Salwico Cargo

Conventional Fire Detection

System
Quick Guide
Consilium Marine & Safety AB
Fire & Gas Marine Division
Phone: +46 31 710 77 00
Fax: +46 31 710 78 00
E-mail: Service: [email protected]
Spares: [email protected]

Consilium Marine & Safety AB

Navigation Division
Phone: +46 8 563 05 100
Fax: +46 8 563 05 199
E-mail: Service, APT: [email protected]
Spares: [email protected]

The contents of this document are subject to revision without notice

due to continued progress in methodology, design and manufacturing.
Consilium assumes no legal responsibility for any error or damage
resulting from the usage of this document.

April 2010
Document no. 5100336-02A01
Part no: 5100336

© 2009-2010, Consilium AB
Quick Guide Quick Guide for Control Panel M 4.3

Quick Guide for Control Panel M 4.3

5100336-02A01 1
Quick Guide for Control Panel M 4.3 Quick Guide

2 5100336-02A01
Global Service and Support

Own companies
Sales- and service representatives

Consilium is constantly increasing and improving its global sales and service
organisation in order to provide our customers with the most competent
service and support. Today Consilium has established own companies in
16 countries plus sales and service representatives in more than 50 countries.
You will find updated contact information on our web-site www.consilium.se.

www.consilium.se
 Salwico Cargo
Conventional Fire Detection
System
User Guide
Consilium Marine & Safety AB
Fire & Gas Marine Division
Phone: +46 31 710 77 00
Fax: +46 31 710 78 00
E-mail: Service: [email protected]
Spares: [email protected]

Consilium Marine & Safety AB

Navigation Division
Phone: +46 8 563 05 100
Fax: +46 8 563 05 199
E-mail: Service, APT: [email protected]
Spares: [email protected]

Consilium Marine & Safety AB

Transport Division
Phone: +46 31 710 77 00
Fax: +46 31 710 78 00
E-mail: Service: [email protected]
Spares: [email protected]

The contents of this document are subject to revision without notice

due to continued progress in methodology, design and manufacturing.
Consilium assumes no legal responsibility for any error or damage
resulting from the usage of this document.

January 2012
Document no. 5100332-02B02
Part no. Part no: 5100332

© 2009-2012, Consilium Marine & Safety AB

 Table of contents

1 Introduction ...................................................................................... 1
1.1 About This Manual .......................................................................... 1
1.2 Approvals .......................................................................................... 2

2 Symbols Used in the Manual ........................................................... 3

3 Fire Detection System ...................................................................... 5

3.1 System Description ........................................................................... 5
3.2 System Block Diagram ..................................................................... 5

4 Control Panels .................................................................................. 7

4.1 Control Panel M 4.3 ......................................................................... 7
4.1.1 General ........................................................................................... 7
4.1.2 Description of Keys and Indicators ................................................ 7
4.1.3 Guide to the Menu System ............................................................. 11

4.2 Repeater M 4.3 ................................................................................. 20

4.2.1 General ........................................................................................... 20
4.2.2 Description of Keys and Indicators ................................................ 21

5 Operations ........................................................................................ 23
5.1 Access Levels .................................................................................... 23
5.2 Login ................................................................................................. 24
5.3 Fire Alarm ........................................................................................ 24
5.3.1 Information Displayed when “Fire” is Flashing ............................ 24
5.3.2 Mute a Fire Alarm .......................................................................... 25
5.3.3 Reset a Fire Alarm ......................................................................... 25
5.3.4 Several Alarms ............................................................................... 25
5.3.5 Type of Fire Alarms from Conventional Zones ............................. 25

5.4 Fault Indications .............................................................................. 25

5.4.1 Information Displayed when “Fault” is Flashing .......................... 25
5.4.2 Mute a Fault ................................................................................... 26
5.4.3 Reset a Fault ................................................................................... 26
5.4.4 Reset a Fault from the Fault List .................................................... 26
5.4.5 Reset All Faults .............................................................................. 27

5.5 Fault Messages ................................................................................. 27

5.6 Disablements .................................................................................... 27
5.6.1 About Disablements ....................................................................... 27
5.6.2 Available Disablements ................................................................. 27
5.6.3 Acknowledgement of a New Disablement .................................... 28
5.6.4 Disabling Zones ............................................................................. 28
5.6.5 Disabling Alarm Devices ............................................................... 28
5.6.6 Old Disablements ........................................................................... 29
5.6.7 Alarm Delay ................................................................................... 29
5.6.8 Disabling External Outputs ............................................................ 29
Table of contents

5.6.9 Disabling an Alarm Transfer Output ............................................. 30

5.7 Reconnecting .................................................................................... 30

5.7.1 Reconnecting Disabled Items ........................................................ 30
5.7.2 Reconnecting Periodic Disablements ............................................ 30
5.7.3 Remove All Disablements ............................................................. 30

5.8 Service Menu .................................................................................... 30

6 Testing ............................................................................................... 33
6.1 About Testing .................................................................................... 33
6.2 Test Mode Overview ......................................................................... 33
6.3 Testing a Fire-detecting Zone .......................................................... 33
6.4 Recommended Test Equipment ........................................................ 34
6.5 Reset Test Mode ................................................................................ 34
6.6 Test the Control Panel Display ........................................................ 34

7 Appendix ........................................................................................... 35
7.1 Fault Code List ................................................................................. 35
7.2 Definitions of Terms ......................................................................... 40

8 Quick Guide for Control Panel M 4.3 ............................................. 45

Index ................................................................................................. 47
User Guide 1 Introduction

1 Introduction

1.1 About This Manual

This User Guide is intended for personnel using the Fire detection system and
provides basic understanding how to operate the system.

NOTE!
This guide is valid for Control panel software versions beginning with version
1.0.0.

The chapter Fire Detection System gives general information about the system.

The chapter Control Panels describes the function of the Control panel and the
Repeater in the Fire detection system.

The chapter Operations describes how to operate the Fire detection system.

The chapter Testing provides brief instructions on how to connect and test the
system (detailed information is found in the Service & Maintenance manual).

The Fault Code List in the Appendix lists the different fault codes.

Figure 1. Salwico Cargo Fire Detection System, an example.

5100332-02B02 1
1 Introduction User Guide

1.2 Approvals

2 5100332-02B02
User Guide 2 Symbols Used in the Manual

2 Symbols Used in the Manual

DANGER!
Risk of serious or fatal injury to the user, and/or severe damage to the product, if
the instructions are not followed.

WARNING!
Risk of personal injury and/or damage to the product if the instructions are not
followed.

CAUTION!
Risk of minor or moderate personal injury. Risk of equipment damage, loss of data,
extra work, or unexpected results, if the instructions are not followed.

NOTE!
Note symbols alert you to important facts and conditions.

Hint
Tip symbols direct you to specific instructions, such as where to find additional
information and tell you how to perform a certain operation in an easier way.

5100332-02B02 3
2 Symbols Used in the Manual User Guide

4 5100332-02B02
User Guide 3 Fire Detection System

3 Fire Detection System

3.1 System Description

This Fire detection system is a state-of-the-art fire-detection system designed to
meet marine and industrial requirements. Special care is given to ergonomics and
user-friendliness with its logical and intuitive operator panel.

3.2 System Block Diagram

The following figure shows a typical system and its connected components, see
Definitions of Terms, page 40 in the Appendix for explanation of terms and
abbreviations.

Figure 2. An example of a system block diagram.

5100332-02B02 5
3 Fire Detection System User Guide

6 5100332-02B02
User Guide 4 Control Panels

4 Control Panels

4.1 Control Panel M 4.3

4.1.1 General
This menu-operated system monitors and controls all system functionality. The
control panel's clear graphical display makes it easy to use.

4.1.2 Description of Keys and Indicators

Figure 3. Keys and indicators for the control panel

As shown in the figure above, the control panel is divided into three sections:

A = System Indicators
B = Operational Controls
C = Numerical Keypad

Part A: System Indicators

Figure 4. The system indicators section of the control panel

5100332-02B02 7
4 Control Panels User Guide

The System Indicators section is comprised of the following indicators:

1. Power
Steady green light Power supply to the control panel is OK.

2. System fault
Main process fault. A serious system fault in the
Flashing yellow light
system.

3. Test
Steady yellow light At least one zone is manually set in test mode.

4. Warning
Steady yellow light At least one warning indication exists.

5. Zone
Steady yellow light At least one zone or a fire detector is disabled.
At least one zone or a fire detector is in fault condition.
Flashing yellow light
(Priority over disablement indication.)

6. Alarm device
At least one alarm device output (e.g., a bell) is
Steady yellow light
disabled.
Flashing yellow light At least one alarm device output is in fault condition.

7. Alarm delay off

Steady yellow light The alarm delay function is disabled.

8. Custom indication 1-3

Colour and pattern of Custom LED indication is depending on system configuration.

9. USB
USB connection for flash memories to load or save a configuration file.

8 5100332-02B02
User Guide 4 Control Panels

Part B: Operational Controls

Figure 5. The operational section of the control panel

1. Main indicators
Fire alarm
The Fire alarm button indicates existance of a fire alarm and gives direct access
to the Fire alarm list.
Indications:
Flashing red light An un-muted fire alarm in the system.
Steady red light All fire alarms are muted.

Pre-Alarm
Note! Only for analogue addressable systems.
The Pre-Alarm button indicates existance of a pre-alarm and gives direct access
to the Pre-Alarm list.
Indications:
Flashing orange light An un-muted pre-alarm in the system.
Steady orange light All pre-alarms are muted.

Fault
The Fault button indicates existance of a fault and gives direct access to the
Fault alarm list.
Indications:
Flashing yellow light An un-muted fault in the system.
Steady yellow light All faults are muted.

Disablements
The Disablements button indicates existance of a disablement and activates the
Disablements menu.
Indications:
Steady yellow light At least one disabled function in the system.

Shortcuts
The Shortcut button activates the customer specific shortcut list.

5100332-02B02 9
4 Control Panels User Guide

Indications:
Steady orange light The alternatives in the shortcut list and the
corresponding indicators (Shortcut 1, Shortcut 2 and
Shortcut 3) are programmed via the definition
program.

2. Status
This button gives direct access to the System status summary list with Alarms
(Fire and Pre-Alarms), Maintenance (Faults and Warnings) and Disablements
(Active and Periodic).
Shortcuts are:
1. Upload the system log to USB Memory stick.
2. Go to the maintenance menu.

3. Menu
This button gives direct access to the main menu and all system functions.
4. Navigation and Command Keys
The arrow keys are used to navigate menus, select different menu alternatives,
and show details for list items.
Go to the previous item in the list or
menu.

Selects the chosen menu

Go to previous menu.
alternative.

Go to the next item in the list or

menu.

ESC
The Escape button is used to go to the top menu screen.

OK
This button is used to select a menu alternative or to accept a function. The OK button
is also in some cases used to show details for a selected list entry.

5. Display
The display has a backlited 4.3" graphical screen, 480×272, 16-bit colour
screen.
6. Alarm buttons
Multiple alarms
Press this button to scroll through the different alarms. The list always returns to the
first fire alarm after 30 seconds of inactivity.

Reset

10 5100332-02B02
User Guide 4 Control Panels

This green button is used to reset a selected alarm, fault or disablement.

Mute
This red button is used to mute (acknowledge) and silence alarms.

Part C: Numerical Keypad

Figure 6. The keypad on the control panel.

1. Numerical keypad
Keys 0 - 9
The numerical keypad is used to enter numerical values. Keys 1–9 are also used as
shortcuts when navigating in the menus.

Erase
This button is used to erase characters from the text display.

Enter
This button is used to select a menu alternative or to accept a function. The Enter
button is also used to show details for a selected list entry.

Day mode
Increase the brightness/contrast level for the indicators and display on the panel.

Night mode
Decrease the brightness/contrast level for the indicators and display on the panel.

4.1.3 Guide to the Menu System

4.1.3.1 General
The Fire detection system is menu-operated. All system functions are available
from the different menus.

5100332-02B02 11
4 Control Panels User Guide

Figure 7. Menu tree screen.

4.1.3.2 Choosing Menu Alternatives

1 Press Menu to enter the menu system
2 Navigate in the menu alternatives with the and arrows.
3 Choose a menu alternative with the arrow and go to the previous menu
alternative using the arrow.

It is also possible to choose a menu alternative by entering the menu number.

In the lower part of the display the different options available for each individual
menu are shown.

The numerical keypad is used to enter information, e.g., zone and detector number.

The button erases the last character.

4.1.3.3 Menu Tree

Hint
This section lists the available system menus. The bracketed number following
each menu refers to corresponding menu in the Explanation of the Different Menu
Alternatives, page 15.

NOTE!
All menus are shown in the system, as described below. But depending on the
actual system configuration some menu alternatives can have limited function.

1 Fault Alarms (1)

1 Fault List* (1.1)
Mute
Reset
2 Warning List* (1.2)
3 Reset All Faults (1.3)

2 Fire Alarms (2)

12 5100332-02B02
User Guide 4 Control Panels

1 Fire List* (2.1)

Mute
Reset
0 Disable
2 Pre-Alarm List* (2.2)
3 Resound (restart bells) (2.3)
4 Reset All Fire Alarms (2.4)

3 Disablements (3)
1 New disablement1 (3.1)
1 Zones (3.1.1)
Choose Zone and Zone Type

1 Permanent disablement
2 Timer disablement
3 Clock disablement
4 Periodic disablement
2 Detectors & Manual Call Points (3.1.2)
Note! Only for analogue addressable systems
Choose Zone, Detector Type and Detector

1 Permanent disablement
2 Timer disablement
3 Clock disablement
4 Periodic disablement
3 External Controls (3.1.3)
1 External Controls (3.1.3.1)
1 All groups (Doors, Fire, etc.) (3.1.3.1.1)
2 Doors (3.1.3.1.2)
3 Fire (3.1.3.1.3)
4 Fault (3.1.3.1.4)
5 Ventilation (3.1.3.1.5)
6 Indication (3.1.3.1.6)
2 Alarm Transfer (3.1.3.2)
4 Alarm Device (Bells etc.) (3.1.4)
5 Alarm Delay (3.1.5)
1 Permanent disablement
2 Timer disablement
3 Clock disablement
4 Periodic disablement
6 Test Mode (3.1.6)
2 Disablement list* (3.2)
1 Reset (reconnect) (3.2.1)
3 Periodic Disable list* (3.3)
4 Old Disablements (3.4)
5 Remove all disablements (3.5)

5100332-02B02 13
4 Control Panels User Guide

4 Login (4)

5 Settings (5)
1 Set Dimmer (5.1)
2 Set Time (5.2)
3 Set Date (5.3)
4 Test display (5.4)
5 Alarm Delay Times2 (5.5)
1 Alarm Delay Time 1 (mute)
2 Alarm Delay Time 2 (reset)
6 Keyboard Beep (5.6)
7 Cause Effect in Test Mode (5.7)

6 Service Menu3 (6)

1 System Details (6.1)
2 Centrals* (6.2)
2 Modules
Includes the same system menus as “Modules” below

3 Modules* (6.3)
0 Disable Modules
2 Module Inputs
0 Disable
2 Set Input
3 Clear Input
3 Module Outputs
0 Disable
2 Set Output
3 Clear Output
4 Loops
Select Loop Units (only when addressable loop)

0 Disable Loop Unit

2 Set In Fire (simulate fire alarm)
3 Erase Loop Unit
4 Zones* (6.4)
0 Disable Zone
2 Loop Units (only when addressable zone)
0 Disable Loop Unit
2 Set In Fire (simulate fire alarm)
3 Erase Loop Unit
4 Change supplementary text
5 Loops* (6.5)
0 Disable Loop
2 Loop Units (only when addressable loop)
0 Disable Loop Unit

14 5100332-02B02
User Guide 4 Control Panels

2 Set In Fire (simulate fire alarm)

3 Erase Loop Unit
3 Add Unit
4 Scan Loop Units
6 Configuration
1 Reload configuration (6.6)
1 Load entire configuration (6.6.1)
2 Load Supplementary Texts only (6.6.2)
2 Load configuration from USB Memory (6.7)
3 Save configuration to USB Memory (6.8)
4 Save changes to configuration (6.9)
5 Synchronize system configuration (6.10)
6 Reboot system (excluding myself) (6.11)
7 Reboot myself (6.12)
7 Firmware
1 Download Firmware to modules (6.13)
2 Modules
Program selected Module with Firmware

2 Load Service Pack from USB Memory

3 Backup Service Pack to USB Memory
8 System Log (6.14)

7 History (7)
1 Fire History List* (7.1)
2 Fault History List* (7.2)
3 Disable History List* (7.3)
4 Common History List* (7.4)

8 Maintenance (8)
Note! Only for analogue addressable systems
1 Lightly Contaminated Detectors (8.1)
2 Heavily Contaminated Detectors (8.2)

Footnotes for the menu tree:

* All lists can be printed by pressing 1 on the numerical keypad. It is also possible to
monitor details about the list objects by pressing the button.
1 Access level 2B
2 Access level 3
Access level 2 for basic functions, but access level 4 is needed to perform advanced
3
service options.

