V8 Replacement Guidance

[V6 series]

NEW
Convert

V6 series V8 series
- V6 series models
The V6 series models are listed below.
Check the following recommended models for replacement according to the current V6 series model.

V612□□□□□ V610□□□□□
None: 100 to 240 VAC None: 100 to 240 VAC
D: 24 VDC D: 24 VDC
None: Analog None: Analog
M: Matrix M: Matrix * There are no matrix switch types to
the V810S.
0: None 0: None
1: Video input 1: Video input
2: RGB input (V610T: analog type only)
1: Standard
2: Card interface 1: Standard
2: Card interface
T: TFT color LCD, SVGA T: TFT color LCD, VGA
C: STN color LCD, SVGA C: STN color LCD, VGA
S: TFT color LCD, SVGA

V609E30M□ V608C10
Standard
None: 100 to 240 VAC
D: 24 VDC
STN color LCD, VGA
Matrix type (touch switches)

SRAM + built-in clock function

High-luminance EL display unit

V608CH□ V606i□10□ V606□10□

None: Analog None: Analog
□ Deadman switch Key switch M: Matrix M: Matrix
0 Momentary None Standard Standard
1 Momentary Provided
T: TFT color LCD, QVGA C: STN color LCD, QVGA
2 3-position None
C: STN color LCD, QVGA M: STN monochrome LCD, QVGA
3 3-position Provided
M: STN monochrome LCD, QVGA

2
- Recommended models for replacement of V612 series (1)
V612T/V612C series Recommended models for replacement

V612Tx0 V612Tx0M V612Cx0 V612Cx0M V812S/V812SN V812SM/V812SMN

MONITOUCH

+0.5 +0.5
313 -0 313 -0

Panel cut-out
dimensions

246

246
(mm)

-0
+0.5

-0
+0.5
Display device TFT color STN color TFT color

Colors 128 colors 65,536 colors

Resolution 800  600 dots 800  600 dots

Touch switch Analog Matrix Analog Matrix Analog Matrix

D-Sub25pin: RS-232C/422
D-sub 25-pin: RS-232C/422/485 D-sub 9-pin: RS-232C/422/485
Communication I/F
Modular jack 8-pin (2D-Sub15pin: RS-422
ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/485

Power supply 85 to 265 VAC 100 to 240 VAC

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 When Hakko Electronics’ optional unit “TC485” is used, use an optional terminal converter “TC-D9”.
*3 When replaced with an analog switch model, two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*4 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V812SN or V812SMN. Use “CUN-xx” instead.

- Recommended models for replacement of V612 series (2)

V612T/V612C series Recommended models for replacement

V612Tx0D V612Tx0MD V612Cx0D V612Cx0MD V812SD/V812SDN V812SMD/V812SMDN

MONITOUCH

+0.5 +0.5
313 -0 313 -0

Panel cut-out
dimensions
246

246

(mm)
-0
+0.5

-0
+0.5

Display device TFT color STN color TFT color

Colors 128 colors 65,536 colors

Resolution 800  600 dots 800  600 dots

Touch switch Analog Matrix Analog Matrix Analog Matrix

D-sub 25-pin: RS-232C/422/485

D-Sub25pin:RS-232C/422 D-sub 9-pin: RS-232C/422/485
Communication I/F
Modular jack 8-pin (2D-Sub15pin:RS-422
ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/485

Power supply 24 VDC 24 VDC

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 When Hakko Electronics’ optional unit “TC485” is used, use an optional terminal converter “TC-D9”.
*3 When replaced with an analog switch model, two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*4 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V812SDN or V812SMDN. Use “CUN-xx” instead.

3
 V612T/V612C series Recommended models for replacement

V612Tx1 V612Tx1M V612Cx1 V612Cx1M V812iS/V812iSN V812iSM/V812iSMN

MONITOUCH

+0.5 +0.5
313 -0 313 -0

Panel cut-out
dimensions

246

246
(mm)

-0
+0.5

-0
+0.5
Display device TFT color STN color TFT color

Colors 128 colors 65,536 colors

Resolution 800  600 dots 800  600 dots

Touch switch Analog Matrix Analog Matrix Analog Matrix

D-sub 25-pin: RS-232C/422/485

D-Sub25pin:RS-232C/422 D-sub 9-pin: RS-232C/422/485
Communication I/F
Modular jack 8-pin (2D-Sub15pin:RS-422
ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/485

Power supply 85 to 265 VAC 100 to 240 VAC

Video 4CH Install an optional unit “GU-00” or “GU-10”.

