Relion® SAM600

Switchgear control unit SAM600-IO

Version 2.2 IEC
Product guide
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Contents

1. Document revision history.................................................3 8. Ethernet................................................................................ 14

2. Application.............................................................................4 9. Station communication ................................................... 15
3. Available functions...............................................................6 10. Hardware description...................................................... 15
4. Control.................................................................................. 10 11. Connection diagrams...................................................... 18
5. Logic.......................................................................................11 12. Technical data....................................................................19
6. Monitoring............................................................................12 13. Ordering for customized IED.........................................41
7. Basic IED functions............................................................ 14 14. Ordering for Accessories................................................46

Disclaimer

The information in this document is subject to change without notice and should not be construed as a commitment by ABB. ABB assumes no
responsibility for any errors that may appear in this document. Drawings and diagrams are not binding.
© Copyright 2017 ABB. All rights reserved.

Trademarks

ABB and Relion are registered trademarks of the ABB Group. All other brand or product names mentioned in this document may be trademarks or
registered trademarks of their respective holders.
2 ABB
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2 Issued: May 2019
Revision: C

1. Document revision history GUID-7099E1DB-1CD6-4037-A418-92AB57FA9462 v3

Table 1. Document revision history

Document Date Product revision History

revision

A 2017-12 2.2.1 Document not released

B 2017-12 2.2.1 First release for product version 2.2

C 2019-05 2.2.1 PTP enhancements and corrections

ABB 3
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

configuration logic in the IEDs. It means that all binary

inputs and outputs on the IED modules (BOM, BIM, IOM
2. Application GUID-79B8BC84-4AAB-44E7-86CD-FF63098B009D
GUID-E4C46350-2DA9-4F2F-BEB4-2662D7A24E65 v3
v2 and SOM) can be forced to arbitrary values.
The SAM600-IO Switchgear Intelligent Electronic Device
(IED) is used for control and monitoring of primary Central Account Management is an authentication
switchgear in power networks. Typically, one IED is used infrastructure that offers a secure solution for enforcing
for the control of all primary switchgear, such as circuit access control to IED and other systems within a
breakers, disconnectors and earth switches in any type substation. This incorporates management of user
of switchgear arrangement and it is suitable for all accounts, roles and certificates and the distribution of
voltage levels. such, a procedure completely transparent to the user.

IED supports IEC 61850-8-1 Ed1 or IEC 61850-8-1 Ed 2 Flexible Product Naming allows the customer to use an
communication for station bus and process bus. GOOSE IED vendor independent IEC 61850 model of the IED.
messaging is used between IED and control, and This customer model will be used as the IEC 61850 data
protection IEDs for providing status information of the model, but all other aspects of the IED will remain
primary apparatus, as well as subscribing to protection unchanged (e.g., names in the tools). This offers
trip and open/ close operations from the control IEDs. significant flexibility to adapt the IED to the customers'
For monitoring purposes, MMS communication through system and standard solution.
the station bus is also supported.
SAM600-IO LHMI service kit which can be connected to
Built-in redundant communication features such as PRP the IED is available as accessory for maintenance and
and HSR, and up to six communication ports allow to service operations.
embed the IED in a broad range of communication
architectures. Support for IEC/IEEE 61850-9-3 time The IED ships with an empty configuration at delivery.
synchronization enables the integration of the device With PCM600 Tool, required logic for interfacing primary
into state-of-the-art IEC 61850 station and process bus switchgear objects, adjusting function parameters, and
architectures. mapping binary I/O to signals are steps which need to
be performed by the customer.
Control operations of the primary switchgear is
performed from remote (SCADA/Station) via bay control The SAM600-IO basic delivery includes one binary input
IEDs through IEC 61850-8-1 Ed1 or Ed2. Cyber security module and one binary output module, which is
measures are implemented to secure safe autonomous sufficient for interfacing a single circuit breaker. The
operation of the control functions even if simultaneous SAM600-IO is available in two housing variants, ½ 19”,
cyber attacks occur. One IED can be used for interfacing as well as 1/1 19” form factor. Three instances of circuit
the primary switchgear of a single bay, or it can be used breaker and eighteen instances of switchgear objects
(in a 1/1 19” form factor) to interface multiple bays. are included in the basic delivery. For larger applications
covering, an optional circuit breaker package is available
Disturbance recording is available to allow independent which expands the number of controllable switching
post-fault analysis after primary disturbances in case of objects to nine circuit breakers and all operating at a
a failure in the protection system. 3ms cycle time.

Logic is prepared with a graphical tool. The advanced Figure 1 shows a typical usage of SAM600-IO in a double
logic capability allows special applications such as busbar arrangement, covering the I/O signals from all
automatic opening of disconnectors in multi-breaker primary switchgear objects. SAM600-IO is typically
arrangements, closing of breaker rings, load transfer chained in an HSR loop with SAM600 merging units on
logics and so on. The graphical configuration tool an IEC 61850 process bus, receiving and publishing IEC
ensures simple and fast testing and commissioning. 61850 GOOSE information to protection and control
IEDs, such as Relion 670 series.
Forcing of binary inputs and outputs is a convenient way
to test wiring in substations as well as testing

4 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

IEC17000159-1-en.vsdx
IEC17000159 V1 EN-US

Figure 1. SAM600-IO in a 2BB arrangement

ABB 5
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

The following tables list all the

3. Available functions functions available in the IED. Those
GUID-F5776DD1-BD04-4872-BB89-A0412B4B5CC3 v1
functions that are not exposed to the
user or do not need to be configured
are not described in this manual.

6 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Control and monitoring functions GUID-E3777F16-0B76-4157-A3BF-0B6B978863DE v19

IEC 61850 or ANSI Function description Switchgear control unit

function name

SAM600-IO

Control

QCBAY Bay control 2

SXSWI Circuit switch 18

SCSWI Switch controller 30

LOCREM Handling of LR-switch positions 1

SXCBR Circuit breaker 3B

6-H56

POS_EVAL Evaluation of position indication 30

SLGAPC Logic rotating switch for function selection and 15

LHMI presentation

VSGAPC Selector mini switch 30

DPGAPC Generic communication function for Double Point 16

indication

SPC8GAPC Single point generic control function 8 signals 5

Logic

SMPPTRC 94 Tripping logic 12

TMAGAPC Trip matrix logic 12

ALMCALH Logic for group alarm 5

WRNCALH Logic for group warning 5

INDCALH Logic for group indication 5

AND, GATE, INV, Basic configurable logic blocks (see Table 2) 40–160
LLD, OR,
PULSETIMER,
RSMEMORY,
SRMEMORY,
TIMERSET, XOR

FXDSIGN Fixed signal function block 1

B16I Boolean to integer conversion, 16 bit 18

BTIGAPC Boolean to integer conversion with logical node 16

representation, 16 bit

IB16 Integer to Boolean 16 conversion 18

ITBGAPC Integer to Boolean 16 conversion with Logic Node 16

representation

TEIGAPC Elapsed time integrator with limit transgression 54

and overflow supervision

INTCOMP Comparator for integer inputs 30

REALCOMP Comparator for real inputs 30

ABB 7
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Table 2. Total number of instances for basic configurable logic blocks

Basic configurable logic block Total number of instances

AND 160

GATE 40

INV 80

LLD 40

OR 160

PULSETIMER 40

RSMEMORY 60

SRMEMORY 60

TIMERSET 40

XOR 40

IEC 61850 or ANSI Function description Switchgear control unit

function name

SAM600–IO

Monitoring

DRPRDRE, Disturbance report 1

A4RADR,
B1RBDR-B22RBDR

SPGAPC Generic communication function for Single Point 64

indication

SP16GAPC Generic communication function for Single Point 16

indication 16 inputs

MVGAPC Generic communication function for measured 24

values

RANGE_XP Measured value expander block 66

SSIMG 63 Insulation supervision for gas medium 21

SSIML 71 Insulation supervision for liquid medium 3

SSCBR Circuit breaker condition monitoring 27

L4UFCNT Event counter with limit supervision 30

8 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Communication GUID-5F144B53-B9A7-4173-80CF-CD4C84579CB5 v17

IEC 61850 or ANSI Function description Switchgear control

function name unit

SAM600– IO

Station communication

IEC 61850-8-1 IEC 61850 1

GOOSEBINRCV GOOSE binary receive 16

GOOSEDPRCV GOOSE function block to receive a double point value 64

GOOSEINTRCV GOOSE function block to receive an integer value 32

GOOSEMVRCV GOOSE function block to receive a measurand value 60

GOOSESPRCV GOOSE function block to receive a single point value 60

AGSAL Generic security application component 1

LD0LLN0 IEC 61850 LD0 LLN0 1

SYSLLN0 IEC 61850 SYS LLN0 1

LPHD Physical device information 1

PCMACCS IED configuration protocol 1

FSTACCS Field service tool access 1

ACTIVLOG Activity logging 1

ALTRK Service tracking 1

PRP IEC 62439-3 Parallel redundancy protocol 1-P23

HSR IEC 62439-3 High-availability seamless redundancy 1-P24

PTP Precision time protocol 1

SCHLCCH Access point diagnostic for non-redundant Ethernet port 6

RCHLCCH Access point diagnostic for redundant Ethernet ports 3

ABB 9
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Basic IED functions GUID-C8F0E5D2-E305-4184-9627-F6B5864216CA v13

