Authorised Distributors:-

Intech Automation, Chennai-600 032

Phone: 43534888 Mob: 9940538888 Fax: 43534889
E-mail: [email protected] Website: www.intechautomation.in
Operation altitude < 2,000m Note: SUB1 and SUB2 do not support DTE20L and DTE20C. Please install the optional output modules you purchase into
Ambient humidity 35% to 85% RH (non-condensing) the correct slot.

Pollution degree 2 Communication Address of Output & How to Set up Parameters:

See Table 2 for the communication addresses of output and Table 3 for the definition of the value in the address.
Product Profile & Outline INA INB
Series Temperature Controller CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

OUT1, OUT2 H10A8 H10A9 H10AA H10AB H10AC H10AD H10AE H10AF
Instruction Sheet SUB1, SUB2 H10B0 H10B1 H10B2 H10B3 H10B4 H10B5 H10B6 H10B7
Thank you very much for choosing Delta DTE series temperature controller. Please read this instruction sheet carefully before DTE10T/P
using your DTE to ensure proper operation. Keep this instruction sheet handy for quick reference. 1 I/O terminals Table 2

2 Status LED Value = 0 Value = 1 Value = 2 Value = 3

Warning 3 Display and setup unit
OUT1, OUT2** Heating control Cooling control Proportional output Disable output
DANGER! CAUTION! ELECTRIC SHOCK! 4 DIN rail clip
5 Power input port SUB1, SUB2** Heating control Cooling control Alarm output* Disable output
DTE is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust,
humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from 6 RS-485 communication port Table 3
operating the device (e.g. key or specific tools are required for opening the enclosure) in case danger and
damage on the device may occur. 7 Extension module fixing clip *When there are only 4 channels of inputs, SUB1 cannot be used for alarm output but heating/cooling control only.
8 Extension port
1. Prevent dust or metallic debris from falling into the device and cause malfunctions. DO NOT modify or uninstall the circuit **When there are only 4 channels of inputs, OUT2 and SUB2 cannot be set up by the user but set up automatically as "alarm
board of DTE without being permitted. DO NOT use empty terminals. output” by the controller.
2. Keep away from high-voltage and high-frequency environment during the installation in case of interference. Prevent using Control Output:
the device in premises which contain:
DTE offers PID control, ON/OFF control, manual control and programmable PID control. Control output methods are set at
(a) dust or corrosive gas; (b) high humidity and high radiation; (c) shock and vibration.
3. The power has to be switched off when wiring or changing the temperature sensor.
Panel Layout address H10B8 ~ H10BF (default = 0: PID), PID parameters at H1028 ~ H105F, ON/OFF parameters at H1058 ~ H106F, and
manual control parameters at H1070 ~ H107F.
4. When installing the circuit board of the accessory, please make sure the power of the main unit is switched off and insert Alarm Output:
the accessory into the correct slot on the main unit.
DTE offers 12 alarm modes. The alarm modes are set up at address H10C0 ~ H10C7, upper limits at H1080 ~ H1087 and
5. Make sure to use compensation wire which matches the thermocouple or platinum resistance when extending or
lower limits at H1088 ~ H108F.
connecting the thermocouple or platinum resistance.
6. Keep the wire as short as possible when wiring a sensor to the controller. Separate the power cable and load wire in order SV Alarm Mode Alarm Output Operation
to prevent interference and induced noise.
0 No alarm Off
7. Make sure the power cables and signal device are installed correctly before switching on the power; otherwise serious ON
Alarm output is enabled when the temperature reaches upper and lower
damage may occur.
1 limits: The alarm will be enabled when PV exceeds SV + AL-H or falls below OFF
8. DO NOT touch the terminal or repair the device when the power is on; otherwise an electric shock may occur. SV – AL-L. AL-L SV AL-H
9. Please wait for 1 minute after the power is switched off to allow the capacitor to discharge and DO NOT touch the internal ON
Alarm output will be enabled when the temperature reaches the upper limit:
wiring within this period. 2 OFF
Input The alarm will be enabled when the PV exceeds SV + AL-H. SV AL-H
10. DO NOT touch the internal terminal when DTE is either switched on or off in case you may damage the circuit. ON
The standard DTE main unit is attached with 4 channels of inputs. You can purchase additional DTE20T or DTE20P to expand Alarm output will be enabled when the temperature reaches the lower limit:
11. Please place DTE with other heating objects (e.g. power supply) within proper distance while installing DTE. the number of input channels. DTE supports maximum 8 channels of inputs which belong to group INA and group INB. Each 3 OFF
The alarm will be enabled when the PV falls below SV – AL-L.
group possesses 4 input channels. AL-L SV

