0% found this document useful (0 votes)
53 views20 pages

Kit Instructions: NRI Eagle Coin Acceptor Upgrade

Kit Instructions- NCR NRI Eagle Coin Acceptor Upgrade

Uploaded by

atmrmg03
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
53 views20 pages

Kit Instructions: NRI Eagle Coin Acceptor Upgrade

Kit Instructions- NCR NRI Eagle Coin Acceptor Upgrade

Uploaded by

atmrmg03
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 20

Kit Instructions

NRI Eagle Coin Acceptor Upgrade

7350-K913
Issue A
The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. NCR SelfServ™ Checkout is a trademark of NCR Corporation in the United
States and/or other countries. Other product names mentioned in this publication may be trademarks or registered trademarks of
their respective companies and are hereby acknowledged.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks
of HDMI Licensing LLC in the United States and other countries.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is permitted under the
terms and conditions of an agreement you have with NCR, NCR's copyright notice must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become
available. NCR, therefore, reserves the right to change specifications without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances,
photographs are of equipment prototypes. Software screen images are representative, and in some cases, may not match a
customer’s installed software exactly. Therefore, before using this document, consult with your NCR representative or NCR
office for information that is applicable and current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization, and value of this
book. Please use the link below to send your comments.
Email: [email protected]
Copyright © 2021
By NCR Corporation
Global Headquarters
864 Spring St. NW
Atlanta, GA 30308
United States
All Rights Reserved
iii

Revision Record

Issue Date Remarks

A Jun 2021 First issue


iv
NRI Eagle Coin Acceptor Upgrade

This publication provides procedures for upgrading the existing Money Controls SR5i
Coin Acceptor in the NCR SelfServ™ Checkout (7350) with NRI Eagle Coin Acceptor.

Kit Contents

Part Number Description

497-0530735 7350-K913 Kit, NRI Eagle Coin Upgrade


497-0503931 Eagle Coin Acceptor and Cables - Service Part
* 497-0475422 Coin Acceptor Cables - Service Part
497-0501561 Coin Recycler - Eagle Coin Acceptor
* 497–0423108 Instructions Kit (Reference Sheet)

* Items marked with an asterisk are not called out on the image.
2 NRI Eagle Coin Acceptor Upgrade

Installation Procedure
To upgrade the Money Controls SR5i Coin Acceptor in the NCR SelfServ™ Checkout
(7350) to an NRI Eagle Coin Acceptor, follow these steps:
1. Turn off the NCR SelfServ Checkout software and hardware systems.
2. Unlock and open the SelfServ CheckoutCore Door. For more information, refer to
Opening Core Door on the facing page.
3. Remove the existing Coin Acceptor. Depending on the type of Coin Acceptor, refer
to either of the following procedures:
• Removing Money Controls SR5i Coin Acceptor on page 5.
• Removing Money Controls SR5i Coin Acceptor from Metal BCR (BCR 106) on page 8.
4. Install the NRI Eagle Coin Acceptor. Depending on the type of Coin Acceptor, refer
to either of the following procedures:
• Installing NRI Eagle Coin Acceptor on page 10.
• Installing NRI Eagle Coin Acceptor in Metal BCR (BCR 106) on page 11.
5. Close and lock the SelfServ CheckoutCore Door. For more information, refer to
Closing the Core Door on page 14.
6. Run the CADD/ADD Configuration Utility to ensure that the device is updated with
the latest firmware.
Note: Ensure that the upgraded unit is using the CADD_Full_Update_v1.9 +
CADD_1.9_Patch_v3.4 version. If the unit is using a supported software, delete
CADDruntime.dat. The CADD should then detect the NRI Eagle Coin Acceptor.
NRI Eagle Coin Acceptor Upgrade 3

Opening Core Door


To open the Core Door, follow these steps:
1. Use the finger access on the small door to access the door locks, as shown below:

2. In the middle keyhole, insert a key.


3. In Door Latch Handle keyhole, insert a key and then turn it counterclockwise.
4 NRI Eagle Coin Acceptor Upgrade

4. Turn the Door Latch Handle upward and then pull to open the Core Door.
NRI Eagle Coin Acceptor Upgrade 5

Removing Money Controls SR5i Coin Acceptor


To remove the Money Controls SR5i Coin Acceptor, follow these steps:
1. Lift the green latch and rack out the Bulk Coin Recycler from the unit until it is fully
extended.

