 5 -3.723 3 0.397 5 -0.361 1 1.415 5
419 max B 3.86 3 0.392 5 4.394 9 2.335 7 9.151 9
420 min -1.61 12 -9.475 9 0.402 1 -0.529 6 1.204 6
421 P190 max T 9.073 5 1.19 5 3.941 5 1.934 8 8.54 5
422 min -0.423 11 -3.196 11 0.485 1 -0.619 9 0.841 1
423 max B 3.124 11 0.428 11 3.783 5 1.589 11 8.237 5
424 min -1.209 5 -8.775 5 0.49 1 -0.75 1 0.85 1
425 P193 max T 9.066 5 1.185 5 3.941 5 2.281 8 8.536 5
426 min -0.418 11 -3.21 11 0.538 1 -0.436 9 0.952 1
427 max B 3.16 11 0.422 11 3.811 5 2.039 11 8.29 5
428 min -1.205 5 -8.827 5 0.526 1 -0.542 1 0.933 1
429 P92 max T 4.429 9 0.062 1 4.897 9 2.04 1 8.494 9
430 min -0.032 6 -5.365 9 0.429 1 -0.664 2 0.891 1
431 max B 5.362 9 0.106 1 5.208 9 1.798 1 9.022 9
432 min 0.096 6 -5.054 9 0.037 1 -0.639 111 0.157 1
433 P140 max T 8.895 9 2.356 6 4.003 9 1.635 1 8.485 9
434 min -1.117 1 -3.536 3 0.565 5 -0.575 12 1.605 5
435 max B 3.574 3 0.657 1 4.333 9 1.589 5 8.963 9
436 min -1.625 6 -9.233 9 0.454 12 -0.286 2 1.118 12
437 P35 max T 8.897 1 2.317 4 3.986 1 2.349 6 8.473 1
438 min -0.955 9 -3.695 7 0.57 9 -0.201 5 1.675 32
439 max B 3.744 7 0.508 9 4.258 1 2.349 11 8.87 1
440 min -1.687 4 -9.187 1 0.497 10 -0.347 10 1.233 10
441 P74 max T 4.32 9 0.138 5 4.822 9 1.668 5 8.367 9
442 min -0.178 12 -5.323 9 0.332 5 -0.714 6 0.744 5
443 max B 5.268 9 -0.024 5 5.119 9 1.12 5 8.867 9
444 min -0.156 12 -4.97 9 0.061 12 -0.647 4 0.242 12
445 P10 max T 4.286 1 0.13 5 4.802 1 1.71 5 8.333 1


446 min -0.17 10 -5.318 1 0.349 5 -0.672 6 0.771 5
447 max B 5.199 1 -0.121 5 5.093 1 0.967 6 8.823 1
448 min -0.164 10 -4.988 1 0.036 10 -0.698 5 0.209 10
449 P81 max T 8.748 1 2.282 10 3.894 1 1.763 5 8.31 1
450 min -1.029 5 -3.377 7 0.513 5 -0.522 4 1.491 9
451 max B 3.507 7 0.617 5 4.317 1 1.836 9 8.911 1
452 min -1.646 10 -9.165 1 0.332 9 -0.297 6 1.14 9
453 P7 max T 4.312 1 0.031 9 4.757 1 1.372 9 8.251 1
454 min -0.065 4 -5.202 1 0.416 9 -0.724 10 0.847 9
455 max B 5.263 1 0.085 9 5.075 1 2.073 9 8.792 1
456 min 0.039 4 -4.887 1 0.061 9 -0.638 8 0.181 9
457 P198 max T 5.59 5 0.017 2 4.703 5 2.045 2 8.194 5
458 min -0.019 9 -3.816 5 0.211 9 -0.783 3 0.431 9
459 max B 4.39 5 -0.325 2 4.97 5 0.883 85 8.628 5
460 min 0.184 9 -5.551 5 0.293 9 -0.709 12 0.519 9
461 P116 max T 3.69 9 -0.124 1 4.674 9 2.354 5 8.155 9
462 min 0.056 1 -5.659 9 0.09 1 -0.752 3 0.159 1
463 max B 5.695 9 -0.085 6 4.94 9 2.122 6 8.59 9
464 min 0.061 1 -4.186 9 0.434 1 -0.77 7 0.839 1
465 P173 max T 5.448 5 -0.038 8 4.654 5 1.371 8 8.099 5
466 min -0.078 1 -3.859 5 0.137 1 -0.66 9 0.32 1
467 max B 4.226 5 -0.226 1 4.905 5 1.034 10 8.523 5
468 min 0.038 1 -5.585 5 0.132 1 -0.557 47 0.248 1
469 P146 max T 3.521 9 0.14 5 4.627 9 2.122 6 8.091 9
470 min 0.131 1 -5.734 9 0.683 1 -0.746 7 1.306 1
471 max B 5.823 9 -0.191 1 4.662 9 2.176 1 8.158 9
472 min -0.129 5 -3.501 9 0.604 1 -0.579 2 1.124 1
473 P122 max T 3.601 9 0.062 1 4.604 9 2.271 1 8.036 9
474 min -0.031 5 -5.606 9 0.455 5 -0.552 2 0.927 5
475 max B 5.705 9 -0.006 5 4.64 9 1.56 5 8.107 9
476 min -0.037 1 -3.576 9 0.354 5 -0.694 6 0.705 5
477 P108 max T 3.625 9 -0.42 5 4.601 9 1.093 2 8.029 9
478 min 0.11 5 -5.578 9 0.265 5 -0.53 111 0.484 5
479 max B 5.63 9 0.068 12 4.857 9 1.561 12 8.448 9
480 min 0.2 5 -4.085 9 0.375 12 -0.619 1 0.787 12
481 P31 max T 3.638 1 -0.43 5 4.564 1 0.897 5 7.959 1
482 min 0.251 10 -5.49 1 0.341 5 -0.774 8 0.597 5
483 max B 5.61 1 0.067 10 4.823 1 1.888 10 8.39 1
484 min 0.304 5 -4.035 1 0.373 10 -0.779 11 0.781 10
485 P88 max T 3.48 1 0.038 9 4.537 1 2.046 10 7.93 1
486 min -0.052 5 -5.595 1 0.564 5 -0.764 11 1.155 5
487 max B 5.709 1 0.029 5 4.582 1 1.995 5 8.015 1
488 min -0.015 9 -3.454 1 0.447 5 -0.572 6 0.908 5
489 P36 max T 3.506 1 0.171 5 4.537 1 2.186 5 7.926 1
490 min 0.15 9 -5.568 1 0.595 9 -0.561 6 1.123 9
491 max B 5.643 1 -0.217 9 4.565 1 1.391 9 7.979 1
492 min -0.158 5 -3.486 1 0.534 9 -0.737 10 0.978 9
493 P68 max T 3.527 1 -0.09 9 4.533 1 1.107 6 7.916 1
494 min -0.022 9 -5.54 1 0.034 9 -0.752 9 0.082 9
495 max B 5.508 1 -0.073 4 4.797 1 1.354 4 8.339 1
496 min 0.014 9 -4.087 1 0.371 9 -0.646 5 0.736 9
497 P114 max T 4.941 9 0.056 1 4.501 9 1.955 1 7.808 9
498 min -0.01 5 -4.061 9 0.484 5 -0.742 2 0.973 5
499 max B 4.037 9 -0.016 5 4.536 9 2.155 6 7.873 9
500 min -0.131 1 -5.036 9 0.55 5 -0.773 7 1.092 5