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 When Hakko Electronics’; optional unit “TC485” is used, use an optional terminal converter “TC-D9”.
*3 When replaced with an analog switch model, two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*4 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V812iSN or V812iSMN. Use “CUN-xx” instead.

- Recommended models for replacement of V612 series (3)

V612T/V612C series Recommended models for replacement

V612Tx1D V612Tx1MD V612Cx1D V612Cx1MD V812iSD/V812iSDN V812iSMD/V812iSMDN

MONITOUCH

+0.5 +0.5
313 -0 313 -0

Panel cut-out
dimensions
246

246

(mm)
-0
+0.5

-0
+0.5

Display device TFT color STN color TFT color

Colors 128 colors 65,536 colors

Resolution 800  600 dots 800  600 dots

Touch switch Analog Matrix Analog Matrix Analog Matrix

D-sub 25-pin: RS-232C/422/485

D-Sub25pin:RS-232C/422 D-sub 9-pin: RS-232C/422/485
Communication I/F
Modular jack 8-pin (2D-Sub15pin:RS-422
ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/485

Power supply 24 VDC 24 VDC

Video 4CH Install an optional unit “GU-00” or “GU-10”.

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 When Hakko Electronics’ optional unit “TC485” is used, use an optional terminal converter “TC-D9”.
*3 When replaced with an analog switch model, two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*4 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V812iSDN or V812iSMDN. Use “CUN-xx” instead.

4
- Recommended models for replacement of V610 series (1)
V612T/V612C
V610S seriesseries Recommended
Recommendedmodels
models forfor replacement
replacement

V610Sx0 V610Sx0D V810S/V810SN V810SD/V810SDN

MONITOUCH

+0.5 +0.5
289 -0 289 -0

Panel cut-out

216.2

216.2
dimensions
(mm)

-0
+0.5

-0
+0.5
Display device TFT color TFT color

Colors 128 colors 65,536 colors

Resolution 800  600 dots 800  600 dots

Touch switch Analog Analog

D-sub 25-pin: RS-232C/422/485

D-Sub25pin:RS-232C/422 D-sub 9-pin: RS-232C/422/485
Communication I/F
Modular jack 8-pin (2D-Sub15pin:RS-422
ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/485

Power supply 85 to 265 VAC 24 VDC 100 to 240 VAC 24 VDC

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 When Hakko Electronics’ optional unit “TC485” is used, use an optional terminal converter “TC-D9”.
*3 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V810SN or V810SDN. Use “CUN-xx” instead.

- Recommended models for replacement of V610 series (2)

V610S series Recommended models for replacement

V610Sx1 V610Sx1D V810iS/V810iSN V810iSD/V810iSDN

MONITOUCH

+0.5 +0.5
289 -0 289 -0

Panel cut-out
216.2

216.2

dimensions
(mm)
-0
+0.5

-0
+0.5

Display device TFT color TFT color

Colors 128 colors 65,536 colors

Resolution 800  600 dots 800  600 dots

Touch switch Analog Analog

D-sub 25-pin: RS-232C/422/485

D-Sub25pin: RS-232C/422 D-sub 9-pin: RS-232C/422/485
Communication I/F
Modular jack 8-pin (2D-Sub15pin:
ports): RS-232C/485
RS-422 Modular jack 8-pin (2 ports): RS-232C/485

Power supply 85 to 265 VAC 24 VDC 100 to 240 VAC 24 VDC

Video 4CH Install an optional unit “GU-00” or “GU-10”.

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 When Hakko Electronics’ optional unit “TC485” is used, use an optional terminal converter “TC-D9”.
*3 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V810iSN or V810iSDN. Use “CUN-xx” instead.