4.1.3.4 Explanation of the Different Menu Alternatives

The menu alternatives for the Fire detection system are described and listed by the
area in which they appear.

5100332-02B02 15
4 Control Panels User Guide

Home
The top-level menu displays system and the name of the installation (if defined).

Fault Alarms
1 Fault Alarms
The menu from which fault- and warning messages are listed and handled.
1.1 Fault List
Shows all present fault indications.
1.2 Warning List
Shows all present warning messages, for instance a dirty detector.
1.3 Reset All Faults
The system will attempt to reset all present fault alarms in the Fault List (1.1).

Fire Alarms
2 Fire Alarms
Fire alarms and pre-alarms are displayed and managed from this menu. Muted
alarm devices may be reactivated here.
2.1 Fire List
Shows all present Fire Alarms.
2.2 Pre-Alarm List
Shows all present Pre-Alarms.
2.3 Resound (restart bells)

If the alarm devices have been silenced by pressing Mute button , this
function will restart them (if the fire alarm has not been reset).
2.4 Reset All Fire Alarms
The system will attempt to reset all Fire Alarms in the Fire List (2.1)

Disablements
3 Disablements
Disablemented parts of the Fire detection system are added, removed, or listed
from this menu. (For instructions, see Disablements, page 27.)
3.1 New Disablements (access level 2B)
Adds new disablements.
3.1.1 Zones
Disable entire zones for a specified time period or permanent.
3.1.2 Detectors & Manual Call Points
Note! Only for analogue addressable systems.
Disable individual detectors or manual call points for a specified time period or
permanent.
3.1.3 External Control
Deactivate External Controls or an Alarm Transfer.
3.1.3.1 External Controls
Disables outputs (all or individual categories) to external controls. This means
that an alarm condition will not cause activation of the selected category.

16 5100332-02B02
User Guide 4 Control Panels

3.1.3.1.1 All groups (Doors, Fire, etc.)

Category including all external controls (doors, fire, fault, ventilation and
indication).
3.1.3.1.2 Doors
Disable external door controls in the system.
3.1.3.1.3 Fire
Disable external fire controls in the system.
3.1.3.1.4 Fault
Disable external fault controls in the system.
3.1.3.1.5 Ventilation
Disable external ventilation controls in the system.
3.1.3.1.6 Indication
Disable external indication controls in the system.
3.1.3.2 Alarm Transfer
Disables the supervised alarm transfer output, which is normally used in
on-shore installations to alert the fire brigade in case of a fire alarm.
3.1.4 External Device (Bells etc.)
Disables the outputs for alarm devices, such as audible (e.g., bells) and optical
alarm devices.
3.1.5 Alarm Delay
Disables the alarm delay function.
Alarm delay is a programmable time delay between when a fire is detected and
until the alarm device outputs are activated.
The alarm delay function is normally enabled.
See Alarm Delay, page 29 for more information.
3.1.6 Test Mode
Set a zone into test mode. See section Test Mode Overview, page 33 for more
details.
3.2 Disablement list
Shows all active disablements in the system. A periodic disablement (3.3) that
is not active will not be shown in this list. The reconnection of a disabled unit is
made from this list. See section Reconnecting Disabled Items, page 30 for
more details.
3.2.1 Reset

Reset the disablements by pressing the button on the control panel.

3.3 Periodic Disable list
Shows all periodic disablements in the system. The removal of periodic
disablements is made from this list.
3.4 Old Disablements
This list displays the 150 previously removed disablements and allows these
older disablements to be reactivated.
Hint
This function is very useful if the same disablement is frequently
needed during irregular time periods. Just mark the appropriate old
disablement in the list and press 0 to reactivate it.
3.5 Remove all disablements

5100332-02B02 17
4 Control Panels User Guide

Removes all active disablements shown in the Disablement list (3.2).

NOTE!
Periodic disablements (3.3) are not permanently removed. Only the
periodic disablement's active period is removed.

Login
4 Login
Log in from this menu by entering a personal access code. For further details see
section Login, page 24.

Settings
5 Settings
Use this menu to adjust system parameters, such as the dimmer level, date, time
and alarm delay time.
It is also possible to make a lamp test for the control panel under “Test display”
(5.4).
5.1 Set Dimmer
Use this menu to adjust the contrast level (1–9) for the display and indications on
the control panel.
5.2 Set Time
Use this menu to set the system time.
It is possible to synchronize the system clock with the ship's central time.
5.3 Set Date
Use this menu to set the system date.
5.4 Test display
Use this menu to activate a lamp test that verifies correct function of the display
and all indications on the control panel.
5.5 Alarm Delay Times (access level 3)
Use this menu to adjust the programmable alarm delay time (max 2 minutes).
5.6 Keyboard Beep
Use this menu to turn the keyboard beep ON or OFF.
5.7 Cause Effect in Test Mode
Use this menu to turn the Cause Effect programming ON or OFF during test
mode. If set to ON, the outputs are activated as normal during test mode.

Service Menu
Service Menu (access level 2 for basic functions, but access level 4 is needed to
6
perform advanced service options)
Use this menu to list and view information about the system and its components.
It is also possible to make disablements of the listed units. The Service menu is
described in more detail in the separate Service and Maintenance manual.
6.1 System Details
This menu lists the installed system's information, such as name and reference
number (if defined). It also lists when the system was last configured and by
which program.
6.2 Centrals
Use this menu to list information about the installed centrals and the modules in
each central.

18 5100332-02B02
User Guide 4 Control Panels

6.3 Modules
Use this menu to list information about the installed system modules. It is
possible to display all details about the modules, such as installed detector loops,
installed program versions, input/output status. It is also possible to print
information.
6.4 Zones
This menu shows a list of all zones configured in the system. It is possible to list
all loop units in a zone if the zone consists of addressable loop units, disable
zones or loop units, and set a single fire detector in alarm condition.
6.5 Loops
This menu shows a list of all physical loops installed in an analogue addressable
system. A loop can consist of conventional or addressable fire alarm detectors
and other loop units. It is also possible to disable entire loops. Use Scan Loop to
scan the loop for new loop units.
6.6 Reload configuration
Reload the configuration when a new updated configuration file or
supplementary text file has been downloaded to the system.
6.6.1 Load entire configuration
Use this command to reload the configuration. The system will restart.
6.6.2 Load Supplementary Texts only
Use this command to reload all supplementary texts from the configuration file
without a system restart.
6.7 Load configuration from USB Memory
Download a new configuration file from a suitable USB Memory stick.
6.8 Save configuration to USB Memory
Copy the existing configuration file to a suitable USB Memory stick.
6.9 Save changes to configuration
CAUTION!
It is highly recommended to backup the Configuration File before
continuing.
Use this command to save all changes made from the control panel to the system
configuration.
NOTE!
The changes are not permanently saved in the configuration file until this
command is performed.
6.10 Synchronize system configuration
CAUTION!
It is highly recommended to backup the Configuration File before
continuing.
Use this command to synchronise the Configuration Files in the system.
6.11 Reboot system (excluding myself)
This operation will reboot all Control Modules in the system.
NOTE!
The Control Module used for this procedure will not reboot.
6.12 Reboot myself
The operation will reboot this Control Module only.
6.13 Download Firmware to modules
Use this command to overwrite the firmware in the chosen Module

5100332-02B02 19
4 Control Panels User Guide

6.14 System Log

Once the System Log is copied to the USB Memory, it can be sent to an
authorized service organization for further technical assistance.

History
7 History
Use this menu to view previous events in the Fire detection system.
7.1 Fire History List
Shows a chronological list of the last 200 fire alarms.
7.2 Fault History List
Shows a chronological list of the last 200 fault alarms.
7.3 Disable History List
Shows a chronological list of the last 200 disablements.
7.4 Common History List
Shows a common chronological list of the last 1000 pre-alarms, fire alarms, fault
alarms, disablements, warnings, and I/Os.

Maintenance
8 Maintenance
Note! Only for analogue addressable systems.
Use this menu for monitoring detectors that may need maintenance.
8.1 Lightly Contaminated Detectors
Shows a list of lightly contaminated detectors for the entire system.
8.2 Heavily Contaminated Detectors
Shows a list of heavily contaminated detectors for the entire system.

4.2 Repeater M 4.3

4.2.1 General
The repeater panel is used to monitor functions in the Fire detection system. It is
possible to view and list:

• Fire alarms
• Faults
• Disablements

20 5100332-02B02
User Guide 4 Control Panels

4.2.2 Description of Keys and Indicators

Figure 8. Keys and indicators for the repeater panel.

Repeater panel
• Power
Green steady light indicates that the power supply to the repeater panel is OK.

• Local Mute
Silence the local buzzer alarm.

• Fire - Fault - Dis.

Press the button to select the lists: Fire Alarm, Fault Alarm and Disablements.

• Navigation key – previous

Scroll to previous item in the selected list.

• Navigation key – next

Scroll to next item in the selected list.

• Night mode
Decrease the brightness/contrast level for the indicators and display on the panel.

• Day mode
Increase the brightness/contrast level for the indicators and display on the panel.

• Lamp test
When you press the buttons for Day and Night mode at the same time, all the repeater
panel indicators and the display are lit – if not, they are not working correctly.

5100332-02B02 21
4 Control Panels User Guide

22 5100332-02B02
User Guide 5 Operations

5 Operations

5.1 Access Levels

To prevent un-authorized operation of the system access levels protect the different
functions of the Fire detection system.

The user has to log in to the system before any vital operations can be performed.
Without access to an authorization code the user can only view fire and fault
alarms and mute the local buzzer.

Access level 2B is the default level. The system automatically returns to access
level 2B after 30 minutes of inactivity.

Description of Access levels

There are different access levels as shown in the following table:

Table 1. Access levels

Access Procedure to enter level User Permissions
level
2B Operator access level Personnel trained and authorized to For viewing of fire or fault alarms:
None operate the system in case of fire or • Fire alarms have priority over
maintenance. fault alarms.
• Possibility to mute local
buzzer.
• Access to the menu system
• List status
• Reset and muting of alarms
• Make disablements

3 Power User access level Personnel trained and authorized to Same permissions as level 2B, plus
Enter access code for level 3 via make changes to the configured these additional permissions:
menu/login. system. • Possibility to make changes to
the configured system

4 Service access level Only authorized service personnel All functions available, including
Enter access code for level 4 via trained by an authorized service advanced service options.
menu/login. organization.

Custom Specific Restrictions

NOTE!
Permissions on the different access levels can in some cases vary depending on
programmed custom specific restrictions.

A Control Panel M 4.3 could be programmed to view events in the system with
restricted rights to operate functions. For example a fire alarm is shown, but mute
and reset are not allowed.

5100332-02B02 23
5 Operations User Guide

5.2 Login
Each user is assigned to a specific access level.

The predefined users are assigned the following default access codes:

Level 2B 2222
Level 3 3333

To log in to the system:

1 Go to Menu » 4 Login and select user.

2 Enter the four-digit access code for the The system will acknowledge
user. if the correct code is entered.

5.3 Fire Alarm

5.3.1 Information Displayed when “Fire” is Flashing
The following sections describes the information displayed during a fire alarm,
how to mute and reset an alarm, and the different types of alarms.

Figure 9. A fire alarm is detected in the system.

The following information is displayed in the Control Panel:

• Number of alarm(s)
• First, last and current list entry
• Zone in alarm
• Supplementary text (if defined in system configuration)

Press for more details:

• Time of alarm
• Date of alarm

24 5100332-02B02
User Guide 5 Operations

5.3.2 Mute a Fire Alarm

The Mute button has different functions depending on the current access level.

1 Press Access level 2B or higher:

Silences the internal buzzer
and all external alarm
devices*, and mutes the fire
alarm indication. The fire
indicator stops flashing, but
remains lit until the Fire
Alarm is reset.
2 Press for more details.

* Programmable function of external devices, programmed by system

Cause/Effect.

5.3.3 Reset a Fire Alarm

1 Press to reset the current Fire Alarm. NOTE!
Alarms cannot be
reset as long as the
device remains in
alarm condition.

5.3.4 Several Alarms

If there is more than one fire alarm in the system, the indication is activated.
The first and last fire alarms are always displayed in the control panel.

1 Scroll through the different fire alarms with

the button or the / arrow keys.
2 Mute and reset as above. For detailed instructions, see
Mute a Fire Alarm, page 25
and Reset a Fire Alarm, page
25.

5.3.5 Type of Fire Alarms from Conventional Zones

The Fire detection system will display whether a detector or a manual call point
generated the fire alarm. If two or more detectors are activated in the same zone,
the fire alarm will be presented as a manual call point/multiple detectors.

5.4 Fault Indications

5.4.1 Information Displayed when “Fault” is Flashing
The following sections describe the information that displays when a fault occurs,
and how to mute and reset a fault.

5100332-02B02 25
5 Operations User Guide

Figure 10. A fault is detected in the system.

The following information is displayed in the Control Panel:

• Number of detected fault(s)

• Type of fault
• Identification of the faulty unit
• Supplementary text for the faulty unit (if defined in system configuration)

Press for more details:

• Time when fault occurred

• Date when fault occurred
• Supplementary text about location of fault (if defined in system configuration)

5.4.2 Mute a Fault

1 Press to silence internal buzzer and mute all faults in list.
2 Press for more details.

5.4.3 Reset a Fault

1 Press to reset the current fault alarm. NOTE!
If the cause of the
fault alarm remains,
the alarm cannot be
reset. Check the fault
code in the Fault Code
List, page 35 to
solve the problem.

5.4.4 Reset a Fault from the Fault List

All faults in the system are shown in the fault list.

26 5100332-02B02
User Guide 5 Operations

1 Go to the fault list under: Menu » 1Fault

Alarms » 1 Fault List
2 Choose the fault in the fault list and then NOTE!
press to reset the fault alarm. If the cause of the
fault alarm remains,
the alarm cannot be
reset. Check the
problem, solve it, and
reset the fault.

5.4.5 Reset All Faults

1 Go to: Menu » 1 Fault Alarms » 3 Reset All
Faults
2 Press The system will make an
attempt to reset all faults.

5.5 Fault Messages

The control panel displays a fault with information about where in the system the
fault occurred and a short description of that fault.

See Fault Code List, page 35 for a list of all fault messages.

5.6 Disablements
5.6.1 About Disablements
It is possible to disable different devices attached to the system, such as zones,
alarm devices and external control devices.

All disablements are presented in a disablement list. The yellow Disablements

indicator is lit on the control panel when at least one disablement is activated in
the system and remains lit until all disablements are reconnected.

To perform a disablement you must enter access level 2B or higher.

DANGER!
When a fire detector or zone is disabled, the Fire detection system will not be able
to detect any occurring fire in that area. It is therefore important that disablements
are minimized in terms of quantity of disabled units and duration of time.

5.6.2 Available Disablements

There are four different types of disablements available.

Permanent disablement
The device is permanently disabled until it is manually enabled.

NOTE!

5100332-02B02 27
5 Operations User Guide

It is possible to limit the disablement time by defining a maximum disablement

time in the configuration program.

Timer disablement
Disablement is instantaneous and lasts for the time period entered (hh:mm).
Maximum disablement time is 23 hours 59 minutes. Maximum disablement time
can be limited depending on rules and regulations.

Clock disablement
Enter a reconnection time. Disablement is instantaneous and the reconnection will
take place next time the entered time occurs. The maximum disablement time is 23
hours 59 minutes.

Take time under consideration on ships going through different time zones (if the
system time is not synchronized with the ship's central time).

Periodic disablement
A disablement for a certain time period during certain days of the week. Example:
Disable zone 1 each Tuesday and Friday between 7.00 - 17.00.

Take time under consideration if the system is travelling through different time
zones (if the system time is not synchronized with a central time).