501 P139 max T 4.83 9 0.142 5 4.489 9 1.768 5 7.782 9
502 min 0.123 1 -4.148 9 0.671 5 -0.729 6 1.419 5
503 max B 4.12 9 -0.165 1 4.519 9 1.517 12 7.837 9
504 min -0.199 5 -4.917 9 0.665 5 -0.718 1 1.439 5
505 P153 max T 8.157 5 2.084 8 3.671 5 2.317 12 7.781 5
506 min -0.683 1 -2.813 11 0.42 1 -0.784 10 1.321 1
507 max B 2.859 11 0.556 1 3.912 5 2.286 39 8.139 5
508 min -1.851 8 -8.42 5 0.556 1 -0.78 3 1.471 1
509 P156 max T 3.973 5 0.001 9 4.47 5 1.445 9 7.759 5
510 min -0.032 2 -4.967 5 0.286 9 -0.662 10 0.572 9
511 max B 4.826 5 -0.18 2 4.748 5 2.313 2 8.225 5
512 min 0.175 2 -4.671 5 0.178 2 -0.638 39 0.308 2
513 P44 max T 4.821 1 0.18 5 4.422 1 1.825 5 7.669 1
514 min 0.137 9 -4.022 1 0.681 9 -0.748 6 1.298 9
515 max B 4.002 1 -0.167 10 4.448 1 2.351 11 7.716 1
516 min -0.236 5 -4.893 1 0.744 9 -0.685 12 1.408 9
517 P80 max T 4.759 1 0.025 9 4.409 1 1.631 9 7.645 1
518 min -0.03 5 -4.06 1 0.619 5 -0.78 10 1.253 5
519 max B 4.029 1 0.002 5 4.449 1 2.324 5 7.717 1
520 min -0.099 9 -4.868 1 0.669 5 -0.393 6 1.339 5
521 P152 max T 3.982 5 0.048 1 4.394 5 1.758 1 7.621 5
522 min 0.017 8 -4.805 5 0.207 1 -0.691 2 0.439 1
523 max B 4.889 5 -0.198 1 4.705 5 1.137 8 8.152 5
524 min 0.195 1 -4.521 5 0.197 1 -0.633 9 0.34 1
525 P125 max T 4.816 9 -0.126 1 4.387 9 0.956 2 7.611 9
526 min 0.327 1 -3.959 9 0.227 1 -0.768 6 0.405 1
527 max B 4.612 9 -0.017 1 4.693 9 1.312 1 8.129 9
528 min 0.098 6 -4.774 9 0.383 1 -0.651 2 0.758 1
529 P204 max T 7.916 5 2.069 2 3.544 5 1.655 9 7.537 5
530 min -0.834 9 -2.602 11 0.422 1 -0.542 8 1.468 1
531 max B 2.718 11 0.717 9 3.976 5 1.793 1 8.152 5
532 min -1.778 2 -8.338 5 0.441 1 -0.301 12 1.493 1
533 P128 max T 4.734 9 -0.137 12 4.306 9 1.311 12 7.47 9
534 min 0.228 12 -3.877 9 0.183 12 -0.652 4 0.32 12
535 max B 4.5 9 -0.119 5 4.61 9 2.246 5 7.985 9
536 min -0.08 12 -4.72 9 0.372 12 -0.694 6 0.787 12
537 P46 max T 4.651 1 -0.112 10 4.269 1 2.082 10 7.405 1
538 min 0.248 10 -3.887 1 0.18 10 -0.668 79 0.319 10
539 max B 4.464 1 -0.232 5 4.59 1 1.172 5 7.951 1
540 min -0.08 10 -4.716 1 0.362 10 -0.662 6 0.767 10
541 P53 max T 4.72 1 -0.043 9 4.254 1 1.137 4 7.384 1
542 min 0.285 9 -3.789 1 0.164 9 -0.641 5 0.308 9
543 max B 4.491 1 0.029 9 4.544 1 2.098 9 7.871 1
544 min 0.069 4 -4.598 1 0.317 9 -0.698 10 0.649 9
545 P210 max T 3.164 5 0.152 1 4.196 5 2.092 2 7.34 5
546 min -0.09 9 -5.227 5 0.492 9 -0.753 3 1.032 9
547 max B 5.343 5 0.106 9 4.241 5 1.843 9 7.428 5
548 min -0.142 1 -3.139 5 0.39 9 -0.561 10 0.837 9
549 P186 max T 3.216 5 0.209 9 4.189 5 2.129 9 7.321 5
550 min -0.023 1 -5.163 5 0.408 1 -0.581 10 0.827 1
551 max B 5.23 5 0.029 1 4.214 5 1.625 1 7.369 5
552 min -0.203 9 -3.198 5 0.326 1 -0.721 2 0.667 1
553 P180 max T 3.339 5 -0.425 9 4.188 5 0.99 9 7.303 5
554 min 0.176 2 -5.036 5 0.481 2 -0.771 12 0.863 9
555 max B 5.173 5 -0.12 2 4.437 5 2.136 2 7.72 5