Table 3. Basic IED functions

IEC 61850 or function Description

name

INTERRSIG Self supervision with internal event list

TIMESYNCHGEN Time synchronization module

BININPUT, SNTP Time synchronization

TIMEZONE Time synchronization

SETGRPS Number of setting groups

ACTVGRP Parameter setting groups

TESTMODE Test mode functionality

CHNGLCK Change lock function

SMBI Signal matrix for binary inputs

SMBO Signal matrix for binary outputs

SMMI Signal matrix for mA inputs

ATHSTAT Authority status

ATHCHCK Authority check

AUTHMAN Authority management

FTPACCS FTP access with password

ALTMS Time master supervision

ALTIM Time management

COMSTATUS Protocol diagnostic

the control operations, that is, pass all the commands to

primary apparatuses in the form of disconnectors or
4. Control
earthing switches via binary output boards and to
supervise the switching operation and position.
Switch controller SCSWI
The Switch controller (SCSWI) initializes and supervises
M13486-3 v10
Bay control QCBAY M13447-3 v8
The Bay control (QCBAY) function is used together with
all functions to properly select and operate switching
Local remote and local remote control functions to
primary apparatuses. The Switch controller may handle
handle the selection of the operator place per bay.
and operate on one multi-phase device or up to three
QCBAY also provides blocking functions that can be
one-phase devices.
distributed to different apparatuses within the bay.
Circuit breaker SXCBR
The purpose of Circuit breaker (SXCBR) is to provide the
M13489-3 v6
Local remote LOCREM M17086-3 v11
The signals from an external local/remote switch are
actual status of positions and to perform the control
connected via the function block LOCREM to the QCBAY
operations, that is, pass all the commands to primary
function block.
apparatuses in the form of circuit breakers via binary
output boards and to supervise the switching operation Logic rotating switch for function selection SLGAPC
and position. The logic rotating switch for function selection
SEMOD114908-4 v11

(SLGAPC) (or the selector switch function block) is used

Circuit switch SXSWI M16492-3 v6
to get an enhanced selector switch functionality
The purpose of Circuit switch (SXSWI) function is to
compared to the one provided by a hardware selector
provide the actual status of positions and to perform
10 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

switch. Hardware selector switches are used extensively M15321-3 v13

by utilities, in order to have different functions The trip matrix logic (TMAGAPC) function is used to
operating on pre-set values. Hardware switches are route trip signals and other logical output signals to
however sources for maintenance issues, lower system different output contacts on the IED.
reliability and an extended purchase portfolio. The
The trip matrix logic function has 3 output signals and
selector switch function eliminates all these problems.
these outputs can be connected to physical tripping
Selector mini switch VSGAPC outputs according to the specific application needs for
The Selector mini switch (VSGAPC) function block is a
SEMOD158756-5 v10
settable pulse or steady output.
multipurpose function used for a variety of applications,
Group alarm logic function ALMCALH
as a general purpose switch. GUID-16E60E27-F7A8-416D-8648-8174AAC49BB5 v4
The group alarm logic function (ALMCALH) is used to
VSGAPC can be controlled from binary inputs or via IEC route several alarm signals to a common indication, LED
61850. and/or contact, in the IED.

Generic communication function for Double Point Group warning logic function WRNCALH
GUID-F7D9A012-3AD4-4D86-BE97-DF2A99BE5383 v4

indication DPGAPC The group warning logic function (WRNCALH) is used to

Generic communication function for Double Point
SEMOD55850-5 v7
route several warning signals to a common indication,
indication (DPGAPC) function block is used to send LED and/or contact, in the IED.
double point position indications to other systems,
Group indication logic function INDCALH
equipment or functions in the substation through IEC GUID-D8D1A4EE-A87F-46C6-8529-277FC1ADA9B0 v4
The group indication logic function (INDCALH) is used to
61850-8-1 or other communication protocols. It is
route several indication signals to a common indication,
especially intended to be used in the interlocking
LED and/or contact, in the IED.
station-wide logics.
Basic configurable logic blocks
Single point generic control 8 signals SPC8GAPC SEMOD176462-4 v11 The basic configurable logic blocks do not propagate
M11396-4 v18

The Single point generic control 8 signals (SPC8GAPC)

the time stamp and quality of signals. The list below
function block is a collection of 8 single point
shows a summary of the function blocks and their
commands that can be used for direct commands for
features.
example putting IED in "ChangeLock" state from remote.
In this way, simple commands can be sent directly to the • AND function block. The AND function is used to form
IED outputs, without confirmation. Confirmation general combinatory expressions with boolean
(status) of the result of the commands is supposed to variables. The AND function block has up to four
be achieved by other means, such as binary inputs and inputs and two outputs. One of the outputs is
SPGAPC function blocks. The commands can be pulsed inverted.
or steady with a settable pulse time.
• GATE function block is used for whether or not a
signal should be able to pass from the input to the
output.
5. Logic
• INVERTER function block that inverts the input signal
Tripping logic SMPPTRC M12275-3 v14
to the output.
A function block for protection tripping is always
provided as a basic function for each circuit breaker. It • LLD function block. Loop delay used to delay the
provides a settable pulse prolongation time to ensure a output signal one execution cycle.
trip pulse of sufficient length, as well as all functionality
• OR function block. The OR function is used to form
necessary for correct co-operation with autoreclosing
general combinatory expressions with boolean
functions.
variables. The OR function block has up to six inputs
The trip function block includes a settable latch function and two outputs. One of the outputs is inverted.
for the trip signal and circuit breaker lockout.
• PULSETIMER function block can be used, for example,
The trip function can collect start and directional signals for pulse extensions or limiting of operation of
from different application functions. The aggregated outputs, settable pulse time.
start and directional signals are mapped to the IEC
• RSMEMORY function block is a flip-flop that can reset
61850 logical node data model.
or set an output from two inputs respectively. Each
Trip matrix logic TMAGAPC block has two outputs where one is inverted. The
memory setting controls if, after a power interruption,

ABB 11
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

the flip-flop resets or returns to the state it had SEMOD175781-4 v8

before the power interruption. RESET input has Boolean to integer conversion with logical node
priority. representation, 16 bit (BTIGAPC) is used to transform a
set of 16 boolean (logical) signals into an integer. The
• SRMEMORY function block is a flip-flop that can set or block input will freeze the output at the last value.
reset an output from two inputs respectively. Each
block has two outputs where one is inverted. The Integer to Boolean 16 conversion IB16 SEMOD158373-5 v6

memory setting controls if, after a power interruption, Integer to boolean 16 conversion function (IB16) is used
the flip-flop resets or returns to the state it had to transform an integer into a set of 16 boolean (logical)
before the power interruption. The SET input has signals.
priority.
Integer to Boolean 16 conversion with logic node
• TIMERSET function has pick-up and drop-out delayed representation ITBGAPC SEMOD158421-5 v9

outputs related to the input signal. The timer has a Integer to boolean conversion with logic node
settable time delay. representation function (ITBGAPC) is used to transform
an integer which is transmitted over IEC 61850 and
• XOR is used to generate combinatory expressions received by the function to 16 boolean (logic) output
with boolean variables. XOR has two inputs and two signals.
outputs. One of the outputs is inverted. The output
signal OUT is 1 if the input signals are different and 0 Comparator for integer inputs INTCOMP
GUID-A93564FA-0017-4939-A9C1-095DA0FD9832 v1

if they are the same. The function gives the possibility to monitor the level of
integer values in the system relative to each other or to
a fixed value. It is a basic arithmetic function that can be
Fixed signal function block FXDSIGN M15322-3 v15
used for monitoring, supervision, interlocking and other
The Fixed signals function (FXDSIGN) has nine pre-set logics.
(fixed) signals that can be used in the configuration of
an IED, either for forcing the unused inputs in other Comparator for real inputs REALCOMP GUID-E17A88D7-D095-4F36-9CD5-64EBFD2A1DEA v1
function blocks to a certain level/value, or for creating The function gives the possibility to monitor the level of
certain logic. Boolean, integer, floating point, string real value signals in the system relative to each other or
types of signals are available. to a fixed value. It is a basic arithmetic function that can
be used for monitoring, supervision, interlocking and
One FXDSIGN function block is included in all IEDs. other logics.

Elapsed time integrator with limit transgression and

overflow supervision TEIGAPC GUID-2D64874A-F266-4251-8EED-E813F40513D7 v3
The Elapsed time integrator function (TEIGAPC) is a
6. Monitoring
function that accumulates the elapsed time when a
given binary signal has been high. Supervision of mA input signals M16054-3 v2
The main purpose of the function is to measure and
The main features of TEIGAPC
process signals from different measuring transducers.
• Applicable to long time integration (≤999 999.9 Many devices used in process control represent various
seconds). parameters such as frequency, temperature and DC
• Supervision of limit transgression conditions and battery voltage as low current values, usually in the
overflow. range 4-20 mA or 0-20 mA.
• Possibility to define a warning or alarm with the
Alarm limits can be set and used as triggers, e.g. to
resolution of 10 milliseconds.
generate trip or alarm signals.
• Retaining of the integration value.
• Possibilities for blocking and reset. The function requires that the IED is equipped with the
• Reporting of the integrated time. mA input module.