5.6.3 Acknowledgement of a New Disablement

Once a new disablement is correctly entered, an acknowledgement is presented on
the control panel. The Disablements button indicates with steady yellow light, use
it to activate the Disablements list.

The new disablement is also added in the disablements list under: Menu » 3
Disablements » 2 Disablement list

5.6.4 Disabling Zones

(Access level 2B or higher)

Disabling a Conventional Zone

1 Select Menu » 3 Disablements » 1 New disablement » 1 Zones

2 Choose Zone (Zone number)
3 Choose disablement type (Permanent, Timer, Clock or Periodic)
4 Enter time (if Timer, Clock or Periodic was chosen in the previous step)

5.6.5 Disabling Alarm Devices

(Access level 2B or higher)

Examples of alarm devices are bells, buzzers and flash lights.

28 5100332-02B02
User Guide 5 Operations

Disablements of alarm devices:

1 Select Menu » 3 Disablements » 1 New Disablement » 4 Alarm Device

(Bells etc.)

5.6.6 Old Disablements

Use this menu to reactivate previously performed disablements.

NOTE!
Only permanent disablements can be reactivated.

1 Select Menu » 3 Disablements » 4 Old Disablements

2 Mark the appropriate old disablement in the list and and press “0” to
reactivate the disablement (again).

5.6.7 Alarm Delay

An alarm delay function will delay the activation of alarm devices in case of a fire
alarm. The delay time is programmable and as default normally set to two minutes.

The alarm delay function (Access level 2B or higher) may be enabled/disabled:

1 Select Menu » 3 Disablements » 1 New

Disablement » 5 Alarm Delay
2 Select type of delay (Permanent, Timer, See Available Disablements ,
Clock or Periodic) page 27 for explanation.

Set delay time (Access level 3 or higher):

1 Select Menu » 5 Settings » 5 Alarm Delay NOTE!

Times » 1 Alarm Delay Time » 1 (mute) Max allowed alarm
delay time is 2
minutes acc. to
SOLAS.

5.6.8 Disabling External Outputs

(Access level 2B or higher)

Examples of external outputs are fans or outputs controlling fire doors.

1 Select Menu » 3 Disablements » 1 New

Disablement » 3 External Controls » 1
External Controls
2 Select an output category to be disabled. All groups = all categories of
doors, ventilation, etc.
3 Press

5100332-02B02 29
5 Operations User Guide

5.6.9 Disabling an Alarm Transfer Output

(Access level 2B or higher)

Disablements of the alarm transfer (fire brigade) output:

1 Select Menu » 3 Disablements » 1 New Disablement » 3 External Controls

» 2 Alarm Transfer

5.7 Reconnecting
5.7.1 Reconnecting Disabled Items
All disablements in the system are presented in the disablement list. Any
enablement is made from this list.

1 Select Menu » 3 Disablements » 2 Disablement list

2 Choose the disablement you want to cancel.
3 Press

5.7.2 Reconnecting Periodic Disablements

Periodic disablements in the system are presented in the periodic disablement list.

Reconnecting is made from this list:

1 Select Menu » 3 Disablements » 3 Periodic Disable list

2 Choose the periodic disblement you want to cancel.
3 Press

5.7.3 Remove All Disablements

This menu removes all active disablements presented in the Disablement list.

1 Select Menu » 3 Disablements » 5 Remove

all disablements
2 Confirm with OK to remove (reset) all NOTE!
active disablements in the system. Periodic disablements
are not permanently
removed. Only the
periodic disablement's
active period is
removed.

5.8 Service Menu

(Access level 2 for basic functions, but access level 4 is needed to perform
advanced service options.)

30 5100332-02B02
User Guide 5 Operations

The Service menu is used for configuring the system in the commissioning phase,
as well as for troubleshooting and making small updates when the system is in
operation. The menu has functions for loading and saving information from/to a
suitable USB Memory.

The Service menu screen displays a list of the 8 service menu alternatives, as
shown in the figure below.

Figure 11. Service menu screen.

Please refer to the Service and Maintenance manual for detailed information about
the Service menu.

5100332-02B02 31
5 Operations User Guide

32 5100332-02B02
User Guide 6 Testing

6 Testing

6.1 About Testing

For additional information about testing, please refer to the Service and
Maintenance Manual.

6.2 Test Mode Overview

NOTE!
This section is only applicable for addressable units.

The system has a special test mode function which makes the testing easier.

When a zone is in test mode:

• External alarm devices and controls are by default not activated in case of a fire.
Hint
This functionality can be turned off.

NOTE!
The system handles fire alarms from zones not in test mode in the usual way.
The tested zone will automatically return to normal operation after two hours.

6.3 Testing a Fire-detecting Zone

1 Put the zone into test mode under: Menu »
3 Disablements » 1 New Disablement » 6
Test Mode.
2 Select a zone and confirm by pressing the The Disablements, Test, and
button. Zone/Unit indicators light to
confirm that they are in test
mode.

It is now safe to test each detector and manual call point in this fire zone during the
next two hours.

All alarms are listed under: Menu » 7 History » 1 Fire History List.

NOTE!
Use appropriate test equipment. See section Recommended Test Equipment, page
34.

5100332-02B02 33
6 Testing User Guide

6.4 Recommended Test Equipment

Table 2. List of recommended test equipment for Fire detecting systems
Product Description
Testifire Multi-stimulus Detector Tester
Salwico Solo 330 Smoke Detector Tester
Salwico SOLO 461 Heat Detector Tester
Salwico VD T-1 Heat Detector tester
Salwico IR Test lamp Flame Detector Tester
Salwico UV test lamp UV Flame detector test lamp
W8066 UV test lamp

For detailed information, please refer to the data sheets for the products.

6.5 Reset Test Mode

NOTE!
After testing is completed, return the tested zone to its normal condition.
Before exiting test mode, make sure there are no detectors or manual call points in
alarm condition.
The tested zone automatically returns to normal operation after two hours.

To reset test mode:

1 The zones in test mode are listed in the Disablement List, found under:
Menu » 3 Disablements » 2 Disablement List.
2 Choose the zone in the Disablement List and then press .

6.6 Test the Control Panel Display

With the function Test display it is possible to test:

• The display
• All indications on the control panel

1 To test the control panel display, use: Menu » 5 Settings » 4 Test display.

34 5100332-02B02
User Guide 7 Appendix

7 Appendix

7.1 Fault Code List

Listed in the table below are all fault codes, their causes, and how an operator with
knowledge of the system can solve the problem.

Table 3. Fault Codes with cause and remedy

Fault Code Cause Remedy
Explanation: Lost communication. The system has recognized a unit but lost
contact.
Wrong type of loop unit Switch to the correct loop unit
Two loop units have the same address (a Check address of the units. Rescan
secondary fault appears) the loop.
Replace the unit.
Refer to the Installation manual or
128 NO ANSWER Defect unit Service & Maintenance manual:

Locate the cable break or short

circuit.
Cable break or short circuit in a loop (a Refer to the Installation manual or
secondary fault appears) Service & Maintenance manual:

Replace the unit.

Refer to the Installation manual or
The detector has a faulty sensor element Service & Maintenance manual:
129 SENSOR FAULT

The smoke detector is exposed to strong Protect the detector from the airflow
airflow or consider repositioning the detector.
Replace the detector.
Refer to the Installation manual or
The detector has a dirty (polluted) sensor
130 DIRTY SENSOR Service & Maintenance manual:
element

Check the loop configuration or

reconfigure the system
Fewer loop units found than configured.
Loop units not correctly installed or Address the unit correctly.
addressed. Refer to the Installation manual or
Service & Maintenance manual:
TOO FEW LOOP UNITS
131
FOUND
Check address (possible double
address). Otherwise replace the unit.
Missing answer from a unit Refer to the Installation manual or
Service & Maintenance manual:

5100332-02B02 35
7 Appendix User Guide

Fault Code Cause Remedy

Check the specification or reconfigure
the system.
More loop units found than configured Refer to the Installation manual or
Service & Maintenance manual:
TOO MANY LOOP
132
UNITS FOUND
Address the unit correctly.
Refer to the Installation manual or
Loop units not correctly installed
Service & Maintenance manual:

Check that the cable between input

133 IN1 CABLE BREAK There is a cable break on input 1
and end of line resistor is complete
Check that the cable between input
134 IN2 CABLE BREAK There is a cable break on input 2
and end of line resistor is complete
External 24V power source missing or Check the local power supply unit and
135 EXT 24V FAIL
the local power supply unit is defective consider replacing
136 FEEDBACK FAULT External load is missing Check the cable and the external load
A supervised unit (for example, a door
137 POSITION FAULT Check for obstructions
or damper) is in the wrong position
Locate the short circuit.
Refer to the Installation manual or
138 LOOP SHORT CIRCUIT A short circuit in the detector loop cable
Service & Maintenance manual:

Locate the short circuit.

LOOP A SHORT Short circuit on the A-side of a detector Refer to the Installation manual or
139
CIRCUIT loop Service & Maintenance manual:

Locate the short circuit.

LOOP B SHORT Short circuit on the B-side of a detector Refer to the Installation manual or
140
CIRCUIT loop Service & Maintenance manual:

Locate the cable break.

CABLE BREAK A cable break on the positive conductor Refer to the Installation manual or
141
POSITIVE has been detected Service & Maintenance manual:

Locate the cable break.

CABLE BREAK A cable break on the negative conductor Refer to the Installation manual or
142
NEGATIVE has been detected Service & Maintenance manual:

36 5100332-02B02
User Guide 7 Appendix

Fault Code Cause Remedy

Explanation: The communication with a unit is deficient
Check the loop unit addresses.
Refer to the Installation manual or
Two units have the same address Service & Maintenance manual:

COMMUNICATION Replace the unit.

143
ERROR Refer to the Installation manual or
Faulty loop unit Service & Maintenance manual:

Locate interference source.

Interference from external source If not possible to solve the problem,
contact an authorized service office
The type of unit found in the loop is
LOOP UNIT TYPE Accept the unit found or replace to
144 different from the original type
CHANGED original type
configured
Explanation: The type of unit found is not recognized by the system
UNKNOWN TYPE OF Faulty unit Replace the unit
145
LOOP UNIT FOUND Wrong type of detector has been Install the correct type and restart the
installed loop
The timer has been activated for too
146 TIMER STUCK Reset the timer to zero
long
Change one of the addresses.
Rescan or restart the loop.
Two units with the same address on a
148 DOUBLE ADDRESS Refer to the Installation manual or
loop has been found
Service & Maintenance manual:

Locate the short circuit and restore

149 SHORT CIRCUIT Short circuit detected
operation
150 VALVE CLOSED The valve is closed Open the valve
Verify if unit address is correct.
CONFIGURED NOT
151 Unit is configured but not found Verify there is power to the module.
PRESENT
Contact an authorized service office.
Verify if unit address is correct.
PRESENT NOT
152 Unit present but not configured Verify there is power to the module.
CONFIGURED
Contact an authorized service office.
Check if there are too many units
connected to the loop.
HIGH CURRENT ON The high current has exceeded
153 Refer to the Installation manual or
LOOP acceptable levels
Service & Maintenance manual:

Locate the earth fault.

EARTH FAULT Refer to the Installation manual or
155 Earth fault on the positive conductor
POSITIVE Service & Maintenance manual:

Locate the earth fault.

EARTH FAULT Refer to the Installation manual or
156 Earth fault on the negative conductor
NEGATIVE Service & Maintenance manual:

5100332-02B02 37
7 Appendix User Guide

Fault Code Cause Remedy

157 FUSE FAULT A blown fuse Replace the fuse
BATTERY CABLE FUSE A battery fuse has blown or a cable to
158 Replace fuse or restore the cable
FAULT the battery is broken
159 CABLE BREAK A cable break has been detected Restore the cable
160 CABLE OVERLOAD Too high current on the output Check external loads
EMERGENCY POWER
162 Emergency power is lost Check the emergency power supply
FAULT
Charge the battery. If the fault
remains, replace the battery.
163 BATTERY FAULT Low battery voltage detected Refer to the Service & Maintenance
manual:

The battery charger is unable to charge

164 BATTERY CHARGER Replace the battery charger
the battery
165 EXTERNAL FAULT External equipment is indicating a fault Check the external equipment
EARTH DETECTION The module is unable to detect earth
166 Contact an authorized service office
FAULT fault
167 CHECKSUM EEP Incorrect EPROM checksum Contact an authorized service office
If restarts happen repeatedly, contact
168 RESTARTED A module has restarted
an authorized service office
There is too high external load on a
170 EXTERNAL LOAD Check the load and reduce if possible
conventional zone
EXTERNAL POWER Unexpected voltage detected in a
171 Locate and remove the source
SOURCE conventional zone
Low voltage on the primary 28VDC
LOW POWER SUPPLY
172 power supply to the internal system Contact an authorized service office
PSU 1
modules
Low voltage on the secondary 28VDC
LOW POWER SUPPLY
173 power supply to the internal system Contact an authorized service office
PSU 2
modules
LOW INTERNAL Too low voltage on the 3.3V/5V feeding
174 Replace the module
POWER to the internal circuit boards
LOW POWER SUPPLY Too low incoming 24VDC supply to the
175 Contact an authorized service office
OPERATING internal circuit boards
SYSTEM The configuration file is corrupt
176 CONFIGURATION An error has occurred during Contact an authorized service office
FAULT downloading of the configuration file
External equipment indicates low Check the pressure on the supervised
177 LOW PRESSURE
pressure unit
Check cables to actuator 1. If the
178 ACTUATOR 1 Missing feedback from actuator 1
cables are OK, change the actuator.
Check cables to actuator 2. If the
179 ACTUATOR 2 Missing feedback from actuator 2
cables are OK, change the actuator.
180 MAINS POWER The main power supply is lost Check the main power supply
181 INTERNAL FAULT Internal system fault Contact an authorized service office
182 EXTERNAL FIRE Contact an authorized service office

38 5100332-02B02
User Guide 7 Appendix

Fault Code Cause Remedy

Fault code generated when a module
NO ANSWER CH 1
183 stops answering on channel 1 on the Contact an authorized service office
BACKBONE
Backbone Bus
Fault code generated when a module
NO ANSWER CH 2
184 stops answering on channel 2 on the Contact an authorized service office
BACKBONE
Backbone Bus
WRONG TYPE OF The type of loop unit found is different Change the loop unit and re-scan the
209
LOOP UNIT FOUND from the type configured loop
CAUSE/EFFECT
210 Fault detected in the configuration Contact an authorized service office
ERROR
SYNCHRONISATION The synchronisation signal in the
212 Contact an authorized service office
SIGNAL backbone is corrupt
The configuration file’s in the system Synchronise the configuration files
are not the same everywhere between all panels
CONFIG NOT
213 Central X Module Y settings in
SYNCHRONIZED
configuration file compared to Check configuration and DIP-settings.
DIP-settings are not OK.
The PSU charges with a current that
POWER SUPPLY LIMIT Check the number of modules
214 exeeds the maximum allowed current for
EXCEEDED configured or check the external load
a charger module
CHARGING CURRENT The battery is charged with more than
215 Change the battery externally
EXCEEDED the allowed charging current
The firmware in a module does not
INCOMPATIBLE comply with the modules hardware
216 Contact an authorized service office
FIRMWARE version. (Fault code generated by the
faulty module.)
The voltage from PSU 1 is too high.
217 HIGH VOLTAGE PSU 1 (Fault code generated by the Charger M Adjust the voltage from the PSU 1
modules.)
The voltage from PSU 2 is too high.
218 HIGH VOLTAGE PSU 2 (Fault code generated by the Charger M Adjust the voltage from the PSU 2
modules.)
The fuse protecting the PSU 1 voltage
219 FUSE FAULT PSU 1 input is broken. (Fault code generated by Contact an authorized service office
the Charger M modules.)
The fuse protecting the PSU 2 voltage
220 FUSE FAULT PSU 2 input is broken. (Fault code generated by Contact an authorized service office
the Charger M modules.)
PSU 1 is found but not configured in the
PSU1 PRESENT NOT
221 configuration file. (Fault code generated Check the configuration file
CONFIGURED
by the Charger M modules.)
PSU 2 is found but not configured in the
PSU2 PRESENT NOT
222 configuration file. (Fault code generated Check the configuration file
CONFIGURED
by the Charger M modules.)
The voltage level from the Charger M is
INTERNAL VOLTAGE
223 too low. (Fault code generated by the Contact an authorized service office
LOW
Charger M modules.)
The voltage level from the Charger M is
INTERNAL VOLTAGE
224 too high. (Fault code generated by the Contact an authorized service office
HIGH
Charger M modules.)

