to 240°C taking the specific heat of the iron as 0.

46
kJ/kg-K.
Name: ___________________________________
a. 1 BTU c. 246. 36 kJ
Score: __________ b. 338.75 kJ d. 215.83 BTU
10. Determine the average Cp value in kJ/kg-K of a gas
1. The temperature of a solution is 31°C. What is this if 494.7867299 BTU of heat is necessary to raise
temperature in Rankine? the temperature from 300 K to 800 K making the
a. 560.8 c. 520.8 pressure constant.
b. 575.5 d. 547.8 a. 1.44 c. 1.45
2. Two thermometers, one Celsius and the other b. 1.044 d. 1.038
Fahrenheit, are both at the same temperature, but 11. What mass of nitrogen is contained in a 57 m³ tank
the reading on the Fahrenheit thermometer is if the pressure and temperature are 1 atm and
exactly twice that on the Celcius thermometer, 21°C respectively?
what is the temperature? a. 66.1 kg c. 70.4 kg
a. 160°C c. 40°C b. 56.3 kg d. 41.69 kg
b. 80°C d. 320°C 12. A 0.71 m³ tank contains 4.5 kg of an ideal gas. The
3. Supposing two liquid of different densities gas ha a molecular weight of 44 and is at 21°C.
ρ=1500 kg /m ³ and ρ=500 kg /m ³ were What is the pressure of the gas?
poured together inside a 100L tank, filling it. If the a. 352.2 kPa c. 532.2 kPa
resulting density of the mixture is 800 kg /m³ , b. 325.2 kPa d. 523.2 kPa
find the respective quantities of liquids used. 13. A volume of 450 cm³ of air is measured at a
a. 35 kg and 45 kg c. 25 kg and 55 kg pressure of 740 mm Hg absolute and a
b. 30 kg and 50 kg d. 20 kg and 60 kg temperature of 20°C. What is the volume in cm³ at
4. A fluid moves in a steady flow manner between 760 mm Hg absolute and 0°C?
two sections in the same flowline. At section 1: a. 516.12 c. 620.76
A1 = 0.10 m², V1 = 6 m/s, ν1 = 0.33 m³/kg. At section b. 408.25 d. 375.85
2: A2 = 0.2 m², ρ 2=0.27 kg / m ³ . Calculate for 14. A closed vessel contains air at a pressure of 160 kPa
the velocity of flow of section 2. gauge and temperature of 30°C. The air is heated
a. 37.63 m/s c. 40.62 m/s at constant volume to 60°C with the atmospheric
b. 33.67 m/s d. 46.02 m/s pressure of 759 mm Hg. What is the final gauge
5. A tank contains water. What is the intensity pressure?
absolute of pressure at a depth of 6m? a. 287.05 kPa c. 167 kPa
a. 58.86 kPa c.158.86 kPa b. 186 kPa d. 272 kPa
b. 68.5 kPa d. 160.185 kPa 15. An air bubble rises from the bottom of a well
6. Convert a vacuum pressure of 110 mm of mercury where the temperature is 25°C , to the surface
into absolute pressure. Atmospheric pressure is where the temperature is 27°C. Find the percent
10.5 m of H2O. increase in the volume of the bubble. If the depth
a. 3.7 m of H2O c. 9.1 m of H2O of the well is 6 m. Atmospheric pressure is 101,528
b. 45.6 m of H2O d. 99.5 m of H2O Pa.
