A330

SERVICE BULLETIN

CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE

The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.

MANDATORY MANDATORY MANDATORY

ATA SYSTEM: 27

TITLE: FLIGHT CONTROLS - TRIMMABLE HORIZONTAL STABILIZER (THS)

HYDRAULIC ACTUATION - INTRODUCE WIRING PROVISION FOR LOAD
SENSING DEVICE (LSD) RETROFIT
MODIFICATION No.:
CONF 001 005
208458S34974
CONF 002-004
208459S34991

REV 00 Oct 12/20 A330-27-3237

Page 1
 A330
SERVICE BULLETIN
SUMMARY
ATA SYSTEM: 27

TITLE: FLIGHT CONTROLS - TRIMMABLE HORIZONTAL STABILIZER (THS)

HYDRAULIC ACTUATION - INTRODUCE WIRING PROVISION FOR LOAD
SENSING DEVICE (LSD) RETROFIT
CONF ALL
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
CONF 001

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 208458S34974

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.

CONF 002

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 208459S34991

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.

CONF 003

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 208459S34991

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

REV 00 Oct 12/20 A330-27-3237

Page 2
 A330
SERVICE BULLETIN
SUMMARY
NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.

CONF 004

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 208459S34991

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.

CONF 005

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 208458S34974

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.

CONF ALL
B. REASON

(1) History
The Trimmable Horizontal Stabilizer (THS) actuator has a fail-safe design: each
attachment, upper and lower, has two load paths. A normally loaded primary load
path and a secondary load path, which is only engaged in case of primary load path
rupture.
When the secondary load path is engaged, the design purpose was to generate a
stall of the unit by friction and to detect it by the position monitoring. It has been
demonstrated by test that the upper secondary load path does not stall correctly.
Hence a new device has been developed, called Load Sensing Device (LSD),
manufactured by COLLINS Aerospace, which lead to detect the THS actuator upper
secondary load path engagement.
The wiring provisions for the connection of the LSD in production are introduced
through MOD No. 205978S33729.
(2) Objective/Action
This Service Bulletin recommends installing the wiring provisions for the LSD.

REV 00 Oct 12/20 A330-27-3237

Page 3
 A330
SERVICE BULLETIN
SUMMARY
It implies:

- The installation of specific secure open Circuit Breaker (59CS) on the 309PP in
the Auxillary Power Unit (APU) Starter Box (5000VE)
- To modify associated electrical and mechanical installation running from the
Circuit Breaker (C/B) 59CS into the THS actuator, zone 312.
(3) Advantages
Accomplishment of this Service Bulletin in conjunction with the Service Bulletin No.
Ref. SB A330-27-3234 will allow immediate detection in case of upper secondary load
path engagement. The periodic detailed inspection of THS actuator upper attachments
for secondary load path loading will however remain in order to ensure that remote
cases of partial loading are also detected.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION

EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING NO
A/C OPERATION NO VENDOR SB NO
AFFECTED
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO

NOTE: Service Bulletin must be accomplished.

D. MAINTENANCE CONFIGURATION
CONF 001
No specific aircraft maintenance configuration required.
CONF 002
No specific aircraft maintenance configuration required.
CONF 003
No specific aircraft maintenance configuration required.
CONF 004
No specific aircraft maintenance configuration required.
CONF 005
No specific aircraft maintenance configuration required.
CONF ALL
E. MATERIAL PRICE INFORMATION
CONF 001
(1) Modification

REV 00 Oct 12/20 A330-27-3237

Page 4
 A330
SERVICE BULLETIN
SUMMARY
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

MATERIAL PRICE INFORMATION TABLE

QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 273237D01R02 1 8500.00 USD Brackets, fasteners, angle,
harness, connectors
Part kit 273237D05R02 1 380.00 USD Circuit breaker, fasteners,
shunt
Part kit 273237D09R02 1 10500.00 USD Clamps, fasteners
TOTAL 19380.00 USD
Components See SB See Note Placard Set

NOTE: Price information to be obtained from the given supplier.

CONF 002
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

MATERIAL PRICE INFORMATION TABLE

QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 273237D02R02 1 15000.00 USD Clamps, fasteners, brackets,
connectors
Part kit 273237D04R01 1 600.00 USD Brackets, fasteners
Part kit 273237D05R02 1 380.00 USD Circuit breaker, fasteners,
shunt
TOTAL 15980.00 USD
Components See SB See Note Placard Set

NOTE: Price information to be obtained from the given supplier.

CONF 003
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

MATERIAL PRICE INFORMATION TABLE

QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 273237D02R02 1 15000.00 USD Clamps, fasteners, brackets,
connectors
Part kit 273237D05R02 1 380.00 USD Circuit breaker, fasteners,
shunt
Part kit 273237D08R00 1 600.00 USD Brackets, fasteners
TOTAL 15980.00 USD
Components See SB See Note Placard Set

NOTE: Price information to be obtained from the given supplier.

REV 00 Oct 12/20 A330-27-3237

Page 5
 A330
SERVICE BULLETIN
SUMMARY
CONF 004
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

MATERIAL PRICE INFORMATION TABLE

QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 273237D02R02 1 15000.00 USD Clamps, fasteners, brackets,
connectors
Part kit 273237D03R01 1 770.00 USD Brackets, fasteners
Part kit 273237D05R02 1 380.00 USD Circuit breaker, fasteners,
shunt
TOTAL 16150.00 USD
Components See SB See Note Placard Set

NOTE: Price information to be obtained from the given supplier.

CONF 005
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

MATERIAL PRICE INFORMATION TABLE

QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 273237D01R02 1 8500.00 USD Brackets, fasteners, angle,
harness, connectors
Part kit 273237D06R04 1 370.00 USD Circuit breaker, fasteners,
shunt
Part kit 273237D07R03 1 10500.00 USD Clamps, fasteners
TOTAL 19370.00 USD
Components See SB See Note Placard Set

NOTE: Price information to be obtained from the given supplier.

CONF ALL
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
01V 09K 12P 18P 18Q 26L 34N 38W 39N 39V 41N 46L 46O 48L 57L 68M 72T 74K 77L 78X
82W 83Q 83V 86Z 90U 97X 98W 98X AAL AAR AAW ABD ABR ACA ACI AEA AFL AFR AHK AIB
ALK ARG ASL ASY AVA AWC AWW AZA AZU BCS BEC BEL CAL CBJ CCA CEB CES CHH CIL CPA
CRK CRL CSA CSC CSN CXB DAH DAL DGA DLH EDW EIN ETD EVA EVE F2I FAF FIN FJI FWI
G2X G8E GCR GFA GIA GJT GRL HAL HDA HFM HFY HKC IAW IBE IRA ISS JAI JAV KAC KAL KKK
KLM LAA LMU LNI MAS MAU MEA MNB MSR NCR NMB NWS OBS OHY OMA P2C PAL PLM QAF
QFA QTR RSF RSY RWD RZO SAA SAF SAS SEP SIA SVA SWR SXD TAP TAR TBA TCX THA THY
TOW TPA TSC U6A UAE UAF VIR VKG VOZ XAX XLF
G. CONCURRENT REQUIREMENTS
None

REV 00 Oct 12/20 A330-27-3237

Page 6
 A330
SERVICE BULLETIN
SUMMARY
H. NATURE OF THE WORK
CONF 001
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

AIRCRAFT YES
EQUIPMENT YES
CONF 002
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

AIRCRAFT YES
EQUIPMENT YES
CONF 003
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

AIRCRAFT YES
EQUIPMENT YES
CONF 004
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

AIRCRAFT YES
EQUIPMENT YES
CONF 005
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

AIRCRAFT YES
EQUIPMENT YES
CONF ALL
I. MANPOWER
CONF 001
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

MANPOWER
TOTAL MAN-HOURS 54.00 h
ELAPSED TIME (HOURS) 54.00 h
CONF 002
(1) Modification

REV 00 Oct 12/20 A330-27-3237

Page 7
 A330
SERVICE BULLETIN
SUMMARY
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

MANPOWER
TOTAL MAN-HOURS 54.00 h
ELAPSED TIME (HOURS) 54.00 h
CONF 003
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

MANPOWER
TOTAL MAN-HOURS 54.00 h
ELAPSED TIME (HOURS) 54.00 h
CONF 004
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

MANPOWER
TOTAL MAN-HOURS 54.00 h
ELAPSED TIME (HOURS) 54.00 h
CONF 005
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

MANPOWER
TOTAL MAN-HOURS 54.00 h
ELAPSED TIME (HOURS) 54.00 h

REV 00 Oct 12/20 A330-27-3237

Page 8
 A330
SERVICE BULLETIN
SUMMARY
CONF ALL
J. GENERAL OVERVIEW
CONF 001 005

Z310

FR91

FR87

FR86

FR85

FR84
5869VB /1MF
FR83
FR80 /82
5871VB /1M
5870VB /2MF

ICN-A330-A-27XX3237-A-FAPE3-0139P-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139P-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
General Overview
Page 9
 A330
SERVICE BULLETIN
SUMMARY
CONF 002-004

Z310

FR91

FR87
5871VB /1M
FR86
5870VB /2MF
FR85

FR84
5869VB /1MF FR83
FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-0139Q-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139Q-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
General overview
Page 10
 A330
SERVICE BULLETIN
SUMMARY
CONF ALL

MODIFICATION OF THE APU STARTER BOX

FR73

Z160

FR65

ICN-A330-A-27XX3237-A-FAPE3-013EP-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013EP-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
General overview
Page 11
 A330
SERVICE BULLETIN

ATA SYSTEM: 27

TITLE: FLIGHT CONTROLS - TRIMMABLE HORIZONTAL STABILIZER (THS)

HYDRAULIC ACTUATION - INTRODUCE WIRING PROVISION FOR LOAD
SENSING DEVICE (LSD) RETROFIT
1. PLANNING INFORMATION
A. APPLICABILITY

NOTE: These modifications are applicable by Service Bulletin only.

(1) Models
ON A/C 0211, 0269, 0272, 0330, 0339, 0397, 0441, 0473, 0487, 0489, 0506-0508, 0510,
0511, 0513, 0521, 0522, 0571, 0605, 0638, 0644, 0647, 0650, 0653, 0667, 0733, 0743,
0745, 0746, 0749, 0760, 0792, 0814, 0820, 0825, 0831, 0841, 0842, 0849, 0853, 0877,
0883, 0885, 0888, 0899, 0904, 0914, 0923, 0931, 0934, 0940, 0945, 0947, 0950, 0956,
0980, 0996, 1043, 1057, 1061, 1094, 1123, 1135, 1169, 1174, 1198, 1218, 1225, 1235,
1251, 1252, 1258, 1283, 1308, 1313, 1321, 1327, 1339, 1354, 1365, 1379, 1412, 1472,
1478, 1505, 1516, 1543, 1605, 1613, 1623, 1630, 1649, 1694, 1700, 1710, 1719, 1728,
1736, 1737, 1740, 1747, 1748, 1755, 1761, 1777, 1784
330-202
ON A/C 0422, 0443, 0448, 0458, 0463, 0465, 0466, 0472, 0477, 0481, 0486, 0498, 0500,
0502-0504, 0516, 0519, 0530, 0535, 0555, 0567, 0573, 0584, 0587, 0612, 0616, 0634, 0655,
0657, 0661, 0678, 0682, 0684, 0686, 0693, 0697, 0700, 0703, 0704, 0738, 0742, 0747,
0754, 0755, 0770, 0774, 0801, 0811, 0819, 0834, 0871, 0882, 0887, 0892, 0898, 0900,
0901, 0925, 0932, 0951, 0969, 0976, 1036, 1161, 1183
330-203
ON A/C 0181, 0195, 0222, 0223, 0226, 0229, 0230, 0240, 0249, 0253, 0255, 0258, 0262,
0275, 0288, 0290, 0291, 0296, 0300, 0305, 0308, 0312, 0317, 0322, 0324, 0343, 0353,
0358, 0362, 0364, 0366, 0403, 0432, 0444, 0454, 0469, 0476, 0493, 0609, 0614, 0618,
0620, 0621, 0631, 0633, 0665, 0718, 0722, 0739, 0778, 0796, 0802, 0822, 0828, 0869,
0874, 0876, 0891, 0911, 0927, 0939, 0943, 0946, 0949, 0961, 0962, 0968, 0970, 0977,
0979, 1002, 1019, 1031, 1034, 1039, 1042, 1054, 1059, 1096, 1112, 1116, 1118, 1129,
1133, 1155, 1200, 1202, 1203, 1213, 1220, 1221, 1233, 1244, 1256, 1266, 1297, 1309,
1335, 1393
330-223
ON A/C 1136, 1148, 1164, 1180
330-223F
ON A/C 0248, 0250, 0251, 0254, 0261, 0265, 0266, 0271, 0276, 0281, 0283, 0285-0287,
0293, 0295, 0301, 0303, 0306, 0309, 0311, 0313, 0314, 0316, 0320, 0326, 0328, 0334,
0340, 0345, 0348, 0365, 0369, 0372, 0382, 0384, 0392, 0396, 0398, 0401, 0404, 0409,
0427, 0437, 0451, 0452, 0455, 0456, 0461, 0462, 0480, 0491, 0494, 0501, 0505, 0509,
0518, 0525-0527, 0529, 0532, 0536, 0551, 0597, 0600, 0610, 0625, 0627, 0632, 0635, 0649,
0652, 0656, 0658, 0664, 0666, 0683, 0688, 0696, 0709, 0717, 0724, 0726, 0728-0730, 0732,
0735, 0737, 0750, 0751, 0756, 0759, 0780, 0785, 0788, 0795, 0797, 0807, 0809, 0810,
0815, 0818, 0821, 0824, 0832, 0839, 0840, 0852, 0854, 0860, 0863, 0867, 0868, 0873,
0875, 0881, 0884, 0890, 0903, 0906, 0909, 0916, 0919, 0926, 0930, 0941, 0944, 0948,
0957, 0963, 0966, 0967, 0971, 0973, 0975, 0982, 0984, 0988, 0991, 0992, 0995, 0998,
1008, 1009, 1011, 1014, 1016, 1020, 1022, 1028, 1033, 1038, 1041, 1045-1047, 1049, 1052,
1053, 1069, 1073, 1076, 1080, 1082, 1095, 1100, 1104, 1114, 1120, 1138, 1159, 1171,
1184, 1186, 1191, 1208, 1210, 1214, 1217, 1223, 1224, 1227, 1236, 1237, 1240, 1241,
1248-1250, 1259-1262, 1267, 1271, 1275, 1277, 1279, 1280, 1282, 1286, 1288, 1291, 1293,
1295, 1302-1304, 1306, 1310, 1312, 1316, 1319, 1322, 1324, 1330, 1331, 1334, 1342, 1363,
1364, 1372, 1375, 1389, 1390, 1394, 1396, 1399, 1400, 1402, 1404, 1407, 1410, 1415-1417,

REV 00 Oct 12/20 A330-27-3237

Page 12
 A330
SERVICE BULLETIN

1419, 1421, 1422, 1429, 1434, 1439-1441, 1444, 1451, 1452, 1455, 1459, 1461, 1465, 1466,
1468, 1469, 1471, 1474, 1479, 1480, 1484, 1486, 1488, 1492, 1496, 1498, 1500, 1502,
1508, 1511, 1512, 1520, 1521, 1526, 1530, 1537, 1540, 1547, 1555, 1558, 1561, 1565,
1569, 1573, 1586, 1588, 1591, 1601, 1603, 1606, 1608, 1610, 1615, 1617, 1626, 1631,
1639, 1641, 1643, 1653, 1655, 1657, 1662, 1664, 1667, 1672, 1676, 1678, 1681, 1725,
1730, 1732, 1735, 1741, 1746, 1751, 1756, 1758, 1762, 1771, 1773, 1775, 1780, 1782,
1785, 1787
330-243
ON A/C 1004, 1032, 1051, 1062, 1070, 1092, 1115, 1175, 1320, 1332, 1344, 1350, 1368,
1380, 1386, 1406, 1414, 1418, 1428, 1442, 1448, 1506, 1524, 1534, 1550, 1578, 1584,
1594, 1688, 1708, 1722, 1750, 1768, 1772
330-243F
ON A/C 0030, 0037, 0045, 0054, 0055, 0070, 0086, 0200
330-301
ON A/C 0602, 0607, 0623, 0637, 0641, 0659, 0671, 0675, 0680, 0691, 0699, 0707, 0711,
0714, 0721, 0725, 0734, 0752, 0769, 0789, 0805, 0813, 0823, 0826, 0838, 0847, 0861,
0893, 0907, 0918, 0920, 0985, 0994, 1007, 1013, 1023, 1025, 1067, 1078, 1088, 1106,
1173, 1177, 1254, 1268, 1272, 1274, 1278, 1346, 1351, 1361, 1367, 1370, 1377, 1385,
1391, 1405, 1426, 1437, 1450, 1490, 1499, 1507, 1515, 1535, 1539, 1627, 1628, 1637,
1679, 1684, 1690, 1701, 1716, 1720, 1721, 1742, 1744, 1767, 1769, 1778, 1783
330-302
ON A/C 0553, 0558, 0564, 0574, 0593, 0595, 0603, 0695, 0705, 0712, 1287, 1294, 1300,
1360, 1381, 1458, 1476, 1487, 1501, 1514, 1529, 1571, 1580, 1616, 1620, 1622, 1629,
1640, 1642, 1644, 1696, 1704, 1706, 1713, 1718
330-303
ON A/C 0050, 0060, 0062, 0065, 0112, 0122
330-321
ON A/C 0072, 0082, 0087, 0095, 0096, 0116, 0120, 0127, 0143, 0162, 0171, 0172, 0206,
0209, 0219, 0224, 0231, 0241
330-322
ON A/C 0256, 0267, 0315, 0323, 0333, 0337, 0338, 0342, 0346, 0350, 0351, 0368, 0370,
0375, 0380, 0388, 0425, 0428, 0484, 0490, 0524, 0533, 0542, 0549, 0550, 0552, 0578,
0588, 0591, 0640, 0663, 0674, 0676, 0690, 0708, 0758, 0772, 0784, 0799, 0803, 0806,
0817, 0827, 0843, 0845, 0857-0859, 0865, 0965, 1001, 1021, 1055, 1151, 1209, 1211, 1219,
1229, 1234, 1243, 1265, 1281, 1318, 1326, 1336, 1337, 1340, 1347, 1388, 1392, 1395,
1425, 1430, 1431, 1435, 1464, 1470, 1489, 1494, 1518, 1519, 1536, 1556, 1575, 1576,
1590, 1593, 1611, 1625, 1636, 1638, 1645, 1647, 1699, 1714, 1727, 1760, 1776
330-323
ON A/C 0138, 0140, 0144, 0148, 0153, 0165
330-341
ON A/C 0012, 0017, 0071, 0083, 0099, 0102, 0106, 0109, 0111, 0113, 0118, 0121, 0132,
0155, 0177, 0234, 0244, 0669, 0673, 0679, 0776, 0850, 0855, 0895, 0915, 0959, 1163
330-342
ON A/C 0277, 0279, 0284, 0344, 0349, 0356, 0357, 0386, 0389, 0393, 0400, 0405, 0407,
0408, 0412, 0418-0421, 0423, 0439, 0479, 0496, 0497, 0512, 0515, 0539, 0548, 0565, 0568,
0570, 0576, 0579, 0581, 0629, 0636, 0642, 0645, 0648, 0654, 0662, 0670, 0687, 0692,
0701, 0713, 0716, 0720, 0741, 0773, 0777, 0781, 0782, 0786, 0791, 0830, 0833, 0836,
0851, 0862, 0866, 0879, 0889, 0896, 0905, 0908, 0913, 0922, 0928, 0935-0937, 0942, 0952,
0954, 0958, 0964, 0974, 0978, 0983, 0986, 0989, 0990, 0997, 1000, 1003, 1006, 1010,
1012, 1015, 1018, 1026, 1029, 1035, 1037, 1044, 1048, 1058, 1060, 1063, 1065, 1066,
1071, 1072, 1074, 1075, 1077, 1081, 1084-1087, 1089, 1090, 1093, 1097-1099, 1101, 1103,
1105, 1107, 1108, 1110, 1124, 1126, 1127, 1130-1132, 1137, 1141, 1143, 1145-1147, 1149,
REV 00 Oct 12/20 A330-27-3237
Page 13
 A330
SERVICE BULLETIN

1150, 1153, 1156, 1157, 1160, 1165, 1167, 1168, 1170, 1172, 1178, 1181, 1187-1190, 1192,
1193, 1195, 1196, 1199, 1201, 1204-1206, 1212, 1215, 1216, 1222, 1226, 1228, 1230-1232,
1238, 1239, 1245-1247, 1255, 1263, 1264, 1269, 1270, 1276, 1284, 1285, 1289, 1290, 1292,
1296, 1298, 1299, 1301, 1305, 1307, 1311, 1314, 1315, 1317, 1323, 1325, 1328, 1329,
1333, 1338, 1341, 1343, 1345, 1348, 1349, 1352, 1353, 1355-1359, 1362, 1366, 1369, 1371,
1373, 1374, 1376, 1378, 1382-1384, 1387, 1397, 1398, 1401, 1403, 1408, 1409, 1411, 1413,
1420, 1423, 1427, 1432, 1433, 1436, 1438, 1443, 1445-1447, 1449, 1453, 1454, 1456, 1457,
1460, 1462, 1463, 1467, 1473, 1475, 1477, 1481-1483, 1485, 1491, 1493, 1495, 1497, 1503,
1504, 1509, 1510, 1513, 1517, 1523, 1525, 1527, 1528, 1531-1533, 1538, 1541, 1542, 1544-
1546, 1548, 1549, 1551-1554, 1557, 1559, 1560, 1562-1564, 1566-1568, 1570, 1572, 1574,
1577, 1579, 1581-1583, 1585, 1587, 1589, 1592, 1595-1600, 1602, 1604, 1607, 1609, 1612,
1614, 1618, 1619, 1621, 1624, 1632-1635, 1646, 1648, 1650, 1651, 1654, 1656, 1658-1660,
1663, 1665, 1666, 1668-1671, 1673-1675, 1677, 1680, 1685-1687, 1689, 1691-1693, 1695,
1697, 1698, 1703, 1709, 1711, 1712, 1715, 1723, 1724, 1726, 1729, 1731, 1733, 1734,
1738, 1739, 1743, 1745, 1749, 1752-1754, 1757, 1759, 1763-1766, 1770, 1774, 1779, 1781,
1786, 1788, 1789
330-343
CONF ALL
(2) Applicability by MSN
0012 0017 0030 0037 0045 0050 0054 0055 0060 0062 0065 0070-0072 0082 0083
0086 0087 0095 0096 0099 0102 0106 0109 0111-0113 0116 0118 0120-0122 0127
0132 0138 0140 0143 0144 0148 0153 0155 0162 0165 0171 0172 0177 0181 0195
0200 0206 0209 0211 0219 0222-0224 0226 0229-0231 0234 0240 0241 0244 0248-
0251 0253-0256 0258 0261 0262 0265-0267 0269 0271 0272 0275-0277 0279 0281
0283-0288 0290 0291 0293 0295 0296 0300 0301 0303 0305 0306 0308 0309 0311-
0317 0320 0322-0324 0326 0328 0330 0333 0334 0337-0340 0342-0346 0348-0351
0353 0356-0358 0362 0364-0366 0368-0370 0372 0375 0380 0382 0384 0386 0388
0389 0392 0393 0396-0398 0400 0401 0403-0405 0407-0409 0412 0418-0423 0425
0427 0428 0432 0437 0439 0441 0443 0444 0448 0451 0452 0454-0456 0458 0461-
0463 0465 0466 0469 0472 0473 0476 0477 0479-0481 0484 0486 0487 0489-0491
0493 0494 0496-0498 0500-0513 0515 0516 0518 0519 0521 0522 0524-0527 0529
0530 0532 0533 0535 0536 0539 0542 0548-0553 0555 0558 0564 0565 0567 0568
0570 0571 0573 0574 0576 0578 0579 0581 0584 0587 0588 0591 0593 0595 0597
0600 0602 0603 0605 0607 0609 0610 0612 0614 0616 0618 0620 0621 0623 0625
0627 0629 0631-0638 0640-0642 0644 0645 0647-0650 0652-0659 0661-0667 0669-
0671 0673-0676 0678-0680 0682-0684 0686-0688 0690-0693 0695-0697 0699-0701
0703-0705 0707-0709 0711-0714 0716-0718 0720-0722 0724-0726 0728-0730 0732-
0735 0737-0739 0741-0743 0745-0747 0749-0752 0754-0756 0758-0760 0769 0770
0772-0774 0776-0778 0780-0782 0784-0786 0788 0789 0791 0792 0795-0797 0799
0801-0803 0805-0807 0809-0811 0813-0815 0817-0828 0830-0834 0836 0838-0843
0845 0847 0849-0855 0857-0863 0865-0869 0871 0873-0877 0879 0881-0885 0887-
0893 0895 0896 0898-0901 0903-0909 0911 0913-0916 0918-0920 0922 0923 0925-
0928 0930-0932 0934-0937 0939-0952 0954 0956-0959 0961-0971 0973-0980 0982-
0986 0988-0992 0994-0998 1000-1004 1006-1016 1018-1023 1025 1026 1028 1029
1031-1039 1041-1049 1051-1055 1057-1063 1065-1067 1069-1078 1080-1082 1084-
1090 1092-1101 1103-1108 1110 1112 1114-1116 1118 1120 1123 1124 1126 1127
1129-1133 1135-1138 1141 1143 1145-1151 1153 1155-1157 1159-1161 1163-1165
1167-1175 1177 1178 1180 1181 1183 1184 1186-1193 1195 1196 1198-1206 1208-
1241 1243-1252 1254-1256 1258-1272 1274-1423 1425-1521 1523-1651 1653-1660
1662-1681 1684-1701 1703 1704 1706 1708-1716 1718-1789
(3) MSN by configuration
CONF 001

REV 00 Oct 12/20 A330-27-3237

Page 14
 A330
SERVICE BULLETIN

MSN CONFIGURATION
0181 0195 0200 0206 0209 0211 0219 0222 0223 0224 0226 001
0229 0230 0231 0234 0240 0241 0244 0248 0249 0250 0251
0253 0254 0255 0256 0258 0261 0262 0265 0266 0267 0269
0271 0272 0275 0276 0277 0279 0281 0283 0284 0285 0286
0287 0288 0290 0291 0293 0295 0296 0300 0301 0303 0305
0306 0308 0309 0311 0312 0313 0314 0315 0316 0317 0320
0322 0323 0324 0326 0328 0330 0333 0334 0337 0338 0339
0340 0342 0343 0344 0345 0346 0348 0349 0350 0351 0353
0356 0357 0358 0362 0364 0365 0366 0368 0369 0370 0372
0375 0380 0382 0384 0386 0388 0389 0392 0393 0396 0397
0398 0400 0401 0403 0404 0405 0407 0408 0409 0412 0418
0419 0420 0421 0422 0423 0425 0427 0428 0432 0437 0439
0441 0443 0444 0448 0451 0452 0454 0455 0456 0458 0461
0462 0463 0465 0466 0469 0472 0473 0476 0477 0479 0480
0481 0484 0486 0487 0489 0490 0491 0493 0494 0496 0497
0498 0500 0501 0502 0503 0504 0505 0506 0507 0508 0509
0510 0511 0512 0513 0515 0516 0518 0519 0521 0522 0524
0525 0526 0527 0529 0530 0532 0533 0535 0536 0539 0542
0548 0549 0550 0551 0552 0553 0555 0558 0564 0565 0567
0568 0570 0571 0573 0574 0576 0578 0579 0581 0584 0587
0588 0591 0593 0595 0597 0600 0602 0603 0605 0607 0609
0610 0612 0614 0616 0618 0620 0621 0623 0625 0627 0629
0631 0632 0633 0634 0635 0636 0637 0638 0640 0641 0642
0644 0645 0647 0648 0649 0650 0652 0653 0654 0655 0656
0657 0658 0659 0661 0662 0663 0664 0665 0666 0667 0669
0670 0671 0673 0674 0675 0676 0678 0679 0680 0682 0683
0684 0686 0687 0688 0690 0691 0692 0693 0695 0696 0697
0699 0700 0701 0703 0704 0705 0707 0708 0709 0711 0712
0713 0714 0716 0717 0718 0720 0721 0722 0724 0725 0726
0728 0729 0730 0732 0733 0734 0735 0737 0738 0739 0741
0742 0743 0745 0746 0747 0749 0750 0751 0752 0754 0755
0756 0758 0759 0760 0769 0770 0772 0773 0774 0776 0777
0778 0780 0781 0782 0784 0785 0786 0788 0789 0791 0792
0795 0796 0797 0799 0801 0802 0803 0805 0806 0807 0809
0810 0811 0813 0814 0815 0817 0818 0819 0820 0821 0822
0823 0824 0825 0826 0827 0828 0830 0831 0832 0833 0834
0836 0838 0839 0840 0841 0842 0843 0845 0847 0849 0850
0851 0852 0853 0854 0855 0857 0858 0859 0860 0861 0862
0863 0865 0866 0867 0868 0869 0871 0873 0874 0875 0876
0877 0879 0881 0882 0883 0884 0885 0887 0888 0889 0890
0891 0892 0893 0895 0896 0898 0899 0900 0901 0903 0904
0905 0906 0907 0908 0909 0911 0913 0914 0915 0916 0918
0919 0920 0922 0923 0925 0926 0927 0928 0930 0931 0932
0934 0935 0936 0937 0939 0940 0941 0942 0943 0944 0945
0946 0947 0948 0949 0950 0951 0952 0954 0956 0957 0958
0959 0961 0962 0963 0964 0965 0966 0967 0968 0969 0970
0971 0973 0974 0975 0976 0977 0978 0979 0980 0982 0983
0984 0985 0986 0988 0989 0990 0991 0992 0994 0995 0996
0997 0998 1000 1001 1002 1003 1006 1007 1008 1009 1010
1011 1012 1013 1014 1015 1016 1018 1019 1020 1021 1022
1023 1025 1026 1028 1029 1031 1033 1034 1035 1036 1037
1038 1039 1041 1042 1043 1044 1045 1046 1047 1048 1049
1052 1053 1054 1055 1057 1058 1059 1060 1061 1063 1065
1066 1067 1069 1071 1072 1073 1074 1075 1076 1077 1078
1080 1081 1082 1084 1085 1086 1087 1088 1089 1090 1093

REV 00 Oct 12/20 A330-27-3237

Page 15
 A330
SERVICE BULLETIN

MSN CONFIGURATION
1094 1095 1096 1097 1098 1099 1100 1101 1103 1104 1105
1106 1107 1108 1110 1112 1114 1116 1118 1120 1123 1124
1126 1127 1129 1130 1131 1132 1133 1135 1137 1138 1141
1143 1145 1146 1147 1149 1150 1151 1153 1155 1156 1157
1159 1160 1161 1163 1165 1167 1168 1169 1170 1171 1172
1173 1174 1177 1178 1181 1183 1184 1186 1187 1188 1189
1190 1191 1192 1193 1195 1196 1198 1199 1200 1201 1202
1203 1204 1205 1206 1208 1209 1210 1211 1212 1213 1214
1215 1216 1217 1218 1219 1220 1221 1222 1223 1224 1225
1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236
1237 1238 1239 1240 1241 1243 1244 1245 1246 1247 1248
1249 1250 1251 1252 1254 1255 1256 1258 1259 1260 1261
1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272
1274 1275 1276 1277 1278 1279 1280 1281 1282 1283 1284
1285 1286 1287 1288 1289 1290 1291 1292 1293 1294 1295
1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306
1307 1308 1309 1310 1311 1312 1313 1314 1315 1316 1317
1318 1319 1321 1322 1323 1324 1325 1326 1327 1328 1329
1330 1331 1333 1334 1335 1336 1337 1338 1339 1340 1341
1342 1343 1345 1346 1347 1348 1349 1351 1352 1353 1354
1355 1356 1357 1358 1359 1360 1361 1362 1363 1364 1365
1366 1367 1369 1370 1371 1372 1373 1374 1375 1376 1377
1378 1379 1381 1382 1383 1384 1385 1387 1388 1389 1390
1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401
1402 1403 1404 1405 1407 1408 1409 1410 1411 1412 1413
1415 1416 1417 1419 1420 1421 1422 1423 1425 1426 1427
1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439
1440 1441 1443 1444 1445 1446 1447 1449 1450 1451 1452
1453 1454 1455 1456 1457 1458 1459 1460 1461 1462 1463
1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474
1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485
1486 1487 1488 1489 1490 1491 1492 1493 1494 1495 1496
1497 1498 1499 1500 1501 1502 1503 1504 1505 1507 1508
1509 1510 1511 1512 1513 1514 1515 1516 1517 1518 1519
1520 1521 1523 1525 1526 1527 1528 1529 1530 1531 1532
1533 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544
1545 1546 1547 1548 1549 1551 1552 1553 1554 1555 1556
1557 1558 1559 1560 1561 1562 1563 1564 1565 1566 1567
1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1579
1580 1581 1582 1583 1585 1586 1587 1588 1589 1590 1591
1592 1593 1595 1596 1597 1598 1599 1600 1601 1602 1603
1604 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614
1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625
1626 1627 1628 1629 1630 1631 1632 1633 1634 1635 1636
1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647
1648 1649 1650 1651 1653 1654 1655 1656 1657 1658 1659
1660 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671
1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1684
1685 1686 1687 1689 1690 1691 1692 1693 1694 1695 1696
1697 1698 1699 1700 1701 1703 1704 1706 1709 1710 1711
1712 1713 1714 1715 1716 1718 1719 1720 1721 1723 1724
1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735
1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746
1747 1748 1749 1751 1752 1753 1754 1755 1756 1757 1758
1759 1760 1761 1762 1763 1764 1765 1766 1767 1769 1770

REV 00 Oct 12/20 A330-27-3237

Page 16
 A330
SERVICE BULLETIN

MSN CONFIGURATION
1771 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782
1783 1784 1785 1786 1787 1788 1789
CONF 002

MSN CONFIGURATION
0012 0017 0030 0037 0045 0050 0054 0055 0060 0062 0065 002
0070 0071 0072 0082 0083 0086 0087 0095 0096 0099 0102
0106 0109 0111 0112
CONF 003

MSN CONFIGURATION
0113 0116 0118 0120 0121 0122 0127 0132 0138 0140 0143 003
0144 0148 0153 0155
CONF 004

MSN CONFIGURATION
0162 0165 0171 0172 0177 004
CONF 005

MSN CONFIGURATION
1004 1032 1051 1062 1070 1092 1115 1136 1148 1164 1175 005
1180 1320 1332 1344 1350 1368 1380 1386 1406 1414 1418
1428 1442 1448 1506 1524 1534 1550 1578 1584 1594 1688
1708 1722 1750 1768 1772
CONF ALL
(4) Configuration definition
CONF 001
Configuration 001
CONF 001 regards the specific PRE-SB status of the related aircraft.
CONF 001 retrofits following modifications: 208458S34974.
CONF 002
Configuration 002
CONF 002 regards the specific PRE-SB status of the related aircraft.
CONF 002 retrofits following modifications: 208459S34991.
CONF 003
Configuration 003
CONF 003 regards the specific PRE-SB status of the related aircraft.
CONF 003 retrofits following modifications: 208459S34991.
CONF 004
Configuration 004
CONF 004 regards the specific PRE-SB status of the related aircraft.
CONF 004 retrofits following modifications: 208459S34991.
CONF 005

REV 00 Oct 12/20 A330-27-3237

Page 17
 A330
SERVICE BULLETIN

Configuration 005
CONF 005 regards the specific PRE-SB status of the related aircraft.
CONF 005 retrofits following modifications: 208458S34974.
CONF ALL
B. CONCURRENT REQUIREMENTS
None
C. REASON

(1) History
The Trimmable Horizontal Stabilizer (THS) actuator has a fail-safe design: each
attachment, upper and lower, has two load paths. A normally loaded primary load
path and a secondary load path, which is only engaged in case of primary load path
rupture.
When the secondary load path is engaged, the design purpose was to generate a
stall of the unit by friction and to detect it by the position monitoring. It has been
demonstrated by test that the upper secondary load path does not stall correctly.
Hence a new device has been developed, called Load Sensing Device (LSD),
manufactured by COLLINS Aerospace, which lead to detect the THS actuator upper
secondary load path engagement.
The wiring provisions for the connection of the LSD in production are introduced
through MOD No. 205978S33729.
(2) Objective/Action
This Service Bulletin recommends installing the wiring provisions for the LSD.
It implies:

- The installation of specific secure open Circuit Breaker (59CS) on the 309PP in
the Auxillary Power Unit (APU) Starter Box (5000VE)
- To modify associated electrical and mechanical installation running from the
Circuit Breaker (C/B) 59CS into the THS actuator, zone 312.
(3) Advantages
Accomplishment of this Service Bulletin in conjunction with the Service Bulletin No.
Ref. SB A330-27-3234 will allow immediate detection in case of upper secondary load
path engagement. The periodic detailed inspection of THS actuator upper attachments
for secondary load path loading will however remain in order to ensure that remote
cases of partial loading are also detected.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
To accomplish this Service Bulletin it is necessary to:
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD
CONF 001 005
1 Cut the Wire 2499-5020 in the Electrical Harness 5871VB
CONF 002-004

REV 00 Oct 12/20 A330-27-3237

Page 18
 A330
SERVICE BULLETIN

1 Cut the Wire 2499-5020 in the Electrical Harness 5871VB

CONF 001
2 Remove the Electrical Harness 5869VB from the Structure between FR86
and FR87 Traverse (with Loop-Clamps)
CONF 002-004
2 Remove the Electrical Harness 5869VB from the Structure between FR86
and FR87 V-Prop (with P-Clamps)
CONF 005
2 Remove the Electrical Harness 5869VB from the Structure between FR86
and FR87 Traverse (with P-Clamps)
CONF 001
3 Remove the Electrical Harness 5870VB from the structure between FR86
and FR87 Traverse (with Loop-Clamps)
CONF 002-004
3 Remove the Electrical Harness 5870VB from the structure between FR86
and FR87 V-Prop (with P-Clamps)
CONF 005
3 Remove the Electrical Harness 5870VB from the structure between FR86
and FR87 Traverse (with P-Clamps)
CONF 001 005
4 Modify the Traverse Structure at FR87
CONF 002
4 Modify the V-Prop Structure at FR87
CONF 003
4 Modify the V-Prop Structure at FR87
CONF 004
4 Modify the V-Prop Structure at FR87
CONF 001 005
5 Install the Brackets at FR87 Traverse
CONF 002-004
5 Install the Brackets at FR87 V-Prop
CONF 001 005
6 Install the Electrical Dummy Connectors at FR87 Traverse
CONF 002-004
6 Install the Electrical Dummy Connectors at FR87 V-Prop
CONF ALL
7 Reroute the Wire 2499-5020 between FR56 and FR69
CONF 001-004
8 Modify the C/B-Box 5000VE
CONF 005
8 Modify the C/B-Box 5000VE
CONF 001
9 Modify the Electrical Harness 5869VB
CONF 002-004
9 Modify the Electrical Harness 5869VB
CONF 005

REV 00 Oct 12/20 A330-27-3237

Page 19
 A330
SERVICE BULLETIN

9 Modify the Electrical Harness 5869VB

CONF 001 005
10 Modify the Electrical Harness 5870VB
CONF 002-004
10 Modify the Electrical Harness 5870VB
CONF 001
11 Reroute the cut wire
CONF 002-004
11 Reroute the cut wire
CONF 005
11 Reroute the cut wire
CONF 001
12 Install the Modified Electrical Harness 5869VB Traverse
CONF 002-004
12 Install the Modified Electrical Harness 5869VB V-Prop
CONF 005
12 Install the Modified Electrical Harness 5869VB Traverse
CONF 001
13 Install the Modified Electrical Harness 5870VB Traverse
CONF 002-004
13 Install the Modified Electrical Harness 5870VB V-Prop
CONF 005
13 Install the Modified harness 5870VB Traverse
CONF 001
14 Reroute the reidentified wire 2499-5020 to 5000VE
CONF 002-004
14 Reroute the reidentified wire 2499-5020 to 5000VE
CONF 005
14 Reroute the reidentified wire 2499-5020 to 5000VE
CONF ALL
E. COMPLIANCE

(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Aviation Safety Agency (EASA)
will be issued to confirm this classification. The accomplishment timescale, which has
not yet been defined, will be given in the AD.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
REV 00 Oct 12/20 A330-27-3237
Page 20
 A330
SERVICE BULLETIN