5100332-02B02 39
7 Appendix User Guide

Fault Code Cause Remedy

The XFIRE signal in the backbone is
225 XFIRE SIGNAL Contact an authorized service office
corrupt
No traffic is detected on the Primary
226 PRIMARY SYSTEM BUS Contact an authorized service office
System Bus
SECONDARY SYSTEM No traffic is detected on the Secondary
227 Contact an authorized service office
BUS System Bus
NO ANSWER SYSTEM The module has stopped answering on
228 Replace the module
BUS the system bus
The battery or Charger M is too hot.
229 OVERHEATED (Fault code generated by the Charger M Contact an authorized service office
module.)
Too low voltage detected on the
LOW VOLTAGE CH A Backbone Bus Power Supply, channel
230 Contact an authorized service office
BACKBONE A. (Fault code generated by the Charger
M modules.)
Too low voltage detected on the
LOW VOLTAGE CH B Backbone Bus Power Supply, channel B.
231 Contact an authorized service office
BACKBONE (Fault code generated by the Charger M
modules.)
232 CORRUPT FIRMWARE Contact an authorized service office
A relay is broken or in a state that
233 RELAY OUTPUT damages the relay. (The voltage over the Replace the module
relay coil is too high.)
WRONG TYPE OF The type of module found is different Change the module or the system
236
MODULE FOUND from the type configured configuration
Generated by a Control module which
First step: Replace the SD card.
237 HISTORY detected that it has an SD memory card
Contact an authorized service office.
but fail to write history log to it.
Generated by the Loop M X when the
First step: Check the power supply to
fan in an aspiration detector don’t rotate.
238 FLOW FAULT the aspiration detector.
NOTE: Critical error, can cause the
Contact an authorized service office.
detector does not alarm.
Generated by modules that have
GA-defined function and the voltage on
First step: Check that Charger M puts
the bus for the GA (General Alarm) is
239 GA ERROR out a monitoring voltage on the BBI.
too low (BBI).
Contact an authorized service office.
NOTE: Critical error, can cause the GA
stops working.
255 ILLEGAL Internal system error Contact an authorized service office

7.2 Definitions of Terms

Alarm Condition The state of the system when a fire or gas alarm is detected.
When activated the activation of Alarm Devices will be delayed for a preset time
Alarm Delay
(normally 2 minutes).
Device that is activated in case of fire, for example audible and optical alarms like
Alarm Device
bells, sirens and flashlights.
A supervised output for signalling that a fire has occurred. The Alarm Transfer Output
Alarm Transfer Output
is usually used in onshore systems for alerting the Fire Brigade.

40 5100332-02B02
User Guide 7 Appendix

The main bus outside a Central cabinet used for communication between Modules and
Backbone Bus External
stretched central parts. It consists of two redundant RS485 channels, two 24 VDC
(BBE)
power lines and the Basic Backup (BBU) signal and Synchronisation Signal (SYNC).
The main bus inside a Central Cabinet used for communication between Modules. It
Backbone Bus Internal (BBI) consists of two redundant RS-485 channels, two 24 VDC power lines and the Basic
Backup (BBU) signal and Synchronisation Signal (SYNC).
A Backbone Bus may be split in several Segments. Power feeding can be separate for
Backbone Segment each segment by using one Charger M per segment. Communication can be isolated
between segments by using Isolator Modules.
A signal in the Backbone Bus that is used for transmitting the Central's alarm status.
Basic Backup Signal (BBU) The signal is only used when a module in Managed mode loses communication with
its Controller Module.
The Cause/Effect program defines how the inputs and outputs of the system should
Cause/Effect
react.
An umbrella name for all the Modules and Devices that can be connected together, e.g.
CCP Platform
“the Control M 4.3 Module is a member of the CCP Platform”.
A Central is a complete system that can operate autonomously; monitor its detectors
and inputs, activate its outputs and display its faults and alarms. If connected to other
Central centrals, it exchanges information with the other centrals via the System Bus, thus
allowing all centrals to act as one System.
Each central can only have one Backbone Bus.
Central Cabinet Enclosure to contain a complete or part of a central.
Central Cabinet including basic functionality of Fire Detection System such as:
Compact Central Control Panel, Power supply, Battery backup, Basic I/Os and at least one analogue
addressable loop. The Cabinet supplies limited expansion possibilities.
The Control M 4.3, the Control M 2.2 and the Control M X can all act as Controller
Control Module
Modules, i.e. be in Controller Mode.
The Control M 4.3 and Control M 2.2 can act as a Control Panel, i.e. they have an
Control Panel
HMI and the rights to manipulate and supervise the System.
Control Modules can run in Controller Mode, i.e. being Master or Hot Standby Master
within a central. Control Modules can also be in managed mode, that is being a module
Controller Mode
that is managed by the master. All other modules are always running in managed
mode.
A Control Module that is in Controller Mode (master or hot standby) in a Central or
Controller Module
System.
DCS Distributed Central System (see also Stretched Central).
Detector A device capable of detecting fire or gas alarms.
Disablement of devices such as a Zones or Detectors. Alarms from disabled devices
Disablement
will be inhibited.
Emergency Shut Down System, embedded system taking care of safety procedures in
ESD System
case of emergency, for example shut down of fire doors, ventilation etc.
An additional (RS485) bus used inside a central for intra-central communication. The
Extension Bus is typically used for connecting Repeater Modules (that does not require
Extension Bus
redundant communication and power) and should not be confused with the Backbone
Bus.
Communication to external entities is called external communication, using for
External Communication
example MODBUS, NMEA or TCMS protocols.
External Control Outputs used to control external equipment, for example fire doors.
Fault Condition The state of the system when a fault is detected.

5100332-02B02 41
7 Appendix User Guide

Automatically generated signal according to a pre-defined pattern (e.g. 7 short 1 long

GA-auto
signal) for alarm devices or the PA system.
GA-Morse Signal pattern generated manually via the GA button.
GA General alarm, common activation of alarm devices and activation of the PA system.
Controller Modules in Hot Standby Mode can take over the responsibilities of the
Hot Standby Mode
Controller Module managing a Central.
An Input/Output type providing a different function depending on the configuration of
the system. The programmable functions are:
• General Input
I/O 70 • Fault Input
• Conventional Fire Alarm Zone
• Output (24 VDC/70 mA)

An Input/Output type providing a different function depending on the configuration of

the system. The programmable functions are:
• General Input
I/O 700
• Fault Input
• Output (24 VDC/700 mA)

A module with inputs and/or outputs. I/O modules always run in Managed Mode, that
I/O Module
is they must be managed by a Controller Module.
I/O Pin or I/O Signal An I/O Pin or an I/O Signal is a logical signal, compare to terminal.
Inter-central Communication Communication between centrals is called inter-central communication.
A communication channel used to interface the systems with external devices.
Interface Channel
Interface channels can be configured to communicate on different protocols.
Communication within a central is called intra-central communication. This
Intra-central Communication
communication is between modules.
A common name for the cable, loop devices and other equipment connected to a loop
Loop
module.
Fire Detectors, Gas Detectors, Manual Call Points and other devices that can be
Loop Device
connected to the Loop.
Loop Module A Module supplying power and is in charge of communication to the loop devices.
The opposite of Controller Mode. All modules that are managed by a Controller
Managed Mode
Module are in Managed Mode.
MCS Multi Central System. A System consisting of more then one Central.
MFZ Main Fire Zone.
Modules in the System can take on different roles. Connected to the Backbone Bus
they can be in:
• Central Controller Mode (Master or Hot Standby)
• Central Managed Mode
Mode of operation
Modules connected to the System Bus can be in:
• System Controller Mode (Master or Hot Standby)
• System Managed Mode

A module that is a part of the Platform, that is can be used to build Centrals. Modules
Module within the platform generally supply a Backbone Bus interface. Controller Modules
also have a System Bus Interface.

42 5100332-02B02
User Guide 7 Appendix

Module Address Module Addresses are set via DIP switches on the Modules.
Mute Acknowledge and silence the local buzzer and in some cases the alarm devices.
PA Public Addressing.
Power Output Output providing power supply, normally used to power external devices.
A condition preceding the Alarm Condition to give early warning for potentially
Pre-Alarm Condition
dangerous situations like a smouldering fire.
Programmable Output Output which signal behaviour is configurable via the Configuration Program.
PSU Power Supply Unit.
Refers to the quality or state of being redundant, that is exceeding what is necessary or
Redundancy normal. In the System the term is used to describe backup functionality like in Hot
Standby Controller Modules.
Electrically operated switch output, normally providing C/NO/NC contacts for
Relay
connection of signal receiver.
The main attribute for Repeater Panels is that they can show information but not affect
Repeater Panel
the Central (or System) they belong to. The Repeater M 4.3 is a Repeater Panel.
Modules enter 'safe state' when they detect system faults. Modules in Safe State put
Safe State their I/O in a predefined state and stop all communication in order to avoid disturbing
system integrity.
SCS Single Central System.
Salwico Safety Management interactive graphics, a PC-based software package
SMig system
providing graphical presentation and control of the System.
A central that is physically distributed to two or more physical locations. One location
Stretched central (DCS) may or may not supply power to another location (segmented) and two locations may
or may not have isolated communication lines.
A signal in the Backbone Bus that is used for transmitting synchronization signal used
Synchronization Signal
by system Modules to synchronize there behaviour.
System A System consists of one or more Centrals.
The communication bus used for connecting multi-central systems. The System Bus is
used for inter-central communication but can also be used for external communication.
System Bus
If inter-central communication redundancy is required, the system bus will consist of a
primary and a secondary System Bus.
Terminal A Terminal is a physical point of connection, compare I/O pin.
Detectors put in the Test Condition (or Test Mode) are inhibited from generating the
Test Condition Alarm Condition but the alarms are displayed on the Control Panels to prove that the
tested Detectors are operational.
Universal Serial Bus, a communications bus that may be used to connect flash
USB
memories, keyboards, mice or other devices.
The state of the system when a warning is detected. Warnings are not as serious as
Warning Condition faults and only of informative nature, for example that a Gas Detector is in need of
calibration.
Zone A group of detectors located in a geographical area.

5100332-02B02 43
7 Appendix User Guide

44 5100332-02B02
User Guide 8 Quick Guide for Control Panel M 4.3

8 Quick Guide for Control Panel M 4.3

5100332-02B02 45
8 Quick Guide for Control Panel M 4.3 User Guide

46 5100332-02B02
 Index

Index
A Fire alarms, Menu alternatives............................... 12
About testing.......................................................... 33 Fire detection system, Access levels...................... 23
Access levels, Custom specific restrictions ........... 23 Fire detection system, System description............. 5
Access levels, Description of................................. 23 Fire alarm, Information displayed in the Control
Alarm delay............................................................ 29 Panel....................................................................... 24
Alarm delay off indicator, Control Panel M 4.3 .... 8 Fire alarm, Mute..................................................... 25
Alarm device indicator, Control Panel M 4.3 ........ 8 Fire alarm, Reset .................................................... 25
Arrow keys, Control Panel M 4.3 .......................... 10 Fire history list ....................................................... 33
Arrow keys, Repeater M 4.3 .................................. 21 Fire-Fault-Dis. button, Repeater M 4.3.................. 21

C H
Clock disablement.................................................. 28 History, Explanation of menu alternatives............. 20
Control Panel M 4.3, Description of numerical History, Menu alternatives ..................................... 15
keypad .................................................................... 11
Control panel display, Testing................................ 34 L
Control Panel M 4.3, Description of operational Lamp test buttons, Repeater M 4.3 ........................ 21
controls................................................................... 9 Local Mute button, Repeater M 4.3 ....................... 21
Control Panel M 4.3, Description of system Login, Access codes............................................... 24
indicators................................................................ 8
Custom indicators, Control Panel M 4.3................ 8
M
Maintenance, Explanation of menu alternatives.... 20
D Maintenance, Menu alternatives ............................ 15
Day mode button, Control Panel M 4.3 ................. 11 Menu alternatives, Choosing ................................. 12
Day mode button, Repeater M 4.3 ......................... 21 Menu alternatives, Explanation of ......................... 15
Disablement list ..................................................... 34 Menu Alternatives, Menu tree ............................... 12
Disablement list ..................................................... 28 Menu button, Control Panel M 4.3 ........................ 10
Disablement, Acknowledgement ........................... 28 Multiple alarms button, Control Panel M 4.3 ........ 10
Disablements button, Control Panel M 4.3............ 9 Mute button, Fault alarm........................................ 26
Disablements, Explanation of menu alternatives... 16 Mute button, Fire alarm ......................................... 25
Disablements, Menu alternatives ........................... 13 Mute button, Control Panel M 4.3 ......................... 11
Disabling a conventional zone ............................... 28
Disabling alarm devices......................................... 29
Disabling alarm transfer output ............................. 30
N
Disabling external outputs ..................................... 29 Night mode button, Control Panel M 4.3............... 11
Night mode button, Repeater M 4.3....................... 21

E
Enter button, Control Panel M 4.3 ......................... 11
O
Erase button, Control Panel M 4.3......................... 11 OK button, Control Panel M 4.3............................ 10
Escape button, Control Panel M 4.3 ...................... 10
P
F Periodic disablement.............................................. 28
Fault alarm, Information displayed in the Control Permanent disablement .......................................... 27
Panel....................................................................... 26 Power indicator, Control Panel M 4.3.................... 8
Fault alarm, Mute................................................... 26 Power indicator, Repeater M 4.3 ........................... 21
Fault alarm, Reset from the Fault list..................... 26 Pre-Alarm button, Control Panel M 4.3................. 9
Fault alarms, Explanation of menu alternatives..... 16
Fault alarms, Menu alternatives............................. 12 R
Fault alarm, Reset .................................................. 26 Reconnecting disabled items.................................. 30
Fault alarm, Reset all faults ................................... 27 Reconnecting periodic disablements...................... 30
Fault button, Control Panel M 4.3 ......................... 9 Remove all disablements ....................................... 30
Fire alarm button, Control Panel M 4.3 ................. 9 Repeater M 4.3, Description of keys and
Fire alarm, Reset several alarms ............................ 25 indicators................................................................ 21
Fire alarm, From conventional zones..................... 25 Reset button, Fault alarm ....................................... 26
Fire alarms, Explanation of menu alternatives ...... 16 Reset button, Fire alarm......................................... 25

5100332-02B02 47
Index

Reset test mode ...................................................... 34

Reset button, Control Panel M 4.3......................... 10

S
Service, Explanation of menu alternatives............. 18
Service, Menu alternatives..................................... 14
Settings, Explanation of menu alternatives............ 18
Settings, Menu alternatives.................................... 14
Shortcuts button, Control Panel M 4.3................... 9
Status button, Control Panel M 4.3........................ 10
System fault indicator, Control Panel M 4.3.......... 8

T
Test Equipment ...................................................... 0
Test mode overview ............................................... 33
Test indicator, Control Panel M 4.3 ....................... 8
Test the control panel display ................................ 34
Testing a fire-detecting zone .................................. 33
Timer disablement.................................................. 28

U
USB connection, Control Panel M 4.3................... 8

W
Warning indicator, Control Panel M 4.3 ................ 8

Z
Zone indicator, Control Panel M 4.3...................... 8
Zone, Test mode..................................................... 33

48 5100332-02B02
Global Service and Support

Own companies
Sales- and service representatives

Consilium is constantly increasing and improving its global sales and service
organisation in order to provide our customers with the most competent
service and support. Today Consilium has established own companies in
16 countries plus sales and service representatives in more than 50 countries.
You will find updated contact information on our web-site www.consilium.se.

www.consilium.se
 Salwico Cargo
Conventional Fire Detection
System
Installation Manual
Consilium Marine & Safety AB
Fire & Gas Marine Division
Phone: +46 31 710 77 00
Fax: +46 31 710 78 00
E-mail: Service: [email protected]
Spares: [email protected]

Consilium Marine & Safety AB

Navigation Division
Phone: +46 8 563 05 100
Fax: +46 8 563 05 199
E-mail: Service, APT: [email protected]
Spares: [email protected]

Consilium Marine & Safety AB

Transport Division
Phone: +46 31 710 77 00
Fax: +46 31 710 78 00
E-mail: Service: [email protected]
Spares: [email protected]

The contents of this document are subject to revision without notice

due to continued progress in methodology, design and manufacturing.
Consilium assumes no legal responsibility for any error or damage
resulting from the usage of this document.

