P9hak 950

Power Systems
Adapters for the 9040-MR9
IBM
Note
Before using this information and the product it supports, read the information in “Safety notices” on
page v, “Notices” on page 67, the IBM Systems Safety Notices manual, G229-9054, and the IBM
Environmental Notices and User Guide, Z125–5823.
This edition applies to IBM® Power Systems servers that contain the POWER9™ processor and to all associated models.
© Copyright International Business Machines Corporation 2018, 2021.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with
IBM Corp.
Contents
Safety notices........................................................................................................v
Installing, removing, and replacing adapters..........................................................1

Installing adapters....................................................................................................................................... 1
Preparing the system..............................................................................................................................1
Installing an adapter.............................................................................................................................. 9
Preparing the system for operation..................................................................................................... 15
Removing and replacing an adapter..........................................................................................................18
Preparing the system........................................................................................................................... 18
Removing an adapter........................................................................................................................... 27
Replacing an adapter............................................................................................................................30
Permanently removing an adapter from the system................................................................................ 38
Preparing the system........................................................................................................................... 38
Permanently removing an adapter.......................................................................................................43
Related procedures for installing and removing adapters........................................................................49
Avoiding electric shock........................................................................................................................ 49
Handling static-sensitive devices........................................................................................................ 50
Updating the worldwide port name..................................................................................................... 51
Removing and replacing the tailstock on an adapter ......................................................................... 51
Hot-plug manager access for AIX........................................................................................................ 56
Installing the AIX device driver software............................................................................................ 59
Installing or replacing an adapter with the system power turned on in a Virtual I/O Server.............60
Verifying that the hot-plug adapter tools are installed for the Linux operating system.....................63
Checking the amount of remaining life in NVMe devices.................................................................... 64
Notices................................................................................................................67
Accessibility features for IBM Power Systems servers............................................................................ 68
Privacy policy considerations ................................................................................................................... 69
Trademarks................................................................................................................................................ 69
Electronic emission notices.......................................................................................................................69
Class A Notices..................................................................................................................................... 69
Class B Notices..................................................................................................................................... 73
Terms and conditions.................................................................................................................................75
iii
iv
Safety notices
Safety notices may be printed throughout this guide:
• DANGER notices call attention to a situation that is potentially lethal or extremely hazardous to people.
• CAUTION notices call attention to a situation that is potentially hazardous to people because of some
existing condition.
• Attention notices call attention to the possibility of damage to a program, device, system, or data.
World Trade safety information

Several countries require the safety information contained in product publications to be presented in
their national languages. If this requirement applies to your country, safety information documentation is
included in the publications package (such as in printed documentation, on DVD, or as part of the product)
shipped with the product. The documentation contains the safety information in your national language
with references to the U.S. English source. Before using a U.S. English publication to install, operate, or
service this product, you must first become familiar with the related safety information documentation.
You should also refer to the safety information documentation any time you do not clearly understand any
safety information in the U.S. English publications.
Replacement or additional copies of safety information documentation can be obtained by calling the IBM
Hotline at 1-800-300-8751.
German safety information

Das Produkt ist nicht für den Einsatz an Bildschirmarbeitsplätzen im Sinne § 2 der
Bildschirmarbeitsverordnung geeignet.
Laser safety information

IBM servers can use I/O cards or features that are fiber-optic based and that utilize lasers or LEDs.
Laser compliance
IBM servers may be installed inside or outside of an IT equipment rack.
DANGER: When working on or around the system, observe the following precautions:
Electrical voltage and current from power, telephone, and communication cables are hazardous. To
avoid a shock hazard: If IBM supplied the power cord(s), connect power to this unit only with the
IBM provided power cord. Do not use the IBM provided power cord for any other product. Do not
open or service any power supply assembly. Do not connect or disconnect any cables or perform
installation, maintenance, or reconfiguration of this product during an electrical storm.
• The product might be equipped with multiple power cords. To remove all hazardous
voltages, disconnect all power cords. For AC power, disconnect all power cords from their AC power
source. For racks with a DC power distribution panel (PDP), disconnect the customer’s DC power source
to the PDP.
• When connecting power to the product ensure all power cables are properly connected. For racks with
AC power, connect all power cords to a properly wired and grounded electrical outlet. Ensure that the
outlet supplies proper voltage and phase rotation according to the system rating plate. For racks with a
DC power distribution panel (PDP), connect the customer’s DC power source to the PDP. Ensure that the
proper polarity is used when attaching the DC power and DC power return wiring.
• Connect any equipment that will be attached to this product to properly wired outlets.
© Copyright IBM Corp. 2018, 2021 v

• When possible, use one hand only to connect or disconnect signal cables.
• Never turn on any equipment when there is evidence of fire, water, or structural damage.
• Do not attempt to switch on power to the machine until all possible unsafe conditions are corrected.
• When performing a machine inspection: Assume that an electrical safety hazard is present. Perform
all continuity, grounding, and power checks specified during the subsystem installation procedures to
ensure that the machine meets safety requirements. Do not attempt to switch power to the machine
until all possible unsafe conditions are corrected. Before you open the device covers, unless instructed
otherwise in the installation and configuration procedures: Disconnect the attached AC power cords,
turn off the applicable circuit breakers located in the rack power distribution panel (PDP), and
disconnect any telecommunications systems, networks, and modems.
• Connect and disconnect cables as described in the following procedures when installing, moving, or
opening covers on this product or attached devices.
To Disconnect: 1) Turn off everything (unless instructed otherwise). 2) For AC power, remove the power
cords from the outlets. 3) For racks with a DC power distribution panel (PDP), turn off the circuit
breakers located in the PDP and remove the power from the Customer's DC power source. 4) Remove
the signal cables from the connectors. 5) Remove all cables from the devices.
To Connect: 1) Turn off everything (unless instructed otherwise). 2) Attach all cables to the devices. 3)
Attach the signal cables to the connectors. 4) For AC power, attach the power cords to the outlets. 5)
For racks with a DC power distribution panel (PDP), restore the power from the Customer's DC power
source and turn on the circuit breakers located in the PDP. 6) Turn on the devices.
• Sharp edges, corners and joints may be present in and around the system. Use
care when handling equipment to avoid cuts, scrapes and pinching. (D005)
(R001 part 1 of 2):
DANGER: Observe the following precautions when working on or around your IT rack system:
• Heavy equipment–personal injury or equipment damage might result if mishandled.
• Always lower the leveling pads on the rack cabinet.
• Always install stabilizer brackets on the rack cabinet if provided, unless the earthquake option is
to be installed.
• To avoid hazardous conditions due to uneven mechanical loading, always install the heaviest
devices in the bottom of the rack cabinet. Always install servers and optional devices starting
from the bottom of the rack cabinet.
• Rack-mounted devices are not to be used as shelves or work spaces. Do not place objects on top
of rack-mounted devices. In addition, do not lean on rack mounted devices and do not use them
to stabilize your body position (for example, when working from a ladder).
• Stability hazard:
– The rack may tip over causing serious personal injury.
– Before extending the rack to the installation position, read the installation instructions.
– Do not put any load on the slide-rail mounted equipment mounted in the installation position.
– Do not leave the slide-rail mounted equipment in the installation position.
• Each rack cabinet might have more than one power cord.
– For AC powered racks, be sure to disconnect all power cords in the rack cabinet when directed
to disconnect power during servicing.
vi Power Systems: Adapters for the 9040-MR9

– For racks with a DC power distribution panel (PDP), turn off the circuit breaker that controls
the power to the system unit(s), or disconnect the customer’s DC power source, when directed
to disconnect power during servicing.
• Connect all devices installed in a rack cabinet to power devices installed in the same rack
cabinet. Do not plug a power cord from a device installed in one rack cabinet into a power device
installed in a different rack cabinet.
• An electrical outlet that is not correctly wired could place hazardous voltage on the metal parts
of the system or the devices that attach to the system. It is the responsibility of the customer to
ensure that the outlet is correctly wired and grounded to prevent an electrical shock. (R001 part
1 of 2)
(R001 part 2 of 2):
CAUTION:
• Do not install a unit in a rack where the internal rack ambient temperatures will exceed the
manufacturer's recommended ambient temperature for all your rack-mounted devices.
• Do not install a unit in a rack where the air flow is compromised. Ensure that air flow is not
blocked or reduced on any side, front, or back of a unit used for air flow through the unit.
• Consideration should be given to the connection of the equipment to the supply circuit so that
overloading of the circuits does not compromise the supply wiring or overcurrent protection.
To provide the correct power connection to a rack, refer to the rating labels located on the
equipment in the rack to determine the total power requirement of the supply circuit.
• (For sliding drawers.) Do not pull out or install any drawer or feature if the rack stabilizer brackets
are not attached to the rack or if the rack is not bolted to the floor. Do not pull out more than one
drawer at a time. The rack might become unstable if you pull out more than one drawer at a time.
• (For fixed drawers.) This drawer is a fixed drawer and must not be moved for servicing unless
specified by the manufacturer. Attempting to move the drawer partially or completely out of the
rack might cause the rack to become unstable or cause the drawer to fall out of the rack. (R001
part 2 of 2)
CAUTION: Removing components from the upper positions in the rack cabinet improves rack
stability during relocation. Follow these general guidelines whenever you relocate a populated rack
cabinet within a room or building.
• Reduce the weight of the rack cabinet by removing equipment starting at the top of the rack
cabinet. When possible, restore the rack cabinet to the configuration of the rack cabinet as you
received it. If this configuration is not known, you must observe the following precautions:
– Remove all devices in the 32U position and above.
– Ensure that the heaviest devices are installed in the bottom of the rack cabinet.
Safety notices vii

– Ensure that there are little-to-no empty U-levels between devices installed in the rack cabinet
below the 32U level, unless the received configuration specifically allowed it.
• If the rack cabinet you are relocating is part of a suite of rack cabinets, detach the rack cabinet
from the suite.
• If the rack cabinet you are relocating was supplied with removable outriggers they must be
reinstalled before the cabinet is relocated.
• Inspect the route that you plan to take to eliminate potential hazards.
• Verify that the route that you choose can support the weight of the loaded rack cabinet. Refer to
the documentation that comes with your rack cabinet for the weight of a loaded rack cabinet.
• Verify that all door openings are at least 760 x 2083 mm (30 x 82 in.).
• Ensure that all devices, shelves, drawers, doors, and cables are secure.
• Ensure that the four leveling pads are raised to their highest position.
• Ensure that there is no stabilizer bracket installed on the rack cabinet during movement.
• Do not use a ramp inclined at more than 10 degrees.
• When the rack cabinet is in the new location, complete the following steps:
– Lower the four leveling pads.
– Install stabilizer brackets on the rack cabinet or in an earthquake environment bolt the rack to
the floor.
– If you removed any devices from the rack cabinet, repopulate the rack cabinet from the lowest
position to the highest position.
• If a long-distance relocation is required, restore the rack cabinet to the configuration of the rack
cabinet as you received it. Pack the rack cabinet in the original packaging material, or equivalent.
Also lower the leveling pads to raise the casters off of the pallet and bolt the rack cabinet to the
pallet.
(R002)
(L001)
DANGER: Hazardous voltage, current, or energy levels are present inside any component that has
this label attached. Do not open any cover or barrier that contains this label. (L001)
(L002)
DANGER: Rack-mounted devices are not to be used as shelves or work spaces. Do not place
objects on top of rack-mounted devices. In addition, do not lean on rack-mounted devices and do
not use them to stabilize your body position (for example, when working from a ladder). Stability
hazard:
• The rack may tip over causing serious personal injury.
• Before extending the rack to the installation position, read the installation instructions.
viii Power Systems: Adapters for the 9040-MR9

• Do not put any load on the slide-rail mounted equipment mounted in the installation position.
• Do not leave the slide-rail mounted equipment in the installation position.
(L002)
(L003)
or
or
or
or
Safety notices ix
DANGER: Multiple power cords. The product might be equipped with multiple AC power cords
or multiple DC power cables. To remove all hazardous voltages, disconnect all power cords and
power cables. (L003)
(L007)
CAUTION: A hot surface nearby. (L007)
(L008)
CAUTION: Hazardous moving parts nearby. (L008)
All lasers are certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for class
1 laser products. Outside the U.S., they are certified to be in compliance with IEC 60825 as a class 1 laser
product. Consult the label on each part for laser certification numbers and approval information.
CAUTION: This product might contain one or more of the following devices: CD-ROM drive, DVD-
ROM drive, DVD-RAM drive, or laser module, which are Class 1 laser products. Note the following
information:
• Do not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
• Use of the controls or adjustments or performance of procedures other than those specified
herein might result in hazardous radiation exposure.
(C026)
x Power Systems: Adapters for the 9040-MR9