5
 V610T/V610C series Recommended models for replacement
V810T/ V810TM/ V810C/ V810CM/
V610Tx0 V610Tx0M V610Cx0 V610Cx0M
V810TN V810TMN V810CN *4 V810CMN *4

MONITOUCH

+0.5 +0.5
289 -0 289 -0

Panel cut-out

216.2

216.2
dimensions
(mm)

-0
+0.5

-0
+0.5
Display device TFT color STN color TFT color

Colors 128 colors 65,536 colors

Resolution 640  480 dots 640  480 dots

Touch switch Analog Matrix Analog Matrix Analog Matrix Analog Matrix

D-sub 25-pin: RS-232C/422/485 D-sub 9-pin: RS-232C/422/485

Communication I/F
Modular jack 8-pin (2 ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/485

Power supply 85 to 265 VAC 100 to 240 VAC

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 When Hakko Electronic’ optional unit “TC485” is used, use an optional terminal converter “TC-D9”.
*3 When replaced with an analog switch model, two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*4 When a V6-specific optional FROM cassette “V6EM/4” or SRAM cassette “V6EM/RS” is in use, replace with V810iC/V810iCN or V810iCM/V810iCMN.
*5 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V810TN, V810TMN, V810(i)CN, or V810(i)CMN. Use “CUN-xx” instead.

- Recommended models for replacement of V610 series (3)

V610T/V610C series Recommended models for replacement
V810TD/ V810TMD/ V810CD/ V810CMD/
V610Tx0D V610Tx0MD V610Cx0D V610Cx0MD
V810TDN V810TMDN V810CDN *4 V810CMDN *4

MONITOUCH

+0.5 +0.5
289 -0 289 -0

Panel cut-out
216.2

216.2

dimensions
(mm)
-0
+0.5

-0
+0.5

Display device TFT color STN color TFT color

Colors 128 colors 65,536 colors

Resolution 640  480 dots 640  480 dots

Touch switch Analog Matrix Analog Matrix Analog Matrix Analog Matrix

D-sub 25-pin: RS-232C/422/485

D-Sub25pin: RS-232C/422 D-sub 9-pin: RS-232C/422/485
Communication I/F
Modular jack 8-pin (2D-Sub15pin:
ports): RS-232C/485
RS-422 Modular jack 8-pin (2 ports): RS-232C/485

Power supply 24 VDC 24 VDC

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 When Hakko Electronics’ optional unit “TC485” is used, use an optional terminal converter “TC-D9”.
*3 When replaced with an analog switch model, two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*4 When a V6-specific optional FROM cassette “V6EM/4” or SRAM cassette “V6EM/RS” is in use, replace with V810iCD/V810iCDN or V810iCMD/V810iCMDN.
*5 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V810TDN, V810TMDN, V810(i)CDN, or V810(i)CMDN. Use “CUN-xx” instead.

6
 V610T series Recommended models for replacement

V610Tx1 V610Tx1M V610Tx2 V810iT/V810iTN V810iTM/V810iTMN

MONITOUCH

+0.5 +0.5
289 -0 289 -0

Panel cut-out

216.2

216.2
dimensions
(mm)

-0
+0.5

-0
+0.5
Display device TFT color TFT color

Colors 128 colors 65,536 colors

Resolution 640  480 dots 640  480 dots

Touch switch Analog Matrix Analog Analog Matrix

D-sub 25-pin: RS-232C/422/485 D-sub 9-pin: RS-232C/422/485

Communication I/F
Modular jack 8-pin (2D-Sub25pin:RS-232C/422
ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/485
D-Sub15pin:RS-422
Power supply 85 to 265 VAC 100 to 240 VAC

Video 4CH None Install an optional unit “GU-00” or “GU-10”.

RGB input None 1CH Install an optional unit “GU-01” or “GU-11”.

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 When Hakko Electronics’ optional unit “TC485” is used, use an optional terminal converter “TC-D9”.
*3 When replaced with an analog switch model, two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*4 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V810iTN or V810iTMN. Use “CUN-xx” instead.

- Recommended models for replacement of V610 series (4)

V610T series Recommended models for replacement

V610Tx1D V610Tx1MD V610Tx2D V810iTD/V810iTDN V810iTMD/V810iTMDN

MONITOUCH

+0.5 +0.5
289 -0 289 -0

Panel cut-out
216.2

216.2

dimensions
(mm)
-0
+0.5

-0
+0.5

Display device TFT color TFT color

Colors 128 colors 65,536 colors

Resolution 640  480 dots 640  480 dots

Touch switch Analog Matrix Analog Analog Matrix

D-sub 25-pin: RS-232C/422/485 D-sub 9-pin: RS-232C/422/485

Communication I/F Modular jack 8-pin (2D-Sub25pin:RS-232C/422
ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/485
D-Sub15pin:RS-422
Power supply 24 VDC 24 VDC

Video 4CH None Install an optional unit “GU-00” or “GU-10”.