January 2012
Document no. 5100333-02B02
Part no. Part no: 5100333

© 2009-2012, Consilium Marine & Safety AB

 Table of contents

1 Introduction ...................................................................................... 1
1.1 About this Manual ........................................................................... 1
1.2 Approvals .......................................................................................... 2

2 Symbols Used in the Manual ........................................................... 3

3 General Description ......................................................................... 5

3.1 System Description ........................................................................... 5
3.2 System Block Diagram ..................................................................... 5
3.3 System Data ...................................................................................... 6

4 Installation ....................................................................................... 7
4.1 Prerequisites for Installation ........................................................... 7
4.2 Mechanical Installation ................................................................... 7
4.2.1 Installation Order ........................................................................... 7
4.2.2 Control Panels ................................................................................ 7
4.2.3 Loop Units ..................................................................................... 7
4.2.4 Mounting of Modules on a DIN rail .............................................. 7

4.3 Electrical Installation ...................................................................... 8

4.3.1 Cable Requirements ....................................................................... 8
4.3.2 Connection to Zone Module, type I/O M 70 .................................. 9
4.3.3 Test the Cable ................................................................................. 9
4.3.4 Setting the Address on Repeater M 4.3 ......................................... 10
4.3.5 Electrical Installation, Central Equipment ..................................... 10

5 Verification ....................................................................................... 13
5.1 Prerequisites for Verification ........................................................... 13
5.2 Loops ................................................................................................. 13
5.2.1 Verification of Loops ..................................................................... 13
5.2.2 Testing of System Parts .................................................................. 14

5.3 Trouble Shooting .............................................................................. 16

5.3.1 Earth Fault ...................................................................................... 16
5.3.2 Muting Faults ................................................................................. 16
5.3.3 Reset Faults .................................................................................... 16
5.3.4 Upgrade Service Pack and Firmware ............................................. 16

6 Commissioning Requirements ......................................................... 19

6.1 Prerequisite ....................................................................................... 19
6.2 Part A: Loop Configuration ............................................................ 19
6.3 Part B: Loop Status .......................................................................... 19
6.4 Part C: Central Status ...................................................................... 19
Table of contents

6.5 Summary .......................................................................................... 20

7 Fire Detection Installation Guidelines ............................................ 21

7.1 Loop Units Installation Guidelines ................................................. 21
7.1.1 General Comments when Installing Fire Detectors ....................... 21
7.1.2 Smoke Detectors ............................................................................ 21
7.1.3 Heat Detectors ................................................................................ 22
7.1.4 Flame Detectors ............................................................................. 22
7.1.5 IS Smoke Detector for EX Areas ................................................... 23
7.1.6 Conventional High Temperature Heat Detectors ........................... 23
7.1.7 Cold Room Heat Detectors ............................................................ 24
7.1.8 Manual Call Points ......................................................................... 24
7.1.9 Bells ............................................................................................... 24
7.1.10 Electrical Siren ............................................................................... 24
7.1.11 Door Holder Magnet 65kp (650N) ................................................ 24
7.1.12 Door Holder Magnet 130kp (1300N) ............................................ 24
7.1.13 Door Release Switch ...................................................................... 24

7.2 Cabling and Electrical Installation ................................................. 25

7.2.1 Cable Types .................................................................................... 25
7.2.2 Cable Protective Tubes of Metal .................................................... 25
7.2.3 Cable Protective Tubes of Plastic .................................................. 25
7.2.4 Cabling ........................................................................................... 25
7.2.5 Cable Inlets to Equipment .............................................................. 26
7.2.6 Fixing of Cables ............................................................................. 26
7.2.7 Markings ........................................................................................ 27
7.2.8 Cable Ends ..................................................................................... 27
7.2.9 Protective Earthings ....................................................................... 27
7.2.10 Location of Electrical Equipment .................................................. 28

8 Appendix ........................................................................................... 29
8.1 EN54 Functions ............................................................................... 29
8.2 Address List and Test Report ........................................................... 30
8.3 Central Unit Terminal & Cabling Layout ....................................... 31
8.4 RS485 Termination .......................................................................... 33
8.4.1 General Recommendations for Installation of RS485 ................... 33
8.4.2 Application Examples for Installation of RS485 ........................... 33

8.5 Fault Code List ................................................................................. 36

8.6 Definitions of Terms ......................................................................... 41

Index ................................................................................................. 47
Installation Manual 1 Introduction

1 Introduction

1.1 About this Manual

This manual is intended for personnel installing a fire detection system.

NOTE!
This guide is valid for Control panel software versions beginning with version
1.0.0.

Chapter General Description gives an overview of the system.

Chapter Installation describes the complete electrical installation process of the

loop units. The installation engineer does not need to have any previous knowledge
of this particular system to be able to perform an installation.

Chapter Verification describes how to test the installed system. After the
installation is completed, the system is verified, which must be performed by a
person with good knowledge of the various functions. This chapter also includes
verification and troubleshooting.

Chapter Commissioning Requirements describes the steps to be taken by the

installation organisation before a commissioning engineer can be sent from the
commissioning organisation.

Chapter Fire Detection Installation Guidelines gives general recommendations for

installing a fire detection system.

5100333-02B02 1
1 Introduction Installation Manual

Figure 1. Salwico Cargo Fire Detection System, an example.

1.2 Approvals

2 5100333-02B02
Installation Manual 2 Symbols Used in the Manual

2 Symbols Used in the Manual

DANGER!
Risk of serious or fatal injury to the user, and/or severe damage to the product, if
the instructions are not followed.

WARNING!
Risk of personal injury and/or damage to the product if the instructions are not
followed.

CAUTION!
Risk of minor or moderate personal injury. Risk of equipment damage, loss of data,
extra work, or unexpected results, if the instructions are not followed.

NOTE!
Note symbols alert you to important facts and conditions.

Hint
Tip symbols direct you to specific instructions, such as where to find additional
information and tell you how to perform a certain operation in an easier way.

5100333-02B02 3
2 Symbols Used in the Manual Installation Manual

4 5100333-02B02
Installation Manual 3 General Description

3 General Description

3.1 System Description

This Fire detection system is a state-of-the-art fire-detection system designed to
meet marine and industrial requirements. Special care is given to ergonomics and
user-friendliness with its logical and intuitive operator panel.

3.2 System Block Diagram

The following figure shows a typical system and its connected components, see
Definitions of Terms, page 41 in the Appendix for explanation of terms and
abbreviations.

Figure 2. An example of a system block diagram.

5100333-02B02 5
3 General Description Installation Manual

3.3 System Data

Table 1. System data for the Fire detection system.
System Data Specifications
84–264 VAC /
Supply voltage
90-350 VDC
Power consumption.
Depending of system configuration.
Internal system voltage 19–30 VDC
Central panel ingress protection Depending on cabinet
Number of conventional detector sections per module, I/O M
8
70
Number of inputs/outputs per module, I/O M 700 8
A detector zone with conventional non-addressable loop units
should in any case include no more than 50 enclosed spaces.
Number of modules in one central (max 64 Loop M X) max 125
MCS Multi Central System max 30 SCS
Number of control panels in one central max 8
Number of repeaters on BackBoneBus (type Control M 4.3,
Control/Repeater M 4.3, Control M 2.2, Control M X, max 8
Repeater M 4.3)
Number of repeaters on extension bus (type Repeater M 4.3) max 14 / external bus
Number of zones in a system 1-9999
Communication parameters for the external system channel RS485, 19200 Baud, Odd
parity, 8 data bits

NOTE!
System boot-time is kept to a minimum during normal operation, but it can be
extra-long after a new installation, commissioning or major maintenance work
(depending on the configuration of the data definition file).

Hint
For detailed requirements, refer to the data sheets.

6 5100333-02B02
Installation Manual 4 Installation

4 Installation

4.1 Prerequisites for Installation

CAUTION!
The installation of the Fire detection system must be performed according to
SOLAS and FSS requirements.

The different parts of the system, the control and system modules, should first be
mechanically installed. The different loop units are thereafter electrically installed
and set up according to the definition of the loops and drawings.

The cables must be tested separately before the loops are connected to the loop
module. This eliminates any problem with the cable and electrical installation of
the loop units.

The installation is completed with the electrical installation of the the control and
system modules.

4.2 Mechanical Installation

4.2.1 Installation Order
Install the control panel and central cabinet according to their drawings. The
Control Panel M 4.3 is delivered in one of two ways - installed in the Fire detection
cabinet or as a separate unit. Separate drawings are delivered with the system.

4.2.2 Control Panels

The external control panels are delivered in cabinets (IP32) for wall or console
mounting. Separate drawings are delivered with the system. Install the panels
indoors in areas in 0–80% RH non-condensing conditions and within a temperature
range of 0ºC to 50ºC.

4.2.3 Loop Units

A loop unit can be connected to a conventional zone.

The mechanical installation of the different types of loop and zone units are
described in their respective data sheets.

4.2.4 Mounting of Modules on a DIN rail

Mount the module horizontally on a 35 mm DIN rail.

• Mount one module support on each side.

• Squeeze the whole package together and tighten the screws on the supports.

5100333-02B02 7
4 Installation Installation Manual

4.3 Electrical Installation

4.3.1 Cable Requirements
Backbone Bus External (BBE)
See figure in section System Block Diagram, page 5.

The cables connecting from the backbone bus to the control panels or stretched
central part must meet the following requirements:

Channel 1 & 2
• Min 2 x 2 x 0.3 mm2, twisted pair shielded
(RS485 + backup signal, one conductor)
NOTE!
The backup signal is only needed for one channel. (The back up signal
is optional.)
• Max allowed cable length is 700 m
• Optional: Power supply (24 VDC) 1 x 2 x 0.75 mm2
Refer to the system connection drawing

NOTE!
Channel 1 and Channel 2 should be routed separately for improved safety if both
channels are used.

Detector loops
Detector loop cables must meet the following minimum requirements. We refer to
current regulations for the rest of the specification.

Loop: Min. 2 × 0.3 mm2

Sub-loop: Min. 2 × 0.3 mm2

8 5100333-02B02
Installation Manual 4 Installation

4.3.2 Connection to Zone Module, type I/O M 70

Figure 3. Example of a detector zone with conventional non-addressable loop units.

A zone should in any case include no more than 50 enclosed spaces.

4.3.3 Test the Cable

4.3.3.1 Prerequisites for Testing the Cable
The cable should be tested for proper function after all the loop units are connected
and before the cable is connected to the central unit.

4.3.3.2 Test for Earth Failure

CAUTION!
When loop units are connected, it is not allowed to use an insulation tester with a
voltage exceeding 30 V.

Measure between the + and - pole and earth to detect an earth fault.

5100333-02B02 9
4 Installation Installation Manual

4.3.4 Setting the Address on Repeater M 4.3

Follow this instruction to set address for the Repeater M 4.3 module in the system
and set the panel functions.

1 Press both arrow keys + to open the Use the arrow keys to scroll
Enter Access Code menu. and select the digits for the
Approximate 4-5 seconds. Access Code.
Confirm with the Local Mute
button (= Next digit or
Enter).
( = Previous.)
2 Proceed to choose address and layout for For all menu alternatives use
the Repeater module: the arrow keys to scroll and
• Enter Central Address select.
Confirm with the Local Mute
• Enter Module Address
button.
• Enter Layout Follow the instructions on the
Reboot the Repeater module (it will take lower part of the screen.
the module about 20 seconds to restart).

4.3.5 Electrical Installation, Central Equipment

Terminal layout
Since most systems are designed specifically for each customer, no standard for
connecting the different modules within the system exists.

Refer to Central Unit Terminal & Cabling Layout, page 31 for more information.

For other electrical installations, such as Printer and Basic Backup Signal (BBU),
refer to the specific project drawings.

10 5100333-02B02
Installation Manual 4 Installation

Control Panel
If the Control Panel is placed outside of the Fire detection cabinet, connection to
the Central Unit is made via the external Backbone Bus channel (BBE), as shown
in the System Block Diagram, page 5. Each cable should be routed seperately
for maximum security.

5100333-02B02 11
4 Installation Installation Manual

12 5100333-02B02
Installation Manual 5 Verification

5 Verification

5.1 Prerequisites for Verification

NOTE!
The configuration of the loops must be performed by a person with good
knowledge of the system. This operator must have the authority to work in access
level 4.

The system is delivered with a complete system configuration or a test

configuration.

5.2 Loops
5.2.1 Verification of Loops
NOTE!
Once the loop cable has been tested and is free from faults, the next step is to
connect it to the central.

The verification procedure is described below:

1 Make sure that the system is connected to Refer to Installation, page

an external power supply. 7 for information on the
electrical connections.
2 Connect both the A- and B-side of one of NOTE!
the loops to the Loop M X loop module Conventional loops
(addressable loop units) or I/O M 70 zone (zones) are not double
module (conventional detectors). fed and do not have a
B-side.
3 Power up the system. For more information about
The Power LED lights and a text appears the fault codes, see Fault Code
on the display to show that the system is up List, page 36.
and running.
Wait for a few minutes to let the system
perform all system checks.
If the system detects a fault during the
start-up, a fault code is displayed in the
control panel.
4 One loop is now verified and tested. Repeat step 3 for all other
Continue with the next loop. loops.

5100333-02B02 13
5 Verification Installation Manual

5 Make a fire detector test of the complete See Testing of System Parts,
Fire detection system. page 14.
Use appropriate test equipment (smoke
detector test gas, heat detector tester) to test
each detector and loop unit. See section
Recommended Test Equipment, page 15.
Print out the “Fire alarm history list” found
under Menu » 7 History » 1 Fire History
List. This list contains the 500 latest fire
alarms, and is cleared each time the system
is restarted.
6 Use a top to bottom procedure if you have
any problem with the verification of the
loop function.
Start by solving the problems that affect the
whole loop and then continue with the
problems with each address.

5.2.2 Testing of System Parts

5.2.2.1 Prerequisites for Testing
After installation of the Fire detection system, test the different parts of the system
to assure that they function properly.

5.2.2.2 About Testing

For additional information about testing, please refer to the Service and
Maintenance Manual.

5.2.2.3 Test Mode Overview

NOTE!
This section is only applicable for addressable units.

The system has a special test mode function which makes the testing easier.

When a zone is in test mode:

• External alarm devices and controls are by default not activated in case of a fire.
Hint
This functionality can be turned off.

NOTE!
The system handles fire alarms from zones not in test mode in the usual way.
The tested zone will automatically return to normal operation after two hours.

5.2.2.4 Testing a Fire-detecting Zone

1 Put the zone into test mode under: Menu »
3 Disablements » 1 New Disablement » 6
Test Mode.

14 5100333-02B02
Installation Manual 5 Verification

2 Select a zone and confirm by pressing the The Disablements, Test, and
button. Zone/Unit indicators light to
confirm that they are in test
mode.

It is now safe to test each detector and manual call point in this fire zone during the
next two hours.

All alarms are listed under: Menu » 7 History » 1 Fire History List.

NOTE!
Use appropriate test equipment. See section Recommended Test Equipment, page
15.

5.2.2.5 Recommended Test Equipment

Table 2. List of recommended test equipment for Fire detecting systems
Product Description
Testifire Multi-stimulus Detector Tester
Salwico Solo 330 Smoke Detector Tester
Salwico SOLO 461 Heat Detector Tester
Salwico VD T-1 Heat Detector tester
Salwico IR Test lamp Flame Detector Tester
Salwico UV test lamp UV Flame detector test lamp
W8066 UV test lamp

For detailed information, please refer to the data sheets for the products.

5.2.2.6 Reset Test Mode

NOTE!
After testing is completed, return the tested zone to its normal condition.
Before exiting test mode, make sure there are no detectors or manual call points in
alarm condition.
The tested zone automatically returns to normal operation after two hours.

To reset test mode:

1 The zones in test mode are listed in the Disablement List, found under:
Menu » 3 Disablements » 2 Disablement List.
2 Choose the zone in the Disablement List and then press .

5.2.2.7 Test the Control Panel Display

With the function Test display it is possible to test:

• The display
• All indications on the control panel

1 To test the control panel display, use: Menu » 5 Settings » 4 Test display.

5100333-02B02 15
5 Verification Installation Manual

5.3 Trouble Shooting

5.3.1 Earth Fault
The control panel displays which loop or central has the earth fault.

1 Examine the faulty loop to locate the earth

fault.