CAUTION: Data processing environments can contain equipment transmitting on system links with
laser modules that operate at greater than Class 1 power levels. For this reason, never look into
the end of an optical fiber cable or open receptacle. Although shining light into one end and looking
into the other end of a disconnected optical fiber to verify the continuity of optic fibers may not
injure the eye, this procedure is potentially dangerous. Therefore, verifying the continuity of optical
fibers by shining light into one end and looking at the other end is not recommended. To verify
continuity of a fiber optic cable, use an optical light source and power meter. (C027)
CAUTION: This product contains a Class 1M laser. Do not view directly with optical instruments.
(C028)
CAUTION: Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the
following information:
• Laser radiation when open.
• Do not stare into the beam, do not view directly with optical instruments, and avoid direct
exposure to the beam. (C030)
(C030)
CAUTION: The battery contains lithium. To avoid possible explosion, do not burn or charge the
battery.
Do Not:
• Throw or immerse into water
• Heat to more than 100 degrees C (212 degrees F)
• Repair or disassemble
Exchange only with the IBM-approved part. Recycle or discard the battery as instructed by
local regulations. In the United States, IBM has a process for the collection of this battery. For
information, call 1-800-426-4333. Have the IBM part number for the battery unit available when
you call. (C003)
CAUTION: Regarding IBM provided VENDOR LIFT TOOL:
• Operation of LIFT TOOL by authorized personnel only.
• LIFT TOOL intended for use to assist, lift, install, remove units (load) up into rack elevations. It is
not to be used loaded transporting over major ramps nor as a replacement for such designated
tools like pallet jacks, walkies, fork trucks and such related relocation practices. When this is not
practicable, specially trained persons or services must be used (for instance, riggers or movers).
• Read and completely understand the contents of LIFT TOOL operator's manual before using.
Failure to read, understand, obey safety rules, and follow instructions may result in property
damage and/or personal injury. If there are questions, contact the vendor's service and support.
Local paper manual must remain with machine in provided storage sleeve area. Latest revision
manual available on vendor's web site.
• Test verify stabilizer brake function before each use. Do not over-force moving or rolling the LIFT
TOOL with stabilizer brake engaged.
• Do not raise, lower or slide platform load shelf unless stabilizer (brake pedal jack) is fully
engaged. Keep stabilizer brake engaged when not in use or motion.
• Do not move LIFT TOOL while platform is raised, except for minor positioning.
• Do not exceed rated load capacity. See LOAD CAPACITY CHART regarding maximum loads at
center versus edge of extended platform.
• Only raise load if properly centered on platform. Do not place more than 200 lb (91 kg) on edge
of sliding platform shelf also considering the load's center of mass/gravity (CoG).
• Do not corner load the platforms, tilt riser, angled unit install wedge or other such accessory
options. Secure such platforms -- riser tilt, wedge, etc options to main lift shelf or forks in all four
(4x or all other provisioned mounting) locations with provided hardware only, prior to use. Load
objects are designed to slide on/off smooth platforms without appreciable force, so take care not
Safety notices xi
to push or lean. Keep riser tilt [adjustable angling platform] option flat at all times except for final
minor angle adjustment when needed.
• Do not stand under overhanging load.
• Do not use on uneven surface, incline or decline (major ramps).
• Do not stack loads.
• Do not operate while under the influence of drugs or alcohol.
• Do not support ladder against LIFT TOOL (unless the specific allowance is provided for one
following qualified procedures for working at elevations with this TOOL).
• Tipping hazard. Do not push or lean against load with raised platform.
• Do not use as a personnel lifting platform or step. No riders.
• Do not stand on any part of lift. Not a step.
• Do not climb on mast.
• Do not operate a damaged or malfunctioning LIFT TOOL machine.
• Crush and pinch point hazard below platform. Only lower load in areas clear of personnel and
obstructions. Keep hands and feet clear during operation.
• No Forks. Never lift or move bare LIFT TOOL MACHINE with pallet truck, jack or fork lift.
• Mast extends higher than platform. Be aware of ceiling height, cable trays, sprinklers, lights, and
other overhead objects.
• Do not leave LIFT TOOL machine unattended with an elevated load.
• Watch and keep hands, fingers, and clothing clear when equipment is in motion.
• Turn Winch with hand power only. If winch handle cannot be cranked easily with one hand, it
is probably over-loaded. Do not continue to turn winch past top or bottom of platform travel.
Excessive unwinding will detach handle and damage cable. Always hold handle when lowering,
unwinding. Always assure self that winch is holding load before releasing winch handle.
• A winch accident could cause serious injury. Not for moving humans. Make certain clicking sound
is heard as the equipment is being raised. Be sure winch is locked in position before releasing
handle. Read instruction page before operating this winch. Never allow winch to unwind freely.
Freewheeling will cause uneven cable wrapping around winch drum, damage cable, and may
cause serious injury.
• This TOOL must be maintained correctly for IBM Service personnel to use it. IBM shall inspect
condition and verify maintenance history before operation. Personnel reserve the right not to use
TOOL if inadequate. (C048)
Power and cabling information for NEBS (Network Equipment-Building System)

GR-1089-CORE
The following comments apply to the IBM servers that have been designated as conforming to NEBS
(Network Equipment-Building System) GR-1089-CORE:
The equipment is suitable for installation in the following:
• Network telecommunications facilities
• Locations where the NEC (National Electrical Code) applies
The intrabuilding ports of this equipment are suitable for connection to intrabuilding or unexposed wiring
or cabling only. The intrabuilding ports of this equipment must not be metallically connected to the
interfaces that connect to the OSP (outside plant) or its wiring. These interfaces are designed for use as
intrabuilding interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation
from the exposed OSP cabling. The addition of primary protectors is not sufficient protection to connect
these interfaces metallically to OSP wiring.
Note: All Ethernet cables must be shielded and grounded at both ends.
The ac-powered system does not require the use of an external surge protection device (SPD).
xii Power Systems: Adapters for the 9040-MR9

The dc-powered system employs an isolated DC return (DC-I) design. The DC battery return terminal shall
not be connected to the chassis or frame ground.
The dc-powered system is intended to be installed in a common bonding network (CBN) as described in
GR-1089-CORE.
Safety notices xiii

xiv Power Systems: Adapters for the 9040-MR9
Installing, removing, and replacing adapters in the
9040-MR9 system
Find information about installing, removing, and replacing adapters in the IBM Power® System E950
(9040-MR9) server.
Installing adapters in the 9040-MR9 system

Find information about installing adapters in the IBM Power System E950 (9040-MR9) server.
About this task

Note: Installing this feature is a customer task. You can complete this task yourself, or contact a service
provider to complete the task for you. You might be charged a fee by the service provider for this service.
If your system is managed by the Hardware Management Console (HMC), use the HMC to complete
the steps for installing an adapter in the system. For instructions, see Installing a part by using the
HMC (www.ibm.com/support/knowledgecenter/POWER9/p9haj/hmcinstall.htm).
If your system is not managed by an HMC, complete the steps in the following procedures to install an
adapter in the system.
Preparing the 9040-MR9 system to install an adapter

To prepare the system to install an adapter, complete the steps in this procedure.
Before you begin

Note: If you are installing a PCIe3 cable adapter to attach your server to an EMX0 PCIe3 expansion
drawer, you must ensure that you have the correct PCIe3 cable adapter and expansion drawer cable that
works with the PCIe3 6-slot fanout module that you have in your EMX0 PCIe3 expansion drawer.
• If you have a CCIN 50CB PCIe3 6-slot fanout module:
– You must use one of the following PCIe3 cable adapters:
- FC EJ08 (CCIN 2CE2)
- FC EJ07 (CCIN 6B52)
- FC EJ05 (CCIN 2B1C)
– You must use one of the following expansion drawer cables: FC ECC6, FC ECC7, FC ECC8, FC ECC9,
FC ECCR, FC ECCS, FC ECCX, FC ECCY, or FC ECCZ.
• If you have a CCIN 50CD PCIe3 6-slot fanout module:
– You must install one of the following PCIe3 cable adapters:
- FC EJ1R (CCIN 58FF)
- FC EJ20 (CCIN 2CF5)
– You must use one of the following expansion drawer cables: FC ECCR, FC ECCS, FC ECCX, FC ECCY, or
FC ECCZ.
Important: You need to work with the system administrator to prepare the adapter slot to receive the
adapter. If this process exceeds the 10-minute service limitation with the system access cover removed,
place the service access cover back on the system before working with the system administrator to
maintain proper system cooling.
© Copyright IBM Corp. 2018, 2021 1

Procedure
1. If you are installing a PCIe3 cable adapter with the system power turned on, you must install the
PCIe3 cable adapter by using the HMC. Otherwise, you must install the PCIe3 cable adapter with the
system power turned off.
2. Ensure that the required software is installed to support the new feature. See the Power Systems
Prerequisites website.
Important: If you are installing a PCIe3 cable adapter and want to connect an EMX0 PCIe3
expansion drawer via the HMC, you must have the HMC driver 9.1.921.0 or later installed.
3. Take appropriate precautions for avoiding electric shock and for handling static-sensitive devices. For
more information, see “Avoiding electric shock” on page 49 and “Handling static-sensitive devices”
on page 50.
4. If you are installing a PCIe3 cable adapter, ensure that the target slot is Unassigned in the I/O
properties field for the managed server you are working on.
5. If applicable, open the rack door at the rear of the system.
6. Review the adapter slot locations.
The adapter slots are at the rear of a system.
The number of the adapter slots that are available in the system depends on the number of system
processors in the system. For the adapter placement information for the available slots in this
system, see Adapter placement rules and slot priorities for the 9040-MR9.
The adapter has two LEDs that indicate the following status:
• A power/activity LED (green)
• An error and identify function LED (amber)
The status of the LEDs are as follows:
• (B) Indicates that the adapter is operating correctly. The green power LED (top LED) is lit solid and
the amber fault LED (bottom LED) is off.
• (C) Indicates that the adapter is not operating correctly. The green power LED (top LED) is lit solid
and the amber fault LED (bottom LED) is lit solid.
• (D) Indicates the faulty or failed adapter was selected by using the identify function. The green
power LED (top LED) might or might not be lit and the amber fault LED (bottom LED) is flashing.
2 Power Systems: Adapters for the 9040-MR9

Figure 1. Adapter slot and LED locations in a 9040-MR9 system
7. Choose from the following options:
• If you want to install an adapter when the system power is turned off, continue with step “8” on
page 3.
• If the system power is turned on and if the AIX® operating system controls the slot, continue with
step “10” on page 6.
• If the system power is turned on and if the Linux® operating system controls the slot, continue with
8. To prepare the system to install an adapter when the system is powered off, complete the following
steps:
a) Activate the identify function. For instructions, see Identifying a part (www.ibm.com/support/
knowledgecenter/POWER9/p9haj/sal.htm).
b) Physically verify that the slot you identified is where you want to install the adapter.
• Use the blue identify LED on the enclosure to locate the system. Ensure that the serial number
of the system matches the serial number to be serviced.
• Look for a flashing amber LED, which identifies the unoccupied slot that was selected by using
the identify function.
c) Stop the system. For instructions, see Stopping a system (www.ibm.com/support/
knowledgecenter/POWER9/p9haj/crustopsys.htm).
Installing, removing, and replacing adapters in the 9040-MR9 system 3

9. If you powered the system off, complete the following steps:
a) If applicable, open the rack door at the rear of the system.
b) Label and disconnect the power cords from the system unit as shown in the following figure.
Notes:
• This system might be equipped with two or more power supplies. If the removing and replacing
procedures require the system power to be turned off, ensure that all power sources to the
system are disconnected.
• The power cord (B) is fastened to the system with a hook-and-loop fastener (A). If you are
placing the system in a service position after you disconnect the power cords, ensure that you
unstrap the fastener.
Figure 2. Removing the power cords
(L003)
or

or
or
or

DANGER: Multiple power cords. The product might be equipped with multiple AC power
cords or multiple DC power cables. To remove all hazardous voltages, disconnect all power
cords and power cables. (L003)
c) Continue with step “12” on page 7.
10. To prepare the system to install an adapter by using the AIX operating system, complete the following
steps:
a) Log in to the console as root user to access the Hot Plug Manager.
b) At the command line, type smitty.
c) Select Devices > PCI Hot Plug Manager and press Enter.
The PCI Hot-Plug Manager menu displays.
For more information about the menu options in the PCI Hot-Plug Manager
screen, see Hot-plug manager menu (www.ibm.com/support/knowledgecenter/POWER9/p9hak/
p9hak_hotplug_menu.htm).
d) From the PCI Hot-Plug Manager menu, select Add a PCI Hot-Plug Adapter, and then press Enter.
e) Select the appropriate slot from the list that is displayed on the screen, and then press Enter.
f) Physically verify that the slot you identified is where you want to install the adapter.
g) Continue with step “12” on page 7.
11. To prepare the system to install an adapter by using the Linux operating system, complete the
following steps:
a) Log in to the system console as the root user.
b) Run the following command to list the available slots:
lsslot -c pci -a
The following screen is an example of the information that is displayed by this command:
# Slot Description Device(s)

U7879.001.DQD014E-P1-C1 PCI-X capable, 64 bit, 133MHz slot Empty
c) Record the empty adapter slot where you want to install the adapter.
d) Complete the following steps to prepare the slot to accept an adapter:
i) Type the following command:
drmgr -c pci -a -s locationcode

Where locationcode is the location of the adapter slot. For example, the location might be
U7879.001.DQD014E-P1-C3.
ii) Press Enter. A fast-flashing amber LED at the rear of the system near the adapter indicates that
the slot is identified.
iii) Physically verify that the slot you identified is where you want to install the adapter.
Notes:
• Use the blue identify LED on the enclosure to locate the system. Ensure that the serial
number of the system matches the serial number to be serviced.
• Look for the flashing amber LED, which identifies the slot that was selected by using the
identify function.
e) Physically verify that the slot you identified is where you want to install the adapter.
12. At the rear of the system, put the cable management bracket in the service position. See the
following figure.
a) Pull out the quarter-turn fasteners (B) and turn them to disengage them while you lift the cable
management bracket (A) to its raised position.
b) Turn the quarter-turn fasteners (B) to engage and lock the bracket into position.

