〈161〉 Medical Devices-Bacterial Endotoxin and Pyrogen Tests

Printed on: Wed Feb 08 2023, 11:05:11 PM(EST) Status: Currently Official on 09-Feb-2023 DocId: GUID-3553FBAE-2484-4850-ACC0-ECF20BDF9C46_1_en-US
Printed by: Dang Van Vu Official Date: Official as of 01-Dec-2017 Document Type: GENERAL CHAPTER @2023 USPC
Do Not Distribute DOI Ref: hm55z DOI: https://doi.org/10.31003/USPNF_M98910_01_01
1
á161ñ MEDICAL DEVICES—BACTERIAL ENDOTOXIN AND PYROGEN

TESTS
INTRODUCTION
The methods and requirements in this chapter apply to assemblies or devices labeled sterile and nonpyrogenic that are in
contact directly or indirectly with the cardiovascular system, lymphatic system, or cerebrospinal fluid. This includes, but may
not be limited to, the following:
• Fluid pathways of catheters and administration sets such as solution administration sets, extension sets, transfer sets, blood
administration sets, intravenous catheters, implants, extracorporeal oxygenator tubing, dialysis tubing, intramuscular drug
delivery catheters, and transfusion and infusion assemblies
• Liquid medical devices such as dialysate
• Implantable medical devices such as heart valves and vascular grafts, and other medical devices with a nonpyrogenic claim
that may come into contact with blood or cerebrospinal fluid
• Gels with a nonpyrogenic claim including demineralized bone matrices and drug delivery systems
BACTERIAL ENDOTOXINS
al
For the bacterial endotoxins test (BET) assay parameters, procedures, standards, and controls for the gel-clot and kinetic and
endpoint assays, proceed as directed in Bacterial Endotoxins Test á85ñ, substituting the medical device eluate for the product
sample.
DEFINITIONS
Endotoxin limit
ci
• The endotoxin limit for the finished device is NMT 20 USP Endotoxin Units per device and NMT 2.15 USP Endotoxin Units
for devices in contact with cerebrospinal fluid.
ffi
• For devices that directly or indirectly contact the intraocular environment, a lower endotoxin limit may apply (1).
• The endotoxin limit for the device extract in Endotoxin Units/mL is calculated as:
Result = (K × N)/V
K = limit for each device
O
N = number of devices tested

V = total volume of the extract
Kit: A kit is defined as a collection of individual devices in its primary package, or a variety of related devices. Each individual
type of device may have its own product endotoxin limit and should be tested and evaluated on an individual basis; see Table
1. Selection of Product Units for Testing [refer to ANSI/AAMI ST72 (2)].
Table 1. Selection of Product Units for Testing

Product Unit Item for Testing
Individual medical device in a primary package where each
medical device is used individually in clinical practice Individual medical device
Set of components in a primary package where components are

assembled as a product and are used together in clinical practice Combination of components
A number of identical medical devices in one primary package where each