Ordering Information DTE series supports the following input sensors: 4

Alarm output will be enabled when the PV is between SV + AL-H and SV –
ON
OFF
AL-L.
Input Sensor Type Register Value Range AL-L SV AL-H
Alarm output will be enabled when the temperature reaches the absolute ON
For DTE10P / DTE20P
5 value of the upper and lower limits: The alarm will be enabled when the PV OFF

Series name DTE: Delta E series temperature controller Temperature measurement resistance (Cu50) 13 -50 ~ 1 50° C exceeds AL-H or falls below AL-L. AL-L AL-H
Platinum resistance (Pt100) 12 -200 ~ 600 °C Alarm output will be enabled when the temperature reaches the absolute ON
1 Device type 1: main unit 2: accessory Platinum resistance (JPt100) 11 -2 0 ~ 400° C 6 value of the upper limit: The alarm will be enabled when the PV exceeds OFF
AL-H. AL-H
0T: 4-channel TC For DTE10T / DTE20T ON
Alarm output will be enabled when the temperature reaches the absolute
0P: 4-channel PT Thermocouple TXK type 10 -2 0 0 ~ 80 0 °C 7 value of the lower limit: The alarm will be enabled when the PV falls below OFF
0V: 4 channels of voltage pulse output Thermocouple U type 9 - 20 0 ~ 5 00 ° C AL-L. AL-L

0C: 4 channels of linear current output Thermocouple L type 8 -2 00 ~ 8 50 ° C ON

0T: 4-channel TC Upper/lower limit standby alarm: The alarm will be enabled when the PV
2 3 8 OFF
0P: 4-channel PT 0R: 4 channels of relay output Thermocouple B type 7 10 0 ~ 1,8 00° C reaches SV and further exceeds SV + AL-H or falls below SV – AL-L.
AL-L SV AL-H
0L: 4 channels of linear voltage output Thermocouple S type 6 0 ~ 1 , 70 0 ° C ON
CT: 4 channels of current transformer sensors Upper limit standby alarm: The alarm will be enabled when the PV reaches
Thermocouple R type 5 0 ~ 1 , 7 00 ° C 9 OFF
DS: Display and setup module SV and further exceeds SV + AL-H.
Thermocouple N type 4 -2 00 ~ 1, 3 0 0 ° C SV AL-H
ON
Thermocouple E type 3 0 ~ 6 0 0 °C Lower limit standby alarm: The alarm will be enabled when the PV reaches
10 OFF
Functions & Electrical Specifications Thermocouple T type 2 - 20 0 ~ 4 0 0 ° C SV and further falls below SV – AL-L.
AL-L SV
Thermocouple J type 1 - 1 0 0 ~ 1, 2 0 0 ° C ON
Power input DC 24V, isolated switching power supply Upper limit hysteresis alarm: The alarm will be enabled when the PV exceeds
Thermocouple K type 0 - 2 00 ~ 1, 300 ° C 11 OFF
Voltage range 90% ~ 110% rated voltage SV + AL-H. The alarm will be disabled when the PV falls below SV + AL-L. AL-L AL-H
Power consumption Max. 10W + 3W × number of DTC2000 controllers connected in parallel (Max. 7) Note: The default setting in DTE10T is “thermocouple K type”. The default setting in DTE10P is “Pt100".
Lower limit hysteresis alarm: The alarm will be enabled when the PV falls ON

Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK Communication address: Input sensor types at H10A0 ~ H10A7; input upper limits at H1010 ~ H1017; input lower limits at 12 below SV – AL-H. The alarm will be disabled when the PV exceeds SV – OFF
Input sensor H1018 ~ H101F. AL-L. AL-H AL-L
Platinum resistance: Pt100, JPt100, Cu50
Sampling cycle Thermocouple or platinum resistance: 1.0 second/all input Output LED Display
Control method PID, PID programmable, manual, ON/OFF DTE supports maximum 16 channels of outputs, belonging to output groups OUT1, OUT2, SUB1 and SUB2, each group with 4 PWR: On DTE is powered.
Relay output: SPST, Max. AC 250V load, 3A resistive load channels. See the explanations below for how input channels correspond to output groups.
RUN: On Any of the channel is executing.
Output accessories Voltage pulse output: DC 24V, Max. 40mA current output Without group INB (4 channels of input): Every channel corresponds to 2 groups of output and 2 groups of alarms. OUT1 and
SUB1 are for control output, and OUT1 can be used for proportional output. OUT2 and SUB2 are fixed for alarm output. COM: Flashing Communication in progress
(optional) Current output: DC 4 ~ 20mA output (resistive load < 500Ÿ); for OUT1 and OUT2 only
With group INB (8 channels of input): Every channel is paired with 2 groups of outputs. OUT1 and OUT2 are used for control ERR: Indicating errors (red)
Analog voltage output: 0 ~ 10V (resistive load > 1,000Ÿ); for OUT1 and OUT2 only output or proportional output of CH1 ~ CH8. SUB1 and SUB2 are used for control output or alarm output. ERR LED is on indicates one of the following errors occur, and the output has to be disabled.
Control output, alarm output or proportional output (proportional output is only applicable in See Table 1 for the relations between input and output.
Output functions 1. Memory EEPROM error.
the model with linear voltage and current output for OUT1, OUT2)
4 channels of input 8 channels of input 2. Any of the input points is not connected.
Alarm modes 12 alarm modes available
3. Any of the input points exceeds the setup range.
Communication RS-485 digital communication; supports baud rate 2,400bps ~ 115,200bps Output Group INA (CH1 ~ CH4) INA (CH1 ~ CH4) INB (CH5 ~ CH8)
4. Any of the input temperatures has not been stabilized.
Communication Main control output or Main control output or proportional
Supports Modbus ASCII/RTU OUT1 No corresponding output
protocol proportional output output
The extension port transmits 24V power supply and communication signals to extension
Synchronous Communication Protocol & Auto ID Setup
Extension port Main control output or proportional
module DTC2000. OUT2 Alarm 1 output No corresponding output This function allows the auto setup of communication protocol in extension module DTC2000 and DTC2001 following the
output
2 communication protocol set in the DTE main unit. The station IDs of DTC decrease. See below for the steps.
Vibration resistance 10 ~ 55Hz 10m/s 3 axes 10mins SUB1 Control output Control output or alarm output No corresponding output
2 1. Set the auto communication ID of DTE as “1” (communication address: H10F8).
Shock resistance Max. 300m/s 3 axes 6 directions, 3 times each SUB2 Alarm 2 output No corresponding output Control output or alarm output
2. Switch off DTE. Connect DTE with extension module DTC2000, DTC2001 and switch on DTE again.
Ambient temperature 0°C ~ +50°C Table 1 3. Default communication protocol: 9,600bps, 7 bits, Even, 1 stop bit, communication address = 01.
Storage temperature -20°C ~ +65°C
4. This function will consume 3 ~ 5 seconds more when you switch on DTE.
INA INB Read Command Read Response Message Write Command Write Response Message

