®

INA
137
INA
213
INA137
7
INA
137
INA
213
7
INA2137

AUDIO DIFFERENTIAL LINE RECEIVERS

±6dB (G = 1/2 or 2)
FEATURES APPLICATIONS
● SINGLE AND DUAL VERSIONS ● AUDIO DIFFERENTIAL LINE RECEIVER
● LOW DISTORTION: 0.0005% at f = 1kHz ● G = 1/2 OR G = 2 AMPLIFIER
● HIGH SLEW RATE: 14V/µs ● INSTRUMENTATION BUILDING BLOCK
● FAST SETTLING TIME: 3µs to 0.01% ● CURRENT SHUNT MONITOR
● WIDE SUPPLY RANGE: ±4V to ±18V ● VOLTAGE-CONTROLLED CURRENT
● LOW QUIESCENT CURRENT: 2.9mA max SOURCE
● HIGH CMRR: 90dB ● GROUND LOOP ELIMINATOR
● FIXED GAIN = ±6dB
V+

7
● PACKAGES—SINGLE: 8-PIN DIP, SO-8
DUAL: 14-PIN DIP, SO-14 2
12kΩ 6kΩ
5
–In Sense

DESCRIPTION
6
The INA137 and INA2137 are differential line receivers Output

consisting of high performance op amps with on-chip

precision resistors. They are fully specified for high 3
12kΩ 6kΩ
1
+In Ref
performance audio applications and have excellent ac
specifications, including low distortion (0.0005% at INA137
V+
1kHz) and high slew rate (14V/µs), assuring good 4

dynamic response. In addition, wide output voltage V– 11

swing and high output drive capability allow use in a
12kΩ 6kΩ
wide variety of demanding applications. The dual ver- –In A
2 12
Sense A
sion features completely independent circuitry for low-
est crosstalk and freedom from interaction, even when
13
overdriven or overloaded. A Out A

The INA137 and INA2137 on-chip resistors are laser

12kΩ 6kΩ
trimmed for accurate gain and optimum +In A
3 14
Ref A
common-mode rejection. Furthermore, excellent TCR
12kΩ 6kΩ
tracking of the resistors maintains gain accuracy and 6 10
–In B Sense B
common-mode rejection over temperature. Operation
is guaranteed from ±4V to ±18V (8V to 36V total
supply). 9
B Out B

The INA137 is available in 8-pin DIP and SO-8

surface-mount packages. The INA2137 comes in 12kΩ 6kΩ
5 8
+In B Ref B
14-pin DIP and SO-14 surface-mount packages. Both
INA2137
are specified for operation over the extended industrial
4
temperature range, –40°C to +85°C.
V–

International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111
Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132

©1997 Burr-Brown Corporation PDS-1391B Printed in U.S.A. July, 1997

SBOS072
SPECIFICATIONS: VS = ±18V
At TA = +25°C, VS = ±18V, RL = 2kΩ, G = 1/2, and Ref Pin connected to Ground, unless otherwise noted.