Disturbance report DRPRDRE

Boolean to integer conversion, 16 bit B16I M12153-3 v14
SEMOD175725-4 v5 Complete and reliable information about disturbances in
Boolean to integer conversion, 16 bit (B16I) is used to
the primary and/or in the secondary system together
transform a set of 16 boolean (logical) signals into an
with continuous event-logging is accomplished by the
integer.
disturbance report functionality.
Boolean to integer conversion with logical node
Disturbance report (DRPRDRE), always included in the
representation, 16 bit BTIGAPC
IED, acquires sampled data of all selected binary signals

12 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

connected to the function block with a maximum of 352

binary signals. Disturbance recorder DRPRDRE M12156-3 v12
The Disturbance recorder function supplies fast,
The Disturbance report functionality is a common name complete and reliable information about disturbances in
for several functions: the power system. It facilitates understanding system
behavior and related primary and secondary equipment
• Event list during and after a disturbance. Recorded information is
• Indications used for different purposes in the short perspective (for
• Event recorder example corrective actions) and long perspective (for
• Disturbance recorder example functional analysis).
• Settings information
The Disturbance recorder acquires sampled data from
The Disturbance report function is characterized by selected analog and binary signals connected to the
great flexibility regarding configuration, starting Disturbance recorder function (10 analog channels and
conditions, recording times, and large storage capacity. 352 binary signals). The binary signals available are the
same as for the event recorder function.
A disturbance is defined as an activation of an input to
the AnRADR or BnRBDR function blocks, which are set to The function is characterized by great flexibility and is
trigger the disturbance recorder. All connected signals not dependent on the operation of other functions. Up
from start of pre-fault time to the end of post-fault time to ten seconds of data before the trigger instant can be
will be included in the recording. Disturbance record will saved in the disturbance file.
have visible settings from all function instances that are
configured in the application configuration tool. The disturbance recorder information for up to 100
disturbances are saved in the IED and that can be
Every disturbance report recording is saved in the IED in viewed in PCM600 disturbance tool.
the standard Comtrade format as a reader file HDR, a
configuration file CFG, and a data file DAT. The same Generic communication function for Single Point
applies to all events, which are continuously saved in a indication SPGAPC SEMOD55713-5 v8
ring-buffer. The disturbance report files can be Generic communication function for Single Point
uploaded to PCM600 for further analysis using the indication (SPGAPC) is used to send one single logical
disturbance handling tool. signal to other systems or equipment in the substation.

Event list DRPRDRE Generic communication function for measured

M12412-6 v8
Continuous event-logging is useful for monitoring the values MVGAPC SEMOD55872-5 v10
system from an overview perspective and is a Generic communication function for measured values
complement to specific disturbance recorder functions. (MVGAPC) function is used to send the instantaneous
value of an analog signal to other systems or equipment
The event list logs all binary input signals connected to in the substation. It can also be used inside the same
the Disturbance recorder function. The list may contain IED, to attach a RANGE aspect to an analog value and to
up to 1000 time-tagged events stored in a ring-buffer. permit measurement supervision on that value.

Event recorder DRPRDRE M12033-3 v8 Measured value expander block RANGE_XP

Quick, complete and reliable information about
SEMOD52450-4 v8
The IEC 61850 generic communication I/O function
disturbances in the primary and/or in the secondary MVGAPC is provided with measurement supervision
system is vital, for example, time-tagged events logged functionality. All measured values can be supervised
during disturbances. This information is used for with four settable limits: low-low limit, low limit, high
different purposes in the short term (for example limit and high-high limit. The measure value expander
corrective actions) and in the long term (for example block (RANGE_XP) has been introduced to enable
functional analysis). translating the integer output signal from the
measuring functions to 5 binary signals: below low-low
The event recorder logs all selected binary input signals
limit, below low limit, normal, above high limit or above
connected to the Disturbance recorder function. Each
high-high limit. The output signals can be used as
recording can contain up to 150 time-tagged events.
conditions in the configurable logic or for alarming
The event recorder information is available for the purpose.
disturbances locally in the IED.
Insulation supervision for liquid medium SSIML
GUID-3B1A665F-60A5-4343-85F4-AD9C066CBE8D v7

The event recording information is an integrated part of Insulation supervision for liquid medium (SSIML) is used
the disturbance record (Comtrade file). for monitoring the oil insulated device condition. For
example, transformers, shunt reactors, and so on. Binary
ABB 13
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

information based on the oil level in the oil insulated GUID-6E5D2696-A8EE-43E7-A94B-69C3D0612127 v2

devices are used as input signals to the function. In An access point is an Ethernet communication interface
addition, the function generates alarms based on the for single or redundant station communication. Each
received information. access point is allocated with one physical Ethernet
port, two physical Ethernet ports are allocated if
Circuit breaker condition monitoring SSCBR
GUID-E1FD74C3-B9B6-4E11-AA1B-7E7F822FB4DD v13
redundant communication is activated for the access
The circuit breaker condition monitoring function point.
(SSCBR) is used to monitor different parameters of the
breaker condition. The breaker requires maintenance
Device 1 Device 1
when the number of operations reaches a predefined
value. For a proper functioning of the circuit breaker, it AP1 AP2 AP3 AP1 AP2 AP3
is essential to monitor the circuit breaker operation, SFP_301 SFP_302 SFP_303 SFP_301 SFP_302 SFP_303

spring charge indication or breaker wear, travel time, IEC16000092-1-en.vsdx

number of operation cycles. IEC16000092 V1 EN-US

Figure 2. Access points, non redundant (left) and redundant

communication (right)
Event counter with limit supervison L4UFCNT
GUID-13157EAB-1686-4D2E-85DF-EC89768F3572 v6
The Limit counter (L4UFCNT) provides a settable
counter with four independent limits where the number
Access points diagnostics
of positive and/or negative flanks on the input signal GUID-20F64A6D-AA8C-47D7-AA7D-4810996B2FF2 v2
The access point diagnostics function blocks (RCHLCCH
are counted against the setting values for limits. The
and SCHLCCH) supervise communication. SCHLCCH is
output for each limit is activated when the counted
used for communication over the rear Ethernet ports
value reaches that limit.
and RCHLCCH is used for redundant communications
Overflow indication is included for each up-counter. over the rear Ethernet ports. Both access point function
blocks include output signal for denial of service.

Redundant communication GUID-A90FDBA7-D4D7-4CBD-9F05-13DCC9971779 v7

7. Basic IED functions IEC 62439-3 redundant communication PRP

Redundant communication according to IEC 62439-3
Time synchronization M11344-3 v11 PRP-0, IEC 62439-3 PRP-1 parallel redundancy protocol
The time synchronization function is used to select a
(PRP) is available as an option when ordering IEDs. PRP
common source of absolute time for the synchronization
according to IEC 62439-3 uses two optical Ethernet
of the IED when it is a part of a protection system. This
ports.
makes it possible to compare events and disturbance
data between all IEDs within a station automation IEC 62439-3 High-availability seamless redundancy HSR
system and in between sub-stations. Redundant station bus communication according to IEC
M11345-3 v11 62439-3 Edition 2 High-availability seamless redundancy
Precision time protocol PTP (HSR) is available as an option when ordering IEDs.
PTP according to IEEE 1588-2008 and specifically its Redundant station bus communication according to IEC
profile IEC/IEEE 61850-9-3 for power utility automation 62439-3 uses two optical Ethernet ports.
is a synchronization method that can be used to
The HSR ring supports the connection of up to 30 relays.
maintain a common time within a station. This time can
If more than 30 relays are to be connected, it is
be synchronized to the global time using, for instance, a
recommended to split the network into several rings to
GPS receiver. If PTP is enabled on the IEDs and the
guarantee the performance for real-time applications.
switches that connect the station are compatible with
IEEE 1588, the station will become synchronized to one Routes
common time with an accuracy of under 1us. Using an A route is a specified path for data to travel between the
GUID-95F9C7BA-92F8-489F-AD0A-047410B5E66F v1

IED as a boundary clock between several networks will source device in a subnetwork to the destination device
keep 1us accuracy on three levels or when using an HSR, in a different subnetwork. A route consists of a
15 IEDs can be connected in a ring without losing a destination address and the address of the gateway to
single microsecond in accuracy. be used when sending data to the destination device,
see Figure 3.

8. Ethernet

Access points
14 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

the battery system. An internal fail alarm output is

available.

Alternative connectors of Ring lug or Compression type

can be ordered.
Default gateway

Binary input module BIM

M1769-3 v4
The binary input module has 16 optically isolated inputs
Gateway
and is available in two versions, one standard and one
with enhanced pulse counting capabilities on the inputs
Source Destination
IEC16000095-1-en.vsdx
to be used with the pulse counter function. The binary
IEC16000095 V1 EN-US
inputs are freely programmable and can be used for the
Figure 3. Route from source to destination through gateway
input of logical signals to any of the functions. They can
also be included in the disturbance recording and event-
recording functions. This enables extensive monitoring
and evaluation of operation of the IED and for all
associated electrical circuits.
9. Station communication
Binary output module BOM
M6938-3 v4

Communication protocols The binary output module has 24 independent output

relays and is used for trip output or any signaling
M14815-3 v14
Each IED is provided with several communication
interfaces enabling it to connect to one or many purpose.
substation level systems or equipment, either on the
Static binary output module SOM
Substation Automation (SA) bus or Substation SEMOD174196-4 v4
The static binary output module has six fast static
Monitoring (SM) bus.
outputs and six change over output relays for use in
Available communication protocols are: applications with high speed requirements.

• IEC 61850-8-1 communication protocol Binary input/output module IOM

M6939-3 v6
The binary input/output module is used when only a few
input and output channels are needed. The ten standard
IEC 61850-8-1 communication protocol M14787-3 v16 output channels are used for trip output or any signaling
IEC 61850 Ed.1 or Ed.2 can be chosen by a setting in
purpose. The two high speed signal output channels are
PCM600. The IED is equipped with up to six (order
used for applications where short operating time is
dependent) optical Ethernet rear ports for IEC 61850-8-1
essential. Eight optically isolated binary inputs cater for
station bus communication. IEC 61850-8-1 protocol
required binary input information.
allows intelligent electrical devices (IEDs) from different
vendors to exchange information and simplifies system mA input module MIM
M15020-3 v4
engineering. IED-to-IED communication using GOOSE The milli-ampere input module is used to interface
and client-server communication over MMS are transducer signals in the –20 to +20 mA range from for
supported. Disturbance recording file (COMTRADE) example OLTC position, temperature or pressure
uploading can be done over MMS or FTP. transducers. The module has six independent,
galvanically separated channels.