556 min 0.571 9 -3.7 5 0.372 2 -0.757 3 0.692 2
557 P172 max T 3.18 5 -0.277 1 4.13 5 1.095 10 7.216 5
558 min 0.231 8 -5.08 5 0.33 1 -0.685 1 0.574 1
559 max B 5.028 5 -0.21 8 4.386 5 1.251 8 7.624 5
560 min 0.376 1 -3.744 5 0.444 8 -0.602 9 0.803 8
561 P178 max T 4.421 5 0.224 9 4.075 5 1.738 9 7.066 5
562 min -0.019 1 -3.728 5 0.471 1 -0.779 10 0.951 1
563 max B 3.71 5 -0.005 1 4.098 5 2.127 2 7.108 5
564 min -0.254 9 -4.486 5 0.47 1 -0.785 3 0.938 1
565 P203 max T 4.316 5 0.166 1 4.056 5 1.812 1 7.031 5
566 min -0.079 9 -3.797 5 0.55 9 -0.76 2 1.141 9
567 max B 3.765 5 0.061 9 4.096 5 2.262 9 7.102 5
568 min -0.198 1 -4.427 5 0.533 9 -0.374 10 1.098 9
569 P189 max T 4.252 5 -0.095 2 3.911 5 2.146 2 6.783 5
570 min 0.521 9 -3.57 5 0.358 2 -0.676 3 0.674 2
571 max B 4.11 5 -0.536 9 4.226 5 1.053 9 7.32 5
572 min 0.076 2 -4.341 5 0.314 2 -0.644 10 0.593 2
573 P192 max T 4.321 5 -0.152 8 3.873 5 1.255 8 6.723 5
574 min 0.379 1 -3.424 5 0.397 1 -0.721 9 0.687 1
575 max B 4.121 5 -0.355 1 4.149 5 0.957 12 7.186 5
576 min 0.155 8 -4.177 5 0.372 8 -0.755 1 0.68 8
577 P141 max T 4.186 9 0.08 6 2.299 9 2.024 12 4.406 9
578 min -0.05 1 -2.028 3 0.226 1 0.176 1 0.479 1
579 max B 2.044 3 -0.015 1 2.311 9 1.981 5 4.398 9
580 min 0.009 6 -4.134 9 0.056 1 0.257 6 0.106 1
581 P117 max T 4.159 9 0.089 12 2.277 9 1.816 12 4.37 9
582 min -0.051 5 -2.016 3 0.129 5 -0.185 1 0.288 5
583 max B 1.973 3 -0.135 5 2.279 9 1.505 2 4.34 9
584 min -0.009 12 -4.083 9 0.07 5 -0.172 5 0.138 5
585 P83 max T 4.131 1 0.089 10 2.263 1 2.01 4 4.342 1
586 min -0.054 5 -2.019 7 0.125 5 -0.019 5 0.281 5
587 max B 1.984 7 -0.139 9 2.256 1 1.986 9 4.291 1
588 min -0.011 10 -4.029 1 0.087 5 0.05 10 0.161 5
589 P42 max T 4.078 1 0.081 4 2.238 1 1.743 4 4.291 1
590 min -0.041 9 -1.948 7 0.219 9 -0.229 5 0.46 9
591 max B 1.956 7 -0.017 9 2.259 1 1.729 9 4.304 1
592 min -0.004 4 -4.052 1 0.059 9 -0.113 10 0.11 9
593 P115 max T 1.742 3 0.004 1 2.13 9 1.931 2 4.109 9
594 min -0.014 6 -3.94 9 0.034 1 0.275 6 0.07 1
595 max B 3.868 9 0.046 6 2.132 9 2.081 12 4.08 9
596 min 0.017 1 -1.695 3 0.175 1 -0.359 1 0.342 1
597 P144 max T 1.67 3 -0.087 2 2.102 9 1.564 2 4.058 9
598 min -0.032 12 -3.896 9 0.126 5 -0.056 5 0.231 5
599 max B 3.833 9 0.047 12 2.106 9 1.849 12 4.036 9
600 min 0.062 4 -1.684 3 0.176 5 -0.198 1 0.316 5
601 P205 max T 3.841 5 0.069 2 2.105 5 1.986 8 4.038 5
602 min -0.023 9 -1.682 11 0.052 9 -0.399 9 0.117 9
603 max B 1.649 11 -0.137 1 2.094 5 2.034 1 3.98 5
604 min -0.02 2 -3.731 5 0.12 9 0.128 2 0.213 9
605 P86 max T 1.658 7 0.016 9 2.08 1 1.573 6 4.019 1
606 min -0.021 4 -3.861 1 0.018 9 -0.535 9 0.046 9
607 max B 3.752 1 0.044 4 2.067 1 1.759 4 3.958 1
608 min 0.003 9 -1.613 7 0.16 9 -0.248 5 0.319 9
609 P39 max T 1.678 7 -0.078 9 2.074 1 1.936 6 4.001 1
610 min -0.038 10 -3.835 1 0.14 5 0.199 10 0.251 5


