FRONT BACK

EDiTH Diagnostics EDiTH Diagnostics

Connection Quick Reference Card Operation Quick Reference Card
!

2
1

2
Note:
When connected, the green LED on 5
the ISO adapter will indicate a 12 V
power supply and the amber LED will
indicate an active diagnostic link. A 4
constantly lit red LED, may indicate a
communication failure between the 3
heater and the computer.

IMPORTANT
1
After the testing with EDiTH, DO NOT
disconnect the ‘Y’ shaped test adapter
cable until the heater has been switched
off and the cool-down process has been 6
completed.
Hardware Required Activating EDiTH diagnostic tests
1. Double-click the EDiTH shortcut on the desktop to launch the EDiTH program
1 ISO adapter kit (EDiTH basic adapter) : p/n 22 1541 89 0000 2. Click on the ‘Select heater’ icon from the navigation menu displayed
The kit includes; 3. Select the heater type from the groups listed in the far left column
i) ISO adapter (example : Airtronic / Airtronic M / L OR Hydronic B/D 4/5W S/SC etc. )
ii) Black spiral cable with 6-pin connector 4. Click and select the correct heater model number and the correct ECU version
iii) 9-pin to 9-pin serial port connector cable or click and run the ‘Automatic detection’ cycle.
iv) USB 2.0 to 9-pin serial port adapter cable 5. Select the diagnostic test to be activated in the far right column.
v) CD with USB 2.0 to serial port software (example: Error memory, General Data , Functional check or Switch on component)
vi) CD with EDiTH diagnostics software 6. Click on ‘Start test’ button.
Note: EDiTH diagnostic test options
Install the EDiTH software and the software General data : Displays total operating hours and in different heating stages, glow pin
for the USB 2.0 to 9-pin serial port adapter activations, number of start-attempts, number of sucessful ignitions, over-heat
cable, before connecting the ISO adapter counter, failed startup counter, fault codes etc.
to the computer
Functional check : Activates the heater and displays live data on the heater operation
2 Test adapter cable (suited to individual heater type) as it unfolds. This test displays components as they are activated or deactivated, the
Commonly used test adapter cables; operational parameters being measured like temperature, speeds, frequency, voltages,
• p/n 22 1000 31 8600 : ‘Y’ shaped test adapter cable for Airtronic D2/D4/D5 heating modes etc. To switch to a graphic view, select the check boxes against the
• p/n 20 2900 70 5028 : ‘Y’ shaped test adapter cable for Hydronic D5 operational parameters and click on the ‘graph’ tab.
• p/n 20 2900 70 5046 : This universal 6-pin to 8-pin connector adapter cable Switch on component : Enables independent activation and testing of the heater
connects the ISO adaptor to any heater which has components including the blower fan, fuel metering pump, glow pin, coolant pump, etc.
a diagnostic connector built into the main harness Any component defect will be indicated by a fault code. The fuel lines may be primed
For a complete list of test adapter cables, please refer to www.espar.com/help by independently activating the fuel metering pump.
EDiTH Diagnostic Software NOTE: The scope of information displayed in these tests will depend on the type of heater and
the ECU version. The fault codes can be cleared by clicking the ‘Delete’ button.
• EDiTH is an acronym for Eberspaecher Diagnostic Tool Heater
• EDiTH diagnostic software is available for free download from www.espar.com/help
• EDiTH is compatible with most versions of Windows OS, including Windows 7.
• The current version of EDiTH software is S3V11-F (as on June 2011).
• Always uninstall the older version before installing the newer version of the software.