Optical Ethernet module

M16073-3 v9

10. Hardware description The optical Ethernet module (OEM) provides two
additional optical Ethernet ports. The port connectors
Hardware modules IP14529-1 v1
are:
Numeric processing module NUM
M12643-3 v4
The numeric processing module (NUM) is a CPU module
that handles all protection functions and logic.

NUM provides up to 4 optical (type LC) or galvanic (type

RJ45) Ethernet ports (four basic).

Power supply module PSM

M11595-3 v6
The power supply module is used to provide the correct
internal voltages and full isolation between the IED and

ABB 15
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

• SFP Optical LC
• Galvanic RJ45

Layout and dimensions IP14539-1 v1

Dimensions
IP14826-1
M15243-4 v1
v7

A
D
IEC17000156-1-en.vsdx

IEC17000156 V1 EN-US

Figure 6. A 1/2 x 19” size IED side-by-side with RHGS6.

M2152-3 v8

B
C

E
IEC17000157-1-en.vsdx

IEC17000157 V1 EN-US

Figure 4. Case with rear cover

A
D

B C

IEC17000128-1-en.vsdx

IEC17000128 V1 EN-US

Figure 7. Case without protective cover

Figure 8. Case without protective cover with 19” rack mounting

kit

IEC08000165‐3‐en.vsdx
M15243-12 v10

IEC08000165 V3 EN-US

Figure 5. Case with rear cover and 19” rack mounting kit

16 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Case size A B C D E F G H I
(mm)/
(inches)

6U, 1/2 x 19” 265.9/ 223.7/ 247.5/ 255.0/ 205.8/ 190.5/ 466.5/ 232.5/ 482.6/
10.47 8.81 9.74 10.04 8.10 7.50 18.36 9.15 19

6U, 1/1 x 19” 265.9/ 448.0/ 247.5/ 255.0/ 430.1/ 190.5/ 466.5/ 232.5/ 482.6/
10.47 17.65 9.74 10.04 16.86 7.50 18.36 9.15 19

The G and H dimensions are defined by the 19” rack mounting kit.

Mounting alternatives See ordering for details about available mounting

M16079-3 v14
• 19” rack mounting kit alternatives.
• Wall mounting kit

ABB 17
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Connection diagram, SAM600-IO 2.2 IEC symbols,

1MRK002851–AA
11. Connection diagrams GUID-CF4EFFA5-3081-4FC7-9A14-ED127C3C0FDE v7
The connection diagrams are delivered in the IED Connection diagram, SAM600-IO 2.2 ANSI symbols,
Connectivity package as part of the product delivery. 1MRK002852–AA

The latest versions of the connection diagrams can be

downloaded from
http://www.abb.com/protection-control.

18 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

12. Technical data

General M10993-1 v3 IP11376-1 v2

Definitions

Reference value The specified value of an influencing factor to which are referred the characteristics of the equipment

Nominal range The range of values of an influencing quantity (factor) within which, under specified conditions, the equipment meets
the specified requirements

Operative range The range of values of a given energizing quantity for which the equipment, under specified conditions, is able to
perform its intended functions according to the specified requirements

GUID-1E949E38-E04D-4374-A086-912C25E9F93C v2
Presumptions for Technical Data For operate and reset time testing, the default setting
values of the function are used if not explicitly stated
otherwise.

ABB 19
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Energizing quantities, rated values and limits

Analog inputs
M16988-1
M6389-1v11
v5 IP15842-1 v1

Table 4. MIM - mA input module

Quantity: Rated value: Nominal range:

Input resistance Rin = 194 Ohm -

Input range ±5, ±10, ±20 mA -

0-5, 0-10, 0-20, 4-20 mA

Power consumption -
each mA board £2W
each mA input £ 0.1 W

Auxiliary DC voltage
M12286-1 v9 IP15843-1 v3

Table 5. PSM - Power supply module

Quantity Rated value Nominal range

Auxiliary DC voltage, EL (input) EL = (24-60) V EL ±20%

EL = (90-250) V EL ±20%

Power consumption 50 W typically -

Auxiliary DC power in-rush < 10 A during 0.1 s -

Supply interruption bridging time < 50 ms -

Binary inputs and outputs

M12576-1 v12 IP15844-1 v1

Table 6. BIM - Binary input module

Quantity Rated value Nominal range

Binary inputs 16 -

DC voltage, RL 24/30 V RL ±20%

48/60 V RL ±20%
110/125 V RL ±20%
220/250 V RL ±20%

Power consumption
24/30 V, 50 mA max. 0.05 W/input -
48/60 V, 50 mA max. 0.1 W/input
110/125 V, 50 mA max. 0.2 W/input
220/250 V, 50 mA max. 0.4 W/input
220/250 V, 110 mA max. 0.5 W/input

Counter input frequency 10 pulses/s max -

Oscillating signal discriminator Blocking settable 1–40 Hz

Release settable 1–30 Hz

*Debounce filter Settable 1–20 ms

Binary input operate time 3 ms -

(Debounce filter set to 0 ms)

* Note: For compliance with surge immunity a debounce filter time setting of 5 ms is required.

20 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Maximum 176 binary input channels The stated operate time for functions
may be activated simultaneously with include the operating time for the
influencing factors within nominal binary inputs and outputs.
range.
M50609-2 v9

Table 7. BIM - Binary input module with enhanced pulse counting capabilities

Quantity Rated value Nominal range

Binary inputs 16 -

DC voltage, RL 24/30 V RL ±20%

48/60 V RL ±20%
110/125 V RL ±20%
220/250 V RL ±20%

Power consumption
24/30 V max. 0.05 W/input -
48/60 V max. 0.1 W/input
110/125 V max. 0.2 W/input
220/250 V max. 0.4 W/input

Counter input frequency 10 pulses/s max -

Balanced counter input frequency 40 pulses/s max -

Oscillating signal discriminator Blocking settable 1–40 Hz

Release settable 1–30 Hz

*Debounce filter Settable 1-20 ms

Binary input operate time 3 ms -

(Debounce filter set to 0 ms)

* Note: For compliance with surge immunity a debounce filter time setting of 5 ms is required.

ABB 21
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Maximum 176 binary input channels The stated operate time for functions
may be activated simultaneously with include the operating time for the
influencing factors within nominal binary inputs and outputs.
range.
M12573-1 v11

Table 8. IOM - Binary input/output module

Quantity Rated value Nominal range

Binary inputs 8 -

DC voltage, RL 24/30 V RL ±20%

48/60 V RL ±20%
110/125 V RL ±20%
220/250 V RL ±20%

Power consumption -
24/30 V, 50 mA max. 0.05 W/input
48/60 V, 50 mA max. 0.1 W/input
110/125 V, 50 mA max. 0.2 W/input
220/250 V, 50 mA max. 0.4 W/input
220/250 V, 110 mA max. 0.5 W/input

Counter input frequency 10 pulses/s max

Oscillating signal discriminator Blocking settable 1-40 Hz

Release settable 1-30 Hz

*Debounce filter Settable 1-20 ms

Binary input operate time 3 ms -

(Debounce filter set to 0 ms)

* Note: For compliance with surge immunity a debounce filter time setting of 5 ms is required.

22 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Maximum 176 binary input channels The stated operate time for functions
may be activated simultaneously with include the operating time for the
influencing factors within nominal binary inputs and outputs.
range.
M12318-1 v10

Table 9. IOM - Binary input/output module contact data (reference standard: IEC 61810-2)

Function or quantity Trip and signal relays Fast signal relays (parallel
reed relay)

Binary outputs 10 2

Max system voltage 250 V AC, DC 250 V DC

Min load voltage 24VDC —

Test voltage across open contact, 1 min 1000 V rms 800 V DC

Current carrying capacity

Per relay, continuous 8A 8A
Per relay, 1 s 10 A 10 A
Per process connector pin, continuous 12 A 12 A

Making capacity at inductive load with L/R > 10 ms

0.2 s
1.0 s 30 A 0.4 A
10 A 0.4 A

Making capacity at resistive load

220–250 V/0.4 A
0.2 s 30 A 110–125 V/0.4 A
1.0 s 10 A 48–60 V/0.2 A
24–30 V/0.1 A

Breaking capacity for AC, cos φ > 0.4 250 V/8.0 A 250 V/8.0 A

Breaking capacity for DC with L/R < 40 ms 48 V/1 A 48 V/1 A

110 V/0.4 A 110 V/0.4 A
125 V/0.35 A 125 V/0.35 A
220 V/0.2 A 220 V/0.2 A
250 V/0.15 A 250 V/0.15 A

Maximum capacitive load - 10 nF

Max operations with load 1000

Max operations with no load 10000

Operating time < 6 ms <= 1 ms

ABB 23
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Maximum 72 outputs may be activated The stated operate time for functions
simultaneously with influencing factors include the operating time for the
within nominal range. After 6 ms an binary inputs and outputs.
additional 24 outputs may be
activated. The activation time for the M12584-1 v10

96 outputs must not exceed 200 ms. 48

outputs can be activated during 1 s.
Continued activation is possible with
respect to current consumption but
after 5 minutes the temperature rise
will adversely affect the hardware life.
Maximum two relays per
BOM/IOM/SOM should be activated
continuously due to power dissipation.