Figure 3. Placing the cable management bracket in the raised service position
13. Attach the electrostatic discharge (ESD) wrist strap.
The ESD wrist strap must be connected to an unpainted metal surface until the service procedure is
completed, and if applicable, until the service access cover is replaced.
Attention:
• Attach an electrostatic discharge (ESD) wrist strap to the front ESD jack, to the rear ESD jack,
or to an unpainted metal surface of your hardware to prevent the electrostatic discharge
from damaging your hardware.
• When you use an ESD wrist strap, follow all electrical safety procedures. An ESD wrist strap
is used for static control. It does not increase or decrease your risk of receiving electric
shock when using or working on electrical equipment.
• If you do not have an ESD wrist strap, just prior to removing the product from ESD packaging
and installing or replacing hardware, touch an unpainted metal surface of the system for
a minimum of 5 seconds. If at any point in this service process you move away from the
system, it is important to again discharge yourself by touching an unpainted metal surface
for at least 5 seconds before you continue with the service process.

Installing an adapter in the 9040-MR9 system
To install an adapter in the system, complete the steps in this procedure.
Procedure
1. Ensure that you have the electrostatic discharge (ESD) wrist strap on and that the ESD clip is plugged
into a ground jack or connected to an unpainted metal surface. If not, do so now.
2. If necessary, remove the adapter from the antistatic package.
Attention: Avoid touching the components and gold connectors on the adapter.
3. Place the adapter, component-side up, on a flat, antistatic surface.
Attention: A pin on the tailstock of the adapter resembles a removable screw. Do not remove
this pin. It is required for correct alignment and seating.
4. Remove the cassette from the slot:
a) Squeeze the latch lever (A) and press down on the latch (B) in the direction shown.
This action pivots the cassette forward and releases the cassette from the slot.
b) Pull out the cassette from its slot.
Figure 4. Removing an adapter cassette from the 9040-MR9 system

5. Remove the tailstock filler from the cassette.
a) Open the tailstock clamp (A) by rotating the clamp in the direction that is shown.
b) Press and slide the release bar (B) in the direction that is shown to open the cassette.
c) Grasp the tailstock filler and pull the filler away from the cassette in the direction that is shown.

Figure 5. Removing a tailstock filler from the cassette for the 9040-MR9 system
Note: Your cassette might not have the two adapter retainers (C) and strips.
d) Save the tailstock filler for a future use.
You must have a tailstock filler in an empty cassette in a system to ensure proper airflow.
• To install an adapter into a cassette that has adapter retainers and strips, continue with step “7” on
page 10.
• To install an adapter into a cassette that doesn't have adapter retainers and strips, continue with
step 8.
7. If your cassette has two adapter retainers with strips, complete the following steps to install or replace
an adapter into the cassette:
a) If the adapter retainers (A) haven't already been removed, remove the adapter retainers (A) by
putting them in the open position and moving them all the way off the strips.
b) Press and slide the release bar (B) to open the cassette.
c) Place an ESD safety sheet (C) over the strips.
Note: You can use the ESD package that the new adapter was in. If necessary, cut it to size.

Figure 6. Placing an ESD safety sheet over the strips on the 9040-MR9 cassette
d) Insert the adapter into the cassette.
e) Press and slide the release bar (A) to close the cassette.
f) Close the tailstock clamp (B) by rotating the clamp in the direction that is shown.
g) Pull the ESD safety film (C) out.

Figure 7. Installing an adapter in the cassette for the 9040-MR9 system
h) With the adapter retainers (D) in the open position, slide the retainers onto the strips.
i) Position the adapter retainers (D) so that they support the adapter and put them in the locked
position by rotating them in the direction that is shown.
Note: Ensure that the adapter is secured in the adapter retainer channel.

Figure 8. Securing an adapter with the adapter retainers for the 9040-MR9 system
8. If your cassette does not have the two adapter retainers and strips, complete the following steps to
install or replace an adapter into the cassette:
a) Press and slide the release bar (A) to open the cassette.
b) Insert the adapter into the cassette.
c) Press and slide the release bar (A) to close the cassette.
d) Close the tailstock clamp (B) by rotating the clamp in the direction that is shown.

9. Slide the cassette into the slot by completing the following steps:
Attention:
Ensure proper alignment when you insert an adapter cassette into the system.
a) Align the cassette on the cassette rail in the cassette slot.
b) Slide the cassette forward until the cassette is fully seated.
c) To lock the cassette in its slot, squeeze the latch lever (A) toward the latch (B) and rotate the latch
(B) in the direction that is shown.

Figure 10. Installing a cassette in the 9040-MR9 system
Preparing the 9040-MR9 system for operation after installing an adapter

To prepare the system for operation after installing an adapter, complete the steps in this procedure.
Procedure
2. If you installed a PCIe3 cable adapter, and want to connect an EMX0 PCIe3 expansion drawer to your
system, continue with Connecting an EMX0 PCIe Gen3 I/O expansion drawer to your system (http://
www.ibm.com/support/knowledgecenter/POWER9/p9egp/p9egp_connect_kickoff.htm).
If you have an HMC-managed 9040-MR9 or 9080-M9S system, you can connect and activate the
expansion drawer cable when the system power is turned on. Otherwise, you must connect the cable
with the system power turned off. The cable is activated when you start the system.
3. If removed, connect the cables or transceivers to the adapter.
4. Route the cables through the cable management bracket.
5. If not already connected, reconnect the power cords (A) to the system unit. Fasten the power cords to
the system using the hook-and-loop fasteners (B) as shown in the following figure.

Figure 11. Connecting the power cords
6. Put the cable management bracket in the operating position. See the following figure.
a) Pull out the quarter-turn fasteners (B) and turn them to disengage them while moving the cable
management bracket (A) to its lower position.

Figure 12. Placing the cable management bracket in the lowered operating position
7. Close the rack door at the rear of the system.
• If the system power is turned off, continue with step “9” on page 17.
• If you are using the AIX operating system, continue with step “10” on page 17.
• If you are using the Linux operating system, continue with step “11” on page 17.
9. If the system power is turned off, complete the following steps:
a) Start the system. For instructions, see Starting a system (www.ibm.com/support/
knowledgecenter/POWER9/p9haj/crustartsys.htm).
b) Continue with step “12” on page 18.
10. If you are using the AIX operating system, you must configure the adapter by completing the
following steps:
a) Install the AIX device drivers for the installed adapter.
For instructions, see Installing the AIX device driver software.
b) On the console, enter cfgmgr to configure the adapter.
11. If you are using the Linux operating system, complete the following steps:

a) In the Linux session on the console, press Enter after you install or replace the adapter to put the
slot into the action state.
b) Enter the slot information with the lsslot command, as shown in the following example.
For example, if the slot in which you installed the adapter was U7879.001.DQD014E-P1-C3.
Enter lsslot -c pci -s U7879.001.DQD014E-P1-C3

U7879.001.DQD014E-P1-C3 PCI-X capable, 64 bit, 133MHz slot 0001:40:01.0
12. Verify the installed part.

• If you replaced the part because of a service action, verify the installed part. For
instructions, see Verifying a repair (www.ibm.com/support/knowledgecenter/POWER9/p9ect/
pxect_verifyrepair.htm).
• If you installed the part for any other reason, verify the installed part. For instructions, see Verifying
the installed part (www.ibm.com/support/knowledgecenter/POWER9/p9haj/pxhaj_hsmverify.htm).
13. Turn off the identify LED. For instructions, see Deactivating an identify LED (www.ibm.com/support/
knowledgecenter/POWER9/p9haj/p9haj_turn_off_identify_led.htm).
Removing and replacing an adapter in the 9040-MR9 system

Find information about removing and replacing an adapter in the IBM Power System E950 (9040-MR9)
server.
About this task

Note: Removing or replacing this feature is a customer task. You can complete this task yourself, or
contact a service provider to complete the task for you. You might be charged a fee by the service provider
for this service.
If your system is managed by the Hardware Management Console (HMC), use the HMC to repair a
part in the system. For instructions, see Repairing a part by using the HMC (www.ibm.com/support/
knowledgecenter/POWER9/p9haj/p9haj_hmc_repair.htm).
If your system is not managed by an HMC, complete the steps in the following procedures to remove and
replace an adapter in the system.
Preparing the 9040-MR9 system to remove and replace an adapter

To prepare the system to remove and replace an adapter in the system, complete the steps in this
procedure.
Before you begin

Note: If you are replacing a PCIe3 cable adapter that you use to attach your server to an EMX0 PCIe3
expansion drawer, you must ensure that you have the correct PCIe3 cable adapter and expansion drawer
cable to work with the PCIe3 6-slot fanout module that you have in your EMX0 PCIe3 expansion drawer.
• If you have a CCIN 50CB PCIe3 6-slot fanout module:
– You must use one of the following PCIe3 cable adapters:
- FC EJ08 (CCIN 2CE2)
- FC EJ05 (CCIN 2B1C)

– You must use one of the following expansion drawer cables: FC ECC6, FC ECC7, FC ECC8, FC ECC9,
FC ECCR, FC ECCS, FC ECCX, FC ECCY, or FC ECCZ.
• If you have a CCIN 50CD PCIe3 6-slot fanout module:
– You must install one of the following PCIe3 cable adapters:
- FC EJ1R (CCIN 58FF)
- FC EJ20 (CCIN 2CF5)
– You must use one of the following expansion drawer cables: FC ECCR, FC ECCS, FC ECCX, FC ECCY, or
FC ECCZ.
About this task
Procedure
on page 50.
3. Review the locations of the adapter slots and the service indicators for the adapter that you want
to service. The adapters are installed in the rear of the system. Figure 13 on page 20 shows the
locations of the adapters in a 9040-MR9 system and the locations of the light-emitting diodes (LEDs)
for the adapter.
The number of adapter slots that are available in the system depends on the number of system
The adapter has two LEDs that indicate the status:
power LED (top LED) is lit and the amber fault LED (bottom LED) is flashing.
Attention: If the adapter is operating correctly, then the Activity LED is ON (green) and the
Error amber LED is OFF, as shown in (B). Do not attempt to remove a working adapter.

• If you want to remove an adapter when the system power is turned off, continue with step “5” on
page 20.
• If the system power is turned on and if the AIX operating system controls the slot, continue with
• If the system power is turned on and if the Linux operating system controls the slot, continue with
5. To prepare the system to remove an adapter when the system is powered off, complete the following
steps:
a) Turn on the identify LED for the failing adapter.
For instructions, see Identifying a part (www.ibm.com/support/knowledgecenter/POWER9/p9haj/
sal.htm).
Use the blue identify LED on the enclosure to locate the system. Ensure that the serial number of
the system matches the serial number to be serviced.
b) Physically verify that the slot you identified is where you want to install the adapter.

c) If you have not yet recorded the adapter slot details, record the slot number and location of each
adapter that is being removed.
Note: Adapter slots are numbered on the rear of the system.
d) Stop the system. For instructions, see Stopping a system (www.ibm.com/support/
knowledgecenter/POWER9/p9haj/crustopsys.htm).
6. If you powered the system off, complete the following steps:
a) If applicable, open the rack door at the rear of the system.
b) Label and disconnect the power cords from the system unit as shown in the following figure.
Notes:
procedures require the system power to be turned off, ensure that all power sources to the
system are disconnected.
• The power cord (B) is fastened to the system with a hook-and-loop fastener (A). If you are
placing the system in a service position after you disconnect the power cords, ensure that you
unstrap the fastener.

