Solutions Inc.

UN-5700 Line

The DFCI UN-5700 Line stud has a special four-lead thread that operates in less than one turn.

The receptacle provides a friction lock by expanding against a surrounding coil spring as the

stud is engaged.

Rated locking torque is maintained over thousands of use cycles. These features are

combined with the advantages of standard threaded fasteners; panel take-up, no sheet

separation under load, and high tensile and shear ratings.

DFCI ® is a registered trademark of DFCI Solutions, Inc. UN-1

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 UN-5700 Line Solutions Inc.

The fastener stud has a fast four lead

thread, and is easily captivated in the panel

Studs
with a grommet that is slipped over the
threaded end and flattened down. Studs are
made of steel, head treated and cadmium
plated per QQ-P-416, Type 1, Class 3.
Other materials are available on special
order.

Retainers

The retaining rings are made of steel

cadmium plated per QQ-P-416, Type II,
Class 2.

Two types of receptacles are available—

rigid and floating (the latter for use where
Receptacles

misalignment may develop). The receptacle

is slotted and spring encircled. As the stud is
screwed into the receptacle, the spring is
expanded, thus creating a constricting force
on the stud. The receptacle is made of
aluminum alloy, anodized, and the spring is
made of music wire, cadmium plated per
QQ-P-416, Type II, Class 2. Spacers for all
floating receptacles are made of steel,
cadmium plated per QQ-P-416, Type II,
Class 2. Other materials are available on
special order.

UN-2 DFCI ® is a registered trademark of DFCI Solutions, Inc.

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 Solutions Inc.
UN-5700 Line
Components
Oval Head, Flush Head, Flush Head,
Hex Head Straight Slot Hex Recess
Type 578x-20
Straight Slot
Type 576x-20 Type 576x-S20
Type 571x-20
(Sizes 4, 5) (Size 3)

Studs are available with Hex, Oval-Slotted, and Flush-Slotted Heads. Available on special order: Oval Head Studs with
Phillips Recess.
Thread Major Diameter Rated Tensile Locking Torque
Locking Torque
Size and Shear Retention
(inch) (mm) (in.-lb.)
(lb.) (cycles)
3 .188 4.78 4-8 600 5,000
4 .250 6.35 8-12 1,000 5,000
4 .313 7.95 15-25 1,500 5,000

Retaining Ring
Type 5723-A and 5725-166-C3Y (for size 3)

Retaining Rings are slipped around the Stud and squeezed closed with pliers.
Rigid Receptacle Floating Receptacle Press Fit Receptacle
Types 5718 and 5718-A Types 5718-F and 5718-FA Type 5718-FP

Press-in receptacles are installed by

Rigid receptacles are riveted solidly to Floating receptacles have oversize
pressing into a round hole.
their support. Type 5718-A is used for rivet holes that permit movement
Receptacles float to accept panel
Size 3 and 4 studs. Type 5718 is used around rivet spacers within the holes.
misalignment. Type 5718-FP is
for size 5 studs only. Supplied with 2 spacers.
available for size 3 and 4 studs.

DFCI ® is a registered trademark of DFCI Solutions, Inc. UN-3

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 UN-5700 Line Solutions Inc.

Selection Procedure
1. Verify that the Mechanical Properties are suitable for the application.
2. Select a stud head style. For example: A size 3 Oval Head Stud would be 5713-20
3. Select a stud retainer and part number. Example: The Retaining Ring would be 5725-166-C3Y
4. Calculate the Total Material Thickness as described below.
5. Using the table on the stud page, find the Total Material Thickness range that applies to your
calculated Total Material Thickness. The G needed for the Stud Part Number is stated to the
right of the applicable Total Material Thickness range. For example: For the size 3 with a Total
Material Thickness of .175” (4.45 mm), the G needed would be -20.
6. Combine the stud head style and G for a complete part number. For example: The complete
part number for our example would be 5713-20-20-C2C.
7. Select either a rigid or floating receptacle. For example: The size 3 rigid receptacle is 5718-
A3-ACNC.
Finding the Total Material Thickness (TMT)
The Total Material Thickness (TMT) is the sum of the panel thickness, support thickness, and any
gap thickness that may be present. The panel thickness is the thickness of the material that contains
the stud. Support thickness is the thickness of the material to which the receptacle is mounted. Gap
thickness is the thickness of any gasket, spacing, or other material that prevents the panel and
support from being in direct contact with each other. All stud retainers drop into the support area and
do not add a gap.