7. Which of the following is equivalent to 1 chu? a. 49.3% c. 41.3%
a. 1400.4 ft-lb c. 9/5 Btu b. 59.3% d. 65.4%
b. 1.899 kJ d. all of these 16. Ammonia weighing 22 kg is confined inside a
8. How much power is there in the kinetic energy of cylinder equipped with a piston has an initial
the atmosphere density = 1.217 kg /m³ at 56 pressure of 413 kPa at 38°C. If 2900 kJ of heat is
kph wind velocity? Consider the section that passes added to the ammonia until its pressure and
through a 3 m. diameter circular area normal to the temperature are 413 kPa and 100°C respectively.
velocity. What is the amount of work done by the fluid in
a. 10.21 kW c. 16.21 kW BTU?
b. 15.21 kW d. 17.21 kW a. 667 c. 420
9. Calculate the quantity of heat to be transferred to b. 304 d. 632
2.25 kg of iron to raise its temperature from 20°C
This study source was downloaded by 100000889195261 from CourseHero.com on 08-11-2024 00:55:19 GMT -05:00

https://www.coursehero.com/file/106114580/PIPE-1-QUESTIONNAIREdocx/
17. How much work is necessary to compress air in an 27. What is the amount of heat added to 15 kg of air to
insulated cylinder from 0.20 m³ to 0.01 m³. Use t1= increase its temperature from 30 oC to 250 oC
20°C and P1= 100 kPa. without changing the pressure?
a. 115.7 kJ c. 113.4 kJ a. 3230.46 kJ c. 3420.26 kJ
b. 46.3 kJ d. 19 kJ b. 3320.46 kJ d. 3640.36 kJ
18. Carnot cycle operates between 30°C and 350°C. 28. Determine the compressor work of a Brayton cycle
if its pressure ratio is 8 and the initial temperature
Find the cycle efficiency.
is 32 oC.
a. 76.45% c. 45.37%
a. 248.67 kJ/kg c. 278.47 kJ/kg
b. 63.45% d. 51.36% b. 284.67 kJ/kg d. 267.84 kJ/kg
19. Oil flows full bore at a velocity of 2 m/s through a 29. If the specific humidity of moist air is 0.027 at 1
nest of 16 tubes in a single pass cooler. The internal atmosphere pressure. What is the partial pressure
diameter of the tubes is 30 mm and the density of of the water vapor in the mixture?
the oil is 0.85 g/li. Find the volume flow in liters per a. 4.215 Kpaa c. 3.516 Kpaa
second. b. 3.617 Kpaa d. 2.584 kPaa
a. 20 c. 22 30. If the enthalpy of a certain gas is 2400 kJ/kg and its
b. 21 d. 23 internal energy is 2200 kJ/kg, find the specific
20. Calculate the quantity of heat to be transferred to volume at a pressure of 950 kPaa.
2.25 kg of brass to raise its temperature from 20°C a. 0.2105 m3/kg c. 0.2501 m3/kg
3
to 240°C taking the specific heat of the brass as b. 0.2015 m /kg d. 0.1025 m3/kg
31. Determine the maximum temperature of a Carnot
0.394 kJ/kg-K.
cycle if it operates at a minimum temperature of 20
a. 519.03 Kj c. 195.03 kJ o
C with an efficiency of 60 %.
b. 159.03 kJ d. 591.03 kJ a. 459.5 oC c. 455.9 oC
o
21. An air-vapor mixture has a DB temperature of 30 oC b. 495.5 C d. 559.4 oC
o
and a humidity ratio of 0.015 kg/kg d.a. Calculate 32. Air at 1 MPaa and 310 C is expanded to 250 kPaa
the enthalpy. in accordance with the relation pV1.25 = C.
a. 68.527 kJ/kg d.a. c. 58.527 kJ/kg d.a. Determine the work done.
b. 78.527 kJ/kg d.a. d. 88.527 kJ/kg d.a. a. + 162.11 kJ/kg c. – 162.11 kJ/kg
22. What is the specific gravity of a fuel at 28 o Baume? b. + 126.11 kJ/kg d. – 126.11 kJ/kg
a. 0.868 c. 0.68 33. A Rankine cycle operates with a thermal efficiency
b. 0.886 d. 986 of 40 % and the factor of evaporation of the boiler
23. Calculate the moisture content of moist air at 20 oC is 1.15. Determine the mass flow rate of steam if
DB, 15 oC WB, and 95 kPa barometric pressure. Let the cycle power output is 5.5 MW.