Table 10. IOM with MOV and IOM 220/250 V, 110mA - contact data (reference standard: IEC 61810-2)

Function or quantity Trip and Signal relays Fast signal relays (parallel reed relay)

Binary outputs IOM: 10 IOM: 2

Max system voltage 250 V AC, DC 250 V DC

Min load voltage 24VDC -

Test voltage across open 250 V rms 250 V rms

contact, 1 min

Current carrying capacity

Per relay, continuous 8A 8A
Per relay, 1 s 10 A 10 A
Per process connector pin, 12 A 12 A
continuous

Making capacity at inductive

loadwith L/R > 10 ms
0.2 s 30 A 0.4 A
1.0 s 10 A 0.4 A

Making capacity at resistive

load 220–250 V/0.4 A
30 A 110–125 V/0.4 A
0.2 s 10 A 48–60 V/0.2 A
1.0 s 24–30 V/0.1 A

Breaking capacity for AC, cos j 250 V/8.0 A 250 V/8.0 A

> 0.4

Breaking capacity for DC with 48 V/1 A 48 V/1 A

L/R < 40 ms 110 V/0.4 A 110 V/0.4 A
220 V/0.2 A 220 V/0.2 A
250 V/0.15 A 250 V/0.15 A

Maximum capacitive load - 10 nF

Max operations with load 1000 -

Max operations with no load 10000 -

Operating time < 6 ms <= 1 ms

24 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Maximum 72 outputs may be activated The stated operate time for functions
simultaneously with influencing factors include the operating time for the
within nominal range. After 6 ms an binary inputs and outputs.
additional 24 outputs may be
activated. The activation time for the SEMOD175395-2 v9

96 outputs must not exceed 200 ms. 48

outputs can be activated during 1 s.
Continued activation is possible with
respect to current consumption but
after 5 minutes the temperature rise
will adversely affect the hardware life.
Maximum two relays per
BOM/IOM/SOM should be activated
continuously due to power dissipation.

Table 11. SOM - Static Output Module (reference standard: IEC 61810-2): Static binary outputs

Function of quantity Static binary output trip

Rated voltage 48-60 VDC 110-250 VDC

Number of outputs 6 6

Impedance open state ~300 kΩ ~810 kΩ

Test voltage across open contact, 1 min No galvanic separation No galvanic separation

Current carrying capacity:

Continuous 5A 5A

1.0 s 10 A 10 A

Making capacity at capacitive load with the

maximum capacitance of 0.2 μF :

0.2 s 30 A 30 A

1.0 s 10 A 10 A

Breaking capacity for DC with L/R ≤ 40 ms 48 V/1 A 110 V/0.4 A

60 V/0.75 A 125 V/0.35 A

220 V/0.2 A

250 V/0.15 A

Operating time < 1 ms < 1 ms

ABB 25
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Table 12. SOM - Static Output module data (reference standard: IEC 61810-2): Electromechanical relay outputs

Function of quantity Trip and signal relays

Max system voltage 250 V AC/DC

Min load voltage 24VDC

Number of outputs 6

Test voltage across open contact, 1 min 1000 V rms

Current carrying capacity:

Continuous 8A

1.0 s 10 A

Max operations with load 1000

Max operations with no load 10000

Making capacity at capacitive load with the maximum capacitance

of 0.2 μF:

0.2 s 30 A

1.0 s 10 A

Breaking capacity for DC with L/R ≤ 40 ms 48 V/1 A

110 V/0.4 A

125 V/0.35 A

220 V/0.2 A

250 V/0.15 A

Operating time < 6 ms

26 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

M12441-1 v10

The stated operate time for functions

include the operating time for the
binary inputs and outputs.

Table 13. BOM - Binary output module contact data (reference standard: IEC 61810-2)

Function or quantity Trip and Signal relays

Binary outputs 24

Max system voltage 250 V AC, DC

Min load voltage 24VDC

Test voltage across open contact, 1 min 1000 V rms

Current carrying capacity

Per relay, continuous 8A
Per relay, 1 s 10 A
Per process connector pin, continuous 12 A

Max operations with load 1000

Max operations with no load 10000

Making capacity at inductive load with L/R > 10 ms

0.2 s 30 A
1.0 s 10 A

Breaking capacity for AC, cos j > 0.4 250 V/8.0 A

Breaking capacity for DC with L/R < 40 ms 48 V/1 A

110 V/0.4 A
125 V/0.35 A
220 V/0.2 A
250 V/0.15 A

Operating time < 6 ms

The stated operate time for functions

include the operating time for the
binary inputs and outputs.

Influencing factors
M16705-1 v16 IP15846-1 v1

Table 14. Temperature and humidity influence

Parameter Reference value Nominal range Influence

Ambient temperature, operate +20±5°C -25°C to +55°C 0.02%/°C

value

Relative humidity 45-75% 10-90% -

Operative range 0-95%

Storage temperature - -40°C to +70°C -

ABB 27
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Table 15. Auxiliary DC supply voltage influence on functionality during operation

Dependence on Reference value Within nominal Influence

range

Ripple, in DC auxiliary voltage max. 2% 15% of EL 0.01%/%

Operative range Full wave
rectified

Auxiliary voltage dependence, ±20% of EL 0.01%/%

operate value

Interrupted auxiliary DC voltage 24-60 V DC ± 20%

100-250 V DC ±20%
Interruption
interval
0–50 ms No restart

0–∞ s Correct behaviour at power down

Restart time < 300 s

Type tests according to standards M16706-1 v14 IP15778-1 v1

Table 16. Electromagnetic compatibility

Test Type test values Reference standards

1 MHz burst disturbance 2.5 kV IEC 60255-26

100 kHz slow damped oscillatory wave immunity test 2.5 kV IEC 61000-4-18, Level 3

Ring wave immunity test, 100 kHz 2-4 kV IEC 61000-4-12, Level 4

Electrostatic discharge 15 kV air discharge IEC 60255-26

Direct application 8 kV contact discharge
Indirect application 8 kV contact discharge IEC 61000-4-2, Level 4

Electrostatic discharge 15 kV air discharge IEEE/ANSI C37.90.3

Direct application 8 kV contact discharge
Indirect application 8 kV contact discharge

Fast transient disturbance 4 kV IEC 60255-26, Zone A

2 kV, SFP galvanic RJ45
2 kV, MIM mA-inputs IEC 60255-26, Zone B

Surge immunity test 2-4 kV, 1.2/50ms high energy IEC 60255-26, Zone A
1-2 kV, BOM and IRF outputs IEC 60255-26, Zone B

Power frequency immunity test 150-300 V, 50 Hz IEC 60255-26, Zone A

Conducted common mode immunity test 30-3 V, 15-150 Hz IEC 61000-4-16, Level 4

Power frequency magnetic field test 1000 A/m, 3 s IEC 61000-4-8, Level 5
100 A/m, cont.

Pulse magnetic field immunity test 1000 A/m IEC 61000–4–9, Level 5

Damped oscillatory magnetic field test 100 A/m IEC 61000-4-10, Level 5

Radiated electromagnetic field disturbance 20 V/m IEC 60255-26

80-1000 MHz IEEE/ANSI C37.90.2
1.4-2.7 GHz EN 50121-5
10 V/m, 2.7-6.0 GHz

Radiated emission 30-6000 MHz IEC 60255-26

30-8500 MHz IEEE/ANSI C63.4, FCC

Conducted emission 0.15-30 MHz IEC 60255-26

28 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Table 17. Insulation

Test Type test values Reference standard

Dielectric test 2.0 kV AC, 1 min. IEC 60255-27

1.0 kV AC, 1 min.: ANSI C37.90
-SFP galvanic RJ45 IEEE 802.3-2015,
- X.21-LDCM Environment A

Impulse voltage test 5 kV, 1.2/50ms, 0.5 J

1 kV, 1.2/50 ms 0.5 J:
-SFP galvanic RJ45
- X.21-LDCM

Insulation resistance > 100 MW at 500 VDC

Table 18. Environmental tests

Test Type test value Reference standard

Cold operation test Test Ad for 16 h at -40°C IEC 60068-2-1

Cold storage test Test Ab for 16 h at -40°C IEC 60068-2-1

Dry heat operation test Test Bd for 16 h at +70°C IEC 60068-2-2

Dry heat storage test Test Bb for 16 h at +85°C IEC 60068-2-2

Change of temperature test Test Nb for 5 cycles at -25°C to +70°C IEC 60068-2-14

Damp heat test, steady state Test Ca for 10 days at +40°C and humidity 93% IEC 60068-2-78

Damp heat test, cyclic Test Db for 6 cycles at +25 to +55°C and humidity 93 to 95% (1 cycle IEC 60068-2-30
= 24 hours)