medical device is used independently in clinical practice Single medical device taken from the primary package
Kit of procedure-related medical devices where each medical device is used in-
dependently in clinical practice and where each medical device may have a Each type of medical device that has a nonpyrogenic claim, or
different endotoxin limit all items together
Lambda (λ): λ is the test method sensitivity for gel-clot methods. For turbidometric or chromogenic technique, λ is equal
to the lowest endotoxin concentration on the referenced standard curve.
Product families: Product families for the purposes of BET may be defined on the basis of common materials of
construction and/or common components. The choice of family members should be justified and documented. If a product
family contains devices of many sizes, the device with the largest surface area claimed to be nonpyrogenic is chosen as the
representative member of the family to be used in suitability testing.
Extracting or rinsing solution: Water for BET [see Bacterial Endotoxins Test á85ñ, Reagents and Test Solutions, Water
for Bacterial Endotoxins Test (BET)] or other suitable solvent demonstrated to be noninterfering with the BET assay is used to
extract or rinse the medical device.
https://online.uspnf.com/uspnf/document/1_GUID-3553FBAE-2484-4850-ACC0-ECF20BDF9C46_1_en-US 1/4
www.webofpharma.com
2
Sampling
1. Sample: A sample for end-product testing must be in its final configuration and packaging, including all component parts
that make up the final medical device.
2. Representative sampling: A representative sample is a sample plan that is created and justified based on the assumption
that the manufacturing process is validated and in a state of control.
3. Sample size: The number of devices chosen for routine testing is dependent on the size of the lot, level of control, statistical
considerations, and historical performance. In most cases, each lot of product must be tested using an appropriate
number of samples, NMT 10, taken at random to represent the quality of the lot. Alternate sampling plans that utilize
small sample sizes or do not test each lot of product must be clearly defined and must be supported/justified by a robust
risk assessment.
4. Pre-post sterilization samples: When qualifying a BET assay for pre-sterilization samples, equivalency in test results must
be shown with post-sterilization samples to ensure that sterilization and post-sterilization handling have no adverse
impact on the accuracy of the test result. Pre-sterilization testing is inappropriate for products that support microbial
growth.
Suitability testing (also known as test for interfering factors): Suitability studies of device extracts are
designed to ensure that the device extract under test does not adversely impact the accuracy of the test result by either a)
causing the assay to underestimate endotoxin (inhibition) or b) contributing to overestimation of endotoxin (enhancement).
REAGENTS AND TEST SOLUTIONS
al
See á85ñ.
PREREQUISITES TO TESTING
Apparatus
ci
All equipment used in the extraction or testing process must be properly qualified and/or calibrated as appropriate. This
equipment includes but is not limited to water baths, heat blocks, mechanical pipetters (fixed, adjustable, and repeating
pipetters), thermometers, and plate/tube/cartridge readers.
Depyrogenate all glassware and other heat-stable materials in a hot air oven using a validated process. If employing plastic
ffi
apparatus such as microplates and pipet tips for automatic pipetters, use apparatus that is shown to be free of detectable
endotoxin and does not interfere with the test.
Analysts must be properly trained to perform the assay.
The assay sensitivity must be confirmed as described in Bacterial Endotoxins Test á85ñ, Gel-Clot Technique, Preparatory Testing,
Test for Confirmation of Labeled Lysate Sensitivity for gel-clot reagents and Bacterial Endotoxins Test á85ñ, Photometric Quantitative
Techniques, Preparatory Testing, Assurance of Criteria for the Standard Curve for quantitative methods. Assay sensitivity
O
confirmation must be carried out when a new batch of reagent (lysate or endotoxin) is used or when there is any change in
the test conditions that could affect the outcome of the test.
PREPARATION OF DEVICES: STANDARD METHODS
Endotoxin Limit
The endotoxin limit for the extracting or rinsing solution is:
Result = (K × N)/V
K = amount of endotoxin allowed per device (20 Endotoxin Units per device; 2.15 for intrathecal devices)
N = number of devices tested
V = total volume of the extract or rinse
[NOTE—The volume of the rinse or extract may be adjusted for the size and configuration of the device.]
The standard extracting fluid for extracting, rinsing, or soaking medical devices is Water for BET. If necessary, other solvents
may be used after it has been demonstrated that they do not interfere with the performance of the assay. Extraction is not
required for liquid medical devices. Either the entire device if claimed to be nonpyrogenic or all components of the device that
are claimed to be nonpyrogenic, including fluid pathways, must come in contact with the extraction fluid for the entire course
of the extraction.
The standard extraction method is to soak or immerse the device or flush the fluid pathway with extracting fluid that has
been heated to 37 ± 1.0°, keeping the extracting fluid in contact with the relevant surface(s) for NLT 1 h at controlled room
temperature. Alternate extraction or rinsing methods may be used, but must be demonstrated to be equivalent to or better
than the standard method. Extracts from individual medical devices are typically pooled for testing.
www.webofpharma.com
3
Suitability
Suitability of the BET assay must be demonstrated for each product or product family. The number of batches of product
chosen for the suitability study is reflective of the level of control of the process and must be justified.
For the suitability test, medical device extracts or liquid medical devices are considered to be the sample solutions under test
and are tested as outlined for the chosen technique in Bacterial Endotoxins Test á85ñ, Gel-Clot Technique, Preparatory Testing, Test
for Interfering Factors.
If necessary, adjust the pH of the solution to be examined (or dilution thereof) so that the pH of the mixture of the lysate
and sample solution falls within the pH range specified by the lysate manufacturer, usually pH 6.0–8.0. The pH may be adjusted
by use of an acid, base, or suitable buffer as recommended by the lysate manufacturer. Acids and bases may be prepared from
concentrates or solids with Water for BET in containers free of detectable endotoxin. Buffers must be shown to be free of
detectable endotoxin and interfering factors.
If the undiluted rinsing or extracting solution or liquid medical device is determined to be unsuitable for á85ñ, the test for
interfering factors may be repeated utilizing dilution or a method that will neutralize or eliminate the interfering substance.
If glucan interference is suspected, the use of a glucan-blocking agent or endotoxin-specific lysate is permissible.
Dilution in Water for BET or other validated solvent by a factor not to exceed the maximum valid dilution (MVD) is permissible.
The MVD for medical devices is the following:
MVD = Endotoxin limit (of the rinsing, extracting, or diluting solution in Endotoxin Units/mL)/λ
λ = sensitivity of the test method in Endotoxin Units/mL
Interference may be overcome by suitable treatment of the device extract. Methods for overcoming interference and the
al
qualification of such treatments are described in á85ñ. To establish that the chosen treatment effectively eliminates interference
without loss of endotoxins, perform the assay described in á85ñ using the preparation to be examined to which standard
endotoxin has been added and which has then been submitted to the chosen treatment.
ci
DEMONSTRATION OF CONTINUED SUITABILITY
The continued suitability of the assay should be re-assessed when significant changes are made to the product, process, raw
material supply, manufacturing and/or testing site, BET reagent source, or any other change that could adversely affect the
accuracy of the BET result. The results of this re-assessment should be documented, and suitability studies re-executed as
ffi
necessary.
Changes to extraction techniques require a new suitability study. Because of possible changes in interference patterns
between standard BET methods, a change in BET methodology (e.g., from gel-clot limits test to kinetic chromogenic) requires a
re-execution of the suitability study.
Routine Testing
O
Routine testing of the finished medical devices must utilize the same extraction techniques that were documented in the
successful suitability study.
Routine testing is to be performed as outlined in á85ñ, following instructions for incubation and controls listed under the
chosen assay technique.
Interpretation of Test Results