the saturation pressure of water at 15 oC equals to a. 5.3 kg/s c. 4.3 kg/s
1.7057 kPaa and at 20 oC is 2.339 kPaa. b. 3.5 kg/s d. 6.3 kg/s
a. 0.00923 kg/kg d.a. c. 0.00293 kg/kg d.a. 34. The mixing ratio of humid air is 0.034 at a dry-bulb
b. 0.00392 kg/kg d.a. d. 0.00239 kg/kg d.a. temperature of 27°C. Determine the enthalpy of
24. Determine the mass of a nitrogen gas confined in a
the given air. hg @27 °C = 2550.8 KJ/kg.
6 m3 tank at a pressure of 198.675 kPag and
a. 67.25 kJ/kg c. 80.62 KJ/kg
temperature of 40 oC.
a. 18.4 kg c. 19.4 kg b. 113.69 KJ/kg d. 55.68 KJ/kg
b. 20.4 kg d. 17.4kg 35. The dry bulb temperature of humid air is 35°C.
25. The heat rejected from condenser is 300 kW. The What is the wet-bulb depression in °F if the wet-
water required to cool the refrigerant is 5 lps. bulb temperature is 18°C?
Determine the temperature of water leaving the a. 17.6 c. 30.6
condenser if water enters at 25 C. b. 18.0 d. 25.8
a. 39.33 oC c. 33.39 oC 36. The enthalpies at the entrance and exit of a steam
b. 33.93 oC d.43.93 oC engine are 2700 kJ/kg and 2000 kJ/kg, respectively.
26. Determine the resulting pressure when one The steam consumption of the engine is 1000
kilogram of air at 103 kPaa and 95 oC is heated at kg/hr. If the indicated efficiency is 66 % and the
constant volume to 425 oC. mechanical efficiency is 92 %, determine the
a. 205.36 kPaa c. 195.35 kPaa engine brake power output.
b. 196.35 kPaa d. 193.56 kPaa a. 118.06 kW c. 181.06 kW
This study source was downloaded by 100000889195261 from CourseHero.com on 08-11-2024 00:55:19 GMT -05:00

https://www.coursehero.com/file/106114580/PIPE-1-QUESTIONNAIREdocx/
 b. 110.86 kW d. 168.01 Kw b. 0.579 d. 0.306
46. A pump draws water at a head of 110 m and a
37. The percent rating of water tube boiler is 200 %,
discharge rate of 550 lps. Determine the brake
factor of evaporation is 1.10, and heating surface is
power input if the pump efficiency is 70 %.
400 ft2. Determine the rate of evaporation, in kg/hr.
a. 1831 c. 1831 a. 847.57 kW c. 874.57 kW
b. 1138 d. 1813 b. 875.74 kW d. 854.75 kW
47. A turbine has a peripheral coefficient of 0.6. Find
38. A boiler operates at 82.5 % efficiency while the the runner diameter of the turbine if it operates at
mass of steam generated is 408 200 kg in 5 hours. 450 rpm and a head of 60 m.
The enthalpy of steam is 3187 kJ/kg and feed is a. 0.874 m c. 0.784 m
604.83 kJ/kg while the fuel used for boiler has a b. 0.478 m d. 0.748 m
heating value of 32 567.85 kJ/kg. Find the mass of
48. A 5 m x 5 m wall of a room has a surface
fuel needed per day in metric tons.
temperature of 40 oC. The wall thickness is 25 cm
a. 188.3 c. 183.8
and has a thermal conductivity of 0.07 W/m- oK,
b. 138.8 d. 318.8
and air film conductance is 15 W/m 2-oK. If the
39. A 10 kg/s of air enters the theater at 16 oC. The
outside air temperature is 18 oC, what is the heat
theater is to be maintained at 27 oC DB and 20 oC
loss through the wall?