G. MANPOWER
CONF 001
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

PREPARATION
Job Set-up 1.00 h
Aircraft System Configuration 1.00 h
PROCEDURE
Cut the Wire 2499-5020 in the Electrical Harness 5871VB 1.00 h
Remove the Electrical Harness 5869VB from the Structure 2.00 h
between FR86 and FR87 Traverse (with Loop-Clamps)
Remove the Electrical Harness 5870VB from the structure 2.50 h
between FR86 and FR87 Traverse (with Loop-Clamps)
Modify the Traverse Structure at FR87 4.00 h
Install the Brackets at FR87 Traverse 3.00 h
Install the Electrical Dummy Connectors at FR87 Traverse 2.00 h
Reroute the Wire 2499-5020 between FR56 and FR69 1.00 h
Modify the C/B-Box 5000VE 4.00 h
Modify the Electrical Harness 5869VB 6.00 h
Modify the Electrical Harness 5870VB 9.00 h
Reroute the cut wire 1.00 h
Install the Modified Electrical Harness 5869VB Traverse 5.00 h
Install the Modified Electrical Harness 5870VB Traverse 6.00 h
Reroute the reidentified wire 2499-5020 to 5000VE 1.00 h
PREPARATION FOR TEST
Preparation for Test 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Close-up 3.00 h
TOTAL MAN-HOURS 54.00 h
ELAPSED TIME (HOURS) 54.00 h
CONF 002
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts

REV 00 Oct 12/20 A330-27-3237

Page 21
 A330
SERVICE BULLETIN

and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

PREPARATION
Job Set-up 1.00 h
Aircraft System Configuration 1.00 h
PROCEDURE
Cut the Wire 2499-5020 in the Electrical Harness 5871VB 1.00 h
Remove the Electrical Harness 5869VB from the Structure 2.00 h
between FR86 and FR87 V-Prop (with P-Clamps)
Remove the Electrical Harness 5870VB from the structure 2.50 h
between FR86 and FR87 V-Prop (with P-Clamps)
Modify the V-Prop Structure at FR87 4.00 h
Install the Brackets at FR87 V-Prop 3.00 h
Install the Electrical Dummy Connectors at FR87 V-Prop 2.00 h
Reroute the Wire 2499-5020 between FR56 and FR69 1.00 h
Modify the C/B-Box 5000VE 4.00 h
Modify the Electrical Harness 5869VB 6.00 h
Modify the Electrical Harness 5870VB 9.00 h
Reroute the cut wire 1.00 h
Install the Modified Electrical Harness 5869VB V-Prop 5.00 h
Install the Modified Electrical Harness 5870VB V-Prop 6.00 h
Reroute the reidentified wire 2499-5020 to 5000VE 1.00 h
PREPARATION FOR TEST
Preparation for Test 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Close-up 3.00 h
TOTAL MAN-HOURS 54.00 h
ELAPSED TIME (HOURS) 54.00 h
CONF 003
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

PREPARATION

REV 00 Oct 12/20 A330-27-3237

Page 22
 A330
SERVICE BULLETIN

Job Set-up 1.00 h

Aircraft System Configuration 1.00 h
PROCEDURE
Cut the Wire 2499-5020 in the Electrical Harness 5871VB 1.00 h
Remove the Electrical Harness 5869VB from the Structure 2.00 h
between FR86 and FR87 V-Prop (with P-Clamps)
Remove the Electrical Harness 5870VB from the structure 2.50 h
between FR86 and FR87 V-Prop (with P-Clamps)
Modify the V-Prop Structure at FR87 4.00 h
Install the Brackets at FR87 V-Prop 3.00 h
Install the Electrical Dummy Connectors at FR87 V-Prop 2.00 h
Reroute the Wire 2499-5020 between FR56 and FR69 1.00 h
Modify the C/B-Box 5000VE 4.00 h
Modify the Electrical Harness 5869VB 6.00 h
Modify the Electrical Harness 5870VB 9.00 h
Reroute the cut wire 1.00 h
Install the Modified Electrical Harness 5869VB V-Prop 5.00 h
Install the Modified Electrical Harness 5870VB V-Prop 6.00 h
Reroute the reidentified wire 2499-5020 to 5000VE 1.00 h
PREPARATION FOR TEST
Preparation for Test 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Close-up 3.00 h
TOTAL MAN-HOURS 54.00 h
ELAPSED TIME (HOURS) 54.00 h
CONF 004
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

PREPARATION
Job Set-up 1.00 h
Aircraft System Configuration 1.00 h
PROCEDURE
Cut the Wire 2499-5020 in the Electrical Harness 5871VB 1.00 h
Remove the Electrical Harness 5869VB from the Structure 2.00 h
between FR86 and FR87 V-Prop (with P-Clamps)

REV 00 Oct 12/20 A330-27-3237

Page 23
 A330
SERVICE BULLETIN

Remove the Electrical Harness 5870VB from the structure 2.50 h

between FR86 and FR87 V-Prop (with P-Clamps)
Modify the V-Prop Structure at FR87 4.00 h
Install the Brackets at FR87 V-Prop 3.00 h
Install the Electrical Dummy Connectors at FR87 V-Prop 2.00 h
Reroute the Wire 2499-5020 between FR56 and FR69 1.00 h
Modify the C/B-Box 5000VE 4.00 h
Modify the Electrical Harness 5869VB 6.00 h
Modify the Electrical Harness 5870VB 9.00 h
Reroute the cut wire 1.00 h
Install the Modified Electrical Harness 5869VB V-Prop 5.00 h
Install the Modified Electrical Harness 5870VB V-Prop 6.00 h
Reroute the reidentified wire 2499-5020 to 5000VE 1.00 h
PREPARATION FOR TEST
Preparation for Test 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Close-up 3.00 h
TOTAL MAN-HOURS 54.00 h
ELAPSED TIME (HOURS) 54.00 h
CONF 005
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

PREPARATION
Job Set-up 1.00 h
Aircraft System Configuration 1.00 h
PROCEDURE
Cut the Wire 2499-5020 in the Electrical Harness 5871VB 1.00 h
Remove the Electrical Harness 5869VB from the Structure 2.00 h
between FR86 and FR87 Traverse (with P-Clamps)
Remove the Electrical Harness 5870VB from the structure 2.50 h
between FR86 and FR87 Traverse (with P-Clamps)
Modify the Traverse Structure at FR87 4.00 h
Install the Brackets at FR87 Traverse 3.00 h
Install the Electrical Dummy Connectors at FR87 Traverse 2.00 h
Reroute the Wire 2499-5020 between FR56 and FR69 1.00 h

REV 00 Oct 12/20 A330-27-3237

Page 24
 A330
SERVICE BULLETIN

Modify the C/B-Box 5000VE 4.00 h

Modify the Electrical Harness 5869VB 6.00 h
Modify the Electrical Harness 5870VB 9.00 h
Reroute the cut wire 1.00 h
Install the Modified Electrical Harness 5869VB Traverse 5.00 h
Install the Modified harness 5870VB Traverse 6.00 h
Reroute the reidentified wire 2499-5020 to 5000VE 1.00 h
PREPARATION FOR TEST
Preparation for Test 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Close-up 3.00 h
TOTAL MAN-HOURS 54.00 h
ELAPSED TIME (HOURS) 54.00 h
CONF ALL
H. WEIGHT AND BALANCE
Not changed
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
CONF 001
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

AIRCRAFT MAINTENANCE MANUAL (AMM)

06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-801
Task 12-34-24-860-802 Task 20-21-11-911-801
Task 20-28-00-912-810 Task 21-26-00-710-803
Task 22-97-00-740-801 Task 24-41-00-861-801
Task 24-41-00-862-801
Task 25-53-00-000-801 Task 25-54-00-000-801
Task 25-53-00-400-801 Task 25-54-00-400-801
Task 27-44-51-400-801 Task 31-18-51-000-801
Task 31-18-51-400-801
Task 31-50-00-710-803 Task 31-60-00-710-802
Task 31-50-00-740-801
Task 33-14-00-710-801 Task 52-30-00-410-803
52-41-00, Page Block 001

REV 00 Oct 12/20 A330-27-3237

Page 25
 A330
SERVICE BULLETIN

AIRCRAFT WIRING MANUAL (AWM)

27-98-08

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)

20-33-00 20-33-42
20-33-44 20-43-12
20-51-20 20-52-10
20-52-21 20-54-50
20-55-00 20-56-51

SERVICE BULLETIN (SB)

A330-27-3234

STRUCTURAL REPAIR MANUAL (SRM)

51-24-00 51-40-00
51-42-00 51-44-00
51-75-12

TECHNICAL FOLLOW UP (TFU)

27.44.00.022
STANDARDS MANUAL (SM)
CONF 002
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

AIRCRAFT MAINTENANCE MANUAL (AMM)

06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-801
Task 12-34-24-860-802 Task 20-21-11-911-801
Task 20-28-00-912-810 Task 21-26-00-710-803
Task 22-97-00-740-801 Task 24-41-00-861-801
Task 24-41-00-862-801
Task 25-53-00-000-801 Task 25-54-00-000-801
Task 25-53-00-400-801 Task 25-54-00-400-801
Task 27-44-51-400-801 Task 31-18-51-000-801
Task 31-18-51-400-801
Task 31-50-00-710-803 Task 31-60-00-710-802
Task 31-50-00-740-801
Task 33-14-00-710-801 Task 52-30-00-410-803
52-41-00, Page Block 001

AIRCRAFT WIRING MANUAL (AWM)

27-98-08

REV 00 Oct 12/20 A330-27-3237

Page 26
 A330
SERVICE BULLETIN

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)

20-33-00 20-33-42
20-33-44 20-43-12
20-51-20 20-52-10
20-52-21 20-54-50
20-55-00 20-56-51

SERVICE BULLETIN (SB)

A330-27-3234

STRUCTURAL REPAIR MANUAL (SRM)

51-24-00 51-40-00
51-42-00 51-44-00
51-75-12

TECHNICAL FOLLOW UP (TFU)

27.44.00.022
STANDARDS MANUAL (SM)
CONF 003
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

AIRCRAFT MAINTENANCE MANUAL (AMM)

06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-801
Task 12-34-24-860-802 Task 20-21-11-911-801
Task 20-28-00-912-810 Task 21-26-00-710-803
Task 22-97-00-740-801 Task 24-41-00-861-801
Task 24-41-00-862-801
Task 25-53-00-000-801 Task 25-54-00-000-801
Task 25-53-00-400-801 Task 25-54-00-400-801
Task 27-44-51-400-801 Task 31-18-51-000-801
Task 31-18-51-400-801
Task 31-50-00-710-803 Task 31-60-00-710-802
Task 31-50-00-740-801
Task 33-14-00-710-801 Task 52-30-00-410-803
52-41-00, Page Block 001

AIRCRAFT WIRING MANUAL (AWM)

27-98-08

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)

20-33-00 20-33-42
20-33-44 20-43-12

REV 00 Oct 12/20 A330-27-3237

Page 27
 A330
SERVICE BULLETIN

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)

20-51-20 20-52-10
20-52-21 20-54-50
20-55-00 20-56-51

SERVICE BULLETIN (SB)

A330-27-3234

STRUCTURAL REPAIR MANUAL (SRM)

51-24-00 51-40-00
51-42-00 51-44-00
51-75-12

TECHNICAL FOLLOW UP (TFU)

27.44.00.022
STANDARDS MANUAL (SM)
CONF 004
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

AIRCRAFT MAINTENANCE MANUAL (AMM)

06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-801
Task 12-34-24-860-802 Task 20-21-11-911-801
Task 20-28-00-912-810 Task 21-26-00-710-803
Task 22-97-00-740-801 Task 24-41-00-861-801
Task 24-41-00-862-801
Task 25-53-00-000-801 Task 25-54-00-000-801
Task 25-53-00-400-801 Task 25-54-00-400-801
Task 27-44-51-400-801 Task 31-18-51-000-801
Task 31-18-51-400-801
Task 31-50-00-710-803 Task 31-60-00-710-802
Task 31-50-00-740-801
Task 33-14-00-710-801 Task 52-30-00-410-803
52-41-00, Page Block 001

AIRCRAFT WIRING MANUAL (AWM)

27-98-08

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)

20-33-00 20-33-42
20-33-44 20-43-12
20-51-20 20-52-10
20-52-21 20-54-50

REV 00 Oct 12/20 A330-27-3237

Page 28
 A330
SERVICE BULLETIN

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)

20-55-00 20-56-51

SERVICE BULLETIN (SB)

A330-27-3234

STRUCTURAL REPAIR MANUAL (SRM)

51-24-00 51-40-00
51-42-00 51-44-00
51-75-12

TECHNICAL FOLLOW UP (TFU)

27.44.00.022
STANDARDS MANUAL (SM)
CONF 005
(1) Modification
(a) Task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring for LSD

AIRCRAFT MAINTENANCE MANUAL (AMM)

06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-801
Task 12-34-24-860-802 Task 20-21-11-911-801
Task 20-28-00-912-810 Task 21-26-00-710-803
Task 22-97-00-740-801 Task 24-41-00-861-801
Task 24-41-00-862-801
Task 25-53-00-000-801 Task 25-54-00-000-801
Task 25-53-00-400-801 Task 25-54-00-400-801
Task 27-44-51-400-801 Task 31-18-51-000-801
Task 31-18-51-400-801
Task 31-50-00-710-803 Task 31-60-00-710-802
Task 31-50-00-740-801
Task 33-14-00-710-801 Task 52-30-00-410-803
52-41-00, Page Block 001

AIRCRAFT WIRING MANUAL (AWM)

27-98-08

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)

20-33-00 20-33-42
20-33-44 20-43-12
20-51-20 20-52-10
20-52-21 20-54-50
20-55-00 20-56-51

REV 00 Oct 12/20 A330-27-3237

Page 29
 A330
SERVICE BULLETIN

SERVICE BULLETIN (SB)

A330-27-3234

STRUCTURAL REPAIR MANUAL (SRM)

51-24-00 51-40-00
51-42-00 51-44-00
51-75-12

TECHNICAL FOLLOW UP (TFU)

27.44.00.022
STANDARDS MANUAL (SM)
CONF ALL
K. PUBLICATION AFFECTED
AIRCRAFT SCHEMATIC MANUAL (ASM)
AIRCRAFT WIRING LIST (AWL)
AIRCRAFT WIRING MANUAL (AWM)
ILLUSTRATED PARTS CATALOG (IPC)
L. INDUSTRY SUPPORT INFORMATION
AIRBUS will share the costs of accomplishment of this Service Bulletin by providing the kits
at no charge for orders placed before May 31/24.
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: [email protected].

REV 00 Oct 12/20 A330-27-3237

Page 30
 A330
SERVICE BULLETIN

2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
CONF 001
Material for task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring
for LSD

MATERIAL QTY SEE NOTES

Referenced tools See SB
Consumables See SB
Part kit 273237D01R02 1
Part kit 273237D05R02 1
Part kit 273237D09R02 1
Components See SB
Re-identified parts See SB
CONF 002
Material for task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring
for LSD

MATERIAL QTY SEE NOTES

Referenced tools See SB
Consumables See SB
Part kit 273237D02R02 1
Part kit 273237D04R01 1
Part kit 273237D05R02 1
Components See SB
Re-identified parts See SB
CONF 003
Material for task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring
for LSD

MATERIAL QTY SEE NOTES

Referenced tools See SB
Consumables See SB
Part kit 273237D02R02 1
Part kit 273237D05R02 1
Part kit 273237D08R00 1
Components See SB
Re-identified parts See SB
CONF 004
Material for task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring
for LSD

MATERIAL QTY SEE NOTES

Referenced tools See SB
Consumables See SB

REV 00 Oct 12/20 A330-27-3237

Page 31
 A330
SERVICE BULLETIN

MATERIAL QTY SEE NOTES

Part kit 273237D02R02 1
Part kit 273237D03R01 1
Part kit 273237D05R02 1
Components See SB
Re-identified parts See SB
CONF 005
Material for task set A330-A-27-XX-3237-01000-93AA-A Modification of the Wiring
for LSD

MATERIAL QTY SEE NOTES

Referenced tools See SB
Consumables See SB
Part kit 273237D01R02 1
Part kit 273237D06R04 1
Part kit 273237D07R03 1
Components See SB
Re-identified parts See SB
CONF ALL
B. TOOLING
CONF 001
Referenced tools for task set A330-A-27-XX-3237-01000-93AA-A Modification of
the Wiring for LSD
To accomplish this Service Bulletin it is necessary to use the tools listed in the subsequent
referenced tasks:
Ref. AMM Task 24-41-00-861-801
Ref. ESPM 20-52-21
CONF 002
Referenced tools for task set A330-A-27-XX-3237-01000-93AA-A Modification of
the Wiring for LSD
To accomplish this Service Bulletin it is necessary to use the tools listed in the subsequent
referenced tasks:
Ref. AMM Task 24-41-00-861-801
Ref. ESPM 20-52-21
CONF 003
Referenced tools for task set A330-A-27-XX-3237-01000-93AA-A Modification of
the Wiring for LSD
To accomplish this Service Bulletin it is necessary to use the tools listed in the subsequent
referenced tasks:
Ref. AMM Task 24-41-00-861-801
Ref. ESPM 20-52-21

REV 00 Oct 12/20 A330-27-3237

Page 32
 A330
SERVICE BULLETIN

CONF 004
Referenced tools for task set A330-A-27-XX-3237-01000-93AA-A Modification of
the Wiring for LSD
To accomplish this Service Bulletin it is necessary to use the tools listed in the subsequent
referenced tasks:
Ref. AMM Task 24-41-00-861-801
Ref. ESPM 20-52-21
CONF 005
Referenced tools for task set A330-A-27-XX-3237-01000-93AA-A Modification of
the Wiring for LSD
To accomplish this Service Bulletin it is necessary to use the tools listed in the subsequent
referenced tasks:
Ref. AMM Task 24-41-00-861-801
Ref. ESPM 20-52-21
CONF ALL
C. CONSUMABLES
CONF 001
Consumables for task set A330-A-27-XX-3237-01000-93AA-A Modification of the
Wiring for LSD

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

04CMA2 Wash Primer - - - Structure
Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure
Polysulfide Sealant -
06AAC1
General Purpose Interfay
Non Aqueous Cleaner -
08BAA9
General
Wire - Locking Dia: 0.6 mm
14QEB1
CRES Nickel Alloy
14SBA1 Textile - Lint free Cotton
CONF 002
Consumables for task set A330-A-27-XX-3237-01000-93AA-A Modification of the
Wiring for LSD

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure
Non Aqueous Cleaner -
08BAA9
General

REV 00 Oct 12/20 A330-27-3237

Page 33
 A330
SERVICE BULLETIN

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

Wire - Locking Dia: 0.6 mm
14QEB1
CRES Nickel Alloy
14SBA1 Textile - Lint free Cotton
CONF 003
Consumables for task set A330-A-27-XX-3237-01000-93AA-A Modification of the
Wiring for LSD

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure
Non Aqueous Cleaner -
08BAA9
General
Wire - Locking Dia: 0.6 mm
14QEB1
CRES Nickel Alloy
14SBA1 Textile - Lint free Cotton
CONF 004
Consumables for task set A330-A-27-XX-3237-01000-93AA-A Modification of the
Wiring for LSD

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure
Non Aqueous Cleaner -
08BAA9
General
Wire - Locking Dia: 0.6 mm
14QEB1
CRES Nickel Alloy
14SBA1 Textile - Lint free Cotton
CONF 005
Consumables for task set A330-A-27-XX-3237-01000-93AA-A Modification of the
Wiring for LSD

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

04CMA2 Wash Primer - - - Structure
Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure
Polysulfide Sealant -
06AAC1
General Purpose Interfay

REV 00 Oct 12/20 A330-27-3237

Page 34
 A330
SERVICE BULLETIN

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

Non Aqueous Cleaner -
08BAA9
General
Wire - Locking Dia: 0.6 mm
14QEB1
CRES Nickel Alloy
14SBA1 Textile - Lint free Cotton
CONF ALL
D. LIST OF NEW PARTS
CONF 001 005
Part kit 273237D01R02

Cost 8500.00 USD

Availability 240 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
[email protected].
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.

AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
Procurement address D4296
GERMANY
Phone: +49 40 743 51616
E-mail: [email protected]
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

29 NSA935401-00 1 TIE
30 MS21047L3 2 NUT
57 F5398895426000 1 BRACKET
58 F5398895426200 1 BRACKET
59 D5357068121400 1 ANGLE
60 EN6081D5-07 8 RIVET
108 EN6081D5-06 4 RIVET
109 F5398895403200 1 BRACKET
110 EN6101AD3-03 4 RIVET
111 NAS1149C0363R 1 WASHER
113 D9249171620200 2 BRACKET
114 EN6081AD4-08 6 RIVET

REV 00 Oct 12/20 A330-27-3237

Page 35
 A330
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

115 MS21043-3 2 NUT
116 NSA5067-08-1 2 NUT
117 F5398895426400 1 BRACKET
118 NAS1149D0332K 4 WASHER
119 NAS6703-3 2 BOLT
120 NAS1149CN432R 10 WASHER
121 NAS1101-04-6 1 SCREW
122 NAS1101-04-7 9 SCREW
123 MS21042-04 10 NUT
124 EN2997KE510 1 CONNECTR
125 EN2997KE508 1 CONNECTR
126 F9297582000000 1 HARNESS
127 F9249016920000 1 PLATE
128 F9249016920200 1 PLATE
130 EN2997KE3C10 1 CAP
F9297001400400 1 ELECEQPT
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 002-004
Part kit 273237D02R02

Cost 15000.00 USD

Availability 240 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
[email protected].
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.

AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
Procurement address D4296
GERMANY
Phone: +49 40 743 51616
E-mail: [email protected]
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

REV 00 Oct 12/20 A330-27-3237

Page 36
 A330
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

1 ABS0805-13 6 CLAMP
2 ABS0805-15 3 CLAMP
5 NAS1801-3-21 10 SCREW
6 NAS1096-3-8 4 SCREW
7 NAS1149C0332R 21 WASHER
8 NSA5527-03-03D 4 SPACER
9 NSA5527-03-08 2 SPACER
10 NAS1291C3M 16 NUT
11 NSA5066-3-1 3 NUT
12 NSA5067-3-1 1 NUT
14 AS21919WCH09 2 CLAMP
16 ABS0805-08 2 CLAMP
18 ABS0805-12 1 CLAMP
19 NSA5527-03-08D 10 SPACER
21 NAS1801-3-9 7 SCREW
22 NSA935808C01 20 WASHER
24 AS21919WCH10 4 CLAMP
25 ABS0805-09 9 CLAMP
26 ABS0805-10 7 CLAMP
27 AS21919WCH08 2 CLAMP
29 NSA935401-00 1 TIE
43 ABS0805-07 3 CLAMP
44 NAS1801-3-28 2 SCREW
45 NSA5527-03-02D 2 SPACER
46 NAS1801-3-19 3 SCREW
57 F5398895426000 1 BRACKET
58 F5398895426200 1 BRACKET
59 D5357068121400 1 ANGLE
60 EN6081D5-07 8 RIVET
66 AS21919WCH12 2 CLAMP
68 NAS1801-3-10 2 SCREW
70 NAS1801-3-12 2 SCREW
73 NSA936603CC0100 1 CAP
120 NAS1149CN432R 10 WASHER
121 NAS1101-04-6 1 SCREW
122 NAS1101-04-7 9 SCREW
123 MS21042-04 10 NUT
124 EN2997KE510 1 CONNECTR
125 EN2997KE508 1 CONNECTR
126 F9297582000000 1 HARNESS
127 F9249016920000 1 PLATE

REV 00 Oct 12/20 A330-27-3237

Page 37
 A330
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

128 F9249016920200 1 PLATE
130 EN2997KE3C10 1 CAP
F9297001300700 1 ELECEQPT
F9297001400400 1 ELECEQPT
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 004
Part kit 273237D03R01

Cost 770.00 USD

Availability 240 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
[email protected].
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.

AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
Procurement address D4296
GERMANY
Phone: +49 40 743 51616
E-mail: [email protected]
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

30 MS21047L3 1 NUT
47 F5397083300000 2 SECTION
48 D9249171620000 1 BRACKET
49 EN6081AD4-06 7 RIVET
50 F5398895427400 1 BRACKET
52 EN6081AD4-07 3 RIVET
53 DAN7-6-7X 2 PIN
54 DAN12-6X 2 COLLAR

REV 00 Oct 12/20 A330-27-3237

Page 38
 A330
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

55 EN6101AD3-04 2 RIVET
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 002
Part kit 273237D04R01

Cost 600.00 USD

Availability 240 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
[email protected].
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.

AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
Procurement address D4296
GERMANY
Phone: +49 40 743 51616
E-mail: [email protected]
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

30 MS21047L3 1 NUT
47 F5397083300000 1 SECTION
48 D9249171620000 1 BRACKET
49 EN6081AD4-06 5 RIVET
52 EN6081AD4-07 4 RIVET
55 EN6101AD3-04 2 RIVET
141 F5398895427600 1 BRACKET
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.

REV 00 Oct 12/20 A330-27-3237

Page 39
 A330
SERVICE BULLETIN

CONF 001-004
Part kit 273237D05R02

Cost 380.00 USD

Availability 180 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
[email protected].
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.

AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
Procurement address D4296
GERMANY
Phone: +49 40 743 51616
E-mail: [email protected]
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

32 NAS1100-06-10 4 SCREW
56 NAS1149CN616R 4 WASHER
62 ABS0772A01A 1 CLIP
99 NSA931320-030 1 CB
134 NSA939526-03C 1 SHUNT
136 G9297006500400 1 EQUIPMNT
177 EN3155-018M1616 1 PIN
E0397FY2000 1 CONTACT
F9237000703600 1 PLCRDSET
F9237000704000 1 PLCRDSET
F9237000704200 1 PLCRDSET
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 005
Part kit 273237D06R04

Cost 370.00 USD

Availability 180 d (calendar days from receipt of order)
NOTE(S)

REV 00 Oct 12/20 A330-27-3237

Page 40
 A330
SERVICE BULLETIN

The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
[email protected].
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.

AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
Procurement address D4296
GERMANY
Phone: +49 40 743 51616
E-mail: [email protected]
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

32 NAS1100-06-10 4 SCREW
56 NAS1149CN616R 4 WASHER
62 ABS0772A01A 1 CLIP
99 NSA931320-030 1 CB
134 NSA939526-03C 1 SHUNT
136 G9297006500600 1 EQUIPMNT
177 EN3155-018M1616 1 PIN
E0397FY2000 1 CONTACT
F9237000703600 1 PLCRDSET
F9237000704000 1 PLCRDSET
F9237000704200 1 PLCRDSET
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
Part kit 273237D07R03

Cost 10500.00 USD

Availability 240 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
[email protected].
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.

REV 00 Oct 12/20 A330-27-3237

Page 41
 A330
SERVICE BULLETIN

AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
Procurement address D4296
GERMANY
Phone: +49 40 743 51616
E-mail: [email protected]
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

1 ABS0805-13 2 CLAMP
2 ABS0805-15 2 CLAMP
5 NAS1801-3-21 21 SCREW
7 NAS1149C0332R 28 WASHER
9 NSA5527-03-08 6 SPACER
10 NAS1291C3M 18 NUT
11 NSA5066-3-1 5 NUT
12 NSA5067-3-1 2 NUT
14 AS21919WCH09 2 CLAMP
15 AS21919WCH13 5 CLAMP
18 ABS0805-12 4 CLAMP
19 NSA5527-03-08D 17 SPACER
20 NAS1801-08-21 2 SCREW
21 NAS1801-3-9 12 SCREW
22 NSA935808C01 17 WASHER
23 NAS1149CN832R 2 WASHER
24 AS21919WCH10 2 CLAMP
25 ABS0805-09 6 CLAMP
26 ABS0805-10 5 CLAMP
27 AS21919WCH08 5 CLAMP
29 NSA935401-00 1 TIE
66 AS21919WCH12 2 CLAMP
67 ABS0805-11 2 CLAMP
73 NSA936603CC0100 1 CAP
F9297001300800 1 ELECEQPT
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.

REV 00 Oct 12/20 A330-27-3237

Page 42
 A330
SERVICE BULLETIN

CONF 003
Part kit 273237D08R00

Cost 600.00 USD

Availability 240 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
[email protected].
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.

AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
Procurement address D4296
GERMANY
Phone: +49 40 743 51616
E-mail: [email protected]
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

30 MS21047L3 1 NUT
47 F5397083300000 1 SECTION
48 D9249171620000 1 BRACKET
49 EN6081AD4-06 5 RIVET
50 F5398895427400 1 BRACKET
52 EN6081AD4-07 3 RIVET
53 DAN7-6-7X 2 PIN
54 DAN12-6X 2 COLLAR
55 EN6101AD3-04 2 RIVET
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 001
Part kit 273237D09R02

Cost 10500.00 USD

Availability 240 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be

REV 00 Oct 12/20 A330-27-3237

Page 43
 A330
SERVICE BULLETIN

obtained through the AIRBUS Spares portal or through a request for quotation to
[email protected].
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.

AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
Procurement address D4296
GERMANY
Phone: +49 40 743 51616
E-mail: [email protected]
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

1 ABS0805-13 2 CLAMP
2 ABS0805-15 2 CLAMP
5 NAS1801-3-21 21 SCREW
7 NAS1149C0332R 28 WASHER
9 NSA5527-03-08 6 SPACER
10 NAS1291C3M 18 NUT
11 NSA5066-3-1 5 NUT
12 NSA5067-3-1 2 NUT
14 AS21919WCH09 2 CLAMP
15 AS21919WCH13 5 CLAMP
18 ABS0805-12 4 CLAMP
19 NSA5527-03-08D 17 SPACER
20 NAS1801-08-21 2 SCREW
21 NAS1801-3-9 12 SCREW
22 NSA935808C01 17 WASHER
23 NAS1149CN832R 2 WASHER
24 AS21919WCH10 2 CLAMP
25 ABS0805-09 6 CLAMP
26 ABS0805-10 5 CLAMP
27 AS21919WCH08 5 CLAMP
29 NSA935401-00 1 TIE
66 AS21919WCH12 2 CLAMP
67 ABS0805-11 2 CLAMP
73 NSA936603CC0100 1 CAP

REV 00 Oct 12/20 A330-27-3237

Page 44
 A330
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

F9297001300600 1 ELECEQPT
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
Components for task set A330-A-27-XX-3237-01000-93AA-A Modification of the
Wiring for LSD

AIRBUS Material, Logistics and Suppliers

Customer Order Fulfilment
Weg beim Jaeger 150
D-22335 HAMBURG
Procurement address D4296 GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

F9100095127395
1 PLCRDSET (1) (2)
(D4296)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
CONF 002
Components for task set A330-A-27-XX-3237-01000-93AA-A Modification of the
Wiring for LSD

AIRBUS Material, Logistics and Suppliers

Customer Order Fulfilment
Weg beim Jaeger 150
D-22335 HAMBURG
Procurement address D4296 GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

REV 00 Oct 12/20 A330-27-3237

Page 45
 A330
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

F9100095127395
1 PLCRDSET (1) (2)
(D4296)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
CONF 003
Components for task set A330-A-27-XX-3237-01000-93AA-A Modification of the
Wiring for LSD

AIRBUS Material, Logistics and Suppliers

Customer Order Fulfilment
Weg beim Jaeger 150
D-22335 HAMBURG
Procurement address D4296 GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

F9100095127395
1 PLCRDSET (1) (2)
(D4296)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
CONF 004
Components for task set A330-A-27-XX-3237-01000-93AA-A Modification of the
Wiring for LSD

AIRBUS Material, Logistics and Suppliers

Customer Order Fulfilment
Weg beim Jaeger 150
D-22335 HAMBURG
Procurement address D4296 GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

REV 00 Oct 12/20 A330-27-3237

Page 46
 A330
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

F9100095127395
1 PLCRDSET (1) (2)
(D4296)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
CONF 005
Components for task set A330-A-27-XX-3237-01000-93AA-A Modification of the
Wiring for LSD

AIRBUS Material, Logistics and Suppliers

Customer Order Fulfilment
Weg beim Jaeger 150
D-22335 HAMBURG
Procurement address D4296 GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

F9100095127395
1 PLCRDSET (1) (2)
(D4296)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
CONF ALL
E. LIST OF EXISTING PARTS
CONF 001
Re-identified parts for task set A330-A-27-XX-3237-01000-93AA-A Modification of
the Wiring for LSD

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
33 F9259001300800 PANEL (33) F9259001300600
33 F9259001301000 PANEL (33) F9259001300400
CONF 002
Re-identified parts for task set A330-A-27-XX-3237-01000-93AA-A Modification of
the Wiring for LSD

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
33 F9259001300800 PANEL (33) F9259001300600

REV 00 Oct 12/20 A330-27-3237

Page 47
 A330
SERVICE BULLETIN

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
33 F9259001301000 PANEL (33) F9259001300400
CONF 003
Re-identified parts for task set A330-A-27-XX-3237-01000-93AA-A Modification of
the Wiring for LSD

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
33 F9259001300800 PANEL (33) F9259001300600
33 F9259001301000 PANEL (33) F9259001300400
CONF 004
Re-identified parts for task set A330-A-27-XX-3237-01000-93AA-A Modification of
the Wiring for LSD

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
33 F9259001300800 PANEL (33) F9259001300600
33 F9259001301000 PANEL (33) F9259001300400
CONF 005
Re-identified parts for task set A330-A-27-XX-3237-01000-93AA-A Modification of
the Wiring for LSD

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
33 F9259001300800 PANEL (33) F9259001300600

REV 00 Oct 12/20 A330-27-3237

Page 48
 A330
SERVICE BULLETIN

CONF ALL
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A330-A-27-XX-3237-01000-93AA-A (A330-A-27-XX-3237-01ZZZ-93AZ-A)
Modification of the Wiring for LSD

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.

WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING NOTICES ARE IN
POSITION BEFORE YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND RELATED DOORS
- OTHER COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS
AND/OR DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
CLEAR.
MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE.

CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL

WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.

NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.

NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.

NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.

REV 00 Oct 12/20 A330-27-3237

Page 49
 A330
SERVICE BULLETIN

NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by

an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
To allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.

NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.

NOTE: Discarded parts must be managed at the operator's discretion.

A. TASK SET ASSOCIATED INFORMATION

Task Manpower
CONF 001
TOTAL MAN-HOURS 54.00 h
CONF 002
TOTAL MAN-HOURS 54.00 h
CONF 003
TOTAL MAN-HOURS 54.00 h
CONF 004
TOTAL MAN-HOURS 54.00 h
CONF 005
TOTAL MAN-HOURS 54.00 h
CONF 001
ELAPSED TIME (HOURS) 54.00 h
CONF 002
ELAPSED TIME (HOURS) 54.00 h
CONF 003
ELAPSED TIME (HOURS) 54.00 h
CONF 004
ELAPSED TIME (HOURS) 54.00 h
CONF 005
ELAPSED TIME (HOURS) 54.00 h
CONF ALL
B. PREPARATION
(1) Task A330-A-27-XX-3237-01001-920A-A (A330-A-27-XX-3237-01ZZZ-920Z-A)
Job Set-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h

Referenced Information

Manuals/Drawings References/Sheets
Task 12-34-24-860-802
AMM
Task 25-53-00-000-801

REV 00 Oct 12/20 A330-27-3237

Page 50
 A330
SERVICE BULLETIN

Manuals/Drawings References/Sheets
Task 25-54-00-000-801
52-41-00, Page Block 001
Procedure

NOTE: For the basic Aircraft configuration, refer to AMM Chapter "Introduction -
Aircraft status for maintenance" in Manual Front Matter section.

(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM Task 12-34-
24-860-802.
(b) Remove the AFT cargo ceiling panels (Panel 151FC, Panel 151HC, Panel 151KC
and Panel 151PC) from the AFT cargo compartment, refer to Ref. AMM Task 25-
53-00-000-801.
(c) Remove the ceiling panels (Panel 161DC, Panel 161EC and Panel 161FC) from
the bulk cargo compartment, refer to Ref. AMM Task 25-54-00-000-801.
(d) Remove the sidewall panels (Panel 162RW and Panel 162KW) from the bulk
cargo compartment, refer to Ref. AMM Task 25-54-00-000-801.
(e) Open the maintenance door 312AR, refer to Ref. AMM 52-41-00, Page Block 001.
(2) Task A330-A-27-XX-3237-06001-920A-A (A330-A-27-XX-3237-06ZZZ-920Z-A)
Aircraft System Configuration
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h

Procedure
(a) In the cockpit, on the ELEC control Panel 235VU, make sure that these
pushbutton switches are released:
- BAT1, BAT2, APU BAT
- GEN1, 2, APU GEN
- EXT A (B).
(b) Open, safety/lock and tag this (these) circuit breaker(s):

PANEL DESIGNATION FIN LOCATION SEE NOTES

701PP 10PB1 (1) (2)
702PP 10PB2 (1) (3)
NOTE(S)
(1): For circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-801.
(2): The circuit breaker FIN 10PB1 is located on panel 742VU at position 72S.
(3): The circuit breaker FIN 10PB2 is located on panel 742VU at position 71S.
(c) Put the warning notices in position in the cockpit to tell persons not to operate
the pushbutton switches on the overhead panels:
- 211VU (EMER ELEC PWR)
- 235VU (ELEC).

REV 00 Oct 12/20 A330-27-3237

Page 51
 A330
SERVICE BULLETIN

(d) Put the warning notices in position in the cockpit to tell persons not to start the
Auxiliary Power Unit (APU).
(e) Make sure that the external connector(s) is (are) not connected to the aircraft
receptacle(s) EXT PWR A (B).
(f) Put the warning notices in position at the Door 121EL to tell persons not to
connect the external power connector(s).
C. PROCEDURE
CONF 001 005
(1) Task A330-A-27-XX-3237-01001-510A-A (A330-A-27-XX-3237-01ZZZ-510Z-A)
Cut the Wire 2499-5020 in the Electrical Harness 5871VB
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 85 to Frame 86
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) At the FR86, cut the wire 2499–5020 close to the beginning of the lightning
protection hose, refer to Ref. Fig. Cut the Wire 2499-5020 in Electrical Harness
5871VB, view C.
Refer to Ref. Fig. Hook-up Chart of the Modification of the Wiring in Electrical
Harness 5871VB.

REV 00 Oct 12/20 A330-27-3237

Page 52
 A330
SERVICE BULLETIN

CONF 001 005

Z310

FR91

FR87

FR86

FR85

FR84
FR83
FR80 /82
5871VB /1M

ICN-A330-A-27XX3237-A-FAPE3-012CX-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012CX-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Cut the Wire 2499-5020 in Electrical Harness 5871VB
Page 53
 A330
SERVICE BULLETIN

CONF 001 005

TO
5123VC

FR87

FR86

5871VB /1M

FR85

C
TO
5205VP

ICN-A330-A-27XX3237-A-FAPE3-012CY-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012CY-A-001-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Cut the Wire 2499-5020 in Electrical Harness 5871VB
Page 54
 A330
SERVICE BULLETIN

CONF 001 005

FR85

FR86

5213VT

TO
5205VP

TO
5123VC

LIGHTNING
PROTECTION HOSE

CUT POSITION 5871VB /1M

OF THE WIRE
2499-5020
C

ICN-A330-A-27XX3237-A-FAPE3-012CZ-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012CZ-A-002-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Cut the Wire 2499-5020 in Electrical Harness 5871VB
Page 55
 A330
SERVICE BULLETIN

CONF 001 005

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 26100 1027,6 311 5123VC G EN3155-019F2018 BEFORE

2 311 - - NSA936603CC0100 2499-5020 - 1M DR20 5000 196,9 311 5123VC G EN3155-019F2018 AFTER

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70012 002 00 "SHEET 06,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-014EJ-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5871VB
Page 56
 A330
SERVICE BULLETIN

CONF 002-004
(1) Task A330-A-27-XX-3237-01002-510A-A (A330-A-27-XX-3237-01ZZZ-510Z-A)
Cut the Wire 2499-5020 in the Electrical Harness 5871VB
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 85 to Frame 86
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) At the FR86, cut the wire 2499–5020 close to the beginning of the lightning
protection hose, refer to Ref. Fig. Cut the Wire 2499-5020 in Electrical Harness
5871VB, view C.
Refer to Ref. Fig. Hook-up Chart of the Modification of the Wiring in Electrical
Harness 5871VB.