If the earth fault still remains after this step, examine the cables to all other devices
connected to the Fire detection system.

5.3.2 Muting Faults

1 Simultaneously mute all the faults by
pressing the Mute button.
2 The fault indication light stops flashing and The fault is put in a fault list
glows yellow. under Menu » 1 Fault Alarms
» 1 Fault List.

5.3.3 Reset Faults

NOTE!
The cause of the problem must disappear before a fault can be reset.

The faults are reset from the Fault list under Menu » 1 Fault Alarms » 1 Fault List.

The Fault is Reset

1 The fault is reset and it disappears from the fault list.

The Fault is not Reset

1 The fault is not reset and the reason for this

is displayed.
2 Check the problem and deal with it. See Fault Code List, page
36 for more information.
3 Attempt to reset the fault.

5.3.4 Upgrade Service Pack and Firmware

This instruction describes how to upgrade a service pack and firmware in a CCP
System with firmware releases of 1.4.33 and later.

A service pack contains the software for all modules in a CCP System with the
exception of Control MX / 2.2 / 4.3 and Repeater M 4.3.

NOTE!
NOTE: Service package is included in the file “cm_firmware” and downloaded
automatically in the system when the system is updated by using the
“cm_firmware”

16 5100333-02B02
Installation Manual 5 Verification

Follow the steps below to upgrade service pack and the firmware in a CCP System:

- Upgrade Service Pack in Control M 4.3, page 17

- Upgrade Firmware, page 17

Prerequisites
• A USB Memory Stick and a CCP Service pack release

5.3.4.1 Upgrade Service Pack in Control M 4.3

NOTE!
Access Level 3 is required to upgrade firmware in the system. You may be required
to login with correct credentials during the firmware upgrade process.

1 Copy the file ‘Servicepackxxx.out’ to the

root catalogue of the USB stick.
2 Insert the USB stick into the Control M 4.3
panel.
3 Select Service Menu » Firmware » Load
service pack from USB memory.
4 Select the service pack file.
5 A warning will appear regarding upgrade
of the service pack.
Press .
6 The system will download the service pack.
7 Return to the previous menu. To upgrade firmware, follow
the instructions in Upgrade
Firmware, page 17.

5.3.4.2 Upgrade Firmware

Hint
There are two methods to update firmware in modules, manually or automatically.

Manually upgrade of firmware in selected CCP Modules

NOTE!
Access Level 4 is required to upgrade firmware in the system. You may be required
to login with correct credentials during the firmware upgrade process.

1 In the Control M 4.3, select Service Menu »

Firmware » Download Firmware to
modules.
2 Wait for the system to compare firmware
versions in the service pack with the
firmware versions in the modules found by
the system.

5100333-02B02 17
5 Verification Installation Manual

3 A list of centrals is displayed.

Select the central you want to upgrade with
firmware and press 2 to get a list modules
found in that central.
4 Select the module you want to upgrade and
press 0 to start the upgrade.
5 A warning will appear regarding upgrade
of the module.
Press .
6 The system starts the upgrade of the
module.
7 Wait until the firmware download counter
has progressed to 100% and the system
reports “Operation Succeeded”.
Return to the list of modules.
8 Repeat steps 4 and 5 for all the modules Explanation of icons:
you want to upgrade. = Invalid firmware
It is recommended to upgrade modules
= Upgrade available
marked with and .
= Firmware OK
= Service Pack or Module
missing – firmware download
not available

Automatic update of software modules

NOTE!
Access Level 4 is required to upgrade firmware in the system. You may be required
to login with correct credentials during the firmware upgrade process.

NOTE!
The system will only update the modules that have software that differs from what
is in the service package.

1 In the Control M 4.3, select Service Menu » Firmware » Start automatic

update.
2 Choose between slow or fast method and press :
• Slow update (with alarm functionality)
• Fast update (no alarm functionality)
All other communication will cease.
NOTE!
Fire-Alarm functionality will stop in Fast update.

3 All modules will be upgraded to the version stored in the local service
pack.
Wait until all modules are upgraded. The system reports for example:
5. 1.1 has 0 modules left to update of total 1. Failed 0 Operation
Succeeded.

18 5100333-02B02
Installation Manual 6 Commissioning Requirements

6 Commissioning Requirements

6.1 Prerequisite
The procedure described below is to be followed by the installation team.

If nothing else is agreed, no commissioning engineer will be sent before the steps
below are confirmed and the appropriate papers are signed and sent to your local
Consilium office or authorized representative.

6.2 Part A: Loop Configuration

Refer to Cable Requirements, page 8 for cable requirements.

6.3 Part B: Loop Status

1 All units shall be located at the proper place according to the drawings.
2 Fit detector heads, manual call points, address units, and control modules
into their bases.
3 Connect cables to loop unit terminals according to the data sheet for that
loop unit.
4 Remove all plastic covers, protective tape, or other devices preventing
detectors/loop units from being functionally tested.
CAUTION!
Do not remove dust covers from smoke detectors until all polluting
(e.g., dusty) construction work is finished and the area has been
cleaned.
5 When testing loop units, follow the testing instructions provided with the
testing device.
NOTE!
Use appropriate test equipment. See section Recommended Test
Equipment, page 15.
6 A test report must be filled in for each zone as described in Address List
and Test Report.
7 Send one copy of the signed test protocol to your local Consilium office or
authorized representative.
8 When all zones are tested and all protocols are signed, your local
Consilium office or authorized representative may be requested to come
and make the final control and adjustment of the system.

6.4 Part C: Central Status

CAUTION!
The presence of an authorised engineer is required before power is connected to
the central unit to minimise the start-up costs for the yard and/or owner during
commissioning.

5100333-02B02 19
6 Commissioning Requirements Installation Manual

• All control and indication functions must be connected to relay outputs.

Connect all outputs and inputs according to the terminal drawings.
• Connect finalized zones to the central according to the terminal drawings.

NOTE!
Deviations from the above criteria may cause time delays. These time delays will
be invoiced.

6.5 Summary
For each loop, a test report as described in Address List and Test Report, page 30
must be filled in and sent to your local Consilium office or authorized
representative before commissioning of the system starts.

20 5100333-02B02
Installation Manual 7 Fire Detection Installation Guidelines

7 Fire Detection Installation Guidelines

CAUTION!
Always refer to and act according to current local rules and regulations.

7.1 Loop Units Installation Guidelines

7.1.1 General Comments when Installing Fire Detectors
This chapter provides important information for installing protective fire detection
equipment.

• For conventional (non-addressable) detectors, an end of line resistor must be

installed in the last detector/unit base of each section. The type of resistor
depends mainly on how the fire detection system is configured.
• Make sure that smoke detectors maintain their protective dust covers until
polluting activities such as construction have been completed and the area have
been cleaned.
• Each unit requires an IP class suitable for its operational environment.
• To help maintain the correct IP class, plug any unused cable glands.
• Keep the detectors protection caps on as long as possible. The protection caps
should be removed after commissioning is completed and the system is handed
over.

NOTE!
For detailed connection and installation information, refer to the data sheet for each
unit.

7.1.2 Smoke Detectors

• If possible, install smoke detectors in the center of a supervised area or where
smoke most likely arises.
• A smoke detector covers a maximum area of 74 m2.
• To avoid unnecessary alarms, keep smoke detectors away from showers, saunas,
ovens, and toasters.
• Do not install a smoke detector behind an air duct or near ventilation inlets,
which could delay smoke from reaching the detector. The minimum distance for
placement of a smoke detector from a ventilation inlet is 0.5 m.
• Do not install a smoke detector in areas with temperature below 5°C or where
condensation is likely.
• A smoke detector shall not be installed where it may be exposed to direct air
flow > 20 m/s.
• A smoke detector’s minimum distance from a wall or a bulkhead is 0.5 m.

5100333-02B02 21
7 Fire Detection Installation Guidelines Installation Manual

Figure 4. Smoke detector locations.

• The maximum distance for a smoke detector from a wall or a bulkhead is 5.5 m.
The maximum distance between two detectors is 11 m.
• When placed in engine spaces, smoke detectors shall have 2 m extra cable slack
to enable relocation within the space.
• In cabins and in lockers, mount the detector with its LEDs facing toward the
door.

7.1.3 Heat Detectors

• Install a heat detector in an area’s center and where it can work reliably and
provide the best protection.
• A heat detector covers a maximum area of 37 m2.
• The alarm temperature of the detector shall be set least 30ºC above normal
temperature.
• Avoid placing the detector near heat-generating devices, such as ovens or
saunas, which could cause unwanted alarms.
• A heat detector’s minimum distance from a bulkhead is 0.5 m.
• A heat detector is installed a maximum distance of 4.5 m from a wall or a
bulkhead. The maximum distance between two heat detectors is 9 m.
• In cabins and in lockers, mount the detector with its LEDs facing toward the
door.

7.1.4 Flame Detectors

• Install flame detectors where flames, in the initial stage of a fire, might arise.
• Mount the detector giving it wide access to the whole area where the flames are
expected. When placing the detector, try to “see” the area as the detector might.
• Mount the detector in such a way that vibrations are avoided as much as
possible.
• Avoid shadow areas from objects in the room, by placing a second detector
facing the opposite side of the object, see Figure 5. Flame detector mounting.

22 5100333-02B02
Installation Manual 7 Fire Detection Installation Guidelines

• Mount the flame detector to give it clear access to the location of the anticipated
fire. A detector has a typical cone of vision of 100° from the central axis, see
data sheet of flame detector for more information. Place the detector beside, but
not directly above, the protected object to prevent the risk that black smoke may
block the flames. Place the detector at an angle of 45° downwards. This way the
detector will project both downward and forward and catch the least amount of
dirt. For more information about its angle of projection, refer to the flame
detector’s data sheet.

Figure 5. Flame detector mounting

• A general rule is to install the detector on a height that is twice the height of the
highest object in the supervised area, if possible.
• Avoid sources for false alarm (e.g. flares) from entering the detector’s cone of
vision.

7.1.5 IS Smoke Detector for EX Areas

• Select the detector’s location as described under section Smoke Detectors, page
21.
• Detectors are connected to the fire detection loop through an isolator unit,
which should be located in a safe area directly outside of the protected EX area.
The smoke detector should be made easily accessible for service.

7.1.6 Conventional High Temperature Heat Detectors

• Saunas generally have ceiling-installed detectors.
• Install a heat detector in an area’s center and where it can work reliably and
provide the best protection.
• A heat detector’s minimum distance from a bulkhead is 0.5 m.
• The alarm temperature of the detector should be set at least 30ºC above normal
attainable temperature.

5100333-02B02 23
7 Fire Detection Installation Guidelines Installation Manual

7.1.7 Cold Room Heat Detectors

• Install a heat detector in an area’s center and where it can work reliably and
provide the best protection.
• A heat detector’s minimum distance from a bulkhead is 0.5 m.

7.1.8 Manual Call Points

• A manual call point shall be installed at each exit at a height of 1600 mm from
deck to the centre of the call point. No part of a corridor shall be more than 20
m away from a call point. Positions where risk for impact or physical damage is
likely to occur shall be avoided.
• In special category spaces call points shall be spaced so that no part of the space
is more than 20 m away from a call point, and one shall be placed close to each
exit from such spaces.
• A test key is supplied with each call point. Save these keys for future tests.

7.1.9 Bells
• Installation height is normally 0.2 m from the ceiling and max 2.2 m from the
floor.
• After installation, make sure that the gong is free from the cables, otherwise the
sound output may be reduced.
• Should be mounted with cable entrance facing downwards.

7.1.10 Electrical Siren

• Make sure to programme the siren to the correct sound and intermittence using
the DIP switch inside the siren. More information about how to set the DIP
switch is found in the siren’s data sheet.
• Turn the volume control to max.
• Clearly label the siren with the alarm’s category (e.g., FIRE ALARM).

7.1.11 Door Holder Magnet 65kp (650N)

• Normally used for door leaves less than 1050 mm wide.

7.1.12 Door Holder Magnet 130kp (1300N)

• Normally used for door leaves more than 1050 mm wide.

7.1.13 Door Release Switch

• This switch is normally placed on both sides of each fire door. Make sure it is
not hidden behind the door leaf when the door is in open position.
• Installation height is normally 1.8 m above deck or floor level.

24 5100333-02B02
Installation Manual 7 Fire Detection Installation Guidelines

7.2 Cabling and Electrical Installation

7.2.1 Cable Types
All cables must be approved for marine installations. Refer to section Cable
Requirements, page 8.

7.2.2 Cable Protective Tubes of Metal

When installing cable protective tubes – take into account that the cable easily can
be pulled through the tube and afterwards easily be changed or removed.

When installing metal cable tubes – following must be taken into account:

• If there is more than one cable in the same tube, the cross section (counted of
mutual external diameters) may be max 40% of the inner cross section of the
tube.
• If the tube is more than 10 m long, drafting holes has to be done.
• Tubes must be installed on support so that the background may be painted.
• Tube installation must be done by welding or by tube joints. Fastening distances
are located 100 mm from the tube end and afterwards every 1.5 m.
• Bending radius must be at least 6 times the external diameter of the tube.
• The upper tube end in open decks must be sealed up, this to prevent water from
coming in.

7.2.3 Cable Protective Tubes of Plastic

Plastic tubes will be used inside the wall linings and also in the ceiling, where
attachment directly to the supporting construction is not possible.

When installing plastic cable tubes – following must be taken into account:

• Bending radius must be at least six times external diameter of the tube.
• Installation must be done onto the warm side of a thermal insulation and at least
100 mm from a hot surface, preferably below it. Piping is not allowed inside a
thermal insulation.
• The tubes are tied with galvanized wire clips. The first clip is located
approximately 100 mm from the tube end and afterwards every 1 m.

7.2.4 Cabling
When installing the cables – take into account the minimum internal bending
radius, that has nominal value of six times the external diameter of the cable.

• If two separate routes for the cables are required – all supplies and involved
control cables must be passed by separate routes according to the drawings and
cable passing list.
• Do not bundle low voltage cables together with power cables, they have to be
separated from each other.

5100333-02B02 25
7 Fire Detection Installation Guidelines Installation Manual

• When cable bundles are mounted on trays this can be done as follows:
• On the trays along the ship – the power cables on the left side (Port-side)
and the low voltage cables on the right side (Starboard-side) of the tray.
• On the trays across the ship – the power cables to the fore side and the low
voltage cables in the stern side of the tray.
• On the fore or stem bulkhead trays in vertical shaft – the power cables to the
Port-side or the Starboard-side bulkhead trays, the power cables to the fore
side and the low voltage cables to the stern side of the tray.

• In cable junctions and when exiting the cable trays bridges with fastening bolts
have to be used – low voltage cables for alarm, communication, navigational
and measuring equipment have to be installed in their own bundles.
• Each fire detector installed in engine room areas shall have two (2) meters extra
cables, this to make it possible to relocate the detector position when
performing “real” smoke tests with fans etc. running.

7.2.5 Cable Inlets to Equipment

When installing – the following must be taken into account.

• Wet spaces:
• Cables are penetrated from the bellow or from the side with diaphragm
seals.
• Let the cables enter the sealing at a right angle (or as near a right angle as
possible).

• Dry spaces:
• Free entering

No cables are to be installed below 50 mm distance from bottom or fuel oil tank,
except cables ending in these spaces.

7.2.6 Fixing of Cables

When fixing the cables – the following must be taken into account.

• When cable bundles are mounted on trays the fixing is as follow:

• Cables above a tray:
- a few small cables with a normal bundle tie
- bigger bundles with wide bundle ties
• Cables under a tray, vertical trays and tray installed in their angle side:
- plastic bundle ties can be used, however every fourth tie shall be of metal

• Outdoor cables shall be mounted with stainless steel band or bundle-ties of

steel.
• Cable fixing is to be done at every ladder rung, max 400 mm.
• Cable fixing in device penetrations/switchboards/desks etc. are to be fixed so
that possible mechanical strain do not pass over to penetrations or connection
points.

26 5100333-02B02
Installation Manual 7 Fire Detection Installation Guidelines

• When installing cables without plastic tube inside the lining, the cables are
fastened to supporting construction of the ceiling with plastic bundle-ties.

7.2.7 Markings
• Cables entering terminal boxes and equals shall be marked with identification
markings.
• The cable identification is to be done with a metal dymo-tape – on open decks
the dymo-tape must be of stainless steel.
• Cable markings are the same as the identification marks in the drawings.