INA137PA, UA
INA2137PA, UA
PARAMETER CONDITIONS MIN TYP MAX UNITS

AUDIO PERFORMANCE
Total Harmonic Distortion + Noise, f = 1kHz VIN = 10Vrms 0.0005 %
Noise Floor, RTO(1) 20kHz BW –106 dBu
Headroom, RTO(1) THD+N < 1% +23 dBu
FREQUENCY RESPONSE
Small-Signal Bandwidth 4.0 MHz
Slew Rate 14 V/µs
Settling Time: 0.1% 10V Step, CL = 100pF 2 µs
0.01% 10V Step, CL = 100pF 3 µs
Overload Recovery Time 50% Overdrive 3 µs
Channel Separation (dual), f = 1kHz 123 dB
OUTPUT NOISE VOLTAGE(2)
f = 20Hz to 20kHz 3.5 µVrms
f = 1kHz 26 nV/√HZ
OFFSET VOLTAGE(3) RTO
Input Offset Voltage VCM = 0V ±100 ±1000 µV
vs Temperature Specified Temperature Range ±2 µV/°C
vs Power Supply VS = ±4V to ±18V ±5 ±60 µV/V
INPUT
Common-Mode Voltage Range: Positive VO = 0V 3(V+)–7.5 3(V+)–6 V
Negative VO = 0V 3(V–)+7.5 3(V–)+3 V
Differential Voltage Range See Typical Curve
Common-Mode Rejection VCM = ±46.5V, RS = 0Ω 74 90 dB
Impedance(4)
Differential 24 kΩ
Common-Mode 18 kΩ
GAIN
Initial 0.5 V/V
Error VO = –10V to 10V ±0.01 ±0.1 %
vs Temperature ±1 ±10 ppm/°C
Nonlinearity VO = –10V to 10V 0.0001 %
OUTPUT
Voltage Output, Positive (V+)–2 (V+)–1.8 V
Negative (V–)+2 (V–)+1.6 V
Current Limit, Continuous to Common ±60 mA
Capacitive Load (Stable Operation) 500 pF
POWER SUPPLY
Rated Voltage ±18 V
Voltage Range ±4 ±18 V
Quiescent Current (per Amplifier) IO = 0 ±2.4 ±2.9 mA
TEMPERATURE RANGE
Specification Range –40 85 °C
Operation Range –55 125 °C
Storage Range –55 125 °C
Thermal Resistance, θJA
8-Pin DIP 100 °C/W
SO-8 Surface-Mount 150 °C/W
14-Pin DIP 80 °C/W
SO-14 Surface-Mount 100 °C/W

RTO = Referred to Output.

NOTES: (1) dBu = 20log (Vrms /0.7746). (2) Includes effects of amplifier’s input current noise and thermal noise contribution of resistor network.
(3) Includes effects of amplifier’s input bias and offset currents. (4) Internal resistors are ratio matched but have ±25% absolute value.

The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.

INA137, INA2137 2
PIN CONFIGURATIONS
Top View 8-Pin DIP/SO-8 Top View 14-Pin DIP/SO-14

Ref 1 8 NC NC 1 14 Ref A

–In 2 7 V+ –In A 2 13 Out A

A

+In 3 6 Output +In A 3 12 Sense A

V– 4 5 Sense V– 4 11 V+

+In B 5 10 Sense B
NC = No Connection B

–In B 6 9 Out B

ABSOLUTE MAXIMUM RATINGS(1) NC 7 8 Ref B

Supply Voltage, V+ to V– .................................................................... 40V

Input Voltage Range .......................................................................... ±80V
Output Short-Circuit (to ground)(2) ............................................................ Continuous
Operating Temperature ................................................. –55°C to +125°C NC = No Connection
Storage Temperature ..................................................... –55°C to +125°C
Junction Temperature .................................................................... +150°C
Lead Temperature (soldering, 10s) ............................................... +300°C

NOTE: (1) Stresses above these ratings may cause permanent damage.
(2) One channel per package.
ELECTROSTATIC
DISCHARGE SENSITIVITY
PACKAGE/ORDERING INFORMATION
This integrated circuit can be damaged by ESD. Burr-Brown
PACKAGE SPECIFICATION recommends that all integrated circuits be handled with ap-
DRAWING TEMPERATURE
PRODUCT PACKAGE NUMBER(1) RANGE propriate precautions. Failure to observe proper handling and
Single
installation procedures can cause damage.
INA137PA 8-Pin DIP 006 –40°C to +85°C ESD damage can range from subtle performance degradation
INA137UA SO-8 Surface-Mount 182 –40°C to +85°C
to complete device failure. Precision integrated circuits may
Dual
INA2137PA 14-Pin DIP 010 –40°C to +85°C
be more susceptible to damage because very small parametric
INA2137UA SO-14 Surface-Mount 235 –40°C to +85°C changes could cause the device not to meet its published
NOTE: (1) For detailed drawing and dimension table, please see end of data
specifications.
sheet, or Appendix C of Burr-Brown IC Data Book.