REV 00 Oct 12/20 A330-27-3237

Page 57
 A330
SERVICE BULLETIN

CONF 002-004

Z310

FR91

FR87

FR86

FR85

FR84
5871VB /1M
FR83
FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-012D2-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012D2-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Cut the Wire 2499-5020 in Electrical Harness 5871VB
Page 58
 A330
SERVICE BULLETIN

CONF 002-004

TO
5123VC

FR87

5871VB /1M

FR86 TO
5205VP

FR85

ICN-A330-A-27XX3237-A-FAPE3-012D3-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012D3-A-001-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Cut the Wire 2499-5020 in Electrical Harness 5871VB
Page 59
 A330
SERVICE BULLETIN

CONF 002-004

FR85

5213VT

FR86
TO
5205VP

TO
5123VC

LIGHTNING
PROTECTION HOSE
CUT POSITION 5871VB /1M
OF THE WIRE
2499-5020

ICN-A330-A-27XX3237-A-FAPE3-012D4-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012D4-A-002-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Cut the Wire 2499-5020 in Electrical Harness 5871VB
Page 60
 A330
SERVICE BULLETIN

CONF 002-004

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 26100 1027,6 311 5123VC G EN3155-019F2018 BEFORE

2 311 - - NSA936603CC0100 2499-5020 - 1M DR20 5000 196,9 311 5123VC G EN3155-019F2018 AFTER

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70012 002 00 "SHEET 06,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-014EJ-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5871VB
Page 61
 A330
SERVICE BULLETIN

CONF 001
(2) Task A330-A-27-XX-3237-01001-520A-A (A330-A-27-XX-3237-01ZZZ-520Z-A)
Remove the Electrical Harness 5869VB from the Structure between FR86 and
FR87 Traverse (with Loop-Clamps)
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 86 to Frame 87
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM
06-41-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
SRM 51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
5 Tag all the parts you must remove and retain to make the subsequent
installation easier.
6 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
(b) Remove the harness 5869VB from the structure between Frame 86 and Frame 87
Refer to Ref. Fig. Remove the Electrical Harness 5869VB from the Structure
between FR86 and FR87
1 Remove, as shown on view D:

4 CLAMP Item (1) Discard

1 CLAMP Item (14) Discard

2 CLAMP Item (15) Discard

2 CLAMP Item (16) Discard

REV 00 Oct 12/20 A330-27-3237

Page 62
 A330
SERVICE BULLETIN

2 SCREW HEXAGON-HEAD Item (3) Discard

2 SCREW HEXAGON-HEAD Item (4) Discard

3 SCREW HEXAGON-HEAD Item (6) Discard

7 WASHER Item (7) Discard

4 SPACER Item (8) Discard

2 NUT Item (10) Discard

1 NUT-CLIP, SELF LOCKIN Item (11) Discard

2 NUT-CLIP Item (12) Discard

1 NUT SELF LOCKIN Item (13) Discard

2 At the grounding point 5287VN, as shown on view D, disconnect:

2 BONDING CABLE
attached with:

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT Item (10) Discard

3 Remove, as shown on view E:

2 CLAMP Item (14) Discard

3 CLAMP Item (16) Discard

4 SCREW HEXAGON-HEAD Item (3) Discard

4 WASHER Item (7) Discard

2 SPACER Item (8) Discard

2 SPACER Item (9) Discard

1 NUT Item (10) Discard

4 Remove, as shown on view F:

2 CLAMP Item (15) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT Item (10) Discard

5 Remove, as shown on view G:

1 CLAMP Item (15) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT-CLIP, SELF LOCKIN Item (11) Discard

REV 00 Oct 12/20 A330-27-3237

Page 63
 A330
SERVICE BULLETIN

6 Remove, as shown on view J:

1 CLAMP Item (14) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT-CLIP, SELF LOCKIN Item (11) Discard

7 At FR86, remove, as shown on view H:

1 CLAMP Item (18) Discard

1 BONDING-STRIP Item (17) Discard

attached with:

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 SPACER Item (8) Discard

1 NUT Item (10) Discard

REV 00 Oct 12/20 A330-27-3237

Page 64
 A330
SERVICE BULLETIN

CONF 001

Z310

FR91

FR87

FR86

FR85

FR84
FR83
5869VB /1MF FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-012XC-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012XC-A-001-01 SHEET 1/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 65
 A330
SERVICE BULLETIN

CONF 001
TO
5219VC
5202VC
5203VC

FR87

1CSB

TO
1CSJ
D

1CSG
5287VN /DC1
C
FR86
5869VB /1MF
F
H

FR85

TO
5205VP

ICN-A330-A-27XX3237-A-FAPE3-012XD-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012XD-A-002-01 SHEET 2/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 66
 A330
SERVICE BULLETIN

CONF 001

FR87

5287VN /DC1

5869VB /1MF
J

1CSJ

TO
1CSG

ICN-A330-A-27XX3237-A-FAPE3-012XE-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012XE-A-002-01 SHEET 3/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 67
 A330
SERVICE BULLETIN

CONF 001
TO
5219VC FR87
5202VC
(4) (1) 5203VC
(7)

5869VB /1MF
(1)

(4)
(1) (8)
(7)
(10) (10)
(8)
(1)

(14)

(6)
(7)

(6) (11)
(7)

(15)
TO
(3) (16) 1CSJ

(12)
(7)
TO
(8) (16) 1CSB
(12) 1CSG
(3)
(13)
(7) (15)
(6)
(6) (7) (7)
TO (8)
5205VP

(10)
5287VN /DC1
D

ICN-A330-A-27XX3237-A-FAPE3-012XF-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012XF-A-002-01 SHEET 4/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 68
 A330
SERVICE BULLETIN

CONF 001
(3)
(7)

5869VB /1MF

(3)
(7) (14)

(16)

(3) (9)
(16)
(7)

5870VB /2MF
(16)
(8)

(14) (8)

FR87
(10)
E
(9)

(10)

(15)
5869VB /1MF

(15) 5871VB /1M

(7)

(6)
F

ICN-A330-A-27XX3237-A-FAPE3-012XG-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012XG-A-001-01 SHEET 5/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 69
 A330
SERVICE BULLETIN

CONF 001
(11)
FR87

(6)
(7)
(14) (6)
(7)
(15)

(11)

G J

FR86

(8)

(10)
(6)
(7)

5869VB /1MF

(17)

5871VB /1M (18)

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-012XH-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-012XH-A-001-01 SHEET 6/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 70
 A330
SERVICE BULLETIN

CONF 002-004
(2) Task A330-A-27-XX-3237-01002-520A-A (A330-A-27-XX-3237-01ZZZ-520Z-A)
Remove the Electrical Harness 5869VB from the Structure between FR86 and
FR87 V-Prop (with P-Clamps)
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 86 to Frame 87
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
SRM 51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
5 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810
(b) Remove the electrical harness 5869VB between Frame 86 and Frame 87
Refer to Ref. Fig. Remove the Electrical Harness 5869VB from the Structure
between FR86 and FR87
1 Remove, as shown on view C:

3 CLAMP Item (37) Discard

5 CLAMP Item (27) Discard

5 SCREW HEXAGON-HEAD Item (4) Discard

5 WASHER Item (7) Discard

5 SPACER Item (35) Discard

5 NUT-CLIP, SELF LOCKIN Item (11) Discard

REV 00 Oct 12/20 A330-27-3237

Page 71
 A330
SERVICE BULLETIN

2 Remove, as shown on view D:

2 CLAMP Item (14) Discard

2 CLAMP Item (38) Discard

2 SCREW HEXAGON-HEAD Item (4) Discard

2 WASHER Item (7) Discard

2 SPACER Item (35) Discard

2 NUT Item (10) Discard

3 At the grounding point 5287VN, as shown on view D, disconnect:

1 BONDING CABLE
attached with:

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT Item (10) Discard

4 Remove, as shown on view E:

1 CLAMP Item (14) Discard

1 CLAMP Item (37) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT-CLIP Item (12) Discard

5 Remove, as shown on view F:

1 CLAMP Item (38) Discard

1 SCREW HEXAGON-HEAD Item (42) Discard

1 WASHER Item (41) Discard

1 SPACER Item (35) Discard

6 At FR86, remove, as shown on view G:

2 CLAMP Item (15) Discard

2 BONDING STRIP Item (17) Discard

attached with:

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (22) Discard

7 Remove, as shown on view H:

4 CLAMP Item (15) Discard

2 SCREW HEXAGON-HEAD Item (6) Discard

2 WASHER Item (7) Discard

REV 00 Oct 12/20 A330-27-3237

Page 72
 A330
SERVICE BULLETIN

1 NUT Item (10) Discard

REV 00 Oct 12/20 A330-27-3237

Page 73
 A330
SERVICE BULLETIN

CONF 002-004

Z310

FR91

FR87

FR86

FR85

FR84
FR83
5869VB /1MF
FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-0136A-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136A-A-001-01 SHEET 1/5

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 74
 A330
SERVICE BULLETIN

CONF 002-004

TO
5219VC
5202VC
5203VC

C
TO
G 1CSJ
1CSB
FR87
H

F
1CSG
E

5287VN /DC1 5869VB /1MF

FR86 TO
5205VP
D

FR85

ICN-A330-A-27XX3237-A-FAPE3-0136B-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136B-A-001-01 SHEET 2/5

REV 00 Oct 12/20 A330-27-3237
Remove the Electrical Harness 5869VB from the Structure between FR86 and FR87
Page 75
 A330
SERVICE BULLETIN

CONF 002-004

(11)

(11)

(11)

(35) (35)
(11)
(37)
5869VB /1MF

(11)
FR87
(35) (27)
(27)

(35) (7)
(4)
(27)
(37)

(35) (7)
(27) (4)
5870VB /2MF
(37)

(27) 5867VB /1SF

(7)
(4)

(7)
(4)

ICN-A330-A-27XX3237-A-FAPE3-0136C-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136C-A-002-01 SHEET 3/5

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 76
 A330
SERVICE BULLETIN

CONF 002-004

5871VB /1M
(10)
FR87
(14)

(35)

(38) (14)

(7)
(4)
(35)

5287VN /DC1

(38)
(10) 5869VB /1MF
(7)
(6)
D

5869VB /1MF 5871VB /1M

(6) (14)
(7)

(37)

E
(12)

ICN-A330-A-27XX3237-A-FAPE3-0136D-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136D-A-001-01 SHEET 4/5

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 77
 A330
SERVICE BULLETIN

CONF 002-004

5869VB /1MF (38) (42)

FR86
(41)

(35)

(15)

F
(17)
5869VB /1MF

(17)

5871VB /1M
(15)
(10) (22)

(6)

G
(15)

(15)
5869VB /1MF

5871VB /1M

(15) (15)

(7)
H
(6)

ICN-A330-A-27XX3237-A-FAPE3-0136E-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136E-A-002-01 SHEET 5/5

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 78
 A330
SERVICE BULLETIN

CONF 005
(2) Task A330-A-27-XX-3237-01003-520A-A (A330-A-27-XX-3237-01ZZZ-520Z-A)
Remove the Electrical Harness 5869VB from the Structure between FR86 and
FR87 Traverse (with P-Clamps)
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 86 to Frame 87
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
SRM 51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
4 Tag all the parts you must remove and retain to make the subsequent
installation easier.
5 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
(b) Remove the electrical harness 5869VB between Frame 86 and Frame 87, refer to
Ref. Fig. Remove the Electrical Harness 5869VB from the Structure between FR86
and FR87.
1 Remove, as shown on view D:

4 CLAMP Item (2) Discard

1 CLAMP Item (14) Discard

2 CLAMP Item (15) Discard

2 CLAMP Item (16) Discard

2 SCREW HEXAGON-HEAD Item (3) Discard

2 SCREW HEXAGON-HEAD Item (4) Discard

REV 00 Oct 12/20 A330-27-3237

Page 79
 A330
SERVICE BULLETIN

3 SCREW HEXAGON-HEAD Item (6) Discard

7 WASHER Item (7) Discard

4 SPACER Item (8) Discard

2 NUT Item (13) Discard

2 NUT-CLIP, SELF LOCKIN Item (11) Discard

2 NUT CLIP Item (12) Discard

2 At the grounding point 5287VN, as shown on view D, disconnect:

2 BONDING CABLE
attached with:

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT Item (10) Discard

3 Remove, as shown on view E:

3 CLAMP Item (16) Discard

2 CLAMP Item (14) Discard

4 SCREW HEXAGON-HEAD Item (3) Discard

4 WASHER Item (7) Discard

2 SPACER Item (8) Discard

2 SPACER Item (9) Discard

1 NUT Item (10) Discard

4 Remove, as shown on view F:

1 CLAMP Item (15) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT-CLIP, SELF LOCKIN Item (11) Discard

5 Remove, as shown on view G:

2 CLAMP Item (15) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT Item (10) Discard

6 At FR86, remove, as shown on view H:

1 CLAMP Item (15) Discard

1 BONDING STRIP Item (17) Discard

attached with:

REV 00 Oct 12/20 A330-27-3237

Page 80
 A330
SERVICE BULLETIN

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT Item (10) Discard

7 Remove, as shown on view J:

1 CLAMP Item (27) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT-CLIP, SELF LOCKIN Item (11) Discard

REV 00 Oct 12/20 A330-27-3237

Page 81
 A330
SERVICE BULLETIN

CONF 005

Z310

FR91

FR87

FR86

FR85

FR84
5869VB /1MF FR83
FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-01372-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01372-A-001-01 SHEET 1/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 82
 A330
SERVICE BULLETIN

CONF 005
TO
5219VC
5202VC
5203VC

E
D
FR87 C
1CSB

TO
1CSJ

1CSG
5287VN /DC1

FR86
5869VB /1MF
G
H

FR85

TO
5205VP

ICN-A330-A-27XX3237-A-FAPE3-01373-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01373-A-001-01 SHEET 2/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 83
 A330
SERVICE BULLETIN

CONF 005

FR87

5287VN /DC1

5869VB /1MF

1CSJ

TO
1CSG

ICN-A330-A-27XX3237-A-FAPE3-01374-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01374-A-002-01 SHEET 3/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 84
 A330
SERVICE BULLETIN

CONF 005
TO
5219VC FR87
5202VC
(4) (2) 5203VC
(7)

5869VB /1MF
(2)

(2)
(4)
(8)
(7)
(13)
(8) (11)
(2)

(14)

(6)
(7)

(6) (11)
(7)

(15)

(3) (16) TO
1CSJ

(12) (7) TO
(16) 1CSB
(8) 1CSG
(12)
(3)
(13)
(7) (15) (6)
(6) (7) (7)
TO
5205VP (8)

(10)
D 5287VN /DC1

ICN-A330-A-27XX3237-A-FAPE3-01375-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01375-A-001-01 SHEET 4/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 85
 A330
SERVICE BULLETIN

CONF 005
(3)
(7)

5869VB /1MF

(3)
(7) (14)

(16)

(3) (9)
(16)
(7)

5870VB /2MF
(16) (8)

(14) (8)

FR87 E
(10)

(9)

(6)
(7) FR87
(10)
(11)
TO
5219VC (15)
5202VC
5203VC 5869VB /1MF
(15)

5871VB /1M
(15)
(7)

(6)

F G

ICN-A330-A-27XX3237-A-FAPE3-01376-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01376-A-002-01 SHEET 5/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 86
 A330
SERVICE BULLETIN

CONF 005

FR86

(10)

(15)
(17)
5869VB /1MF

5871VB /1M
(6) (7)

(27) (6)
(7)

TO
1CSJ

(11)

ICN-A330-A-27XX3237-A-FAPE3-01377-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01377-A-001-01 SHEET 6/6

REV 00 Oct 12/20 Remove the Electrical Harness 5869VB A330-27-3237
from the Structure between FR86 and FR87 Page 87
 A330
SERVICE BULLETIN

CONF 001
(3) Task A330-A-27-XX-3237-02001-520A-A (A330-A-27-XX-3237-02ZZZ-520Z-A)
Remove the Electrical Harness 5870VB from the structure between FR86 and
FR87 Traverse (with Loop-Clamps)
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 86 to Frame 87
Manpower/Resources/Skills

Man-hours 2.50 h
Minimum Number of person 1
Elapsed Time 2.50 h
Skills Electrical

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
SRM 51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
4 Tag all the parts you must remove and retain to make the subsequent
installation easier.
5 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
(b) Remove the electrical harness 5870VB between Frame 86 and Frame 87, refer to
Ref. Fig. Remove the Electrical Harness 5870VB from the Structure between FR86
and FR87.
1 Remove, as shown on view D:

2 CLAMP Item (27) Discard

1 CLAMP Item (64) Discard

1 SCREW HEXAGON-HEAD Item (3) Discard

2 SCREW HEXAGON-HEAD Item (4) Discard

3 WASHER Item (7) Discard

2 SPACER Item (65) Discard

REV 00 Oct 12/20 A330-27-3237

Page 88
 A330
SERVICE BULLETIN

1 SPACER Item (8) Discard

1 NUT Item (13) Discard

2 Remove, as shown on view E:

1 CLAMP Item (18) Discard

1 CLAMP Item (16) Discard

1 CLAMP Item (27) Discard

3 SCREW HEXAGON-HEAD Item (3) Discard

2 SCREW HEXAGON-HEAD Item (6) Discard

5 WASHER Item (7) Discard

2 SPACER Item (8) Discard

1 SPACER Item (9) Discard

2 NUT Item (10) Discard

1 NUT Item (40) Discard

3 Remove, as shown on view F:

2 CLAMP Item (64) Discard

1 CLAMP Item (67) Discard

2 SCREW HEXAGON-HEAD Item (6) Discard

2 WASHER Item (7) Discard

2 SPACER Item (8) Discard

2 NUT Item (10) Discard

4 Remove, as shown on view G:

1 CLAMP Item (27) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT-CLIP, SELF LOCKIN Item (11) Discard

5 Remove, as shown on view H:

1 CLAMP Item (66) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 SPACER Item (9) Discard

1 NUT-CLIP, SELF LOCKIN Item (11) Discard

6 Remove, as shown on view J:

1 CLAMP Item (14) Discard

REV 00 Oct 12/20 A330-27-3237

Page 89
 A330
SERVICE BULLETIN

1 CLAMP Item (24) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT Item (10) Discard

7 At FR86, remove, as shown on view K:

1 CLAMP Item (67) Discard

1 BONDING STRIP Item (17) Discard

attached with:

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 SPACER Item (9) Discard

1 NUT Item (10) Discard

REV 00 Oct 12/20 A330-27-3237

Page 90
 A330
SERVICE BULLETIN

CONF 001

Z310

FR91

FR87

FR86

FR85

FR84
FR83
FR80 /82

5870VB /2MF

ICN-A330-A-27XX3237-A-FAPE3-0136I-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136I-A-001-01 SHEET 1/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 91
 A330
SERVICE BULLETIN

CONF 001

TO
5949VC H
5204VC
5205VC

J
F
5393VN /B2
FR87
C 5374VN /DC2
TO
1CSK 1CSD 5870VB /2MF

1CSH
D
FR86
TO
5200VP

FR85

ICN-A330-A-27XX3237-A-FAPE3-0136J-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136J-A-003-01 SHEET 2/6

REV 00 Oct 12/20 A330-27-3237
Remove the Electrical Harness 5870VB from the Structure between FR86 and FR87
Page 92
 A330
SERVICE BULLETIN

CONF 001

FR87

5870VB /2MF

1CSD
1CSK

5393VN /B2
5374VN /DC2

TO
1CSH

ICN-A330-A-27XX3237-A-FAPE3-0136K-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136K-A-002-01 SHEET 3/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 93
 A330
SERVICE BULLETIN

CONF 001

(3)
(7)
(64)

5870VB /2MF
(4)
(8)
(7)

(4) (27)

(7)
01
(27)

(65) (13)

(65)

FR87
D

FR87
5393VN /B2
(3) 5374VN /DC2

(7) 5870VB /2MF

(6)
(7)
(3)
(7)

(9)
(18)
5870VB /2MF (8) (27)
(7)
(8) (3)
(10)

(16)
E
(40)

NOTE:
01 DISCONNECTED WITH CABLE HARNESS 5869VB
ICN-A330-A-27XX3237-A-FAPE3-0136L-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136L-A-002-01 SHEET 4/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 94
 A330
SERVICE BULLETIN

CONF 001

(10)

FR87
(8)

(10)

(67)

(64)
(64)

5870VB /2MF

(7)
FR87

F (6)

5870VB /2MF

(6)
(7)

(27)

G
(11)

ICN-A330-A-27XX3237-A-FAPE3-0136M-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136M-A-001-01 SHEET 5/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 95
 A330
SERVICE BULLETIN

CONF 001
FR87
5870VB /2MF

(66)

(6)
(7)

(9)
(10)

(14)
(11)
5870VB /2MF

H
5872VB /2M
(24)

(7)
FR86

(6)

(9)
(10) J

(6)
(7)

(67)

5870VB /2MF

5872VB /2M
(17)

ICN-A330-A-27XX3237-A-FAPE3-0136N-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136N-A-001-01 SHEET 6/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 96
 A330
SERVICE BULLETIN

CONF 002-004
(3) Task A330-A-27-XX-3237-02002-520A-A (A330-A-27-XX-3237-02ZZZ-520Z-A)
Remove the Electrical Harness 5870VB from the structure between FR86 and
FR87 V-Prop (with P-Clamps)
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 86 to Frame 87
Manpower/Resources/Skills

Man-hours 2.50 h
Minimum Number of person 1
Elapsed Time 2.50 h
Skills Electrical

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
SRM 51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
4 Tag all the parts you must remove and retain to make the subsequent
installation easier.
5 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
(b) Remove the electrical harness 5870VB between Frame 86 and Frame 87, refer to
Ref. Fig. Remove the Electrical Harness 5870VB from the Structure between FR86
and FR87.
1 Remove, as shown on view C:

1 CLAMP Item (37) Discard

1 SCREW HEXAGON-HEAD Item (4) Discard

1 WASHER Item (7) Discard

1 SPACER Item (35) Discard

1 NUT-CLIP, SELF LOCKIN Item (11) Discard

REV 00 Oct 12/20 A330-27-3237

Page 97
 A330
SERVICE BULLETIN

2 Remove, as shown on view D:

1 CLAMP Item (27) Discard

1 SCREW HEXAGON-HEAD Item (68) Discard

1 WASHER Item (7) Discard

3 Remove, as shown on view E:

2 CLAMP Item (27) Discard

2 CLAMP Item (24) Discard

4 SCREW HEXAGON-HEAD Item (68) Discard

4 WASHER Item (7) Discard

4 NUT Item (10) Discard

4 Remove, as shown on view F:

4 CLAMP Item (27) Discard

2 SCREW HEXAGON-HEAD Item (68) Discard

2 WASHER Item (7) Discard

5 Remove, as shown on view G:

1 CLAMP Item (24) Discard

2 CLAMP Item (69) Discard

2 SCREW HEXAGON-HEAD Item (68) Discard

2 WASHER Item (7) Discard

1 NUT Item (10) Discard

6 At FR86, remove, as shown on view H:

1 CLAMP Item (24) Discard

1 CLAMP Item (69) Discard

2 BONDING STRIP Item (17) Discard

attached with:

1 SCREW HEXAGON-HEAD Item (68) Discard

1 WASHER Item (22) Discard

REV 00 Oct 12/20 A330-27-3237

Page 98
 A330
SERVICE BULLETIN

CONF 002-004

Z310

FR91

FR87

FR86
5870VB /2MF
FR85

FR84
FR83
FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-01378-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01378-A-001-01 SHEET 1/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 99
 A330
SERVICE BULLETIN

CONF 002-004
TO
5949VC
5204VC
5205VC

F
H

C
D
1CSD 5870VB /2MF
FR87 TO
TO 5200VP
1CSK

5393VN /B2
5374VN /DC2
E

1CSH

FR86

FR85

ICN-A330-A-27XX3237-A-FAPE3-01379-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01379-A-003-01 SHEET 2/6

REV 00 Oct 12/20 A330-27-3237
Remove the Electrical Harness 5870VB from the Structure between FR86 and FR87
Page 100
 A330
SERVICE BULLETIN

CONF 002-004
FR87
(11)

01

01
(35) 5870VB /2MF

(37)
01

01 01
01 (7)
(4)
5869VB /1MF 01
01 01
01

01
01

FR87 C

5870VB /2MF
(27)

(7)

(68)

NOTE:
01 DISCONNECTED WITH ELECTRICAL HARNESS 5869VB/1MF
ICN-A330-A-27XX3237-A-FAPE3-0137A-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137A-A-002-01 SHEET 3/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 101
 A330
SERVICE BULLETIN

CONF 002-004

FR87
(10)

(24) 5872VB /2M

(68) (27)
(7)

(7)
(68)

5374VN /DC2

5393VN /B2 (27)

(10)
(24)

5870VB /2MF

ICN-A330-A-27XX3237-A-FAPE3-0137B-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137B-A-002-01 SHEET 4/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 102
 A330
SERVICE BULLETIN

CONF 002-004

(27)
FR87
5872VB /2M
5870VB /2MF

(27)
(7) (68)

(68) (7)
(27)

(27)

ICN-A330-A-27XX3237-A-FAPE3-0137C-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137C-A-002-01 SHEET 5/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 103
 A330
SERVICE BULLETIN

CONF 002-004
(10)

(69)
5872VB /2M (24)

FR86

5870VB /2MF
(69)

(7)

(68)
(7)

(68)
(69)

G (17)
5870VB /2MF

(17)

5872VB /2M

(24)
(22)

(68)

ICN-A330-A-27XX3237-A-FAPE3-0137D-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137D-A-001-01 SHEET 6/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 104
 A330
SERVICE BULLETIN

CONF 005
(3) Task A330-A-27-XX-3237-02003-520A-A (A330-A-27-XX-3237-02ZZZ-520Z-A)
Remove the Electrical Harness 5870VB from the structure between FR86 and
FR87 Traverse (with P-Clamps)
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 86 to Frame 87
Manpower/Resources/Skills

Man-hours 2.50 h
Minimum Number of person 1
Elapsed Time 2.50 h
Skills Electrical

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
SRM 51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
4 Tag all the parts you must remove and retain to make the subsequent
installation easier.
5 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
(b) Remove the electrical harness 5870VB between Frame 86 and Frame 87, refer to
Ref. Fig. Remove the Electrical Harness 5870VB from the Structure between FR86
and FR87.
1 Remove, as shown on view D:

2 CLAMP Item (27) Discard

1 CLAMP Item (37) Discard

1 SCREW HEXAGON-HEAD Item (3) Discard

2 SCREW HEXAGON-HEAD Item (4) Discard

3 WASHER Item (7) Discard

2 SPACER Item (65) Discard

REV 00 Oct 12/20 A330-27-3237

Page 105
 A330
SERVICE BULLETIN

1 SPACER Item (8) Discard

1 NUT Item (13) Discard

2 Remove, as shown on view E:

1 CLAMP Item (18) Discard

1 CLAMP Item (37) Discard

1 CLAMP Item (27) Discard

3 SCREW HEXAGON-HEAD Item (3) Discard

2 SCREW HEXAGON-HEAD Item (6) Discard

5 WASHER Item (7) Discard

2 SPACER Item (8) Discard

1 SPACER Item (9) Discard

2 NUT Item (10) Discard

1 NUT Item (13) Discard

3 Remove, as shown on view F:

2 CLAMP Item (16) Discard

1 CLAMP Item (14) Discard

2 SCREW HEXAGON-HEAD Item (6) Discard

2 WASHER Item (7) Discard

1 NUT Item (13) Discard

1 NUT-CLIP, SELF LOCKIN Item (11) Discard

4 Remove, as shown on view G:

1 CLAMP Item (27) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT-CLIP, SELF LOCKIN Item (11) Discard

5 Remove, as shown on view H:

1 CLAMP Item (66) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 SPACER Item (9) Discard

1 NUT-CLIP, SELF LOCKIN Item (11) Discard

6 Remove, as shown on view J:

1 CLAMP Item (14) Discard

REV 00 Oct 12/20 A330-27-3237

Page 106
 A330
SERVICE BULLETIN

1 CLAMP Item (24) Discard

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT Item (10) Discard

7 At FR86, remove, as shown on view K:

1 CLAMP Item (72) Discard

1 BONDING STRIP Item (17) Discard

attached with:

1 SCREW HEXAGON-HEAD Item (6) Discard

1 WASHER Item (7) Discard

1 NUT Item (10) Discard

REV 00 Oct 12/20 A330-27-3237

Page 107
 A330
SERVICE BULLETIN

CONF 005

Z310

FR91

FR87

FR86

FR85

FR84
FR83
FR80 /82

5870VB /2MF

ICN-A330-A-27XX3237-A-FAPE3-0135Y-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0135Y-A-001-01 SHEET 1/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 108
 A330
SERVICE BULLETIN

CONF 005

TO
5949VC H
5204VC
5205VC

J
F
5393VN /B2
FR87
C 5374VN /DC2
TO
1CSK 1CSD 5870VB /2MF

1CSH
D
FR86
TO
5200VP

FR85

ICN-A330-A-27XX3237-A-FAPE3-0135Z-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0135Z-A-003-01 SHEET 2/6

REV 00 Oct 12/20 A330-27-3237
Remove the Electrical Harness 5870VB from the Structure between FR86 and FR87
Page 109
 A330
SERVICE BULLETIN

CONF 005

FR87

5870VB /2MF

1CSD
1CSK

5393VN /B2
5374VN /DC2

TO
1CSH

ICN-A330-A-27XX3237-A-FAPE3-01360-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01360-A-002-01 SHEET 3/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 110
 A330
SERVICE BULLETIN

CONF 005

(3)
(7) (37)

5870VB /2MF
(4)
(8)
(7)
(4) (27)

(7)
01
(27)

(65) (13)

(65)

D
FR87

FR87
5393VN /B2

(3) 5374VN /DC2

5870VB /2MF
(7)
(6)
(7)
(3)
(7)

(18) (9)

5870VB /2MF (8) (27)

(7)
(8) (3)
(10)

(37)

(13)
E

NOTE:
01 DISCONNECTED WITH CABLE HARNESS 5869VB
ICN-A330-A-27XX3237-A-FAPE3-01361-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01361-A-002-01 SHEET 4/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 111
 A330
SERVICE BULLETIN

CONF 005

(13)

FR87

(11)

(14)

(16)

(16) 5870VB /2MF

FR87
(7)

F
(6)

5870VB /2MF

(6)
(7)

(27)

G
(11)

ICN-A330-A-27XX3237-A-FAPE3-01362-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01362-A-002-01 SHEET 5/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 112
 A330
SERVICE BULLETIN

CONF 005

FR87
5870VB /2MF

(66)

(6)
(7)

(9) (10)

(14)
5870VB /2MF
(11)

H
(24) 5872VB /2M

(7)

(6)
FR86

J
(17)

(6)
(7)

(72)

(10) 5870VB /2MF

( 5872VB /2M )

ICN-A330-A-27XX3237-A-FAPE3-01363-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01363-A-002-01 SHEET 6/6

REV 00 Oct 12/20 Remove the Electrical Harness 5870VB A330-27-3237
from the Structure between FR86 and FR87 Page 113
 A330
SERVICE BULLETIN

CONF 001 005

(4) Task A330-A-27-XX-3237-08001-920A-A (A330-A-27-XX-3237-08ZZZ-920Z-A)
Modify the Traverse Structure at FR87
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310
Manpower/Resources/Skills

Man-hours 4.00 h
Minimum Number of person 1
Elapsed Time 4.00 h
Skills Airframe
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04CMA2 Wash Primer - - - Structure
Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure
Polysulfide Sealant -
06AAC1
General Purpose Interfay
Non Aqueous Cleaner -
08BAA9
General
14SBA1 Textile - Lint free Cotton

Part kit 273237D01R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
30 MS21047L3 2 NUT
108 EN6081D5-06 4 RIVET
109 F5398895403200 1 BRACKET
110 EN6101AD3-03 4 RIVET
111 NAS1149C0363R 1 WASHER
113 D9249171620200 2 BRACKET
114 EN6081AD4-08 6 RIVET
115 MS21043-3 2 NUT
116 NSA5067-08-1 2 NUT
117 F5398895426400 1 BRACKET
118 NAS1149D0332K 4 WASHER
119 NAS6703-3 2 BOLT

REV 00 Oct 12/20 A330-27-3237

Page 114
 A330
SERVICE BULLETIN

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
51-24-00
51-42-00
SRM
51-44-00
51-75-12
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
4 Renew the protective finish in accordance with Ref. SRM 51-75-12.
5 Apply sealant in accordance with Ref. SRM 51-24-00.
6 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
7 Get fastener hole diameters and drill data in accordance with Ref. SRM 51-
44-00.
(b) Remove, refer to Ref. Fig. Modification of the Traverse Structure, SHEET 01 and
SHEET 02, view B:

1 NUT Item (30) Discard

attached with

2 RIVET Item (110) Discard

(c) Do the modification of the traverse structure, refer to Ref. Fig. Modification of the
Traverse Structure.
1 Temporarily put the nuts, item 30, in position as shown on view D.
2 Transfer drill the fastener holes from the nuts, item 30, to the structure on
Frame 87 in accordance with Ref. SRM 51-44-00 as shown on view D.
3 Ream the holes to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on view D.
4 Remove the nuts, item 30.
5 Deburr the holes.
6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Cut the area of flange as shown on view E and view F.

REV 00 Oct 12/20 A330-27-3237

Page 115
 A330
SERVICE BULLETIN

8 Temporarily put the bracket, item 109, in position as shown on view D.

9 Transfer drill the fastener holes from the bracket assy, item 109 to the
structure on Frame 87 in accordance with Ref. SRM 51-44-00 as shown on
view D.
10 Ream the holes to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on view D.
11 Remove the bracket, item 109.
12 Deburr the holes.
13 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
14 Renew the protective finish, in accordance with Ref. SRM 51-75-12, with:

Wash Primer - - - 04CMA2

Structure
and

Primer Polyurethane 04EAC2

Paint - -
CorrosionInhibiting
Structure
and

Top Coat Polyurethane - 04JME4

- Grey InternalStructure
(d) Install the bracket, item 109, on Frame 87, refer to Ref. Fig. Modification of the
Traverse Structure, view C.

1 BRACKET ASSY F5398895403200 Item 109

4 RIVET EN6081D5-06 Item 108

1 WASHER NAS1149C0363R Item 111

1 Apply on the washer:

Polysulfide Sealant 06AAC1

- General Purpose
Interfay
(e) Install, on Frame 87, refer to Ref. Fig. Modification of the Traverse Structure, view
C:

2 NUT MS21047L3 Item 30

with

4 RIVET EN6101AD3-03 Item 110

(f) Install the brackets, item 113 and item 117, refer to Ref. Fig. Modification of the
Traverse Structure.
1 Temporarily put the bracket, item 113, in position as shown on view H.

REV 00 Oct 12/20 A330-27-3237

Page 116
 A330
SERVICE BULLETIN

2 Transfer drill the fastener holes from the bracket, item 113, to the structure
on Frame 87 in accordance with Ref. SRM 51-44-00 as shown on view H.
3 Ream the holes to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on view H.
4 Remove the bracket, item 113.
5 Deburr the holes.
6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Preassemble the brackets, item 117 and item 113, as shown on view G.
a Assemble:

1 BRACKET F5398895426400 Item 117

2 BRACKET-Z D9249171620200 Item 113

with

2 NUT-CLIP NSA5067-08-1 Item 116

2 BOLT NAS6703-3 Item 119

4 WASHER NAS1149D0332K Item 118

2 NUT MS21043-3 Item 115

b Torque the nuts, item 115, to between 0.37 and 0.48 m.daN (32.70
and 42.5 lbf.in).
8 Install the preassembled brackets, item 113 and item 117, on Frame 87 as
shown on view H, with:

6 RIVET EN6081AD4-08 Item 114

REV 00 Oct 12/20 A330-27-3237

Page 117
 A330
SERVICE BULLETIN

CONF 001 005

Z310
G H

FR87

FR86

B C D

ICN-A330-A-27XX3237-A-FAPE3-0138A-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138A-A-003-01 SHEET 1/6

REV 00 Oct 12/20 A330-27-3237
Modification of the Traverse Structure
Page 118
 A330
SERVICE BULLETIN

CONF 001 005

BEFORE
(110)

MODIFIED AREA

(30)

FR87

ICN-A330-A-27XX3237-A-FAPE3-0138B-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138B-A-003-01 SHEET 2/6

REV 00 Oct 12/20 A330-27-3237
Modification of the Traverse Structure
Page 119
 A330
SERVICE BULLETIN

CONF 001 005

A
AFTER

108

01 111

80 mm 109
(3.150 in) A 110

110
32.5 mm
(1.280 in)

01 111 30

30

0.2 mm C
109 (0.008 in)

A A
FWD

NOTE:
ELECTRICAL BONDING
01 BOND THE WASHER, ITEM 111,
WITH SEALANT, MATERIAL No 06AAC1
ICN-A330-A-27XX3237-A-FAPE3-0138C-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138C-A-002-01 SHEET 3/6

REV 00 Oct 12/20 A330-27-3237
Modification of the Traverse Structure
Page 120
 A330
SERVICE BULLETIN

CONF 001 005

10 mm 5.1 mm
DIA DIA
(0.394 in) (0.201 in)
5.1 mm
DIA
(0.201 in) 30.8 mm
100 mm (1.213 in)
(3.937 in) 11.7 mm
E F
(0.461 in)
11.7 mm
(0.461 in) FR87

22 mm 30
(0.866 in) 19 mm 6 mm
30 (0.236 in) 109
(0.748 in) DIA 5.1 mm
(0.201 in) 27.1 mm 11 mm
(1.067 in) (0.433 in)
D 50.4 mm
(1.984 in)
VIEW LOOKING FWD

MODIFIED AREA 30 mm
30 mm R
R (1.181 in)
(1.181 in) CUTLINE

5.5 mm 56.5 mm
(0.217 in) (2.224 in)
80 mm
(3.150 in)
50 mm
R
(1.969 in) 103.5 mm
(4.075 in)
F
W
D E
32.5 mm
(1.280 in)

109 80 mm
(3.150 in)
F
NOTE: W
ELECTRICAL BONDING
D F
FOR FASTENER SYMBOL, REFER TO SHEET 06
ICN-A330-A-27XX3237-A-FAPE3-0138D-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138D-A-003-01 SHEET 4/6

REV 00 Oct 12/20 A330-27-3237
Modification of the Traverse Structure
Page 121
 A330
SERVICE BULLETIN

CONF 001 005

FR87

113

114 x3
115 02

113
117 118

118 115 02
119 116 114 x3 118

116

118
119
G

NOTE:
02 TORQUE VALUE BETWEEN MIN 0.37 m.daN (32.7 lbf.in)
AND MAX 0.48 m.daN (42.5 lbf.in)
ICN-A330-A-27XX3237-A-FAPE3-013ES-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013ES-A-003-01 SHEET 5/6

REV 00 Oct 12/20 A330-27-3237
Modification of the Traverse Structure
Page 122
 A330
SERVICE BULLETIN

CONF 001 005

110 mm
(4.331 in)

113 113
34.5 mm
(1.358 in)

117 18.9 mm
(0.744 in)
H
VIEW LOOKING FWD

FINAL
HOLE NEW HOLE DIAMETER
PART NUMBER DESCRIPTION SIZE/FIT TYPE
SYMBOL ITEM
MIN MAX
4.060 mm 4.170 mm
108 EN6081D5-06 RIVET (0.1599 in) (0.1641 in) NOMINAL SIZE
2.460 mm 2.570 mm
110 EN6101AD3-03 RIVET (0.0969 in) (0.1011 in) NOMINAL SIZE
3.250 mm 3.350 mm
114 EN6081AD4-08 RIVET (0.1280 in) (0.1318 in) NOMINAL SIZE

ICN-A330-A-27XX3237-A-FAPE3-013SK-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013SK-A-001-01 SHEET 6/6

REV 00 Oct 12/20 A330-27-3237
Modification of the Traverse Structure
Page 123
 A330
SERVICE BULLETIN

CONF 002
(4) Task A330-A-27-XX-3237-08002-920A-A (A330-A-27-XX-3237-08ZZZ-920Z-A)
Modify the V-Prop Structure at FR87
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310
Manpower/Resources/Skills

Man-hours 4.00 h
Minimum Number of person 1
Elapsed Time 4.00 h
Skills Airframe
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Non Aqueous Cleaner -
08BAA9
General
14SBA1 Textile - Lint free Cotton

Part kit 273237D04R01

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
30 MS21047L3 1 NUT
47 F5397083300000 1 SECTION
48 D9249171620000 1 BRACKET
49 EN6081AD4-06 5 RIVET
52 EN6081AD4-07 4 RIVET
55 EN6101AD3-04 2 RIVET
141 F5398895427600 1 BRACKET
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
51-24-00
51-42-00
SRM
51-44-00
51-75-12
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.