RGB input None 1CH Install an optional unit “GU-01” or “GU-11”.

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 When Hakko Electronics’ optional unit “TC485” is used, use an optional terminal converter “TC-D9”.
*3 When replaced with an analog switch model, two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*4 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V810iTDN or V810iTMDN. Use “CUN-xx” instead.

7
- Recommended models for replacement of V609E series
V609E series Recommended models for replacement

V609Ex0M V609Ex0MD V808CD/V808CDN

MONITOUCH

+1 +0.5
277 -0 220.5 -0

Panel cut-out

165.5 -0
dimensions

192
(mm)

+0.5
-0
+1
Use Hakko Electronics’ mounting panel adaptor “PAD-V608-01”.

Display device EL / high-luminance EL TFT color

Colors 2 colors By setting the display color to 128 colors,

65,536 colors
settings compatible with GD-80 are available.

Resolution 640  400 dots 640  480 dots The resolution of 640  400 is also available.

Touch switch Matrix Analog

D-sub 25-pin: RS-232C/422/485 D-sub 9-pin: RS-232C/422/485

Communication I/F
Modular jack 8-pin (2 ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/485

Power supply *4 100 to 240 VAC 24 VDC 24 VDC

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 To use a terminal block for connection, use Hakko Electronics’ optional terminal converter “TC-D9”.
*3 Two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*4 When there is no DC power supply available in the existing system, use Hakko Electronics’ optional unit “V808C-PW”.

- Recommended models for replacement of V608 series

V608C series Recommended models for replacement

V608C10 V808CD/V808CDN *3

MONITOUCH

+0.5 +0.5
-0 -0
220.5 220.5

Panel cut-out
165.5

165.5

dimensions
(mm)
-0
+0.5

-0
+0.5

Display device STN color TFT color

Colors 128 colors 65,536 colors

Resolution 640  480 dots 640  480 dots

Touch switch Analog Analog

D-sub 25-pin: RS-232C/422/485 D-sub 9-pin: RS-232C/422/485

Communication I/F Modular jack 8-pin (2 ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/485

Power supply 24 VDC 24 VDC

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable, use Hakko Electronics’ conversion cable “D9-D25”.
*2 To use a terminal block for connection, use Hakko Electronics’ optional terminal converter “TC-D9”.
*3 When a V6-specific optional FROM cassette “V6EM/4” or SRAM cassette “V6EM/RS” is in use, replace with V808iCD or V808iCDN.
*4 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V808(i)CDN. Use “CUN-xx” instead.

8
- Recommended models for replacement of V608CH series
V608CH series Recommended models for replacement

V608CH0 V608CH1 V608CH2 V608CH3 V808CH0 V808CH1 V808CH2 V808CH3

MONITOUCH

Display device STN color TFT color

Colors 128 colors 65,536 colors

Resolution 640  480 dots 640  480 dots

Touch switch Analog Analog

Communication I/F Terminal block (TB1) Terminal block: RS-232C (TB2) / RS-422/485 (TB3)

Power supply 24 VDC (TB1) 24 VDC (TB1)

*1 Use the V808CH-specific cable “V8H-C” as a PLC connection cable.

- Recommended models for replacement of V606i series (1)

V606iT series Recommended models for replacement

V606iT10 V606iT10M V806TD/V806TDN *4

MONITOUCH

+0.5 +0.5
174 -0 174 -0

Panel cut-out
dimensions
131

131

(mm)
-0
+0.5

-0
+0.5

Display device TFT color TFT color

Colors 16 colors 65,536 colors

Resolution 320  240 dots 320  240 dots

Touch switch Analog Matrix Analog

D-sub 25-pin: RS-232C/422/485 D-sub 9-pin: RS-232C/422/485

Communication I/F (with “DU-10” or “DUN-10” attached)
Modular jack 8-pin (2 ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/422/485 *3

Power supply 24 VDC 24 VDC

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable and attaching “DU-10” or “DUN-10”, use Hakko Electronics’ conversion cable “D9-D25”.
When not attaching “DU-10” nor “DUN-10” (except for connection with a Mitsubishi A series CPU), use Hakko Electronics’ conversion cable “MJ2-PLC”. For connection with a Mitsubishi A
series CPU, use “V706-ACPU”.
*2 Two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*3 The MJ2 port can be used for connection via RS-422 (4-wire connection).
*4 When a V6-specific optional SRAM cassette “V6EM/RSi” is in use, replace with V806iTD or V806iTDN.
*5 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V806(i)TDN. Use “CUN-xx” instead.
*6 When using the D-sub 9-pin connector on the V806, use “DU-10” for V806(i)TD and “DUN-10” for V806(i)TDN.