UN-4 DFCI ® is a registered trademark of DFCI Solutions, Inc.

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 Solutions Inc.
UN-5700 Line
This page intentionally blank.

DFCI ® is a registered trademark of DFCI Solutions, Inc. UN-5

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 UN-5700 Line Solutions Inc.

Size 3 Studs
Flush Head, Hex Recess
Part Number: 5763-S20

Flush Head Oval Head Hex Head

Type 5763-S20 Type 5713-20 Type 5783-20
Oval Head, Straight Slot
These size 3 hex, oval and flush head studs are Part Number 5713-20
supplied with 3/16” (4.78 mm) thread major diameter.

The locking torque is 4 to 8 inch pounds, 600 pound

rated tensile and shear.

Stud Material: Steel, heat treated, cadmium plated per

QQ-P-416, Type 1, Class 3.

Typical Assembly Hex Head

Add your panel and support thickness to give you the Total Material Part Number 5783-20
Thickness. Then select the stud from the table on the next page.
(See page UN-4 for a complete description of Total Material
Thickness.)

UN-6 DFCI ® is a registered trademark of DFCI Solutions, Inc.

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 Solutions Inc.
UN-5700 Line
Size 3 Sizing Tables
(inch)
Stud Weight
Stud Shank Dimensions
Total Material (Lb. Each)
G
Thickness Flush Oval Hex
G DIM U DIM
5763-S20 5713-20 5783-20
.000” to .050” -5 .420” .160” -- .00304 .0060
.051” to .100” -10 .470” .210” -- .00324 .0062
.101” to .150” -15 .520” .260” .00308 .00344 .0064
.151” to .200” -20 .570” .310” .00328 .00364 .0066
.201” to .250” -25 .620” .360” .00348 .00384 .0068
.251” to .300” -30 .670” .410” .00368 .00404 .0070
.301” to .350” -35 .720” .460” .00388 .00424 .0072
.351” to .400” -40 .770” .510” .00408 .00444 .0074
Note: A thread lubricant suitable for the fastener’s installed environment is recommended.
For part number 5763-S20-15, a minimum panel thickness of .125” is required.

(mm)
Stud Weight
Stud Shank Dimensions
Total Material (Lb. Each)
G
Thickness Flush Oval Hex
G DIM U DIM
5763-S20 5713-20 5783-20
1.00 – 1.27 -5 10.67 1.06 -- .00304 .0060
1.30 – 2.54 -10 11.94 5.33 -- .00324 .0062
2.57 – 3.81 -15 13.21 6.60 .00308 .00344 .0064
3.84 – 5.08 -20 14.48 7.87 .00328 .00364 .0066
5.11 – 6.35 -25 15.75 9.14 .00348 .00384 .0068
6.38 – 7.62 -30 17.02 10.41 .00368 .00404 .0070
7.65 – 8.89 -35 18.29 10.92 .00388 .00424 .0072
8.92 – 10.16 -40 19.56 12.95 .00408 .00444 .0074
Note: A thread lubricant suitable for the fastener’s installed environment is recommended.
For part number 5763-S20-15, a minimum panel thickness of 3.18 mm is required.

DFCI ® is a registered trademark of DFCI Solutions, Inc. UN-7

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 UN-5700 Line Solutions Inc.

Size 3
Stud Retainers
Retaining Ring

Retaining Ring
Part Number 5725-166-C3Y
Material: Steel, cadmium plated with yellow chromate, per QQ-P-416, Type II, Class 2
Weight: .00025 lb.

UN-8 DFCI ® is a registered trademark of DFCI Solutions, Inc.