(L003)
or
or
or
or

DANGER: Multiple power cords. The product might be equipped with multiple AC power
cords or multiple DC power cables. To remove all hazardous voltages, disconnect all power
cords and power cables. (L003)
7. To prepare to remove an adapter by using the AIX operating system, complete the following steps:
a) You must take the adapter offline before you remove and replace an adapter when the system
power is turned on (hot-plugging). Before you take an adapter offline, the devices that are
attached to the adapter must be taken offline as well. This action must be done by a system
administrator. Taking the adapter offline prevents a service representative or user from causing an
unexpected outage for other users of the system.
b) Before hot-plugging adapters or storage devices, ensure that the file systems on those devices are
unmounted.
c) Ensure that any processes or applications that might use the adapter are stopped.
d) To identify the failed adapter, complete the steps in this procedure on the console:
i) Log in as root user.
ii) At the command line, type diag and then press Enter.
iii) From the Function Selection menu, select Task Selection > Hot Plug Task > PCI Hot Plug
Manager > Unconfigure a Device.
iv) Press F4 (or Esc +4) to display the Device Names menu.
v) Select the adapter that you are removing in the Device Names menu.
vi) Use the Tab key to answer No to Keep Definition. Use the Tab key again to answer Yes to
Unconfigure Child Devices, and then press Enter. Press Enter to confirm the operation. The
OK message next to the Command field confirms a successful unconfiguration.
vii) Press F3 (or Esc +3) twice to return to the Hot Plug Manager menu.
viii) Select replace/remove PCI Hot Plug adapter and then select the slot that contains the
adapter to be removed from the system.
ix) Select remove. The amber LED for the adapter flashes for the slot that is identified.
x) Physically verify that the slot you identified is where you want to remove the adapter.
Notes:

identify function.
xi) Press Enter. The adapter is placed in the action state and is ready to be removed from the
system.
e) If necessary to view the identify LEDs or to manage cables at the rear of a rack-mounted system,
open the cable management arm by completing the following steps:
i) Release the mounting bracket from the cable management arm assembly by pressing the
indentation (A) on the inner cable management arm tab. The cable management arm releases
from the outer mounting bracket in the direction shown.
Figure 15. Releasing the mounting bracket

ii) Swing the cable management arm away from the system.
In the image, the inner cable management arm tab is shown on the left side as you are facing
the system from the rear. However, the cable management arm can also be installed so that the
inner cable management arm tab is on the right side of the system.
CAUTION: To avoid causing damage to the arm, open the cable management arm just
long enough to complete these repairs.
f) Physically verify that the slot you identified is where you want to remove the adapter.

• Look for a flashing amber LED, which identifies the slot that was selected by using the identify
function.
8. To prepare to remove an adapter by using the Linux operating system, complete the following steps:
a) Before you hot-plug an adapter, ensure that the server or partition is at the correct level of the
Linux operating system.
b) Verify that the Linux, hot-plug adapter tools are installed.
For instructions, see Verifying that the hot-plug adapter tools are installed for
Linux (www.ibm.com/support/knowledgecenter/POWER9/p9hak/pxhak_linuxhotplugverify.htm).
c) Ensure that you have the POWER® Linux Service Aids installed on your system. These service aids
enable system serviceability, as well to improve system management. If you are using a Linux on
POWER distribution with Linux kernel version 2.6 or later, you can install the Service Aids that
gives you access to more capabilities, which can help you diagnose problems on your system.
This software is available at the Service and productivity tools for Linux on POWER website (http://
www14.software.ibm.com/webapp/set2/sas/f/lopdiags/home.html).
d) You must take the adapter offline before you remove and replace an adapter when the system
power is turned on (hot-plugging). Before you take an adapter offline, the devices that are
attached to the adapter must be taken offline as well. This action must be done by a system
administrator. Taking the adapter offline prevents a service representative or user from causing an
unexpected outage for other users of the system.
e) Before hot-plugging adapters or storage devices, ensure that the file systems on those devices are
unmounted.
f) Ensure that any processes or applications that might use the adapter are stopped.
g) Use the service indicator light-emitting diodes (LEDs) to help identify the part. For instructions,
see Identifying a part (www.ibm.com/support/knowledgecenter/POWER9/p9haj/sal.htm).
h) Physically verify that the slot you identified is where you want to install the adapter.
i) Use the Linux operating system drmgr command to prepare the adapter to be removed when the
system power is turned on.
i) Type the following command:
drmgr -c pci -r -s locationcode
Where locationcode is replaced with the location you identified earlier. For example,
U7879.001.DQD014E-P1-C3.
The following screen is displayed.
The visual indicator for the specified PCI slot has been set to the
identify state. Press Enter to continue or enter x to exit.
ii) Physically verify that the slot you identified is where you want to remove the adapter.
Notes:
identify function.

iii) Press Enter. The slot is ready to have an adapter removed. Continue to follow these instructions
until you are told to remove the adapter.
following figure.
11. Label and disconnect all of the cables or transceivers that are attached to the adapter you plan to
remove.
Use a hook-and-loop fastener to hold the cables in place.
Important: If you are disconnecting the SAS AZ cable which controls the internal disk bays, use extra
care when removing cables from the adapter connectors. Gently pull the blue tab straight back from
the system to release the latches that secure the SAS cable to the adapter. To prevent possible tab
breakage, do not pull the blue tab to the side; instead, pull the blue tab straight back. While gently
pulling the blue tab, unplug and remove the SAS cable from the adapter by pulling on the black SAS
cable itself. Do not apply extra pulling force on the blue tab to remove cable.

Attention:
Removing an adapter from the 9040-MR9 system

To remove an adapter from the system, complete the steps in this procedure.
Procedure

• To remove an adapter from a cassette that has adapter retainers and strips, continue with step “4”
on page 28.
• To remove an adapter from a cassette that doesn't have adapter retainers and strips, continue with
4. If your cassette has two adapter retainers and strips, complete the following steps to remove an
adapter from a cassette.
b) Remove the adapter retainers (B) by rotating them in the direction that is shown and moving them
all the way off the strips.
c) Open the cassette by pressing and sliding the release bar (C) in the direction that is shown.
d) Remove the adapter.

Figure 18. Removing an adapter from a cassette for the 9040-MR9 system
5. If your cassette doesn't have two adapter retainers and strips, complete the following steps to remove
the adapter from the cassette.
b) Open the cassette by pressing and sliding the release bar (B) in the direction that is shown.
c) Remove the adapter.

6. Place the removed adapter on an approved ESD surface.
Replacing an adapter in the 9040-MR9 system

To replace an adapter in the system, complete the steps in this procedure.
Procedure
2. Ensure that the target slot is empty.
• To replace an adapter into a cassette that has adapter retainers and strips, continue with step “6”
on page 30.
• To replace an adapter into a cassette that does not have adapter retainers and strips, continue
with step “8” on page 33.
6. If your cassette has two adapter retainers with strips, complete the following steps to install or
replace an adapter into the cassette:

a) If the adapter retainers (A) haven't already been removed, remove the adapter retainers (A) by
putting them in the open position and moving them all the way off the strips.
b) Press and slide the release bar (B) to open the cassette.
c) Place an ESD safety sheet (C) over the strips.
Note: You can use the ESD package that the new adapter was in. If necessary, cut it to size.
Figure 20. Placing an ESD safety sheet over the strips on the 9040-MR9 cassette
d) Insert the adapter into the cassette.
e) Press and slide the release bar (A) to close the cassette.
f) Close the tailstock clamp (B) by rotating the clamp in the direction that is shown.
g) Pull the ESD safety film (C) out.

h) With the adapter retainers (D) in the open position, slide the retainers onto the strips.
i) Position the adapter retainers (D) so that they support the adapter and put them in the locked
position by rotating them in the direction that is shown.
Note: Ensure that the adapter is secured in the adapter retainer channel.

Figure 22. Securing an adapter with the adapter retainers for the 9040-MR9 system
7. Continue with step “9” on page 34.
8. If your cassette does not have the two adapter retainers and strips, complete the following steps to
install or replace an adapter into the cassette:
a) Press and slide the release bar (A) to open the cassette.
b) Insert the adapter into the cassette.
c) Press and slide the release bar (A) to close the cassette.
d) Close the tailstock clamp (B) by rotating the clamp in the direction that is shown.

9. Place the cassette with the adapter in it on an antistatic surface.
10. Choose from the followings options:
a) If the system power is turned off, continue with step “14” on page 34.
b) If the system power is turned on and you are using the AIX operating system, continue with step
“11” on page 34.
c) If the system power is turned on and you are using the Linux operating system, continue with step
“13” on page 34.
11. If you are using the AIX operating system, use the diag command on the console to prepare the slot
to accept an adapter.
a) Select Add a PCI Hot Plug adapter from the Hot Plug Manager menu.
b) Select the slot from where you removed the adapter.
c) Press Enter again to put the slot into the action state.
A fast-flashing amber LED at the rear of the system near the adapter indicates that the slot is
identified and is ready to receive the adapter.
12. Continue with step “14” on page 34.
13. If you are using the Linux operating system, use the drmgr command on the console to prepare the
slot to accept an adapter.
For example, to install the adapter in slot U7879.001.DQD014E-P1-C3, type:
drmgr -c pci -a -s locationcode
In this example, you would replace locationcode with U7879.001.DQD014E-P1-C3.

Follow the instructions on the display to complete the task.

Attention:
Preparing the 9040-MR9 system for operation after removing and replacing
an adapter
To prepare the system for operation after removing and replacing an adapter, complete the steps in this
procedure.
Procedure
2. Connect any cables or transceivers to the adapter.
3. Route the cables through the cable management bracket.
4. If you removed the power cords, connect all power cords to the system that you are servicing.

• If you completed this procedure with the system power turned off, continue with step “8” on page
36.
• If you completed the procedure with the system power turned on and used the AIX operating
system, continue with step “9” on page 36.
• If you completed the procedure with the system power turned on and used the Linux operating
system, continue with step “11” on page 37.
8. To prepare the system for operation when the system is powered off, complete the following steps:
a) Start the system. For instructions, see Starting a system (www.ibm.com/support/
knowledgecenter/POWER9/p9haj/crustartsys.htm).
b) Continue with step “12” on page 37.
9. If you are using the AIX operating system, complete the following steps to configure the adapter:
a) Press the F3 key to return to the Task Selection list.
b) Select Log Repair Action.
c) Select the resource that was replaced and select Commit.
d) Press the F3 key to return to Task Selection List.

e) Select Hot Plug Task > PCI Hot Plug Manager > Configure a defined device.
f) Select the device that you replaced from the list, and then press Enter. The device is now
configured.
g) Press the F10 key to exit the diagnostic program.
10. If you are using the AIX operating system, complete the following steps to verify the adapter
replacement:
a) If the diagnostic menu is not displayed, type the diag command.
b) Select Advance Diagnostic Routines > Problem Determination.
c) Select the name of the resource that was replaced from the menu. If the resource replaced is not
shown, choose the resource that is associated with it.
d) Press Enter, and then press Commit (F7 or Esc+7).
e) Did the Problem Determination identify any problems?
• No: Continue to the next step.
• Yes: A problem is identified.
– If you are a customer, record the error information, and then contact your service provider.
– If you are an authorized service provider, return to map 210-5.
f) Press the F10 key to exit the diagnostic program.
11. If you are using the Linux operating system, complete the following steps:
a) In the Linux session on the console, press Enter after you install or replace the adapter to put the
slot into the action state.
b) Enter the slot information with the lsslot command, as shown in the following example.
For example, if the slot in which you installed the adapter was U7879.001.DQD014E-P1-C3.
Enter lsslot -c pci -s U7879.001.DQD014E-P1-C3

U7879.001.DQD014E-P1-C3 PCI-X capable, 64 bit, 133MHz slot 0001:40:01.0
12. Verify the installed part.

