B Nfvis Command Ref
Uploaded by
lakbabi1035B Nfvis Command Ref
Uploaded by
lakbabi1035Cisco Enterprise Network Function Virtualization Infrastructure
Software Command Reference
First Published: 2017-04-07
Last Modified: 2024-01-19
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
© 2017–2023 Cisco Systems, Inc. All rights reserved.
CONTENTS
CHAPTER 1 Banner and Message Commands 1
banner-motd 2
show banner-motd 3
show running-config banner-motd 4
CHAPTER 2 Cisco NFVIS Smart Licensing Commands 5
show running config pnic 6
show nic 7
show license 8
Action Commands 9
CHAPTER 3 System and IP Configuration Commands 11
system settings default-gw 12
system settings disk-space threshold 13
system settings hostname 14
system settings ip-receive-acl 15
show running-config system settings ip-receive-acl 17
system settings mgmt 18
system settings wan 19
system storage 20
show system settings 21
show system settings-native 22
show system top 24
show system disk-space 25
show system file-handles 26
show system processes 27
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
iii
Contents
show system services 28
show system status 29
show platform-detail 30
show version 31
show free-memory 32
show certificate 33
show file 34
show cores 35
show nfv_mode 36
CHAPTER 4 PnP Commands 37
pnp action 38
pnp automatic 39
pnp static 41
show pnp 42
CHAPTER 5 Resource Commands 43
show resources cpu-info allocation 44
show resources cpu-info cpus 45
CHAPTER 6 Networks and Bridges Commands 47
networks network 48
bridge 51
bridges bridge 52
show running-config bridges 53
show system networks 54
show system packages 55
ping 56
ping-ipv6 57
traceroute 58
CHAPTER 7 VM Lifecycle Management Commands 59
vm_lifecycle flavors 60
vm_lifecycle images 61
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
iv
Contents
vm_lifecycle tenants tenant admin deployments 65
vmAction 69
vmBackupAction 70
vmConsole 71
vncconsole start 72
show vm_lifecycle opdata 73
show running-config vm_lifecycle 76
show running-config vm_packages 77
CHAPTER 8 Internal Management IP Commands 79
vm_lifecycle networks 80
CHAPTER 9 System Monitoring Commands 81
hostaction mgmt-dhcp-renew 82
hostaction wan-dhcp-renew 83
hostaction reboot 84
hostaction shutdown 85
show resources cpu-info allocation 86
show resources cpu-info cpus 87
show resources cpu-info vnfs 88
show resources precheck vnf 89
show system-monitoring host cpu 90
show system-monitoring host disk 92
show system-monitoring host memory 94
show system-monitoring host port 96
show system-monitoring vnf vcpu 98
show system-monitoring vnf disk 99
show system-monitoring vnf memory 101
show system-monitoring vnf port 103
CHAPTER 10 System Operations Commands 105
scp 106
system file-copy usb 109
system file-download file 110
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
v
Contents
system file-delete 111
system usb-mount 112
telnet 113
show system file-list 114
CHAPTER 11 System Time Commands 115
system time 116
system set-manual-time 118
show system time 119
show running-config system time 120
CHAPTER 12 System Portal Commands 121
system portal access 122
show system portal status 123
show running-config system portal access 124
CHAPTER 13 System Routes Commands 125
system routes route 126
show system routes 127
show system dhcp-routes 128
show running-config system routes 129
CHAPTER 14 System Log Commands 131
system set-log 132
show system logging-level 133
show log 134
CHAPTER 15 Span Session and Packet Capture Commands 137
source 138
destination 139
show system monitor session 140
monitor session 141
tcpdump port 142
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
vi
Contents
tcpdump vnic 143
CHAPTER 16 Upgrade Package Commands 145
show system upgrade apply-image 146
show system upgrade reg-info 147
system upgrade apply-image 148
system upgrade image-name 149
CHAPTER 17 Factory Default Reset Command 151
factory-default-reset 152
CHAPTER 18 Syslog Commands 153
system settings logging host 154
system settings logging facility 155
system settings logging severity 156
show running-config system settings logging 157
CHAPTER 19 SNMP Commands 159
snmp agent engineID 160
snmp agent sysName 161
snmp community 162
snmp enable traps 163
snmp disable traps 164
snmp group 165
snmp host 166
snmp user 167
show snmp agent 168
show snmp stats 169
show snmp traps 170
show running-config snmp 171
CHAPTER 20 RADIUS Commands 173
radius-server host 174
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
vii
Contents
show running-config radius-server 175
CHAPTER 21 TACACS Commands 177
tacacs-server host 178
key 179
admin-priv 180
oper-priv 181
show running-config tacacs-server host 182
CHAPTER 22 User Management Commands 183
rbac authentication min-pwd-length 184
rbac authentication password-lifetime 185