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 Solutions Inc.
UN-5700 Line
Size 3
Receptacles
Rigid Receptacle Floating Receptacle
For use with all size 3 studs For use with all size 3 studs

5718-A3
Rigid Receptacle

Part Number 5718-A3 Part Number 5718-FA3

Material: Aluminum alloy, anodized. Material: Aluminum alloy, anodized.
Spring: music wire cadmium plated per QQ-P-416, Spring: music wire cadmium plated per QQ-P-416,
Type II, Class 2 yellow Type II, Class 2, yellow
Weight: .0026 lb. Weight: .0033 lb. (including 2 spacers)
Float: .025 (.64 mm) all directions
5718-FA3 Press Fit Receptacle Spacer
Floating Support Thickness: For use with 5718-FA3 receptacle
Receptacle .050” (1.27 mm) min. 2 supplied with each 5718-FA3 receptacle
w/Spacers

5718-FP3 Part Number: 5718-FP3 Part Number: 5718-F3-3-C3Y

Press Fit Material: Ring: carbon spring steel, heat treated. Material: Steel, cadmium plated QQ-P-416, Type II,
Receptacle Retainer: steel, heat treated. Spring: music wire. Ring, Class 2 yellow chromate
retainer and spring – cadmium plated QQ-P-416, Weight: See Floating Receptacle above
Type II, Class 2, yellow chromate. Base: aluminum
alloy, anodized
Weight: .00577 lb.
Float: .015 (.38 mm) all directions

DFCI ® is a registered trademark of DFCI Solutions, Inc. UN-9

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 UN-5700 Line Solutions Inc.

Size 4 Studs
Flush Head, Straight Slot
Part Number: 5764-20

Flush Head Oval Head Hex Head

Type 5764-20 Type 5714-20 Type 5784-20
Oval Head, Straight Slot
These size 4 hex and oval head studs are supplied with ¼” Part Number 5714-20
(6.35 mm) thread major diameter.

The locking torque is 8 to 12 inch pounds. 1,000 pound

rated tensile and shear.

Stud Material: Steel, heat-treated, Cadmium plate per QQ-

P-416 Type I, Class 3.

Typical Assembly Hex Head

Add your panel and support thickness to give you the Total Material Part Number 5784-20
Thickness. Then select the stud from the table on the next page.
(See page UN-4 for a complete description of Total Material Thickness.)

UN-10 DFCI ® is a registered trademark of DFCI Solutions, Inc.

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 Solutions Inc.
UN-5700 Line
Size 4 Sizing Tables
(inch)
Stud Weight
Stud Shank Dimensions
Total Material (Lb. Each)
G
Thickness Flush Oval Hex
G DIM U DIM
5764-20 5714-20 5784-20
.000” to .100” -10 .565” .250” -- .00675 .01392
.101” to .200” -20 .665” .350” .00751 .00752 .01469
.201” to .300” -30 .765” .450” .00828 .00829 .01546
.301” to .400” -40 .865” .550” .00906 .00906 .01623
.401” to .500” -50 .965” .650” .00983 .00983 .01700
.501” to .600” -60 1.065” .750” .01060 .01060 .01777
.601” to .700” -70 1.165” .850” .01137 .01137 .01854
.701” to .800” -80 1.265” .950” .01214 .01214 .01931
Note: A thread lubricant suitable for the fastener’s installed environment is recommended.
For part number 5764-20-20-C2C, a minimum panel thickness of .150” is required.

(mm)
Stud Weight
Stud Shank Dimensions
Total Material (Lb. Each)
G
Thickness Flush Oval Hex
G DIM U DIM
5764-20 5714-20 5784-20
0.00 – 2.54 -10 14.35 6.35 -- .00675 .01392
2.57 – 5.08 -20 16.89 8.89 .00751 .00752 .01469
5.11 – 7.62 -30 19.43 11.43 .00828 .00829 .01546
7.65 – 10.16 -40 21.97 13.97 .00906 .00906 .01623
10.19 – 12.70 -50 24.51 16.51 .00983 .00983 .01700
12.73 – 15.24 -60 27.05 19.05 .01060 .01060 .01777
15.27 – 17.78 -70 29.59 21.59 .01137 .01137 .01854
17.81 – 20.32 -80 32.13 24.13 .01214 .01214 .01931
Note: A thread lubricant suitable for the fastener’s installed environment is recommended.
For part number 5764-20-20-C2C, a minimum panel thickness of 3.81 mm is required.

DFCI ® is a registered trademark of DFCI Solutions, Inc. UN-11

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 UN-5700 Line Solutions Inc.

Size 4
Stud Retainers
Retaining Ring

Retaining Ring
Part Number 5723-A514-C3Y
Material: Steel, cadmium plated with yellow chromate, per QQ-P-416, Type II, Class 2
Weight: .00042 lb.

UN-12 DFCI ® is a registered trademark of DFCI Solutions, Inc.