• If you replaced the part because of a service action, verify the installed part. For
instructions, see Verifying a repair (www.ibm.com/support/knowledgecenter/POWER9/p9ect/
pxect_verifyrepair.htm).
• If you installed the part for any other reason, verify the installed part. For instructions, see Verifying
the installed part (www.ibm.com/support/knowledgecenter/POWER9/p9haj/pxhaj_hsmverify.htm).
13. Turn off the identify LED. For instructions, see Deactivating an identify LED (www.ibm.com/support/
knowledgecenter/POWER9/p9haj/p9haj_turn_off_identify_led.htm).
14. If you replaced a Fibre Channel adapter, the customer might need to update the Fibre Channel SAS
path to the external storage subsystems with the new WWPN number or numbers.

Permanently removing an adapter from the 9040-MR9 system
Find information about permanently removing an adapter from the IBM Power System E950 (9040-MR9)
server.
About this task

Note: Removing or replacing this feature is a customer task. You can complete this task yourself, or
contact a service provider to complete the task for you. You might be charged a fee by the service provider
for this service.
If your system is managed by the Hardware Management Console (HMC), use the HMC to repair a
part in the system. For instructions, see Repairing a part by using the HMC (www.ibm.com/support/
knowledgecenter/POWER9/p9haj/p9haj_hmc_repair.htm).
If your system is not managed by an HMC, complete the steps in the following procedures to permanently
remove an adapter from the system.
Preparing the 9040-MR9 system to permanently remove an adapter

To prepare the system to permanently remove an adapter from the system, complete the steps in this
procedure.
Before you begin
Procedure
on page 50.
2. Review the locations of the adapter slots and the service indicators for the adapter that you want
to service. The adapters are installed in the rear of the system. Figure 26 on page 39 shows the
locations of the adapters in a 9040-MR9 system and the locations of the light-emitting diodes (LEDs)
for the adapter.
The number of adapter slots that are available in the system depends on the number of system
The adapter has two LEDs that indicate the status:
power LED (top LED) is lit and the amber fault LED (bottom LED) is flashing.
Attention: If the adapter is operating correctly, then the Activity LED is ON (green) and the
Error amber LED is OFF, as shown in (B). Do not attempt to remove a working adapter.

3. Use the service indicator light-emitting diodes (LEDs) to help identify the part. For instructions, see
Identifying a part (www.ibm.com/support/knowledgecenter/POWER9/p9haj/sal.htm).
5. Physically verify that the slot you identified is where you want to remove the adapter.
• Use the blue identify LED on the enclosure to locate the system. Ensure that the serial number of
the system matches the serial number to be serviced.
• Look for a flashing amber LED, which identifies the slot that was selected by using the identify
function.
6. If you have not yet recorded the adapter slot details, record the slot number and location of each
adapter that is being removed.
Note: Adapter slots are numbered on the rear of the system.
7. Stop the system. For instructions, see Stopping a system (www.ibm.com/support/knowledgecenter/
POWER9/p9haj/crustopsys.htm).
8. Label and disconnect the power cords from the system unit as shown in the following figure.
Notes:
procedures require the system power to be turned off, ensure that all power sources to the system
are disconnected.

• The power cord (B) is fastened to the system with a hook-and-loop fastener (A). If you are placing
the system in a service position after you disconnect the power cords, ensure that you unstrap the
fastener.
(L003)
or

or
or
or
DANGER: Multiple power cords. The product might be equipped with multiple AC power cords
or multiple DC power cables. To remove all hazardous voltages, disconnect all power cords
and power cables. (L003)
following figure.

10. Label and disconnect all of the cables or transceivers that are attached to the adapter you plan to
remove.
Use a hook-and-loop fastener to hold the cables in place.
Important: If you are disconnecting the SAS AZ cable which controls the internal disk bays, use extra
care when removing cables from the adapter connectors. Gently pull the blue tab straight back from
the system to release the latches that secure the SAS cable to the adapter. To prevent possible tab
breakage, do not pull the blue tab to the side; instead, pull the blue tab straight back. While gently
pulling the blue tab, unplug and remove the SAS cable from the adapter by pulling on the black SAS
cable itself. Do not apply extra pulling force on the blue tab to remove cable.
Attention:

Permanently removing an adapter from the 9040-MR9 system

To permanently remove an adapter from the system, complete the steps in this procedure.
Procedure


• To remove an adapter from a cassette that has adapter retainers and strips, continue with step “4”
on page 44.
• To remove an adapter from a cassette that doesn't have adapter retainers and strips, continue with
4. If your cassette has two adapter retainers and strips, complete the following steps to remove an
adapter from a cassette.
b) Remove the adapter retainers (B) by rotating them in the direction that is shown and moving them
all the way off the strips.
c) Open the cassette by pressing and sliding the release bar (C) in the direction that is shown.
d) Remove the adapter.
5. If your cassette doesn't have two adapter retainers and strips, complete the following steps to remove
the adapter from the cassette.
b) Open the cassette by pressing and sliding the release bar (B) in the direction that is shown.
c) Remove the adapter.

6. Place the removed adapter on an approved ESD surface.
7. After permanently removing an adapter, you must install a tailstock filler into the cassette to ensure
proper airflow.
a) Open the tailstock clamp (A) in the direction that is shown.
b) Insert the tailstock filler firmly into the tailstock retaining channel and ensure that it is seated.
c) Rotate the tailstock filler toward the front of the cassette and into place.
d) Put the adapter retainers (B) into the locked position by rotating them in the direction that is shown.
e) Close the tailstock clamp (A) by rotating the clamp in the direction that is shown.

Figure 32. Replacing an adapter in a cassette for the 9040-MR9 system
Attention:

Preparing the 9040-MR9 system for operation after permanently removing

an adapter
To prepare the system for operation after permanently removing anadapter, complete the steps in this
procedure.
Procedure
• If you completed the procedure with the system power turned off, continue with step “3” on page
47.
• If you completed the procedure with the system power turned on, continue with step “4” on page
48.
3. Using your labels, reconnect the power cords (A) to the system unit as shown in the following figure.
Fasten the power cords to the system by using the hook-and-loop fasteners (B) as shown in the
following figure.

Figure 34. Connecting the power cords

6. Start the system. For instructions, see Starting a system (www.ibm.com/support/knowledgecenter/
POWER9/p9haj/crustartsys.htm).
7. Place the removed adapter in a safe place.
Related procedures for installing and removing adapters

Find procedures that are related to installing and removing adapters.
Avoiding electric shock

Find information about precautions you should take to avoid electric shock when working on our around a
computer system.
DANGER: When working on or around the system, observe the following precautions:
Electrical voltage and current from power, telephone, and communication cables are hazardous. To
avoid a shock hazard: If IBM supplied the power cord(s), connect power to this unit only with the
IBM provided power cord. Do not use the IBM provided power cord for any other product. Do not
open or service any power supply assembly. Do not connect or disconnect any cables or perform
installation, maintenance, or reconfiguration of this product during an electrical storm.

• The product might be equipped with multiple power cords. To remove all hazardous
voltages, disconnect all power cords. For AC power, disconnect all power cords from their AC power
source. For racks with a DC power distribution panel (PDP), disconnect the customer’s DC power source
to the PDP.
• When connecting power to the product ensure all power cables are properly connected. For racks with
AC power, connect all power cords to a properly wired and grounded electrical outlet. Ensure that the
outlet supplies proper voltage and phase rotation according to the system rating plate. For racks with a
DC power distribution panel (PDP), connect the customer’s DC power source to the PDP. Ensure that the
proper polarity is used when attaching the DC power and DC power return wiring.
• Connect any equipment that will be attached to this product to properly wired outlets.
• When possible, use one hand only to connect or disconnect signal cables.
• Never turn on any equipment when there is evidence of fire, water, or structural damage.
• Do not attempt to switch on power to the machine until all possible unsafe conditions are corrected.
• When performing a machine inspection: Assume that an electrical safety hazard is present. Perform
all continuity, grounding, and power checks specified during the subsystem installation procedures to
ensure that the machine meets safety requirements. Do not attempt to switch power to the machine
until all possible unsafe conditions are corrected. Before you open the device covers, unless instructed
otherwise in the installation and configuration procedures: Disconnect the attached AC power cords,
turn off the applicable circuit breakers located in the rack power distribution panel (PDP), and
disconnect any telecommunications systems, networks, and modems.
• Connect and disconnect cables as described in the following procedures when installing, moving, or
opening covers on this product or attached devices.
To Disconnect: 1) Turn off everything (unless instructed otherwise). 2) For AC power, remove the power
cords from the outlets. 3) For racks with a DC power distribution panel (PDP), turn off the circuit
breakers located in the PDP and remove the power from the Customer's DC power source. 4) Remove
the signal cables from the connectors. 5) Remove all cables from the devices.
To Connect: 1) Turn off everything (unless instructed otherwise). 2) Attach all cables to the devices. 3)
Attach the signal cables to the connectors. 4) For AC power, attach the power cords to the outlets. 5)
For racks with a DC power distribution panel (PDP), restore the power from the Customer's DC power
source and turn on the circuit breakers located in the PDP. 6) Turn on the devices.
• Sharp edges, corners and joints may be present in and around the system. Use
care when handling equipment to avoid cuts, scrapes and pinching. (D005)
Handling static-sensitive devices

Find information about precautions you must take to prevent damage to electronic components from
static electricity discharge.
Electronic boards, adapters, media drives, and disk drives are sensitive to static electricity discharge.
These devices are wrapped in antistatic bags to prevent this damage. Take the following precautions to
prevent damage to these devices from static electricity discharge.
• Attach a wrist strap to an unpainted metal surface of your hardware to prevent electrostatic discharge
• When you are using a wrist strap, follow all electrical safety procedures. A wrist strap is for static
control. It does not increase or decrease your risk of receiving electric shock when you are using or
working on electrical equipment.
• If you do not have a wrist strap, before you remove the product from ESD packaging and installing or
replacing hardware, touch an unpainted metal surface of the system for a minimum of 5 seconds.
• Do not remove the device from the antistatic bag until you are ready to install the device in the system.

• With the device still in its antistatic bag, touch it to the metal frame of the system.
• Grasp cards and boards by the edges. Avoid touching the components and gold connectors on the
adapter.
• If you need to lay the device down while it is out of the antistatic bag, lay it on the antistatic bag. Before
you pick it up again, touch the antistatic bag and the metal frame of the system at the same time.
• Handle the devices carefully to prevent permanent damage.
Updating the worldwide port name for a new 5735 IOA

If you exchange a 5735 Fibre Channel input/output adapter (IOA), the IBM external storage subsystem
must be updated to use the worldwide port name (WWPN) of the new 5735 IOA. Any SAN hardware that
uses the WWPN zoning might also need updating.
For instructions on how to update the external storage subsystem or SAN hardware configurations, see
the documentation for those systems.
The WWPN for the Fibre Channel IOA can be found by using the Hardware Service Manager in SST or DST
to display details about the 5735 IOA Logical Hardware Resource information, and use the port worldwide
name field.
The 16-digit WWPN can also be determined by appending the digits 1000 to the beginning of the 12-digit
IEEE address that is found on the tailstock label of the Fibre Channel IO adapter.
Removing and replacing the tailstock on an adapter

Find information about removing and replacing the tailstock on an adapter. You can replace the tailstock
on an adapter if the adapter has a different tailstock.
Before you begin

You must have removed the adapter or the adapter filler from the system.
About this task

The tailstock for individual adapters can be either tall (high-profile) or short (low-profile). New systems
ship with the correct tailstock on the cards already installed. Through unique feature codes, a
miscellaneous equipment specification (MES) also ships with the correct sized tailstock. For repairs,
however, replacement parts usually ship with high-profile tailstock. If the failed adapter was a low-profile
adapter installed in the system, then you must exchange the tall tailstock that was shipped on the
replacement card with the low-profile tailstock from the failed card.
Note: A Phillips screwdriver is required to complete the procedure.
To remove and replace an adapter tailstock, choose from the following options:
• Removing the tailstock from a failed adapter or adapter filler
• Removing the tailstock from a new adapter
• Replacing the tailstock in a new adapter
Procedure
Removing the tailstock from a failed adapter or adapter filler
2. Using a Phillips screwdriver, unscrew the two screws (A) that attach the tailstock (B) to the adapter,
as shown in Figure 36 on page 52.

Figure 36. Removing the low-profile tailstock from an adapter
3. Detach the tailstock from the adapter and place the tailstock and the screws on a flat, static-
protective surface.
4. If you are removing the tailstock from a 4-Port 10/100/1000 Base-TX adapter, there is only one
screw to remove. After removing the screw, disengage the tabs from the card hardware and remove
the tailstock.
5. If you are removing the tailstock from an Ethernet or Fibre Channel adapter that has small form-
factor pluggable (SFP) transceivers, you must first remove the SFP transceivers.
To remove the SFP transceivers, complete the following steps:
a) Place the card flat on a static-protective surface.
b) Open the latch (A) by rotating it down and away from the card as shown in Figure 37 on page 53.
c) Slide the transceiver (B) out of the adapter hardware.
d) Repeat for the other transceiver.