REV 00 Oct 12/20 A330-27-3237

Page 124
 A330
SERVICE BULLETIN

2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
4 Renew the protective finish in accordance with Ref. SRM 51-75-12.
5 Apply sealant in accordance with Ref. SRM 51-24-00.
6 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
7 Get fastener hole diameters and drill data in accordance with Ref. SRM 51-
44-00.
(b) Install the section assy, item 47 and bracket, item 48, on Frame 87, refer to Ref.
Fig. Modification of the V-Prop Structure.
1 Temporarily put the section assy and bracket in position as shown on
SHEET 01 and SHEET 02.
2 Transfer drill the fastener holes from section assy, item 47 and bracket,
item 48 to the structure on Frame 87 in accordance with Ref. SRM 51-44-00
as shown on SHEET 02, view B.
3 Ream the holes to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on SHEET 02, view B.
4 Remove the section assy, item 47 and bracket, item 48.
5 Deburr the holes.
6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Install, as shown on view B:

1 SECTION ASSY F5397083300000 Item 47

1 BRACKET-Z D9249171620000 Item 48

with

5 RIVET EN6081AD4-06 Item 49

(c) Install the nut, item 30, on Frame 87, refer to Ref. Fig. Modification of the V-Prop
Structure.
1 Temporarily put the nut in position as shown on SHEET 03.
2 Transfer drill the fastener holes from the nut, item 30 to the structure on
Frame 87 in accordance with Ref. SRM 51-44-00 as shown on SHEET 03,
view D and view E.
3 Ream the holes to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on SHEET 03, view D and view E.
4 Remove the nut, item 30.
5 Deburr the holes.
6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

REV 00 Oct 12/20 A330-27-3237

Page 125
 A330
SERVICE BULLETIN

Non Aqueous Cleaner - 08BAA9

General
7 Install, as shown on view D:

1 NUT MS21047L3 Item 30

with

2 RIVET EN6101AD3-04 Item 55

(d) Remove, refer to Ref. Fig. Modification of the V-Prop Structure, view F:

1 SECTION Item (51) Discard

4 RIVET Item (52) Discard

(e) Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
(f) Install the bracket, item 141, on Frame 87, refer to Ref. Fig. Modification of the V-
Prop Structure.
1 Temporarily put the bracket in position as shown on SHEET 04, view G.
2 Transfer drill one fastener hole from the bracket, item 141, to the structure
on Frame 87 in accordance with Ref. SRM 51-44-00 as shown on SHEET 04,
view G.
3 Ream the hole to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on SHEET 04, view G.
4 Remove the bracket, item 141.
5 Deburr the hole.
6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Install, as shown on view G:

1 BRACKET F5398895427600 Item 141

with

4 RIVET EN6081AD4-07 Item 52

REV 00 Oct 12/20 A330-27-3237

Page 126
 A330
SERVICE BULLETIN

CONF 002

Z310

FR87
B C

F G D

FR86

FR85

ICN-A330-A-27XX3237-A-FAPE3-0144W-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144W-A-001-01 SHEET 1/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 127
 A330
SERVICE BULLETIN

CONF 002

FR87 78 mm
(3.071 in)

48

10 mm
(0.393 in)
49
47 B
49
FR87

48

25 mm
C (0.984 in)
37.7 mm
VIEW LOOKING AFT 47 (1.484 in)

NOTE:
FOR FASTENER SYMBOL, REFER TO SHEET 05 ICN-A330-A-27XX3237-A-FAPE3-0144X-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144X-A-001-01 SHEET 2/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 128
 A330
SERVICE BULLETIN

CONF 002
FR87

55

30

01
6 mm 5.10 mm
DIA
(0.236 in) (0.201 in)

11 mm
(0.433 in)

5.10 mm
83 mm (0.201 in) 78 mm
(3.268 in) (3.071 in)

01
01 6 mm 6 mm
(0.236 in) E (0.236 in)
NOTE:
VIEW LOOKING FWD
ELECTRICAL BONDING
FOR FASTENER SYMBOL, REFER TO SHEET 05
01 EXISTING HOLE ICN-A330-A-27XX3237-A-FAPE3-0144Y-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144Y-A-001-01 SHEET 3/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 129
 A330
SERVICE BULLETIN

CONF 002

BEFORE FR87

FR87

AFTER

(51)
(52)
141 F

01

52
02

NOTE:
FOR FASTENER SYMBOL, REFER TO SHEET 05
01 EXISTING HOLE
02 TRANSFER-DRILL THE HOLE AT ASSEMBLY ICN-A330-A-27XX3237-A-FAPE3-0144Z-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144Z-A-001-01 SHEET 4/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 130
 A330
SERVICE BULLETIN

CONF 002

FINAL
HOLE NEW HOLE DIAMETER
PART NUMBER DESCRIPTION SIZE/FIT TYPE
SYMBOL ITEM
MIN MAX
3.250 mm 3.350 mm
49 EN6081AD4-06 RIVET (0.1280 in) (0.1318 in) NOMINAL SIZE
3.250 mm 3.350 mm
52 EN6081AD4-07 RIVET (0.1280 in) (0.1318 in) NOMINAL SIZE
2.460 mm 2.570 mm
55 EN6101AD3-04 RIVET (0.0969 in) (0.1011 in) NOMINAL SIZE

ICN-A330-A-27XX3237-A-FAPE3-01450-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01450-A-001-01 SHEET 5/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 131
 A330
SERVICE BULLETIN

CONF 003
(4) Task A330-A-27-XX-3237-08003-920A-A (A330-A-27-XX-3237-08ZZZ-920Z-A)
Modify the V-Prop Structure at FR87
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310
Manpower/Resources/Skills

Man-hours 4.00 h
Minimum Number of person 1
Elapsed Time 4.00 h
Skills Airframe
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Non Aqueous Cleaner -
08BAA9
General
14SBA1 Textile - Lint free Cotton

Part kit 273237D08R00

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
30 MS21047L3 1 NUT
47 F5397083300000 1 SECTION
48 D9249171620000 1 BRACKET
49 EN6081AD4-06 5 RIVET
50 F5398895427400 1 BRACKET
52 EN6081AD4-07 3 RIVET
53 DAN7-6-7X 2 PIN
54 DAN12-6X 2 COLLAR
55 EN6101AD3-04 2 RIVET
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
51-24-00
51-42-00
SRM
51-44-00
51-75-12
Procedure
(a) Standard Practices given in this procedure:

REV 00 Oct 12/20 A330-27-3237

Page 132
 A330
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
4 Renew the protective finish in accordance with Ref. SRM 51-75-12.
5 Apply sealant in accordance with Ref. SRM 51-24-00.
6 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
7 Get fastener hole diameters and drill data in accordance with Ref. SRM 51-
44-00.
(b) Install the section assy, item 47 and bracket, item 48, on Frame 87, refer to Ref.
Fig. Modification of the V-Prop Structure.
1 Temporarily put the section assy and bracket in position as shown on view
B.
2 Transfer drill the fastener holes from the section assy, item 47 and bracket,
item 48, to the structure on Frame 87 in accordance with Ref. SRM 51-44-
00 as shown on view B.
3 Ream the holes to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on view B.
4 Remove the section assy, item 47 and bracket, item 48.
5 Deburr the holes.
6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Install, as shown on view B:

1 SECTION ASSY F5397083300000 Item 47

1 BRACKET-Z D9249171620000 Item 48

with

5 RIVET EN6081AD4-06 Item 49

(c) Install the nut, item 30, on Frame 87, refer to Ref. Fig. Modification of the V-Prop
Structure.
1 Temporarily put the nut in position as shown on SHEET 03.
2 Transfer drill the fastener holes from the nut, item 30 to the structure on
Frame 87 in accordance with Ref. SRM 51-44-00 as shown on SHEET 03,
view D and view E.
3 Ream the holes to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on SHEET 03, view D and view E.
4 Remove the nut, item 30.
5 Deburr the holes.

REV 00 Oct 12/20 A330-27-3237

Page 133
 A330
SERVICE BULLETIN

6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Install, as shown on view E:

1 NUT MS21047L3 Item 30

with

2 RIVET EN6101AD3-04 Item 55

(d) Remove, refer to Ref. Fig. Modification of the V-Prop Structure, SHEET 04, view F:

1 SECTION Item (112) Discard

4 RIVET Item (52) Discard

(e) Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
(f) Install the bracket, item 50, on Frame 87, refer to Ref. Fig. Modification of the V-
Prop Structure.
1 Temporarily put the bracket in position as shown on SHEET 04, view G.
2 Transfer drill one fastener hole from the bracket, item 50 to the structure
on Frame 87 in accordance with Ref. SRM 51-44-00 as shown on SHEET 04,
view G.
3 Ream the hole to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on SHEET 04, view G.
4 Remove the bracket, item 50.
5 Deburr the hole.
6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Install, as shown on view G:

1 BRACKET F5398895427400 Item 50

with

3 RIVET EN6081AD4-07 Item 52

2 PIN-RIVET DAN7-6-7X Item 53

2 COLLAR DAN12-6X Item 54

REV 00 Oct 12/20 A330-27-3237

Page 134
 A330
SERVICE BULLETIN

CONF 003

Z310

FR87
B C

F G D

FR86

FR85

ICN-A330-A-27XX3237-A-FAPE3-0144R-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144R-A-001-01 SHEET 1/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 135
 A330
SERVICE BULLETIN

CONF 003

FR87 78 mm
(3.071 in)

48

10 mm
(0.393 in)
49
47 B
49
FR87

48

25 mm
C (0.984 in)
37.7 mm
47 (1.484 in)
VIEW LOOKING AFT
NOTE:
FOR FASTENER SYMBOL, REFER TO SHEET 05 ICN-A330-A-27XX3237-A-FAPE3-0144S-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144S-A-001-01 SHEET 2/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 136
 A330
SERVICE BULLETIN

CONF 003
FR87

55

30

01
6 mm 5.10 mm
DIA
(0.236 in) (0.201 in)

11 mm
(0.433 in)

5.10 mm
83 mm (0.201 in) 78 mm
(3.268 in) (3.071 in)

01
01 6 mm 6 mm
(0.236 in) (0.236 in)
E
NOTE:
VIEW LOOKING FWD
ELECTRICAL BONDING
FOR FASTENER SYMBOL, REFER TO SHEET 05
01 EXISTING HOLE ICN-A330-A-27XX3237-A-FAPE3-0144T-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144T-A-001-01 SHEET 3/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 137
 A330
SERVICE BULLETIN

CONF 003

BEFORE
FR87

(112)

(52)
AFTER
FR87

54 x2

F
50

53

01

52

G 02

NOTE:
FOR FASTENER SYMBOL, REFER TO SHEET 05
01 EXISTING HOLE
02 TRANSFER-DRILL THE HOLE AT ASSEMBLY ICN-A330-A-27XX3237-A-FAPE3-0144U-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144U-A-001-01 SHEET 4/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 138
 A330
SERVICE BULLETIN

CONF 003

FINAL
HOLE NEW HOLE DIAMETER
PART NUMBER DESCRIPTION SIZE/FIT TYPE
SYMBOL ITEM
MIN MAX
3.250 mm 3.350 mm
49 EN6081AD4-06 RIVET (0.1280 in) (0.1318 in) NOMINAL SIZE
3.250 mm 3.350 mm
52 EN6081AD4-07 RIVET (0.1280 in) (0.1318 in) NOMINAL SIZE
2.460 mm 2.570 mm
55 EN6101AD3-04 RIVET (0.0969 in) (0.1011 in) NOMINAL SIZE

ICN-A330-A-27XX3237-A-FAPE3-0144V-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144V-A-001-01 SHEET 5/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 139
 A330
SERVICE BULLETIN

CONF 004
(4) Task A330-A-27-XX-3237-08004-920A-A (A330-A-27-XX-3237-08ZZZ-920Z-A)
Modify the V-Prop Structure at FR87
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310
Manpower/Resources/Skills

Man-hours 4.00 h
Minimum Number of person 1
Elapsed Time 4.00 h
Skills Airframe
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Non Aqueous Cleaner -
08BAA9
General
14SBA1 Textile - Lint free Cotton

Part kit 273237D03R01

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
30 MS21047L3 1 NUT
47 F5397083300000 2 SECTION
48 D9249171620000 1 BRACKET
49 EN6081AD4-06 7 RIVET
50 F5398895427400 1 BRACKET
52 EN6081AD4-07 3 RIVET
53 DAN7-6-7X 2 PIN
54 DAN12-6X 2 COLLAR
55 EN6101AD3-04 2 RIVET
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
51-24-00
51-42-00
SRM
51-44-00
51-75-12
Procedure
(a) Standard Practices given in this procedure:

REV 00 Oct 12/20 A330-27-3237

Page 140
 A330
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
4 Renew the protective finish in accordance with Ref. SRM 51-75-12.
5 Apply sealant in accordance with Ref. SRM 51-24-00.
6 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
7 Get fastener hole diameters and drill data in accordance with Ref. SRM 51-
44-00.
(b) Install the section assys, item 47 and bracket, item 48, on Frame 87, refer to Ref.
Fig. Modification of the V-Prop Structure.
1 Temporarily put the section assys and bracket in position as shown on
SHEET 01 and SHEET 02, view B.
2 Transfer drill the fastener holes from the section assys, item 47 and
bracket, item 48 to the structure on Frame 87 in accordance with Ref. SRM
51-44-00 as shown on SHEET 02, view B.
3 Ream the holes to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on SHEET 02, view B.
4 Remove the section assys, item 47 and bracket, item 48.
5 Deburr the holes.
6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Install, as shown on view B:

2 SECTION ASSY F5397083300000 Item 47

1 BRACKET-Z D9249171620000 Item 48

with

7 RIVET EN6081AD4-06 Item 49

(c) Install the nut, item 30, on Frame 87, refer to Ref. Fig. Modification of the V-Prop
Structure.
1 Temporarily put the nut in position as shown on SHEET 03.
2 Transfer drill the fastener holes from the nut, item 30, to the structure on
Frame 87 in accordance with Ref. SRM 51-44-00 as shown on SHEET 03,
view D and view E.
3 Remove the nut, item 30.
4 Ream the holes to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on SHEET 03, view D and view E.
5 Deburr the holes.

REV 00 Oct 12/20 A330-27-3237

Page 141
 A330
SERVICE BULLETIN

6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Install, as shown on view E:

1 NUT MS21047L3 Item 30

with

2 RIVET EN6101AD3-04 Item 55

(d) Remove, refer to Ref. Fig. Modification of the V-Prop Structure, SHEET 04, view F:

1 SECTION Item (112) Discard

4 RIVET Item (52) Discard

(e) Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
(f) Install the bracket, item 50, on Frame 87, refer to Ref. Fig. Modification of the V-
Prop Structure.
1 Temporarily put the bracket in position as shown on SHEET 04, view G.
2 Transfer drill one fastener hole from bracket, item 50 to the structure on
Frame 87 in accordance with Ref. SRM 51-44-00 as shown on SHEET 04,
view G.
3 Ream the hole to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on SHEET 04, view G.
4 Remove the bracket, item 50.
5 Deburr the hole.
6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Install, as shown on view G:

1 BRACKET F5398895427400 Item 50

with

3 RIVET EN6081AD4-07 Item 52

2 PIN-RIVET DAN7-6-7X Item 53

2 COLLAR DAN12-6X Item 54

REV 00 Oct 12/20 A330-27-3237

Page 142
 A330
SERVICE BULLETIN

CONF 004

Z310

FR87
B C

F G D

FR86

FR85

ICN-A330-A-27XX3237-A-FAPE3-0144M-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144M-A-001-01 SHEET 1/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 143
 A330
SERVICE BULLETIN

CONF 004

94 mm
FR87 78 mm
(3.701 in)
(3.071 in)

47

48
10 mm
49
(0.393 in)
47

49
B 49

FR87

48

25 mm
C (0.984 in)
37.7 mm
VIEW LOOKING AFT 47 (1.484 in)
47

NOTE:
FOR FASTENER SYMBOL, REFER TO SHEET 05 ICN-A330-A-27XX3237-A-FAPE3-0144N-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144N-A-001-01 SHEET 2/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 144
 A330
SERVICE BULLETIN

CONF 004
FR87

55

30

01
6 mm 5.10 mm
DIA
(0.236 in) (0.201 in)

11 mm
(0.433 in)

5.10 mm
83 mm (0.201 in) 78 mm
(3.268 in) (3.071 in)

01
01 6 mm 6 mm
(0.236 in) (0.236 in)
E
NOTE:
VIEW LOOKING FWD
ELECTRICAL BONDING
FOR FASTENER SYMBOL, REFER TO SHEET 05
01 EXISTING HOLE ICN-A330-A-27XX3237-A-FAPE3-0144O-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144O-A-001-01 SHEET 3/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 145
 A330
SERVICE BULLETIN

CONF 004
BEFORE FR87

(112)

(52)

FR87

AFTER
54 x2
F

50

53

01

52
G 02

NOTE:
FOR FASTENER SYMBOL, REFER TO SHEET 05
01 EXISTING HOLE
02 TRANSFER-DRILL THE HOLE AT ASSEMBLY ICN-A330-A-27XX3237-A-FAPE3-0144P-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144P-A-001-01 SHEET 4/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 146
 A330
SERVICE BULLETIN

CONF 004

FINAL
HOLE NEW HOLE DIAMETER
PART NUMBER DESCRIPTION SIZE/FIT TYPE
SYMBOL ITEM
MIN MAX
3.250 mm 3.350 mm
49 EN6081AD4-06 RIVET (0.1280 in) (0.1318 in) NOMINAL SIZE
3.250 mm 3.350 mm
52 EN6081AD4-07 RIVET (0.1280 in) (0.1318 in) NOMINAL SIZE
2.460 mm 2.570 mm
55 EN6101AD3-04 RIVET (0.0969 in) (0.1011 in) NOMINAL SIZE

ICN-A330-A-27XX3237-A-FAPE3-0144Q-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0144Q-A-001-01 SHEET 5/5

REV 00 Oct 12/20 A330-27-3237
Modification of the V-Prop Structure
Page 147
 A330
SERVICE BULLETIN

CONF 001 005

(5) Task A330-A-27-XX-3237-02001-720A-A (A330-A-27-XX-3237-02ZZZ-720Z-A)
Install the Brackets at FR87 Traverse
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location Frame 87
Manpower/Resources/Skills

Man-hours 3.00 h
Minimum Number of person 1
Elapsed Time 3.00 h
Skills Airframe
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Non Aqueous Cleaner -
08BAA9
General
14SBA1 Textile - Lint free Cotton

Part kit 273237D01R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
57 F5398895426000 1 BRACKET
58 F5398895426200 1 BRACKET
59 D5357068121400 1 ANGLE
60 EN6081D5-07 8 RIVET
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
51-24-00
51-42-00
SRM
51-44-00
51-75-12
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
4 Renew the protective finish in accordance with Ref. SRM 51-75-12.

REV 00 Oct 12/20 A330-27-3237

Page 148
 A330
SERVICE BULLETIN

5 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
6 Apply sealant in accordance with Ref. SRM 51-24-00.
7 Get fastener hole diameters and drill data in accordance with Ref. SRM 51-
44-00.
(b) Install the electrical brackets between Frame 86 and Frame 87, refer to Ref. Fig.
Installation of the electrical brackets.
1 Temporarily put the brackets in position as shown on view B.
2 Transfer drill the fastener holes from the bracket, item 57, item 58 and
item 59, to the structure on Frame 87 in accordance with Ref. SRM 51-44-
00 as shown on view B.
3 Ream the holes to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on view B.
4 Remove the bracket, item 57, item 58 and item 59.
5 Deburr the holes.
6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Install, as shown on view B:

1 BRACKET F5398895426000 Item 57

1 BRACKET F5398895426200 Item 58

1 ANGLE D5357068121400 Item 59

8 RIVET EN6081D5-07 Item 60

(c) Do the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task 20-28-
00-912-810.

REV 00 Oct 12/20 A330-27-3237

Page 149
 A330
SERVICE BULLETIN

CONF 001 005

Z310
B C

FR87

FR86

ICN-A330-A-27XX3237-A-FAPE3-0135S-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0135S-A-002-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Brackets
Page 150
 A330
SERVICE BULLETIN

CONF 001 005

58
FR87

60 x4
59

57

60 x2

60 x2

B
FR86

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0135T-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0135T-A-002-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Brackets
Page 151
 A330
SERVICE BULLETIN

CONF 001 005

FR87

133.5 mm
160.4 mm (5.256 in) 38.5 mm
(6.315 in) (1.516 in)

58

57

59 12 mm
(0.472 in)
75.5 mm
(2.972 in) 75 mm
(2.953 in)

FR86

F
W
C D

VIEW LOOKING UP
FINAL
HOLE NEW HOLE DIAMETER
PART NUMBER DESCRIPTION SIZE/FIT TYPE
SYMBOL ITEM
MIN MAX
4.060 mm 4.170 mm
60 EN6081D5-07 RIVET (0.1599 in) (0.1641 in) NOMINAL SIZE

ICN-A330-A-27XX3237-A-FAPE3-0135U-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0135U-A-003-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Brackets
Page 152
 A330
SERVICE BULLETIN

CONF 002-004
(5) Task A330-A-27-XX-3237-02002-720A-A (A330-A-27-XX-3237-02ZZZ-720Z-A)
Install the Brackets at FR87 V-Prop
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location Frame 87
Manpower/Resources/Skills

Man-hours 3.00 h
Minimum Number of person 1
Elapsed Time 3.00 h
Skills Airframe
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Non Aqueous Cleaner -
08BAA9
General
14SBA1 Textile - Lint free Cotton

Part kit 273237D02R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
57 F5398895426000 1 BRACKET
58 F5398895426200 1 BRACKET
59 D5357068121400 1 ANGLE
60 EN6081D5-07 8 RIVET
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 20-28-00-912-810
ESPM 20-51-20
51-24-00
51-42-00
SRM
51-44-00
51-75-12
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
4 Renew the protective finish in accordance with Ref. SRM 51-75-12.

REV 00 Oct 12/20 A330-27-3237

Page 153
 A330
SERVICE BULLETIN

5 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
6 Apply sealant in accordance with Ref. SRM 51-24-00.
7 Get fastener hole diameters and drill data in accordance with Ref. SRM 51-
44-00.
(b) Install the brackets between Frame 86 and Frame 87, refer to Ref. Fig.
Installation of the electrical brackets.
1 Temporarily put the brackets in position as shown on view B.
2 Transfer drill the fastener holes from the bracket, item 57, item 58 and
item 59, to the structure on Frame 87 in accordance with Ref. SRM 51-44-
00 as shown on view B.
3 Ream the holes to the diameter given in the fastener table, in accordance
with Ref. SRM 51-44-00 as shown on view B.
4 Remove the bracket, item 57, item 58 and item 59.
5 Deburr the holes.
6 Clean the work area with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
7 Install, as shown on view B:

1 BRACKET F5398895426000 Item 57

1 BRACKET F5398895426200 Item 58

1 ANGLE D5357068121400 Item 59

8 RIVET EN6081D5-07 Item 60

(c) Do the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task 20-28-
00-912-810.

REV 00 Oct 12/20 A330-27-3237

Page 154
 A330
SERVICE BULLETIN

CONF 002-004

Z310

B C
FR87

FR86

FR85

ICN-A330-A-27XX3237-A-FAPE3-0135V-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0135V-A-002-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Brackets
Page 155
 A330
SERVICE BULLETIN

CONF 002-004

58

FR87

60 x4
59

57

60 x2

60 x2

B
FR86

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0135W-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0135W-A-002-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Brackets
Page 156
 A330
SERVICE BULLETIN

CONF 002-004
FR87

131.5 mm
160.4 mm (5.177 in) 48.5 mm
(6.315 in)
(1.909 in)

58

57 12 mm
(0.472 in)
59
75.5 mm 75 mm
(2.972 in) (2.953 in)

FR86

F
W
C D
VIEW LOOKING UP
FINAL
HOLE NEW HOLE DIAMETER
PART NUMBER DESCRIPTION SIZE/FIT TYPE
SYMBOL ITEM
MIN MAX
4.060 mm 4.170 mm NOMINAL
60 EN6081D5-07 RIVET (0.1599 in) (0.1641 in) INTERFERENCE FIT
ICN-A330-A-27XX3237-A-FAPE3-0135X-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0135X-A-003-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Brackets
Page 157
 A330
SERVICE BULLETIN

CONF 001 005

(6) Task A330-A-27-XX-3237-01001-720A-A (A330-A-27-XX-3237-01ZZZ-720Z-A)
Install the Electrical Dummy Connectors at FR87 Traverse
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 86 to Frame 87
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical
Material necessary to do the job
Part kit 273237D01R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
120 NAS1149CN432R 10 WASHER
121 NAS1101-04-6 1 SCREW
122 NAS1101-04-7 9 SCREW
123 MS21042-04 10 NUT
124 EN2997KE510 1 CONNECTR
125 EN2997KE508 1 CONNECTR
126 F9297582000000 1 HARNESS
127 F9249016920000 1 PLATE
128 F9249016920200 1 PLATE
130 EN2997KE3C10 1 CAP

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F9100095127395 1 PLCRDSET (1)
NOTE(S)
(1): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM
Task 11-00-00-400-801
Task 20-28-00-912-810
20-33-00
20-51-20
ESPM
20-52-10
20-54-50
Procedure

REV 00 Oct 12/20 A330-27-3237

Page 158
 A330
SERVICE BULLETIN

(a) Standard Practices given in this procedure:

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
4 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-801.
5 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
6 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
7 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
(b) Install the electrical dummy connectors, refer to Ref. Fig. Installation of the
Electrical Dummy Connectors at FR87.
1 Install, as shown on view B:

FIN 58CSS
1 CONNECTOR- EN2997KE508 Item 125
RECEPTACLE,DUMMY
with

1 PLATE-SPACER F9249016920200 Item 128

4 SCREW NAS1101-04-7 Item 122

4 WASHER NAS1149CN432R Item 120

4 NUT MS21042-04 Item 123

2 Install, as shown on view B:

FIN 58CSR
1 HARNESS ASSY- F9297582000000 Item 126
CABLE,7820VB
with

1 PLATE F9249016920000 Item 127

4 SCREW NAS1101-04-7 Item 122

4 WASHER NAS1149CN432R Item 120

4 NUT MS21042-04 Item 123

3 Install, as shown on view B:

1 CONNECTOR- EN2997KE510 Item 124

RECEPTACLE,DUMMY
with

1 CAP-PROTECTIVE EN2997KE3C10 Item 130

1 SCREW NAS1101-04-7 Item 122

1 SCREW NAS1101-04-6 Item 121

REV 00 Oct 12/20 A330-27-3237

Page 159
 A330
SERVICE BULLETIN

2 WASHER NAS1149CN432R Item 120

2 NUT MS21042-04 Item 123

(c) Bond the placard identified 58CSR and 58CSS, item 140, refer to Ref. Fig.
Installation of the Electrical Dummy Connectors at FR87, view B, supplied in:

1 PLACARD SET F9100095127395

REV 00 Oct 12/20 A330-27-3237

Page 160
 A330
SERVICE BULLETIN

CONF 001 005

Z310
B

7820VB /2MF
FR87

58CS

FR86

ICN-A330-A-27XX3237-A-FAPE3-013A8-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013A8-A-002-01 SHEET 1/2

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Dummy Connectors at FR87
Page 161
 A330
SERVICE BULLETIN

CONF 001 005

7820VB /2MF

123
FR87
124 126

58CS

127

58CSR
140 123 x4

120
121
120
123 x4
125
128

122
130
120 x4
122 x4

140
120 x4 58CSS
122 x4

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-013A9-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013A9-A-002-01 SHEET 2/2

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Dummy Connectors at FR87
Page 162
 A330
SERVICE BULLETIN

CONF 002-004
(6) Task A330-A-27-XX-3237-01002-720A-A (A330-A-27-XX-3237-01ZZZ-720Z-A)
Install the Electrical Dummy Connectors at FR87 V-Prop
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 86 to Frame 87
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical
Material necessary to do the job
Part kit 273237D02R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
120 NAS1149CN432R 10 WASHER
121 NAS1101-04-6 1 SCREW
122 NAS1101-04-7 9 SCREW
123 MS21042-04 10 NUT
124 EN2997KE510 1 CONNECTR
125 EN2997KE508 1 CONNECTR
126 F9297582000000 1 HARNESS
127 F9249016920000 1 PLATE
128 F9249016920200 1 PLATE
130 EN2997KE3C10 1 CAP

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F9100095127395 1 PLCRDSET (1)
NOTE(S)
(1): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 11-00-00-400-801
20-33-00
ESPM 20-52-10
20-54-50
Procedure
(a) Standard Practices given in this procedure:

REV 00 Oct 12/20 A330-27-3237

Page 163
 A330
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
4 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-801.
5 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
6 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
(b) Install the electrical dummy connector, refer to Ref. Fig. Installation of the
Electrical Dummy Connectors at FR87.
1 Install, as shown on view B:

FIN 58CSS
1 CONNECTOR- EN2997KE508 Item 125
RECEPTACLE,DUMMY
with

1 PLATE-SPACER F9249016920200 Item 128

4 SCREW NAS1101-04-7 Item 122

4 WASHER NAS1149CN432R Item 120

4 NUT MS21042-04 Item 123

2 Install, as shown on view B:

FIN 58CSR
1 HARNESS ASSY- F9297582000000 Item 126
CABLE,7820VB
with

1 PLATE F9249016920000 Item 127

4 SCREW NAS1101-04-7 Item 122

4 WASHER NAS1149CN432R Item 120

4 NUT MS21042-04 Item 123

3 Install, as shown on view B:

1 CONNECTOR- EN2997KE510 Item 124

RECEPTACLE,DUMMY
with

1 CAP-PROTECTIVE EN2997KE3C10 Item 130

1 SCREW NAS1101-04-7 Item 122

1 SCREW NAS1101-04-6 Item 121

2 WASHER NAS1149CN432R Item 120

2 NUT MS21042-04 Item 123

REV 00 Oct 12/20 A330-27-3237

Page 164
 A330
SERVICE BULLETIN

(c) Bond the placard identified 58CSR and 58CSS, item 140, refer to Ref. Fig.
Installation of the Electrical Dummy Connectors at FR87, view B, supplied in:

1 PLACARD SET F9100095127395

REV 00 Oct 12/20 A330-27-3237

Page 165
 A330
SERVICE BULLETIN

CONF 002-004

Z310

B
FR87

7820VB /2MF

58CS

FR86

FR85

ICN-A330-A-27XX3237-A-FAPE3-013AA-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013AA-A-001-01 SHEET 1/2

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Dummy Connectors at FR87
Page 166
 A330
SERVICE BULLETIN

CONF 002-004

7820VB /2MF

123
FR87
124 126

58CS

127

58CSR
140 123 x4

120
121
120
123 x4
125
128

122
130
120 x4
122 x4

140
120 x4 58CSS
122 x4

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-013AB-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013AB-A-002-01 SHEET 2/2

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Dummy Connectors at FR87
Page 167
 A330
SERVICE BULLETIN

CONF ALL
(7) Task A330-A-27-XX-3237-01001-760A-A (A330-A-27-XX-3237-01ZZZ-760Z-A)
Reroute the Wire 2499-5020 between FR56 and FR69
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

170
160
150 Work location From Frame 55 to Frame 69
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
ESPM 20-52-21
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Remove the wire 2499–5020 from the cable harness 5871VB in the area between
FR55 and FR69, refer to Ref. Fig. Rerouting of wire 2499-5020 from 3671VC to
FR69, SHEET 01, view B.
(c) Do the re-routing of the wire 2499–5020 from 3671VC to FR69, refer to Ref. Fig.
Rerouting of wire 2499-5020 from 3671VC to FR69, view C.

NOTE: The re-routing of the wire 2499-5020 is detailed in the subtask Ref. Task
A330-A-27-XX-3237-04ZZZ-760Z-A.

(d) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Oct 12/20 A330-27-3237

Page 168
 A330
SERVICE BULLETIN

CONF ALL

BEFORE
A C

Z170
Z160
Z150

5205VP

FR56

5871VB FR69

FR55 B
5871VB 01
WIRE 2499-5020 A
01
3671VC
B 3671VC
NOTE:
01 REMOVE WIRE 2499-5020 FROM CABLE HARNESS 5871VB
IN THE AREA BETWEEN FR55 AND FR69 FR56 FR55
ICN-A330-A-27XX3237-A-FAPE3-0139X-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139X-A-002-01 SHEET 1/2

REV 00 Oct 12/20 A330-27-3237
Rerouting of wire 2499-5020 from 3671VC to FR69
Page 169
 A330
SERVICE BULLETIN

CONF ALL

AFTER

5869VB
5205VP

FR69

5000VE

5871VB
C

3671VC

FR56 FR55
ICN-A330-A-27XX3237-A-FAPE3-013R9-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013R9-A-001-01 SHEET 2/2

REV 00 Oct 12/20 A330-27-3237
Rerouting of wire 2499-5020 from 3671VC to FR69
Page 170
 A330
SERVICE BULLETIN

CONF 001-004
(8) Task A330-A-27-XX-3237-03001-920A-A (A330-A-27-XX-3237-03ZZZ-920Z-A)
Modify the C/B-Box 5000VE
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

Door 823
Access
160 Panel 162KW, Panel 162RW
Work location From Frame 65 to Frame 73
Manpower/Resources/Skills

Man-hours 4.00 h
Minimum Number of person 1
Elapsed Time 4.00 h
Skills Electrical
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Non Aqueous Cleaner -
08BAA9
General
Wire - Locking Dia: 0.6 mm
14QEB1
CRES Nickel Alloy
14SBA1 Textile - Lint free Cotton

Part kit 273237D05R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
32 NAS1100-06-10 4 SCREW
56 NAS1149CN616R 4 WASHER
62 ABS0772A01A 1 CLIP
99 NSA931320-030 1 CB
134 NSA939526-03C 1 SHUNT
136 G9297006500400 1 EQUIPMNT
F9237000703600 1 PLCRDSET
F9237000704000 1 PLCRDSET
F9237000704200 1 PLCRDSET

Re-identified Part Set

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
33 F9259001300800 PANEL (33) F9259001300600
33 F9259001301000 PANEL (33) F9259001300400
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
06-41-53, Page Block 001
REV 00 Oct 12/20 A330-27-3237
Page 171
 A330
SERVICE BULLETIN

Manuals/Drawings References/Sheets
Task 31-18-51-000-801
Task 31-18-51-400-801
AWM 27-98-08
20-33-00
ESPM
20-52-21
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
(b) Remove the APU starter box, refer to Ref. AMM Task 31-18-51-000-801.
(c) Modify the C/B-Box 5000VE, refer to Ref. Fig. Modification of the CB-Box 5000VE.
1 Remove, as shown on view B:

1 PANEL-FRONT F9259001300400 Item (33) Retain

or

1 PANEL-FRONT F9259001300600 Item (33) Retain

attached with:

4 SCREW Item (32) Discard

4 WASHER Item (56) Discard

2 Drill the hole in the panel, item (33), to the given dimensions, as shown on
view C.
3 Deburr the hole.
4 Clean the work area for bonding with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
5 Bond the placard identified as ELSD, item 135, on the plate, as shown on
view C, supplied in:

1 PLACARD SET F9237000704200

6 Use indelible ink to write the required information on the identification
plate,
7 Re-identify the front plate:

1 PANEL-FRONT F9259001300400 Item (33)

becomes

1 PANEL-FRONT F9259001301000 Item 33

or

1 PANEL-FRONT F9259001300600 Item (33)

REV 00 Oct 12/20 A330-27-3237

Page 172
 A330
SERVICE BULLETIN

becomes

1 PANEL-FRONT F9259001300800 Item 33

(d) Remove, refer to Ref. Fig. Modification of the CB-Box 5000VE, view E:

1 SHUNT Item (132) Discard

(e) Install the C/B (FIN 59CS), refer to Ref. Fig. Modification of the CB-Box 5000VE,
view F and view G.
1 Install:

FIN 59CS
1 CIRCUIT BREAKER NSA931320-030 Item 99
2 Torque the screws to between 0.17 and 0.18 m.daN (15.00 and 15.90
lbf.in).
3 Torque the nut to between 0.45 and 0.50m.daN(39.84 and 44.16 lbf.in).
4 Install:

1 SHUNT NSA939526-03C Item 134

1 EQUIPMENT ASSY- G9297006500400 Item 136

ELECTRICAL

1 CLIP-LOCKING ABS0772A01A Item 62

5 Safety the locking clip with:

Wire - Locking Dia: 0.6 14QEB1

mm CRES Nickel Alloy
(f) Modify the wiring.
Refer to Ref. ESPM 20-33-00
1 Remove the shunt as shown on this(these) wiring diagram(s):
- Ref. Fig. Wiring Diagram - Modification of the wiring in CB-Box
5000VE.
2 Install the wire and new shunt as shown on this (these) wiring diagram(s)
and the related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Modification of the wiring in CB-Box 5000VE
and Ref. Fig. Hook-up Chart of the Modification of the Wiring in CB-
Box 5000VE
Ref. AWM 27-98-08.
3 Do a continuity test of the new and/or modified electrical wires, refer to
Ref. ESPM 20-52-21.
(g) Adjacent to the C/B, bond the placard identified as 59CS, item 133, supplied in:

1 PLACARD SET F9237000704000

(h) Install, refer to Ref. Fig. Modification of the CB-Box 5000VE, view D:

1 PANEL-FRONT F9259001300800 Item 33

or

1 PANEL-FRONT F9259001301000 Item 33

with

4 SCREW NAS1100-06-10 Item 32

REV 00 Oct 12/20 A330-27-3237
Page 173
 A330
SERVICE BULLETIN

4 WASHER NAS1149CN616R Item 56

(i) Clean the work area for bonding with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
(j) Bond the Service Bulletin placard identified as SB27–3237, item 74, refer to Ref.
Fig. Modification of the CB-Box 5000VE, view D, supplied in:

1 PLACARD SET F9237000703600

(k) Install the APU starter box, refer to Ref. AMM Task 31-18-51-400-801.

REV 00 Oct 12/20 A330-27-3237

Page 174
 A330
SERVICE BULLETIN

CONF 001-004
FR73

A Z160

FR65

5000VE

5112VCA

E F

B D

(181)

A
5000VE

ICN-A330-A-27XX3237-A-FAPE3-0139Y-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139Y-A-001-01 SHEET 1/5

REV 00 Oct 12/20 A330-27-3237
Modification of the CB-Box 5000VE
Page 175
 A330
SERVICE BULLETIN

CONF 001-004

BEFORE

(56) x4

(32) x4

(33)
B

APU
(33) COM
33 MAIN MODE INTRPT 31.5 mm
ELSD CTL SUPPLY SUPPLY SUPPLY (1.240 in)
135

17 mm
DIA
(0.669 in)

C
26 mm 20 mm ± 0.2 VIEW LOOKING AFT
(1.024 in) (0.787 in ±0.008)
ICN-A330-A-27XX3237-A-FAPE3-0139Z-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139Z-A-002-01 SHEET 2/5

REV 00 Oct 12/20 A330-27-3237
Modification of the CB-Box 5000VE
Page 176
 A330
SERVICE BULLETIN

CONF 001-004

99
AFTER

G
01

01 03

74 SB27-3237
IMPLEMENTED

02

32 x4

33
D
NOTE: 56 x4
01 PART OF CIRCUIT BREAKER , ITEM 99
02 RE-IDENTIFY FRONTPLATE WITH INDELIBLE INK:
OLD PART NUMBER NEW PART NUMBER
F925-90013-004-00 F925-90013-010-00
F925-90013-006-00 F925-90013-008-00
03 TORQUE VALUE BETWEEN 0.45 m.daN (39.84 lbf.in) AND 0.50 m.daN (44.16 lbf.in)
ICN-A330-A-27XX3237-A-FAPE3-013A0-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013A0-A-002-01 SHEET 3/5

REV 00 Oct 12/20 A330-27-3237
Modification of the CB-Box 5000VE
Page 177
 A330
SERVICE BULLETIN

CONF 001-004
BEFORE 1KD

2KD

(132)

01

01
01

AFTER

5112VC

136 05

133 59CS
E
99 59CS
2KD
134
1KD 01

01

01 04
01 04
01

NOTE:
01 PART OF CIRCUIT BREAKER,
ITEM 99
04 TORQUE VALUE BETWEEN
MIN 0.17 m.daN (15.0 lbf.in) AND
MAX 0.18 m.daN (15.9 lbf.in) F
05 ATTACH TO EXISTING
ELECTRICAL HARNESS
WITH CABLE TIES,
ITEM 61, AS NECESSARY
ICN-A330-A-27XX3237-A-FAPE3-013A1-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013A1-A-001-01 SHEET 4/5

REV 00 Oct 12/20 A330-27-3237
Modification of the CB-Box 5000VE
Page 178
 A330
SERVICE BULLETIN

CONF 001-004

EL
SD
CT
L
99
59CS

62

63
G

ICN-A330-A-27XX3237-A-FAPE3-013A2-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013A2-A-001-01 SHEET 5/5

REV 00 Oct 12/20 A330-27-3237
Modification of the CB-Box 5000VE
Page 179
 A330
SERVICE BULLETIN

CONF 001-004

BEFORE

5 10
2 1 2 1
3 3

5 5

2KD 1KD
CTL MAIN
SUPPLY
5112VC-A -A

5112VC
AFTER

6146-DR18
01

1MF
3 5 10
2 1 2 1 2 1
3 3

59CS
ELSD 5 5

2KD 1KD
NEW WIRE, NEW SHUNT
CTL MAIN
DELETED SHUNT SUPPLY

NOTE:
UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA No 3118 NOTE:
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE IN 5000VE 01 NEW SHUNT IS NECESSARY : SEE MODIFICATION OF CB-BOX 5000VE
ICN-A330-A-27XX3237-A-FAPE3-0139R-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139R-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Modification of the Wiring in CB-Box 5000VE
Page 180
 A330
SERVICE BULLETIN

CONF 001-004

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
ZONE OR ELEC. WIRE ZONE OR ELEC.
E TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 162 59CS ELSD 2 NSA936501TA1603 3118- 6146 1MF DR18 1000 40 162 5112VC -A EN3155-019F2018 A <1>

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
<1> PAX ELT.EQUIPMENT G9297006500200 "SHEET 06,ISSUE C"
D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C1-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in CB-Box 5000VE
Page 181
 A330
SERVICE BULLETIN

CONF 005
(8) Task A330-A-27-XX-3237-03014-920A-A (A330-A-27-XX-3237-03ZZZ-920Z-A)
Modify the C/B-Box 5000VE
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

160 Work location From Frame 65 to Frame 73
Manpower/Resources/Skills

Man-hours 4.00 h
Minimum Number of person 1
Elapsed Time 4.00 h
Skills Electrical
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Non Aqueous Cleaner -
08BAA9
General
Wire - Locking Dia: 0.6 mm
14QEB1
CRES Nickel Alloy
14SBA1 Textile - Lint free Cotton

Part kit 273237D06R04

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
32 NAS1100-06-10 4 SCREW
56 NAS1149CN616R 4 WASHER
62 ABS0772A01A 1 CLIP
99 NSA931320-030 1 CB
134 NSA939526-03C 1 SHUNT
136 G9297006500600 1 EQUIPMNT
F9237000703600 1 PLCRDSET
F9237000704000 1 PLCRDSET
F9237000704200 1 PLCRDSET

Re-identified Part Set

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
33 F9259001300800 PANEL (33) F9259001300600
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM 06-41-53, Page Block 001
Task 31-18-51-000-801
Task 31-18-51-400-801
AWM 27-98-08

REV 00 Oct 12/20 A330-27-3237

Page 182
 A330
SERVICE BULLETIN

Manuals/Drawings References/Sheets
20-33-00
ESPM
20-52-21
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
(b) Remove the APU starter box, refer to Ref. AMM Task 31-18-51-000-801.
(c) Modify the C/B-Box 5000VE, refer to Ref. Fig. Modification of the CB-Box 5000VE.
1 Remove, as shown on view B:

1 PANEL-FRONT F9259001300600 Item (33) Retain

4 SCREW Item (32) Discard

4 WASHER Item (56) Discard

2 Drill the hole in the panel, item (33), to the given dimensions, as shown on
view C.
3 Deburr the hole.
4 Clean the work area for bonding with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
5 Bond the placard identified as ELSD, item 135, on the plate, as shown on
view C, supplied in:

1 PLACARD SET F9237000704200

6 Use indelible ink to write the required information on the identification
plate,
7 Re-identify the front plate:

1 PANEL-FRONT F9259001300600 Item (33)

becomes

1 PANEL-FRONT F9259001300800 Item 33

(d) Remove, refer to Ref. Fig. Modification of the CB-Box 5000VE, view E:

1 SHUNT Item (132) Discard

(e) Install the C/B (FIN 59CS), refer to Ref. Fig. Modification of the CB-Box 5000VE,
view F and view G.
1 Install:

FIN 59CS
1 CIRCUIT BREAKER NSA931320-030 Item 99

REV 00 Oct 12/20 A330-27-3237

Page 183
 A330
SERVICE BULLETIN

2 Torque the screws to between 0.17 and 0.18 m.daN (15.00 and 15.90lbf.in).
3 Torque the nut to between 0.45 and 0.50m.daN(39.84 and 44.16lbf.in).
4 Install:

1 SHUNT NSA939526-03C Item 134

1 EQUIPMENT ASSY- G9297006500600 Item 136

ELECTRICAL

1 CLIP-LOCKING ABS0772A01A Item 62

5 Safety the locking clip with:

Wire - Locking Dia: 0.6 14QEB1

mm CRES Nickel Alloy
(f) Modify the wiring.
Refer to Ref. ESPM 20-33-00
1 Remove the shunt as shown on this(these) wiring diagram(s):
- Ref. Fig. Wiring Diagram - Modification of the wiring in CB-Box
5000VE.
2 Install the wire and new shunt as shown on this (these) wiring diagram(s)
and the related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Modification of the wiring in CB-Box 5000VE
and Ref. Fig. Hook-up Chart of the Modification of the Wiring in CB-
Box 5000VE
Ref. AWM 27-98-08.
3 Do a continuity test of the new and/or modified electrical wires, refer to
Ref. ESPM 20-52-21.
(g) Adjacent to the C/B, bond the placard identified as 59CS, item 133, supplied in:

1 PLACARD SET F9237000704000

(h) Install, refer to Ref. Fig. Modification of the CB-Box 5000VE, view D:

1 PANEL-FRONT F9259001300800 Item 33

with

4 SCREW NAS1100-06-10 Item 32

4 WASHER NAS1149CN616R Item 56

(i) Clean the work area for bonding with:

Textile - Lint free Cotton 14SBA1

and

Non Aqueous Cleaner - 08BAA9

General
(j) Bond the Service Bulletin placard identified as SB27–3237, item 74, refer to Ref.
Fig. Modification of the CB-Box 5000VE, view D, supplied in:

1 PLACARD SET F9237000703600

(k) Install the APU starter box, refer to Ref. AMM Task 31-18-51-400-801.