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 Solutions Inc.
UN-5700 Line
Size 4
Receptacles
Rigid Receptacle Floating Receptacle
For use with all size 4 studs For use with all size 4 studs

5718-A4-ACNC
Rigid Receptacle
Part Number 5718-A4-ACNC Part Number 5718-FA4-ACNC
Material: Aluminum alloy, anodized. Material: Aluminum alloy, anodized.
Spring: music wire cadmium plated per QQ-P-416, Spring: music wire cadmium plated per QQ-
Type II, Class 2 yellow P-416, Type II, Class 2, yellow
Weight: .00516 lb. Weight: .00593 lb. (including 2 spacers)
Float: .025 all directions
Press Fit Spacer
Support Thickness: For use with
.065” (1.65 mm) min. 5718-FA4-ACNC receptacle
5718-FA4-ACNC 2 supplied with each
Floating Receptacle 5718-FA4-ACNC receptacle
w/Spacers

5718-FP4-ACNC Part Number: 5718-FP4-ACNC Part Number: 5718-F4-3-C3Y

Material: Ring: carbon spring steel, heat treated. Material: Steel, cadmium plated QQ-P-416,
Press Fit Receptacle Retainer: steel, heat treated. Spring: music wire. Type II, Class 2 yellow chromate
Ring, retainer and spring – cadmium plated QQ-P- Weight: See Floating Receptacle above
416, Type II, Class 2, yellow chromate. Base:
aluminum alloy, anodized
Weight: .01156 lb.
Float: .015” (.38 mm) all directions

DFCI ® is a registered trademark of DFCI Solutions, Inc. UN-13

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 UN-5700 Line Solutions Inc.

Size 5 Studs
Flush Head, Straight Slot
Part Number: 5765-20

Flush Head Oval Head Hex Head

Type 5765-20 Type 5715-20 Type 5785-20
Oval Head, Straight Slot
These size 5 hex, oval and flush head studs are supplied Part Number 5715-20
with 5/16” (7.95 mm) thread major diameter.

The locking torque is 15 to 32 inch-pounds. 1,500 pound

rated tensile and shear.

Stud Material: steel, heat treated, cadmium plated per QQ-

P-416, Type 1, Class 3.

Typical Assembly Hex Head

Add your panel and support thickness to give you the Total Material Part Number 5785-20
Thickness. Then select the stud from the table on the next page.
(See page UN-4 for a complete description of Total Material Thickness.)

UN-14 DFCI ® is a registered trademark of DFCI Solutions, Inc.

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 Solutions Inc.
UN-5700 Line
Size 5 Sizing Tables
(inch)
Stud Weight
Stud Shank Dimensions
Total Material (Lb. Each)
G
Thickness Flush Oval Hex
G DIM U DIM
5765-20 5715-20 5785-20
.000” to .100” -10 .700” .360” .01311 .01335 .02555
.101” to .200” -20 .800” .460” .01443 .01467 .02687
.201” to .300” -30 .900” .560” .01575 .01599 .02819
.301” to .400” -40 1.000” .660” .01707 .01731 .02951
.401” to .500” -50 1.100” .760” .01839 .01863 .03083
.501” to .600” -60 1.200” .860” .01971 .01995 .03215
.601” to .700” -70 1.300” .960” .02103 .02127 .03479
.701” to .800” -80 1.400” 1.060” .02235 .02259 .03611
Note: A thread lubricant suitable for the fastener’s installed environment is recommended.

(mm)
Stud Weight
Stud Shank Dimensions
Total Material (Lb. Each)
G
Thickness Flush Oval Hex
G DIM U DIM
5765-20 5715-20 5785-20
0.00 – 2.54 -10 17.78 9.14 .01311 .01335 .02555
2.57 – 5.08 -20 20.32 11.68 .01443 .01467 .02687
5.11 – 7.62 -30 22.86 14.22 .01575 .01599 .02819
7.65 – 10.16 -40 25.40 16.76 .01707 .01731 .02951
10.19 – 12.70 -50 27.94 19.30 .01839 .01863 .03083
12.73 – 15.24 -60 30.48 21.84 .01971 .01995 .03215
15.27 – 17.78 -70 33.02 24.38 .02103 .02127 .03479
17.81 – 20.32 -80 35.56 26.92 .02235 .02259 .03611
Note: A thread lubricant suitable for the fastener’s installed environment is recommended.