611 max B 3.808 1 0.049 10 2.092 1 2.065 4 4.009 1
612 min 0.061 6 -1.69 7 0.201 5 -0.66 5 0.355 5
613 P181 max T 3.764 5 0.065 8 2.067 5 1.724 8 3.962 5
614 min -0.036 1 -1.629 11 0.065 1 -0.197 9 0.151 1
615 max B 1.638 11 -0.073 1 2.091 5 1.496 11 3.984 5
616 min -0.021 8 -3.75 5 0.065 1 -0.52 1 0.112 1
617 P208 max T 1.328 11 -0.058 10 1.905 5 1.57 10 3.686 5
618 min -0.042 8 -3.546 5 0.11 1 -0.235 1 0.192 1
619 max B 3.43 5 0.028 8 1.889 5 1.745 8 3.616 5
620 min 0.057 12 -1.294 11 0.171 1 -0.214 9 0.297 1
621 P179 max T 1.34 11 -0.055 12 1.905 5 1.982 1 3.675 5
622 min -0.046 2 -3.523 5 0.17 9 0.196 2 0.298 9
623 max B 3.508 5 0.034 2 1.926 5 2.27 9 3.692 5
624 min 0.048 10 -1.344 11 0.235 9 0.328 10 0.409 9
625 P145 max T 3.244 9 -0.058 6 1.915 9 1.87 12 3.574 9
626 min 0.014 1 -1.623 3 0.113 1 -0.015 1 0.22 1
627 max B 1.616 3 -0.025 1 1.908 9 1.854 5 3.537 9
628 min 0.082 6 -3.17 9 0.054 1 0.114 6 0.098 1
629 P112 max T 3.204 9 -0.047 12 1.889 9 2.098 12 3.527 9
630 min 0.011 5 -1.587 3 0.054 5 -0.015 1 0.102 5
631 max B 1.557 3 -0.073 5 1.879 9 1.634 2 3.483 9
632 min 0.005 5 -3.121 9 0.039 5 -0.071 5 0.075 5
633 P87 max T 3.19 1 -0.046 10 1.88 1 1.861 4 3.51 1
634 min 0.027 5 -1.608 7 0.057 5 -0.561 5 0.104 5
635 max B 1.581 7 -0.091 10 1.866 1 1.855 9 3.458 1
636 min 0.018 5 -3.096 1 0.058 5 -0.154 10 0.108 5
637 P40 max T 3.157 1 -0.053 4 1.864 1 1.943 4 3.478 1
638 min 0.015 9 -1.543 7 0.116 9 -0.039 5 0.224 9
639 max B 1.534 7 -0.027 9 1.86 1 1.781 9 3.45 1
640 min 0.071 4 -3.094 1 0.061 9 0.028 10 0.111 9
641 P73 max T 2.878 9 -0.089 1 1.778 9 1.64 12 3.271 9
642 min 0.093 5 -1.479 3 0.128 1 -0.679 1 0.225 1
643 max B 1.48 3 0.011 1 1.812 9 1.537 2 3.328 9
644 min 0.041 6 -2.918 9 0.052 1 -0.127 6 0.11 1
645 P209 max T 2.973 5 -0.047 9 1.751 5 2.087 9 3.27 5
646 min 0.088 9 -1.351 11 0.067 9 0.248 10 0.119 9
647 max B 1.327 11 -0.116 1 1.736 5 1.89 1 3.216 5
648 min 0.047 9 -2.879 5 0.092 9 -0.031 2 0.167 9
649 P98 max T 1.246 3 -0.073 5 1.736 9 1.799 5 3.237 9
650 min 0.014 1 -2.936 9 0.082 1 0.103 6 0.157 1
651 max B 2.852 9 -0.068 6 1.723 9 1.914 12 3.191 9
652 min 0.118 5 -1.214 3 0.127 1 -0.73 1 0.221 1
653 P176 max T 2.922 5 -0.039 1 1.724 5 1.929 8 3.218 5
654 min 0.016 1 -1.307 11 0.027 1 -0.025 9 0.048 1
655 max B 1.299 11 -0.054 1 1.722 5 1.627 11 3.195 5
656 min 0.031 1 -2.865 5 0.043 1 -0.342 1 0.075 1
657 P67 max T 2.824 9 -0.036 5 1.748 9 1.993 11 3.214 9
658 min 0.072 12 -1.417 3 0.119 5 -0.436 12 0.222 5
659 max B 1.437 3 0 5 1.784 9 1.953 2 3.275 9
660 min 0.001 12 -2.871 9 0.023 5 0.36 6 0.045 5
661 P22 max T 2.809 1 -0.039 5 1.739 1 2.096 5 3.196 1
662 min 0.081 10 -1.449 7 0.137 5 -0.069 6 0.256 5
663 max B 1.468 7 -0.039 5 1.777 1 1.541 6 3.265 1
664 min 0.007 10 -2.865 1 0.044 5 -0.354 10 0.076 5
665 P142 max T 1.188 3 -0.123 1 1.708 9 1.693 2 3.185 9