REV 00 Oct 12/20 A330-27-3237

Page 184
 A330
SERVICE BULLETIN

CONF 005
FR73

A Z160

FR65

5000VE

5051VCA

E F

B D

(181)

A
5000VE

ICN-A330-A-27XX3237-A-FAPE3-013A3-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013A3-A-001-01 SHEET 1/5

REV 00 Oct 12/20 A330-27-3237
Modification of the CB-Box 5000VE
Page 185
 A330
SERVICE BULLETIN

CONF 005

BEFORE

(32) x4

(33)
(56) x4 B

(57) APU
57 COM
MAIN MODE INTRPT 31.5 mm
ELSD CTL SUPPLY SUPPLY SUPPLY (1.240 in)
135

17 mm
DIA
(0.669 in)

C
26 mm 20 mm ± 0.2 VIEW LOOKING AFT
(1.024 in) (0.787 in ±0.008)
ICN-A330-A-27XX3237-A-FAPE3-013A4-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013A4-A-002-01 SHEET 2/5

REV 00 Oct 12/20 A330-27-3237
Modification of the CB-Box 5000VE
Page 186
 A330
SERVICE BULLETIN

CONF 005

99

AFTER

G
01

01 03

74 SB27-3237
IMPLEMENTED

02

32 x4

33

56 x4
NOTE:
01 PART OF CIRCUIT BREAKER, ITEM 99
D
02 RE-IDENTIFY FRONTPLATE WITH INDELIBLE INK:
OLD PART NUMBER NEW PART NUMBER
F925-90013-006-00 F925-90013-008-00
03 TORQUE VALUE BETWEEN 0.45 m.daN (39.84 lbf.in) AND 0.50 m.daN (44.16 lbf.in)
ICN-A330-A-27XX3237-A-FAPE3-013A5-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013A5-A-003-01 SHEET 3/5

REV 00 Oct 12/20 A330-27-3237
Modification of the CB-Box 5000VE
Page 187
 A330
SERVICE BULLETIN

CONF 005

BEFORE 1KD

2KD

(132)

01

01
01
AFTER

5051VC

136 05

133 59CS
E
59CS
2KD 99
134
1KD 01

01

01 04

01 04
01

NOTE:
01 PART OF CIRCUIT BREAKER,
ITEM 99
04 TORQUE VALUE BETWEEN
MIN 0.17 m.daN (15.0 lbf.in) AND
MAX 0.18 m.daN (15.9 lbf.in) F
05 ATTACH TO EXISTING
ELECTRICAL HARNESS
WITH CABLE TIES,
ITEM 61, AS NECESSARY
ICN-A330-A-27XX3237-A-FAPE3-013A6-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013A6-A-001-01 SHEET 4/5

REV 00 Oct 12/20 A330-27-3237
Modification of the CB-Box 5000VE
Page 188
 A330
SERVICE BULLETIN

CONF 005

EL
SD
CT
L
99
59CS

62

63
G

ICN-A330-A-27XX3237-A-FAPE3-013A7-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013A7-A-001-01 SHEET 5/5

REV 00 Oct 12/20 A330-27-3237
Modification of the CB-Box 5000VE
Page 189
 A330
SERVICE BULLETIN

CONF 005

BEFORE

5 10
2 1 2 1
3 3

5 5

2KD 1KD
CTL MAIN
SUPPLY
5051VC-A -A

5051VC
AFTER

6146-DR18
01

1MF
3 5 10
2 1 2 1 2 1
3 3

59CS
ELSD 5 5

2KD 1KD
NEW WIRE, NEW SHUNT
CTL MAIN
DELETED SHUNT SUPPLY

NOTE:
NOTE:
UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA No 3118
01 NEW SHUNT IS NECESSARY : SEE MODIFICATION OF CB-BOX 5000VE
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE IN 5000VE
ICN-A330-A-27XX3237-A-FAPE3-013AC-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013AC-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Modification of the Wiring in CB-Box 5000VE
Page 190
 A330
SERVICE BULLETIN

CONF 005

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
ZONE OR ELEC. WIRE ZONE OR ELEC.
E TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 162 59CS ELSD 2 NSA936501TA1603 3118- 6146 1MF DR18 1000 40 162 5051VC -A EN3155-019F2018 A <1>

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
<1> Frigther ELT.EQUIPMENT G9297006500200 "SHEET 08,ISSUE C"
D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C2-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in CB-Box 5000VE
Page 191
 A330
SERVICE BULLETIN

CONF 001
(9) Task A330-A-27-XX-3237-04001-920A-A (A330-A-27-XX-3237-04ZZZ-920Z-A)
Modify the Electrical Harness 5869VB
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 6.00 h
Minimum Number of person 1
Elapsed Time 6.00 h
Skills Airframe
Material necessary to do the job
Part kit 273237D09R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
29 NSA935401-00 1 TIE
F9297001300600 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
AWM 27-98-08
20-33-00
20-33-44
ESPM
20-43-12
20-56-51
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
(b) Modify the electrical harness, refer to Ref. Fig. Removal of the Electrical Harness
5869VB.
1 Remove and reuse all installed labels, item (141), item (142), item (143),
item (144) and item (145), as shown on SHEET 01.
2 Disconnect the wires from the connectors 1CSB, 1CSG and 1CSJ, as shown
on view A.
3 Remove, as shown on view A:

1 GROMMET Item (79) Discard

REV 00 Oct 12/20 A330-27-3237

Page 192
 A330
SERVICE BULLETIN

1 LIGHTN.PRO.SYS. Item (80) Discard

1 LIGHTN.PRO.SYS. Item (155) Retain

1 FITTING-CONDUIT Item (156) Retain

1 LIGHTN.PRO.SYS. Item (157) Retain

1 FITTING-CONDUIT Item (158) Retain

1 LIGHTN.PRO.SYS. Item (159) Retain

1 LIGHTN.PRO.SYS. Item (160) Retain

1 CABLE TIE Item (29) Discard

NOTE: Remove lock wire, if necessary.

4 Remove, as shown on view B and Ref. ESPM 20-43-12:

3 POLYOLEFINE SLEEVES Item (75) Discard

H

1 SLEEVE,SHRINKABLE Item (76) Discard

4 POLYOLEFINE SLEEVES Item (77) Discard

H

2 POLYOLEFINE SLEEVES Item (78) Discard

H
(c) Modify the wiring.
Refer to Ref. ESPM 20-33-00
1 Remove the wire(s) as shown on this(these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Electrical Harness 5869VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5869VB
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Electrical Harness 5869VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5869VB
Ref. AWM 27-98-08.
(d) Put the heat shrink sleeve over the wires that go into the cross-junction, item
75, item 77, item 78 and item 81, refer to Ref. Fig. Installation of the Electrical
Harness 5869VB, SHEET 01 and Ref. ESPM 20-43-12, supplied in:

1 ELECTRICAL F9297001300600
EQUIPMENT
(e) Install the sleeve identified as 2798–5041, item 82, refer to Ref. Fig. Installation
of the Electrical Harness 5869VB, SHEET 01, supplied in:

1 ELECTRICAL F9297001300600
EQUIPMENT

REV 00 Oct 12/20 A330-27-3237

Page 193
 A330
SERVICE BULLETIN

(f) Install the sleeve identified as 6326VN25/DC1, 6327VN25/B1, item 95, refer to
Ref. Fig. Installation of the Electrical Harness 5869VB, SHEET 01, supplied in:

1 ELECTRICAL F9297001300600
EQUIPMENT
(g) Install the retained fitting conduit and lightning protection system, refer to Ref.
Fig. Installation of the Electrical Harness 5869VB, view A.

1 LIGHTN.PRO.SYS. Item (155) Retained

1 FITTING-CONDUIT Item (156) Retained

1 LIGHTN.PRO.SYS. Item (157) Retained

1 FITTING-CONDUIT Item (158) Retained

1 LIGHTN.PRO.SYS. Item (159) Retained

1 LIGHTN.PRO.SYS. Item (160) Retained

1 TIE-CABLE NSA935401-00 Item 29

(h) Install the new fitting conduit and lightning protection system, item 79, item 83,
item 84, item 85, item 86, item 87, item 88, item 150, item 151 and item 152,
refer to Ref. Fig. Installation of the Electrical Harness 5869VB, view A and view B,
supplied in:

1 ELECTRICAL F9297001300600
EQUIPMENT
(i) Connect the wires to the connectors 1CSB, 1CSG, 1CSJ and 58CSS, refer to Ref.
Fig. Installation of the Electrical Harness 5869VB, view A.
(j) Install the new labels identified as 58CS S, item 89, and SB27–3237, item 74,
refer to Ref. Fig. Installation of the Electrical Harness 5869VB, view C, supplied
in:

1 ELECTRICAL F9297001300600
EQUIPMENT

REV 00 Oct 12/20 A330-27-3237

Page 194
 A330
SERVICE BULLETIN

CONF 001

TO
5202VC
5203VC (142) 01
5219VC
1MFC
(141) 01
(142) 01 (143) 01 (142) 01 (144) 01
5869VB/FBW
1MFC 1CS J 1MFC 1CS B
(141) 01
1CSG
5869VB 5869VB/FBW
1CSB

(141) 01

5869VB/FBW 1CSJ
(145) 01
(142) 01 (141) 01
1CS G
01 (141)
1MFC 5869VB/FBW

5869VB/FBW
01 (142)

1MFC
(141) 01

5869VB/FBW

(141) 01

5869VB/FBW
5287VN /DC1 01 (142)

1MFC
(142) 01

TO FR80 1MFC
A

NOTE:
01 REMOVE AND REUSE ALL INSTALLED LABELS IN THIS AREA.
THE SHOWN QUANTITY AND POSITION OF THE LABELS CAN DEVIATE FROM REALITY.
ALL CABLE TIES, ITEM 29, THAT FIXED THESE LABELS WILL BE DISCARDED
ICN-A330-A-27XX3237-A-FAPE3-0139E-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139E-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5869VB
Page 195
 A330
SERVICE BULLETIN

CONF 001

TO
5202VC
5203VC
5219VC

B
1CSG

(157)
(155)
1CSB

(159)

1CSJ
5869VB (156)

(160)

(80)
(158)

(79)

02

(29) 5287VN /DC1

(80)

TO FR80
NOTE: A
02 REMOVE LOCKWIRE IF NECESSARY
ICN-A330-A-27XX3237-A-FAPE3-0139F-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139F-A-001-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5869VB
Page 196
 A330
SERVICE BULLETIN

CONF 001

TO
5202VC
5203VC
5219VC

1CSG

(75)
(77)

1CSB

(77) WIRE
2798-5041 (B) 03
1CSJ (77)
(75) (78)
WIRE
2798-5041 (R) 03
5869VB

(77) (78)

(75)
(76)

5287VN

WIRE
2798-5041 (B) 03

WIRE
2798-5041 (R) 03

TO FR80 B
NOTE:
03 REMOVE WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139G-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139G-A-001-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5869VB
Page 197
 A330
SERVICE BULLETIN

CONF 001

BEFORE
1MF
5869VB
B 1
2798-5041-PN24
R 2

1
E G 1CS

2
E

4
D

5213VT

AFTER
1MF
5869VB
B 1
2798-5041-DRB24
R 2

1
E G 1CS

2
E 1MF

4 6326VN25 /DC1 2798-5045-DR18 2

D 2798-5046-DR18 1
6327VN25 /B1 2798-5047-DR18 3
5213VT

S 58CS

NOTE:
ONLY WIRES RELATED TO THIS NEW WIRE
SERVICE BULLETIN ARE SHOWN DELETED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5869VB
Page 198
 A330
SERVICE BULLETIN

CONF 001

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 21650 852,4 311 - - - BEFORE (5871VB)

5 150 5112VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 20000 787,4 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF PN24 3480 137,0 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF PN24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 006 00 "SHEET 33,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-0135K-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 199
 A330
SERVICE BULLETIN

CONF 001

58CSS

TO NEW WIRES
5202VC 2798-5045
5203VC 2798-5046
5219VC 2798-5047

1CSG
78

75
A
77

1CSB

82
2798-5041
1CSJ 77 78
77
75

NEW WIRE
2798-5041 (B)
5869VB
NEW WIRE
2798-5041 (R)
95
6326VN25 /DC1
77 78
95
6327VN25 /B1
78
NEW WIRE NEW WIRE
2798-5047 2798-5045

81 75

77
5287VN /DC1

6327VN25 /B1 5287VN /DC1

6326VN25 /DC1 78
NEW WIRE
2798-5046
NEW WIRE
2798-5041 (B)
NEW WIRE
TO FR80 2798-5041 (R)
TO 5213VT
ICN-A330-A-27XX3237-A-FAPE3-01367-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01367-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5869VB
Page 200
 A330
SERVICE BULLETIN

CONF 001

TO 58CSS
5202VC
5203VC
5219VC

84
1CSG

C
(155)

1CSB

(157)
(159)
(157)
5869VB
B

85
(160)
(156)
1CSJ

86 (158)
01

79 81 151 150 85
152 151
86 84
29 78

BUNDLE
88

TO 5213VT

83
NOTE: 87
FOR CONNECTION OF THE CABLES REFER TO
MODIFICATION OF THE WIRING IN THE
ELECTRICAL HARNESS 5869VB AND AWM 27-98-08
01 SECURE WITH LOCKWIRE IF NECESSARY A B
ICN-A330-A-27XX3237-A-FAPE3-01368-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01368-A-001-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5869VB
Page 201
 A330
SERVICE BULLETIN

CONF 001
(142) 02 (141) 02 (143) 02
58CSS
1MFC 5869VB/FBW 1CS J
TO
5202VC
5203VC (142) 02
5219VC 89
1MFC
(141) 02 58CS S
(142) 02
5869VB/FBW
1MFC
1CSJ
1CSG
5869VB 74
(144) 02
SB27-3237
1CS B

1CSB

(141) 02

5869VB/FBW (145) 02

1MFC 1CS G

(142) 02
5869VB/FBW
5869VB/FBW
(141) 02
(141) 02 1MFC

(142) 02
5869VB/FBW

(141) 02
5287VN /DC1 (141) 02

6327VN25 /B1 5287VN /DC1 5869VB/FBW

6326VN25 /DC1
1MFC
(142) 02
(142) 02
TO FR80 1MFC

NOTE:
02 REUSE ALL REMOVED LABELS IN THIS AREA.
C
INSTALL THE REMOVED LABELS AT THE SAME POSITION AS BEFORE THE MODIFICATION.
FIX ALL LABELS WITH CABLE TIES, ITEM 29
ICN-A330-A-27XX3237-A-FAPE3-01369-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01369-A-001-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5869VB
Page 202
 A330
SERVICE BULLETIN

CONF 002-004
(9) Task A330-A-27-XX-3237-04002-920A-A (A330-A-27-XX-3237-04ZZZ-920Z-A)
Modify the Electrical Harness 5869VB
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 6.00 h
Minimum Number of person 1
Elapsed Time 6.00 h
Skills Airframe
Material necessary to do the job
Part kit 273237D02R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
29 NSA935401-00 1 TIE
F9297001300700 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
AWM 27-98-08
20-33-00
20-33-44
ESPM
20-43-12
20-56-51
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
(b) Modify the electrical harness, refer to Ref. Fig. Removal of the Electrical Harness
5869VB.
1 Remove and reuse all installed labels, item (141), item (142), item (143),
item (144) and item (145), as shown on SHEET 01.
2 Disconnect the wires from the connectors 1CSB, 1CSG and 1CSJ, as shown
on view A.
3 Remove, as shown on view A:

1 LIGHTN.PRO.SYS. Item (148) Retain

REV 00 Oct 12/20 A330-27-3237

Page 203
 A330
SERVICE BULLETIN

1 LIGHTN.PRO.SYS. Item (146) Retain

1 LIGHTN.PRO.SYS. Item (147) Retain

1 LIGHTN.PRO.SYS. Item (93) Discard

1 LIGHTN.PRO.SYS. Item (91) Discard

1 TRANSITION Item (92) Discard

1 LIGHTN.PRO.SYS. Item (90) Discard

1 GROMMET Item (79) Discard

1 CABLE TIE Item (29) Discard

NOTE: Remove lock wire, if necessary

4 Remove, as shown on view B and Ref. ESPM 20-43-12:

5 POLYOLEFINE SLEEVES Item (75) Discard

H

4 POLYOLEFINE SLEEVES Item (77) Discard

H

1 POLYOLEFINE SLEEVES Item (78) Discard

H

1 SLEEVE,SHRINKABLE Item (94) Discard

(c) Modify the wiring.
Refer to Ref. ESPM 20-33-00
1 Remove the wire(s) as shown on this(these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Electrical Harness 5869VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5869VB
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Electrical Harness 5869VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5869VB
Ref. AWM 27-98-08.
(d) Put the heat shrink sleeve over the wires that go into the cross-junction, item
75, item 77, item 78 and item 81, refer to Ref. Fig. Installation of the Electrical
Harness 5869VB, SHEET 01 and Ref. ESPM 20-43-12, supplied in:

1 ELECTRICAL F9297001300700
EQUIPMENT
(e) Install the sleeve identified as 2798–5041, item 82, refer to Ref. Fig. Installation
of the Electrical Harness 5869VB, SHEET 01, supplied in:

1 ELECTRICAL F9297001300700
EQUIPMENT

REV 00 Oct 12/20 A330-27-3237

Page 204
 A330
SERVICE BULLETIN

(f) Install the sleeve identified as 6326VN25/DC1, 6327VN25/B1, item 95, refer to
Ref. Fig. Installation of the Electrical Harness 5869VB, SHEET 01, supplied in:

1 ELECTRICAL F9297001300700
EQUIPMENT
(g) Install the retained fitting conduit and lightning protection system, refer to Ref.
Fig. Installation of the Electrical Harness 5869VB, view A.

1 LIGHTN.PRO.SYS. Item (148) Retained

1 LIGHTN.PRO.SYS. Item (146) Retained

1 LIGHTN.PRO.SYS. Item (147) Retained

1 TIE-CABLE NSA935401-00 Item 29

(h) Install the new fitting conduit and lightning protection system, item 79, item 83,
item 84, item 85, item 86, item 87, item 88, item 96, item 97, item 98, item 150,
item 151 and item 152, refer to Ref. Fig. Installation of the Electrical Harness
5869VB, view A and view B, supplied in:

1 ELECTRICAL F9297001300700
EQUIPMENT
(i) Connect the wires to the connectors 1CSB, 1CSG, 1CSJ and 58CSS, refer to Ref.
Fig. Installation of the Electrical Harness 5869VB, view A.
(j) Install the new labels identified as 58CS S, item 89 and SB27–3237, item 74,
refer to Ref. Fig. Installation of the Electrical Harness 5869VB, view C, supplied
in:

1 ELECTRICAL F9297001300700
EQUIPMENT

REV 00 Oct 12/20 A330-27-3237

Page 205
 A330
SERVICE BULLETIN

CONF 002-004

TO
5202VC
5203VC
5219VC

(141) 01 (142) 01 (143) 01 (142) 01 (144) 01

5869VB/FBW 1MFC 1CS J 1MFC 1CS B

(141) 01
1CSG
(142) 01 5869VB/FBW
1CSB
1MFC
5869VB/FBW

(141) 01

1CSJ
(145) 01
(142) 01 (141) 01
1CS G
1MFC 5869VB/FBW
5869VB
5869VB/FBW

(141) 01
1MFC
(141) 01
(142) 01
5869VB/FBW

(141) 01

5869VB/FBW
5287VN /DC1

1MFC
TO FR80
(142) 01
(142) 01
1MFC
A

NOTE:
01 REMOVE AND REUSE ALL INSTALLED LABELS IN THIS AREA.
THE SHOWN QUANTITY AND POSITION OF THE LABELS CAN DEVIATE FROM REALITY.
ALL CABLE TIES, ITEM 29, THAT FIXED THESE LABELS WILL BE DISCARDED
ICN-A330-A-27XX3237-A-FAPE3-01364-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01364-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5869VB
Page 206
 A330
SERVICE BULLETIN

CONF 002-004

TO
5202VC
5203VC
5219VC

1CSG

5869VB

1CSB
B
(147)
(91)

(90)

(148)

1CSJ
02
(92)
(93)
(146)
(29)

(79)
TO FR80

(93)

5287VN /DC1
NOTE: A
02 REMOVE LOCKWIRE IF NECESSARY
ICN-A330-A-27XX3237-A-FAPE3-01365-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01365-A-001-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5869VB
Page 207
 A330
SERVICE BULLETIN

CONF 002-004

TO
5202VC
5203VC
5219VC

1CSG

(78)

1CSB
(77)
WIRE
2798-5041 (B) 03
(75)
(75)
WIRE
2798-5041 (R) 03
5869VB
(77)
(75)
1CSJ

(75)
(77)

(94)

5287VN (77)

(75)

WIRE
2798-5041 (B) 03
WIRE
2798-5041 (R) 03

TO FR80 B
NOTE:
03 REMOVE WIRE
ICN-A330-A-27XX3237-A-FAPE3-01366-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01366-A-001-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5869VB
Page 208
 A330
SERVICE BULLETIN

CONF 002-004

BEFORE
1MF
5869VB
B 1
2798-5041-PN24
R 2

1
E G 1CS

2
E

4
D

5213VT

AFTER
1MF
5869VB
B 1
2798-5041-DRB24
R 2

1
E G 1CS

2
E 1MF

4 6326VN25 /DC1 2798-5045-DR18 2

D 2798-5046-DR18 1
6327VN25 /B1 2798-5047-DR18 3
5213VT

S 58CS

NOTE:
ONLY WIRES RELATED TO THIS NEW WIRE
SERVICE BULLETIN ARE SHOWN DELETED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5869VB
Page 209
 A330
SERVICE BULLETIN

CONF 002-004

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 21650 852,4 311 - - - BEFORE (5871VB)

5 150 5112VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 20000 787,4 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF PF24 3340 131,5 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF PF24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 007 00 "SHEET 34,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C3-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 210
 A330
SERVICE BULLETIN

CONF 002-004

TO
5202VC 58CSS
5203VC
5219VC

NEW WIRES
2798-5045
2798-5046
2798-5047

1CSG
78
75

A 75
77

1CSB

82
2798-5041
5869VB 1CSJ 77 78
77

NEW WIRE
2798-5041 (B)
NEW WIRE
2798-5041 (R)
95
81 6326VN25 /DC1
77 78
95
6327VN25 /B1
78
NEW WIRE NEW WIRE
2798-5047 2798-5045
75

77
5287VN /DC1

6327VN25 /B1 5287VN /DC1

6326VN25 /DC1 78
NEW WIRE
2798-5046
NEW WIRE
2798-5041 (B)
NEW WIRE
TO FR80 2798-5041 (R)
TO 5213VT
ICN-A330-A-27XX3237-A-FAPE3-0137T-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137T-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5869VB
Page 211
 A330
SERVICE BULLETIN

CONF 002-004

58CSS
TO
5202VC
5203VC
5219VC

84
1CSG

C
97

1CSB

98
(147)
98
B
5869VB
85
(148)
96
1CSJ

01

86 (146)
29

79 81 151 150 85
152 151
86 84
78

BUNDLE
TO 5213VT 88

83

NOTE: 87
FOR CONNECTION OF THE CABLES REFER TO
MODIFICATION OF THE WIRING IN THE ELECTRICAL
HARNESS 5869VB AND AWM 27-98-08
01 SECURE WITH LOCKWIRE IF NECESSARY A B
ICN-A330-A-27XX3237-A-FAPE3-0137U-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137U-A-001-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5869VB
Page 212
 A330
SERVICE BULLETIN

CONF 002-004
(142) 02 (141) 02 (143) 02
58CSS
1MFC 5869VB/FBW 1CS J
TO
5202VC
5203VC
5219VC 89

58CS S
(142) 02
(141) 02

1MFC
5869VB/FBW
1CSJ
74 1CSG
(142) 02 (144) 02

SB27-3237 1CS B
1MFC
(141) 02

5869VB/FBW 1CSB

(145) 02

1MFC 1CS G

5869VB (142) 02
5869VB/FBW
5869VB/FBW
(141) 02
1MFC
(141) 02
(142) 02
5869VB/FBW

(141) 02
5287VN /DC1 (141) 02

6327VN25 /B1 5287VN /DC1 5869VB/FBW

6326VN25 /DC1
1MFC
TO FR80 (142) 02
(142) 02
1MFC

NOTE:
02 REUSE ALL REMOVED LABELS IN THIS AREA.
C
INSTALL THE REMOVED LABELS AT THE SAME POSITION AS BEFORE THE MODIFICATION.
FIX ALL LABELS WITH CABLE TIES, ITEM 29
ICN-A330-A-27XX3237-A-FAPE3-0137V-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137V-A-001-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5869VB
Page 213
 A330
SERVICE BULLETIN

CONF 005
(9) Task A330-A-27-XX-3237-04012-920A-A (A330-A-27-XX-3237-04ZZZ-920Z-A)
Modify the Electrical Harness 5869VB
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 6.00 h
Minimum Number of person 1
Elapsed Time 6.00 h
Skills Airframe
Material necessary to do the job
Part kit 273237D07R03
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
29 NSA935401-00 1 TIE
F9297001300800 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
AWM 27-98-08
20-33-00
20-33-44
ESPM
20-43-12
20-56-51
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
(b) Modify the electrical harness, Ref. Fig. Removal of the Electrical Harness 5869VB.
1 Remove and reuse all installed labels, item (141), item (142), item (143),
item (144) and item (145), as shown on SHEET 01.
2 Disconnect the wires from the connectors 1CSB, 1CSG and 1CSJ, as shown
on view A.
3 Remove, as shown on view A:

1 GROMMET Item (79) Discard

1 LIGHTN.PRO.SYS. Item (80) Discard

REV 00 Oct 12/20 A330-27-3237
Page 214
 A330
SERVICE BULLETIN

1 LIGHTN.PRO.SYS. Item (155) Retain

1 FITTING-CONDUIT Item (156) Retain

1 LIGHTN.PRO.SYS. Item (157) Retain

1 FITTING-CONDUIT Item (158) Retain

1 LIGHTN.PRO.SYS. Item (159) Retain

1 LIGHTN.PRO.SYS. Item (160) Retain

1 GROMMET Item (79) Discard

1 CABLE TIE Item (29) Discard

NOTE: Remove lock wire, if necessary.

4 Remove, as shown on view B and Ref. ESPM 20-43-12:

3 POLYOLEFINE SLEEVES Item (75) Discard

H

1 SLEEVE,SHRINKABLE Item (76) Discard

4 POLYOLEFINE SLEEVES Item (77) Discard

H

2 POLYOLEFINE SLEEVES Item (78) Discard

H
(c) Modify the wiring.
Refer to Ref. ESPM 20-33-00
1 Remove the wire(s) as shown on this(these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Electrical Harness 5869VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5869VB
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Electrical Harness 5869VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5869VB
Ref. AWM 27-98-08.
(d) Put the heat shrink sleeve over the wires that go into the cross-junction, item
75, item 77, item 78 and item 81, refer to Ref. Fig. Installation of the Electrical
Harness 5869VB, SHEET 01 and Ref. ESPM 20-43-12, supplied in:

1 ELECTRICAL F9297001300800
EQUIPMENT
(e) Install the sleeve identified as 2798–5041, item 82, refer to Ref. Fig. Installation
of the Electrical Harness 5869VB, SHEET 01, supplied in:

1 ELECTRICAL F9297001300800
EQUIPMENT

REV 00 Oct 12/20 A330-27-3237

Page 215
 A330
SERVICE BULLETIN

(f) Install the sleeve identified as 6326VN25/DC1, 6327VN25/B1, item 95, refer to
Ref. Fig. Installation of the Electrical Harness 5869VB, SHEET 01, supplied in:

1 ELECTRICAL F9297001300800
EQUIPMENT
(g) Install the retained fitting conduit and lightning protection system, refer to Ref.
Fig. Installation of the Electrical Harness 5869VB, view A.

1 LIGHTN.PRO.SYS. Item (155) Retained

1 FITTING-CONDUIT Item (156) Retained

1 LIGHTN.PRO.SYS. Item (157) Retained

1 FITTING-CONDUIT Item (158) Retained

1 LIGHTN.PRO.SYS. Item (159) Retained

1 LIGHTN.PRO.SYS. Item (160) Retained

1 TIE-CABLE NSA935401-00 Item 29

(h) Install the new fitting conduit and lightning protection system, item 79, item 83,
item 84, item 85, item 86, item 87, item 88, item 150, item 151 and item 152,
refer to Ref. Fig. Installation of the Electrical Harness 5869VB, view A and view B,
supplied in:

1 ELECTRICAL F9297001300800
EQUIPMENT
(i) Connect the wires to the connectors 1CSB, 1CSG, 1CSJ and 58CSS, refer to Ref.
Fig. Installation of the Electrical Harness 5869VB, view A.
(j) Install the new labels identified as 58CS S, item 89, and SB27–3237, item 74,
refer to Ref. Fig. Installation of the Electrical Harness 5869VB, view C, supplied
in:

1 ELECTRICAL F9297001300800
EQUIPMENT

REV 00 Oct 12/20 A330-27-3237

Page 216
 A330
SERVICE BULLETIN

CONF 005

TO
5202VC
5203VC (142) 01
5219VC
1MFC
(141) 01
(142) 01 (143) 01 (142) 01 (144) 01
5869VB/FBW
1MFC 1CS J 1MFC 1CS B
(141) 01
1CSG
5869VB 5869VB/FBW
1CSB

(141) 01

5869VB/FBW 1CSJ
(145) 01
(142) 01 (141) 01
1CS G
01 (141)
1MFC 5869VB/FBW

5869VB/FBW
01 (142)

1MFC
(141) 01

5869VB/FBW

(141) 01

5869VB/FBW
5287VN /DC1 01 (142)

1MFC
(142) 01

TO FR80 1MFC
A

NOTE:
01 REMOVE AND REUSE ALL INSTALLED LABELS IN THIS AREA.
THE SHOWN QUANTITY AND POSITION OF THE LABELS CAN DEVIATE FROM REALITY.
ALL CABLE TIES, ITEM 29, THAT FIXED THESE LABELS WILL BE DISCARDED
ICN-A330-A-27XX3237-A-FAPE3-0139E-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139E-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5869VB
Page 217
 A330
SERVICE BULLETIN

CONF 005

TO
5202VC
5203VC
5219VC

B
1CSG

(157)
(155)
1CSB

(159)

1CSJ
5869VB (156)

(160)

(80)
(158)

(79)

02

(29) 5287VN /DC1

(80)

TO FR80
NOTE: A
02 REMOVE LOCKWIRE IF NECESSARY
ICN-A330-A-27XX3237-A-FAPE3-0139F-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139F-A-001-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5869VB
Page 218
 A330
SERVICE BULLETIN

CONF 005

TO
5202VC
5203VC
5219VC

1CSG

(75)
(77)

1CSB

(77) WIRE
2798-5041 (B) 03
1CSJ (77)
(75) (78)
WIRE
2798-5041 (R) 03
5869VB

(77) (78)

(75)
(76)

5287VN

WIRE
2798-5041 (B) 03

WIRE
2798-5041 (R) 03

TO FR80 B
NOTE:
03 REMOVE WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139G-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139G-A-001-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5869VB
Page 219
 A330
SERVICE BULLETIN

CONF 005

BEFORE
1MF
5869VB
B 1
2798-5041-PN24
R 2

1
E G 1CS

2
E

4
D

5213VT

AFTER
1MF
5869VB
B 1
2798-5041-DRB24
R 2

1
E G 1CS

2
E 1MF

4 6326VN25 /DC1 2798-5045-DR18 2

D 2798-5046-DR18 1
6327VN25 /B1 2798-5047-DR18 3
5213VT

S 58CS

NOTE:
ONLY WIRES RELATED TO THIS NEW WIRE
SERVICE BULLETIN ARE SHOWN DELETED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5869VB
Page 220
 A330
SERVICE BULLETIN

CONF 005

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 19400 763,8 311 - - - BEFORE (5871VB)

5 150 5051VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 19400 763,8 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 3440 135,4 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 008 00 "SHEET 35,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C4-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 221
 A330
SERVICE BULLETIN

CONF 005

58CSS

TO NEW WIRES
5202VC 2798-5045
5203VC 2798-5046
5219VC 2798-5047

1CSG
78

75
A
77

1CSB

82
2798-5041
1CSJ 77 78
77
75

NEW WIRE
2798-5041 (B)
5869VB
NEW WIRE
2798-5041 (R)
95
6326VN25 /DC1
77 78
95
6327VN25 /B1
78
NEW WIRE NEW WIRE
2798-5047 2798-5045

81 75

77
5287VN /DC1

6327VN25 /B1 5287VN /DC1

6326VN25 /DC1 78
NEW WIRE
2798-5046
NEW WIRE
2798-5041 (B)
NEW WIRE
TO FR80 2798-5041 (R)
TO 5213VT
ICN-A330-A-27XX3237-A-FAPE3-01367-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01367-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5869VB
Page 222
 A330
SERVICE BULLETIN

CONF 005

TO 58CSS
5202VC
5203VC
5219VC

84
1CSG

C
(155)

1CSB

(157)
(159)
(157)
5869VB
B

85
(160)
(156)
1CSJ

86 (158)
01

79 81 151 150 85
152 151
86 84
29 78

BUNDLE
88

TO 5213VT

83
NOTE: 87
FOR CONNECTION OF THE CABLES REFER TO
MODIFICATION OF THE WIRING IN THE
ELECTRICAL HARNESS 5869VB AND AWM 27-98-08
01 SECURE WITH LOCKWIRE IF NECESSARY A B
ICN-A330-A-27XX3237-A-FAPE3-01368-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01368-A-001-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5869VB
Page 223
 A330
SERVICE BULLETIN

CONF 005
(142) 02 (141) 02 (143) 02
58CSS
1MFC 5869VB/FBW 1CS J
TO
5202VC
5203VC (142) 02
5219VC 89
1MFC
(141) 02 58CS S
(142) 02
5869VB/FBW
1MFC
1CSJ
1CSG
5869VB 74
(144) 02
SB27-3237
1CS B

1CSB

(141) 02

5869VB/FBW (145) 02

1MFC 1CS G

(142) 02
5869VB/FBW
5869VB/FBW
(141) 02
(141) 02 1MFC

(142) 02
5869VB/FBW

(141) 02
5287VN /DC1 (141) 02

6327VN25 /B1 5287VN /DC1 5869VB/FBW

6326VN25 /DC1
1MFC
(142) 02
(142) 02
TO FR80 1MFC

NOTE:
02 REUSE ALL REMOVED LABELS IN THIS AREA.
C
INSTALL THE REMOVED LABELS AT THE SAME POSITION AS BEFORE THE MODIFICATION.
FIX ALL LABELS WITH CABLE TIES, ITEM 29
ICN-A330-A-27XX3237-A-FAPE3-01369-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01369-A-001-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5869VB
Page 224
 A330
SERVICE BULLETIN

CONF 001 005

(10) Task A330-A-27-XX-3237-05001-920A-A (A330-A-27-XX-3237-05ZZZ-920Z-A)
Modify the Electrical Harness 5870VB
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 9.00 h
Minimum Number of person 1
Elapsed Time 9.00 h
Skills Electrical
Material necessary to do the job
Part kit 273237D01R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
29 NSA935401-00 1 TIE
F9297001400400 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
AWM 27-98-08
20-33-00
20-33-44
ESPM
20-43-12
20-56-51
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
(b) Modify the electrical harness, refer to Ref. Fig. Removal of the Electrical Harness
5870VB.
1 Remove and reuse all installed labels item (161), item (162), item (163),
item (164) and item (165), as shown on SHEET 01.
2 Disconnect the wires from the connectors 1CSD, 1CSH and 1CSK, as shown
on view A.
3 Remove, as shown on view A:

1 LIGHTN.PRO.SYS. Item (171) Retain

REV 00 Oct 12/20 A330-27-3237

Page 225
 A330
SERVICE BULLETIN

1 TRANSITION Item (172) Retain

1 LIGHTN.PRO.SYS. Item (173) Retain

1 LIGHTN.PRO.SYS. Item (174) Retain

1 LIGHTN.PRO.SYS. Item (175) Retain

1 TRANSITION Item (176) Retain

1 LIGHTN.PRO.SYS. Item (100) Discard

1 CABLE TIE Item (29) Discard

NOTE: Remove lock wire, if necessary.

4 Remove, as shown on view B and Ref. ESPM 20-43-12:

7 POLYOLEFINE SLEEVES Item (75) Discard

H

1 SLEEVE,SHRINKABLE Item (101) Discard

1 SLEEVE,SHRINKABLE Item (94) Discard

1 SLEEVE,SHRINKABLE Item (76) Discard

(c) Modify the wiring
Refer to Ref. ESPM 20-33-00
1 Remove the wire(s) as shown on this(these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Electrical Harness 5870VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5870VB
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Electrical Harness 5870VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5870VB
Ref. AWM 27-98-08.
(d) Put the heat shrink sleeve over the wires that go into the cross-junction, item
75, item 78, item 81, item 94 and item 101, refer to Ref. Fig. Installation of the
Electrical Harness 5870VB, SHEET 01 and Ref. ESPM 20-43-12, supplied in:

1 ELECTRICAL F9297001400400
EQUIPMENT
(e) Install the retained fitting conduit and lightning protection system, refer to Ref.
Fig. Installation of the Electrical Harness 5870VB, view A.