Table 19. CE compliance

Test According to

Electromagnetic compatibility (EMC) EN 60255–26

Low voltage (LVD) EN 60255–27

Table 20. Mechanical tests

Test Type test values Reference standards

Vibration response test Class II: Rack mount IEC 60255-21-1

Class I: Flush and wall mount

Vibration endurance test Class I: Rack, flush and wall mount IEC 60255-21-1

Shock response test Class I: Rack, flush and wall mount IEC 60255-21-2

Shock withstand test Class I: Rack, flush and wall mount IEC 60255-21-2

Bump test Class I: Rack, flush and wall mount IEC 60255-21-2

Seismic test Class II: Rack mount IEC 60255-21-3

Class I: Flush and wall mount

ABB 29
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Logic M12380-1 v14

Table 21. Tripping logic common 3-phase output SMPPTRC

Function Range or value Accuracy

Trip action 3-ph, 1/3-ph, 1/2/3-ph -

Minimum trip pulse length (0.000-60.000) s ±0.2% or ±15 ms whichever is greater

3-pole trip delay (0.020-0.500) s ±0.2% or ±15 ms whichever is greater

Evolving fault delay (0.000-60.000) s ±0.2% or ±15 ms whichever is greater

Table 22. Number of SMPPTRC instances

Function Quantity with cycle time

3 ms 8 ms

SMPPTRC 12 -
GUID-3AB1EE95-51BF-4CC4-99BD-F4ECDAACB75A v3

Table 23. Number of TMAGAPC instances

Function Quantity with cycle time

3 ms 8 ms

TMAGAPC 12 -
GUID-A05AF26F-DC98-4E62-B96B-E75D19F20767 v2

Table 24. Number of ALMCALH instances

Function Quantity with cycle time

3 ms 8 ms

ALMCALH - 5
GUID-70B7357D-F467-4CF5-9F73-641A82D334F5 v2

Table 25. Number of WRNCALH instances

Function Quantity with cycle time

3 ms 8 ms

WRNCALH - 5
GUID-EAA43288-01A5-49CF-BF5B-9ABF6DC27D85 v2

Table 26. Number of INDCALH instances

Function Quantity with cycle time

3 ms 8 ms

INDCALH - 5
GUID-D1179280-1D99-4A66-91AC-B7343DBA9F23 v3

Table 27. Number of AND instances

Logic block Quantity with cycle time

3 ms 8 ms

AND 80 80

30 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

GUID-45DF373F-DC39-4E1B-B45B-6B454E8E0E50 v3

Table 28. Number of GATE instances

Logic block Quantity with cycle time

3 ms 8 ms

GATE 20 20
GUID-0EC4192A-EF03-47C0-AEC1-09B68B411A98 v3

Table 29. Number of INV instances

Logic block Quantity with cycle time

3 ms 8 ms

INV 40 40
GUID-B2E6F510-8766-4381-9618-CE02ED71FFB6 v2

Table 30. Number of LLD instances

Logic block Quantity with cycle time

3 ms 8 ms

LLD 20 20
GUID-35A795D7-A6BD-4669-A023-43C497DBFB01 v4

Table 31. Number of OR instances

Logic block Quantity with cycle time

3 ms 8 ms

OR 80 80
GUID-E05E5FB1-23E7-4816-84F2-1FBFFDFF2B43 v2

Table 32. Number of PULSETIMER instances

Logic block Quantity with cycle time Range or Value Accuracy

3 ms 8 ms

PULSETIMER 20 20 (0.000–90000.000) s ±0.5% ±10 ms

GUID-BE6FD540-E96E-4F15-B2A2-12FFAE6C51DB v2

Table 33. Number of RSMEMORY instances

Logic block Quantity with cycle time

3 ms 8 ms

RSMEMORY 20 40
GUID-7A0F4327-CA83-4FB0-AB28-7C5F17AE6354 v2

Table 34. Number of SRMEMORY instances

Logic block Quantity with cycle time

3 ms 8 ms

SRMEMORY 20 40
GUID-C6C98FE0-F559-45EE-B853-464516775417 v3

Table 35. Number of TIMERSET instances

Logic block Quantity with cycle time Range or Value Accuracy

3 ms 8 ms

TIMERSET 20 20 (0.000–90000.000) s ±0.5% ±10 ms

ABB 31
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

GUID-0B07F78C-10BD-4070-AFF0-6EE36454AA03 v2

Table 36. Number of XOR instances

Logic block Quantity with cycle time

3 ms 8 ms

XOR 20 20
GUID-65A2876A-F779-41C4-ACD7-7662D1E7F1F2 v3

Table 37. Number of B16I instances

Function Quantity with cycle time

3 ms 8 ms

B16I 9 9
GUID-3820F464-D296-4CAD-8491-F3F997359D79 v2

Table 38. Number of BTIGAPC instances

Function Quantity with cycle time

3 ms 8 ms

BTIGAPC – 16
GUID-B45901F4-B163-4696-8220-7F8CAC84D793 v2

Table 39. Number of IB16 instances

Function Quantity with cycle time

3 ms 8 ms

IB16 - 18
GUID-A339BBA3-8FD0-429D-BB49-809EAC4D53B0 v2

Table 40. Number of ITBGAPC instances

Function Quantity with cycle time

3 ms 8 ms

ITBGAPC - 16
GUID-B258726E-1129-47C9-94F9-BE634A2085FA v4

Table 41. Elapsed time integrator with limit transgression and overflow supervision TEIGAPC

Function Cycle time (ms) Range or value Accuracy

Elapsed time integration 3 0 ~ 999999.9 s ±0.2% or ±20 ms whichever is

greater

8 0 ~ 999999.9 s ±0.2% or ±45 ms whichever is

greater

Table 42. Number of TEIGAPC instances

Function Quantity with cycle time

3 ms 8 ms

TEIGAPC 18 36
GUID-CEA332FF-838D-42B7-AEFC-C1E87809825E v3

Table 43. Number of INTCOMP instances

Function Quantity with cycle time

3 ms 8 ms

INTCOMP – 30

32 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

GUID-3FDD7677-1D86-42AD-A545-B66081C49B47 v4

Table 44. Number of REALCOMP instances

Function Quantity with cycle time

3 ms 8 ms

REALCOMP – 30

ABB 33
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Monitoring GUID-5E04B3F9-E1B7-4974-9C0B-DE9CD4A2408F
M16080-1 v6
v5

Table 45. Supervision of mA input signals

Function Range or value Accuracy

mA measuring function ±5, ±10, ±20 mA ±0.1 % of set value ±0.005 mA

0-5, 0-10, 0-20, 4-20 mA

Max current of transducer (-20.00 to +20.00) mA

to input

Min current of transducer to (-20.00 to +20.00) mA

input

Alarm level for input (-20.00 to +20.00) mA

Warning level for input (-20.00 to +20.00) mA

Alarm hysteresis for input (0.0-20.0) mA

M12760-1 v11

Table 46. Disturbance report DRPRDRE

Function Range or value Accuracy

Pre-fault time (0.05–9.90) s -

Post-fault time (0.1–10.0) s -

Limit time (0.5–10.0) s -

Maximum number of recordings 100, first in - first out -

Time tagging resolution 1 ms See table 68

Maximum number of analog inputs 10 (internally derived) -

Maximum number of binary inputs 352 -

Maximum number of indications in a disturbance report 352 -

Maximum number of events in the Event recording per recording 150 -

Maximum number of events in the Event list 1000, first in - first out -

Maximum total recording time (3.4 s recording time and maximum number 340 seconds (100 recordings) -
of channels, typical value) at 50 Hz

Sampling rate 1 kHz at 50 Hz -

Recording bandwidth (5-300) Hz -

34 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

GUID-F034B396-6600-49EF-B0A5-8ED96766A6A0 v8

Table 47. Insulation supervision for gas medium function SSIMG

Function Range or value Accuracy

Pressure alarm level 1.00-100.00 ±10.0% of set value

Pressure lockout level 1.00-100.00 ±10.0% of set value

Temperature alarm level -40.00-200.00 ±2.5% of set value

Temperature lockout level -40.00-200.00 ±2.5% of set value

Time delay for pressure alarm (0.000-60.000) s ±0.2% or ±250ms whichever is greater

Reset time delay for pressure alarm (0.000-60.000) s ±0.2% or ±250ms whichever is greater

Time delay for pressure lockout (0.000-60.000) s ±0.2% or ±250ms whichever is greater

Time delay for temperature alarm (0.000-60.000) s ±0.2% or ±250ms whichever is greater

Reset time delay for temperature alarm (0.000-60.000) s ±0.2% or ±250ms whichever is greater

Time delay for temperature lockout (0.000-60.000) s ±0.2% or ±250ms whichever is greater
GUID-83B0F607-D898-403A-94FD-7FE8D45C73FF v8

Table 48. Insulation supervision for liquid medium function SSIML

Function Range or value Accuracy

Oil alarm level 1.00-100.00 ±10.0% of set value

Oil lockout level 1.00-100.00 ±10.0% of set value

Temperature alarm level -40.00-200.00 ±2.5% of set value

Temperature lockout level -40.00-200.00 ±2.5% of set value

Time delay for oil alarm (0.000-60.000) s ±0.2% or ±250ms whichever is greater

Reset time delay for oil alarm (0.000-60.000) s ±0.2% or ±250ms whichever is greater

Time delay for oil lockout (0.000-60.000) s ±0.2% or ±250ms whichever is greater

Time delay for temperature alarm (0.000-60.000) s ±0.2% or ±250ms whichever is greater

Reset time delay for temperature alarm (0.000-60.000) s ±0.2% or ±250ms whichever is greater

Time delay for temperature lockout (0.000-60.000) s ±0.2% or ±250ms whichever is greater
GUID-B6799420-D726-460E-B02F-C7D4F1937432 v9

Table 49. Circuit breaker condition monitoring SSCBR

Function Range or value Accuracy

Alarm level for open and close travel time (0 – 200) ms ±3 ms

Alarm level for number of operations (0 – 9999) -

Independent time delay for spring charging (0.00 – 60.00) s ±0.2% or ±30 ms whichever is greater
time alarm

Independent time delay for gas pressure (0.00 – 60.00) s ±0.2% or ±30 ms whichever is greater
alarm

Independent time delay for gas pressure (0.00 – 60.00) s ±0.2% or ±30 ms whichever is greater
lockout