Figure 37. Removing SFP transceivers from adapters
Removing the tailstock from a new adapter
8. Using a Phillips screwdriver, unscrew the two retaining screws (A) that attach the high-profile
tailstock (B) to the new adapter, as shown in Figure 38 on page 54.

Figure 38. Removing the high-profile tailstock from a new adapter
9. If the new adapter is a 4-Port 10/100/1000 Base-TX adapter, see “4” on page 52 for removing the
tailstock and then return here.
10. If the new adapter is an Ethernet or Fibre Channel adapter, see “5” on page 52 for removing the
tailstock and then return here.
11. Detach the tailstock from the new adapter and store the tailstock and its screws in the antistatic
package that the new adapter shipped in.
Replacing the tailstock in a new adapter
14. Using a Phillips screwdriver and the two retaining screws (B), attach the tailstock (A) from the failed
adapter onto the new adapter, as shown in Figure 39 on page 55.

Figure 39. Attaching the low-profile tailstock to an adapter
15. If the new adapter is a 4-Port 10/100/1000 Base-TX Express adapter, first engage the tailstock with
the tabs on the card hardware. After the tailstock is attached, secure the tailstock with its screw.
16. If the new adapter is an Ethernet or Fibre Channel adapter, you must attach the SFP transceivers
after you replace the tailstock.
To attach the SFP transceivers, complete the following steps:
a) Place the card flat on a static-protective surface.
b) Slide the transceiver (A) into the adapter hardware.
c) With the latch (B) in the open position, push the latch by rotating it up and toward the card as
shown in Figure 40 on page 56.
d) Repeat for the other transceiver.

Figure 40. Replacing SFP transceivers in the adapter
17. Put the failed adapter in the shipping material and return it.
What to do next
Return to the procedure that sent you here.
Hot-plug manager access for AIX

Find information about how to service adapters with the system power on in AIX.
The instructions for servicing adapters with the system power on in AIX refer you to these procedures
when it is appropriate to perform them.
Note: For an adapter to be serviced with the system power on, both the adapter and the system unit must
support hot-plug procedures. To identify adapters that are hot-pluggable in the system you are servicing,
refer to the following placement information: adapter placement.
Accessing the hot-plug management functions

Find information about how to use the hot-plug manager to service adapters with the system power
turned on in AIX.
About this task

Note: Procedures that are completed with the system power turned on also known as hot-plug
procedures. The hot-plug procedure for an adapter in an AIX system requires the system administrator
to take the adapter offline before starting the procedure. Before taking an adapter offline, the devices
attached to the adapter must be taken offline as well. This action prevents a service representative or
user from causing an unexpected outage for system users.
To access the hot-plug menus, complete the following steps:

Procedure
1. Log in as root user.
2. At the command line, type smitty.
3. Select Devices.
4. Select PCI Hot Plug Manager and press Enter.
The PCI Hot-Plug Manager menu displays.
For details about the menu options in the PCI Hot-Plug Manager screen, see “PCI hot-plug manager
menu” on page 57.
What to do next
Return to the procedure that directed you here.
PCI hot-plug manager menu

Find information about how to use the PCI Hot Plug Manager to service PCI adapters with the system
power on in AIX. The following options are available from the PCI Hot Plug Manager menu.
Note: For information about the PCI slot LED states, see “Component LEDs” on page 58.
Table 1. PCI Hot Plug Manager menu options

Menu option Description
List PCI hot-plug Provides a descriptive list of all slots that support PCI hot-plug capability. If the
slots listing for a slot indicates it holds an unknown device, select the Install/configure
Devices added after IPL to configure the adapter in that slot.
Add a PCI hot- Allows the user to add a new PCI hot-plug-capable adapter to the slot with the
plug adapter system turned on. You will be asked to identify the PCI slot that you have selected
prior to the actual operation. The selected PCI slot will go into the Action state and
finally into the On state.
Note: The system will indicate the slot holds an unknown device until you perform
the Install/configure devices added after IPL option to configure the adapter.
Replace/remove Allows the user to remove an existing adapter, or replace an existing adapter with an
a PCI hot-plug identical one. For this option to work, the adapter must be in the Defined state (see
adapter the "Unconfigure a Device" option). You will be asked to identify the PCI slot prior to
the actual operation. The selected PCI slot will go into the Action state.
Identify a PCI Allows the user to identify a PCI slot. The selected PCI slot will go into the Identify
hot-plug slot state. See “Component LEDs” on page 58.
Unconfigure a Allows the user to put an existing PCI adapter into the Defined state if the device is
device no longer in use.
This step must be completed successfully before starting any removal or
replacement operation. If this step fails, the customer must take action to release
the device.
Configure a Allows a new PCI adapter to be configured into the system if software support is
defined device already available for the adapter. The selected PCI slot will go into the On state.
Install/configure The system attempts to configure any new devices and tries to find and install any
devices added required software from a user-selected source.
after IPL

The add, remove, and replace functions return information to the user indicating whether the operation
was successful. If additional instructions are provided on the screen, complete the recommended actions.
If the instructions do not resolve the problem, do the following:
• If the adapter is listed as Unknown, perform the Install/configure devices Added After IPL option to
configure the adapter.
• If you receive a warning indicating that needed device packages are not installed, the system
administrator must install the specified packages before you can configure or diagnose the adapter.
• If you receive a failure message indicating a hardware error, the problem might be either the adapter or
the PCI slot. Isolate the problem by retrying the operation in a different PCI slot, or trying a different
adapter in the slot. If you determine that you have failing hardware, call your service representative.
• Do not use Install/configure devices added after IPL if your system is set up to run HACMP clustering.
Consult with your system administrator or software support to determine the correct method to
configure the replacement device.
Component LEDs
Individual LEDs are located on or near the failing components. Use the information in this section to
interpret the LEDs.
The LEDs are located either on the component itself or on the carrier of the component (for example,
memory card, fan, memory module, or processor). LEDs are either green or amber.
Green LEDs indicate either of the following:
• Electrical power is present.
• Activity is occurring on a link. (The system could be sending or receiving information.)
Amber LEDs indicate a fault or identify condition. If your system or one of the components on your system
has an amber LED turned on or flashing, identify the problem and take the appropriate action to restore
the system to normal.
Resetting the LEDs in AIX

Individual LEDs are located on or near the failing components. You can use this procedure to reset the
LEDs after you have completed a repair action.
About this task

After the repair action is complete, perform the following tasks:
Procedure
1. Log in as root user.
2. At the command line, type diag.
3. Select Task Selection.
4. Select Log Repair Action.
5. Select the device that was repaired.
6. Press F10 to exit diagnostics.
Results
If the Attention LED remains on after you have completed the repair action and reset the LEDs, call for
service support.

Installing the AIX device driver software
Find information about how to install the AIX device driver software for a PCIe adapter.
Before you begin

If you are installing the AIX operating system at this time, install the adapter before you install the
operating system. When you install the AIX operating system, the adapter device driver is automatically
installed and the following procedure does not apply to your situation.
About this task

If you are installing only the device driver for a PCIe adapter, perform these steps:
Procedure
1. Log in to the system unit as root user.
2. Insert the media containing the device driver software (for example, the CD) into the media device.
If your system does not have a CD-ROM drive, refer to your system documentation for performing a
Network Installation Management (NIM) installation.
3. Type the following command at the System Management Interface Tool (SMIT) fast path: smit
devinst.
Press Enter. The Install Additional Device Software window appears with INPUT device / directory
for software option highlighted.
4. Type the name of the input device that you are using, or press F4 to select the input device from a list.
Press Enter. The Install Additional Device Software window is shown with the SOFTWARE to
install option highlighted.
5. Press F4 to select List.
6. Type / to display the Find window.
7. Type the device package name, and press Enter.
The device driver software is shown.
8. Press F7 to select the highlighted device driver software, and press Enter.
The Install Additional Device Software window is displayed. The entry fields are automatically
updated.
Press Enter twice to confirm. The Command Status window is displayed.
• The message RUNNING is highlighted to indicate that the installation and configuration command is
in progress.
• When RUNNING changes to OK, scroll to the bottom of the page and locate the installation
summary.
• After a successful installation, SUCCESS is displayed in the Result column of the installation
summary at the bottom of the page.
9. Remove the installation media from the drive.
10. Press F10 to exit SMIT.
11. To verify that the device drives is installed, complete the following steps:
a) If necessary, log in as root user.
b) At the command line, type lslpp -l devices.xxxxxxxxxx where xxxxxxxxxx is the device
package name.
Press Enter.
The following example shows when the adapter device driver is installed.

File set Level State Description
Path: /usr/lib/objrepos 5.3.8.0 COMMITTED Adapter name software
devices.xxxxxxxxxx
Verify that the file sets are installed at the AIX version level you are running. Level 5.3.8.0 is
an example. If no data is displayed on your screen, the adapter device driver was not installed
correctly. Try reinstalling the driver.
Installing or replacing an adapter with the system power turned on in a

Virtual I/O Server
Find information about how to install or replace an adapter in the Virtual I/O Server logical partition.
Before you begin

The Virtual I/O Server includes a Hot Plug Manager that is similar to the Hot Plug Manager in the AIX
operating system. The Hot Plug Manager allows you to hot plug adapters into the system and then
activate them for the logical partition without having to reboot the system. Use the Hot Plug Manager
for adding, identifying, or replacing adapters in the system that are currently assigned to the Virtual I/O
Server.
Prerequisites:
• If you are installing a new adapter, an empty system slot must be assigned to the Virtual I/O Server
logical partition. This task can be done through dynamic logical partitioning (DLPAR) operations.
• If you are using a Hardware Management Console (HMC), you must also update the logical partition
profile of the Virtual I/O Server so that the new adapter is configured to the Virtual I/O Server after you
restart the system.
• If you are installing a new adapter, ensure that you have the software required to support the new
adapter and determine whether there are any existing PTF prerequisites to install. For information
about software prerequisites, see the IBM Prerequisite website (http://www-912.ibm.com/e_dir/
eServerPrereq.nsf).
About this task

Choose from the following tasks:
• “Installing an adapter” on page 60
• “Replacing an adapter” on page 61
• “Unconfiguring storage adapters” on page 61
• “Preparing the client logical partitions” on page 62
Installing an adapter
About this task

To install an adapter with the system power on in Virtual I/O Server, complete the following steps:
Procedure
1. From the Hot Plug Manager, select Add a PCIe Hot Plug Adapter, then press Enter.
The Add a Hot-Plug Adapter window is displayed.
2. Select the appropriate empty slot from those listed, and press Enter.
A fast-blinking amber LED located at the back of the server near the adapter indicates that the slot has
been identified.

