Scribd
Upload
20 views15 pages

Programmable Logic Controller

Uploaded by

Mohammed Tofiq
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
20 views15 pages

Programmable Logic Controller

Uploaded by

Mohammed Tofiq
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

Kurdistan region government

Ministry of higher education and scientific research


Sulaimani Polytechnic University
Chamchaml Technical Institute
Electrical techniques department

Programmable Logic Controller


3rd and 4th semester PLC practical course
for 2nd stage students

Prepared by:
Asst.Lec. karzan M. Taqi
2025
Experiment No. : (1)
Experiment Name:
Demonstrate ON OFF push buttons

Aim of the Experiment:


Learn how to use on / off push bottoms

Ladder Diagram:

Procedure:
Connect the circuit as shown in figure above
Adjust both I1 and I2 as momentary make push buttons

Discussion:
Try to figure away in order to make Q1 stay on after release I1
Experiment No. : (2)
Experiment Name:
Connecting and demonstrate of operating a contactor using ON/ OFF push
buttons

Aim of the Experiment:


Learn to use ON / OFF push buttons to operate a contactor and keep the output
Q ON after releasing push button

Ladder Diagram:

Procedure:
Connect the circuit as shown in figure above

Set both I1 and I2 as (make) and (break)

Discussion:
Use alternative circuit to do the same job with out using Q physical output?
Experiment No. : (3)
Experiment Name:
Connect and using timer function

Aim of the Experiment:


Learn to use timer function to control work sequence

Ladder Diagram:

Procedure:
Connect the circuit shown above

Discussion:
Use the timer function to establish a traffic light controller for one street
direction
Experiment No. : (4)
Experiment Name:
Connect and using counter up / down function

Aim of the Experiment:


Learn to use counter up / down function to control work sequence

Ladder Diagram:

Procedure:
Connect the circuit shown above

Make sure I1 and I2 are make and I3 is switch

Discussion:
Use the counter up / down function to establish a garage gate controller
Experiment No. : (5)
Experiment Name:
Connect and using threshold counter function

Aim of the Experiment:


Learn to use threshold counter function to control work sequence

Ladder Diagram:

Procedure:
Connect the circuit shown above

Discussion:
Use the threshold counter function to costomize the traffic light to optimize the
time in traffics
Experiment No. : (6)
Experiment Name:
Operating motor in Forward / Reverse mode

Aim of the Experiment:


Learn how to control the operation of 3 phase induction motor in both direction
(clockwise/counter clockwise) using only plc and two contactors

Ladder Diagram:

Procedure:
Connect the diagram shown above make sure

(I1) is make

(I2) is make

(I3) is make

Discussion:
Add timer delay between the conversions in order to stop the motor before start
it in reverse
Experiment No. : (7)
Experiment Name:
Operating motor in star / delta mode

Aim of the Experiment:


Learn how to control the operation of 3 phase induction motor in star / delta
mode

Ladder Diagram:

Procedure:
Connect the diagram shown above make sure

Discussion:
Design the circuit above in soft control mode
Experiment No. : (8)
Experiment Name:
Controlling garage gate open and close operation

Aim of the Experiment:


Learn how to control the operation of 3 phase induction motor in both direction
(clockwise/counter clockwise) using only plc and two contactors

Ladder Diagram:

Procedure:
Connect the diagram shown above make sure

Discussion:
Add timer delay for open mode to close later and add a sensor if the vehicle is
inside to close the gate before the time finish counting.
Experiment No. : (9)
Experiment Name:
Connecting AND / OR gates in ladder

Aim of the Experiment:


Learn how to use switches to control process using logic gates

Ladder Diagram:

Procedure:
Connect the diagram shown above make sure

Discussion:
Experiment No. : (10)
Experiment Name:
Shift register function

Aim of the Experiment:


Learn how to use shift register function and demonstrate the output of the shift
register

Ladder Diagram:

Procedure:
Connect the diagram shown above make sure
Experiment No. : (11)
Experiment Name:
Answer fast circuit diagram

Aim of the Experiment:


Learn how to analysis problem requirements and figure out the needs
Ladder Diagram:

Procedure:
Connect the diagram shown above make sure
Experiment No. : (12)
Experiment Name:
Write program to operate a mixer

Aim of the Experiment:


Learn how to control mixer process in a factory

Ladder Diagram:
Connect write program for the process below

Procedure:
Connect the diagram shown above make sure

Discussion:
Add another step to the process with timer

You might also like