Scribd
Upload
4 views2 pages

SolidMech MidSem

Uploaded by

Chitresh Pratap Singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
4 views2 pages

SolidMech MidSem

Uploaded by

Chitresh Pratap Singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Mid Term Solid Mechanics

Instructions
the and the answer shect. 3) Draw necessary
1) No pencil, no credit. 2) Read
instructions carcfully sign

label Use to draw frcc-body diagramns 4) Usc the


Sign Convention. FBD and properly
a
straight-cdge

it.
Units and Vicc Versa. 5) Prescnt
units given in the problem. change from SI units to US Customary
Do not
in a clcar, legible and logical manner, 6) Use the conventional units. 7) Assume data if not
your solutions
closcd notes cxam. So no material is allowcd cxcept the
provided in the problem. 8)1his book,
is a closcd

and answer shect


question paper providcd.
cnd
Problem 1:The fixcd-cnd bar ABCD consists of three prismatic segments, as shownin the Figure.The
840 and Li200 mm. The middlc Aluminum
stecl segmcnts havc cross- scctional arca A1 mm length

segment has cross-scctional arca A2 1260 mm and length L2 250 mm. Loads P and Pe arc cqual to
25.5 kN and 17.0 kN, respectively. Draw the a) Axial Force diagram b) Axial strain Diagram c) Deflection
for the entire body.
Diagram

dz
PB Pc

- Li L2 -L
cross sections is held between
Problem 2: A plastic bar ACB having two differcnt solid circular

shown the Thc diamctcrs in the left- and right-hand parts are 50 mm
supports as
in figurc.
rigid

and 75 mm, respectively. The corresponding lengths arc 225 mm and 300 mm. Also, the modulus
of thcrmal expansion a is 100 10/° C. The bar is X
of clasticity E is 6.0 GPa, and the cocfficicnt
to a uniform temperature increase of 30° C. Calculatc the following quantities: (a) thc
subjected
and the displacement
compressive forcc P in the bar; (b) the maximum compressivc stress Oc, (c)

Oc ofpoint C.

50mnm 75 mm B
1

-225mm -300 mnm-


Problem 3: A plastic
bar of diameter 30 d= mm is compresscd in a testing device by a force P=
the normal and shcar stresses acting on all faccs
170 N applicd as shown in the figure. Determine
45°
ofstress clements oriented (a) an angle 0-0°,(b)
at an angle 0
22.5°, and (c) an angle 0
.In cach casc, show the stresses on a skctch of' a properly oricnted clement.
P 170 N
100mm 300 mm

oT Plastic bar

d 30 mm

Problem 4:A bcam AlBC with cros scctional propertics b75 mm, t-25 mm, h= 100 mm, and hi

75 mm is simply supportcd at A and B and has an overhang BC. The bcam is loaded by twvo

forces P- 100 kN and aclockwise couple of moment Pa-50 kNm that act through the arrangement
shown. Draw the a) shcar-force and bending-momentdiagrams for bcam ABC. b) Determinc
normal stresses at Point B, c) Determine maximum normal stresses

Pa

AL
Steel

range for Poisson'sratio. b) Draw the Engincering curve


Problem 5: a) Derive the theoretical Stress-Strain
and True Stress-Strain Curve for Steel and Aluminum and clearly mark all the
relevant points.
Problem 6: A short column of wide-flange shape is subjected to a compressive load that produces
a resultant force P 60 KN acting at the midpoint of onc fange. (a) Determinethe maximum
tensile and compressive stresses oy and oo, respetivcly, in the column. (b) Locate the neutral axis

under this loading condition.

P 60 kN

8 mm
200
mm
12 mm
160
mm

You might also like