Scribd
Upload
6 views2 pages

BEE Assignment - 03

Uploaded by

sachin8948653245
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
6 views2 pages

BEE Assignment - 03

Uploaded by

sachin8948653245
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Nothing is inpossible os the word ilicf says LMPOSSIBLE (Dr.

AseemChandel)
Assipument-DC Circuit (Unit-1)
1) Define and Comnpare
(a) Active and Passive Elemcnts
(b) Unilateral & Bilateral Elemcnts
2) Determine the current in 28 2 resistor in thecircuit
shown in Fig. 2
3) Fig.3 shows two batteries conneoted in parallel each represented by an eml along with its internal
resistance. Aload resistance of 602 is connected across thc ends of batteries. Calculate the current
through each battery and the load.
4) Find the value of resistance R and the current ly in Fig,4 when the branch AD carries no current.
5) Find all the nodevoltages and the current in resistances 0.2502 and 1/302. Using nodal analysis. Fig.5
6) Deternmine V, using nodal analysis. Fig.6
7) Determine the nodal voltagcs and current through22 resistance. Using nodal analysis Fig,7
8) Analyze the circuit of Fig.8 by the mnesh using analysis incthod. From the result, calculate the current
in the 52 resistance
9) Write the nodal cquations in terms of node datum voltages V, and V. Solve for V, and V.. Hence.
find: Fig.9
() Direction and magnitude of current through 52 resistance.
(1) Power output/input to the current and voltage sources.
10) Using mesh analysis, find currents I,. 1h and I, in the circuit of Fig 10. Also find the power supplicd
by the two current sources.

7A()sa

(iq-7)

(iq-s)
S)2n-(Oty ww

(Ga-9

DOI: 03-01-2023
DOS :09-01-2023
Nothing is inpossible us the svrd tels)s: " MPOSSIBLE (Dr. Aseem Chandel)
Subject Code- BEE101
Assignment- 3(Unit-3)
1) Definethe following terms in reference to magnctic
circuit
) MMF ()Magnetic field Inteltsily (ii) Flux Intensity (iv) Reluctance (v)
Permeability
2) An iron ring of mcan length 50cnm. and relative permcability 300 has an air gap of
lmm. If the ring is
provide with a winding of 200 turns and acurrent ofIA is allowed to flow through, find the flux density.
3) Acoil of insulated wire of 500 turns and of resistance 4 ohms is closely wound on
iron ring. The ring has a
mean diameter of 25m and a uifom cross-sectional area of 700 mm. Calculate the total flux in the ring
when a de supply of 6Vis applied to the ends of the winding, Assume a relative permeability of 550.
4) An iron ring made up of three parts. Il, =12cm, a,- 6em'; I; =l0cm, as - Sem', l,-Bem, a, = 4cm.It is
surrounded by a coil of 200 turns, Dcterminc the exciting current required to create a flux of 0.5 m wb in
the iron ring. (Given
-2670, u3 1055, u3 =680).
5) Explain the working the principle & drive the E.M.F. cqn. of single phase transformer.
6) Explain the different types of losses in single phasc transformer and show that the cfficicncy off
transformer will be maximum if the fixed losses are cqual to variable losses.
7) 30KVA 2000/100 v single phase 50 Hz transformer has a primary resistance of 3.5 ohm and reactance of
4.5 ohm. The secondary resistance and reactance are 0.015, 0.2 respectively. Find.
() Equivalentresistancc, reactance and impedance as referred to primary side,
(i) Total copper loss in transformme
Ans: 5 ohm, 6.5 ohm, 8.2 ohm, 1.125W
8) In a 25 KVA 2000/200 Vtransformer, the iron and copper losses are 250 watts and 400 watts respectively.
Calculate the efficiency at full load and 0.8 power factor lagging determine the maximum efficiency and
the corresponding load. Ans: 97.1,23.38 kVA
9) A5kVA 440/220 Vsingle-phase tansformer has aprimary and secondary winding resistance of 2Qand
0.8 2 respectively. The primary and secondary reactances are 100Q and 1.52 respectively. Find the
secondary terminalvoltage at full load, 0.8 p.f. lagging.
10) Define voltageregulation. A transformer has 4% resistance and 6% reactance drop. Find the voltage
regulation at full load (a) 0.8p.f. lagging (b) 0:8p.f. leading and (c) unity p.f.:

DOI: 09/02/2023
DOS: 20/02/2023

You might also like