7.2.8 Cable Ends

When terminating the cables – the following must be taken into account:

• The cable is passed in switchboards, decks and terminals unpeeled as near the
connection place as possible.
• Mark extra wires (not used) and do not cut them.
• Earthing wire is marked with yellow/green sleeve.
• Cable wire ends of 0.5–2.5 mm2 shall be equipped with compression-type
collar, if the contact screw presses direct wires.
• A cable eye shall be installed at the end of a conductor, connected by means of
a screw or a bolt.
• No more than two conductors shall be connected onto one side of the same
terminal.

7.2.9 Protective Earthings

• All metal casings of electrical equipment over 24 V are to be earthed to the
ships hull. When the earthing is done with cable conductors – yellow/green
conductors are to be used or last conductor wire of the cable covered along the
whole length with yellow/green hose. Yellow/green is used only for earthings.
• A separate earthing conductor is connected to the earthing point on the external
enclosure of the equipment and on the ships hull by means of a screw
connection.
• Devices shall not be earthed by means of a separate earthing conductor through
another installation (serial earthing).
• The door of a metal casing containing electrical equipment (voltage over 24 V)
must be earthed to the casings body with one earthing conductor. The earthing
fastening screw shall have a diameter of at least 6 mm with the exception of the
screws mounted by the manufacturer. The earthing screw shall not be used for
any other purpose than earthing.
• Electrical equipment is to be earthed by S-conductor (yellow/green) of supply
cable with a cross section area of 1.5–16 mm2.

Other equipment earthings - see table below.

5100333-02B02 27
7 Fire Detection Installation Guidelines Installation Manual

Table 3. Protective earthings for other equipment.

Cross section of supply
1.5 2.5 4 6 10 16 25 35 50
cable (mm2)
S-conductur (mm2)
6 6 6 6 6 10 16 25 35
(yellow/green)

7.2.10 Location of Electrical Equipment

The mounting heights are according to the table below, unless otherwise specified
in the drawings.

Table 4. Mounting heights of electrical equipment.

Interior spaces
Machinery spaces Outdoor decks
Centre (mm) From the deck From the ceiling Down edge (mm)
(mm) (mm)
Switches 1500 1100
Fire door release buttons 1800
Fire alarms bells max 2200 200 2200
Fire alarm buttons 1600 1600
Fire damper buttons 1500 2000 2200

28 5100333-02B02
Installation Manual 8 Appendix

8 Appendix

8.1 EN54 Functions

Optional functions with requirements
The following optional functions with requirements are available in the Fire
detection system:

The paragraphs in the tables below refer to EN54-2:1997/AC:1999, A1:2006.

Table 5. Optional functions.

Paragraph Function description
7.8 Output to fire alarm devices (Item C)
7.9.1 Output to fire alarm routing equipment (Item E)
Delays to outputs (Item C+E)
7.11.1-2
Note! Max allowed alarm delay time is 10 minutes acc. to EN54-2.
7.12.3 Co-incidence detection (Item C)
8.3 Fault signals from points
8.9 Fault warning routing equipment (Item J)
9.5 Disablement of addressable points
10 Test condition

Functions relating to other parts of the EN54 standard

The system includes an integrated power supply that meets all mandatory functions
of EN54-4:1997/AC:1999 and A2:2006.

Ancillary functions not required by EN54

• Earth failure
The Fire detection system has the capability to indicate earth failure
individually per fire detection loop and power supply.
• Control panel
It is possible to mount the control panel separately from the central. See the
block diagram in section System Block Diagram, page 5.

5100333-02B02 29
8 Appendix Installation Manual

8.2 Address List and Test Report

30 5100333-02B02
Installation Manual 8 Appendix

8.3 Central Unit Terminal & Cabling Layout

Description of System Modules
The Fire detection system is based on standard modules. Below is a list of some
common modules:

Control Panel M 4.3

A Control Panel with a 4.3” display that manages and supervises a system and
can act as bus master or slave.
Repeater M 4.3
A Repeater Panel with 4.3” display that can act as bus slave.
Control M 2.2
A Control Panel with a 2.2” display that manages and supervises a system and
can act as bus master or slave.
Control M X
A Control Module without display that can act as bus master or slave. It is used
for providing additional communication channels in the system.
Loop M X
A module that supplies one Addressable Loop.
I/O M 70
A Module that provides 8 I/Os of type I/O 70. Each I/O can be programmed for
use as: an input (max 70 mA), an output for buzzers, relays etc (max 70 mA) or
a conventional detector zone.
I/O M 700
A Module that provides 8 I/Os of type I/O 700. Each I/O can be programmed
for use as: an input or an output for magnets, power supply etc (max 700 mA).
Relay M 8
A Module that provides 8 potential free contacts.

Charger M
A Module that supervises and controls the power and battery functions.

Change Over M Ext

A change-over module that monitors mains and emergency power inputs.
Bus Isolator M
Is used for dividing the system backbone bus into segments. Can provide power
to Control Panel M 4.3 and Control M 2.2.
PSU M AC/DC 5A
A 5 ampere 115/230 VAC/VDC Power Supply.
PSU units can be used in pairs to supply 5+5 A.

For complete information, see the data sheet for each module.

An example of a central unit terminal layout with cabling

Since all Fire detection systems are tailored to each customer installation, no
standard exists for how the different modules are to be connected in the system.
However, in the figure below you will find an example with one module of each
type showing the connection terminals.

5100333-02B02 31
8 Appendix Installation Manual

Figure 6. An example of a central unit terminal layout with cabling.

32 5100333-02B02
Installation Manual 8 Appendix

8.4 RS485 Termination

8.4.1 General Recommendations for Installation of
RS485
General recommendations for RS485 installation:

• Twisted pair wire should be used

• Shielded cables
• Star networks are not permitted
• Termination shall be made at each end of the bus with a 120 ohm resistor
• Max 700 m cable in one communications segment
• Two-wire connection shall be used when nodes have a common ground (-)
• Three-wire connection shall be used when nodes have a different ground (-), for
example between Isolator M.

8.4.2 Application Examples for Installation of RS485

Activate the built-in terminator (120 ohm).
=
See datasheet for location of the DIP switch.
= Terminator 120 ohm

8.4.2.1 Terminating of BBE and Extensions bus

5100333-02B02 33
8 Appendix Installation Manual

8.4.2.2 Terminating of BBE example 1

34 5100333-02B02
Installation Manual 8 Appendix

8.4.2.3 Terminating of BBE example 2

8.4.2.4 Terminating of modules (BBI) mounted on single DIN rail

5100333-02B02 35
8 Appendix Installation Manual

8.4.2.5 Terminating of modules (BBI) mounted on more then one

DIN rail

8.5 Fault Code List

Listed in the table below are all fault codes, their causes, and how an operator with
knowledge of the system can solve the problem.

Table 6. Fault Codes with cause and remedy

Fault Code Cause Remedy
Explanation: Lost communication. The system has recognized a unit but lost
contact.
Wrong type of loop unit Switch to the correct loop unit
Two loop units have the same address (a Check address of the units. Rescan
secondary fault appears) the loop.
Replace the unit.
Refer to the Installation manual or
128 NO ANSWER Defect unit Service & Maintenance manual:

Locate the cable break or short

circuit.
Cable break or short circuit in a loop (a Refer to the Installation manual or
secondary fault appears) Service & Maintenance manual:

Replace the unit.

Refer to the Installation manual or
The detector has a faulty sensor element Service & Maintenance manual:
129 SENSOR FAULT

The smoke detector is exposed to strong Protect the detector from the airflow
airflow or consider repositioning the detector.

36 5100333-02B02
Installation Manual 8 Appendix

Fault Code Cause Remedy

Replace the detector.
Refer to the Installation manual or
The detector has a dirty (polluted) sensor
130 DIRTY SENSOR Service & Maintenance manual:
element

Check the loop configuration or

reconfigure the system
Fewer loop units found than configured.
Loop units not correctly installed or Address the unit correctly.
addressed. Refer to the Installation manual or
Service & Maintenance manual:
TOO FEW LOOP UNITS
131
FOUND
Check address (possible double
address). Otherwise replace the unit.
Missing answer from a unit Refer to the Installation manual or
Service & Maintenance manual:

Check the specification or reconfigure

the system.
More loop units found than configured Refer to the Installation manual or
Service & Maintenance manual:
TOO MANY LOOP
132
UNITS FOUND
Address the unit correctly.
Refer to the Installation manual or
Loop units not correctly installed
Service & Maintenance manual:

Check that the cable between input

133 IN1 CABLE BREAK There is a cable break on input 1
and end of line resistor is complete
Check that the cable between input
134 IN2 CABLE BREAK There is a cable break on input 2
and end of line resistor is complete
External 24V power source missing or Check the local power supply unit and
135 EXT 24V FAIL
the local power supply unit is defective consider replacing
136 FEEDBACK FAULT External load is missing Check the cable and the external load
A supervised unit (for example, a door
137 POSITION FAULT Check for obstructions
or damper) is in the wrong position
Locate the short circuit.
Refer to the Installation manual or
138 LOOP SHORT CIRCUIT A short circuit in the detector loop cable
Service & Maintenance manual:

Locate the short circuit.

LOOP A SHORT Short circuit on the A-side of a detector Refer to the Installation manual or
139
CIRCUIT loop Service & Maintenance manual:

Locate the short circuit.

LOOP B SHORT Short circuit on the B-side of a detector Refer to the Installation manual or
140
CIRCUIT loop Service & Maintenance manual:

Locate the cable break.

CABLE BREAK A cable break on the positive conductor Refer to the Installation manual or
141
POSITIVE has been detected Service & Maintenance manual:

5100333-02B02 37
8 Appendix Installation Manual

Fault Code Cause Remedy

Locate the cable break.
CABLE BREAK A cable break on the negative conductor Refer to the Installation manual or
142
NEGATIVE has been detected Service & Maintenance manual:

Explanation: The communication with a unit is deficient

Check the loop unit addresses.
Refer to the Installation manual or
Two units have the same address Service & Maintenance manual:

COMMUNICATION Replace the unit.

143
ERROR Refer to the Installation manual or
Faulty loop unit Service & Maintenance manual:

Locate interference source.

Interference from external source If not possible to solve the problem,
contact an authorized service office
The type of unit found in the loop is
LOOP UNIT TYPE Accept the unit found or replace to
144 different from the original type
CHANGED original type
configured
Explanation: The type of unit found is not recognized by the system
UNKNOWN TYPE OF Faulty unit Replace the unit
145
LOOP UNIT FOUND Wrong type of detector has been Install the correct type and restart the
installed loop
The timer has been activated for too
146 TIMER STUCK Reset the timer to zero
long
Change one of the addresses.
Rescan or restart the loop.
Two units with the same address on a
148 DOUBLE ADDRESS Refer to the Installation manual or
loop has been found
Service & Maintenance manual:

Locate the short circuit and restore

149 SHORT CIRCUIT Short circuit detected
operation
150 VALVE CLOSED The valve is closed Open the valve
Verify if unit address is correct.
CONFIGURED NOT
151 Unit is configured but not found Verify there is power to the module.
PRESENT
Contact an authorized service office.
Verify if unit address is correct.
PRESENT NOT
152 Unit present but not configured Verify there is power to the module.
CONFIGURED
Contact an authorized service office.
Check if there are too many units
connected to the loop.
HIGH CURRENT ON The high current has exceeded
153 Refer to the Installation manual or
LOOP acceptable levels
Service & Maintenance manual:

Locate the earth fault.

EARTH FAULT Refer to the Installation manual or
155 Earth fault on the positive conductor
POSITIVE Service & Maintenance manual:
Earth Fault

38 5100333-02B02
Installation Manual 8 Appendix

Fault Code Cause Remedy

Locate the earth fault.
EARTH FAULT Refer to the Installation manual or
156 Earth fault on the negative conductor
NEGATIVE Service & Maintenance manual:
Earth Fault
157 FUSE FAULT A blown fuse Replace the fuse
BATTERY CABLE FUSE A battery fuse has blown or a cable to
158 Replace fuse or restore the cable
FAULT the battery is broken
159 CABLE BREAK A cable break has been detected Restore the cable
160 CABLE OVERLOAD Too high current on the output Check external loads
EMERGENCY POWER
162 Emergency power is lost Check the emergency power supply
FAULT
Charge the battery. If the fault
remains, replace the battery.
163 BATTERY FAULT Low battery voltage detected Refer to the Service & Maintenance
manual:

The battery charger is unable to charge

164 BATTERY CHARGER Replace the battery charger
the battery
165 EXTERNAL FAULT External equipment is indicating a fault Check the external equipment
EARTH DETECTION The module is unable to detect earth
166 Contact an authorized service office
FAULT fault
167 CHECKSUM EEP Incorrect EPROM checksum Contact an authorized service office
If restarts happen repeatedly, contact
168 RESTARTED A module has restarted
an authorized service office
There is too high external load on a
170 EXTERNAL LOAD Check the load and reduce if possible
conventional zone
EXTERNAL POWER Unexpected voltage detected in a
171 Locate and remove the source
SOURCE conventional zone
Low voltage on the primary 28VDC
LOW POWER SUPPLY
172 power supply to the internal system Contact an authorized service office
PSU 1
modules
Low voltage on the secondary 28VDC
LOW POWER SUPPLY
173 power supply to the internal system Contact an authorized service office
PSU 2
modules
LOW INTERNAL Too low voltage on the 3.3V/5V feeding
174 Replace the module
POWER to the internal circuit boards
LOW POWER SUPPLY Too low incoming 24VDC supply to the
175 Contact an authorized service office
OPERATING internal circuit boards
SYSTEM The configuration file is corrupt
176 CONFIGURATION An error has occurred during Contact an authorized service office
FAULT downloading of the configuration file
External equipment indicates low Check the pressure on the supervised
177 LOW PRESSURE
pressure unit
Check cables to actuator 1. If the
178 ACTUATOR 1 Missing feedback from actuator 1
cables are OK, change the actuator.
Check cables to actuator 2. If the
179 ACTUATOR 2 Missing feedback from actuator 2
cables are OK, change the actuator.
180 MAINS POWER The main power supply is lost Check the main power supply

5100333-02B02 39
8 Appendix Installation Manual

Fault Code Cause Remedy

181 INTERNAL FAULT Internal system fault Contact an authorized service office
182 EXTERNAL FIRE Contact an authorized service office
Fault code generated when a module
NO ANSWER CH 1
183 stops answering on channel 1 on the Contact an authorized service office
BACKBONE
Backbone Bus
Fault code generated when a module
NO ANSWER CH 2
184 stops answering on channel 2 on the Contact an authorized service office
BACKBONE
Backbone Bus
WRONG TYPE OF The type of loop unit found is different Change the loop unit and re-scan the
209
LOOP UNIT FOUND from the type configured loop
CAUSE/EFFECT
210 Fault detected in the configuration Contact an authorized service office
ERROR
SYNCHRONISATION The synchronisation signal in the
212 Contact an authorized service office
SIGNAL backbone is corrupt
The configuration file’s in the system Synchronise the configuration files
are not the same everywhere between all panels
CONFIG NOT
213 Central X Module Y settings in
SYNCHRONIZED
configuration file compared to Check configuration and DIP-settings.
DIP-settings are not OK.
The PSU charges with a current that
POWER SUPPLY LIMIT Check the number of modules
214 exeeds the maximum allowed current for
EXCEEDED configured or check the external load
a charger module
CHARGING CURRENT The battery is charged with more than
215 Change the battery externally
EXCEEDED the allowed charging current
The firmware in a module does not
INCOMPATIBLE comply with the modules hardware
216 Contact an authorized service office
FIRMWARE version. (Fault code generated by the
faulty module.)
The voltage from PSU 1 is too high.
217 HIGH VOLTAGE PSU 1 (Fault code generated by the Charger M Adjust the voltage from the PSU 1
modules.)
The voltage from PSU 2 is too high.
218 HIGH VOLTAGE PSU 2 (Fault code generated by the Charger M Adjust the voltage from the PSU 2
modules.)
The fuse protecting the PSU 1 voltage
219 FUSE FAULT PSU 1 input is broken. (Fault code generated by Contact an authorized service office
the Charger M modules.)
The fuse protecting the PSU 2 voltage
220 FUSE FAULT PSU 2 input is broken. (Fault code generated by Contact an authorized service office
the Charger M modules.)
PSU 1 is found but not configured in the
PSU1 PRESENT NOT
221 configuration file. (Fault code generated Check the configuration file
CONFIGURED
by the Charger M modules.)
PSU 2 is found but not configured in the
PSU2 PRESENT NOT
222 configuration file. (Fault code generated Check the configuration file
CONFIGURED
by the Charger M modules.)
The voltage level from the Charger M is
INTERNAL VOLTAGE
223 too low. (Fault code generated by the Contact an authorized service office
LOW
Charger M modules.)