1 LIGHTN.PRO.SYS. Item (171) Retained

1 TRANSITION Item (172) Retained

1 LIGHTN.PRO.SYS. Item (173) Retained

1 LIGHTN.PRO.SYS. Item (174) Retained

1 LIGHTN.PRO.SYS. Item (175) Retained

REV 00 Oct 12/20 A330-27-3237

Page 226
 A330
SERVICE BULLETIN

1 TRANSITION Item (176) Retained

1 TIE-CABLE NSA935401-00 Item 29

(f) Install the new fitting conduit and lightning protection system, item 84, item 85,
item 102, item 103, item 104, item 105, item 106, item 150, item 151 and item
152, refer to Ref. Fig. Installation of the Electrical Harness 5870VB, view A and
view B, supplied in:

1 ELECTRICAL F9297001400400
EQUIPMENT
(g) Connect the wires to the connectors 1CSD, 1CSH, 1CSK and 58CSR, refer to Ref.
Fig. Installation of the Electrical Harness 5870VB, view A.
(h) Install the new labels identified as 58CSR, item 89, and SB27–3237, item 74,
refer to Ref. Fig. Installation of the Electrical Harness 5870VB, view C, supplied
in:

1 ELECTRICAL F9297001400400
EQUIPMENT

REV 00 Oct 12/20 A330-27-3237

Page 227
 A330
SERVICE BULLETIN

CONF 001 005

TO
5202VC
5203VC
5219VC
5870VB
(161) 01

5870VB/FBW

5374VN /DC2
(162) 01
5393VN /B2
1CSK 2MFK
(161) 01 (164) 01
(161) 01
5870VB/FBW 1CS D
5870VB/FBW

TO FR80
(163) 01
(162) 01 1CSD
1CS K (162) 01
(162) 01
2MFK
2MFK
2MFK
(161) 01

5870VB/FBW

(162) 01

2MFK

(162) 01

2MFK
(161) 01

A 5870VB/FBW 1CSH 5870VB/FBW

(161) 01 (161) 01

5870VB/FBW
NOTE:
(162) 01 (165) 01 01 REMOVE AND REUSE ALL INSTALLED LABELS IN THIS AREA
THE SHOWN QUANTITY AND POSITION OF THE LABELS CAN DEVIATE FROM REALITY
2MFK 1CS H ALL CABLE TIES, ITEM 29, THAT FIXED THESE LABELS WILL BE DISCARDED

ICN-A330-A-27XX3237-A-FAPE3-0136O-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136O-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5870VB
Page 228
 A330
SERVICE BULLETIN

CONF 001 005

TO
5202VC
5203VC
5219VC

5870VB

5374VN /DC2 02

5393VN /B2

(171)

(182)
B
(29)
1CSK
TO FR80

(172)
1CSD

(100) (175)

(173)
(176)
(174)

1CSH

NOTE:
02 REMOVE LOCKWIRE IF NECESSARY
A
ICN-A330-A-27XX3237-A-FAPE3-0136P-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136P-A-002-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5870VB
Page 229
 A330
SERVICE BULLETIN

CONF 001 005

TO
5202VC
5203VC
5219VC

5870VB

(75)
5374VN /DC2

5393VN /B2 (94)

TO FR80

(75)
1CSK (75) (76)

1CSD

(75)
(75)

(75)

(101)

(75)
1CSH

WIRE
2798-5157 (B) 03
NOTE: WIRE
03 REMOVE WIRE
B 2798-5157 (R) 03
ICN-A330-A-27XX3237-A-FAPE3-0136Q-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136Q-A-001-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5870VB
Page 230
 A330
SERVICE BULLETIN

CONF 001 005

BEFORE
FR56 FR80
2MF
H

7 2798-5157 R 15 V11
8 B 14 V12 RVDT 1 MON
9 2798-5158 R 2798-5159 R 12 V21
10 B B 11 V22

2MF FR91
A 3686VC 5205VP
1CS ACTUATOR THS
5949VC A
5870VB
D
B
C
J

AFTER

2MF 2MF
5212VT 7820VB
R 58CS
6
A R 3
F 2798-6835 5
B
B 4 2798-5048 B
G 1 R
FR56 FR80
2MF
H

7 2798-5157 R 2798-6834 R 15 V11

8 B B 14 V12 RVDT 1 MON
9 2798-5158 R 2798-5159 R 12 V21
10 B B 11 V22

2MF FR91
A 3686VC 5205VP
1CS ACTUATOR THS
5949VC A
5870VB
D
NEW WIRE B
NOTE: C
EXISTING WIRE
ONLY WIRES RELATED TO THIS J
SERVICE BULLETIN ARE SHOWN REROUTED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139O-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139O-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5870VB
Page 231
 A330
SERVICE BULLETIN

CONF 001 005

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 152 3686VC 8 EN3155-014M2018 2798-5157 B 2MF PN24 22980 904,7 310 1CS H 14 EN3155-019F2018 BEFORE

2 152 3686VC 7 EN3155-014M2018 2798-5157 R 2MF PN24 0 0 310 1CS H 15 EN3155-019F2018 BEFORE

3 152 3686VC 8 EN3155-014M2018 2798-5157 B 2MF PN24 22980 904,7 311 5212VT 6G EN3155-016M2018 AFTER

4 152 3686VC 7 EN3155-014M2018 2798-5157 R 2MF PN24 0 0 311 5212VT 6F EN3155-016M2018 AFTER

5 311 5212VT 6B EN3155-016M2018 2798-6835 B 2MF DRB24 5000 196,9 300 58CS R 5 EN3155-019F2018 A

6 311 5212VT 6A EN3155-016M2018 2798-6835 R 2MF DRB24 0 0 300 58CS R 3 EN3155-019F2018 A

7 300 58CS R 4 EN3155-019F2018 2798-6834 B 2MF DRB24 3000 118,1 310 1CS H 14 EN3155-019F2018 A

8 300 58CS R 1 EN3155-019F2018 2798-6834 R 2MF DRB24 0 0 310 1CS H 15 EN3155-019F2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70014 004 00 "SHEET 20,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C0-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5870VB
Page 232
 A330
SERVICE BULLETIN

CONF 001 005

TO
5202VC
5203VC
5219VC

5870VB

5374VN /DC2

5393VN /B2
94 TO FR80
75 TO 5212VT
A
75

75
1CSD 75
81

NEW WIRE 58CSR

2798-6834 (B) NEW WIRE
NEW WIRE 2798-6835 (B)
NEW WIRE 2798-6835 (R)
1CSK 2798-6834 (R)

78

75
75 75
NEW WIRE
2798-6835 (B)

NEW WIRE
2798-6835 (R)

NEW WIRE
2798-6834 (B) 101
75
78 NEW WIRE
2798-6834 (R)

1CSH

75

ICN-A330-A-27XX3237-A-FAPE3-0136F-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136F-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5870VB
Page 233
 A330
SERVICE BULLETIN

CONF 001 005

5870VB

58CSR 5374VN /DC2 01

5393VN /B2

1CSK (171)
C
106

29

TO 5212VT
1CSD
(172)
84
102
85 B
(175)

104
103

81 151
(173) 150 85
152 151
(174)
103 84
78
(176)

1CSH

NOTE:
FOR CONNECTION OF THE CABLES
REFER TO MODIFICATION OF THE BUNDLE
WIRING IN THE ELECTRICAL
HARNESS 5870VB AND
AWM 27-98-08 A B
01 SECURE WITH LOCKWIRE IF NECESSARY 105
ICN-A330-A-27XX3237-A-FAPE3-013EQ-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013EQ-A-001-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5870VB
Page 234
 A330
SERVICE BULLETIN

CONF 001 005

TO
5202VC
5203VC
5219VC
5870VB
5374VN /DC2 (161) 02

5393VN /B2 5870VB/FBW

(161) 02 (164) 02
(162) 02
5870VB/FBW 1CS D
2MFK

1CSK 1CSD
(162) 02
89
TO FR80
58CS R 2MFK
74

SB27-3237 (162) 02
58CSR
(163) 02
2MFK
(161) 02
1CS K
5870VB/FBW
(161) 02
(162) 02
5870VB/FBW

2MFK
(162) 02
(162) 02
2MFK
2MFK
(161) 02

5870VB/FBW 1CSH 5870VB/FBW

(162) 02
(161) 02
2MFK

NOTE:
(161) 02 02 REUSE ALL REMOVED LABELS IN THIS AREA.
INSTALL THE REMOVED LABELS AT THE SAME POSITION
5870VB/FBW 1CS H AS BEFORE THE MODIFICATION.
FIX ALL LABELS WITH CABLE TIES, ITEM 29
C (165) 02
ICN-A330-A-27XX3237-A-FAPE3-013ER-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013ER-A-001-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5870VB
Page 235
 A330
SERVICE BULLETIN

CONF 002-004
(10) Task A330-A-27-XX-3237-05002-920A-A (A330-A-27-XX-3237-05ZZZ-920Z-A)
Modify the Electrical Harness 5870VB
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 9.00 h
Minimum Number of person 1
Elapsed Time 9.00 h
Skills Electrical
Material necessary to do the job
Part kit 273237D02R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
29 NSA935401-00 1 TIE
F9297001400400 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
AWM 27-98-08
20-33-00
20-33-44
ESPM
20-43-12
20-56-51
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
(b) Modify the electrical harness, refer to Ref. Fig. Removal of the Electrical Harness
5870VB.
1 Remove and reuse all installed labels item (161), item (162), item (163),
item (164) and item (165), as shown on SHEET 01.
2 Disconnect the wires from connectors 1CSD, 1CSH and 1CSK, as shown on
view A.
3 Remove, as shown on view A:

1 LIGHTN.PRO.SYS. Item (171) Retain

REV 00 Oct 12/20 A330-27-3237

Page 236
 A330
SERVICE BULLETIN

1 TRANSITION Item (172) Retain

1 LIGHTN.PRO.SYS. Item (173) Retain

1 LIGHTN.PRO.SYS. Item (174) Retain

1 LIGHTN.PRO.SYS. Item (175) Retain

1 TRANSITION Item (176) Retain

1 GROMMET Item (182) Discard

1 LIGHTN.PRO.SYS. Item (100) Discard

1 CABLE TIE Item (29) Discard

NOTE: Remove lock wire, if necessary.

4 Remove, as shown on view B and Ref. ESPM 20-43-12:

7 POLYOLEFINE SLEEVES Item (75) Discard

H

1 SLEEVE,SHRINKABLE Item (101) Discard

1 SLEEVE,SHRINKABLE Item (94) Discard

1 SLEEVE,SHRINKABLE Item (76) Discard

(c) Modify the wiring
Refer to Ref. ESPM 20-33-00
1 Remove the wire(s) as shown on this(these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Electrical Harness 5870VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5870VB
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. Wiring Diagram - Electrical Harness 5870VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5870VB
Ref. AWM 27-98-08.
(d) Put the heat shrink sleeve over the wires that go into the cross-junction, item
75, item 78, item 81, item 94 and item 101, refer to Ref. Fig. Installation of the
Electrical Harness 5870VB, SHEET 01 and Ref. ESPM 20-43-12, supplied in:

1 ELECTRICAL F9297001400400
EQUIPMENT
(e) Install the retained fitting conduit and lightning protection system, refer to Ref.
Fig. Installation of the Electrical Harness 5870VB, view A.

1 LIGHTN.PRO.SYS. Item (171) Retained

1 TRANSITION Item (172) Retained

1 LIGHTN.PRO.SYS. Item (173) Retained

1 LIGHTN.PRO.SYS. Item (174) Retained

REV 00 Oct 12/20 A330-27-3237

Page 237
 A330
SERVICE BULLETIN

1 LIGHTN.PRO.SYS. Item (175) Retained

1 TRANSITION Item (176) Retained

1 TIE-CABLE NSA935401-00 Item 29

(f) Install the new fitting conduit and lightning protection system, item 84, item 85,
item 102, item 103, item 104, item 105, item 106, item 150, item 151 and item
152, refer to Ref. Fig. Installation of the Electrical Harness 5870VB, view A and
view B, supplied in:

1 ELECTRICAL F9297001400400
EQUIPMENT
(g) Connect the wires to connectors 1CSD, 1CSH, 1CSK and 58CSR, refer to Ref. Fig.
Installation of the Electrical Harness 5870VB, view A.
(h) Install the new labels identified as 58CSR, item 89, and SB27–3237, item 74,
refer to Ref. Fig. Installation of the Electrical Harness 5870VB, view C, supplied
in:

1 ELECTRICAL F9297001400400
EQUIPMENT

REV 00 Oct 12/20 A330-27-3237

Page 238
 A330
SERVICE BULLETIN

CONF 002-004

TO
5202VC
5203VC
5219VC
5870VB
(161) 01

5870VB/FBW

5374VN /DC2
(162) 01
5393VN /B2
1CSK 2MFK
(161) 01 (164) 01
(161) 01
5870VB/FBW 1CS D
5870VB/FBW

TO FR80
(163) 01
(162) 01 1CSD
1CS K (162) 01
(162) 01
2MFK
2MFK
2MFK
(161) 01

5870VB/FBW

(162) 01

2MFK

(162) 01

2MFK
(161) 01

A 5870VB/FBW 1CSH 5870VB/FBW

(161) 01 (161) 01

5870VB/FBW
NOTE:
(162) 01 (165) 01 01 REMOVE AND REUSE ALL INSTALLED LABELS IN THIS AREA
THE SHOWN QUANTITY AND POSITION OF THE LABELS CAN DEVIATE FROM REALITY
2MFK 1CS H ALL CABLE TIES, ITEM 29, THAT FIXED THESE LABELS WILL BE DISCARDED

ICN-A330-A-27XX3237-A-FAPE3-0136O-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136O-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5870VB
Page 239
 A330
SERVICE BULLETIN

CONF 002-004

TO
5202VC
5203VC
5219VC

5870VB

5374VN /DC2 02

5393VN /B2

(171)

(182)
B
(29)
1CSK
TO FR80

(172)
1CSD

(100) (175)

(173)
(176)
(174)

1CSH

NOTE:
02 REMOVE LOCKWIRE IF NECESSARY
A
ICN-A330-A-27XX3237-A-FAPE3-0136P-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136P-A-002-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5870VB
Page 240
 A330
SERVICE BULLETIN

CONF 002-004

TO
5202VC
5203VC
5219VC

5870VB

(75)
5374VN /DC2

5393VN /B2 (94)

TO FR80

(75)
1CSK (75) (76)

1CSD

(75)
(75)

(75)

(101)

(75)
1CSH

WIRE
2798-5157 (B) 03
NOTE: WIRE
03 REMOVE WIRE
B 2798-5157 (R) 03
ICN-A330-A-27XX3237-A-FAPE3-0136Q-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136Q-A-001-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Removal of the Electrical Harness 5870VB
Page 241
 A330
SERVICE BULLETIN

CONF 002-004

BEFORE
FR56 FR80
2MF
H

7 2798-5157 R 15 V11
8 B 14 V12 RVDT 1 MON
9 2798-5158 R 2798-5159 R 12 V21
10 B B 11 V22

2MF FR91
A 3686VC 5205VP
1CS ACTUATOR THS
5949VC A
5870VB
D
B
C
J

AFTER

2MF 2MF
5212VT 7820VB
R 58CS
6
A R 3
F 2798-6835 5
B
B 4 2798-5048 B
G 1 R
FR56 FR80
2MF
H

7 2798-5157 R 2798-6834 R 15 V11

8 B B 14 V12 RVDT 1 MON
9 2798-5158 R 2798-5159 R 12 V21
10 B B 11 V22

2MF FR91
A 3686VC 5205VP
1CS ACTUATOR THS
5949VC A
5870VB
D
NEW WIRE B
NOTE: C
EXISTING WIRE
ONLY WIRES RELATED TO THIS J
SERVICE BULLETIN ARE SHOWN REROUTED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139O-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139O-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5870VB
Page 242
 A330
SERVICE BULLETIN

CONF 002-004

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 152 3686VC 8 EN3155-014M2018 2798-5157 B 2MF PN24 22980 904,7 310 1CS H 14 EN3155-019F2018 BEFORE

2 152 3686VC 7 EN3155-014M2018 2798-5157 R 2MF PN24 0 0 310 1CS H 15 EN3155-019F2018 BEFORE

3 152 3686VC 8 EN3155-014M2018 2798-5157 B 2MF PN24 22980 904,7 311 5212VT 6G EN3155-016M2018 AFTER

4 152 3686VC 7 EN3155-014M2018 2798-5157 R 2MF PN24 0 0 311 5212VT 6F EN3155-016M2018 AFTER

5 311 5212VT 6B EN3155-016M2018 2798-6835 B 2MF DRB24 5000 196,9 300 58CS R 5 EN3155-019F2018 A

6 311 5212VT 6A EN3155-016M2018 2798-6835 R 2MF DRB24 0 0 300 58CS R 3 EN3155-019F2018 A

7 300 58CS R 4 EN3155-019F2018 2798-6834 B 2MF DRB24 3000 118,1 310 1CS H 14 EN3155-019F2018 A

8 300 58CS R 1 EN3155-019F2018 2798-6834 R 2MF DRB24 0 0 310 1CS H 15 EN3155-019F2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70014 004 00 "SHEET 20,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C0-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5870VB
Page 243
 A330
SERVICE BULLETIN

CONF 002-004

TO
5202VC
5203VC
5219VC

5870VB

5374VN /DC2

5393VN /B2
94 TO FR80
75 TO 5212VT
A
75

75
1CSD 75
81

NEW WIRE 58CSR

2798-6834 (B) NEW WIRE
NEW WIRE 2798-6835 (B)
NEW WIRE 2798-6835 (R)
1CSK 2798-6834 (R)

78

75
75 75
NEW WIRE
2798-6835 (B)

NEW WIRE
2798-6835 (R)

NEW WIRE
2798-6834 (B) 101
75
78 NEW WIRE
2798-6834 (R)

1CSH

75

ICN-A330-A-27XX3237-A-FAPE3-0136F-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136F-A-001-01 SHEET 1/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5870VB
Page 244
 A330
SERVICE BULLETIN

CONF 002-004

5870VB

58CSR 5374VN /DC2 01

5393VN /B2

1CSK (171)
C
106

29

TO 5212VT
1CSD
(172)
84
102
85 B
(175)

104
103

81 151
(173) 150 85
152 151
(174)
103 84
78
(176)

1CSH

NOTE:
FOR CONNECTION OF THE CABLES
REFER TO MODIFICATION OF THE BUNDLE
WIRING IN THE ELECTRICAL
HARNESS 5870VB AND
AWM 27-98-08 A B
01 SECURE WITH LOCKWIRE IF NECESSARY 105
ICN-A330-A-27XX3237-A-FAPE3-013EQ-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013EQ-A-001-01 SHEET 2/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5870VB
Page 245
 A330
SERVICE BULLETIN

CONF 002-004

TO
5202VC
5203VC
5219VC
5870VB
5374VN /DC2 (161) 02

5393VN /B2 5870VB/FBW

(161) 02 (164) 02
(162) 02
5870VB/FBW 1CS D
2MFK

1CSK 1CSD
(162) 02
89
TO FR80
58CS R 2MFK
74

SB27-3237 (162) 02
58CSR
(163) 02
2MFK
(161) 02
1CS K
5870VB/FBW
(161) 02
(162) 02
5870VB/FBW

2MFK
(162) 02
(162) 02
2MFK
2MFK
(161) 02

5870VB/FBW 1CSH 5870VB/FBW

(162) 02
(161) 02
2MFK

NOTE:
(161) 02 02 REUSE ALL REMOVED LABELS IN THIS AREA.
INSTALL THE REMOVED LABELS AT THE SAME POSITION
5870VB/FBW 1CS H AS BEFORE THE MODIFICATION.
FIX ALL LABELS WITH CABLE TIES, ITEM 29
C (165) 02
ICN-A330-A-27XX3237-A-FAPE3-013ER-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-013ER-A-001-01 SHEET 3/3

REV 00 Oct 12/20 A330-27-3237
Installation of the Electrical Harness 5870VB
Page 246
 A330
SERVICE BULLETIN

CONF 001
(11) Task A330-A-27-XX-3237-02001-760A-A (A330-A-27-XX-3237-02ZZZ-760Z-A)
Reroute the cut wire
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical
Material necessary to do the job
Part kit 273237D09R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
73 NSA936603CC0100 1 CAP
F9297001300600 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
06-41-53, Page Block 001
20-33-00
20-33-44
ESPM
20-52-21
20-56-51
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
5 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
6 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
7 To install new wires, cut them to the necessary length, attach the terminals
and connect them.

REV 00 Oct 12/20 A330-27-3237

Page 247
 A330
SERVICE BULLETIN

(b) Modify the wiring

Refer to Ref. ESPM 20-33-00
1 Reroute and connect the wires as shown on this wiring diagram and the
related hook-up chart:
- Ref. Fig. Wiring Diagram - Electrical Harness 5871VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5869VB.
2 On the existing wire 2798-6836, install the sleeve identified as 2798-6836,
item 180, refer to Ref. Fig. Rerouting of the Cut Wire 2499-5020 to 5213VT,
view E, supplied in:

1 ELECTRICAL F9297001300600
EQUIPMENT

NOTE: Shrink the wire-identification sleeve to cover the existing wire.

3 Do a continuity test of the new and/or modified electrical wires, refer to

Ref. ESPM 20-52-21.
(c) To the disconnected wire 2499-5020, install:

1 CAP NSA936603CC0100 Item 73

(d) Stow the disconnected wire from 5871VB with cable ties, item 29, refer to Ref.
Fig. Rerouting of the Cut Wire 2499-5020 to 5213VT, view D.
(e) Install the Service Bulletin placard identified as SB27–3237, item 74, with cable
ties, item 29, refer to Ref. Fig. Rerouting of the Cut Wire 2499-5020 to 5213VT,
view D, supplied in:

1 ELECTRICAL F9297001300600
EQUIPMENT

REV 00 Oct 12/20 A330-27-3237

Page 248
 A330
SERVICE BULLETIN

CONF 001

BEFORE
5871VB 5871VB
FR56 FR80 FR86 FR91

1M 1M

16 2499-5020-DR20 2499-5020-DR20 G

A 3671VC 01 5123VC A
5205VP

AFTER
FR69

4
-A

5112VC A
5869VB 5871VB
5213VT
FR56 FR80 FR86 FR91

1MF 1M

16 2798-6836-DR20 2499-5020-DR20 G

A 3671VC 5123VC A
5205VP

NOTE: NOTE:
EXISTING WIRE
ONLY WIRES RELATED TO THIS 01 CUT THE WIRE CLOSE TO THE BEGINNING OF THE LIGHTNING PROTECTION HOSE
SERVICE BULLETIN ARE SHOWN REROUTED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139L-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139L-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5871VB
Page 249
 A330
SERVICE BULLETIN

CONF 001

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 21650 852,4 311 - - - BEFORE (5871VB)

5 150 5112VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 20000 787,4 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF PN24 3480 137,0 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF PN24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 006 00 "SHEET 33,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-0135K-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 250
 A330
SERVICE BULLETIN

CONF 001

Z310

FR91

FR87

FR86

FR85

FR84
FR83
5871VB /1M
FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-0137W-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137W-A-001-01 SHEET 1/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5020 to 5213VT
Page 251
 A330
SERVICE BULLETIN

CONF 001

TO
5123VC

FR87

FR86

5871VB /1M

FR85

TO
C 5205VP
5869VB /1MF

ICN-A330-A-27XX3237-A-FAPE3-0137X-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137X-A-002-01 SHEET 2/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5020 to 5213VT
Page 252
 A330
SERVICE BULLETIN

CONF 001

FR85

FR86

5213VT

5869VB /1MF
E

TO
5205VP

01 D

5871VB /1M

WIRE
2499-5020
STOWED
C

NOTE:
01 WIRE 2499-5020 (5871VB) REROUTED TO 5213VT
AND RENAMED TO 2798-6836 (5869VB)
ICN-A330-A-27XX3237-A-FAPE3-0137Y-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137Y-A-001-01 SHEET 3/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5020 to 5213VT
Page 253
 A330
SERVICE BULLETIN

CONF 001
FR86
01 73
5871VB /1M

29
02
WIRE 74 SB27-3237
2499-5020
STOWED

29

FR85
5869VB /1MF

D 5213VT

01
2798-6836 180 04

2798-6836 180 04

TO
5205VP
03 E
02

02
NOTE:
01 WIRE 2499-5020 (5871VB) REROUTED TO 5213VT AND RENAME TO 2798-6836 (5869VB)
02 REMOVE AND INSTALL NEW CABLE TIES, ITEM 29, IF NECESSARY
03 REMOVE AND REUSE IF NECESSARY
04 SHRINK NEW WIRE-IDENTIFICATION SLEEVE TO COVER THE EXISTING WIRE NUMBER
ICN-A330-A-27XX3237-A-FAPE3-0137Z-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137Z-A-001-01 SHEET 4/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5020 to 5213VT
Page 254
 A330
SERVICE BULLETIN

CONF 002-004
(11) Task A330-A-27-XX-3237-02002-760A-A (A330-A-27-XX-3237-02ZZZ-760Z-A)
Reroute the cut wire
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical
Material necessary to do the job
Part kit 273237D02R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
73 NSA936603CC0100 1 CAP
F9297001300700 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
06-41-53, Page Block 001
20-33-00
20-33-44
ESPM
20-52-21
20-56-51
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
5 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-44.
6 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
7 To install new wires, cut them to the necessary length, attach the terminals
and connect them.

REV 00 Oct 12/20 A330-27-3237

Page 255
 A330
SERVICE BULLETIN

(b) Modify the wiring

Refer to Ref. ESPM 20-33-00
1 Reroute and connect the wires as shown on this wiring diagram and the
related hook-up chart:
- Ref. Fig. Wiring Diagram - Electrical Harness 5871VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5869VB.
2 On the existing wire 2798-6836, install the sleeve identified as 2798-6836,
item 180, refer to Ref. Fig. Rerouting of the Cut Wire 2499-5020 to 5213VT,
view E, supplied in:

1 ELECTRICAL F9297001300700
EQUIPMENT

NOTE: Shrink the wire-identification sleeve to cover the existing wire.

3 Do a continuity test of the new and/or modified electrical wires, refer to

Ref. ESPM 20-52-21.
(c) To the disconnected wire 2499-5020, install:

1 CAP NSA936603CC0100 Item 73

(d) Stow the disconnected wire from 5871VB, with cable tie, item 29, refer to Ref.
Fig. Rerouting of the Cut Wire 2499-5020 to 5213VT, view D.
(e) Install the Service Bulletin placard identified as SB27–3237, item 74, with cable
ties, item 29, refer to Ref. Fig. Rerouting of the Cut Wire 2499-5020 to 5213VT,
view D, supplied in:

1 ELECTRICAL F9297001300700
EQUIPMENT

REV 00 Oct 12/20 A330-27-3237

Page 256
 A330
SERVICE BULLETIN

CONF 002-004

BEFORE
5871VB 5871VB
FR56 FR80 FR86 FR91

1M 1M

16 2499-5020-DR20 2499-5020-DR20 G

A 3671VC 01 5123VC A
5205VP

AFTER
FR69

4
-A

5112VC A
5869VB 5871VB
5213VT
FR56 FR80 FR86 FR91

1MF 1M

16 2798-6836-DR20 2499-5020-DR20 G

A 3671VC 5123VC A
5205VP

NOTE: NOTE:
EXISTING WIRE
ONLY WIRES RELATED TO THIS 01 CUT THE WIRE CLOSE TO THE BEGINNING OF THE LIGHTNING PROTECTION HOSE
SERVICE BULLETIN ARE SHOWN REROUTED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139L-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139L-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5871VB
Page 257
 A330
SERVICE BULLETIN

CONF 002-004

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 21650 852,4 311 - - - BEFORE (5871VB)

5 150 5112VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 20000 787,4 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF PF24 3340 131,5 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF PF24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 007 00 "SHEET 34,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C3-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 258
 A330
SERVICE BULLETIN

CONF 002-004

Z310

FR91

FR87

FR86

FR85

FR84
5871VB /1M
FR83
FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-0137P-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137P-A-001-01 SHEET 1/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5010 to 5213VT
Page 259
 A330
SERVICE BULLETIN

CONF 002-004

TO
5123VC

FR87

5871VB /1M

FR86 TO
5205VP

FR85

ICN-A330-A-27XX3237-A-FAPE3-0137Q-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137Q-A-001-01 SHEET 2/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5010 to 5213VT
Page 260
 A330
SERVICE BULLETIN

CONF 002-004

FR85
E

5213VT

5869VB /1MF
STGR8 FR86
TO
5205VP

01

5871VB /1M
TO
5123VC

WIRE
2499-5020
STOWED

NOTE:
01 WIRE 2499-5020 (5871VB) REROUTED TO 5213VT
AND RENAMED TO 2798-6836 (5869VB)
ICN-A330-A-27XX3237-A-FAPE3-0137R-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137R-A-001-01 SHEET 3/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5010 to 5213VT
Page 261
 A330
SERVICE BULLETIN

CONF 002-004
WIRE
2499-5020
STOWED
74
02 73 29
5871VB /1M SB27-3237

03 FR86

29

5869VB /1MF

5213VT

02 2798-6836 180 05

180 05
2798-6836
03
04

03 03

STGR8

TO
E 5205VP

NOTE: FR85
02 WIRE 2499-5020 (5871VB) REROUTED TO 5213VT AND RENAME TO 2798-6836 (5869VB)
03 INSTALL NEW CABLE TIES, ITEM 29, IF NECESSARY
04 REUSE IF NECESSARY
05 SHRINK NEW WIRE-IDENTIFICATION SLEEVE TO COVER THE EXISTING WIRE NUMBER
ICN-A330-A-27XX3237-A-FAPE3-0137S-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137S-A-001-01 SHEET 4/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5010 to 5213VT
Page 262
 A330
SERVICE BULLETIN

CONF 005
(11) Task A330-A-27-XX-3237-02012-760A-A (A330-A-27-XX-3237-02ZZZ-760Z-A)
Reroute the cut wire
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical
Material necessary to do the job
Part kit 273237D07R03
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
73 NSA936603CC0100 1 CAP
F9297001300800 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
06-41-53, Page Block 001
20-33-00
20-33-44
ESPM
20-52-21
20-56-51
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
5 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
6 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
7 To install new wires, cut them to the necessary length, attach the terminals
and connect them.

REV 00 Oct 12/20 A330-27-3237

Page 263
 A330
SERVICE BULLETIN

(b) Modify the wiring

Refer to Ref. ESPM 20-33-00
1 Reroute and connect the wires as shown on this wiring diagram and the
related hook-up chart:
- Ref. Fig. Wiring Diagram - Electrical Harness 5871VB and Ref. Fig.
Hook-up Chart of the Modification of the Wiring in Electrical Harness
5869VB.
2 On the existing wire 2798-6836, install the sleeve identified as 2798-6836,
item 180, refer to Ref. Fig. Rerouting of the Cut Wire 2499-5020 to 5213VT,
view E, supplied in:

1 ELECTRICAL F9297001300800
EQUIPMENT

NOTE: Shrink the wire-identification sleeve to cover the existing wire.

3 Do a continuity test of the new and/or modified electrical wires, refer to

Ref. ESPM 20-52-21.
(c) To the disconnected wire 2499-5020, install:

1 CAP NSA936603CC0100 Item 73

(d) Stow the disconnected wire from 5871VB, with cable tie, item 29, refer to Ref.
Fig. Rerouting of the Cut Wire 2499-5020 to 5213VT, view D.
(e) Install the Service Bulletin placard identified as SB27–3237, item 74, with cable
ties, item 29, refer to Ref. Fig. Rerouting of the Cut Wire 2499-5020 to 5213VT,
view D, supplied in:

1 ELECTRICAL F9297001300800
EQUIPMENT

REV 00 Oct 12/20 A330-27-3237

Page 264
 A330
SERVICE BULLETIN

CONF 005

BEFORE
5871VB 5871VB
FR56 FR80 FR86 FR91

1M 1M

16 2499-5020-DR20 2499-5020-DR20 G

A 3671VC 01 5123VC A
5205VP

AFTER
FR69

4
-A

5051VC A
5869VB 5871VB
5213VT
FR56 FR80 FR86 FR91

1MF 1M

16 2798-6836-DR20 2499-5020-DR20 G

A 3671VC 5123VC A
5205VP

NOTE: NOTE:
EXISTING WIRE
ONLY WIRES RELATED TO THIS 01 CUT THE WIRE CLOSE TO THE BEGINNING OF THE LIGHTNING PROTECTION HOSE
SERVICE BULLETIN ARE SHOWN REROUTED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139M-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139M-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5871VB
Page 265
 A330
SERVICE BULLETIN

CONF 005

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 19400 763,8 311 - - - BEFORE (5871VB)

5 150 5051VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 19400 763,8 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 3440 135,4 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 008 00 "SHEET 35,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C4-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 266
 A330
SERVICE BULLETIN

CONF 005

Z310

FR91

FR87

FR86

FR85

FR84
FR83
5871VB /1M
FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-0137W-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137W-A-001-01 SHEET 1/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5020 to 5213VT
Page 267
 A330
SERVICE BULLETIN

CONF 005

TO
5123VC

FR87

FR86

5871VB /1M

FR85

TO
C 5205VP
5869VB /1MF

ICN-A330-A-27XX3237-A-FAPE3-0137X-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137X-A-002-01 SHEET 2/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5020 to 5213VT
Page 268
 A330
SERVICE BULLETIN

CONF 005

FR85

FR86

5213VT

5869VB /1MF
E

TO
5205VP

01 D

5871VB /1M

WIRE
2499-5020
STOWED
C

NOTE:
01 WIRE 2499-5020 (5871VB) REROUTED TO 5213VT
AND RENAMED TO 2798-6836 (5869VB)
ICN-A330-A-27XX3237-A-FAPE3-0137Y-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137Y-A-001-01 SHEET 3/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5020 to 5213VT
Page 269
 A330
SERVICE BULLETIN

CONF 005
FR86
01 73
5871VB /1M

29
02
WIRE 74 SB27-3237
2499-5020
STOWED

29

FR85
5869VB /1MF

D 5213VT

01
2798-6836 180 04

2798-6836 180 04

TO
5205VP
03 E
02

02
NOTE:
01 WIRE 2499-5020 (5871VB) REROUTED TO 5213VT AND RENAME TO 2798-6836 (5869VB)
02 REMOVE AND INSTALL NEW CABLE TIES, ITEM 29, IF NECESSARY
03 REMOVE AND REUSE IF NECESSARY
04 SHRINK NEW WIRE-IDENTIFICATION SLEEVE TO COVER THE EXISTING WIRE NUMBER
ICN-A330-A-27XX3237-A-FAPE3-0137Z-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137Z-A-001-01 SHEET 4/4

REV 00 Oct 12/20 A330-27-3237
Rerouting of the Cut Wire 2499-5020 to 5213VT
Page 270
 A330
SERVICE BULLETIN

CONF 001
(12) Task A330-A-27-XX-3237-03001-720A-A (A330-A-27-XX-3237-03ZZZ-720Z-A)
Install the Modified Electrical Harness 5869VB Traverse
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 85 to Frame 86
Manpower/Resources/Skills

Man-hours 5.00 h
Minimum Number of person 1
Elapsed Time 5.00 h
Skills Electrical
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure

Part kit 273237D09R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 ABS0805-13 2 CLAMP
2 ABS0805-15 2 CLAMP
5 NAS1801-3-21 11 SCREW
7 NAS1149C0332R 17 WASHER
9 NSA5527-03-08 3 SPACER
10 NAS1291C3M 10 NUT
11 NSA5066-3-1 4 NUT
12 NSA5067-3-1 2 NUT
14 AS21919WCH09 1 CLAMP
15 AS21919WCH13 5 CLAMP
18 ABS0805-12 1 CLAMP
19 NSA5527-03-08D 9 SPACER
20 NAS1801-08-21 1 SCREW
21 NAS1801-3-9 9 SCREW
22 NSA935808C01 9 WASHER
23 NAS1149CN832R 1 WASHER
24 AS21919WCH10 1 CLAMP
25 ABS0805-09 4 CLAMP
26 ABS0805-10 3 CLAMP
27 AS21919WCH08 4 CLAMP

REV 00 Oct 12/20 A330-27-3237

Page 271
 A330
SERVICE BULLETIN

Part kit 273237D09R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F9297001300600 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM
Task 20-21-11-911-801
Task 20-28-00-912-810
20-33-00
20-33-42
20-33-44
20-51-20
ESPM
20-52-10
20-52-21
20-54-50
20-56-51
51-40-00
SRM
51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install the fasteners in accordance with Ref. SRM 51-42-00.
4 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
5 If alternative and substitute fasteners have to be used, you must make
sure that the associated nut/collar are compatible in accordance with refer
to Ref. SRM 51-40-00.
6 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
7 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
8 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
9 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
10 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
11 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
12 Adapt the clamp size as necessary, refer to Ref. ESPM 20-33-42.
(b) Install the electrical harness between Frame 86 and Frame 87.
Refer to Ref. Fig. Installation of the Modified Electrical Harness 5869VB at FR87.

REV 00 Oct 12/20 A330-27-3237

Page 272
 A330
SERVICE BULLETIN

Refer to Ref. ESPM 20-33-44 and Ref. AMM Task 20-21-11-911-801 for tightening.
1 Install, as shown on view E:

2 CLAMP-LOOP,CRS ABS0805-13 Item 1

2 CLAMP-LOOP,CRS ABS0805-15 Item 2

2 CLAMP AS21919WCH13 Item 15

1 CLAMP AS21919WCH10 Item 24

2 CLAMP-LOOP,CRS ABS0805-10 Item 26

with:

4 SCREW NAS1801-3-21 Item 5

3 SCREW NAS1801-3-9 Item 21

4 WASHER NSA935808C01 Item 22

5 WASHER NAS1149C0332R Item 7

4 SPACER NSA5527-03-08D Item 19

3 NUT NAS1291C3M Item 10

2 NUT-CLIP NSA5067-3-1 Item 12

1 NUT-CLIP NSA5066-3-1 Item 11

2 At the grounding points 5287VN, 6326VN25 and 6327VN25, as shown on
view F, install:

4 BONDING CABLE
with:

3 SCREW NAS1801-3-9 Item 21

3 WASHER NAS1149C0332R Item 7

3 NUT NAS1291C3M Item 10

3 Renew the protective finish with:

Primer Polyurethane 04EAC2

Paint - -
CorrosionInhibiting
Structure

Top Coat Polyurethane - 04JME4

- Grey InternalStructure
4 Attach the wires with cable tie, item 29, supplied in:

1 ELECTRICAL F9297001300600
EQUIPMENT
5 Install, as shown on view G:

1 CLAMP AS21919WCH09 Item 14

4 CLAMP-LOOP,CRS ABS0805-09 Item 25

1 CLAMP-LOOP,CRS ABS0805-10 Item 26

REV 00 Oct 12/20 A330-27-3237

Page 273
 A330
SERVICE BULLETIN

with:

5 SCREW NAS1801-3-21 Item 5

4 WASHER NSA935808C01 Item 22

3 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08 Item 9

4 SPACER NSA5527-03-08D Item 19

2 NUT NAS1291C3M Item 10

6 Install, as shown on view H:

1 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-3-9 Item 21

1 WASHER NAS1149C0332R Item 7

1 NUT-CLIP NSA5066-3-1 Item 11

7 Install, as shown on view J:

2 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-3-21 Item 5

1 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08 Item 9

1 NUT-CLIP NSA5066-3-1 Item 11

8 Install, as shown on view K:

1 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-08-21 Item 20

1 WASHER NAS1149CN832R Item 23

1 SPACER NSA5527-03-08 Item 9

9 Install, as shown on view L:

1 CLAMP AS21919WCH13 Item 15

with:

1 SCREW NAS1801-3-9 Item 21

1 WASHER NAS1149C0332R Item 7

1 NUT-CLIP NSA5066-3-1 Item 11

10 Install, as shown on view M:

2 CLAMP AS21919WCH13 Item 15

with:

REV 00 Oct 12/20 A330-27-3237

Page 274
 A330
SERVICE BULLETIN

1 SCREW NAS1801-3-9 Item 21

2 WASHER NAS1149C0332R Item 7

1 NUT NAS1291C3M Item 10

11 Install, as shown on view N:

1 CLAMP-LOOP,CRS ABS0805-12 Item 18

with:

1 SCREW NAS1801-3-21 Item 5

1 WASHER NSA935808C01 Item 22

1 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08D Item 19

1 NUT NAS1291C3M Item 10

12 Install the Service Bulletin placard identified as SB27–3237, item 74, with
cable ties, item 34, as shown on view N, supplied in:

1 ELECTRICAL F9297001300600
EQUIPMENT
13 Install the sleeve identified as 2798–5041, item 82, as shown on view P:

1 ELECTRICAL F9297001300600
EQUIPMENT
14 Install and connect the wire, as shown on view P:
- Refer to Ref. Fig. Wiring Diagram - Electrical Harness 5869VB and
Ref. Fig. Hook-up Chart of the Modification of the Wiring in Electrical
Harness 5869VB.
15 Install the placards, item 74, item 89 and item 137, with cable ties, item
34, as shown on view P, supplied in:

1 ELECTRICAL F9297001300600
EQUIPMENT
16 Do a continuity test of the new and/or modified electrical wires, refer to
Ref. ESPM 20-52-21.
17 Connect (and lock when relevant) the connectors 1CSJ, 1CSB, 1CSG and
58CSS.