56 Communication Content Explanation CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 ‘1’ Length of response data ‘ 0’ ‘1’ ‘ 1’
‘0’ (byte) ‘4’ ‘ 0’ ‘0’
0: stop Read start address of
1. DTE supports baud rates 2,400/4,800/9,600/19,200/38,400/57,600/115,200 bps and does not support communication Data address Data address
Run/Stop the 1: executing H10D8 H10D9 H10DA H10DB H10DC H10DD H10DE H10DF data/bit ‘0’ ‘ 0’ ‘0’ ‘ 0’
format 7, N, 1/8, E, 2/8, O, 2. Communication protocol = Modbus ASCII or RTU.
control 2: program stops (H111B) (H121B) (H131B) (H141B) (H151B) (H161B) (H171B) (H181B) ‘0’ ‘ 1’ ‘1’ ‘1’
2. Function codes: H03 = read maximum 8 words in the register; H06 = write 1 word into the register.
3: program pauses Data content in H1000
3. Address and contents: Every parameter has 2 communication addresses. One is numbered by the function of the ‘0’ ‘F’ ‘0’ ‘ 0’
Status of PID 0: stop H10E0 H10E1 H10E2 H10E3 H10E4 H10E5 H10E6 H10E7
parameter, and the other is by the order of channel (as shown in the table below). ‘0’ ‘4’ ‘ 3’ ‘3’
DXWRWXQLQJ 1: executing (H111C) (H121C) (H131C) (H141C) (H151C) (H161C) (H171C) (H181C) Read length of data/bit
Write data content Write data content
(word/bit) ‘0’ ‘ 0’ ‘E’ ‘ E’
INA INB Positive/negative
0: positive H10E8 H10E9 H10EA H10EB H10EC H10ED H10EE H10EF
proportional ‘2’ ‘ 0’ ‘8’ ‘8’
Content Explanation CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 1: negative (slope) (H111D) (H121D) (H131D) (H141D) (H151D) (H161D) (H171D) (H181D) Data content in H1001
output
LRC1 check ‘E’ ‘ 0’ LRC1 check ‘F’ LR C 1 c h e c k ‘F’
Present H10F1 H10F2
H10F0 LRC0 check ‘A’ ‘0’ LRC0 check ‘D’ LRC0 check ‘D’
temperature Unit; 0.1 H1000 H1001 H1002 H1003 H1004 H1005 H1006 H1007 Other statuses Other statuses
Open special Return to H10F3 H10F4 H10F5 H10F6 H10F7
Temperature function
value/input error See Table 5 (H1100) (H1200) (H1300) (H1400) (H1500) (H1600) (H1700) (H1800) unit
default Reserved Reserved Reserved Reserved Reserved End word 1 CR LRC1 check ‘0’ End word 1 CR End word 1 CR
code (H1234) (H1357)
End word 0 LF LRC0 check ‘3’ End word 0 LF End word 0 LF
Set temperature H1008 H1009 H100A H100B H100C H100D H100E H100F H10F8 H10FB H10FC H10FD H10FF
Communication H10F9 H10FA H10FE End word 1 CR
Unit: 0.1 See Table 4 Auto ID ASCII = 0 8 bits=0 2 stop=0 Address
value (H1101) (H1201) (H1301) (H1401) (H1501) (H1601) (H1701) (H1801) specifications setup
Reserved Baud rate
RTU = 1
Parity
7 bits=1 1 stop=1 1 ~ 247 End word 0 LF
Max. temperature Disabled when higher H1010 H1011 H1012 H1013 H1014 H1015 H1016 H1017
LRC Check:
value than default value (H1102) (H1202) (H1302) (H1402) (H1502) (H1602) (H1702) (H1802) Communication Parameter Setting:
Sum up the contents from “machine address” to “data content”, e.g.++H1++ H02 = H16. Obtain
Min. temperature Disabled when lower H1018 H1019 H101A H101B H101C H101D H101E H101F Content 0 1 2 3 4 5 6 2’scomplement H EA.
value than default value (H1103) (H1203) (H1303) (H1403) (H1503) (H1603) (H1703) (H1803)
Baud rate 2,400bps 4,800bps 9,600bps 19,200bps 38,400bps 57,600bps 115,200bps RTU Mode:
Error temperature a H1020 H1021 H1022 H1023 H1024 H1025 H1026 H1027
Parity bit None (N) Even (E) Odd (O)
value Unit: 0.1°C (H1104) (H1204) (H1304) (H1404) (H1504) (H1604) (H1704) (H1804) Read Command Read Response Message Write Command Write Response Message
Proportional band 0 ~ 9,999 H1028 H1029 H102A H102B H102C H102D H102E H102F Table 4 Machine address H01 Machine address H01 Machine address H01 Machine address H01
value (Pb) Unit: 0.1 (H1105) (H1205) (H1305) (H1405) (H1505) (H1605) (H1705) (H1805)
Error Codes: Command H03 Command H03 Command H06 Command H06
H1030 H1031 H1032 H1033 H1034 H1035 H1036 H1037
Ti value 0 ~ 9,999 The error codes can be read from address H1000 ~ H1007. When the input operation is in normal status, H1000 ~ H1007 are Read start address of H10 Length of response H10 H10
(H1106) (H1206) (H1306) (H1406) (H1506) (H1606) (H1706) (H1806) H04 Write data address Write data address
for input values. When input error occurs (except for stable status and input exceeding the range), DTE will read error codes data H00 data (byte) H01 H01
H1038 H1039 H103A H103B H103C H103D H103E H103F in H8001 ~ H8002.
Td value 0 ~ 9,999 Read length of data H00 H01 H 03 H03
(H1107) (H1207) (H1307) (H1407) (H1507) (H1607) (H1707) (H1807) Data content 1 Write data content Write data content
(bit/word) H02 HF4 H20 H20
0.0 ~ 100.0% H1040 H1041 H1042 H1043 H1044 H1045 H1046 H1010
Integration default H1000 Error description
Unit: 0.1% (H1108) (H1208) (H1308) (H1408) (H1508) (H1608) (H1708) (H1808) CRC low byte HC0 H03 CRC low byte HD D CRC low byte HDD
H8001 EEPROM cannot be written in. Data content 2
Proportional control CRC high byte HCB H20 CRC high byte HE2 CRC high byte HE2
0.0 ~ 100.0% H1048 H1049 H104A H104B H104C H104D H104E H104F H8002 Input sensor is not connected.
offset error value, CRC low byte HBB