WB. If the sensible heat ratio is 0.80, what is the
a. 151.18 W c. 185.18 W
latent heat load of the theater?
b. 158.11 W d. 118.15 W
a. 27.67 kW c. 26.75 kW
49. An air compressor operates with discharge
b. 110.682 kW d. 72.67 kW
pressure of 6 times the suction pressure. If the
40. Determine the mole fraction of the helium in a
volume flow rate at the suction is 0.8 m 3/s and the
mixture of 45 % helium and 55 % nitrogen by mass
compression process is in accordance with pV1.38 =
analysis.
C, determine the compressor power, in kW.
a. 14.84 % c. 85.16%
a. 187.16 kW c. 178.16 kW
b. 18.44 % d. 81.56 %
b. 167.18 kW d. 168.17 kW
41. A 60 MW power plant has an average load of 34
50. A horizontal pipe carries oil with a specific gravity
500 kW and a load factor of 0.75. Find the reserve
of 0.83. If two pressure gauges along the pipe read
power over a peak load power.
515 kPa and 430 kPa, respectively. Determine the
a. 14 000 kW c. 20 000 kW
head loss between the two gauges.
b. 46 000 kW d. 5 000 kW
a. 10.44 m c. 14.40 m
42. A steam generator burns fuel oil with 20 % excess
b. 14.04 m d. 40.14 m
air. Fuel may be represented by C14H30. Calculate o o
51. Air at 33 C DB and 19 C WB is cooled and
the actual-air fuel ratio.
humidified by passing through an air washer in
a. 17.9 c. 18.7
which water is continuously recirculated. The air
b. 16.7 d. 15.7
leaves the air washer at 23 oC DB. What is the
43. A certain coal has the following ultimate analysis by
efficiency of the air washer?
weight. C = 67 %, Ash = 5 %, Moisture = 8 %, N = 6
a. 71.43 % c. 73.41 %
%, H = 3 %, Sulfur = 7 %, O = 4 %. Calculate the air-
b. 74.31 % d. 73.14 %
fuel ratio if this coal is burned with 50 % excess air.
52. Determine the indicated power of a four-cylinder,
a. 12.4 c. 13.3
4-stroke, Diesel engine with 20-cm bore and 30-cm
b. 14.3 d. 12.4
stroke running at 1000 rpm and has a reading of
44. A container filled with helium is dropped 4 km
450 kPa mean effective pressure in the indicator
above the ground, find the change of temperature?
diagram.
a. 12.6 oC c. 17.5
a. 159.83 Hp c. 189.53 Hp
b. 15.2 oC d. 18.5 oC
b. 158.93 Hp d. 198.53 Hp
45. 2.5 m3/s of humid air at a state of 28°C DB, 21 WB
53. The approach and efficiency of cooling tower are
and 101.325 Kpaa flow across a cooler coil and
10 oC and 65 %, respectively. If the temperature of
leaves at 12.5°C DB and 0.0083 kg vapor per kg dry
water leaving the tower is 27 oC, determine the
air. If the apparatus dew point (ADP) is 8.5,
temperature of water entering the tower.
compute for the contact factor (CF). o
a. 54.57
This study source was downloaded by 100000889195261 from CourseHero.com on 08-11-2024 00:55:19 C
GMT -05:00 c. 55.47 oC
a. 0.835 c. 0.795

https://www.coursehero.com/file/106114580/PIPE-1-QUESTIONNAIREdocx/
 b. 45.57 oC d. 54.75 oC b. 4.55 % d. 5.65 %
54. If the sensible heat ratio is 0.80 and the cooling 62. In an air-standard Brayton cycle, air enters
load is 100 kW, what is the amount of sensible compressor at 1 bar and 15 oC. The pressure
heat? leaving the compressor is 0.6 MPaa and maximum
a. 100 kW c. 125 kW temperature of the cycle is 1000 oC. Calculate the
b. 80 kW d. 60 kW cycle thermal efficiency.