CB Contact Travel Time, opening and ±3 ms

closing

ABB 35
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

M12700-1 v4

Table 50. Event list

Function Value

Buffer capacity Maximum number of events in the list 1000

Resolution 1 ms

Accuracy Depending on time synchronizing

M13765-1 v5

Table 51. Indications

Function Value

Buffer capacity Maximum number of indications presented for single disturbance 352

Maximum number of recorded disturbances 100

M12702-1 v4

Table 52. Event recorder

Function Value

Buffer capacity Maximum number of events in disturbance report 150

Maximum number of disturbance reports 100

Resolution 1 ms

Accuracy Depending on time

synchronizing
GUID-C43B8654-60FE-4E20-8328-754C238F4AD0
M12384-1 v3
v7

Table 53. Event counter with limit supervision L4UFCNT

Function Range or value Accuracy

Counter value 0-65535 -

Max. count up speed 30 pulses/s (50% duty cycle) -

GUID-2068BBA0-9026-48D0-9DEB-301BCB3C600C v1

Table 54. Voltage harmonic monitoring VHMMHAI (50/60 Hz)

Function Range or value Accuracy

Fundamental Harmonic

Frequency (0.95 - 1.05) X fr 2nd order to 5th order (0.1 - 0.5) X V ± 2 mHz

True RMS (10 to 150) V None ± 0.5%

(10 to 150) V 2nd order to 5th order (0.1 - 0.5) X V ± 2%

Fundamental (10 to 150) V None ± 0.5%

(10 to 150) V 2nd order to 5th order (0.1 - 0.5) X V ± 0.5%

Crest Factor (10 to 150) V None ± 2%

Harmonic (10 to 150) V 2nd order to 5th order (0.1 - 0.5) X V ± 4%

Amplitude

Total Harmonic (10 to 150) V 2nd order to 5th order (0.1 - 0.5) X V ± 4%
Distortion
(VTHD)

36 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Station communication M15031-1 v9

Table 55. Communication protocols

Function Value

Protocol IEC 61850-8-1

Communication speed 100BASE-FX, 100BASE-TX

Protocol TCP/IP, Ethernet

Communication speed 100BASE-FX, 100BASE-TX

Connectors Optical type LC, galvanic RJ45 shielded Ethernet connection

SEMOD55310-2 v13

Table 56. SFP - Optical ethernet port

Quantity Rated value

Number of channels Up to 6 single or 3 redundant or a combination of single and redundant links for
communication using any protocol

Standard IEEE 802.3u 100BASE-FX

Type of fiber 62.5/125 mm multimode fiber

Wave length 1310 nm, Class 1 laser safety

Optical connector Type LC

Communication speed Fast Ethernet 100 Mbit/s

Table 57. SFP - Galvanic RJ45

Quantity Rated value

Number of channels Up to 6 single or 3 redundant or a combination of single and redundant links for
communication using any protocol

Standard IEEE 802.3u 100BASE-TX

Type of cable Cat5e FTP

Connector Type RJ45

Communication Speed Fast Ethernet 100 Mbit/s

GUID-8651FF22-C007-4D53-B7E3-686A30F37CB6 v6

Table 58. Ethernet redundancy protocols, IEC 62439-3

Function Value

Protocol IEC 62439-3 Ed.1 Parallel Redundancy Protocol (PRP-0)

Communication speed 100BASE-FX, 100BASE-TX

Protocol IEC 62439-3 Ed.2 Parallel Redundancy Protocol (PRP-1)

Communication speed 100BASE-FX, 100BASE-TX

Protocol IEC 62439-3 Ed.2 High-availability Seamless Redundancy (HSR)

Communication speed 100BASE-FX, 100BASE-TX

Connectors Optical type LC, galvanic RJ45 shielded Ethernet connection

ABB 37
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Hardware
IED
M11778-1 v7 SEMOD53385-1 v1

Table 59. Case

Material Steel sheet

Surface treatment Aluzink preplated steel

Finish Light grey (RAL 7035)

M12327-1 v5

Table 60. Water and dust protection level according to IEC 60529

View IP code

Front, sides, top and IP40

bottom

Rear side IP20 with screw compression type

IP10 with ring lug terminals
M11777-1 v7

Table 61. Weight

Case size Weight

6U, 1/2 x 19” £ 7.5 kg/16 lb

6U, 1/1 x 19” £ 15 kg/33 lb

Electrical safety
GUID-1CF5B10A-CF8B-407D-8D87-F4B48B43C2B2 v2 GUID-2825B541-DD31-4DAF-B5B3-97555F81A1C2 v1

Table 62. Electrical safety according to IEC 60255-27

Quantity Rated value

Equipment class I (protective earthed)

Overvoltage category III

Pollution degree 2 (normally only non-conductive pollution occurs except that occasionally a temporary conductivity caused by
condensation is to be expected)

38 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

SEMOD53376-2
SEMOD53371-1
M12583-1 v8
v6
v1
Connection system

Table 63. Auxiliary power supply and binary I/O connectors

Connector type Rated voltage Maximum conductor area

Screw compression type 250 V AC 2.5 mm2 (AWG14)

2 × 1 mm2 (2 x AWG18)

Terminal blocks suitable for ring lug terminals 300 V AC 3 mm2 (AWG14)
GUID-96676D5D-0835-44DA-BC22-058FD18BDF34 v3

Table 64. NUM: Communication ports

Connector type Port type and number

NUM 4 Ethernet ports

4 Basic

Ethernet connection type SFP Optical LC or Galvanic RJ45

Carrier modules supported OEM

GUID-4876834C-CABB-400B-B84B-215F65D8AF92 v3

Table 65. OEM: Number of Ethernet ports

Connector type Port type and number

OEM 2 Ethernet Ports

Ethernet connection type SFP Optical LC or Galvanic RJ45

ABB 39
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Basic IED functions GUID-217F90D1-3C0F-4CD3-A54A-16C9A2760698 v2

Table 66. SAM600-IO – Typical application time delay for processing signals

Input Application Output time delay

GOOSE, receive Application (3 ms) GOOSE send 5 ms

BOM, binary 8 ms
output

SOM, static 5 ms
output

BIM, binary input GOOSE send 6.5 ms

BOM, binary 9.5 ms

output

SOM, static 6.5 ms

output
M11963-1 v5

Table 67. Self supervision with internal event list

Data Value

Recording manner Continuous, event controlled

List size 40 events, first in-first out

M12331-1 v9

Table 68. Time synchronization, time tagging

Function Value

Time tagging resolution, events and sampled measurement values 1 ms

Time tagging error with synchronization once/min (minute pulse synchronization), events and sampled ± 1.0 ms typically
measurement values

Time tagging error with SNTP synchronization, sampled measurement values ± 1.0 ms typically
GUID-8AEB81D0-1731-46DF-A206-D2E758823575 v2

Table 69. Time synchronization PTP: IEC/IEEE 61850-9-3

Data Value

Supported types of clock Boundary Clock (BC), Ordinary Clock (OC), Transparent Clock (TC)

Accuracy According to standard IEC/IEEE 61850-9-3

Number of nodes According to standard IEC/IEEE 61850-9-3

Ports supported All rear Ethernet ports

40 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

13. Ordering for customized IED GUID-046AAA27-E3DD-42B7-AFAF-DA3C83ADF797 v2

Table 70. General guidelines

Guidelines
Carefully read and follow the set of rules to ensure problem-free order management.
Please refer to the available functions table for included application functions.
PCM600 must be used to configure the IED.

Table 71. Example ordering code

To obtain the complete ordering code, please combine code from the selection tables, as given in the example below.
Example of a complete code: SAM600–IO*2.2 – F00 - H56P23P24 - AG - CA - CD1D1ARGN1N1XXXXXXX - KKKKXHPP. Using the code of each position #1-9
specified as SAM600-IO*1-2-3 3 3 –4 5-6 6-7 7 7 7 7 7 7 7 7 7 7 7 7 7 7-8 8 8 8 8 8 8 8

Product Configuratio Software options Casing and Mounting Power supply

version n alternative
# 1 - 2 - 3 - 4 5 - 6 -
SAM600–IO* 2.2 - F00 - - - -

Binary input/output module Station communication, remote end serial

communication and time synchronization
7 - 8
-

Table 72. Product definition ordering codes

Product SAM600–IO*
Product version 2.2
Configuration alternative
Switchgear control unit SAM600–IO F00
Ordering number
Switchgear control unit SAM600–IO 1MRK002850-AA

Position
Product version #1 Notes and rules
Version no. 2.2
Selection for position #1 2.2

Position
Configuration alternative Ordering no #2 Notes and rules
Switchgear control unit SAM600–IO 1MRK004250-FA F00
Selection for position #2

Position
Software options Ordering no #3 Notes and rules
No option X00 All fields in the ordering
form do not need to be
filled in.
Circuit breaker 1MRK004001-VY H56
IEC 62439-3 Parallel redundancy protocol 1MRK004001-PP P23
IEC 62439-3 High-availability seamless redundancy 1MRK004001-PR P24
Selection for position #3

Position
Casing Ordering no #4 Notes and rules
1/2 x 19" rack casing 1MRK000151-VA A
1/1 x 19" rack casing 1MRK000151-VC D
Selection for position #4

ABB 41
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Position
Mounting details with IP40 of protection from the front Ordering no #5 Notes and rules
No mounting kit included X
19" rack mounting kit for 1/2x19" case or 2xRHGS6 or RHGS12 1MRK002420-BB A
19" rack mounting kit for 1/1 19" case 1MRK002420-CA C
Wall mounting kit 1MRK002420-LA G
Selection for position #5

Position
Power supply modules Ordering no #6 Notes and rules
Compression terminals 1MRK002960-GA C
Ringlug terminals 1MRK002960-HA R
Power supply module, 24-60 VDC 1MRK002239-AB A
Power supply module, 90-250 VDC 1MRK002239-BB B
Selection for position #6

Table 73. Maximum quantity of I/O modules, with compression terminals

When ordering I/O modules, observe the maximum quantities according to the tables below.