666 min 0.025 5 -2.888 9 0.105 12 0.027 5 0.192 12
667 max B 2.81 9 -0.05 12 1.697 9 2.032 12 3.142 9
668 min 0.164 4 -1.179 3 0.155 5 -0.02 1 0.271 5
669 P19 max T 2.803 1 -0.094 9 1.731 1 1.984 3 3.184 1
670 min 0.117 5 -1.395 7 0.119 9 -0.688 4 0.207 9
671 max B 1.398 7 0.005 9 1.763 1 1.957 6 3.235 1
672 min 0.032 4 -2.834 1 0.064 9 0.355 10 0.131 9
673 P43 max T 1.211 7 -0.106 9 1.692 1 1.807 9 3.155 1
674 min 0.04 5 -2.859 1 0.106 10 -0.056 10 0.193 10
675 max B 2.793 1 -0.053 10 1.686 1 2.167 5 3.123 1
676 min 0.144 9 -1.201 7 0.163 10 0.196 6 0.302 10
677 P84 max T 1.167 7 -0.095 5 1.688 1 1.701 6 3.149 1
678 min 0.005 9 -2.858 1 0.06 9 -0.128 9 0.117 9
679 max B 2.761 1 -0.063 4 1.67 1 1.903 4 3.091 1
680 min 0.096 9 -1.136 7 0.109 9 -0.051 5 0.19 9
681 P96 max T 2.479 9 0.022 1 1.732 9 2.098 1 3.091 9
682 min -0.032 6 -1.312 3 0.201 1 -0.257 2 0.414 1
683 max B 1.355 3 -0.034 1 1.887 9 1.37 2 3.383 9
684 min -0.007 1 -2.759 9 0.014 1 -0.363 6 0.031 1
685 P102 max T 2.406 9 0.033 5 1.696 9 2.227 11 3.022 9
686 min -0.067 12 -1.218 3 0.205 5 -0.083 12 0.427 5
687 max B 1.312 3 0.012 12 1.853 9 2.139 2 3.32 9
688 min 0.033 5 -2.701 9 0.04 12 0.534 111 0.087 12
689 P18 max T 2.397 1 0.037 5 1.687 1 1.886 5 3.007 1
690 min -0.068 10 -1.271 7 0.232 5 -0.267 6 0.433 32
691 max B 1.361 7 0.008 10 1.853 1 2.247 10 3.324 1
692 min 0.019 5 -2.719 1 0.049 10 -0.259 79 0.103 10
693 P15 max T 2.406 1 0.011 9 1.683 1 2.209 3 3.004 1
694 min -0.042 4 -1.211 7 0.178 9 -0.237 4 0.361 9
695 max B 1.259 7 -0.033 9 1.831 1 2.148 6 3.278 1
696 min 0.035 9 -2.66 1 0.034 9 0.528 10 0.058 9
697 P151 max T 2.616 5 -0.036 9 1.619 5 1.953 9 2.976 5
698 min 0.099 1 -1.219 11 0.134 9 -0.064 10 0.251 9
699 max B 1.236 11 -0.133 9 1.657 5 1.552 1 3.045 5
700 min 0.046 2 -2.674 5 0.093 9 -0.327 2 0.166 9
701 P147 max T 2.596 5 -0.033 1 1.602 5 1.976 7 2.948 5
702 min 0.108 9 -1.187 11 0.092 1 -0.725 8 0.169 1
703 max B 1.189 11 -0.045 1 1.632 5 1.95 10 2.995 5
704 min 0.032 1 -2.623 5 0.038 1 0.151 1 0.067 1
705 P131 max T 1.072 3 -0.098 5 1.589 9 1.595 5 2.917 9
706 min 0.028 1 -2.554 9 0.094 1 -0.256 6 0.176 1
707 max B 2.6 9 -0.026 1 1.624 9 1.806 1 2.978 9
708 min 0.083 5 -1.093 3 0.13 1 -0.06 2 0.248 1
709 P162 max T 0.948 11 -0.078 1 1.554 5 1.843 1 2.897 5
710 min 0.05 2 -2.625 5 0.163 2 -0.008 2 0.305 2
711 max B 2.565 5 -0.057 2 1.549 5 2.044 9 2.869 5
712 min 0.093 1 -0.938 11 0.168 2 0.193 10 0.312 2
713 P206 max T 0.922 11 -0.087 9 1.542 5 1.701 10 2.877 5
714 min 0.045 1 -2.613 5 0.147 1 -0.051 1 0.275 1
715 max B 2.514 5 -0.062 8 1.523 5 1.884 8 2.818 5
716 min 0.107 9 -0.895 11 0.162 1 -0.036 9 0.29 1
717 P104 max T 1.03 3 -0.124 12 1.561 9 1.936 2 2.864 9
718 min 0.048 5 -2.507 9 0.104 12 0.239 5 0.18 12
719 max B 2.548 9 -0.039 5 1.594 9 1.986 11 2.921 9
720 min 0.098 12 -1.03 3 0.115 12 -0.601 12 0.2 12


