0% found this document useful (0 votes)
429 views9 pages

Development of Surfaces Solution

DOS

Uploaded by

saravananms
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
429 views9 pages

Development of Surfaces Solution

DOS

Uploaded by

saravananms
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

SVCE Mechanical Engg Dept ECE A

A.KUMARASWAMY. AP, MECH

A Rectangular prism of cross section 45 X 30 mm and height 55 mm rests


on the ground on one of its ends with one of its longer edges of the base
inclined at 300 to the VP. It is cut by a plane perpendicular to VP and
inclined at 300 to the HP. The cutting plane meets the axis at a point 45
mm above the base. Draw the development of the surface of the lower
part of the prism.

A.KUMARASWAMY. AP, MECH

A Hexagonal prism of side 30 mm and axis length 60 mm is resting


on HP on its base with two of its vertical faces perpendicular to VP.
It is cut by a plane inclined at 500 to HP and perpendicular to VP
and meets the axis of prism at a distance of 10mm from the top
end. Draw the development of the lateral surface of the prism.

Tutorial Solutions- 2015 154


SVCE Mechanical Engg Dept ECE A

A.KUMARASWAMY. AP, MECH

3 A Pentagonal prism of base side 30mm and axis length 60mm is resting on HP on its base with a side of
base parallel to VP. It is cut by a plane inclined at 350 to HP and perpendicular to VP and meets the axis at
a distance of 35 mm from the base. Draw the development of the lower portion of the prism.

A.KUMARASWAMY. AP, MECH

A Cylinder of base diameter 50 mm and axis length 65 mm resting


on HP on its base is cut by a plane inclined at 600 to HP and
perpendicular to VP. The cutting plane passes through a point on
the axis at a distance of 25 mm from the top end. Draw the
development of the lateral surface of the right portion of the
cylinder

Tutorial Solutions- 2015 155


SVCE Mechanical Engg Dept ECE A

A.KUMARASWAMY. AP, MECH

5 A Cylinder of diameter 50 mm and axis height 65 mm is cut by a plane perpendicular to VP and inclined at
60° to the HP into two equal parts. Draw the development of the lateral surface of the truncated solid.

A.KUMARASWAMY. AP, MECH

6 A rectangular pyramid 60 mm x 50 mm and height 75 mm is


resting on its base on HP with its longer base edges parallel to
VP. It is sectioned by a plane perpendicular to VP, inclined at 65°
to HP and passing through the mid-point of the axis. Develop the
lateral surfaces of the cut pyramid

Tutorial Solutions- 2015 156


SVCE Mechanical Engg Dept ECE A

A.KUMARASWAMY. AP, MECH

7 A Hexagonal pyramid of base side 25 mm and altitude 50 mm is


resting vertically on its base on the ground with two of the side
of the base perpendicular to the VP. It is cut by a plane
perpendicular to VP and inclined at 400 to the HP. The cutting
plane bisects the axis of the pyramid. Draw the development of
the lateral surfaces of the pyramid.

A.KUMARASWAMY. AP, MECH

30

A regular pentagonal pyramid of side 40 mm and altitude 75 mm has its base


on HP with a side of base perpendicular to VP. The pyramid is cut by a section
plane perpendicular to VP and inclined at 300 to the HP. The cutting plane
meets the axis of the pyramid at a point 30 mm below the vertex. Obtain the
development of the remaining part of the pyramid.

Tutorial Solutions- 2015 157


SVCE Mechanical Engg Dept ECE A

A.KUMARASWAMY. AP, MECH

A right circular cone of base diameter 60 mm and height 70 mm is resting on its base on the
ground. It is cut by a plane inclined at 300 to HP and perpendicular to VP. The cutting plane
bisects the axis of the cone. Draw the development of the lateral surface of the truncated
cone.

A.KUMARASWAMY. AP, MECH

Tutorial Solutions- 2015 158


SVCE Mechanical Engg Dept ECE A

A.KUMARASWAMY. AP, MECH

10

A Cone of base diameter 60 mm and height 70 mm is resting on its base on the ground. It is
cut by a plane perpendicular to the VP and parallel to the HP at a distance of 20 mm from
the vertex. It is also cut by a plane inclined at 400 to the base and meeting the axis at a
point 20 mm above the base. Draw the development of the lateral surface of the cut cone.

A.KUMARASWAMY. AP, MECH

10

Tutorial Solutions- 2015 159


SVCE Mechanical Engg Dept ECE A

A.KUMARASWAMY. AP, MECH

11

A Pentagonal prism of base side 25 mm and height 60 mm stands on


one of its ends on the HP with a rectangular face parallel to the VP.
A hole of diameter 30 mm is drilled centrally through the prism in
such a way that the axis of the hole bisects the axis of the prism at
right angles. The axis of the hole is perpendicular to the VP. Draw
the development of the lateral surfaces of the prism.

A.KUMARASWAMY. AP, MECH

12 A Square pyramid of base side 35 mm and axis 60 mm rests on its


base on the HP with one of the sides of the base inclined at 300 to
the VP. A string is wound round the surfaces of the pyramid starting
from left extreme point on the base and ending at the same point.
Find the shortest length of the string required. Also trace the path
of the string in the front and top views.

Tutorial Solutions- 2015 160


SVCE Mechanical Engg Dept ECE A

A.KUMARASWAMY. AP, MECH

13 A cone of base diameter 60 mm and height 70 mm rests vertically on


its base on the ground. A string is wound round the curved surface
of the cone starting from the left extreme point on the base and
ending at the same point. Find the shortest length of the string
required. Also, trace the path of the string in the front and the top
views.

A.KUMARASWAMY. AP, MECH

14
A Cone of base diameter 60 mm and axis height 70 mm is
resting on the HP on its base. It is cut by a plane
perpendicular to both HP and VP, 10 mm away from the axis.
Draw the development of lateral surfaces

Tutorial Solutions- 2015 161


SVCE Mechanical Engg Dept ECE A

A.KUMARASWAMY. AP, MECH

15 A right regular Hexagonal pyramid of 30 mm side of base and height


70mm stands with its base on HP. A through circular hole of 30 mm
diameter is drilled through the pyramid such that the axis of the
hole is perpendicular to VP and intersects the axis of the pyramid at
a distance of 20 mm above the base. Draw the development of the
lateral surface of the pyramid showing the true shapes of the holes
formed on it.

A.KUMARASWAMY. AP, MECH

16

A Funnel tapers from a circular opening of diameter 70 mm to a circular opening of


diameter 20 mm over an axial length of 50 mm and extends axially to a further
distance of 40 mm. There is a cylindrical portion of height 15 mm above the
tapering portion. Develop the funnel.

Tutorial Solutions- 2015 162

You might also like