K2 Summit 3G 1. Make cable connections 2.

Start up
Production Client Standard bi-directional channels SDI connections Ethernet cabling
Quick Start Guide
071-8873-01 January 8, 2013 Each channel (C1, C2, etc.) can be an input IN1 IN2 IN3 Internal or direct-connect storage: 1 Before power on, take
(record channel) or an output (play channel). -Port 1 - Control network note of the chassis serial
Before you begin, unpack the following items. Standard or 3G* Active -Port 2 - FTP/Streaming
Connect video/audio IN and OUT to each number, located behind
Multi-Cam** Video1 Video2 -Ports 3 & 4 - Not used the bezel/fan.
channel, as appropriate for your intended
Recovery Flash Drive contains: 3D/Video + Video Key Shared iSCSI storage basic:
PDF use. Key record** (L eye) (R eye) 2 Identify the Recovery Flash
-K2 Release Notes Adobe
-Port 1 - Control network
-K2 Doc Set Super Phase Phase Phase -Port 2 - Media (iSCSI) network Drive, which is labeled with
K2 Summit 3G Production Client
-Software and disk images. Slo-Mo** 1 2 3 2 Connect
1 Shared iSCSI storage redundant: this unit’s serial number.
1 Make SDI connections on each channel
NOTE: Do not lose the Recovery Flash network cables -Port 1 & 4 - Control network Make sure it remains stored
Rack slides Drive. It contains the recovery disk OUT1 OUT2 to Ethernet -Port 2 - Media (iSCSI) network A with this specific unit.
image for this specific K2 Summit -Port 3 - Media (iSCSI) network B
Licenses and system. Connections per channel (C1, C2, etc) Standard or 3G* Active Active ports
up
ro
ll
a

us s uss s s
us up

s s s s
us s us s

Shared FC storage basic:

ss

ro
ra

2 Replace the bezel/fan

3
usra s uss s s
ll
a

ra ss ra ss s s s s
us s us s

Duplicates OUT1
s

ro up ro up
us
ss

ro

ro up ro up
ra

s
us

up
ss a llss as ll

Warranties
a

a ll a ll
roll
us

ra ss ra ss

up

GigE Ports
a

SDI video in
ll

-Port 1 - Control network

ra

3D/Video + Video Key and identify the following: Service Standby Power
and out. 2 3
Shared FC storage redundant:
Power cords LTC cables Supports Key play** (L eye) (R eye) LED switch LED
1 4 -Port 1 & 4 - Control network
AES embedded LTC Super Out** Active Super Out info 3 Press the standby switch
4
audio audio. I/O RS-422
Locate the documentation you need on the to power on. Normal startup sequence
Recovery Flash Drive or download from SDI Connections: Power LED goes on and
C1 C2 C3 C4
http://www.grassvalley.com/dl/k2_summit * 3G requires license 5 Log on with the default
3 stays on. Service LED
Documentation path to install ** Some connections Windows admin account: stays off.
K2 Summit system with internal storage require special license -Username: Administrator
PDF
and configuration -Password: adminGV!
Adobe
C1 C2 C3 C4
Release Quick Start System OK OK Refer to K2 AppCenter
Notes Guide Guide ! !
User Manual. 6 On the Windows desktop, check the system
3
GPI

~AC ~AC
tray. When the network icon indicates connectivity,
VGA
the K2 Summit system is operational.
Documentation path to install USB/1394 100BT/1000BT REF. LOOP THROUGH

Make other connections as

K2 Summit systems with SAN or direct-connect storage
PDF Gra
ley
ss Val
5 Connect
1 Optional Fibre Channel card 3 1 Connect keyboard 4 Connect VGA
1 5 Connect
1 needed. Refer to the K2
xx

K2flxxxxx
xx
xx
xx

System Guide for complete

xx
xx
xx

xxx

power power
flxx

Adobe
flxx
xxx

for connection to standalone and mouse monitor

Release *Cabling SAN Manual System Quick Start cord direct-connect storage or cord instructions.
Notes Guide (shared storage) Guide Guide shared Fibre Channel storage.
*Cabling Guide packed with RAID primary chassis

3. Configure network and, if necessary, storage 4. Configure channels

1 Use SiteConfig as appropriate for your K2 system and on-site networking.
3 1 Open AppCenter and logon with the administrator account
(User Name=Administrator/Password=adminGV!). If a
Stand-alone internal or direct-connect storage – Install Default network settings licensing message appears, refer to K2 Release Notes.
SiteConfig on a control point PC, discover the K2 Summit
Production Client, and configure network interfaces. DHCP is enabled and the 2 Click System | Configuration.
- Configure Control Team for the control network. chassis serial number is A
the hostname. er
nte
- If desired, configure Media Connection #1 for the AppCe

FTP/Streaming network.
Refer to K2 Release Notes for instructions. Ethernet connection names
Shared storage – Configure network This rear panel Is named this in Windows
interfaces as instructed in the K2 SAN GigE port... Network Connections...
Installation and Service Manual. 1 Control Team (Control
Connection #1)
2 Configure network name resolution via host
3 3 C
Click tabs,
2 Media Connection #1 b
buttons, and
files or otherwise, as required by on-site
3 Media Connection #2 scroll bar to
sc
networking. FTP/Streaming network locate settings.
lo
hostnames must include “_he0” suffix. 4 Control Team (Control
Connection #2) 4 S
Select from
3 Configure storage as follows: d
drop-down lists
Internal storage – No storage configuration is necessary. Storage is pre-configured. to make settings.
Direct-connect storage – Use Storage Utility to Bind RAID disks and make file system. 5 C
Click OK and
Refer to the K2 System Guide. Y to save
Yes
Shared storage – Use the K2 System Configuration application to add the K2 Summit settings.
se
Production Client to the K2 SAN and configure it on the SAN. Refer to the K2 SAN
Installation and Service Manual.
 5. Record and play 8. Record and
6. Create play
a playlist
Bi-directional channels
A channel becomes an input 3 Stop record
channel when you begin
1 Select a channel 1 Select Playlist 2 Drag clips into
recording. The same channel 2 Begin record
the channel
becomes an output channel
when you load a clip for
playout.

4 Drag a clip into the

channel
5 Adjust audio level
6 Play the clip 3 Play the list
as needed
Timecode for Record
On the AppCenter menu, click
Control | Options. On the
Options dialog box click
Timecode and select the
Refer to the AppCenter Help menu for complete information about playlist
timecode for recording and
functionality and other operations, such as editing subclips.
display.

7. Monitor 8. For more information...

In AppCenter, click Help | AppCenter Help Topics and Find the complete documentation set for K2 products
read the complete documentation for operating and in the K2/STRATUS Doc Set zip file on the Recovery
Click View | Video Monitor configuring K2 Summit system channels. Flash Drive or by downloading from
http://www.grassvalley.com/dl/k2_summit:
Toolbar
Help
Full Screen - User Guide
System Status - System Guide
Video Monitor
- Service Manual
AppCenter Help Topics
- SAN Manual
About AppCenter - Cabling Guide
Video monitor support
The VGA resolution must be
1024 x 768 x 32 or greater to Use the following information to contact
support live (moving) video Go to http://www.grassvalley.com/support and find product support by phone during business
solutions to problems. hours. Afterhours phone support is available
monitoring. for warranty and contract customers.

North America +800 547 8949

+1 530 478 4148

International For local phone and email support go to:

http://www.grassvalley.com/support/contact

Copyright © Grass Valley USA, LLC. All rights reserved.