721 P62 max T 1.061 7 -0.114 10 1.552 1 1.589 9 2.85 1
722 min 0.055 5 -2.498 1 0.102 10 -0.522 10 0.177 10
723 max B 2.529 1 -0.052 5 1.583 1 1.696 5 2.901 1
724 min 0.094 10 -1.063 7 0.115 10 -0.068 6 0.2 10
725 P65 max T 0.99 7 -0.114 5 1.538 1 1.942 6 2.82 1
726 min 0.022 9 -2.466 1 0.068 9 0.043 9 0.126 9
727 max B 2.523 1 -0.018 9 1.575 1 2.296 4 2.888 1
728 min 0.108 5 -1.01 7 0.105 9 0.251 5 0.201 9
729 P160 max T 2.226 5 0.021 9 1.568 5 1.797 9 2.795 5
730 min -0.04 2 -1.063 11 0.203 9 -0.255 10 0.417 9
731 max B 1.142 11 -0.006 2 1.731 5 2.34 2 3.107 5
732 min 0.011 9 -2.547 5 0.097 2 -0.257 39 0.191 2
733 P166 max T 2.222 5 0.02 1 1.555 5 2.191 7 2.774 5
734 min -0.026 8 -1.028 11 0.149 1 -0.271 8 0.308 1
735 max B 1.073 11 -0.016 8 1.695 5 2.133 10 3.034 5
736 min -0.007 1 -2.459 5 0.082 1 0.391 1 0.168 1
737 P100 max T 0.959 3 -0.081 6 1.548 9 1.418 5 2.761 9
738 min 0.009 1 -2.208 9 0.116 1 -0.61 6 0.228 1
739 max B 2.502 9 0.031 1 1.707 9 1.666 1 3.062 9
740 min 0.002 6 -1.053 3 0.211 6 -0.263 2 0.422 6
741 P69 max T 0.916 3 0.008 12 1.516 9 2.133 2 2.701 9
742 min 0.047 5 -2.15 9 0.12 12 0.374 5 0.244 12
743 max B 2.43 9 0.005 5 1.67 9 2.207 11 2.991 9
744 min -0.053 12 -0.959 3 0.197 12 -0.14 12 0.423 12
745 P64 max T 0.966 7 0.017 10 1.512 1 2.158 10 2.699 1
746 min 0.044 5 -2.164 1 0.127 10 -0.273 11 0.263 10
747 max B 2.418 1 -0.004 5 1.661 1 1.578 5 2.975 1
748 min -0.054 10 -1.013 7 0.201 10 -0.279 6 0.432 10
749 P61 max T 0.876 1 -0.051 4 1.49 1 2.147 6 2.654 1
750 min 0.008 9 -2.105 1 0.081 9 0.138 9 0.159 9
751 max B 2.427 1 0.032 9 1.656 1 2.192 3 2.97 1
752 min -0.012 4 -0.954 7 0.193 9 -0.357 4 0.394 4
753 P195 max T 0.822 11 -0.076 1 1.425 5 1.655 1 2.617 5
754 min 0.06 9 -2.294 5 0.137 2 -0.466 2 0.238 2
755 max B 2.32 5 -0.077 9 1.454 5 1.623 9 2.664 5
756 min 0.088 1 -0.825 11 0.117 2 -0.056 10 0.206 2
757 P168 max T 0.776 11 -0.083 9 1.4 5 1.936 11 2.566 5
758 min 0.042 1 -2.242 5 0.163 1 0.182 1 0.284 8
759 max B 2.301 5 -0.054 1 1.437 5 2.225 8 2.635 5
760 min 0.099 9 -0.792 11 0.141 8 0.268 9 0.25 8
761 P164 max T 0.785 5 0.012 2 1.388 5 2.214 2 2.478 5
762 min 0.044 9 -1.99 5 0.168 2 -0.301 3 0.342 2
763 max B 2.227 5 -0.05 9 1.529 5 1.497 9 2.739 5
764 min -0.017 2 -0.831 5 0.145 2 -0.26 10 0.3 2
765 P148 max T 0.803 5 -0.009 8 1.352 5 2.13 11 2.405 5
766 min 0.028 1 -1.901 5 0.182 8 0.286 1 0.36 8
767 max B 2.222 5 -0.028 1 1.515 5 2.172 7 2.717 5
768 min 0.008 8 -0.807 5 0.147 8 -0.443 8 0.289 8
Envelope AISC 15TH (360-16): LRFD Member Steel Code Checks

Member Shape Code Check Loc[in] LC Shear Check Loc[in]Dir LC phi*Pnc [lb] phi*Pnt [lb] phi*Mn y-y [lb-ft] phi*Mn z-z [lb-ft] Cb Eqn
1 SPL10 0.375"X6"WIDEPLATE 0.197 1.877 12 1.026 0 y 1 69210.805 72900 569.533 9112.5 1.33 H1-1b
2 SPL9 0.375"X6"WIDEPLATE 0.232 1.877 10 0.99 0 y 9 69210.805 72900 569.533 9112.5 1.335H1-1b