9
- Recommended models for replacement of V606i series (2)
V606iC series Recommended models for replacement

V606iC10 V606iC10M V806CD/V806CDN *4

MONITOUCH

+0.5 +0.5
-0 -0
174 174

Panel cut-out
dimensions

131

131
(mm)
-0
+0.5

-0
+0.5
Display device STN color STN color

Colors 16 colors 65,536 colors

Resolution 320  240 dots 320  240 dots

Touch switch Analog Matrix Analog

D-sub 25-pin: RS-232C/422/485 D-sub 9-pin: RS-232C/422/485

Communication I/F (with “DU-10” or “DUN-10” attached)
Modular jack 8-pin (2 ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/422/485 *3

Power supply 24 VDC 24 VDC

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable and attaching “DU-10” or “DUN-10”, use Hakko Electronics’ conversion cable “D9-D25”.
When not attaching “DU-10” nor “DUN-10” (except for connection with a Mitsubishi A series CPU), use Hakko Electronics’ conversion cable “MJ2-PLC”. For connection with a Mitsubishi
A series CPU, use “V706-ACPU”.
*2 Two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*3 The MJ2 port can be used for connection via RS-422 (4-wire connection).
*4 When a V6-specific optional SRAM cassette “V6EM/RSi” is in use, replace with V806iCD or V806iCDN.
*5 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V806(i)CDN. Use “CUN-xx” instead.
*6 When using the D-sub 9-pin connector on the V806, use “DU-10” for V806(i)CD and “DUN-10” for V806(i)CDN.

V606iM series Recommended models for replacement

V606iM10 V606iM10M V806MD/V806MDN *4

MONITOUCH

+0.5 +0.5
-0 -0
174 174

Panel cut-out
dimensions
131

131

(mm)
-0
+0.5

-0
+0.5

Display device STN monochrome STN monochrome

Colors 8-level grayscale 16-level grayscale

Resolution 320  240 dots 320  240 dots

Touch switch Analog Matrix Analog

D-sub 25-pin: RS-232C/422/485 D-sub 9-pin: RS-232C/422/485

Communication I/F (with “DU-10” or “DUN-10” attached)
Modular jack 8-pin (2 ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/422/485 *3
Power supply 24 VDC 24 VDC
*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable and attaching “DU-10” or “DUN-10”, use Hakko Electronics’ conversion cable “D9-D25”.
When not attaching “DU-10” nor “DUN-10” (except for connection with a Mitsubishi A series CPU), use Hakko Electronics’ conversion cable “MJ2-PLC”. For connection with a Mitsubishi A
series CPU, use “V706-ACPU”.
*2 Two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*3 The MJ2 port can be used for connection via RS-422 (4-wire connection).
*4 When a V6-specific optional SRAM cassette “V6EM/RSi” is in use, replace with V806iMD or V806iMDN.
*5 When Hakko Electronics’ communication I/F unit “CU-xx” is currently used, it cannot be attached to V806(i)MDN. Use “CUN-xx” instead.
*6 When using the D-sub 9-pin connector on the V806, use “DU-10” for V806(i)MD and “DUN-10” for V806(i)MDN.

10
- Recommended models for replacement of V606 series (1)
V606C series Recommended models for replacement

V606C10 V606C10M V806CD/V806CDN

MONITOUCH

+0.5 +0.5
174 -0 174 -0

Panel cut-out
dimensions

131

131
(mm)
-0
+0.5

-0
+0.5
Display device STN color STN color

Colors 16 colors 65,536 colors

Resolution 320  240 dots 320  240 dots

Touch switch Analog Matrix Analog

D-sub 25-pin: RS-232C/422/485 D-sub 9-pin: RS-232C/422/485

Communication I/F (with “DU-10” or “DUN-10” attached)
Modular jack 8-pin (2 ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/422/485 *3

Power supply 24 VDC 24 VDC

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable and attaching “DU-10” or “DUN-10”, use Hakko Electronics’ conversion cable “D9-D25”.
When not attaching “DU-10” nor “DUN-10” (except for connection with a Mitsubishi A series CPU), use Hakko Electronics’ conversion cable “MJ2-PLC”. For connection with a Mitsubishi
A series CPU, use “V706-ACPU”.
*2 Two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*3 The MJ2 port can be used for connection via RS-422 (4-wire connection).
*4 When Hakko Electronics’ communication I/F unit “CUS-xx” is currently used, it cannot be attached to V806CD or V806CDN. Use “CU-xx” for V806CD and “CUN-XX” for V806CDN
instead.
*5 When using the D-sub 9-pin connector on the V806, use “DU-10” for V806CD and “DUN-10” for V806CDN.