DFCI ® is a registered trademark of DFCI Solutions, Inc. UN-15

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 UN-5700 Line Solutions Inc.

Size 5
Stud Retainers
Retaining Ring

Retaining Ring
Part Number 5723-A516-C3Y
Material: Steel, cadmium plated with yellow chromate, per QQ-P-416, Type II, Class 2
Weight: .00094 lb.

UN-16 DFCI ® is a registered trademark of DFCI Solutions, Inc.

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 Solutions Inc.
UN-5700 Line
Size 5
Receptacles
Rigid Receptacle Floating Receptacle
For use with all size 5 studs For use with all size 5 studs

Part Number 5718-5-ACNC Part Number 5718-F5-ACNC

Material: Aluminum alloy, anodized. Material: Aluminum alloy, anodized.
5718-5-ACNC Spring: music wire cadmium plated per Spring: music wire cadmium plated per
Rigid Receptacle QQ-P-416, Type II, Class 2 yellow QQ-P-416, Type II, Class 2, yellow
Weight: .0092 lb. Weight: .01000 lb. (including 2 spacers)
Float: .037 all directions
Spacer
For use with 5718-F5-ACNC receptacle
2 supplied with each
5718-F5-ACNC receptacle

5718-F5-ACNC
Floating Receptacle
w/Spacers

Part Number: 5718-F5-3-C3Y

Material: Steel, cadmium plated QQ-P-
416, Type II, Class 2 yellow chromate
Weight: See Floating Receptacle above

DFCI ® is a registered trademark of DFCI Solutions, Inc. UN-17

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 UN-5700 Line Solutions Inc.

Stud Installation
Retaining Ring
All Head Styles
1. Drill hole in panel 2. Insert stud and slip 3. Squeeze ring with pliers.
retaining ring over shank
of stud.

Hole Diameter
Stud Size
(inch) (mm)
3 3/16” 4.78
4 1/4” 6.35
5 5/16” 7.95

UN-18 DFCI ® is a registered trademark of DFCI Solutions, Inc.

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 Solutions Inc.
UN-5700 Line
This page intentionally blank.

DFCI ® is a registered trademark of DFCI Solutions, Inc. UN-19

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 UN-5700 Line Solutions Inc.

Receptacle Installation
Rigid and Floating Rigid
1. Drill holes and countersink rivet holes of 2. Rivet receptacle
support panel
(inch)
Stud A K
J
Size ±.010 ±.005
3 .344 .625 .096
4 .468 .750 .096
5 .703 1.000 .128
(mm)
Stud A K
J
Size ±0.25 ±0.13
3 8.74 15.88 2.44
4 11.89 19.05 2.44
Floating
5 17.86 25.40 3.25
2. Insert spacers and rivet receptacle

UN-20 DFCI ® is a registered trademark of DFCI Solutions, Inc.

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 Solutions Inc.
UN-5700 Line
Receptacle Installation
Press Fit
Type GH grommets may be used to retain studs when the support thickness exceeds .070” (1.78 mm) for 5718-FP3 and
.094” (2.39 mm) for 5718-FP4 receptacles. For thinner supports, the retaining ring must be used. The retaining ring should
be slipped around stud shaft and closed with pliers in undercut section of stud.
1. Drill hole 2. Make a press in tool using 3. Press in.
dimensions shown below

Hole Diameter
Size
(inch) (mm)
+.003 +.08
3 .406 10.31
-.001 -.03
+.003 +.08
4 .500 12.70
-.001 -.03

Tool Dimensions
+.005 (0.13 mm)
Part Number W X Y Z
-.000 (0.00 mm)
(inch) (mm) (inch) (mm) (inch) (mm) (inch) (mm)
5718-FP3 .344 x .625 deep 9.58 x 15.88 deep .625 15.88 .505 12.88 .125 3.18
5718-FP4 .453 x .625 deep 11.51 x 15.88 deep .750 19.05 .630 16.00 .156 3.96

DFCI ® is a registered trademark of DFCI Solutions, Inc. UN-21

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.
 UN-5700 Line Solutions Inc.

This page intentionally blank.

UN-22 DFCI ® is a registered trademark of DFCI Solutions, Inc.

Copyright © 2002-2005 by DFCI Solutions, Inc. All rights reserved.