40 5100333-02B02
Installation Manual 8 Appendix

Fault Code Cause Remedy

The voltage level from the Charger M is
INTERNAL VOLTAGE
224 too high. (Fault code generated by the Contact an authorized service office
HIGH
Charger M modules.)
The XFIRE signal in the backbone is
225 XFIRE SIGNAL Contact an authorized service office
corrupt
No traffic is detected on the Primary
226 PRIMARY SYSTEM BUS Contact an authorized service office
System Bus
SECONDARY SYSTEM No traffic is detected on the Secondary
227 Contact an authorized service office
BUS System Bus
NO ANSWER SYSTEM The module has stopped answering on
228 Replace the module
BUS the system bus
The battery or Charger M is too hot.
229 OVERHEATED (Fault code generated by the Charger M Contact an authorized service office
module.)
Too low voltage detected on the
LOW VOLTAGE CH A Backbone Bus Power Supply, channel
230 Contact an authorized service office
BACKBONE A. (Fault code generated by the Charger
M modules.)
Too low voltage detected on the
LOW VOLTAGE CH B Backbone Bus Power Supply, channel B.
231 Contact an authorized service office
BACKBONE (Fault code generated by the Charger M
modules.)
232 CORRUPT FIRMWARE Contact an authorized service office
A relay is broken or in a state that
233 RELAY OUTPUT damages the relay. (The voltage over the Replace the module
relay coil is too high.)
WRONG TYPE OF The type of module found is different Change the module or the system
236
MODULE FOUND from the type configured configuration
Generated by a Control module which
First step: Replace the SD card.
237 HISTORY detected that it has an SD memory card
Contact an authorized service office.
but fail to write history log to it.
Generated by the Loop M X when the
First step: Check the power supply to
fan in an aspiration detector don’t rotate.
238 FLOW FAULT the aspiration detector.
NOTE: Critical error, can cause the
Contact an authorized service office.
detector does not alarm.
Generated by modules that have
GA-defined function and the voltage on
First step: Check that Charger M puts
the bus for the GA (General Alarm) is
239 GA ERROR out a monitoring voltage on the BBI.
too low (BBI).
Contact an authorized service office.
NOTE: Critical error, can cause the GA
stops working.
255 ILLEGAL Internal system error Contact an authorized service office

8.6 Definitions of Terms

Alarm Condition The state of the system when a fire or gas alarm is detected.
When activated the activation of Alarm Devices will be delayed for a preset time
Alarm Delay
(normally 2 minutes).

5100333-02B02 41
8 Appendix Installation Manual

Device that is activated in case of fire, for example audible and optical alarms like
Alarm Device
bells, sirens and flashlights.
A supervised output for signalling that a fire has occurred. The Alarm Transfer Output
Alarm Transfer Output
is usually used in onshore systems for alerting the Fire Brigade.
The main bus outside a Central cabinet used for communication between Modules and
Backbone Bus External
stretched central parts. It consists of two redundant RS485 channels, two 24 VDC
(BBE)
power lines and the Basic Backup (BBU) signal and Synchronisation Signal (SYNC).
The main bus inside a Central Cabinet used for communication between Modules. It
Backbone Bus Internal (BBI) consists of two redundant RS-485 channels, two 24 VDC power lines and the Basic
Backup (BBU) signal and Synchronisation Signal (SYNC).
A Backbone Bus may be split in several Segments. Power feeding can be separate for
Backbone Segment each segment by using one Charger M per segment. Communication can be isolated
between segments by using Isolator Modules.
A signal in the Backbone Bus that is used for transmitting the Central's alarm status.
Basic Backup Signal (BBU) The signal is only used when a module in Managed mode loses communication with
its Controller Module.
The Cause/Effect program defines how the inputs and outputs of the system should
Cause/Effect
react.
An umbrella name for all the Modules and Devices that can be connected together, e.g.
CCP Platform
“the Control M 4.3 Module is a member of the CCP Platform”.
A Central is a complete system that can operate autonomously; monitor its detectors
and inputs, activate its outputs and display its faults and alarms. If connected to other
Central centrals, it exchanges information with the other centrals via the System Bus, thus
allowing all centrals to act as one System.
Each central can only have one Backbone Bus.
Central Cabinet Enclosure to contain a complete or part of a central.
Central Cabinet including basic functionality of Fire Detection System such as:
Compact Central Control Panel, Power supply, Battery backup, Basic I/Os and at least one analogue
addressable loop. The Cabinet supplies limited expansion possibilities.
The Control M 4.3, the Control M 2.2 and the Control M X can all act as Controller
Control Module
Modules, i.e. be in Controller Mode.
The Control M 4.3 and Control M 2.2 can act as a Control Panel, i.e. they have an
Control Panel
HMI and the rights to manipulate and supervise the System.
Control Modules can run in Controller Mode, i.e. being Master or Hot Standby Master
within a central. Control Modules can also be in managed mode, that is being a module
Controller Mode
that is managed by the master. All other modules are always running in managed
mode.
A Control Module that is in Controller Mode (master or hot standby) in a Central or
Controller Module
System.
DCS Distributed Central System (see also Stretched Central).
Detector A device capable of detecting fire or gas alarms.
Disablement of devices such as a Zones or Detectors. Alarms from disabled devices
Disablement
will be inhibited.
Emergency Shut Down System, embedded system taking care of safety procedures in
ESD System
case of emergency, for example shut down of fire doors, ventilation etc.
An additional (RS485) bus used inside a central for intra-central communication. The
Extension Bus is typically used for connecting Repeater Modules (that does not require
Extension Bus
redundant communication and power) and should not be confused with the Backbone
Bus.

42 5100333-02B02
Installation Manual 8 Appendix

Communication to external entities is called external communication, using for

External Communication
example MODBUS, NMEA or TCMS protocols.
External Control Outputs used to control external equipment, for example fire doors.
Fault Condition The state of the system when a fault is detected.
Automatically generated signal according to a pre-defined pattern (e.g. 7 short 1 long
GA-auto
signal) for alarm devices or the PA system.
GA-Morse Signal pattern generated manually via the GA button.
GA General alarm, common activation of alarm devices and activation of the PA system.
Controller Modules in Hot Standby Mode can take over the responsibilities of the
Hot Standby Mode
Controller Module managing a Central.
An Input/Output type providing a different function depending on the configuration of
the system. The programmable functions are:
• General Input
I/O 70 • Fault Input
• Conventional Fire Alarm Zone
• Output (24 VDC/70 mA)

An Input/Output type providing a different function depending on the configuration of

the system. The programmable functions are:
• General Input
I/O 700
• Fault Input
• Output (24 VDC/700 mA)

A module with inputs and/or outputs. I/O modules always run in Managed Mode, that
I/O Module
is they must be managed by a Controller Module.
I/O Pin or I/O Signal An I/O Pin or an I/O Signal is a logical signal, compare to terminal.
Inter-central Communication Communication between centrals is called inter-central communication.
A communication channel used to interface the systems with external devices.
Interface Channel
Interface channels can be configured to communicate on different protocols.
Communication within a central is called intra-central communication. This
Intra-central Communication
communication is between modules.
A common name for the cable, loop devices and other equipment connected to a loop
Loop
module.
Fire Detectors, Gas Detectors, Manual Call Points and other devices that can be
Loop Device
connected to the Loop.
Loop Module A Module supplying power and is in charge of communication to the loop devices.
The opposite of Controller Mode. All modules that are managed by a Controller
Managed Mode
Module are in Managed Mode.
MCS Multi Central System. A System consisting of more then one Central.
MFZ Main Fire Zone.

5100333-02B02 43
8 Appendix Installation Manual

Modules in the System can take on different roles. Connected to the Backbone Bus
they can be in:
• Central Controller Mode (Master or Hot Standby)
• Central Managed Mode
Mode of operation
Modules connected to the System Bus can be in:
• System Controller Mode (Master or Hot Standby)
• System Managed Mode

A module that is a part of the Platform, that is can be used to build Centrals. Modules
Module within the platform generally supply a Backbone Bus interface. Controller Modules
also have a System Bus Interface.
Module Address Module Addresses are set via DIP switches on the Modules.
Mute Acknowledge and silence the local buzzer and in some cases the alarm devices.
PA Public Addressing.
Power Output Output providing power supply, normally used to power external devices.
A condition preceding the Alarm Condition to give early warning for potentially
Pre-Alarm Condition
dangerous situations like a smouldering fire.
Programmable Output Output which signal behaviour is configurable via the Configuration Program.
PSU Power Supply Unit.
Refers to the quality or state of being redundant, that is exceeding what is necessary or
Redundancy normal. In the System the term is used to describe backup functionality like in Hot
Standby Controller Modules.
Electrically operated switch output, normally providing C/NO/NC contacts for
Relay
connection of signal receiver.
The main attribute for Repeater Panels is that they can show information but not affect
Repeater Panel
the Central (or System) they belong to. The Repeater M 4.3 is a Repeater Panel.
Modules enter 'safe state' when they detect system faults. Modules in Safe State put
Safe State their I/O in a predefined state and stop all communication in order to avoid disturbing
system integrity.
SCS Single Central System.
Salwico Safety Management interactive graphics, a PC-based software package
SMig system
providing graphical presentation and control of the System.
A central that is physically distributed to two or more physical locations. One location
Stretched central (DCS) may or may not supply power to another location (segmented) and two locations may
or may not have isolated communication lines.
A signal in the Backbone Bus that is used for transmitting synchronization signal used
Synchronization Signal
by system Modules to synchronize there behaviour.
System A System consists of one or more Centrals.
The communication bus used for connecting multi-central systems. The System Bus is
used for inter-central communication but can also be used for external communication.
System Bus
If inter-central communication redundancy is required, the system bus will consist of a
primary and a secondary System Bus.
Terminal A Terminal is a physical point of connection, compare I/O pin.
Detectors put in the Test Condition (or Test Mode) are inhibited from generating the
Test Condition Alarm Condition but the alarms are displayed on the Control Panels to prove that the
tested Detectors are operational.
Universal Serial Bus, a communications bus that may be used to connect flash
USB
memories, keyboards, mice or other devices.

44 5100333-02B02
Installation Manual 8 Appendix

The state of the system when a warning is detected. Warnings are not as serious as
Warning Condition faults and only of informative nature, for example that a Gas Detector is in need of
calibration.
Zone A group of detectors located in a geographical area.

5100333-02B02 45
8 Appendix Installation Manual

46 5100333-02B02
 Index

Index
A H
About testing.......................................................... 14 Heat detector, Installation guidelines..................... 22

B I
Backbone Bus External (BBE), Electrical I/O M 70................................................................. 31
installation.............................................................. 8 I/O M 70, Connection to ........................................ 9
Bells, Installation guidelines.................................. 24 I/O M 700............................................................... 31
Bus Isolator M........................................................ 31 Installation guidelines, Cabling and electrical
installation.............................................................. 25
Installation order, Mechanical installation............. 7
C IS Smoke detector for EX areas, Installation
Cable requirements, Electrical installation ............ 8
guidelines ............................................................... 23
Cabling, Installation guidelines ............................. 25
Central status.......................................................... 19
Central unit terminal layout with cabling .............. 31 L
Change Over M Ext ............................................... 31 Loop M X............................................................... 31
Charger M .............................................................. 31 Loop configuration................................................. 19
Cold room Heat detectors, Installation guidelines. 24 Loop status ............................................................. 19
Commissioning requirements ................................ 19 Loop units, Mechanical installation....................... 7
Control M 2.2......................................................... 31 Loops, Verification of ............................................ 13
Control M X........................................................... 31
Control Panel M 4.3............................................... 31
Control Panel M 4.3, Installation order ................. 7
M
Manual call points, Installation guidelines ............ 24
Control panel display, Testing................................ 15
Muting faults, Trouble shooting............................. 16
Control panels, Mechanical installation................. 7
Control panels, Electrical installation .................... 11
Conventional high temperature Heat detectors, P
Installation guidelines ............................................ 23 PSU M AC/DC 5A ................................................ 31

D R
Detector loops, Cable requirements....................... 8 Relay M 8............................................................... 31
Disablement list ..................................................... 15 Repeater M 4.3....................................................... 31
Door holder magnet 130kp, Installation Reset faults, Trouble shooting ............................... 16
guidelines ............................................................... 24 Reset test mode ...................................................... 15
Door holder magnet 65kp, Installation guidelines. 24 RS485 Termination ................................................ 33
Door release switch, Installation guidelines .......... 24 RS485, Application examples for installation ....... 33

E S
Earth fault, Trouble shooting ................................. 16 Smoke detector, Installation guidelines ................. 21
Electrical siren, Installation guidelines .................. 24 System modules, Description................................. 31
Electrical equipment, Location of.......................... 28
T
F Terminal layout, Electrical installation .................. 10
Fault list ................................................................. 16 Test Equipment ...................................................... 0
Fault list ................................................................. 16 Test for earth failure............................................... 9
Fire detection system, System description............. 5 Test mode overview ............................................... 14
Fire detection system, System data........................ 6 Test the control panel display ................................ 15
Fire history list ....................................................... 14 Testing a fire-detecting zone .................................. 14
Fire history list ....................................................... 15
Flame detectors, Installation guidelines................. 22
Z
Zone, Test mode..................................................... 14
G
Guidelines, Loop units installation ........................ 21

5100333-02B02 47
Index

48 5100333-02B02
Global Service and Support

Own companies
Sales- and service representatives

Consilium is constantly increasing and improving its global sales and service
organisation in order to provide our customers with the most competent
service and support. Today Consilium has established own companies in
16 countries plus sales and service representatives in more than 50 countries.
You will find updated contact information on our web-site www.consilium.se.

www.consilium.se
 Fire alarm central
Salwico Workboat CI
Part no. 5102013-01A

General description

Salwico Workboat CI is a conventional fire detection system with 8 fire detector sections SOLAS
compliant. Tested and certified by all major classification societies, this system provides an optimal fire
detection solution for smaller vessels.

The system is managed and supervised through Control Panel M 4.3. The Control Panel M 4.3 is
mounted on the front of the fire alarm cabinet.

The central is delivered complete with:

 1 x Control panel M 4.3, Internal

 2 x Power supply AC/DC 2.5A (A 24 VDC kit can be ordered separately).
 1 x I/O 70, for 8 conventional sections
 8 pre-configured powered outputs 24 VDC. (Max. consumption 1.8 A)
 Batteries 24V, 1,3Ah
 Optional serial interface (NMEA)

The cabinet is for wall mounting.

One multi flange for cable inlet is included in the delivery.

Data

Nominal voltage 100-240VAC

Power consumption ~10W in normal condition
Heat emission ~25 Kcal/h
Ingress Protection IP32
Cable terminals 2.5mm2
Temperature range -5°C to +55°C
Material, cabinet Steel
Colour, cabinet RAL7035
Weight ~10,5 kg

Related Parts

5100088-00A PSU M DC/DC 5A

5102024-00A Relay Kit Workboat

Consilium Marine & Safety AB

P.O. Box 8763, SE-402 76 Göteborg
Phone +46 31 7107700 Fax +46 31 7107800
www.consilium.se
Page 1 of 4
Wall mounted cabinet dimensions (mm)

Consilium Marine & Safety AB

P.O. Box 8763, SE-402 76 Göteborg
Phone +46 31 7107700 Fax +46 31 7107800
www.consilium.se
Page 2 of 4
Power Supply Connection:

NOTE:
If external DC power source is used this must be adjusted to 28.5V. A separate DC/DC kit is available in case this requirement
can’t be fulfilled.

Consilium Marine & Safety AB

P.O. Box 8763, SE-402 76 Göteborg
Phone +46 31 7107700 Fax +46 31 7107800
www.consilium.se
Page 3 of 4
Equipment Connections

Optional relay kit connections:

Consilium Marine & Safety AB

P.O. Box 8763, SE-402 76 Göteborg
Phone +46 31 7107700 Fax +46 31 7107800
www.consilium.se
Page 4 of 4