V606M series Recommended models for replacement

V606M10 V606M10M V806MD/V806MDN

MONITOUCH

+0.5 +0.5
174 -0 174 -0

Panel cut-out
dimensions
131

131

(mm)
-0
+0.5

-0
+0.5

Display device STN monochrome STN monochrome

Colors 8-level grayscale 16-level grayscale

Resolution 320  240 dots 320  240 dots

Touch switch Analog Matrix Analog

D-sub 25-pin: RS-232C/422/485 D-sub 9-pin: RS-232C/422/485

Communication I/F (with “DU-10” or “DUN-10” attached)
Modular jack 8-pin (2 ports): RS-232C/485 Modular jack 8-pin (2 ports): RS-232C/422/485 *3

Power supply 24 VDC 24 VDC

*1 Use a V8-specific cable as a PLC connection cable. When using the existing cable and attaching “DU-10” or “DUN-10”, use Hakko Electronics’ conversion cable “D9-D25”.
When not attaching “DU-10” nor “DUN-10” (except for connection with a Mitsubishi A series CPU), use Hakko Electronics’ conversion cable “MJ2-PLC”. For connection with a Mitsubishi A
series CPU, use “V706-ACPU”.
*2 Two points on the screen cannot be pressed simultaneously. For two-point pressing, use a switch on the screen and a function switch.
*3 The MJ2 port can be used for connection via RS-422 (4-wire connection).
*4 When Hakko Electronics’ communication I/F unit “CUS-xx” is currently used, it cannot be attached to V806MD or V806CDN. Use “CU-xx” for V806MD and “CUN-xx” for V806CDN.
*5 When using the D-sub 9-pin connector on the V806, use “DU-10” for V806MD and “DUN-10” for V806MDN.

11
- Screen program transfer
- V6 series [Screen configuration software]
V-SFT-5 (Ver. 5)
Windows 98SE / NT4.0 / Me / 2000 /
Modular jack
V-CP (RS-232C)
D-sub XP / XP 64 Edition /
8-pin 9-pin Vista (32bit, 64bit) / 7 (32bit, 64bit) /
8 (32bit, 64bit) / 8.1 (32bit, 64bit) /
10 (32bit, 64bit)

- V8 series [Screen configuration software]

V-SFT-5 (Ver. 5)
Windows 98SE / NT4.0 / Me / 2000 /
USB cable XP / XP 64 Edition /
USB-B USB-A
Vista (32bit, 64bit) / 7 (32bit, 64bit) /
8 (32bit, 64bit) / 8.1 (32bit, 64bit) /
10 (32bit, 64bit)
V-SFT-6 (Ver. 6)
Modular jack
V-CP (RS-232C)
D-sub Windows XP / XP 64 Edition /
8-pin 9-pin Vista (32bit, 64bit) / 7 (32bit, 64bit) /
8 (32bit, 64bit) / 8.1 (32bit, 64bit) /
10 (32bit, 64bit)
* Screen programs can also be transferred via Ethernet.

- Screen program conversion

The V6 series can be replaced with the V8 series by converting the V6 series screen program using V-SFT-5 or V-SFT-6
(V series screen configuration software).
When converting the screen program, click [System Setting]  [Edit Model Selection] on V-SFT-5 or V-SFT-6 and select a
model to be replaced with.
However, note that 100% compatibility is not ensured and some functions may be limited or may not be available after
replacement.
For details, refer to the V8 Series File Conversion Manual.

* The indicated recommended model for replacement can be used with minimal restrictions. Please note that other models not described here can also be used; make a selection
according to your system requirements.

Overseas Sales Dept.

TEL: +81-76-274-2144 FAX: +81-76-274-5136
https://monitouch.fujielectric.com/
9114NE0