2. Do the following the remove the main cover:


a. Disconnect the three (3) cable connectors from the Coin Acceptor and Manifold.
6 NRI Eagle Coin Acceptor Upgrade

b. Remove the six (6) captive screws securing the main cover to the Bulk Coin
Recycler chassis.

c. Feed the Coin Acceptor Manifold cable through the hole in the cover.
d. Lift cover off the Coin Recycler.
3. Disconnect the System Power cable from the Coin Recycler control board.
NRI Eagle Coin Acceptor Upgrade 7

4. Do the following:
a. Disconnect the other end of the manifold cable from the Coin Acceptor Chute
Opto PCB, as shown in the image below.
Note: Ensure to remove the cable from the reclosable clip.

5. Push the red tab to the right to release the Money Controls SR5i Coin Acceptor and
then pull it out of the unit.
8 NRI Eagle Coin Acceptor Upgrade

Removing Money Controls SR5i Coin Acceptor from Metal BCR (BCR
106)
To remove the Money Controls SR5i Coin Acceptor, follow these steps:
1. Lift the green latch and rack out the Bulk Coin Recycler from the unit until it is fully
extended.

2. Remove the Main Cover.


NRI Eagle Coin Acceptor Upgrade 9

3. Disconnect the following cables from the Coin Acceptor and the Bulk Coin Recycler,
as shown in the image below.

4. Release the red tab on the right side of the Coin Acceptor and pull acceptor toward
you.

5. Lift the Coin Acceptor out of the Bulk Coin Recycler.


10 NRI Eagle Coin Acceptor Upgrade

Installing NRI Eagle Coin Acceptor


To install the NRI Eagle Coin Acceptor, follow these steps:
1. Insert the NRI Eagle Coin Acceptor into the Coin Recycler unit.
Note: Ensure that the NRI Eagle Coin Acceptor is aligned with the guides on the
BCR and that it is secured in place by the red tab.

2. Connect the System Power cable to the Coin Recycler control board.

3. Connect the cables. For more information, refer to Routing Cables on page 12.
4. Push the Bulk Coin Recycler back to the Core Cabinet.
NRI Eagle Coin Acceptor Upgrade 11

Installing NRI Eagle Coin Acceptor in Metal BCR (BCR 106)


To install the NRI Eagle Coin Acceptor, follow these steps:
1. Insert the NRI Eagle Coin Acceptor into Coin Recycler unit.
Note: Ensure that the NRI Eagle Coin Acceptor is aligned with the guides on the
BCR and that it is secured in place by the red tab.

2. Connect Eagle Coin Acceptor cables, as shown in the image below.

3. Install the main cover back to the Bulk Coin Recycler.


4. Push the Bulk Coin Recycler back to the Core Cabinet.
12 NRI Eagle Coin Acceptor Upgrade

Routing Cables
To route the Eagle Coin Acceptor cables in a Plastic BCR (BCR 206), follow these steps:
1. Connect the manifold cable from to the Coin Acceptor Chute Opto PCB, as shown in
the image below.
Note: Ensure to secure the cable to the reclosable clip.

2. Feed the Coin Acceptor Manifold cable through the hole in the cover.
3. Secure the main cover to the Bulk Coin Recycler chassis using six (6) captive screws.
NRI Eagle Coin Acceptor Upgrade 13

4. Connect the three (3) cable connectors to the Coin Acceptor and Manifold.
14 NRI Eagle Coin Acceptor Upgrade

Closing the Core Door


To close the Core Door, follow these steps:
1. Push the Core Door to the core cabinet and then turn the Door Latch Handle
downward to lock the door.

2. In the middle keyhole, turn the key counterclockwise to completely lock the Core
Door.

3. Remove the keys.


NRI Eagle Coin Acceptor Upgrade 15
16

You might also like