Envelope AISC 15TH (360-16): LRFD Member Steel Code Checks (Continued)
7 CPL6 0.375"X7"WIDEPLATE 0.19 7.391 6 0.695 7.391 y 5 62644.96 85050 664.454 12403.125 1.33 H1-1b
8 CPL10 0.375"X7"WIDEPLATE 0.147 6.116 7 0.658 0 y 7 65500.326 85050 664.454 11880.679 1.033H1-1b
12 SPL5 0.375"X6"WIDEPLATE 0.22 2.7 8 0.51 2.7 y 7 63949.359 72900 569.533 9112.5 1.352H1-1b
14 CPL11 0.375"X7"WIDEPLATE 0.138 8.25 12 0.491 7.391 y 12 62644.96 85050 664.454 12403.125 1.577H1-1b
15 SR3 PIPE_2.0 0.761 11.25 10 0.487 96.75 6 12143.947 32130 1871.625 1871.625 1 H3-6
16 SR2 PIPE_2.0 0.856 54 8 0.485 6.75 6 12143.947 32130 1871.625 1871.625 1 H3-6
18 SR1 PIPE_2.0 0.71 96.75 10 0.458 96.75 10 12143.947 32130 1871.625 1871.625 1 H3-6
28 3c PIPE_2.5 0.329 36.25 1 0.194 36.25 7 22373.407 50715 3596.25 3596.25 1 H1-1b
29 2c PIPE_2.5 0.311 36.25 5 0.178 36.25 10 22373.407 50715 3596.25 3596.25 1 H1-1b
30 1a PIPE_2.5 0.347 36.25 5 0.169 61.25 12 22373.407 50715 3596.25 3596.25 1 H1-1b
31 3a PIPE_2.5 0.333 36.25 9 0.166 61.25 4 22373.407 50715 3596.25 3596.25 1 H1-1b
32 2a PIPE_2.5 0.304 36.25 1 0.163 61.25 2 22373.407 50715 3596.25 3596.25 1 H1-1b
33 ICA5 HSS3X3X3 0.189 0 7 0.161 25.612 z 1 75009.437 78246 6796.5 6796.5 1.426H1-1b
34 1b PIPE_2.5 0.591 60 1 0.157 25 4 22373.407 50715 3596.25 3596.25 1 H1-1b
35 ICA6 HSS3X3X3 0.202 0 2 0.157 28.59 z 10 75009.437 78246 6796.5 6796.5 1.506H1-1b
36 ICA4 HSS3X3X3 0.223 0 10 0.156 28.59 z 6 75009.437 78246 6796.5 6796.5 1.535H1-1b
37 2b PIPE_2.5 0.579 60 9 0.147 25 1 22373.407 50715 3596.25 3596.25 1 H1-1b
38 ICA3 HSS3X3X3 0.218 0 12 0.144 25.612 z 5 75009.437 78246 6796.5 6796.5 1.528H1-1b
39 ICA2 HSS3X3X3 0.217 0 4 0.14 25.612 z 9 75009.437 78246 6796.5 6796.5 1.496H1-1b
40 3b PIPE_2.5 0.578 60 5 0.138 25 8 22373.407 50715 3596.25 3596.25 1 H1-1b
41 SRCPL3 L7.19X4.73X5 0.254 0 2 0.131 34.79 y 8 82765.464 117525.946 4341.905 13008.77 1.5 H2-1
42 SO2 HSS4X4X6 0.352 0 9 0.127 0 z 6 188726.792 197892 22045.5 22045.5 1.951H1-1b
43 ICA1 HSS3X3X3 0.249 0 6 0.126 25.612 z 1 75009.437 78246 6796.5 6796.5 1.47 H1-1b
44 SO3 HSS4X4X6 0.345 0 1 0.12 0 z 10 188726.792 197892 22045.5 22045.5 1.972H1-1b
45 SO1 HSS4X4X6 0.319 0 5 0.082 0 y 4 188726.792 197892 22045.5 22045.5 2.047H1-1b
46 FH1 HSS3.5X3.5X4 0.128 26.25 6 0.075 72.5 y 2 68865.1 120474 12075 12075 1.719H1-1b
47 FH3 HSS3.5X3.5X4 0.155 26.25 9 0.072 47.5 y 8 68865.1 120474 12075 12075 1.512H1-1b
48 FH2 HSS3.5X3.5X4 0.128 26.25 1 0.064 60 y 6 68865.1 120474 12075 12075 1.656H1-1b
49 OCA5 HSS4X4X4 0.156 0 5 0.062 6.708 y 5 138725.511 139518 16180.5 16180.5 1.727H1-1b
50 OCA3 HSS4X4X4 0.172 0 8 0.057 0 z 1 138725.511 139518 16180.5 16180.5 1.951H1-1b
51 SRCPL1 L7.19X4.73X5 0.282 0 6 0.056 0 y 6 82765.464 117525.946 4341.905 13008.77 1.5 H2-1
52 OCA2 HSS4X4X4 0.166 0 2 0.055 0 z 9 138725.511 139518 16180.5 16180.5 1.897H1-1b
53 OCA4 HSS4X4X4 0.167 0 9 0.054 6.708 y 8 138725.511 139518 16180.5 16180.5 1.854H1-1b
54 SRCPL2 L7.19X4.73X5 0.282 0 10 0.052 0 y 10 82765.464 117525.946 4341.905 13008.77 1.5 H2-1
55 OCA1 HSS4X4X4 0.168 0 12 0.052 0 z 5 138725.511 139518 16180.5 16180.5 1.921H1-1b
56 OCA6 HSS4X4X4 0.173 0 5 0.047 0 z 11 138725.511 139518 16180.5 16180.5 1.956H1-1b
57 GA6 L2X2X3 0.34 28.29 6 0.039 28.29 y 6 20796.598 23392.8 557.717 1239.29 1.5 H2-1
58 GA3 L2X2X3 0.234 0 3 0.028 0 y 3 20796.598 23392.8 557.717 1239.29 1.5 H2-1
59 GA4 L2X2X3 0.252 28.29 8 0.022 28.29 y 10 20796.598 23392.8 557.717 1239.29 1.5 H2-1