3. Follow the instructions on the screen to install the adapter until the LED for the specified slot is set to
the Action state.
a. Set the adapter LED to the action state so that the indicator light for the adapter slot flashes
b. Physically install the adapter
c. Finish the adapter installation task in diagmenu.
4. Enter cfgdev to configure the device for the Virtual I/O Server.
Results
If you are installing a PCIe, Fibre Channel adapter, it is now ready to be attached to a SAN and have LUNs
assigned to the Virtual I/O Server for virtualization.
Replacing an adapter
Before you begin

Prerequisite: Before you can remove or replace a storage adapter, you must unconfigure that adapter.
See “Unconfiguring storage adapters” on page 61 for instructions.
About this task

To replace an adapter with the system power turned on in Virtual I/O Server, complete the following
steps:
Procedure
1. From the PCIe Hot Plug Manager, select Unconfigure a Device, then press Enter.
2. Press F4 (or Esc +4) to display the Device Names menu.
3. Select the adapter you are removing in the Device Names menu.
4. In the Keep Definition field, use the Tab key to answer Yes. In the Unconfigure Child Devices field,
use the Tab key again to answer YES, then press Enter.
5. Press Enter to verify the information on the ARE YOU SURE screen. Successful unconfiguration is
indicated by the OK message displayed next to the Command field at the top of the screen.
6. Press F4 (or Esc +4) twice to return to the Hot Plug Manager.
7. Select replace/remove PCIe Hot Plug adapter.
8. Select the slot that has the device to be removed from the system.
9. Select replace.
A fast-blinking amber LED located at the back of the machine near the adapter indicates that the slot
has been identified.
10. Press Enter which places the adapter in the action state, meaning it is ready to be removed from the
system.
Unconfiguring storage adapters
About this task

Before you can remove or replace a storage adapter, you must unconfigure that adapter. Storage adapters
are generally parent devices to media devices, such as disk drives or tape drives. Removing the parent
requires that all attached child devices either be removed or placed in the define state.
Unconfiguring a storage adapter involves the following tasks:
• Closing all applications that are using the adapter you are removing, replacing, or moving
• Unmounting file systems

• Ensuring that all devices connected to the adapter are identified and stopped
• Listing all slots that are currently in use or a slot that is occupied by a specific adapter
• Identifying the adapter's slot location
• Making parent and child devices unavailable
• Making the adapter unavailable
If the adapter supports physical volumes that are in use by a client logical partition, then You can
perform steps on the client logical partition before unconfiguring the storage adapter. For instructions, see
“Preparing the client logical partitions” on page 62. For example, the adapter might be in use because
the physical volume was used to create a virtual target device, or it might be part of a volume group used
to create a virtual target device.
To unconfigure SCSI, SSA, and Fibre Channel storage adapters, complete the following steps:
Procedure
1. Connect to the Virtual I/O Server command-line interface.
2. Enter oem_setup_env to close all applications that are using the adapter you are unconfiguring.
3. Type lsslot-c PCI to list all the hot plug slots in the system unit and display their characteristics.
4. Type lsdev -C to list the current state of all the devices in the system unit.
5. Type unmount to unmount previously mounted file systems, directories, or files using this adapter.
6. Type rmdev -l adapter -R to make the adapter unavailable.
Attention: Do not use the -d flag with the rmdev command for hot plug operations because this
action removes your configuration.
Preparing the client logical partitions
About this task

If the virtual target devices of the client logical partitions are not available, the client logical partitions
can fail or they might be unable to perform I/O operations for a particular application. If you use the
HMC to manage the system, you might have redundant Virtual I/O Server logical partitions, which allow
for Virtual I/O Server maintenance and avoid downtime for client logical partitions. If you are replacing
an adapter on the Virtual I/O Server and your client logical partition is dependent on one or more of the
physical volumes accessed by that adapter, then You can take action on the client before you unconfigure
the adapter.
The virtual target devices must be in the define state before the Virtual I/O Server adapter can be
replaced. Do not remove the virtual devices permanently.
Procedure
To prepare the client logical partitions so that you can unconfigure an adapter, complete the following
steps depending on your situation.
Table 2. Situations and steps for preparing the client logical partitions
Situation Steps
You have redundant hardware on the Virtual I/O No action is required on the client logical partition.
Server for the adapter.
HMC-managed systems only: You have redundant No action is required on the client logical partition.
Virtual I/O Server logical partitions that, in However, path errors might be logged on the client
conjunction with virtual client adapters, provide logical partition.
multiple paths to the physical volume on the client
logical partition.

Table 2. Situations and steps for preparing the client logical partitions (continued)
Situation Steps
HMC-managed systems only: You have redundant See the procedures for your client operating
Virtual I/O Server logical partitions that, in system. For example, for AIX, see Replacing a
conjunction with virtual client adapters, provide disk on the Virtual I/O Server in the Advanced
multiple physical volumes that are used to mirror POWER Virtualization Best Practices Redpaper.
a volume group. The procedure for Linux is similar to this procedure
for AIX.For example, for AIX, see Replacing a
disk on the Virtual I/O Server in the Advanced
POWER Virtualization Best Practices Redpaper.
The procedure for Linux is similar to this procedure
for AIX.
You do not have redundant Virtual I/O Server Shut down the client logical partition.
logical partitions.
For systems that are managed
by the HMC, see Stopping a
system (www.ibm.com/support/knowledgecenter/
POWER9/p9haj/stopsyshmc.htm).
Verifying that the hot-plug adapter tools are installed for the Linux operating
system
Find information about how to verify that the hot-plug adapter tools are installed on your Linux system so
you can then verify the adapter is installed.
Before you begin

Note: The hot-plug adapter tools are not available for the 5105-22E system.
Procedure
1. Enter the following command to verify that the hot-plug adapter tools are installed: rpm -aq | grep
powerpc-utils.
If the command does not list any powerpc-utils packages, the Hot Plug tools are not installed.
2. Enter the following command to ensure that the rpaphp driver is loaded: ls -l /sys/bus/pci/
slots/
The directory should contain data.
• If the directory is empty, the driver is not loaded or the system does not contain hot-plug adapter
slots. The following is an example of the information displayed by this command:
drwxr-xr-x 15 root root 0 Feb 16 23:31 .

drwxr-xr-x 5 root root 0 Feb 16 23:31 ..
drwxr-xr-x 2 root root 0 Feb 16 23:31 0000:00:02.0
• If the directory does not exist, run the following command to mount the filesystem: mount -t
sysfs sysfs /sys
3. Ensure the following tools are available in the /usr/sbin directory.

• lsslot
• drmgr -c pci
4. Return to the procedure that sent you here.
Checking the amount of remaining life in NVMe devices

Learn how to use operating system commands to find the amount of remaining life in an NVMe device.
Using the operating system commands
The AIX, IBM i, and Linux operating systems have commands that you can use to determine the amount of
life that is remaining in an NVMe device.
Running the AIX command to check the amount of remaining life in NVMe
devices
Find information about using the AIX operating system to find the amount of remaining life in an NVMe
device.
About this task

To find the amount of remaining life in an NVMe device by using the AIX operating system, complete the
steps in this procedure.
Procedure
1. If the system has logical partitions, complete this procedure from the logical partition that owns the
NVMe device
2. To use the AIX operating system to find the remaining life on an NVMe device, complete the following
steps:
a) From the AIX command line, type diag and press Enter.
b) From the Function Selection menu, select Task Selection > NVMe general health information.
c) Select the NVMe device that you want to check remaining life for and press Enter.
d) View the Percentage of NVM subsystem life used field.
Is the value in the Percentage of NVM subsystem life used field 100%?
• Yes: Continue with the next step.
• No: Continue with step “4” on page 64.
3. The NVMe device is nearing its end of life and must be replaced. The NVMe device will soon reach
the limit for the number of write operations that are supported. Write operations to the NVMe device
become slower over time, and at some point the NVMe device becomes a read-only device. When
the operating system writes data to a read-only device, the write operations are rejected, and the
operating system considers the device as if a failure occurred. To support normal write operations, the
NVMe device must be replaced.
Note: Failure of IBM NVMe devices is covered in the standard warranty and during the maintenance
period only for devices that have not reached the maximum number of write cycles. Devices that reach
this limit might fail to operate according to specifications and must be replaced. This replacement cost
is not covered under the standard warranty or during the maintenance period.
This ends the procedure.
4. Does the Critical Warning field show Available spare space has fallen below threshold?
• No: A service action is not required. This ends the procedure.

operating system considers the device as if a failure occurred. To support normal write operations,
schedule maintenance to replace the NVMe device at your earliest convenience.
Running the Linux smart-log command to check the amount of remaining life
in NVMe devices
Find information about using the Linux operating system smart-log command to find the amount of
remaining life in an NVMe device.
About this task

To find the amount of remaining life in an NVMe device by using the Linux operating system smart-log
command, complete the steps in this procedure.
Procedure
1. If the system has logical partitions, complete this procedure from the logical partition that owns the
NVMe device
2. To use the Linux operating system to find the remaining life on an NVMe device, complete the following
steps:
a) From the Linux command line, type the following command and press Enter.
nvme smart-log /dev/nvmeX -H
where nvmeX is the resource name of the NVMe device.

b) View the Percentage used field.
Is the value in the Percentage used field 100%?
operating system considers the device as if a failure occurred. To support normal write operations, the
NVMe device must be replaced.
4. In the critical_warning portion of the command output, is the Available Spare field displayed?
5. Is the Available Spare field equal to 1?
• Yes: The NVMe device has low spares. Continue with step “7” on page 66.

6. Complete the following steps to determine if the NVMe device has low spares:
a) View the critical_warning field.
b) The critical_warning field is a hexadecimal number. Convert the hexadecimal number to a binary
number.
c) Is the rightmost digit of the binary number equal to 1?
• Yes: The NVMe device has low spares. Continue with the next step.
operating system considers the device as if a failure occurred. To support normal write operations,
schedule maintenance to replace the NVMe device at your earliest convenience.

Notices
This information was developed for products and services offered in the US.
IBM may not offer the products, services, or features discussed in this document in other countries.
Consult your local IBM representative for information on the products and services currently available in
your area. Any reference to an IBM product, program, or service is not intended to state or imply that
only that IBM product, program, or service may be used. Any functionally equivalent product, program, or
service that does not infringe any IBM intellectual property right may be used instead. However, it is the
user's responsibility to evaluate and verify the operation of any non-IBM product, program, or service.
IBM may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not grant you any license to these patents. You can
send license inquiries, in writing, to:
IBM Director of Licensing

IBM Corporation
North Castle Drive, MD-NC119
Armonk, NY 10504-1785
US
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION "AS IS"
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in
certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
Any references in this information to non-IBM websites are provided for convenience only and do not in
any manner serve as an endorsement of those websites. The materials at those websites are not part of
the materials for this IBM product and use of those websites is at your own risk.
IBM may use or distribute any of the information you provide in any way it believes appropriate without
incurring any obligation to you.
The performance data and client examples cited are presented for illustrative purposes only. Actual
performance results may vary depending on specific configurations and operating conditions.
Information concerning non-IBM products was obtained from the suppliers of those products, their
published announcements or other publicly available sources. IBM has not tested those products and
cannot confirm the accuracy of performance, compatibility or any other claims related to non-IBM
products. Questions on the capabilities of non-IBM products should be addressed to the suppliers of
those products.
Statements regarding IBM's future direction or intent are subject to change or withdrawal without notice,
and represent goals and objectives only.
All IBM prices shown are IBM's suggested retail prices, are current and are subject to change without
notice. Dealer prices may vary.
This information is for planning purposes only. The information herein is subject to change before the
products described become available.
This information contains examples of data and reports used in daily business operations. To illustrate
them as completely as possible, the examples include the names of individuals, companies, brands, and
products. All of these names are fictitious and any similarity to actual people or business enterprises is
entirely coincidental.
© Copyright IBM Corp. 2018, 2021 67

If you are viewing this information in softcopy, the photographs and color illustrations may not appear.
The drawings and specifications contained herein shall not be reproduced in whole or in part without the
written permission of IBM.
IBM has prepared this information for use with the specific machines indicated. IBM makes no
representations that it is suitable for any other purpose.
IBM's computer systems contain mechanisms designed to reduce the possibility of undetected data
corruption or loss. This risk, however, cannot be eliminated. Users who experience unplanned outages,
system failures, power fluctuations or outages, or component failures must verify the accuracy of
operations performed and data saved or transmitted by the system at or near the time of the outage or
failure. In addition, users must establish procedures to ensure that there is independent data verification
before relying on such data in sensitive or critical operations. Users should periodically check IBM's
support websites for updated information and fixes applicable to the system and related software.
Homologation statement
This product may not be certified in your country for connection by any means whatsoever to interfaces
of public telecommunications networks. Further certification may be required by law prior to making any
such connection. Contact an IBM representative or reseller for any questions.
Accessibility features for IBM Power Systems servers

Accessibility features assist users who have a disability, such as restricted mobility or limited vision, to
use information technology content successfully.
Overview
The IBM Power Systems servers include the following major accessibility features:
• Keyboard-only operation
• Operations that use a screen reader
The IBM Power Systems servers use the latest W3C Standard, WAI-ARIA 1.0 (www.w3.org/TR/wai-
aria/), to ensure compliance with US Section 508 (www.access-board.gov/guidelines-and-standards/
communications-and-it/about-the-section-508-standards/section-508-standards) and Web Content
Accessibility Guidelines (WCAG) 2.0 (www.w3.org/TR/WCAG20/). To take advantage of accessibility
features, use the latest release of your screen reader and the latest web browser that is supported by the
IBM Power Systems servers.
The IBM Power Systems servers online product documentation in IBM Knowledge Center is
enabled for accessibility. The accessibility features of IBM Knowledge Center are described in the
Accessibility section of the IBM Knowledge Center help (www.ibm.com/support/knowledgecenter/doc/
kc_help.html#accessibility).
Keyboard navigation
This product uses standard navigation keys.
Interface information
The IBM Power Systems servers user interfaces do not have content that flashes 2 - 55 times per second.
The IBM Power Systems servers web user interface relies on cascading style sheets to render content
properly and to provide a usable experience. The application provides an equivalent way for low-vision
users to use system display settings, including high-contrast mode. You can control font size by using the
device or web browser settings.
The IBM Power Systems servers web user interface includes WAI-ARIA navigational landmarks that you
can use to quickly navigate to functional areas in the application.