55. A dryer is to deliver 1000 kg/hr of cassava with 2 % a. 35 % c. 32 %
moisture and 20 % moisture in the feed. Determine b. 37.5 % d. 40 %
the mass of air required per hour if the change in 63. Liquid ammonia at a temperature of 26 oC is
humidity ratio is 0.0165. available at the expansion valve. The temperature
a. 16 136.36 kg/hr c. 13 636.36 kg/hr of the vaporizing ammonia in the evaporator is 2
o
b. 13 163.63 kg/hr d. 16 336.63 kg/hr C. Find the percentage of liquid vaporized while
56. The change of enthalpy in an air conditioning unit flowing through the expansion valve. Properties of
is 23.5 kJ/kg. The mass of supply air is 68000 kg/hr. refrigerant: At t = 2 oC, hf = 190.4 kJ/kg and hg =
What is the conditioner capacity, in TR? 1445.6 kJ/kg; At 26 oC, hf = 303.6 kJ/kg and hg =
a. 126.21 TR c. 125.26 TR 1465.6 kJ/kg.
b. 162.25 TR d. 152.26 TR a. 10.2 % c. 9.02 %
57. A DC motor driven pump running at 100 rpm b. 11.02 % d. 12.02 %
delivers 30 lps of water against a total pumping 64. An ideal dual combustion cycle operates on 0.45 kg
head of 27 m with a pump efficiency of 60 %. What of air. At the beginning of compression, the air is 97
speed would result if the pump rpm is increased to kPaa, 43 oC. Let rp = 1.5, rc = 1.6, and rk = 11.
a pumping head of 36 m assuming no change in Determine the percent clearance.
efficiency? a. 10 % c. 11 %
a. 115.47 rpm c. 114.57 rpm b. 9 % d. 12.56 %
b. 117.54 rpm d. 114.75 rpm 65. An ideal dual combustion cycle operates on 0.45 kg
58. A mechanical draft cooling tower cools the cooling of air. At the beginning of compression, the air is 97
water from 60°C to 25°C at the rate of 8 kg/sec. kPaa, 43 oC. Let rp = 1.5, rc = 1.6, and rk = 11.
Atmospheric air enters the tower at a state of 20°C Determine the thermal efficiency.
DB and 16°C WB. The air leaves the tower at 35°C. a. 58.7 % c. 57.8 %
What is the temperature of approach? b. 48.7 % d. 68.7 %
a. 9°C c. 6°C 66. In an air standard Otto cycle, the clearance volume
b. 8°C d. 35°C is 18 % of the displacement volume. Find the
59. In a geothermal power plant, the enthalpies of the thermal efficiency.
ground water and the turbine inlet are 1500 kJ/kg a. 52 % c. 53 %
and 3500 kJ/kg respectively. If the enthalpy of the b. 55 % d. 60 %
hot water in the flash tank is 700 kJ/kg and the 67. Helium is used in a Carnot engine where the
mass flow rate of steam is 15 kg/s, what is the volumes beginning with the constant temperature
mass flow rate of ground water? heat addition are V1 = 0.3565 m3, V2 = 0.5130 m3, V3
a. 52.5 kg/s c. 55.2 kg/s = 8.0 m3, and V4 = 5.57 m3. Determine the thermal
b. 25.5 kg/s d. 35.2 kg/s efficiency if k = 1.666.
60. 12 kg of gas with a molecular mass of 30 at a. 83.95 % c. 89.35 %
101.325 kPaa pressure and 30 oC temperature b. 85.93 % d. 85.39 %
occupies a volume of 9500 liters. Determine the 68. Determine the equivalence ratio of the following
compressibility factor. mixture: 4 grams of butane, C4H10, and 75 grams of
a. 0.955 c. 0.595 air.
b. 0.795 d. 0.895 a. 0.72 c. 0.92
61. A refrigeration compressor has a specific volume of b. 0.62 d. 0.82
3 3
0.0482 m /kg at entrance and 0.017 m /kg at the 69. A hydraulic turbine receives water from a reservoir
exit. If volumetric efficiency is 90 %, determine the at an elevation of 100 m above it. What is the
percent clearance of the compressor. minimum water flow in kg/s to produce a steady
This a. 5.45
study % was downloaded by 100000889195261
source c. 5.54 %from CourseHero.com on 08-11-2024 00:55:19
turbine output of 50 MW?