Envelope AISC 15TH (360-16): LRFD Member Steel Code Checks (Continued)
60 GA2 L2X2X3 0.23 28.29 12 0.021 28.29 y 2 20796.598 23392.8 557.717 1239.29 1.5 H2-1
61 GA5 L2X2X3 0.201 0 2 0.019 0 y 12 20796.598 23392.8 557.717 1239.29 1.5 H2-1
62 GA1 L2X2X3 0.185 0 131 0.018 0 y 7 20796.598 23392.8 557.717 1239.29 1.5 H2-1
63 1c PIPE_2.5 0.111 36.25 7 0.007 36.25 7 22373.407 50715 3596.25 3596.25 1 H1-1b

November 29, 2024
APPENDIX D
ADDITIONAL CALCUATIONS
Site Name: NORTH BEAUFORT
Site Number: 812676
Analysis Date: PP 11/29/2024
Mount Connection Check
Connecting Bolt Information Support Arm Information Connecting Plate Information

Bolt Configuration = Standard Shape = Rectangular Thickness = 0.625 in
Number of Bolts = 4 Height = 4 in Material = A36
Bolt Diameter = 5/8 in Width = 4 in Weld Information
Bolt Grade = A325 Thickness = 0.375 in Weld Size = 0.25 in
Threads in Shear = Yes Material = Other FEXX = 70 ksi
Horizontal Bolt Spacing = 6 in Weld Information Assumed?
Vertical Bolt Spacing = 6 in
Design Code: TIA

Factored Reactions (RISA-3D)
Axial Vx = -1805 lb
Vy = 3035 lb
Vz = 36 lb
Torque Mx = 42 lb-ft
My = -63 lb-ft
Mz = 7605 lb-ft
Bolt Forces Weld Forces

Max Tensile Force = 8.12 kip Z-axis weld shear stress = 0.004 kip/in
Max Shear Force = 0.78 kip Y-axis weld shear stress = 0.379 kip/in
Bolt Capacities Z-axis weld torsional stress = 0.012 kip/in
Design Tensile Strength = 20.34 kip Y-axis weld torsional stress = 0.012 kip/in
Design Shear Strength = 13.81 kip Weld axial stress = 0.113 kip/in
Bolt Tensile Capacity = 39.9% Pass Z-axis weld bending stress = 4.278 kip/in
Bolt Shear Capacity = 5.7% Pass Y-axis weld bending stress = 0.036 kip/in
Combined Shear and Tension = 16.3% Pass Z-direction total force = 0.016 kip/in
Y-direction total force = 0.391 kip/in
X-direction total force = 4.426 kip/in
Weld Resultant force = 2.986 kip/in
Weld Capacities
ϕRn = 5.568 kip/in
Capacity = 53.6% Pass

SGS_ 2411133 _812676_683683_Rev.0_MountAnalysis_Pass_T-Mobile_133ft_11.29.2024

Uploaded by

Copyright:

Available Formats

SGS_ 2411133 _812676_683683_Rev.0_MountAnalysis_Pass_T-Mobile_133ft_11.29.2024

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SGS_ 2411133 _812676_683683_Rev.0_MountAnalysis_Pass_T-Mobile_133ft_11.29.2024

Uploaded by

Copyright:

Available Formats

Date: November 29, 2024

Sinnott Gering and Schmitt Towers, Inc.

Subject: Mount Analysis Report

Carrier Designation: T-Mobile Equipment Change-Out

Crown Castle Designation: Crown Castle BU Number: 812676

Engineering Firm Designation: SGS Towers Report Designation: 2411133

Structure Information: Structure Height & Type: 150 ft Monopole Tower

Platform Mount Sufficient

Mount analysis prepared by: Pavitra Prabhu DRS

Table 1 - Proposed Equipment Configuration

Table 2 - Documents Provided

3.1) Analysis Method

Table 3 - Mount Component Stresses vs. Capacity (Platform, All Sectors)

Structure Rating (max from all components) = 102.6%

WIRE FRAME AND RENDERED MODELS

SGS Towers, Inc. 812676 (NORTH BEAUFORT) SK-1

SOFTWARE INPUT CALCULATIONS

Design Ice Thickness ti 0.5 in

Risk Category II TIA-222-H - Table 2-1

Design Parameters Summary

Seismic Parameters Summary

Vertical seismic load effects Ev 294 lb TIA-222-H - 2.7.6

Maintenance Parameters Summary

Appurtenance Loading Summary

https://ascehazardtool.org/ Page 1 of 3 Mon Nov 25 2024

Site Soil Class: D - Stiff Soil

Seismic Design MCE R Response Spectrum

Sa (g) vs T(s) Sa (g) vs T(s)

MCER Vertical Response Spectrum Design Vertical Response Spectrum

Sa (g) vs T(s) Sa (g) vs T(s)

Data Accessed: Mon Nov 25 2024

https://ascehazardtool.org/ Page 2 of 3 Mon Nov 25 2024

https://ascehazardtool.org/ Page 3 of 3 Mon Nov 25 2024

SOFTWARE ANALYSIS OUTPUT

Basic Load Cases

RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 1

Basic Load Cases (Continued)

RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 2

Load Combinations (Continued)

RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 3

Load Combinations (Continued)

Node Boundary Conditions

RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 4

Node Boundary Conditions (Continued)

Member Primary Data

RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 5

Member Primary Data (Continued)

RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 6

Member Primary Data (Continued)

RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 7

Member Primary Data (Continued)

Member Advanced Data

RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 8

Member Advanced Data (Continued)

RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 9

Member Advanced Data (Continued)

RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 10

Member Advanced Data (Continued)

Hot Rolled Steel Properties

RISA-3D Version 22 [ Mount Rushmore 2024-10-14.r3d ] Page 11