3 INA137, INA2137
 TYPICAL PERFORMANCE CURVES
At TA = +25°C, VS = ±18V, and G = 1/2, unless otherwise noted.

TOTAL HARMONIC DISTORTION+NOISE DIM INTERMODULATION DISTORTION

vs FREQUENCY vs OUTPUT AMPLITUDE
0.1 5
BW = 100kHz
VO = 5Vrms
1
0.010 RTO
THD+Noise (%)

DIM (%)
0.1 RL = 2kΩ, 600Ω
RL = 100kΩ

0.001 RL = 2kΩ
0.010

RL = 600Ω
0.0001 0.001
20 100 1k 10k 20k –10 –5 0 5 10 15 20 25
Frequency (Hz) Output Amplitude (dBu)

HEADROOM - TOTAL HARMONIC DISTORTION+NOISE HARMONIC DISTORTION PRODUCTS

vs OUTPUT AMPLITUDE vs FREQUENCY
1 0.001
VO = 1Vrms RL = 2kΩ
f = 1kHz
Amplitude (% of Fundamental)

RL = 600Ω
0.1
0.0001 2nd Harmonic
RTO
THD+Noise (%)

0.010 3rd Harmonic

RL = 600Ω
RL = 2kΩ
0.00001
RL = 600Ω
0.001
RL = 2kΩ,
100kΩ ( Noise Limited)

0.0001 0.000001
0 5 10 15 20 25 30 20 100 1k 10k 20k
Output Amplitude (dBu) Frequency (Hz)

OUTPUT VOLTAGE NOISE SPECTRAL DENSITY OUTPUT NOISE VOLTAGE

vs FREQUENCY vs NOISE BANDWIDTH
10k 100
Voltage Noise (nV/√Hz)

Noise Voltage (µVrms)

1k 10

100 1

10 0.1
1 10 100 1k 10k 100k 1M 1 10 100 1k 10k 100k
Frequency (Hz) Frequency (Hz)

INA137, INA2137 4
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±18V, and G = 1/2, unless otherwise noted.

GAIN vs FREQUENCY COMMON-MODE REJECTION vs FREQUENCY

10 100

Common-Mode Rejection (dB)

0
Voltage Gain (dB)

80

–10

60
–20

RTO

–30 40
1k 10k 100k 1M 10M 1k 10k 100k 1M
Frequency (Hz) Frequency (Hz)

POWER SUPPLY REJECTION vs FREQUENCY CHANNEL SEPARATION vs FREQUENCY

120 130
RTO RL = 100kΩ

100
Power Supply Rejection (dB)

Channel Separation (dB)

120
80 RL = 2kΩ
–PSR

60 110

40
+PSR 100
20
Dual Devices
0 90
100 1k 10k 100k 1M 20 100 1k 10k 20k
Frequency (Hz) Frequency (Hz)

INPUT COMMON-MODE VOLTAGE

MAXIMUM OUTPUT VOLTAGE vs FREQUENCY vs OUTPUT VOLTAGE
40 80
G = 1/2
60 VS = ±18V
Common-Mode Voltage (V)

30 40
Output Voltage (Vp-p)

20

20 0

–20

10 –40

–60 VREF = 0V
RL = 2kΩ
0 –80
100 1k 10k 100k 1M 10M –20 –15 –10 –5 0 5 10 15 20
Frequency (Hz) Output Voltage (V)

5 INA137, INA2137
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±18V, and G = 1/2, unless otherwise noted.

QUIESCENT CURRENT vs TEMPERATURE SLEW RATE vs TEMPERATURE

4 16

–SR
Quiescent Current (mA)

3 14
+SR

Slew Rate (V/µs)

2 12

1 10

0 8
–75 –50 –25 0 25 50 75 100 125 –75 –50 –25 0 25 50 75 100 125
Temperature (°C) Temperature (°C)

SHORT-CIRCUIT CURRENT vs TEMPERATURE QUIESCENT CURRENT vs SUPPLY VOLTAGE

80 3

60
Short-Circuit Current (mA)

Quiescent Current (mA)

40
+ISC
2
20

–20
–ISC 1
–40

–60

–80 0
–75 –50 –25 0 25 50 75 100 125 ±4 ±6 ±8 ±10 ±12 ±14 ±16 ±18
Temperature (°C) Supply Voltage (V)

OFFSET VOLTAGE OFFSET VOLTAGE DRIFT

PRODUCTION DISTRIBUTION PRODUCTION DISTRIBUTION
35 30
Typical Production Distribution
Typical Production
30 of Packaged Units.
Distribution of 25
Packaged Units.
Percent of Amplifiers (%)
Percent of Amplifiers (%)

25
20
20
15
15
10
10

5 5

0 0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
–1000
–900
–800
–700
–600
–500
–400
–300
–200
–100
0
100
200
300
400
500
600
700
800
900
1000

Offset Voltage (µV) Offset Voltage Drift (µV/°C)

INA137, INA2137 6
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±18V, and G = 1/2, unless otherwise noted.