REV 00 Oct 12/20 A330-27-3237

Page 275
 A330
SERVICE BULLETIN

CONF 001

Z310

FR91

FR87

FR86

FR85

FR84

5869VB /1MF FR83

FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-0138H-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138H-A-001-01 SHEET 1/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 276
 A330
SERVICE BULLETIN

CONF 001
TO
5219VC
5202VC
5203VC

G
E
FR87

1CSB
TO
1CSJ
58CSS

5287VN /DC1
6326VN25 /DC1 1CSG
6327VN25 /B1
C
FR86
5869VB /1MF
M
N

FR85

TO
5213VT
TO
5205VP
D

ICN-A330-A-27XX3237-A-FAPE3-0138I-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138I-A-002-01 SHEET 2/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 277
 A330
SERVICE BULLETIN

CONF 001

FR87

K
5287VN /DC1
6326VN25 /DC1
6327VN25 /B1

1CSJ

58CSS
1CSB

5869VB /1MF
H

TO
1CSG

ICN-A330-A-27XX3237-A-FAPE3-0138J-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138J-A-002-01 SHEET 3/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 278
 A330
SERVICE BULLETIN

CONF 001

FR85

FR86

5213VT

TO
5205VP

5869VB /1MF

ICN-A330-A-27XX3237-A-FAPE3-0138K-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138K-A-001-01 SHEET 4/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 279
 A330
SERVICE BULLETIN

CONF 001

5
22 TO
5219VC FR87
5202VC
1 5203VC

5869VB /1MF
2

1 19

19 10
2

24

21
7

21 11
7

15
TO
5 26 1CSJ

12 22
TO
19 26 1CSB
12 1CSG
7
10
7 15
21
TO 19
5205VP
E
5287VN /DC1
6326VN25 /DC1
NOTE:
6327VN25 /B1 F
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0138L-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138L-A-001-01 SHEET 5/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 280
 A330
SERVICE BULLETIN

CONF 001
5
FR87
5869VB /1MF 7
21

6327VN25 /B1 5869VB /1MF

6326VN25 /DC1

7 5
22 14

25

9
5 25

22
5870VB /2MF
10 25 19
29 5287VN /DC1

25 7
F 19 10

26 7
FR87 19 10
FR87 FR87

19 G
5870VB /2MF

9 27 21
7
5
7
27 5870VB /2MF
5869VB /1MF
23

27 9
20
K 5869VB /1MF

27
11
J H
NOTE: 11
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0138M-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138M-A-001-01 SHEET 6/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 281
 A330
SERVICE BULLETIN

CONF 001

11
FR87

21
7

15 10

15

5869VB /1MF
15

L 7 5871VB /1M

21

M
19
7
5
10
22 74

SB27-3237

34

18
5869VB /1MF
5871VB /1M
01
FR86 NEW WIRE
2798-5041 (B)
N 2798-5041 (R)
01 NEW WIRE
NOTE:
2798-5046
ELECTRICAL BONDING
01 INSTALL NEW CABLE TIES, ITEM 34, IF NECESSARY ICN-A330-A-27XX3237-A-FAPE3-0138N-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138N-A-001-01 SHEET 7/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 282
 A330
SERVICE BULLETIN

CONF 001

FR85

5213VT
82 (2798-6836)
2798-5041
NEW WIRE
03 2798-5041 (B)
2798-5041 (R)

03 NEW WIRE
2798-5046

34

74 SB27-3237

5869VB/FBW
89
F92970013001
34

34

137 1MF
02
5869VB /1MF
01

NOTE:
01 INSTALL NEW CABLE TIES, ITEM 34, IF NECESSAY
02 TIGHTEN THE CLAMP IF NECESSARY
03 CUT TO LENGTH ON ASSEMBLY
ICN-A330-A-27XX3237-A-FAPE3-0138O-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138O-A-001-01 SHEET 8/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 283
 A330
SERVICE BULLETIN

CONF 001

BEFORE
1MF
5869VB
B 1
2798-5041-PN24
R 2

1
E G 1CS

2
E

4
D

5213VT

AFTER
1MF
5869VB
B 1
2798-5041-DRB24
R 2

1
E G 1CS

2
E 1MF

4 6326VN25 /DC1 2798-5045-DR18 2

D 2798-5046-DR18 1
6327VN25 /B1 2798-5047-DR18 3
5213VT

S 58CS

NOTE:
ONLY WIRES RELATED TO THIS NEW WIRE
SERVICE BULLETIN ARE SHOWN DELETED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5869VB
Page 284
 A330
SERVICE BULLETIN

CONF 001

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 21650 852,4 311 - - - BEFORE (5871VB)

5 150 5112VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 20000 787,4 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF PN24 3480 137,0 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF PN24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 006 00 "SHEET 33,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-0135K-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 285
 A330
SERVICE BULLETIN

CONF 002-004
(12) Task A330-A-27-XX-3237-03002-720A-A (A330-A-27-XX-3237-03ZZZ-720Z-A)
Install the Modified Electrical Harness 5869VB V-Prop
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 85 to Frame 86
Manpower/Resources/Skills

Man-hours 5.00 h
Minimum Number of person 1
Elapsed Time 5.00 h
Skills Electrical
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure

Part kit 273237D02R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 ABS0805-13 6 CLAMP
5 NAS1801-3-21 7 SCREW
6 NAS1096-3-8 4 SCREW
7 NAS1149C0332R 12 WASHER
8 NSA5527-03-03D 2 SPACER
9 NSA5527-03-08 1 SPACER
10 NAS1291C3M 11 NUT
11 NSA5066-3-1 2 NUT
12 NSA5067-3-1 1 NUT
19 NSA5527-03-08D 8 SPACER
21 NAS1801-3-9 4 SCREW
22 NSA935808C01 13 WASHER
24 AS21919WCH10 2 CLAMP
25 ABS0805-09 9 CLAMP
26 ABS0805-10 2 CLAMP
27 AS21919WCH08 2 CLAMP
43 ABS0805-07 3 CLAMP
44 NAS1801-3-28 2 SCREW
45 NSA5527-03-02D 2 SPACER
F9297001300700 1 ELECEQPT

REV 00 Oct 12/20 A330-27-3237

Page 286
 A330
SERVICE BULLETIN

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM
Task 20-21-11-911-801
Task 20-28-00-912-810
20-33-00
20-33-42
20-33-44
20-51-20
ESPM
20-52-10
20-52-21
20-54-50
20-56-51
51-40-00
SRM
51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install the fasteners in accordance with Ref. SRM 51-42-00.
4 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
5 If alternative and substitute fasteners have to be used, you must make
sure that the associated nut/collar are compatible in accordance with refer
to Ref. SRM 51-40-00.
6 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
7 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
8 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
9 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
10 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
11 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
12 Adapt the clamp size as necessary, refer to Ref. ESPM 20-33-42.
(b) Install the electrical harness between Frame 85 and Frame 87.
Refer to Ref. Fig. Installation of the Modified Electrical Harness 5869VB at FR87.
Refer to Ref. ESPM 20-33-44 and Ref. AMM Task 20-21-11-911-801 for tightening.
1 Install, as shown on view C:

7 CLAMP-LOOP,CRS ABS0805-09 Item 25

REV 00 Oct 12/20 A330-27-3237

Page 287
 A330
SERVICE BULLETIN

3 CLAMP-LOOP,CRS ABS0805-07 Item 43

with:

6 SCREW NAS1801-3-21 Item 5

6 WASHER NSA935808C01 Item 22

6 SPACER NSA5527-03-08D Item 19

5 WASHER NAS1149C0332R Item 7

5 NUT NAS1291C3M Item 10

2 Install, as shown on view D:

2 CLAMP-LOOP,CRS ABS0805-09 Item 25

2 CLAMP-LOOP,CRS ABS0805-10 Item 26

with:

2 SCREW NAS1801-3-28 Item 44

4 WASHER NSA935808C01 Item 22

2 SPACER NSA5527-03-03D Item 8

2 SPACER NSA5527-03-08D Item 19

2 NUT NAS1291C3M Item 10

3 At the grounding points 5287VN, 6327VN and 6328VN, as shown on view
D, install:

3 BONDING CABLE
with:

3 SCREW NAS1801-3-9 Item 21

3 WASHER NAS1149C0332R Item 7

3 NUT NAS1291C3M Item 10

4 Renew the protective finish with:

Primer Polyurethane 04EAC2

Paint - -
CorrosionInhibiting
Structure

Top Coat Polyurethane - 04JME4

- Grey InternalStructure
5 Install, as shown on view E:

2 CLAMP AS21919WCH10 Item 24

with:

1 SCREW NAS1096-3-8 Item 6

1 WASHER NAS1149C0332R Item 7

1 NUT-CLIP NSA5067-3-1 Item 12

REV 00 Oct 12/20 A330-27-3237

Page 288
 A330
SERVICE BULLETIN

6 Install, as shown on view F:

1 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-3-9 Item 21

1 WASHER NAS1149C0332R Item 7

1 NUT-CLIP NSA5066-3-1 Item 11

7 Install, as shown on view G:

4 CLAMP-LOOP,CRS ABS0805-13 Item 1

with:

2 SCREW NAS1096-3-8 Item 6

2 WASHER NSA935808C01 Item 22

1 WASHER NAS1149C0332R Item 7

2 SPACER NSA5527-03-02D Item 45

1 NUT NAS1291C3M Item 10

8 Install, as shown on view H:

1 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-3-21 Item 5

1 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08 Item 9

1 NUT-CLIP NSA5066-3-1 Item 11

9 Install, as shown on view K:

2 CLAMP-LOOP,CRS ABS0805-13 Item 1

with:

1 SCREW NAS1096-3-8 Item 6

1 WASHER NSA935808C01 Item 22

10 Install the Service Bulletin placard identified as SB27–3237, item 74, with
cable ties, item 29, as shown on view K, supplied in:

1 ELECTRICAL F9297001300700
EQUIPMENT
11 Install the sleeve identified as 2798–5041, item 82, as shown on view L,
supplied in:

1 ELECTRICAL F9297001300700
EQUIPMENT
12 Install and connect the wire, as shown on view L:
- Refer to Ref. Fig. Wiring Diagram - Electrical Harness 5869VB and
Ref. Fig. Hook-up Chart of the Modification of the Wiring in Electrical
Harness 5869VB.

REV 00 Oct 12/20 A330-27-3237

Page 289
 A330
SERVICE BULLETIN

13 Install the placards, item 74, item 89 and item 137, with cable ties, item
34, as shown on view L, supplied in:

1 ELECTRICAL F9297001300700
EQUIPMENT
14 Do a continuity test of the new and/or modified electrical wires, refer to
Ref. ESPM 20-52-21.
15 Connect (and lock when relevant) the connectors 1CSJ, 1CSB, 1CSG and
58CSS.

REV 00 Oct 12/20 A330-27-3237

Page 290
 A330
SERVICE BULLETIN

CONF 002-004

Z310

FR91

FR87

FR86

FR85

FR84
FR83
5869VB /1MF
FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-01380-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01380-A-001-01 SHEET 1/6

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 291
 A330
SERVICE BULLETIN

CONF 002-004

TO
5219VC
5202VC
5203VC

H
C
1CSB
FR87
G TO
1CSJ

F 58CSS
J
1CSG
E

5287VN /DC1 5869VB /1MF

6326VN25 /DC1
6327VN25 /B1

FR86 TO
5205VP
D

FR85

ICN-A330-A-27XX3237-A-FAPE3-01381-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01381-A-001-01 SHEET 2/6

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 292
 A330
SERVICE BULLETIN

CONF 002-004
10 7 FR87

5871VB /1M 22
10 7 FR87
19
25

10
10 19
10 25
7 7
5869VB /1MF

25 19
19 19
10
25 22 25
7
5 8

19 25
8
19
43
25
19 43 5870VB /2MF
26
25
22 5287VN /DC1
43
6327VN /B1 10

25
5 22
22
7 44
5
21
6328VN /DC1
5867VB /1SF
C 22
5 26
5869VB /1MF
5869VB /1MF 5871VB /1M D

6 24
7

24

E
12
NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-01382-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01382-A-002-01 SHEET 3/6

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 293
 A330
SERVICE BULLETIN

CONF 002-004

10

5869VB /1MF 27 21
7 45

1
45

1
5869VB /1MF
11
5871VB /1M
1
1
F

22

G 6

11 FR87
5
7

27 9

5869VB /1MF

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-01383-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01383-A-002-01 SHEET 4/6

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 294
 A330
SERVICE BULLETIN

CONF 002-004

FR85

5213VT
L

STGR8 FR86
TO
5205VP

5871VB /1M

K
5869VB /1MF

TO
58CS

ICN-A330-A-27XX3237-A-FAPE3-01384-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01384-A-001-01 SHEET 5/6

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 295
 A330
SERVICE BULLETIN

CONF 002-004
FR86

74

SB27-3237
1
5869VB /1MF
29

NEW WIRE
2798-5046
5871VB /1M 01

1
01
22
K 6 NEW WIRE
2798-5041 (B)
2798-5041 (R)

NEW WIRE
2798-5041 (B) 03
5213VT 2798-5041 (R)
82
2798-5041
STGR8
03
(2798-6836)

NEW WIRE 03
2798-5046

01

5869VB/FBW 02
89 01
F92970013001

137 1MF 74 SB27-3237

34 x6
NOTE:
ELECTRICAL BONDING L TO
5205VP
01 INSTALL NEW CABLE TIES, ITEM 34,
IF NECESSAY
02 TIGHTEN THE CLAMP IF NECESSARY
FR85
03 CUT TO LENGTH ON ASSEMBLY ICN-A330-A-27XX3237-A-FAPE3-01385-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-01385-A-001-01 SHEET 6/6

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 296
 A330
SERVICE BULLETIN

CONF 002-004

BEFORE
1MF
5869VB
B 1
2798-5041-PN24
R 2

1
E G 1CS

2
E

4
D

5213VT

AFTER
1MF
5869VB
B 1
2798-5041-DRB24
R 2

1
E G 1CS

2
E 1MF

4 6326VN25 /DC1 2798-5045-DR18 2

D 2798-5046-DR18 1
6327VN25 /B1 2798-5047-DR18 3
5213VT

S 58CS

NOTE:
ONLY WIRES RELATED TO THIS NEW WIRE
SERVICE BULLETIN ARE SHOWN DELETED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5869VB
Page 297
 A330
SERVICE BULLETIN

CONF 002-004

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 21650 852,4 311 - - - BEFORE (5871VB)

5 150 5112VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 20000 787,4 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF PF24 3340 131,5 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF PF24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 007 00 "SHEET 34,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C3-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 298
 A330
SERVICE BULLETIN

CONF 005
(12) Task A330-A-27-XX-3237-03012-720A-A (A330-A-27-XX-3237-03ZZZ-720Z-A)
Install the Modified Electrical Harness 5869VB Traverse
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 85 to Frame 86
Manpower/Resources/Skills

Man-hours 5.00 h
Minimum Number of person 1
Elapsed Time 5.00 h
Skills Electrical
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure

Part kit 273237D07R03

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 ABS0805-13 2 CLAMP
2 ABS0805-15 2 CLAMP
5 NAS1801-3-21 11 SCREW
7 NAS1149C0332R 17 WASHER
9 NSA5527-03-08 3 SPACER
10 NAS1291C3M 10 NUT
11 NSA5066-3-1 4 NUT
12 NSA5067-3-1 2 NUT
14 AS21919WCH09 1 CLAMP
15 AS21919WCH13 5 CLAMP
18 ABS0805-12 1 CLAMP
19 NSA5527-03-08D 9 SPACER
20 NAS1801-08-21 1 SCREW
21 NAS1801-3-9 9 SCREW
22 NSA935808C01 9 WASHER
23 NAS1149CN832R 1 WASHER
24 AS21919WCH10 1 CLAMP
25 ABS0805-09 4 CLAMP
26 ABS0805-10 3 CLAMP
27 AS21919WCH08 4 CLAMP

REV 00 Oct 12/20 A330-27-3237

Page 299
 A330
SERVICE BULLETIN

Part kit 273237D07R03

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F9297001300800 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM
Task 20-21-11-911-801
Task 20-28-00-912-810
20-33-00
20-33-42
20-33-44
20-51-20
ESPM
20-52-10
20-52-21
20-54-50
20-56-51
51-40-00
SRM
51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install the fasteners in accordance with Ref. SRM 51-42-00.
4 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
5 If alternative and substitute fasteners have to be used, you must make
sure that the associated nut/collar are compatible in accordance with refer
to Ref. SRM 51-40-00.
6 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
7 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
8 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
9 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
10 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
11 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
12 Adapt the clamp size as necessary, refer to Ref. ESPM 20-33-42.
(b) Install the electrical harness between Frame 86 and Frame 87.
Refer to Ref. Fig. Installation of the Modified Electrical Harness 5869VB at FR87.

REV 00 Oct 12/20 A330-27-3237

Page 300
 A330
SERVICE BULLETIN

Refer to Ref. ESPM 20-33-44 and Ref. AMM Task 20-21-11-911-801 for tightening.
1 Install, as shown on view E:

2 CLAMP-LOOP,CRS ABS0805-13 Item 1

2 CLAMP-LOOP,CRS ABS0805-15 Item 2

2 CLAMP AS21919WCH13 Item 15

1 CLAMP AS21919WCH10 Item 24

2 CLAMP-LOOP,CRS ABS0805-10 Item 26

with:

4 SCREW NAS1801-3-21 Item 5

3 SCREW NAS1801-3-9 Item 21

4 WASHER NSA935808C01 Item 22

5 WASHER NAS1149C0332R Item 7

4 SPACER NSA5527-03-08D Item 19

3 NUT NAS1291C3M Item 10

2 NUT-CLIP NSA5067-3-1 Item 12

1 NUT-CLIP NSA5066-3-1 Item 11

2 At the grounding points 5287VN, 6326VN25 and 6327VN25, as shown on
view F, install:

4 BONDING CABLE
with:

3 SCREW NAS1801-3-9 Item 21

3 WASHER NAS1149C0332R Item 7

3 NUT NAS1291C3M Item 10

3 Renew the protective finish with:

Primer Polyurethane 04EAC2

Paint - -
CorrosionInhibiting
Structure

Top Coat Polyurethane - 04JME4

- Grey InternalStructure
4 Attach the wires with cable ties, item 29, supplied in:

1 ELECTRICAL F9297001300800
EQUIPMENT
5 Install, as shown on view G:

1 CLAMP AS21919WCH09 Item 14

4 CLAMP-LOOP,CRS ABS0805-09 Item 25

1 CLAMP-LOOP,CRS ABS0805-10 Item 26

REV 00 Oct 12/20 A330-27-3237

Page 301
 A330
SERVICE BULLETIN

with:

5 SCREW NAS1801-3-21 Item 5

4 WASHER NSA935808C01 Item 22

3 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08 Item 9

4 SPACER NSA5527-03-08D Item 19

2 NUT NAS1291C3M Item 10

6 Install, as shown on view H:

1 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-3-9 Item 21

1 WASHER NAS1149C0332R Item 7

1 NUT-CLIP NSA5066-3-1 Item 11

7 Install, as shown on view J:

2 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-3-21 Item 5

1 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08 Item 9

1 NUT-CLIP NSA5066-3-1 Item 11

8 Install, as shown on view K:

1 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-08-21 Item 20

1 WASHER NAS1149CN832R Item 23

1 SPACER NSA5527-03-08 Item 9

9 Install, as shown on view L:

1 CLAMP AS21919WCH13 Item 15

with:

1 SCREW NAS1801-3-9 Item 21

1 WASHER NAS1149C0332R Item 7

1 NUT-CLIP NSA5066-3-1 Item 11

10 Install, as shown on view M:

2 CLAMP AS21919WCH13 Item 15

with:

REV 00 Oct 12/20 A330-27-3237

Page 302
 A330
SERVICE BULLETIN

1 SCREW NAS1801-3-9 Item 21

2 WASHER NAS1149C0332R Item 7

1 NUT NAS1291C3M Item 10

11 Install, as shown on view N:

1 CLAMP-LOOP,CRS ABS0805-12 Item 18

with:

1 SCREW NAS1801-3-21 Item 5

1 WASHER NSA935808C01 Item 22

1 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08D Item 19

1 NUT NAS1291C3M Item 10

12 Install the Service Bulletin placard identified as SB27–3237, item 74, with
cable ties, item 34, as shown on view N, supplied in:

1 ELECTRICAL F9297001300800
EQUIPMENT
13 Install the sleeve identified as 2798–5041, item 82, as shown on view P:

1 ELECTRICAL F9297001300800
EQUIPMENT
14 Install and connect the wire, as shown on view P:
- Refer to Ref. Fig. Wiring Diagram - Electrical Harness 5869VB and
Ref. Fig. Hook-up Chart of the Modification of the Wiring in Electrical
Harness 5869VB.
15 Install the placards, item 74, item 89 and item 137, with cable ties, item
34, as shown on view P, supplied in:

1 ELECTRICAL F9297001300800
EQUIPMENT
16 Do a continuity test of the new and/or modified electrical wires, refer to
Ref. ESPM 20-52-21.
17 Connect (and lock when relevant) the connectors 1CSJ, 1CSB, 1CSG and
58CSS.

REV 00 Oct 12/20 A330-27-3237

Page 303
 A330
SERVICE BULLETIN

CONF 005

Z310

FR91

FR87

FR86

FR85

FR84

5869VB /1MF FR83

FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-0138H-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138H-A-001-01 SHEET 1/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 304
 A330
SERVICE BULLETIN

CONF 005
TO
5219VC
5202VC
5203VC

G
E
FR87

1CSB
TO
1CSJ
58CSS

5287VN /DC1
6326VN25 /DC1 1CSG
6327VN25 /B1
C
FR86
5869VB /1MF
M
N

FR85

TO
5213VT
TO
5205VP
D

ICN-A330-A-27XX3237-A-FAPE3-0138I-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138I-A-002-01 SHEET 2/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 305
 A330
SERVICE BULLETIN

CONF 005

FR87

K
5287VN /DC1
6326VN25 /DC1
6327VN25 /B1

1CSJ

58CSS
1CSB

5869VB /1MF
H

TO
1CSG

ICN-A330-A-27XX3237-A-FAPE3-0138J-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138J-A-002-01 SHEET 3/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 306
 A330
SERVICE BULLETIN

CONF 005

FR85

FR86

5213VT

TO
5205VP

5869VB /1MF

ICN-A330-A-27XX3237-A-FAPE3-0138K-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138K-A-001-01 SHEET 4/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 307
 A330
SERVICE BULLETIN

CONF 005

5
22 TO
5219VC FR87
5202VC
1 5203VC

5869VB /1MF
2

1 19

19 10
2

24

21
7

21 11
7

15
TO
5 26 1CSJ

12 22
TO
19 26 1CSB
12 1CSG
7
10
7 15
21
TO 19
5205VP
E
5287VN /DC1
6326VN25 /DC1
NOTE:
6327VN25 /B1 F
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0138L-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138L-A-001-01 SHEET 5/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 308
 A330
SERVICE BULLETIN

CONF 005
5
FR87
5869VB /1MF 7
21

6327VN25 /B1 5869VB /1MF

6326VN25 /DC1

7 5
22 14

25

9
5 25

22
5870VB /2MF
10 25 19
29 5287VN /DC1

25 7
F 19 10

26 7
FR87 19 10
FR87 FR87

19 G
5870VB /2MF

9 27 21
7
5
7
27 5870VB /2MF
5869VB /1MF
23

27 9
20
K 5869VB /1MF

27
11
J H
NOTE: 11
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0138M-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138M-A-001-01 SHEET 6/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 309
 A330
SERVICE BULLETIN

CONF 005

11
FR87

21
7

15 10

15

5869VB /1MF
15

L 7 5871VB /1M

21

M
19
7
5
10
22 74

SB27-3237

34

18
5869VB /1MF
5871VB /1M
01
FR86 NEW WIRE
2798-5041 (B)
N 2798-5041 (R)
01 NEW WIRE
NOTE:
2798-5046
ELECTRICAL BONDING
01 INSTALL NEW CABLE TIES, ITEM 34, IF NECESSARY ICN-A330-A-27XX3237-A-FAPE3-0138N-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138N-A-001-01 SHEET 7/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 310
 A330
SERVICE BULLETIN

CONF 005

FR85

5213VT
82 (2798-6836)
2798-5041
NEW WIRE
03 2798-5041 (B)
2798-5041 (R)

03 NEW WIRE
2798-5046

34

74 SB27-3237

5869VB/FBW
89
F92970013001
34

34

137 1MF
02
5869VB /1MF
01

NOTE:
01 INSTALL NEW CABLE TIES, ITEM 34, IF NECESSAY
02 TIGHTEN THE CLAMP IF NECESSARY
03 CUT TO LENGTH ON ASSEMBLY
ICN-A330-A-27XX3237-A-FAPE3-0138O-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0138O-A-001-01 SHEET 8/8

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5869VB at FR87
Page 311
 A330
SERVICE BULLETIN

CONF 005

BEFORE
1MF
5869VB
B 1
2798-5041-PN24
R 2

1
E G 1CS

2
E

4
D

5213VT

AFTER
1MF
5869VB
B 1
2798-5041-DRB24
R 2

1
E G 1CS

2
E 1MF

4 6326VN25 /DC1 2798-5045-DR18 2

D 2798-5046-DR18 1
6327VN25 /B1 2798-5047-DR18 3
5213VT

S 58CS

NOTE:
ONLY WIRES RELATED TO THIS NEW WIRE
SERVICE BULLETIN ARE SHOWN DELETED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139N-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5869VB
Page 312
 A330
SERVICE BULLETIN

CONF 005

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 19400 763,8 311 - - - BEFORE (5871VB)

5 150 5051VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 19400 763,8 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 3440 135,4 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 008 00 "SHEET 35,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C4-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 313
 A330
SERVICE BULLETIN

CONF 001
(13) Task A330-A-27-XX-3237-04001-720A-A (A330-A-27-XX-3237-04ZZZ-720Z-A)
Install the Modified Electrical Harness 5870VB Traverse
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 6.00 h
Minimum Number of person 1
Elapsed Time 6.00 h
Skills Electrical
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure

Part kit 273237D01R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F9297001400400 1 ELECEQPT

Part kit 273237D09R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
5 NAS1801-3-21 10 SCREW
7 NAS1149C0332R 11 WASHER
9 NSA5527-03-08 3 SPACER
10 NAS1291C3M 8 NUT
11 NSA5066-3-1 1 NUT
14 AS21919WCH09 1 CLAMP
18 ABS0805-12 3 CLAMP
19 NSA5527-03-08D 8 SPACER
20 NAS1801-08-21 1 SCREW
21 NAS1801-3-9 3 SCREW
22 NSA935808C01 8 WASHER
23 NAS1149CN832R 1 WASHER
24 AS21919WCH10 1 CLAMP
25 ABS0805-09 2 CLAMP
26 ABS0805-10 2 CLAMP
27 AS21919WCH08 1 CLAMP
66 AS21919WCH12 2 CLAMP
67 ABS0805-11 2 CLAMP

REV 00 Oct 12/20 A330-27-3237

Page 314
 A330
SERVICE BULLETIN

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM
Task 20-21-11-911-801
Task 20-28-00-912-810
20-33-00
20-33-42
20-33-44
20-51-20
ESPM
20-52-10
20-52-21
20-54-50
20-56-51
51-40-00
SRM
51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install the fasteners in accordance with Ref. SRM 51-42-00.
4 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
5 If alternative and substitute fasteners have to be used, you must make
sure that the associated nut/collar are compatible in accordance with refer
to Ref. SRM 51-40-00.
6 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
7 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
8 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
9 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
10 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
11 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
12 Adapt the clamp size as necessary, refer to Ref. ESPM 20-33-42.
(b) Install the electrical harness between Frame 85 and Frame 87.
Refer to Ref. Fig. Installation of the Modified Electrical Harness 5870VB at FR87.
Refer to Ref. ESPM 20-33-44 and Ref. AMM Task 20-21-11-911-801 for tightening.
1 Install, as shown on view D:

2 CLAMP-LOOP,CRS ABS0805-09 Item 25

REV 00 Oct 12/20 A330-27-3237

Page 315
 A330
SERVICE BULLETIN

1 CLAMP-LOOP,CRS ABS0805-10 Item 26

with:

3 SCREW NAS1801-3-21 Item 5

3 WASHER NSA935808C01 Item 22

3 SPACER NSA5527-03-08D Item 19

1 WASHER NAS1149C0332R Item 7

1 NUT NAS1291C3M Item 10

2 Install, as shown on view E:

1 CLAMP-LOOP,CRS ABS0805-10 Item 26

1 CLAMP-LOOP,CRS ABS0805-12 Item 18

1 CLAMP AS21919WCH12 Item 66

with:

3 SCREW NAS1801-3-21 Item 5

2 WASHER NSA935808C01 Item 22

2 WASHER NAS1149C0332R Item 7

2 SPACER NSA5527-03-08D Item 19

1 SPACER NSA5527-03-08 Item 9

1 NUT NAS1291C3M Item 10

3 At the grounding points 5374VN and 5393VN, as shown on view D, install:

3 BONDING CABLE
with:

2 SCREW NAS1801-3-9 Item 21

2 WASHER NAS1149C0332R Item 7

2 NUT NAS1291C3M Item 10

4 Renew the protective finish with:

Primer Polyurethane 04EAC2

Paint - -
CorrosionInhibiting
Structure

Top Coat Polyurethane - 04JME4

- Grey InternalStructure
5 Install, as shown on view F:

2 CLAMP-LOOP,CRS ABS0805-12 Item 18

1 CLAMP-LOOP,CRS ABS0805-11 Item 67

with:

2 SCREW NAS1801-3-21 Item 5

REV 00 Oct 12/20 A330-27-3237

Page 316
 A330
SERVICE BULLETIN

2 WASHER NSA935808C01 Item 22

2 WASHER NAS1149C0332R Item 7

2 SPACER NSA5527-03-08D Item 19

2 NUT NAS1291C3M Item 10

6 Install, as shown on view G:

1 CLAMP AS21919WCH12 Item 66

with:

1 SCREW NAS1801-3-21 Item 5

1 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08 Item 9

1 NUT-CLIP NSA5066-3-1 Item 11

7 Install, as shown on view H:

1 CLAMP AS21919WCH09 Item 14

1 CLAMP AS21919WCH10 Item 24

with:

1 SCREW NAS1801-3-9 Item 21

2 WASHER NAS1149C0332R Item 7

1 NUT NAS1291C3M Item 10

8 Install, as shown on view J:

2 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-3-21 Item 5

1 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08 Item 9

1 NUT-CLIP NSA5066-3-1 Item 11

9 Install, as shown on view K:

1 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-08-21 Item 20

1 WASHER NAS1149CN832R Item 23

1 SPACER NSA5527-03-08 Item 9

10 Install, as shown on view L:

1 CLAMP-LOOP,CRS ABS0805-11 Item 67

with:

1 SCREW NAS1801-3-21 Item 5

REV 00 Oct 12/20 A330-27-3237

Page 317
 A330
SERVICE BULLETIN

1 WASHER NSA935808C01 Item 22

1 SPACER NSA5527-03-08D Item 19

1 WASHER NAS1149C0332R Item 7

1 NUT NAS1291C3M Item 10

11 Install and connect the wire, as shown on view M:
- Refer to Ref. Fig. Wiring Diagram - Electrical Harness 5870VB and
Ref. Fig. Hook-up Chart of the Modification of the Wiring in Electrical
Harness 5870VB.
12 Install the Service Bulletin placard identified as SB27–3237, item 74, with
cable ties, item 29, as shown on view M, supplied in:

1 ELECTRICAL F9297001400400
EQUIPMENT
13 Do a continuity test of the new and/or modified electrical wires, refer to
Ref. ESPM 20-52-21.
14 Connect (and lock when relevant) the connectors 1CSK, 1CSD, 1CSH and
58CSR.

REV 00 Oct 12/20 A330-27-3237

Page 318
 A330
SERVICE BULLETIN

CONF 001

Z310

FR91

FR87

FR86

FR85

FR84
FR83
FR80 /82

5870VB /2MF

B C

ICN-A330-A-27XX3237-A-FAPE3-0137I-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137I-A-001-01 SHEET 1/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 319
 A330
SERVICE BULLETIN

CONF 001

TO G
5949VC
5204VC
5205VC

H
F
FR87 58CSR
TO
1CSK
5870VB /2MF

1CSD
L
5393VN /B2
5374VN /DC2

1CSH
FR86 D TO
5212VT TO
5200VP

FR85

ICN-A330-A-27XX3237-A-FAPE3-0137J-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137J-A-003-01 SHEET 2/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 320
 A330
SERVICE BULLETIN

CONF 001

FR87

1CSK

58CSR

5393VN /B2
5870VB /2MF 5374VN /DC2

TO
1CSH

ICN-A330-A-27XX3237-A-FAPE3-0137K-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137K-A-002-01 SHEET 3/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 321
 A330
SERVICE BULLETIN

CONF 001
5

22
26

5870VB /2MF
5
19
22

7
10
25
25

19

19

FR87 D

FR87
5393VN /B2
5374VN /DC2
5870VB /2MF
5 21
7
22

9
18
5870VB /2MF 19 66
7
19 5
10

26 7
10

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0137L-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137L-A-003-01 SHEET 4/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 322
 A330
SERVICE BULLETIN

CONF 001
10

FR87
19

10
7

18

18
67

5870VB /2MF

22
FR87
F 5 5870VB /2MF

10 66
7
5
24
7
5870VB /2MF

9
14 5872VB /2M

7
11
21

G
H

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0137M-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137M-A-001-01 SHEET 5/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 323
 A330
SERVICE BULLETIN

CONF 001
FR87

27

5
7
5870VB /2MF

9
5869VB /1MF

J 27 11

FR87

27

5870VB /2MF

23
5869VB /1MF
20

ICN-A330-A-27XX3237-A-FAPE3-0137N-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137N-A-003-01 SHEET 6/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 324
 A330
SERVICE BULLETIN

CONF 001
FR86

7 19
10

5
22

67

5870VB /2MF

5872VB /2M

FR85

WIRE L
2798-5157 R
2798-5157 B 01
TO
5200VP
5212VT

29
SB27-3237 74

03

5870VB /2MF 02

01

WIRE
2798-6835 R
2798-6835 B
TO
58CSR

M
NOTE: 5872VB /2M
01 INSTALL NEW CABLE TIES, ITEM 29, IF NECESSARY
02 TIGHTEN THE CLAMP IF NECESSARY
03 CUT TO LENGTH ON ASSEMBLY
ICN-A330-A-27XX3237-A-FAPE3-0137O-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137O-A-002-01 SHEET 7/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 325
 A330
SERVICE BULLETIN

CONF 001

BEFORE
FR56 FR80
2MF
H

7 2798-5157 R 15 V11
8 B 14 V12 RVDT 1 MON
9 2798-5158 R 2798-5159 R 12 V21
10 B B 11 V22

2MF FR91
A 3686VC 5205VP
1CS ACTUATOR THS
5949VC A
5870VB
D
B
C
J

AFTER

2MF 2MF
5212VT 7820VB
R 58CS
6
A R 3
F 2798-6835 5
B
B 4 2798-5048 B
G 1 R
FR56 FR80
2MF
H

7 2798-5157 R 2798-6834 R 15 V11

8 B B 14 V12 RVDT 1 MON
9 2798-5158 R 2798-5159 R 12 V21
10 B B 11 V22

2MF FR91
A 3686VC 5205VP
1CS ACTUATOR THS
5949VC A
5870VB
D
NEW WIRE B
NOTE: C
EXISTING WIRE
ONLY WIRES RELATED TO THIS J
SERVICE BULLETIN ARE SHOWN REROUTED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139O-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139O-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5870VB
Page 326
 A330
SERVICE BULLETIN

CONF 001

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 152 3686VC 8 EN3155-014M2018 2798-5157 B 2MF PN24 22980 904,7 310 1CS H 14 EN3155-019F2018 BEFORE

2 152 3686VC 7 EN3155-014M2018 2798-5157 R 2MF PN24 0 0 310 1CS H 15 EN3155-019F2018 BEFORE

3 152 3686VC 8 EN3155-014M2018 2798-5157 B 2MF PN24 22980 904,7 311 5212VT 6G EN3155-016M2018 AFTER

4 152 3686VC 7 EN3155-014M2018 2798-5157 R 2MF PN24 0 0 311 5212VT 6F EN3155-016M2018 AFTER

5 311 5212VT 6B EN3155-016M2018 2798-6835 B 2MF DRB24 5000 196,9 300 58CS R 5 EN3155-019F2018 A

6 311 5212VT 6A EN3155-016M2018 2798-6835 R 2MF DRB24 0 0 300 58CS R 3 EN3155-019F2018 A

7 300 58CS R 4 EN3155-019F2018 2798-6834 B 2MF DRB24 3000 118,1 310 1CS H 14 EN3155-019F2018 A

8 300 58CS R 1 EN3155-019F2018 2798-6834 R 2MF DRB24 0 0 310 1CS H 15 EN3155-019F2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70014 004 00 "SHEET 20,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C0-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5870VB
Page 327
 A330
SERVICE BULLETIN

CONF 002-004
(13) Task A330-A-27-XX-3237-04002-720A-A (A330-A-27-XX-3237-04ZZZ-720Z-A)
Install the Modified Electrical Harness 5870VB V-Prop
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

310 Work location From Frame 85 to Frame 87
Manpower/Resources/Skills

Man-hours 6.00 h
Minimum Number of person 1
Elapsed Time 6.00 h
Skills Electrical
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure

Part kit 273237D02R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
2 ABS0805-15 3 CLAMP
5 NAS1801-3-21 3 SCREW
7 NAS1149C0332R 9 WASHER
8 NSA5527-03-03D 2 SPACER
9 NSA5527-03-08 1 SPACER
10 NAS1291C3M 5 NUT
11 NSA5066-3-1 1 NUT
14 AS21919WCH09 2 CLAMP
16 ABS0805-08 2 CLAMP
18 ABS0805-12 1 CLAMP
19 NSA5527-03-08D 2 SPACER
21 NAS1801-3-9 3 SCREW
22 NSA935808C01 7 WASHER
24 AS21919WCH10 2 CLAMP
26 ABS0805-10 5 CLAMP
46 NAS1801-3-19 3 SCREW
66 AS21919WCH12 2 CLAMP
68 NAS1801-3-10 2 SCREW
70 NAS1801-3-12 2 SCREW
F9297001400400 1 ELECEQPT

REV 00 Oct 12/20 A330-27-3237

Page 328
 A330
SERVICE BULLETIN

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM
Task 20-21-11-911-801
Task 20-28-00-912-810
20-33-00
20-33-42
20-33-44
20-51-20
ESPM
20-52-10
20-52-21
20-54-50
20-56-51
51-40-00
SRM
51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install the fasteners in accordance with Ref. SRM 51-42-00.
4 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
5 If alternative and substitute fasteners have to be used, you must make
sure that the associated nut/collar are compatible in accordance with refer
to Ref. SRM 51-40-00.
6 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
7 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
8 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
9 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
10 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
11 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
12 Adapt the clamp size as necessary, refer to Ref. ESPM 20-33-42.
(b) Install the electrical harness between Frame 85 and Frame 87.
Refer to Ref. Fig. Installation of the Modified Electrical Harness 5870VB at FR87.
Refer to Ref. ESPM 20-33-44 and Ref. AMM Task 20-21-11-911-801 for tightening.
1 Install, as shown on view C:

1 CLAMP AS21919WCH09 Item 14

REV 00 Oct 12/20 A330-27-3237

Page 329
 A330
SERVICE BULLETIN

with:

1 SCREW NAS1801-3-21 Item 5

1 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08 Item 9

1 NUT-CLIP NSA5066-3-1 Item 11

a For the installation of the referenced parts, refer to Ref. Fig.
Installation of the Modified Electrical Harness 5870VB at FR87, SHEET
3, view C.
2 Install, as shown on view D:

2 CLAMP-LOOP,CRS ABS0805-08 Item 16

1 CLAMP AS21919WCH09 Item 14

with:

2 SCREW NAS1801-3-12 Item 70

1 SCREW NAS1801-3-9 Item 21

2 WASHER NSA935808C01 Item 22

1 WASHER NAS1149C0332R Item 7

2 SPACER NSA5527-03-03D Item 8

3 Install, as shown on view E:

3 CLAMP-LOOP,CRS ABS0805-10 Item 26

1 CLAMP-LOOP,CRS ABS0805-12 Item 18

with:

2 SCREW NAS1801-3-21 Item 5

2 WASHER NSA935808C01 Item 22

2 SPACER NSA5527-03-08D Item 19

2 WASHER NAS1149C0332R Item 7

2 NUT NAS1291C3M Item 10

4 At the grounding points 5374VN and 5393VN, as shown on view E, install:

3 BONDING CABLE
with:

2 SCREW NAS1801-3-9 Item 21

2 WASHER NAS1149C0332R Item 7

2 NUT NAS1291C3M Item 10

5 Renew the protective finish with:

Primer Polyurethane 04EAC2

Paint - -
CorrosionInhibiting
Structure

REV 00 Oct 12/20 A330-27-3237

Page 330
 A330
SERVICE BULLETIN

Top Coat Polyurethane - 04JME4

- Grey InternalStructure
6 Install, as shown on view F:

2 CLAMP AS21919WCH10 Item 24

2 CLAMP AS21919WCH12 Item 66

with:

2 SCREW NAS1801-3-10 Item 68

2 WASHER NAS1149C0332R Item 7

7 Install, as shown on view G:

2 CLAMP-LOOP,CRS ABS0805-15 Item 2

1 CLAMP-LOOP,CRS ABS0805-10 Item 26

with:

2 SCREW NAS1801-3-19 Item 46

2 WASHER NSA935808C01 Item 22

1 WASHER NAS1149C0332R Item 7

1 NUT NAS1291C3M Item 10

8 Install, as shown on view H:

1 CLAMP-LOOP,CRS ABS0805-15 Item 2

1 CLAMP-LOOP,CRS ABS0805-10 Item 26

with:

1 SCREW NAS1801-3-19 Item 46

1 WASHER NSA935808C01 Item 22

9 Install the Service Bulletin placard identified as SB27–3237, item 74, with
cable ties, item 29, as shown on view H, supplied in:

1 ELECTRICAL F9297001400400
EQUIPMENT
10 Install and connect the wire, as shown on view J:
- Refer to Ref. Fig. Wiring Diagram - Electrical Harness 5870VB and
Ref. Fig. Hook-up Chart of the Modification of the Wiring in Electrical
Harness 5870VB.
11 Install the Service Bulletin placard identified as SB27–3237, item 74, with
cable ties, item 29, as shown on view J, supplied in:

1 ELECTRICAL F9297001400400
EQUIPMENT
12 Do a continuity test of the new and/or modified electrical wires, refer to
Ref. ESPM 20-52-21.
13 Connect (and lock when relevant) the connectors 1CSK, 1CSD, 1CSH and
58CSR.

