CLOVER DISPLAY LTD.

LCD MODULE SPECIFICATION

Model : ZCG12864R - _ _ - _ _ - _ _ -

Revision 00
Engineering PANWU
Date 23 JAN 13
Our Reference

ADDRESS : BLOCK B4, SHAHE INDUSTRIAL TOWN, NANSHAN, SHENZHEN, CHINA

TEL : (86) 755-8609 6773 (SALES OFFICE) (86) 755-8609 3711 (GENERAL OFFICE)
FAX : (86) 755-8609 6870 (SALES OFFICE) (86) 755-8609 6971 (GENERAL OFFICE)
E-MAIL : [email protected]
URL : http://www.cloverchina.com
 CLOVER DISPLAY LTD. ZCG12864R

MODE OF DISPLAY
Display mode Display condition Viewing direction
STN : □ Yellow green □ Reflective type □ 6 O’ clock
□ Grey □ Transflective type □ 12 O’ clock
□ Blue (negative) □ Transmissive type □ 3 O’ clock
□ FSTN positive □ Others □ 9 O’ clock
□ FSTN negative

LCD MODULE NUMBER NOTATION:

ZCG12864R - N N - S F - N 6 – T *(1)---Model number of standard LCD Modules
| | | | | | | | *(2)---Backlight type
(1) (2) (3) (4) (5) (6) (7) (8) N – No backlight
E – EL backlight
L – Side-lited LED backlight
M– Array LED backlight
C – CCFL
*(3)---Backlight color
N – No backlight
A – Amber
B – Blue
O– Orange
W–White
Y – Yellow green
*(4)---Display mode
T – TN
V – TN (Negative)
S – STN Yellow green
G – STN Grey
B – STN Blue (Negative)
F – FSTN
N – FSTN (Negative)
*(5)---Rear polarizer type
R – Reflective
F – Transflective
T – Transmissive
*(6)---Temperature range
N – Normal
W– Extended
*(7)---Viewing direction
6 – 6 O’clock
2 – 12 O’clock
3 – 3 O’clock
9 – 9 O’clock
*(8)---Special code for other requirements
(Can be omitted if not used)

SPEC. REV.00 PAGE 1O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

GENERAL DESCRIPTION
Display mode : 128 x 64 dots, graphic COG LCD module
Interface : Serial
Driving method : 1/64 duty, 1/9 bias
Controller IC : Sitronix SPLC502B or equivalence
For the detailed information, please refer to the IC specifications.

-
MECHANICAL DIMENSIONS
Item Dimension Unit Item Dimension Unit
Outline Dimension 25.5(L)x 20.0(W)x 1.8MAX. (H) mm Dot Pitch 0.16(L)x0.18(W) mm
Viewing Area 23.5(L)x 14.0(W) mm Dot Size 0.14(L)x0.16(W) mm

CONNECTOR PIN ASSIGNMENT

Pin No. Symbol Function Pin No. Symbol Function
Power supply voltage for logic 15 VSS Ground
1 VDD
2 C86 8080 / 6800 MPU interface select 16 D7 Parallel mode: date bus
Serial mode: serial data imput (SI)
3 VSS Logic power supply(0V) 17 D6 Parallel mode: date bus
Serial mode: serial data imput (SCL)
4 V0 18 D5
5 V4 19 D4
6 V3 Power supply for LCD drive 20 D3 Data bus
7 V2 21 D2
8 V1 22 D1
9 CP2- 23 D0
10 CP2+ 24 RD(E) Read enable for 8080 MPU
Read/Write clock for 6800 MPU
11 CP1+ 25 /WR Write enable for 8080 MPU
Read/Write control for 6800 MPU
DC/DC converter for VLCD terminal
12 CP1- 26 A0 Date/Instruction select

