A.

Corrections/standarization of SPT value for field procedure for all type of soil
EHCBCSCRN
N60 =
0.6
Where,
N60 Corrected SPT value for field procedure for all type of soil
EH Hammer efficiency (Table 6.D.4)
CB Borehole diameter correction (Table 6.D.5)
CS Sampler correction (Table 6.D.5)

CR Rod length correction (Table 6.D.5)

N Measured SPT N-value in field

Table 6.D.4 SPT Hammer Efficiency

Hammer
Hammer Type release Efficiency, EH
mechanism

Automatic Trip 0.7

0.6
Donut Hand dropped
Cathead+2 0.5
Donut turns
Cathead+2 0.55 to 0.60
Safety turns

0.45
Drop/Pin Hand dropped

Table 6.D.5 Borehole, Sampler and Rod correctoin facors

Factor Equipment Correction

Variables factor
65mm- 1
CB 115mm
150mm 1.05
200mm 1.15
Standard 1
CS sampler

Sampler 1.2
without liner
CR 3m-4m 0.75
4m-6m 0.85
 6m-10m 0.95
>10m 1

B. Corrections of SPT value for overburden pressure for all types of cohesionless soils

(N1 )60 = CN x N60

Where,
(N1)60 Correction of overburden
CN = 0.77Log(2000/σ'0 )
Where,
σ'0 Effective overburden pressure

C. Correction of SPT value for water table(Dilatancy) in case of Fine Sand and Silty Sand
(in addition to correction for overburden pressure)
(N1)60(CORR) = 15+0.5[(N1)60 - 15]
Where,
(N1)60(CORR) corrected (N1)60 for water table
(for coarse sand this correctoin is not required)
(Overburden correction is applied first then dilatancy)
D. SPT Vs peak angle of internal frictoin for
Ф0 = 27+0.3(N1)60
OR
Ф0 = sqrt[20(N1)60] +15

Table 6.D.7: Penetration resistance and soil properties on the basis of SPT(cohesive soil)
UC
N-value Consistency strength(qu )
kN/m2
0-2 Very soft <25
2-4 soft 25-50
4-8 medium 50-100

8-15 100-200
stiff
15-30 very stiff 200-400

>400
>30 hard

E. SPT Vs qu for clay

qu (kN/m2)= 12.5 N60 for normal clay

qu (kN/m2)= 10 N60 for hoghly plastic PI>30
Capacity of Precast Pile as per BNBC-2020

Use 'c' for plastic silt and clay and 's' for sand and nonplastic silt

Input:
Pile Dia: 0.40 m
Water Table 3.50 m
FOS : 2.5
Shaft area 1.91m2
Base area 0.13m2

N60 Soil Type

soil Unit Wt.
Depth(ft) Depth(m) (kN/m3) yw (kN/m3) σ'0 (kN/m2) CN
0 0.00
5 1.52 4.7 s 17 0 25.91 1.45
10 3.05 7.5 s 19 0 54.88 1.20
15 4.57 3.2 c 19 9.8 68.90 1.00
20 6.10 3.6 c 19 9.8 82.93 1.00
25 7.62 9.5 c 19 9.8 96.95 1.00
30 9.15 15.4 c 19 9.8 110.98 1.00
35 10.67 12.5 c 19 9.8 125.00 1.00
40 12.20 11.3 c 19 9.8 139.02 1.00
45 13.72 10 c 19 9.8 153.05 1.00
50 15.24 25 c 19 9.8 167.07 1.00
55 16.77 21.3 c 19 9.8 181.10 1.00
60 18.29 15 c 19 9.8 195.12 1.00
65 19.82 17.5 s 19 9.8 209.15 0.76
70 21.34 32.5 s 19 9.8 223.17 0.73
75 22.87 35 s 19 9.8 237.20 0.71
80 24.39 35 s 19 9.8 251.22 0.69
85 25.91 41.3 s 19 9.8 265.24 0.68
90 27.44 45 s 19 9.8 279.27 0.66
95 28.96 50 s 19 9.8 293.29 0.64
100 30.49 55 s 19 9.8 307.32 0.63
105 32.01 0 0 0 9.8 292.38 1.00
110 33.54 0 0 0 9.8 277.44 1.00
Equation:
 allowable
Ult skin Ult skin
friction(k friction(kN/
(N1)60 (N1)60(CORR) Ф0/cu ά β ά/β σ'0 (kN/m2) N/m2) m2)