Unit: 0.1% (H1109) (H1209) (H1309) (H1409) (H1509) (H1609) (H1709) (H1809)
when Ti = 0 H8003 Group INB is not connected.
CRC high byte H 15
Proportional band H1050 H1051 H1052 H1053 H1054 H1055 H1056 H1057
0.01 ~ 99.99 Table 5
coefficient of output
Unit: 0.01 (H110A) (H120A) (H130A) (H140A) (H150A) (H160A) (H170A) (H180A) CRC (Cyclical Redundancy Check) is obtained by the following steps:
1 and output 2 Analog output current tuning scale: 1μ A/scale
unsigned int reg_crc = 0xffff;
Dead band of H1058 H1059 H105A H105B H105C H105D H105E H105F Analog output voltage tuning scale: 1mV/scale i = 0;
control output 1 & a Returning to Default Value: Write H1234 into address H10F1 and H1357 into address H10F2. Restart DTE. while (length)
output 2. (H110B) (H120B) (H130B) (H140B) (H150B) (H160B) (H170B) (H180B)
{ reg_crc ^= RTUData[i];
Hysteresis for 0 ~ 9,999 H1060 H1061 H1062 H1063 H1064 H1065 H1066 H1067 Programmable Communication Parameter Setting: i ++;
output 1 Unit: 0.1% (H110C) (H120C) (H130C) (H140C) (H150C) (H160C) (H170C) (H180C) for (j = 0; j < 8; j++)
{ if (reg_crc & 0x01) reg_crc = (reg_crc >> 1) ^ 0xA001;
H1068 H1069 H106A H106B H106C H106D H106E H106F INA INB
Hysteresis for 0 ~ 9,999 else reg_crc = reg_crc >> 1;
output 2 Unit: 0.1% (H110D) (H120D) (H130D) (H140D) (H150D) (H160D) (H170D) (H180D) }
Content Explanation CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
}
Read/write output H1070 H1071 H1072 H1073 H1074 H1075 H1076 H1077 return(reg_crc);
Unit: 0.1 % Read remaining time of the step Unit: sec H111E H121E H131E H141E H151E H161E H171E H181E
1 value (H110E) (H120E) (H130E) (H140E) (H150E) (H160E) (H170E) (H180E)
H1078 H1079 H107A H107B H107C H107D H107E H107F Read remaining time of the step Unit: min H111F H121F H131F H141F H151F H161F H171F H181F Software for Setting up Communication on PC: Download the free software on Delta’s website.
Read/write output
Unit: 0.1 % Read the NO. of the current
2 value (H110F) (H120F) (H130F) (H140F) (H150F) (H160F) (H170F) (H180F) 0~7 H1120 H1220 H1320 H1420 H1520 H1620 H1720 H1820
pattern
Upper limit for
Alarm enabled H1080 H1081 H1082 H1083 H1084 H1085 H1086 H1087 How to Mount & DIN Rail Size
when temperature Read the NO. of the current step 0~7 H1121 H1221 H1321 H1421 H1521 H1621 H1721 H1821
alarm output (H1110) (1210) (H1310) (H1410) (H1510) (H1610) (H1710) (H1810)
exceeds upper limit NO. of start pattern 0~7 H1122 H1222 H1322 H1422 H1522 H1622 H1722 H1822
Alarm enabled NO. of start step 0~7 H1123 H1223 H1323 H1423 H1523 H1623 H1723 H1823
Lower limit for when temperature H1088 H1089 H108A H108B H108C H108D H108E H108F
alarm output falls below lower (H1111) (H1211) (H1311) (H1411) (H1511) (H1611) (H1711) (H1811) Programmable Parameter Setting:
limit
Tuning for upper Current (4 ~ 20mA) Pattern Pattern Pattern Pattern Pattern Pattern Pattern Pattern
H1090 H1091 H1092 H1093 H1094 H1095 H1096 H1097 Content Explanation
limit of analog or voltage output 0 1 2 3 4 5 6 7
output tuning (H1112) (H1212) (H1312) (H1412) (H1512) (H1612) (H1712) (H1812) 0 ~ 7 = N: The pattern
Max. number of
executes from step 0 to H2068 H2069 H206A H206B H206C H206D H206E H206F
Tuning for lower Current (4 ~ 20mA) H1098 H1099 H109A H109B H109C H109D H109E H109F steps in the pattern
N.
limit of analog or voltage output
output tuning (H1113) (H1213) (H1313) (H1413) (H1513) (H1613) (H1713) (H1813) Number of cycles of 0 ~ 199: The pattern Connect maximum 7 DTC2000 or DTC2001 controllers to DTE by using DIN rail.
pattern 0 ~ 7 has been executed for 1 H2070 H2071 H2072 H2073 H2074 H2075 H2076 H2077
H10A0 H10A1 H10A2 H10A3 H10A4 H10A5 H10A6 H10A7
Input sensor type See “Input” section execution ~ 200 times
(H1114) (H1214) (H1314) (H1414) (H1514) (H1614) (H1714) (H1814)
0 ~ 8: 8 refers to end of
0: heating NO. of current link
program; 0 ~ 7 refer to H2078 H2079 H207A H207B H207C H207D H207E H207F
Output function 1: cooling H10A8 H10A9 H10AA H10AB H10AC H10AD H10AE H10AF pattern
the NO. of next pattern
for output 1 2: proportional (H1115) (H1215) (H1315) (H1415) (H1515) (H1615) (H1715) (H1815)
output
0: heating (default) Address Default Content Explanation
Output function H10B0 H10B1 H10B2 H10B3 H10B4 H10B5 H10B6 H10B7
1: cooling
for output 2 (H1116) (H1216) (H1316) (H1416) (H1516) (H1616) (H1716) (H1816) Target temperatures for pattern 0 ~ 7
2: alarm 2000H ~ 203FH 0 Unit: 0.1°C
Pattern 0: 2000H ~ 2007H
0: PID
1: ONOFF Execution time for pattern 0 ~ 7
H10B8 H10B9 H10BA H10BB H10BC H10BD H10BE H10BF 2080H ~ 20BFH 0 Time: 0 ~ 900 (Unit: 1 min)
Control method 2: manual Pattern 0: 2080H ~ 2087H
3: PID (H1117) (H1217) (H1317) (H1417) (H1517) (H1617) (H1717) (H1817)
The content of this instruction sheet may be revised without prior notice. Please consult our distributor or
programmable 4. Communication format: H03 = read bit data; H06 = write bit data download the most updated version at http://www.delta.com.tw/industrialautomation.