SMALL-SIGNAL OVERSHOOT
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT vs LOAD CAPACITANCE
17 70
16 –55°C
60
15
Output Voltage Swing (V)

25°C
14 50
125°C
13

Overshoot (%)
85°C
12 40

–12 30
85°C
–13 125°C
–14 20
–15 RL = 2kΩ
25°C 10
–16 –55°C 100mV Step
–17 0
0 ±20 ±40 ±60 ±80 0 200 400 600 800 1000 1200
Output Current (mA) Load Capacitance (pF)

LARGE-SIGNAL STEP RESPONSE

CL = 100pF
SMALL-SIGNAL STEP RESPONSE

CL = 100pF
50mV/div

5V/div

CL = 500pF

1µs/div 1µs/div

7 INA137, INA2137
APPLICATIONS INFORMATION The INA137 and INA2137 have excellent distortion charac-
teristics. THD+Noise is below 0.001% throughout the audio
The INA137 and INA2137 are differential line receivers frequency range. Up to approximately 10kHz distortion is
suitable for a wide range of audio and general-purpose below the measurement limit of commonly used test equip-
applications. Figure 1 shows the basic G = 1/2 (–6dB) ment. Furthermore, distortion remains relatively flat over its
differential receiver configuration. The input and feedback wide output voltage swing range (approximately 1.7V from
resistors can be reversed to achieve G = 2 (+6dB), as shown either supply).
in Figure 2. For applications requiring G = 1 (0dB), the
INA134 and INA2134 are recommended.
OFFSET VOLTAGE TRIM
Decoupling capacitors are strongly recommended for appli-
The INA137 and INA2137 are laser trimmed for low offset
cations with noisy or high impedance power supplies. The
voltage and drift. Most applications require no external offset
capacitors should be placed close to the device pins as
adjustment. Figure 3 shows an optional circuit for trimming
shown in Figure 1. All circuitry is completely independent
the output offset voltage. The output is referred to the output
in the dual version assuring lowest crosstalk and normal
reference terminal (pin 1), which is normally grounded. A
behavior when one amplifier is overdriven or short-cir-
voltage applied to the Ref terminal will be summed with the
cuited.
output signal. This can be used to null offset voltage as
As shown in Figure 1, the differential input signal is con- shown in Figure 3. The source impedance of a signal applied
nected to pins 2 and 3. The source impedances connected to to the Ref terminal should be less than 10Ω to maintain good
the inputs must be nearly equal to assure good common- common-mode rejection.
mode rejection. A 5Ω mismatch in source impedance will
degrade the common-mode rejection of a typical device to
approximately 77dB (RTO). If the source has a known
impedance mismatch, an additional resistor in series with INA137

the opposite input can be used to preserve good common- R2 R1

–In
mode rejection. V2
5 2

6kΩ 12kΩ

V– V+ 6

1µF 1µF VO = 2 (V3 – V2)

R4 R3
4 7 +In 3
1
V3
INA137
6kΩ 12kΩ
R1 R2
–In
2 5
V2
12kΩ 6kΩ FIGURE 2. G = 2 Differential Receiver.

VO = 1/2 (V3 – V2) G = 1/2

INA137
R3 R4 R1 R2
+In 1 12kΩ 6kΩ
3
V3 2 5
V2
12kΩ 6kΩ

6
VO
FIGURE 1. G = 1/2 Differential Receiver (Basic Power
Supply and Signal Connections). R3
20Ω 12kΩ
3
V3
AUDIO PERFORMANCE
R4
The INA137 and INA2137 were designed for enhanced ac 6kΩ
performance. Very low distortion, low noise, and wide band- +15V

width provide superior performance in high quality audio 1

VO = 1/2 (V3 – V2) 250kΩ
applications. Laser-trimmed matched resistors provide opti- Offset Adjustment 100kΩ
mum common-mode rejection (typically 90dB), especially Range = ±1mV
when compared to circuits implemented with an op amp 10Ω
and discrete precision resistors. In addition, high slew rate
–15V
(14V/µs) and fast settling time (3µs to 0.01%) ensure excel-
lent dynamic performance.
FIGURE 3. Offset Adjustment.
®

INA137, INA2137 8
 INA137
G=2 INA137
6kΩ 12kΩ
2 5 V1
6kΩ 12kΩ
–In 1/2 2 5
OPA2134

6
6kΩ V0 = 2V1 + V2 R2
1
V1

12kΩ
V2 6
3 R1
V0
R2
0utput

FIGURE 4. Precision Summing Amplifier.