See á85ñ. The preparation under test complies with the test if the mean endotoxin concentration of the replicates of Solution
A, after correction for dilution and concentration, is less than 20 Endotoxin Units per medical device (2.15 Endotoxin Units per
medical device for those devices that come in contact with the cerebrospinal fluid.) For liquid medical devices, the limit meets
the requirements set forth in Bacterial Endotoxins Test á85ñ, Determination of Maximum Valid Dilution (MVD), Endotoxin Limit,
footnote 2.
If a device fails to meet this requirement, an investigation may be initiated per documented procedures. A failed, valid BET
assay may not be repeated using Pyrogen Test á151ñ in its place.
PYROGENS
For samples that cannot be tested by BET because of nonremovable inhibition or enhancement of the test, á151ñ is applied.
Select an appropriate number of devices, NMT 10, and obtain a pooled extract utilizing preparation methods appropriate to
the device as directed for bacterial endotoxins, but with volumes of rinse or extraction fluid not to exceed 40 mL of sterile saline
test solution per device. The requirements of á151ñ must be met.
REFERENCES
1. U.S. Food and Drug Administration. Guidance for industry. Pyrogen and endotoxins testing: Questions and answers.
Rockville, MD: Food and Drug Administration; June 2012. www.fda.gov/Drugs/
GuidanceComplianceRegulatoryInformation/Guidances/ucm314718.htm. Accessed 12 July 2016.
www.webofpharma.com
4
2. ANSI/AAMI ST72. Bacterial endotoxins—Test methods, routine monitoring, and alternatives to batch testing. Arlington,
VA: Association for the Advancement of Medical Instrumentation; 2011.
al
ci
ffi
O
www.webofpharma.com

〈161〉 Medical Devices-Bacterial Endotoxin and Pyrogen Tests

Uploaded by

Copyright:

Available Formats

〈161〉 Medical Devices-Bacterial Endotoxin and Pyrogen Tests

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

〈161〉 Medical Devices-Bacterial Endotoxin and Pyrogen Tests

Uploaded by

Copyright:

Available Formats

Printed on: Wed Feb 08 2023, 11:05:11 PM(EST) Status: Currently Official on 09-Feb-2023 DocId: GUID-3553FBAE-2484-4850-ACC0-ECF20BDF9C46_1_en-US

á161ñ MEDICAL DEVICES—BACTERIAL ENDOTOXIN AND PYROGEN

N = number of devices tested

Table 1. Selection of Product Units for Testing

Set of components in a primary package where components are

A number of identical medical devices in one primary package where each

REAGENTS AND TEST SOLUTIONS

PREPARATION OF DEVICES: STANDARD METHODS

Interpretation of Test Results

You might also like