13 CP3+ 27 /RES Reset terminal

14 VOUT 28 /CS Chip select terminal

SPEC. REV.00 PAGE 2O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

COUNTER DRAWING OF MODULE DIMENSION

SPEC. REV.00 PAGE 3O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

COUNTER DRAWING OF PIN OUT & BLOCK DIAGRAM

SPEC. REV.00 PAGE 4O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

LECTRICAL CHARACTERISTICS Conditions: VSS=0V, Ta=25 ℃

Item Symbol MIN. TYP. MAX. Unit
Supply Voltage for Logic VDD 2.75 3.0 3.25 V
Supply Current for Logic IDD － 130 160 uA
Operating Voltage for LCD(*) VLCD 7.6 8.0 8.4 V
‘High’ Level Input Voltage VIH 0.8VDD － VDD V
‘Low’ Level Input Voltage VIL VSS － 0.2VDD V
Note (*): There is tolerance in optimum LCD driving voltage during production and it will be within the specified range.

ABSOLUTE MAXIMUM RATINGS

Parameter Symbol Conditions Unit

Power supply voltage VDD -0.3~3.6 v

Power supply voltage ( VDD standard ) VDD2 -0.3~3.0 V

Power supply voltage ( VDD standard ) V0,Vlcd -0.3~+12 V

Power supply voltage ( VDD standard ) V1,V2,V3,V4 -0.3 to V0 V

Operating temperature TOPR -20 to 75 °C

Storage temperature Bare chip TSTR -55 to +125 °C

SPEC. REV.00 PAGE 5O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

REFERENCE CIRCUIT EXAMPLE

SPEC. REV.00 PAGE 6O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

INSTRUCTIONS

SPEC. REV.00 PAGE 7O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

SPEC. REV.00 PAGE 8O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

DISPLAY DATA RAM

SPEC. REV.00 PAGE 9O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

TIMING CHARACTERISTICS

SPEC. REV.00 PAGE 10O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

SPEC. REV.00 PAGE 11O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

SPEC. REV.00 PAGE 12O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

SPEC. REV.00 PAGE 13O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

THE SERIAL INTERFACE

SPEC. REV.00 PAGE 14O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

DISPLAY CONTROL OUTPUT TIMING

SPEC. REV.00 PAGE 15O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

RESET TIMING

SPEC. REV.00 PAGE 16O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

ELECTRO-OPTICAL CHARACTERISTICS
MEASURING CONDITION: POWER SUPPLY = VOP / 64 Hz
TEMPERATURE = 22 ± 5 °C
RELATIVE HUMIDITY = 60 ± 15 %

ITEM SYMBOL UNIT TYP. STN

Ton ms 220
RESPONSE TIME
Toff ms 280
CONTRAST RATIO Cr - 12
V3:00 ° 40
VIEWING ANGLE V6:00 ° 70
(Cr ≥ 2) V9:00 ° 40
V12:00 ° 50
THE ELECTRO-OPTICAL CHARACTERISTICS ARE MEASURED VALUE BUT NOT GUARANTEED ONES.

RELIABILITY OF LCD MODULE

TEST CONDITION TEST CONDITION

ITEM FOR NORMAL TEMPERATURE FOR WIDE TEMPERATURE TIME
High temperature operating 50°C 70°C 240 hours
Low temperature operating 0°C -20°C 240 hours
High temperature storage 60°C 80°C 240 hours

Low temperature storage -10°C -30°C 240 hours

Temperature-humidity storage 40°C 90% R.H. 60°C 90% R.H. 96 hours

Temperature cycling -10°C to 60°C -30°C to 80°C
5 cycle
30 Min Dwell 30 Min Dwell
Vibration Test at LCM Level Freq 10-55 Hz Freq 10-55 Hz

—
Sweep rate: 10-55-10 at 1 min Sweep rate: 10-55-10 at 1 min
Sweep mode Linear Sweep mode Linear
Displacement: 2 mm p-p Displacement: 2 mm p-p
1 Hour each for X, Y, Z 1 Hour each for X, Y, Z