6.83 6.83 26.69 0.00 0.1 0.10 25.91 2.59 2.59

9.02 9.02 28.43 0.00 0.1 0.10 54.88 5.49 5.49
3.20 3.20 16.00 1.00 0 1.00 68.90 16.00 16.00
3.60 3.60 18.00 1.00 0 1.00 82.93 18.00 18.00
9.50 9.50 47.50 0.68 0 0.68 96.95 32.23 32.23
15.40 15.40 77.00 0.50 0 0.50 110.98 38.50 38.50
12.50 12.50 62.50 0.46 0 0.46 125.00 29.02 29.02
11.30 11.30 56.50 0.55 0 0.55 139.02 31.08 31.08
10.00 10.00 50.00 0.64 0 0.64 153.05 32.14 32.14
25.00 25.00 125.00 0.50 0 0.50 167.07 62.50 62.50
21.30 21.30 106.50 0.50 0 0.50 181.10 53.25 53.25
15.00 15.00 75.00 0.50 0 0.50 195.12 37.50 37.50
13.21 13.21 31.26 0.00 0.1 0.10 209.15 20.91 20.91
23.83 19.42 36.83 0.00 0.339552 0.34 223.17 75.78 60.00
24.95 19.98 37.34 0.00 0.35 0.35 237.20 83.02 60.00
24.28 19.64 37.04 0.00 0.35 0.35 240.00 84.00 60.00
27.90 21.45 38.62 0.00 0.35 0.35 240.00 84.00 60.00
29.63 22.31 39.34 0.00 0.35 0.35 240.00 84.00 60.00
32.10 23.55 40.34 0.00 0.35 0.35 240.00 84.00 60.00
34.45 24.72 41.25 0.00 0.35 0.35 240.00 84.00 60.00
0.00 0.00 0.00 0.00 0 0.00 240.00 0.00 0.00
0.00 0.00 0.00 0.00 0 0.00 240.00 0.00 0.00
 allowable
ult skin ult end ult end ult end
friction(k cum ult skin bearing(k bearing(kN/ bearing(k allowable
N) friction(kN) Nq N/m2) m2) N) capacity(kN)

4.96 4.96 18.675799 483.9765 483.98 60.78745 26.30

10.50 15.46 25.553125 1402.306 1402.31 176.1296 76.64
30.63 46.09 0 144 144.00 18.0864 25.67
34.45 80.55 0 162 162.00 20.3472 40.36
61.70 142.24 0 427.5 427.50 53.694 78.37
73.69 215.94 0 693 693.00 87.0408 121.19
55.54 271.48 0 562.5 562.50 70.65 136.85
59.48 330.96 0 508.5 508.50 63.8676 157.93
61.53 392.49 0 450 450.00 56.52 179.60
119.63 512.12 0 1125 1125.00 141.3 261.37
101.93 614.05 0 958.5 958.50 120.3876 293.78
71.78 685.83 0 675 675.00 84.78 308.24
40.03 725.87 42.498305 8888.365 8888.36 1116.379 736.90
114.85 840.71 115.96007 25878.89 11000.00 1381.6 888.93
114.85 955.56 127.04308 30134 11000.00 1381.6 934.87
114.85 1070.41 120.29943 28871.86 11000.00 1381.6 980.80
114.85 1185.26 160.04105 38409.85 11000.00 1381.6 1026.74
114.85 1300.11 182.15374 43716.9 11000.00 1381.6 1072.68
114.85 1414.96 217.8971 52295.31 11000.00 1381.6 1118.62
114.85 1529.81 256.74295 61618.31 11000.00 1381.6 1164.56
0.00 1529.81 0 0 0.00 0 611.92
0.00 1529.81 0 0 0.00 0 611.92
 33 0.1
35 0.2
37 0.35

angle 27
beta -0.2833

Chart Title
700

600

500
f(x) = 0.153092875291835 exp( 0.18000330567188 x )

400

300

200

100

0
20 25 30 35 40 45 50
 25 17
26 19
27 21
28 25
29 29
30 34
31 38
32 45
33 50
34 60
35 70 31.38
36 90 43.45544
37 100
38 140
x) 39 170
40 200
41 250
42 300
43 380
44 500
45 600

45 50