GMT -05:00

https://www.coursehero.com/file/106114580/PIPE-1-QUESTIONNAIREdocx/
 a. 51 000 c. 15 000 78. It is the generic term given to a family of solid fuels
b. 50 100 d. 50 010 with high carbon content. How do you call this
70. An ideal vapor compression cycle requires 2.5 kW a. Solid fuel c. Coal
to power the compressor. You have found the b. Anthracite d. Bituminous
following data for the cycle: the enthalpy at the 79. Pressure drop caused by friction in fully developed
condenser entrance = 203 kJ/kg, exit = 55 kJ/kg; fluid flow can be determined directly using which
and evaporator entrance = 55 kJ/kg, exit = 178 of the following?
kJ/kg. If the mass flow rate of the refrigerant is 0.10 a. Computational fluid dynamics
kg/s, what is the coefficient of performance of the b. The Bernoulli’s equation
system? c. The Darcy-Weisbach equation
a. 9.42 c. 4.92 d. The first law of thermodynamics
b. 4.5 d. 2.94 80. The existing 2000 TR chiller at a large hospital,
71. A 100 TR system is used to produce chilled water where you are assigned as Engineer, must be
from 22 C to 2 C. Determine the volume flow rate replaced. Which of the following types most likely
of water in lps. to be installed?
a. 3.2 lps c. 4.2 lps a. Screw chiller c. Scroll Chiller
b. 3.8 lps d. 4.8 lps b. Reciprocating chiller d. Centrifugal chiller
72. A refrigeration system operates on the reversed 81. Which of the following parameters has the greatest
Carnot cycle. The minimum and maximum limiting effect on the thermal performance of an
temperatures are – 25 oC and 72 oC, respectively. If open, evaporative cooling tower?
the heat rejected at the condenser is 6000 kJ/min, a. Wet-Bulb temperature
determine the power input required. b. Dry-Bulb temperature
a. 1686.83 kJ/min c. 1668.83 kJ/min c. Range
b. 1866.83 kJ/min d. 1683.68 kJ/min d. Approach
73. Determine the brake power of the engine having a 82. The amount of heat required melting a ton (2000
brake thermal efficiency of 35 % and uses 25 oAPI lbs) of ice at 32°F, 288,000 Btu/24 hr, 12,000
fuel with fuel consumption of 40 kg/hr. Btu/hr, or 200 Btu/min.
a. 160.67 kW c. 173.52 kW a. KW of Refrigeration c. Tons of
b. 174.52 kW d. 165.84 kW Refrigeration
74. A refrigeration compressor has a specific volume of b. Refrigerating Effect d. Latent Heat
0.0482 m3/kg at entrance and 0.017 m3/kg at the 83. It is the temperature of vapor refrigerant above its
exit. If volumetric efficiency is 90 %, determine the saturation temperature corresponding to the given
percent clearance of the compressor. pressure.