REV 00 Oct 12/20 A330-27-3237

Page 331
 A330
SERVICE BULLETIN

CONF 002-004

Z310

FR91

FR87

FR86

FR85
5870VB /2MF
FR84
FR83
FR80 /82

ICN-A330-A-27XX3237-A-FAPE3-0136R-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136R-A-001-01 SHEET 1/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 332
 A330
SERVICE BULLETIN

CONF 002-004

G
J
5212VT

F
H

D
C
5870VB /2MF
FR87 TO
5200VP

58CSR

5393VN /B2
5374VN /DC2
E

TO 1CSH
1CSK
1CSD
FR86

FR85

ICN-A330-A-27XX3237-A-FAPE3-0136S-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136S-A-003-01 SHEET 2/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 333
 A330
SERVICE BULLETIN

CONF 002-004

FR87
11

14
9

5870VB /2MF

7
C 5
5869VB /1MF

FR87

16 5870VB /2MF
8

16 14 7

21

22 D
70

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0136T-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136T-A-003-01 SHEET 3/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 334
 A330
SERVICE BULLETIN

CONF 002-004

FR87
10
7

19

5872VB /2M
18

26
21
7

19
22
5
5374VN /DC2

5393VN /B2 26
10
26

5870VB /2MF

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0136U-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136U-A-001-01 SHEET 4/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 335
 A330
SERVICE BULLETIN

CONF 002-004

66
FR87
5872VB /2M 5870VB /2MF

24
7 68

68 7
24

66

ICN-A330-A-27XX3237-A-FAPE3-0136V-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136V-A-001-01 SHEET 5/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 336
 A330
SERVICE BULLETIN

CONF 002-004

10

5872VB /2M

26

5870VB /2MF

2 2

FR86

22

46

74
G
SB27-3237
2
WIRE 2798-6835
29

5872VB /2M 01

26
01
22
NOTE: H 5870VB /2MF
ELECTRICAL BONDING 46
01 INSTALL NEW CABLE TIES,
ITEM 29, IF NECESSARY
ICN-A330-A-27XX3237-A-FAPE3-0136W-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136W-A-002-01 SHEET 6/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 337
 A330
SERVICE BULLETIN

CONF 002-004

WIRE
2798-6835 R
2798-6835 B
TO WIRE
58CSR 2798-5157 R
2798-5157 B
5212VT TO
5200VP

03

5870VB /2MF

01

STGR8
02

01

29
01

74
FR85
SB27-3237

NOTE:
01 INSTALL NEW CABLE TIES, ITEM 29, IF NECESSARY
02 FASTEN THE CLAMP IF NECESSARY
03 CUT TO LENGTH ON ASSEMBLY
ICN-A330-A-27XX3237-A-FAPE3-0136X-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0136X-A-003-01 SHEET 7/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 338
 A330
SERVICE BULLETIN

CONF 002-004

BEFORE
FR56 FR80
2MF
H

7 2798-5157 R 15 V11
8 B 14 V12 RVDT 1 MON
9 2798-5158 R 2798-5159 R 12 V21
10 B B 11 V22

2MF FR91
A 3686VC 5205VP
1CS ACTUATOR THS
5949VC A
5870VB
D
B
C
J

AFTER

2MF 2MF
5212VT 7820VB
R 58CS
6
A R 3
F 2798-6835 5
B
B 4 2798-5048 B
G 1 R
FR56 FR80
2MF
H

7 2798-5157 R 2798-6834 R 15 V11

8 B B 14 V12 RVDT 1 MON
9 2798-5158 R 2798-5159 R 12 V21
10 B B 11 V22

2MF FR91
A 3686VC 5205VP
1CS ACTUATOR THS
5949VC A
5870VB
D
NEW WIRE B
NOTE: C
EXISTING WIRE
ONLY WIRES RELATED TO THIS J
SERVICE BULLETIN ARE SHOWN REROUTED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139O-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139O-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5870VB
Page 339
 A330
SERVICE BULLETIN

CONF 002-004

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 152 3686VC 8 EN3155-014M2018 2798-5157 B 2MF PN24 22980 904,7 310 1CS H 14 EN3155-019F2018 BEFORE

2 152 3686VC 7 EN3155-014M2018 2798-5157 R 2MF PN24 0 0 310 1CS H 15 EN3155-019F2018 BEFORE

3 152 3686VC 8 EN3155-014M2018 2798-5157 B 2MF PN24 22980 904,7 311 5212VT 6G EN3155-016M2018 AFTER

4 152 3686VC 7 EN3155-014M2018 2798-5157 R 2MF PN24 0 0 311 5212VT 6F EN3155-016M2018 AFTER

5 311 5212VT 6B EN3155-016M2018 2798-6835 B 2MF DRB24 5000 196,9 300 58CS R 5 EN3155-019F2018 A

6 311 5212VT 6A EN3155-016M2018 2798-6835 R 2MF DRB24 0 0 300 58CS R 3 EN3155-019F2018 A

7 300 58CS R 4 EN3155-019F2018 2798-6834 B 2MF DRB24 3000 118,1 310 1CS H 14 EN3155-019F2018 A

8 300 58CS R 1 EN3155-019F2018 2798-6834 R 2MF DRB24 0 0 310 1CS H 15 EN3155-019F2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70014 004 00 "SHEET 20,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C0-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5870VB
Page 340
 A330
SERVICE BULLETIN

CONF 005
(13) Task A330-A-27-XX-3237-04012-720A-A (A330-A-27-XX-3237-04ZZZ-720Z-A)
Install the Modified harness 5870VB Traverse
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 6.00 h
Minimum Number of person 1
Elapsed Time 6.00 h
Skills Electrical
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Primer Polyurethane Paint
04EAC2 - - CorrosionInhibiting
Structure
Top Coat Polyurethane - -
04JME4
Grey InternalStructure

Part kit 273237D01R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F9297001400400 1 ELECEQPT

Part kit 273237D07R03

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
5 NAS1801-3-21 10 SCREW
7 NAS1149C0332R 11 WASHER
9 NSA5527-03-08 3 SPACER
10 NAS1291C3M 8 NUT
11 NSA5066-3-1 1 NUT
14 AS21919WCH09 1 CLAMP
18 ABS0805-12 3 CLAMP
19 NSA5527-03-08D 8 SPACER
20 NAS1801-08-21 1 SCREW
21 NAS1801-3-9 3 SCREW
22 NSA935808C01 8 WASHER
23 NAS1149CN832R 1 WASHER
24 AS21919WCH10 1 CLAMP
25 ABS0805-09 2 CLAMP
26 ABS0805-10 2 CLAMP
27 AS21919WCH08 1 CLAMP
66 AS21919WCH12 2 CLAMP
67 ABS0805-11 2 CLAMP

REV 00 Oct 12/20 A330-27-3237

Page 341
 A330
SERVICE BULLETIN

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM
Task 20-21-11-911-801
Task 20-28-00-912-810
20-33-00
20-33-42
20-33-44
20-51-20
ESPM
20-52-10
20-52-21
20-54-50
20-56-51
51-40-00
SRM
51-42-00
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 Remove and install the fasteners in accordance with Ref. SRM 51-42-00.
4 For the electrical bonding, refer to Ref. ESPM 20-51-20 and Ref. AMM Task
20-28-00-912-810.
5 If alternative and substitute fasteners have to be used, you must make
sure that the associated nut/collar are compatible in accordance with refer
to Ref. SRM 51-40-00.
6 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
7 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
8 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
9 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
10 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
11 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
12 Adapt the clamp size as necessary, refer to Ref. ESPM 20-33-42.
(b) Install the electrical harness between Frame 85 and Frame 87.
Refer to Ref. Fig. Installation of the Modified Electrical Harness 5870VB at FR87.
Refer to Ref. ESPM 20-33-44 and Ref. AMM Task 20-21-11-911-801 for tightening.
1 Install, as shown on view D:

2 CLAMP-LOOP,CRS ABS0805-09 Item 25

REV 00 Oct 12/20 A330-27-3237

Page 342
 A330
SERVICE BULLETIN

1 CLAMP-LOOP,CRS ABS0805-10 Item 26

with:

3 SCREW NAS1801-3-21 Item 5

3 WASHER NSA935808C01 Item 22

3 SPACER NSA5527-03-08D Item 19

1 WASHER NAS1149C0332R Item 7

1 NUT NAS1291C3M Item 10

2 Install, as shown on view E:

1 CLAMP-LOOP,CRS ABS0805-10 Item 26

1 CLAMP-LOOP,CRS ABS0805-12 Item 18

1 CLAMP AS21919WCH12 Item 66

with:

3 SCREW NAS1801-3-21 Item 5

2 WASHER NSA935808C01 Item 22

2 WASHER NAS1149C0332R Item 7

2 SPACER NSA5527-03-08D Item 19

1 SPACER NSA5527-03-08 Item 9

1 NUT NAS1291C3M Item 10

3 At the grounding points 5374VN and 5393VN, as shown on view E, install:

3 BONDING ANGLE
with:

2 SCREW NAS1801-3-9 Item 21

2 WASHER NAS1149C0332R Item 7

2 NUT NAS1291C3M Item 10

4 Renew the protective finish with:

Primer Polyurethane 04EAC2

Paint - -
CorrosionInhibiting
Structure

Top Coat Polyurethane - 04JME4

- Grey InternalStructure
5 Install, as shown on view F:

2 CLAMP-LOOP,CRS ABS0805-12 Item 18

1 CLAMP-LOOP,CRS ABS0805-11 Item 67

with:

2 SCREW NAS1801-3-21 Item 5

REV 00 Oct 12/20 A330-27-3237

Page 343
 A330
SERVICE BULLETIN

2 WASHER NSA935808C01 Item 22

2 WASHER NAS1149C0332R Item 7

2 SPACER NSA5527-03-08D Item 19

2 NUT NAS1291C3M Item 10

6 Install, as shown on view G:

1 CLAMP AS21919WCH12 Item 66

with:

1 SCREW NAS1801-3-21 Item 5

1 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08 Item 9

1 NUT-CLIP NSA5066-3-1 Item 11

7 Install, as shown on view H:

1 CLAMP AS21919WCH09 Item 14

1 CLAMP AS21919WCH10 Item 24

with:

1 SCREW NAS1801-3-9 Item 21

2 WASHER NAS1149C0332R Item 7

1 NUT NAS1291C3M Item 10

8 Install, as shown on view J:

2 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-3-21 Item 5

1 WASHER NAS1149C0332R Item 7

1 SPACER NSA5527-03-08 Item 9

1 NUT-CLIP NSA5066-3-1 Item 11

9 Install, as shown on view K:

1 CLAMP AS21919WCH08 Item 27

with:

1 SCREW NAS1801-08-21 Item 20

1 WASHER NAS1149CN832R Item 23

1 SPACER NSA5527-03-08 Item 9

10 Install, as shown on view L:

1 CLAMP-LOOP,CRS ABS0805-11 Item 67

with:

1 SCREW NAS1801-3-21 Item 5

REV 00 Oct 12/20 A330-27-3237

Page 344
 A330
SERVICE BULLETIN

1 WASHER NSA935808C01 Item 22

1 SPACER NSA5527-03-08D Item 19

1 WASHER NAS1149C0332R Item 7

1 NUT NAS1291C3M Item 10

11 Install and connect the wire, as shown on view M:
- Refer to Ref. Fig. Wiring Diagram - Electrical Harness 5870VB and
Ref. Fig. Hook-up Chart of the Modification of the Wiring in Electrical
Harness 5870VB.
12 Install the Service Bulletin placard identified as SB27–3237, item 74, with
cable ties, item 29, as shown on view M, supplied in:

1 ELECTRICAL F9297001400400
EQUIPMENT
13 Do a continuity test of the new and/or modified electrical wires, refer to
Ref. ESPM 20-52-21.
14 Connect (and lock when relevant) the connectors 1CSK, 1CSD, 1CSH and
58CSR.

REV 00 Oct 12/20 A330-27-3237

Page 345
 A330
SERVICE BULLETIN

CONF 005

Z310

FR91

FR87

FR86

FR85

FR84
FR83
FR80 /82

5870VB /2MF

B C

ICN-A330-A-27XX3237-A-FAPE3-0137I-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137I-A-001-01 SHEET 1/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 346
 A330
SERVICE BULLETIN

CONF 005

TO G
5949VC
5204VC
5205VC

H
F
FR87 58CSR
TO
1CSK
5870VB /2MF

1CSD
L
5393VN /B2
5374VN /DC2

1CSH
FR86 D TO
5212VT TO
5200VP

FR85

ICN-A330-A-27XX3237-A-FAPE3-0137J-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137J-A-003-01 SHEET 2/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 347
 A330
SERVICE BULLETIN

CONF 005

FR87

1CSK

58CSR

5393VN /B2
5870VB /2MF 5374VN /DC2

TO
1CSH

ICN-A330-A-27XX3237-A-FAPE3-0137K-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137K-A-002-01 SHEET 3/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 348
 A330
SERVICE BULLETIN

CONF 005
5

22
26

5870VB /2MF
5
19
22

7
10
25
25

19

19

FR87 D

FR87
5393VN /B2
5374VN /DC2
5870VB /2MF
5 21
7
22

9
18
5870VB /2MF 19 66
7
19 5
10

26 7
10

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0137L-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137L-A-003-01 SHEET 4/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 349
 A330
SERVICE BULLETIN

CONF 005
10

FR87
19

10
7

18

18
67

5870VB /2MF

22
FR87
F 5 5870VB /2MF

10 66
7
5
24
7
5870VB /2MF

9
14 5872VB /2M

7
11
21

G
H

NOTE:
ELECTRICAL BONDING
ICN-A330-A-27XX3237-A-FAPE3-0137M-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137M-A-001-01 SHEET 5/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 350
 A330
SERVICE BULLETIN

CONF 005
FR87

27

5
7
5870VB /2MF

9
5869VB /1MF

J 27 11

FR87

27

5870VB /2MF

23
5869VB /1MF
20

ICN-A330-A-27XX3237-A-FAPE3-0137N-A-003-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137N-A-003-01 SHEET 6/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 351
 A330
SERVICE BULLETIN

CONF 005
FR86

7 19
10

5
22

67

5870VB /2MF

5872VB /2M

FR85

WIRE L
2798-5157 R
2798-5157 B 01
TO
5200VP
5212VT

29
SB27-3237 74

03

5870VB /2MF 02

01

WIRE
2798-6835 R
2798-6835 B
TO
58CSR

M
NOTE: 5872VB /2M
01 INSTALL NEW CABLE TIES, ITEM 29, IF NECESSARY
02 TIGHTEN THE CLAMP IF NECESSARY
03 CUT TO LENGTH ON ASSEMBLY
ICN-A330-A-27XX3237-A-FAPE3-0137O-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0137O-A-002-01 SHEET 7/7

REV 00 Oct 12/20 A330-27-3237
Installation of the Modified Electrical Harness 5870VB at FR87
Page 352
 A330
SERVICE BULLETIN

CONF 005

BEFORE
FR56 FR80
2MF
H

7 2798-5157 R 15 V11
8 B 14 V12 RVDT 1 MON
9 2798-5158 R 2798-5159 R 12 V21
10 B B 11 V22

2MF FR91
A 3686VC 5205VP
1CS ACTUATOR THS
5949VC A
5870VB
D
B
C
J

AFTER

2MF 2MF
5212VT 7820VB
R 58CS
6
A R 3
F 2798-6835 5
B
B 4 2798-5048 B
G 1 R
FR56 FR80
2MF
H

7 2798-5157 R 2798-6834 R 15 V11

8 B B 14 V12 RVDT 1 MON
9 2798-5158 R 2798-5159 R 12 V21
10 B B 11 V22

2MF FR91
A 3686VC 5205VP
1CS ACTUATOR THS
5949VC A
5870VB
D
NEW WIRE B
NOTE: C
EXISTING WIRE
ONLY WIRES RELATED TO THIS J
SERVICE BULLETIN ARE SHOWN REROUTED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139O-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139O-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5870VB
Page 353
 A330
SERVICE BULLETIN

CONF 005

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 152 3686VC 8 EN3155-014M2018 2798-5157 B 2MF PN24 22980 904,7 310 1CS H 14 EN3155-019F2018 BEFORE

2 152 3686VC 7 EN3155-014M2018 2798-5157 R 2MF PN24 0 0 310 1CS H 15 EN3155-019F2018 BEFORE

3 152 3686VC 8 EN3155-014M2018 2798-5157 B 2MF PN24 22980 904,7 311 5212VT 6G EN3155-016M2018 AFTER

4 152 3686VC 7 EN3155-014M2018 2798-5157 R 2MF PN24 0 0 311 5212VT 6F EN3155-016M2018 AFTER

5 311 5212VT 6B EN3155-016M2018 2798-6835 B 2MF DRB24 5000 196,9 300 58CS R 5 EN3155-019F2018 A

6 311 5212VT 6A EN3155-016M2018 2798-6835 R 2MF DRB24 0 0 300 58CS R 3 EN3155-019F2018 A

7 300 58CS R 4 EN3155-019F2018 2798-6834 B 2MF DRB24 3000 118,1 310 1CS H 14 EN3155-019F2018 A

8 300 58CS R 1 EN3155-019F2018 2798-6834 R 2MF DRB24 0 0 310 1CS H 15 EN3155-019F2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70014 004 00 "SHEET 20,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C0-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5870VB
Page 354
 A330
SERVICE BULLETIN

CONF 001
(14) Task A330-A-27-XX-3237-04001-760A-A (A330-A-27-XX-3237-04ZZZ-760Z-A)
Reroute the reidentified wire 2499-5020 to 5000VE
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

170
160
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical
Material necessary to do the job
Part kit 273237D05R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
177 EN3155-018M1616 1 PIN
E0397FY2000 1 CONTACT

Part kit 273237D09R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F9297001300600 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
06-41-53, Page Block 001
20-33-44
20-52-10
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.

REV 00 Oct 12/20 A330-27-3237

Page 355
 A330
SERVICE BULLETIN

5 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
6 Tag all the parts you must remove and retain to make the subsequent
installation easier.
7 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
8 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
9 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
10 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
(b) Disconnect the connector FIN 5112VCA from the Electrical Panel 5000VE.
(c) Remove, refer to Ref. Fig. Rerouting and Reidentification of the wire 2499-5020 to
5000VE.

1 CONNECTOR-PLUG Item (178) Retain

1 BACKSHELL- Item (179) Retain

CONNECTOR
use:

1 CONTACT-BLIND E0397FY2000
(d) Route the wire 2798-6836 on the existing wire bundle and cut to the correct
length, refer to Ref. Fig. Rerouting and Reidentification of the wire 2499-5020 to
5000VE, view B
Refer to Ref. Fig. Wiring Diagram - Electrical Harness 5871VB and Ref. Fig. Hook-
up Chart of the Modification of the Wiring in Electrical Harness 5869VB.
(e) Install:

1 PIN-CONTACT EN3155-018M1616 Item 177

(f) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.
(g) On the existing wire 2798-6836, install the sleeve identified as 2798-6836, item
180, refer to Ref. ESPM 20-56-51 and Ref. ESPM 20-33-44, supplied in:

1 ELECTRICAL F9297001300600
EQUIPMENT

NOTE: Shrink the wire-identification sleeve to cover the existing wire.

(h) Install the Service Bulletin identification placard, item 74, with cable ties, item
29, as shown on view B, supplied in:

1 ELECTRICAL F9297001300600
EQUIPMENT
(i) Install, as shown on view B:

1 CONNECTOR-PLUG Item (178) Retained

1 BACKSHELL- Item (179) Retained

CONNECTOR

REV 00 Oct 12/20 A330-27-3237

Page 356
 A330
SERVICE BULLETIN

(j) Connect (and lock if relevant) the connectors FIN 5112VCA.

REV 00 Oct 12/20 A330-27-3237

Page 357
 A330
SERVICE BULLETIN

CONF 001

Z170
Z160

5869VB

5205VP

01 02

B
5000VE

5871VB FR69

A
NOTE:
01 REIDENTIFY WIRE 2499-5020 INTO 2798-6836 USE PINK SLEEVE, ITEM 180.
MAKE SURE TO COVER ALL EXISTING WIRE NUMBERS IN THIS AREA
02 ATTACH TO EXISTING ELECTRICAL HARNESS 5871VB WITH CABLE TIES,
AS NECESSARY ICN-A330-A-27XX3237-A-FAPE3-0139S-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139S-A-002-01 SHEET 1/2

REV 00 Oct 12/20 Rerouting and Reidentification of A330-27-3237
the wire 2499-5020 to 5000VE Page 358
 A330
SERVICE BULLETIN

CONF 001

5000VE

PIN -A

03
177

(29)
29
5112VC
2499-5020 (BEFORE) (178)
2798-6836 (AFTER) 29
5112VCA
180
29

(179)

74

SB27-3237

NOTE:
03 CUT TO LENGHT ON ASSEMBLY
ICN-A330-A-27XX3237-A-FAPE3-0139T-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139T-A-001-01 SHEET 2/2

REV 00 Oct 12/20 Rerouting and Reidentification of A330-27-3237
the wire 2499-5020 to 5000VE Page 359
 A330
SERVICE BULLETIN

CONF 001

BEFORE
5871VB 5871VB
FR56 FR80 FR86 FR91

1M 1M

16 2499-5020-DR20 2499-5020-DR20 G

A 3671VC 01 5123VC A
5205VP

AFTER
FR69

4
-A

5112VC A
5869VB 5871VB
5213VT
FR56 FR80 FR86 FR91

1MF 1M

16 2798-6836-DR20 2499-5020-DR20 G

A 3671VC 5123VC A
5205VP

NOTE: NOTE:
EXISTING WIRE
ONLY WIRES RELATED TO THIS 01 CUT THE WIRE CLOSE TO THE BEGINNING OF THE LIGHTNING PROTECTION HOSE
SERVICE BULLETIN ARE SHOWN REROUTED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139L-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139L-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5871VB
Page 360
 A330
SERVICE BULLETIN

CONF 001

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 21650 852,4 311 - - - BEFORE (5871VB)

5 150 5112VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 20000 787,4 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF PN24 3480 137,0 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF PN24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 006 00 "SHEET 33,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-0135K-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 361
 A330
SERVICE BULLETIN

CONF 002-004
(14) Task A330-A-27-XX-3237-04005-760A-A (A330-A-27-XX-3237-04ZZZ-760Z-A)
Reroute the reidentified wire 2499-5020 to 5000VE
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

170
160
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical
Material necessary to do the job
Part kit 273237D02R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F9297001300700 1 ELECEQPT

Part kit 273237D05R02

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
177 EN3155-018M1616 1 PIN
E0397FY2000 1 CONTACT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
06-41-53, Page Block 001
20-33-44
20-52-10
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.

REV 00 Oct 12/20 A330-27-3237

Page 362
 A330
SERVICE BULLETIN

5 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
6 Tag all the parts you must remove and retain to make the subsequent
installation easier.
7 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
8 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
9 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
10 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
(b) Disconnect the connector FIN 5112VCA from the Electrical Panel 5000VE.
(c) Remove, refer to Ref. Fig. Rerouting and Reidentification of the wire 2499-5020 to
5000VE.

1 CONNECTOR-PLUG Item (178) Retain

1 BACKSHELL- Item (179) Retain

CONNECTOR
use:

1 CONTACT-BLIND E0397FY2000
(d) Route the wire 2798-6836 on the existing wire bundle and cut to the correct
length, refer to Ref. Fig. Rerouting and Reidentification of the wire 2499-5020 to
5000VE, view B
Refer to Ref. Fig. Wiring Diagram - Electrical Harness 5871VB and Ref. Fig. Hook-
up Chart of the Modification of the Wiring in Electrical Harness 5869VB.
(e) Install:

1 PIN-CONTACT EN3155-018M1616 Item 177

(f) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.
(g) On the existing wire 2798-6836, install the sleeve identified as 2798-6836, item
180, refer to Ref. ESPM 20-56-51 and Ref. ESPM 20-33-44, supplied in:

1 ELECTRICAL F9297001300700
EQUIPMENT

NOTE: Shrink the wire-identification sleeve to cover the existing wire.

(h) Install the Service Bulletin identification placard, item 74, with cable ties, item
29, as shown on view B, supplied in:

1 ELECTRICAL F9297001300700
EQUIPMENT
(i) Install, as shown on view B:

1 CONNECTOR-PLUG Item (178) Retained

1 BACKSHELL- Item (179) Retained

CONNECTOR

REV 00 Oct 12/20 A330-27-3237

Page 363
 A330
SERVICE BULLETIN

(j) Connect (and lock if relevant) the connectors FIN 5112VCA.

REV 00 Oct 12/20 A330-27-3237

Page 364
 A330
SERVICE BULLETIN

CONF 002-004

Z170
Z160

5869VB

5205VP

01 02

B
5000VE

5871VB FR69

A
NOTE:
01 REIDENTIFY WIRE 2499-5020 INTO 2798-6836 USE PINK SLEEVE, ITEM 180.
MAKE SURE TO COVER ALL EXISTING WIRE NUMBERS IN THIS AREA
02 ATTACH TO EXISTING ELECTRICAL HARNESS 5871VB WITH CABLE TIES,
AS NECESSARY ICN-A330-A-27XX3237-A-FAPE3-0139S-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139S-A-002-01 SHEET 1/2

REV 00 Oct 12/20 Rerouting and Reidentification of A330-27-3237
the wire 2499-5020 to 5000VE Page 365
 A330
SERVICE BULLETIN

CONF 002-004

5000VE

PIN -A

03
177

(29)
29
5112VC
2499-5020 (BEFORE) (178)
2798-6836 (AFTER) 29
5112VCA
180
29

(179)

74

SB27-3237

NOTE:
03 CUT TO LENGHT ON ASSEMBLY
ICN-A330-A-27XX3237-A-FAPE3-0139T-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139T-A-001-01 SHEET 2/2

REV 00 Oct 12/20 Rerouting and Reidentification of A330-27-3237
the wire 2499-5020 to 5000VE Page 366
 A330
SERVICE BULLETIN

CONF 002-004

BEFORE
5871VB 5871VB
FR56 FR80 FR86 FR91

1M 1M

16 2499-5020-DR20 2499-5020-DR20 G

A 3671VC 01 5123VC A
5205VP

AFTER
FR69

4
-A

5112VC A
5869VB 5871VB
5213VT
FR56 FR80 FR86 FR91

1MF 1M

16 2798-6836-DR20 2499-5020-DR20 G

A 3671VC 5123VC A
5205VP

NOTE: NOTE:
EXISTING WIRE
ONLY WIRES RELATED TO THIS 01 CUT THE WIRE CLOSE TO THE BEGINNING OF THE LIGHTNING PROTECTION HOSE
SERVICE BULLETIN ARE SHOWN REROUTED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139L-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139L-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5871VB
Page 367
 A330
SERVICE BULLETIN

CONF 002-004

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 21650 852,4 311 - - - BEFORE (5871VB)

5 150 5112VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 20000 787,4 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF PF24 3340 131,5 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF PF24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 007 00 "SHEET 34,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C3-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 368
 A330
SERVICE BULLETIN

CONF 005
(14) Task A330-A-27-XX-3237-04014-760A-A (A330-A-27-XX-3237-04ZZZ-760Z-A)
Reroute the reidentified wire 2499-5020 to 5000VE
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location

170
160
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical
Material necessary to do the job
Part kit 273237D06R04
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
177 EN3155-018M1616 1 PIN
E0397FY2000 1 CONTACT

Part kit 273237D07R03

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F9297001300800 1 ELECEQPT
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
06-41-53, Page Block 001
20-33-44
20-52-10
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices given in this procedure:
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.

REV 00 Oct 12/20 A330-27-3237

Page 369
 A330
SERVICE BULLETIN

5 Install the MOD/SB placards in a visible position at each end and equally
(approximately every 2.00 m (80.000 in.)) along the length of the new or
modified wires.
6 Tag all the parts you must remove and retain to make the subsequent
installation easier.
7 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
8 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
9 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
10 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
(b) Disconnect the connector FIN 5051VCA from the Electrical Panel 5000VE.
(c) Remove, refer to Ref. Fig. Rerouting and Reidentification of the wire 2499-5020 to
5000VE.

1 CONNECTOR-PLUG Item (178) Retain

1 BACKSHELL- Item (179) Retain

CONNECTOR
use:

1 CONTACT-BLIND E0397FY2000
(d) Route the wire 2798-6836 on the existing wire bundle and cut to the correct
length, refer to Ref. Fig. Rerouting and Reidentification of the wire 2499-5020 to
5000VE, view B.
Refer to Ref. Fig. Wiring Diagram - Electrical Harness 5871VB and Ref. Fig. Hook-
up Chart of the Modification of the Wiring in Electrical Harness 5869VB.
(e) Install:

1 PIN-CONTACT EN3155-018M1616 Item 177

(f) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.
(g) On the existing wire 2798-6836, install the sleeve identified as 2798-6836, item
180, refer to Ref. ESPM 20-56-51 and Ref. ESPM 20-33-44, supplied in:

1 ELECTRICAL F9297001300800
EQUIPMENT

NOTE: Shrink the wire-identification sleeve to cover the existing wire.

(h) Install the Service Bulletin identification placard, item 74, with cable ties, item
29, as shown on view B, supplied in:

1 ELECTRICAL F9297001300800
EQUIPMENT
(i) Install, as shown on view B:

1 CONNECTOR-PLUG Item (178) Retained

1 BACKSHELL- Item (179) Retained

CONNECTOR

REV 00 Oct 12/20 A330-27-3237

Page 370
 A330
SERVICE BULLETIN

(j) Connect (and lock if relevant) the connectors FIN 5051VCA.

REV 00 Oct 12/20 A330-27-3237

Page 371
 A330
SERVICE BULLETIN

CONF 005

Z170
Z160

5869VB

5205VP

01 02

B
5000VE

5871VB FR69

NOTE:
01 REIDENTIFY WIRE 2499-5020 INTO 2798-6836 USE PINK SLEEVE, ITEM 180
MAKE SURE TO COVER ALL EXISTING WIRE NUMBERS IN THIS AREA
02 ATTACH TO EXISTING ELECTRICAL HARNESS 5871VB WITH CABLE TIES,
AS NECESSARY ICN-A330-A-27XX3237-A-FAPE3-0139U-A-002-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139U-A-002-01 SHEET 1/2

REV 00 Oct 12/20 Rerouting and Reidentification of A330-27-3237
the wire 2499-5020 to 5000VE Page 372
 A330
SERVICE BULLETIN

CONF 005

5000VE

PIN -A

03
177

(29)
29
5051VC
2499-5020 (BEFORE)
2798-6836 (AFTER) 29 (178)
5051VCA
180
29

(179)

SB27-3237

NOTE:
03 CUT TO LENGHT ON ASSEMBLY
ICN-A330-A-27XX3237-A-FAPE3-0139V-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139V-A-001-01 SHEET 2/2

REV 00 Oct 12/20 Rerouting and Reidentification of A330-27-3237
the wire 2499-5020 to 5000VE Page 373
 A330
SERVICE BULLETIN

CONF 005

BEFORE
5871VB 5871VB
FR56 FR80 FR86 FR91

1M 1M

16 2499-5020-DR20 2499-5020-DR20 G

A 3671VC 01 5123VC A
5205VP

AFTER
FR69

4
-A

5051VC A
5869VB 5871VB
5213VT
FR56 FR80 FR86 FR91

1MF 1M

16 2798-6836-DR20 2499-5020-DR20 G

A 3671VC 5123VC A
5205VP

NOTE: NOTE:
EXISTING WIRE
ONLY WIRES RELATED TO THIS 01 CUT THE WIRE CLOSE TO THE BEGINNING OF THE LIGHTNING PROTECTION HOSE
SERVICE BULLETIN ARE SHOWN REROUTED WIRE
ICN-A330-A-27XX3237-A-FAPE3-0139M-A-001-01

Figure ICN-A330-A-27XX3237-A-FAPE3-0139M-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Wiring Diagram - Electrical Harness 5871VB
Page 374
 A330
SERVICE BULLETIN

CONF 005

L
END 1 LEAD END 2
I INSTRUCTIONS
N LENGTH
E ZONE OR ELEC. WIRE ZONE OR ELEC.
TERM. TERMINAL P/N C0L ROUTE GAUGE TERM. TERMINAL P/N
PANEL IDENT. IDENT MM INCH PANEL IDENT

1 310 6326VN25 DC1 NSA936501TA1604 2798-5045 - 1MF DR18 3000 118,1 300 58CS S 2 EN3155-019F2018 A

2 311 5213VT 4D EN3155-016M2018 2798-5046 - 1MF DR18 5000 196,9 300 58CS S 1 EN3155-019F2018 A

3 310 6327VN25 B1 NSA936501TA1604 2798-5047 - 1MF DR18 3000 118,1 300 58CS S 3 EN3155-019F2018 A

4 151 3671VC 16 EN3155-014M2018 2499-5020 - 1M DR20 19400 763,8 311 - - - BEFORE (5871VB)

5 150 5051VC A -A EN3155-018M1616 2798-6836 - 1MF DR20 19400 763,8 311 5213VT 4E EN3155-016M2018 AFTER

6 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 3440 135,4 311 5213VT 1E EN3155-016M2018 D

7 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 D

8 310 1CS G 1 EN3155-019F2018 2798-5041 B 1MF DRB24 5000 196,9 311 5213VT 1E EN3155-016M2018 A

9 310 1CS G 2 EN3155-019F2018 2798-5041 R 1MF DRB24 0 0 311 5213VT 2E EN3155-016M2018 A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25
ELT.EQUIPMENT F929 70013 008 00 "SHEET 35,ISSUE C" A = ADDED WIRE

D = DELETED WIRE

Figure ICN-A330-A-27XX3237-A-FAPE3-013C4-A-001-01 SHEET 1/1

REV 00 Oct 12/20 A330-27-3237
Hook-up Chart of the Modification of the Wiring in Electrical Harness 5869VB
Page 375
 A330
SERVICE BULLETIN

CONF ALL
D. PREPARATION FOR TEST
(1) Task A330-A-27-XX-3237-02001-761A-A (A330-A-27-XX-3237-02ZZZ-761Z-A)
Preparation for Test
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 24-41-00-861-801
Procedure
(a) Job Set-up:
1 In the cockpit, on the ELEC control panel 235VU, push these pushbutton
switches:
- GEN1,GEN2
- APU GEN (only if the aircraft is energized from the external power).
2 Remove the warning notices.
3 Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-00-
861-801

NOTE: If the aircraft is energized from the external power, make sure that
the pushbutton switches BAT 1, BAT 2, APU BAT and EXT A (B) are
pushed.

NOTE: If the aircraft is energized from the APU, make sure that the
pushbutton switches BAT 1, BAT 2, APU BAT and APU GEN are
pushed.

4 Remove the safety clip(s) and/or tag(s) and close/unlock this (these) circuit
breaker(s):

PANEL DESIGNATION FIN LOCATION SEE NOTES

701PP 10PB1 (1) (2)
702PP 10PB2 (1) (3)
NOTE(S)
(1): For circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-801.
(2): The circuit breaker FIN 10PB1 is located on panel 742VU at position 72S.
(3): The circuit breaker FIN 10PB2 is located on panel 742VU at position 71S.
E. TEST
(1) Task A330-A-27-XX-3237-01001-343A-A (A330-A-27-XX-3237-01ZZZ-343Z-A)
Preliminary Test

REV 00 Oct 12/20 A330-27-3237

Page 376
 A330
SERVICE BULLETIN

Job Set-Up Information

Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 21-26-00-710-803
Task 22-97-00-740-801
Task 31-50-00-710-803
AMM
Task 31-50-00-740-801
Task 31-60-00-710-802
Task 33-14-00-710-801
Procedure
(a) Preliminary Test

NOTE: If the aircraft is operated in actual CAT3 conditions, you must also do the
LAND CAT3 capability test, refer to Ref. AMM Task 22-97-00-740-801.

1 Do the operational test of the instrument and panel integral lighting, refer
to Ref. AMM Task 33-14-00-710-801.
2 Do the operational test of the avionics-equipment ventilation system, refer
to Ref. AMM Task 21-26-00-710-803.
3 Do the operational test of the ECAM control panel, refer to Ref. AMM Task
31-50-00-710-803.
4 Do the test of the Flight Warning System (FWS), Ref. AMM Task 31-50-00-
740-801
5 Do the operational test of the Electronic Instrument System (EIS), refer to
Ref. AMM Task 31-60-00-710-802
(2) Task A330-A-27-XX-3237-01001-345A-A (A330-A-27-XX-3237-01ZZZ-345Z-A)
Test
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Skills Electrical

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 27-44-51-400-801
Procedure
(a) Test

REV 00 Oct 12/20 A330-27-3237

Page 377
 A330
SERVICE BULLETIN

1 Do the test procedure as specified in installation of the THS actuator, refer

to Ref. AMM Task 27-44-51-400-801.
F. CLOSE-UP
(1) Task A330-A-27-XX-3237-01001-740A-A (A330-A-27-XX-3237-01ZZZ-740Z-A)
Close-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 3.00 h
Minimum Number of person 1
Elapsed Time 3.00 h

Referenced Information

Manuals/Drawings References/Sheets
Task 24-41-00-862-801
Task 25-53-00-400-801
AMM Task 25-54-00-400-801
Task 52-30-00-410-803
52-41-00, Page Block 001
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Remove the warning notices.
(c) Install the AFT cargo ceiling panels (Panel 151FC, Panel 151HC, Panel 151KC and
Panel 151PC) from the AFT cargo compartment, refer to Ref. AMM Task 25-53-00-
400-801.
(d) Install the ceiling panels (Panel 161DC, Panel 161EC and Panel 161FC) from the
bulk cargo compartment, refer to Ref. AMM Task 25-54-00-400-801.
(e) Install the sidewall panels (Panel 162RW and Panel 162KW) in the bulk cargo
compartment, refer to Ref. AMM Task 25-54-00-400-801.
(f) Close the maintenance door 312AR, refer to Ref. AMM 52-41-00, Page Block 001.
(g) Close the bulk cargo-compartment door 823, refer to Ref. AMM Task 52-30-00-
410-803.
(h) De-energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-00-862-
801.
(i) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A330-A-27-XX-3237-01001-90AA-A (A330-A-27-XX-3237-01ZZZ-90AZ-A)
Administrative

Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

REV 00 Oct 12/20 A330-27-3237

Page 378
 A330
SERVICE BULLETIN
APPENDIX
APPENDIX
A. REPORTING SHEET

TITLE: FLIGHT CONTROLS - TRIMMABLE HORIZONTAL STABILIZER (THS)

HYDRAULIC ACTUATION - INTRODUCE WIRING PROVISION FOR LOAD
SENSING DEVICE (LSD) RETROFIT

MODIFICATION No.: 208458S34974 208459S34991

(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:

- For complete information on reporting means to Airbus, Question 2 "What are

the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"

NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

REV 00 Oct 12/20 A330-27-3237

Page 379
 A330
SERVICE BULLETIN
APPENDIX
B. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.

Quality rating of this SB 4 3 2 1

Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y/N

NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score

If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.

Planning Material Instructions

X Applicability X Tooling X Preparation
X Reason X List of Materials X Mod/Inspection
Operator Supplied
X Manpower X Kit content X Test
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support

Comments :

Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.

REV 00 Oct 12/20 A330-27-3237

Page 380