Note: Standard order of location for I/O modules is BIM-BOM-SOM-IOM-MIM from left to right as seen from the rear side of the IED, but
can also be freely placed.
Note: The maximum quantity of I/O modules depends on the type of connection terminals.
Case sizes BIM IOM BOM/ MIM Maximum in case
SOM
1/1 x 19” rack casing 14 6 4 4 14 *)
1/2 x 19” rack casing 3 3 3 1 3
*) including a combination of maximum four modules of type BOM, SOM and MIM

Table 74. Maximum quantity of I/O modules, with ringlug terminals

Note: Only every second slot can be used.

Case sizes BIM IOM BOM MIM Maximum Notes
/SOM in case
1/1 x 19” rack casing 7 6 4 4 7 **) possible locations: P3, P5, P7, P9, P11, P13, P15
**) including a combination of maximum four modules of type BOM, SOM
and MIM

42 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Table 75. Binary input/output module selection

Binary input/ Ordering no #7 Notes and rules

output modules
Slot position 1 BIM is required in

P3/X31

P4/X41

P5/X51

P6/X61

P7/X71

P8/X81

P9/X91

P10/X101

P11/X111

P12/X121

P13/X131

P14/X141

P15/X151

P16/X161
(front view/rear position p3. 1 BOM,
view) SOM or IOM is required
but freely placed.
1/2 case █ █ █ These black marks
indicate the maximum
1/1 case █ █ █ █ █ █ █ █ █ █ █ █ █ █
number of modules
per casing type and
the slots that can be
occupied.
Compression 1MRK002960-KA C
terminals
Ringlug 1MRK002960-LA R Only valid for 1/1 x 19"
terminals rack casing .
Only every second slot
can be used; see Table
74
No board in slot X X X X X X X X X X X X X
Binary output 1MRK000614-AB A A A A A A A A A A A A A
module 24
output relays
(BOM)
BIM 16 inputs, 1MRK000508-DD B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1
RL24, 24-30VDC,
50mA
BIM 16 inputs, 1MRK000508-AD C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1
RL48, 48-60VDC,
50mA
BIM 16 inputs, 1MRK000508-BD D1 D1 D1 D1 D1 D1 D1 D1 D1 D1 D1 D1 D1 D1
RL110,
110-125VDC,
50mA
BIM 16 inputs, 1MRK000508-CD E1 E1 E1 E1 E1 E1 E1 E1 E1 E1 E1 E1 E1 E1
RL220,
220-250VDC,
50mA
BIM 16 inputs, 1MRK000508-CE E2 E2 E2 E2 E2 E2 E2 E2 E2 E2 E2 E2 E2 E2
RL220,
220-250VDC,
120mA
BIM 16 inputs, 1MRK000508-HA F F F F F F F F F F F F F F
RL24, 24-30VDC,
50mA, enhanced
pulse counting
BIM 16 inputs, 1MRK000508-EA G G G G G G G G G G G G G G
RL48, 48-60VDC,
50mA, enhanced
pulse counting
BIM 16 inputs, 1MRK000508-FA H H H H H H H H H H H H H H
RL110,
110-125VDC,
50mA, enhanced
pulse counting
BIM 16 inputs, 1MRK000508-GA K K K K K K K K K K K K K K
RL220,
220-250VDC,
50mA, enhanced
pulse counting
IOM 8 inputs, 1MRK000173-GD L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1
10+2 outputs,
RL24, 24-30VDC,
50mA
IOM 8 inputs, 1MRK000173-AE M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 M1
10+2 outputs,
RL48, 48-60VDC,
50mA

ABB 43
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Table 75. Binary input/output module selection, continued

Binary input/ Ordering no #7 Notes and rules
output modules
IOM 8 inputs, 1MRK000173-BE N1 N1 N1 N1 N1 N1 N1 N1 N1 N1 N1 N1 N1
10+2 outputs,
RL110,
110-125VDC,
50mA
IOM 8 inputs, 1MRK000173-CE P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1
10+2 outputs,
RL220,
220-250VDC,
50mA
IOM 8 inputs 1MRK000173-CF P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2
10+2 outputs,
RL220,
220-250VDC,
110mA
IOM with MOV 8 1MRK000173-GC U U U U U U U U U U U U U
inputs, 10+2
outputs, RL24,
24-30VDC, 50mA
IOM with MOV 8 1MRK000173-AD V V V V V V V V V V V V V
inputs, 10+2
outputs, RL48,
48-60VDC,
50mA
IOM with MOV 8 1MRK000173-BD W W W W W W W W W W W W W
inputs, 10+2
outputs, RL110,
110-125VDC,
50mA
IOM with MOV 8 1MRK000173-CD Y Y Y Y Y Y Y Y Y Y Y Y Y
inputs, 10+2
outputs, RL220,
220-250VDC,
50mA
mA input 1MRK000284-AB R R R R R R R R R R R R R
module MIM 6
channels
SOM Static 1MRK002614-BA T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 SOM not allowed in
output module, position nearest NUM
12 outputs; 6 board. Position
standard relays depending on case
+ 6 static size.
outputs,
48-60VDC
SOM Static 1MRK002614-CA T2 T2 T2 T2 T2 T2 T2 T2 T2 T2 T2 T2
output module,
12 outputs; 6
standard relays
+ 6 static
outputs,
110-250VDC
Selection for position #8

44 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Table 76. Station communication

Station communication, remote end serial communication and Ordering no #8 Notes and rules
time synchronization
Slot position (front view/rear view)

P30:1/X301

P30:2/X302

P30:3/X303

P30:4/X304

P30:5/X305

P30:6/X306

P30:6:1/X3061

P30:6:2/X3062
Available slots in 1/2 and 1/1 case █ █ █ █ █ █ █ █
No communication board included X X X X
Ethernet SFP, optical LC connector 1MRK005500-AA K K K K K K Ethernet SFP is basic
in P30:1, P30:2, P30:3
Ethernet SFP, RJ45 connector 1MRK005500-BA P P P P P P
and P30:4. P30:6:1 and
P30:6:2 require the
Optical Ethernet
module in P30:6.
Optical Ethernet module 1MRK002266-EA H
Selection for position #9

ABB 45
© Copyright 2017 ABB. All rights reserved
Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

14. Ordering for Accessories

Accessories IP15151-1 v1
Protection cover
M15040-3 v7

Protective cover for rear side of terminal, 6U, 1/2 x 19” Quantity: 1MRK 002 420-TA

Protective cover for rear side of terminal, 6U, 1/1 x 19” Quantity: 1MRK 002 420-RA

Combiflex
SEMOD130267-5 v8 IP15161-1 v1

Mounting kit
Side-by-side mounting kit Quantity: 1MRK 002 420-Z

SAM600-IO LHMI service kit

GUID-AA273B49-34F4-4F54-8F22-F4A4261785A6 v2

SAM600-IO LHMI service kit Quantity 1MRK 000 028-SA

:

Manuals M15161-3 v15

User documentation
Rule: Specify the number of printed manuals requested
Application manual IEC Quantity 1MRK 511 445-UEN
:

Technical manual IEC Quantity 1MRK 511 446-UEN

:

Commissioning manual IEC Quantity 1MRK 511 447-UEN

:

Communication protocol manual, IEC 61850 Edition 1 IEC Quantity 1MRK 511 440-UEN
:

Communication protocol manual, IEC 61850 Edition 2 IEC Quantity 1MRK 511 441-UEN
:

Operation manual IEC Quantity 1MRK 500 131-UEN

:

Installation manual IEC Quantity 1MRK 514 030-UEN

:

Engineering manual IEC Quantity 1MRK 511 442-UEN

:

Cyber security deployment guideline IEC Quantity 1MRK 511 443-UEN

:

46 ABB
© Copyright 2017 ABB. All rights reserved
 Switchgear control unit SAM600-IO 1MRK 511 448-BEN C
Version 2.2

Reference information M2175-3 v4

For our reference and statistics we would be pleased to be provided with the following application data:

Country: End user:

Station name: Voltage level: kV

Related documents GUID-94E8A5CA-BE1B-45AF-81E7-5A41D34EE112 v7

Documents related to SAM600–IO Document numbers

Application manual 1MRK 511 445-UEN

Commissioning manual 1MRK 511 447-UEN

Product guide 1MRK 511 448-BEN

Technical manual 1MRK 511 446-UEN

Type test certificate 1MRK 511 448-TEN

Operation manual 1MRK 500 131-UEN

Engineering manual 1MRK 511 442-UEN

Installation manual 1MRK 514 030-UEN

Communication protocol manual, 1MRK 511 440-UEN

IEC 61850 Edition 1

Communication protocol manual, 1MRK 511 441-UEN

IEC 61850 Edition 2

Cyber security deployment 1MRK 511 443-UEN

guideline

Accessories guide IEC: 1MRK 514 012-BEN

ABB 47
© Copyright 2017 ABB. All rights reserved
48
ABB AB
Grid Automation Products
SE-721 59 Västerås, Sweden
Phone +46 (0) 21 32 50 00
Scan this QR code to visit our website
www.abb.com/protection-control
1MRK 511 448-BEN

© Copyright 2017 ABB.

All rights reserved.