a. 5.45 % c. 5.54 % a. Saturated c. Superheat
b. 4.55 % d. 5.65 % b. Subcooled d. Absolute
75. In a Carnot cycle, heat addition occurs during 84. What is the chemical name of R-23?
which of the following processes? a. Trifluoromethane
a. Isothermal compression process b. Dichlorofluoromethane
b. Isentropic expansion process c. Dichlorotetrafluoroethane
c. Isothermal expansion process d. Trichlorofluoromethane
d. Isentropic compression process 85. In a vapor-compression refrigeration system,
76. Stirling cycle is also called as: evaporator is a component normally called as:
a. Constant volume regenerative cycle a. High-pressure vapor heat exchanger
b. Constant pressure regenerative cycle b. Low-pressure heat exchanger
c. Constant temperature regenerative cycle c. Throttling device
d. Constant entropy regenerative cycle d. Pressure-raising device
77. Ericson cycle is also called as: 86. It is a component in the refrigeration system that
a. Constant volume regenerative cycle returns the lubricating oil, carried over by the
b. Constant pressure regenerative cycle refrigerant vapors, to the compressor. How do you
c. Constant temperature regenerative cycle call this component?
This d. Constant
study source wasentropy regenerative
downloaded cyclefrom CourseHero.com on 08-11-2024 00:55:19
by 100000889195261 a. Liquid receiver
GMT -05:00 c. Oil separator

https://www.coursehero.com/file/106114580/PIPE-1-QUESTIONNAIREdocx/
 b. Accumulator d. Capillary tube b. Zero d. Below zero
87. It is a boiler fuel created from the residue produced 97. The thermal efficiency of Stirling cycle is the same
from crude petroleum after it has been distilled to as the efficiency of which of the following cycles?
produce lighter oils like gasoline, paraffin, a. Otto cycle c. Brayton cycle
kerosene, diesel or gas oil. What is this fuel? b. Carnot cycle d. Dual cycle
a. Oil c. Kerosene 98. The ratio of the actual velocity to the sound
velocity.
b. Coke d. Peat
a. Prandtl Number c. Isottop number
88. What do you call a form of boiler fuel that is easy
b. Mach number d. Torecelli’s number
to burn, with very little excess air? 99. A fluid flowing in a reversible adiabatic
a. Coal c. Oil deceleration process to zero velocity will reach a
b. Gas d. Bunker state known as:
89. It defined as energy added to or removed from a a. Isentropic expansion
system divided by the mean absolute temperature b. Isentropic compression
over which the change takes place. How do you call c. Adiabatic irreversibility
this? d. Isentropic Stagnation
a. Enthalpy c. Heat energy 100. As a general rule, the cooling water side of
b. Specific heat d. Entropy the condenser should be scheduled for inspection
90. The second law of thermodynamics says that every which of the following number of months?
whenever energy is exchanged or converted from a. Every Month c. 3 Months
b. 6 Months d. 4 Months
one form to another, the potential for energy to do
work will be _________.
a. Decreased c. Increased
b. Zero d. Stagnant
91. What is a frictional force that acts parallel but
opposite to the direction of motion of fluid?
a. Drag c. Lift
b. Aero horsepower d. Terminal velocity
92. It is a humidity sensor used to measure relative
humidity, dew point, or absolute humidity of
ambient or moving air. This device could be
mechanical or electronic. How do you call this?
a. Hydrometer c. Hygrometer
b. Psychrometer d. Barometer
93. It is an upward force that is exerted on an object
(like flat plate, airfoil, rotating cylinder, etc.) as the
object passes through a fluid. What do you call
this?
a. Drag c. Lift
b. Aero horsepower d. Terminal velocity

94. The ratio of the actual water vapor pressure of the

air to the saturated water vapor pressure of the air
at the same temperature is known as:
a. Relative humidity c. Humidity ratio
b. Specific humidity d. Percent humidity
95. The weight of water vapor in grains, pounds,
grams, or kilograms per grain, pound, gram, or
kilogram of dry air.
a. Relative humidity c. Specific volume
b. Specific humidity d. Percent humidity
96. At critical point of a pure substance, what is the
value of latent heat?
This study source was downloaded by 100000889195261 from CourseHero.com on 08-11-2024 00:55:19 GMT -05:00
a. Maximum c. Minimum
https://www.coursehero.com/file/106114580/PIPE-1-QUESTIONNAIREdocx/
Powered by TCPDF (www.tcpdf.org)