Alarm 1 output See “Alarm Output” H10C0 H10C1 H10C2 H10C3 H10C4 H10C5 H10C6 H10C7 ASCII Mode:
mode section (H1118) (H1218) (H1318) (H1418) (H1518) (H1618) (H1718) (H1818)
H10C4 H10C5 H10C6 H10C7 Read Command Read Response Message Write Command Write Response Message
Alarm 2 output See “Alarm Output”
mode section (H1518) (H1618) (H1718) (H1818) Start word ’:’ Start word ’:’ Start word ’:’ Start word ’:’ $XWKRULVHG'LVWULEXWRUV
Heating/cooling 1 ~ 99 seconds H10C8 H10C9 H10CA H10CB H10CC H10CD H10CE H10CF Machine address 1 ‘0’ Machine address 1 ‘0’ Machine address 1 ‘0’ Machine address 1 ‘0’ Intech Automation
cycle for output 1 0 = 0.5 second (H1119) (H1219) (H1319) (H1419) (H1519) (H1619) (H1719) (H1819) Machine address 0 ‘1’ Machine address 0 ‘1’ Machine address 0 ‘1’ Machine address 0 ‘1’ QG)ORRU67KLUX9L.D,QGXVWULDO(VWDWH*XLQG\&KHQQDL
Heating/cooling 1 ~ 99 seconds H10D0 H10D1 H10D2 H10D3 H10D4 H10D5 H10D6 H10D7 Command 1 ‘0’ Command 1 ‘0’ Command 1 ‘0’ Command 1 ‘0’
cycle for output 2 0 = 0.5 second (H111A) (H121A) (H131A) (H141A) (H151A) (H161A) (H171A) (H181A) 3KRQH0RE)D[
Command 0 ‘3’ Command 0 ‘3’ Command 0 ‘6’ Command 0 ‘6’
(PDLOLQIR#LQWHFKDXWRPDWLRQLQ:HEVLWHZZZLQWHFKDXWRPDWLRQLQ