6kΩ 12kΩ
1/2 3 1
V2 OPA2134

INA137 +In
12kΩ 6kΩ
2 5
–In VO = 2 (1 + 2R2/R1) (V2 –V1)

6 3 6
BUF634 VO FIGURE 6. High Input Impedance Instrumentation Amplifier.

12kΩ 6kΩ
3 1
+In

FIGURE 5. Boosting Output Current.

The difference amplifier is a highly versatile building • Precision Voltage-to-Current Converter with Differential
block that is useful in a wide variety of applications. See Inputs
the INA105 data sheet for additional applications ideas, • Differential Input Voltage-to-Current Converter for Low
including: IOUT
• Current Receiver with Compliance to Rails • Isolating Current Source
• ±10V Precision Voltage Reference • Differential Output Difference Amplifier
• ±5V Precision Voltage Reference • Isolating Current Source with Buffering Amplifier for
• Precision Average Value Amplifier Greater Accuracy
• Precision Bipolar Offsetting • Window Comparator with Window Span and Window
Center Inputs
• Precision Summing Amplifier with Gain
• Precision Voltage-Controlled Current Source with Buff-
• Instrumentation Amplifier Guard Drive Generator
ered Differential Inputs and Gain
• Precision Summing Instrumentation Amplifier
• Precision Absolute Value Buffer

9 INA137, INA2137
 PACKAGE OPTION ADDENDUM

www.ti.com 27-Jun-2024

PACKAGING INFORMATION

Orderable Device Status Package Type Package Pins Package Eco Plan Lead finish/ MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) Ball material (3) (4/5)
(6)

INA137UA ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-3-260C-168 HR -40 to 85 INA Samples
137UA
INA137UA/2K5 ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-3-260C-168 HR -40 to 85 INA Samples
137UA
INA2137PA ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 INA2137PA Samples

INA2137UA ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-3-260C-168 HR INA2137UA Samples

INA2137UA/2K5 ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-3-260C-168 HR INA2137UA Samples

INA2137UAE4 ACTIVE SOIC D 14 50 TBD Call TI Call TI Samples

(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.

(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.

(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.

Addendum-Page 1
 PACKAGE OPTION ADDENDUM

www.ti.com 27-Jun-2024

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

Addendum-Page 2
 PACKAGE MATERIALS INFORMATION

www.ti.com 25-Sep-2024

TAPE AND REEL INFORMATION

REEL DIMENSIONS TAPE DIMENSIONS

K0 P1

B0 W
Reel
Diameter
Cavity A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
W Overall width of the carrier tape
P1 Pitch between successive cavity centers

Reel Width (W1)

QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE

Sprocket Holes

Q1 Q2 Q1 Q2

Q3 Q4 Q3 Q4 User Direction of Feed

Pocket Quadrants

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
INA137UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
INA2137UA/2K5 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 25-Sep-2024

TAPE AND REEL BOX DIMENSIONS

Width (mm)
H
W

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
INA137UA/2K5 SOIC D 8 2500 356.0 356.0 35.0
INA2137UA/2K5 SOIC D 14 2500 356.0 356.0 35.0

Pack Materials-Page 2
 PACKAGE MATERIALS INFORMATION

www.ti.com 25-Sep-2024

TUBE

T - Tube
height L - Tube length

W - Tube
width

B - Alignment groove width

*All dimensions are nominal

Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm)
INA137UA D SOIC 8 75 506.6 8 3940 4.32
INA2137PA N PDIP 14 25 506 13.97 11230 4.32
INA2137UA D SOIC 14 50 506.6 8 3940 4.32

Pack Materials-Page 3
 IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2024, Texas Instruments Incorporated