SPEC. REV.00 PAGE 17O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

SAMPLING METHOD
SAMPLING PLAN: MIL-STD 105E
CLASS OF AQL: LEVEL II/ SINGLE SAMPLING
MAJOR-0.65 MINOR – 1.5

QUALITY STANDARD

DEFECT CRITERIA TYPE FIGURE

SHORT CIRCUIT - MAJOR -
MISSING SEGMENT - MAJOR -
UNEVEN / POOR CONTRAST - MAJOR -
CROSS TALK - MAJOR -
PIN HOLE MAX(a,b) ≤ 1/4W MINOR 1
EXCESS SEGMENT MAX(c,d) ≤ 1/4T MINOR 1
BUBBLES d* ≥ 0.2 QTY=0 MINOR 2
BLACKS SPOTS d ≤ 0.3 N.A.** MINOR 2
0.3<d≤0.4 QTY≤1
0.4<d QTY=0
LINE SCRATCHES x≥0.7 y≥0.05 QTY=0 MINOR 3
BLACK LINE x≥0.7 y≥0.05 QTY=0 MINOR 3
*d = MAX (d1,d2) ** N. A . = NOT APPLICABLE DEFECT TABLE : B

SPEC. REV.00 PAGE 18O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

QUALITY STANDARD ( CONT .)

DEFECT CRITERIA TYPE FIGURE

CONTACT EDGE e≤1/2T f≤1/3W g≤3.5 4
CHIPS BOTTOM GLASS p≤1.0 q≤3.5 r≤1/2T MINOR 4
CORNER a≤1.5 b≤W 4
TOP GLASS a≤3.0 b≤1/3T c≤1/2W 5
GLASS PROTRUSION a ≤ 1/4 W MINOR 6
RAINBOW - MINOR -
UNLESS STATE OTHERWISE , ALL UNIT ARE IN MILLIMETER . DEFECT TABLE : B

SPEC. REV.00 PAGE 19O F 2 0

 CLOVER DISPLAY LTD. ZCG12864R

HANDLING PRECAUTIONS
(1) CAUTION OF LCD HANDLING & CLEANING
Use soft cloth with solvent (recommended below) to clean the display surface and wipe lightly.
- Isopropyl alcohol, ethyl alcohol, trichlorotriflorothane

Do not wipe the display surface with dry or hard materials that will damage the polarizer surface. Do not
use the following solvent;
-water, ketone, aromatics

(2) CAUTION AGAINST STATIC CHARGE

The LCD modules use CMOS LSI drivers, so customers are recommend that any unused input terminal
would be connected to VDD or VSS , do not input any signals before power is turned on, and ground your
body, work/assembly areas, assembly equipment to protect against static electricity.

Remove the protective film slowly and, if possible, under ESD control device like ion blower and
humidity of working room should be kept over 50%RH to reduce risk of static charge.

(3) PACKAGING
Avoid intense shock and falls from a height and do not operate or store them exposed direct to sunshine
or high temperature/humidity.

(4) CAUTION FOR OPERATION

It is an indispensable condition to drive LCD’s within the specified voltage limit since the higher voltage
than the limit causes the shorter LCD life. The use of direct current drive should be avoided because an
electrochemical reaction due to direct current causes LCD’s undesirable deterioration.

Response time will be extremely delayed at low temperature, and LCD’s show dark color at high
temperature. However those phenomena do not mean malfunction or out of order with LCD’s.

Some font will be abnormally displayed when the display area is pushed hard during operation. But it
resumes normal condition after turning off once.

(5) SOLDERING (for Pin type)

It is recommended to complete dip soldering at 270 oC or hand soldering at 280 oC within 3 seconds. The
soldering position is at least 3mm apart from the pin head. Wave or reflow soldering are not
recommended. Metal pins should not be soldered for more than 3 times and each soldering should be
done after cool down of metal pins.

(6) SAFETY
For crash damaged or unnecessary LCD’s, it is recommended to wash off liquid crystal by either of
solvents such as acetone and ethanol and should be burned up later.

When any liquid leaked out of a damaged glass cell comes in contact with your hands, wash it off with
soap and water.

WARRANTY
CLOVER CHINA will replace or repair any of her LCD module in accordance with her LCD specification for
a period of one year from date of shipment. The warranty liability of CLOVER CHINA is limited to repair
and/or replacement. CLOVER CHINA will not be responsible for any subsequent or consequential event.

SPEC. REV.00 PAGE 20O F 2 0