Vendor software
The IBM Power Systems servers include certain vendor software that is not covered under the IBM
license agreement. IBM makes no representation about the accessibility features of these products.
Contact the vendor for accessibility information about its products.
Related accessibility information

In addition to standard IBM help desk and support websites, IBM has a TTY telephone service for use by
deaf or hard of hearing customers to access sales and support services:
TTY service
800-IBM-3383 (800-426-3383)
(within North America)
For more information about the commitment that IBM has to accessibility, see IBM Accessibility
(www.ibm.com/able).
Privacy policy considerations

IBM Software products, including software as a service solutions, (“Software Offerings”) may use cookies
or other technologies to collect product usage information, to help improve the end user experience,
to tailor interactions with the end user, or for other purposes. In many cases no personally identifiable
information is collected by the Software Offerings. Some of our Software Offerings can help enable you
to collect personally identifiable information. If this Software Offering uses cookies to collect personally
identifiable information, specific information about this offering’s use of cookies is set forth below.
This Software Offering does not use cookies or other technologies to collect personally identifiable
information.
If the configurations deployed for this Software Offering provide you as the customer the ability to collect
personally identifiable information from end users via cookies and other technologies, you should seek
your own legal advice about any laws applicable to such data collection, including any requirements for
notice and consent.
For more information about the use of various technologies, including cookies, for these purposes,
see IBM’s Privacy Policy at http://www.ibm.com/privacy and IBM’s Online Privacy Statement at
http://www.ibm.com/privacy/details/us/en/ in the section entitled “Cookies, Web Beacons and Other
Technologies”.
Trademarks
IBM, the IBM logo, and ibm.com® are trademarks or registered trademarks of International Business
Machines Corp., registered in many jurisdictions worldwide. Other product and service names might be
trademarks of IBM or other companies. A current list of IBM trademarks is available on the web at
Copyright and trademark information.
The registered trademark Linux is used pursuant to a sublicense from the Linux Foundation, the exclusive
licensee of Linus Torvalds, owner of the mark on a worldwide basis.
Electronic emission notices

Class A Notices
The following Class A statements apply to the IBM servers that contain the POWER9 processor and its
features unless designated as electromagnetic compatibility (EMC) Class B in the feature information.
When attaching a monitor to the equipment, you must use the designated monitor cable and any
interference suppression devices supplied with the monitor.
Notices 69
Canada Notice
CAN ICES-3 (A)/NMB-3(A)
European Community and Morocco Notice

This product is in conformity with the protection requirements of Directive 2014/30/EU of the European
Parliament and of the Council on the harmonization of the laws of the Member States relating to
electromagnetic compatibility. IBM cannot accept responsibility for any failure to satisfy the protection
requirements resulting from a non-recommended modification of the product, including the fitting of
non-IBM option cards.
This product may cause interference if used in residential areas. Such use must be avoided unless the
user takes special measures to reduce electromagnetic emissions to prevent interference to the reception
of radio and television broadcasts.
Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment this
equipment may cause radio interference.
Germany Notice
Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse A EU-Richtlinie zur
Elektromagnetischen Verträglichkeit
Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2014/30/EU zur Angleichung der
Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-Mitgliedsstaatenund hält die
Grenzwerte der EN 55022 / EN 55032 Klasse A ein.
Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und
zu betreiben. Des Weiteren dürfen auch nur von der IBM empfohlene Kabel angeschlossen werden.
IBM übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt
ohne Zustimmung von IBM verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne
Empfehlung von IBM gesteckt/eingebaut werden.
EN 55032 Klasse A Geräte müssen mit folgendem Warnhinweis versehen werden:
"Warnung: Dieses ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich Funk-
Störungen verursachen; in diesem Fall kann vom Betreiber verlangt werden, angemessene Maßnahmen
zu ergreifen und dafür aufzukommen."
Deutschland: Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit von Geräten
Dieses Produkt entspricht dem “Gesetz über die elektromagnetische Verträglichkeit von Geräten (EMVG)“.
Dies ist die Umsetzung der EU-Richtlinie 2014/30/EU in der Bundesrepublik Deutschland.
Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit
von Geräten (EMVG) (bzw. der EMC Richtlinie 2014/30/EU) für Geräte der Klasse A
Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen -
CE - zu führen.
Verantwortlich für die Einhaltung der EMV Vorschriften ist der Hersteller:
International Business Machines Corp.
New Orchard Road
Armonk, New York 10504
Tel: 914-499-1900
Der verantwortliche Ansprechpartner des Herstellers in der EU ist:

IBM Deutschland GmbH
Technical Relations Europe, Abteilung M456
IBM-Allee 1, 71139 Ehningen, Germany
Tel: +49 (0) 800 225 5426
email: [email protected]

Generelle Informationen:
Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 / EN 55032 Klasse A.
Japan Electronics and Information Technology Industries Association (JEITA)

Notice
This statement applies to products less than or equal to 20 A per phase.
This statement applies to products greater than 20 A, single phase.
This statement applies to products greater than 20 A per phase, three-phase.
Japan Voluntary Control Council for Interference (VCCI) Notice
Korea Notice
Notices 71
People's Republic of China Notice
Russia Notice
Taiwan Notice
IBM Taiwan Contact Information:
United States Federal Communications Commission (FCC) Notice

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission
limits. Proper cables and connectors are available from IBM-authorized dealers. IBM is not responsible
for any radio or television interference caused by using other than recommended cables and connectors
or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications
could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Responsible Party:
International Business Machines Corporation
New Orchard Road
Armonk, NY 10504
Contact for FCC compliance information only: [email protected]
Class B Notices
The following Class B statements apply to features designated as electromagnetic compatibility (EMC)
Class B in the feature installation information.
When attaching a monitor to the equipment, you must use the designated monitor cable and any
interference suppression devices supplied with the monitor.
Canada Notice
CAN ICES-3 (B)/NMB-3(B)
European Community and Morocco Notice

This product is in conformity with the protection requirements of Directive 2014/30/EU of the European
Parliament and of the Council on the harmonization of the laws of the Member States relating to
electromagnetic compatibility. IBM cannot accept responsibility for any failure to satisfy the protection
requirements resulting from a non-recommended modification of the product, including the fitting of
non-IBM option cards.
German Notice
Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse B EU-Richtlinie zur
Elektromagnetischen Verträglichkeit
Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2014/30/EU zur Angleichung der
Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-Mitgliedsstaatenund hält die
Grenzwerte der EN 55022/ EN 55032 Klasse B ein.
Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und
zu betreiben. Des Weiteren dürfen auch nur von der IBM empfohlene Kabel angeschlossen werden.
IBM übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt
ohne Zustimmung von IBM verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne
Empfehlung von IBM gesteckt/eingebaut werden.
Deutschland: Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit von Geräten
Dieses Produkt entspricht dem “Gesetz über die elektromagnetische Verträglichkeit von Geräten (EMVG)“.
Dies ist die Umsetzung der EU-Richtlinie 2014/30/EU in der Bundesrepublik Deutschland.
Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit
von Geräten (EMVG) (bzw. der EMC Richtlinie 2014/30/EU) für Geräte der Klasse B
Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen -
CE - zu führen.
Verantwortlich für die Einhaltung der EMV Vorschriften ist der Hersteller:
International Business Machines Corp.
New Orchard Road
Tel: 914-499-1900
Der verantwortliche Ansprechpartner des Herstellers in der EU ist:

IBM Deutschland GmbH
Technical Relations Europe, Abteilung M456
IBM-Allee 1, 71139 Ehningen, Germany
Notices 73
Tel: +49 (0) 800 225 5426
email: [email protected]
Generelle Informationen:
Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55032 Klasse B
Japan Electronics and Information Technology Industries Association (JEITA)

Notice
This statement applies to products less than or equal to 20 A per phase.
This statement applies to products greater than 20 A, single phase.
This statement applies to products greater than 20 A per phase, three-phase.
Japan Voluntary Control Council for Interference (VCCI) Notice

Taiwan Notice
United States Federal Communications Commission (FCC) Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult an IBM-authorized dealer or service representative for help.
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission
limits. Proper cables and connectors are available from IBM-authorized dealers. IBM is not responsible
for any radio or television interference caused by using other than recommended cables and connectors
or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications
could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Responsible Party:
International Business Machines Corporation

New Orchard Road
Contact for FCC compliance information only: [email protected]
Terms and conditions

Permissions for the use of these publications are granted subject to the following terms and conditions.
Applicability: These terms and conditions are in addition to any terms of use for the IBM website.
Personal Use: You may reproduce these publications for your personal, noncommercial use provided that
all proprietary notices are preserved. You may not distribute, display or make derivative works of these
publications, or any portion thereof, without the express consent of IBM.
Commercial Use: You may reproduce, distribute and display these publications solely within your
enterprise provided that all proprietary notices are preserved. You may not make derivative works of
these publications, or reproduce, distribute or display these publications or any portion thereof outside
your enterprise, without the express consent of IBM.
Rights: Except as expressly granted in this permission, no other permissions, licenses or rights are
granted, either express or implied, to the publications or any information, data, software or other
intellectual property contained therein.
Notices 75
IBM reserves the right to withdraw the permissions granted herein whenever, in its discretion, the use
of the publications is detrimental to its interest or, as determined by IBM, the above instructions are not
being properly followed.
You may not download, export or re-export this information except in full compliance with all applicable
laws and regulations, including all United States export laws and regulations.
IBM MAKES NO GUARANTEE ABOUT THE CONTENT OF THESE PUBLICATIONS. THE PUBLICATIONS
ARE PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT,
AND FITNESS FOR A PARTICULAR PURPOSE.

IBM®

P9hak 950

Uploaded by

Copyright:

Available Formats

P9hak 950

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

P9hak 950

Uploaded by

Copyright:

Available Formats

Power Systems

Adapters for the 9040-MR9

Installing, removing, and replacing adapters..........................................................1

World Trade safety information

German safety information

Laser safety information

© Copyright IBM Corp. 2018, 2021 v

vi Power Systems: Adapters for the 9040-MR9

Safety notices vii

viii Power Systems: Adapters for the 9040-MR9

CAUTION: A hot surface nearby. (L007)

CAUTION: Hazardous moving parts nearby. (L008)

x Power Systems: Adapters for the 9040-MR9

Power and cabling information for NEBS (Network Equipment-Building System)

xii Power Systems: Adapters for the 9040-MR9

Safety notices xiii

Installing adapters in the 9040-MR9 system

About this task

Preparing the 9040-MR9 system to install an adapter

Before you begin

© Copyright IBM Corp. 2018, 2021 1

2 Power Systems: Adapters for the 9040-MR9

Installing, removing, and replacing adapters in the 9040-MR9 system 3

Figure 2. Removing the power cords

4 Power Systems: Adapters for the 9040-MR9

Installing, removing, and replacing adapters in the 9040-MR9 system 5

# Slot Description Device(s)

drmgr -c pci -a -s locationcode

6 Power Systems: Adapters for the 9040-MR9

Installing, removing, and replacing adapters in the 9040-MR9 system 7

8 Power Systems: Adapters for the 9040-MR9

Figure 4. Removing an adapter cassette from the 9040-MR9 system

Installing, removing, and replacing adapters in the 9040-MR9 system 9

10 Power Systems: Adapters for the 9040-MR9

Installing, removing, and replacing adapters in the 9040-MR9 system 11

12 Power Systems: Adapters for the 9040-MR9

Installing, removing, and replacing adapters in the 9040-MR9 system 13

14 Power Systems: Adapters for the 9040-MR9

Preparing the 9040-MR9 system for operation after installing an adapter

Installing, removing, and replacing adapters in the 9040-MR9 system 15

16 Power Systems: Adapters for the 9040-MR9

Installing, removing, and replacing adapters in the 9040-MR9 system 17

# Slot Description Device(s)

12. Verify the installed part.

Removing and replacing an adapter in the 9040-MR9 system

About this task

Preparing the 9040-MR9 system to remove and replace an adapter

Before you begin

18 Power Systems: Adapters for the 9040-MR9

About this task

Installing, removing, and replacing adapters in the 9040-MR9 system 19

20 Power Systems: Adapters for the 9040-MR9

Figure 14. Removing the power cords

Installing, removing, and replacing adapters in the 9040-MR9 system 21

22 Power Systems: Adapters for the 9040-MR9

Installing, removing, and replacing adapters in the 9040-MR9 system 23

Figure 15. Releasing the mounting bracket

24 Power Systems: Adapters for the 9040-MR9

drmgr -c pci -r -s locationcode