rbac authentication account-inactivity 186
rbac authentication users 187
rbac authentication users user activate 188
rbac authentication users user change-password 189
rbac authentication users user change-role 190
show running-config rbac authentication users 191
CHAPTER 23 Secondary IP and Source Interface Commands 193
system settings wan secondary 194
system settings source-interface 195
CHAPTER 24 Ports and Port Channel Commands 197
hostaction pnic-breakout 198
hostaction pnic-breakout force 199
pnic 200
show nic 202
show pnic 203
show pnic-breakout 205
show port-channel 206
show lldp stats 207
show lldp neighbors 208
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
viii
Contents
CHAPTER 25 Secure Overlay and BGP Commands 209
show secure-overlay 210
show bgp vpnv4 unicast 211
show bgp vpnv4 unicast route 212
show bgp vpnv4 unicast summary 213
CHAPTER 26 Storage Virtualization Commands 215
cluster datastore intdatastore 216
cluster migrate-deployment 217
CHAPTER 27 Support Commands 219
support show arp 221
support show bgp 222
support show bgp route 223
support show config-drive 224
support show config-drive content 225
support show cpuinfo 226
support show date-time 227
support show df 228
support show domainname 229
support show dmidecode 230
support show ethtool 232
support show ifconfig 236
support show iostat 237
support show ipsec 238
support show loadavg 239
support show meminfo 240
support show netstattcp 242
support show netstatudp 243
support show procstat 244
support show route 246
support show snmp 247
support show system-version 248
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
ix
Contents
support show system-hostname 249
support virsh all-info 250
support virsh capabilities 253
support virsh cpu-stats 257
support virsh domiflist 258
support virsh dumpxml 259
support virsh iface-list 261
support virsh iface-dumpxml 262
support virsh list 263
support virsh memory-stats 264
support virsh net-dumpxml 265
support virsh net-list 266
support virsh net-info 267
support virsh nodecpustats 268
support virsh pool-list 269
support virsh pool-dumpxml 270
support virsh sys-info 271
support virsh vol-dumpxml 274
support virsh vol-list 275
support ovs all-info 276
support ovs appctl fdb-show 278
support ovs dpctl show 280
support ovs ofctl dump-ports 281
support ovs ofctl dump-ports-desc 282
support ovs vsctl list-br 283
support ovs vsctl list interface 284
support ovs vsctl list-ports 285
support ovs vsctl show 286
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
x
Banner and Message Commands
• banner-motd, on page 2
• show banner-motd, on page 3
• show running-config banner-motd, on page 4
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
1
Banner and Message Commands
banner-motd
banner-motd
To configure a banner and message of the day (MOTD), use the banner-motd command in global configuration
mode. To remove the banner or MOTD, use the no form of the command.
banner-motd { banner string | motd string }
no banner-motd [{ banner | motd }]
Syntax Description banner string Specifies the banner text.
motd string Specifies the MOTD text.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines To verify the configuration, use the show running-config banner-motd command. To delete both the banner
and the MOTD configuration, use the no banner-motd command without any keywords and arguments.
Example
The following example shows how to configure both the banner and the MOTD:
nfvis(config)# banner-motd banner "This is a new banner" motd "This is a new motd"
nfvis(config)# commit
nfvis(config)# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
2
Banner and Message Commands
show banner-motd
show banner-motd
To display the system-defined banner, use the show banner-motd command in privileged EXEC mode.
show banner-motd [{system-banner}]
Syntax Description system-banner The system-defined
banner.
Command Default The system-defined banner is displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Usage Guidelines This command displays only the system-defined banner. It does not display the user-defined banner or message
of the day.
Example
The following is a sample output of the show banner-motd command:
nfvis# show banner-motd
banner-motd system-banner "\nCisco Enterprise Network Function Virtualization Infrastructure
Software (NFVIS)\n\nCopyright (c) 2015-2016 by Cisco Systems, Inc.\nCisco, Cisco Systems,
and Cisco Systems logo are registered trademarks of Cisco\nSystems, Inc. and/or its
affiliates in the U.S. and certain other countries.
\n\nThe copyrights to certain works contained in this software are owned by other\nthird
parties and used and distributed under third party license agreements.\nCertain components
of this software are licensed under the GNU GPL 2.0, GPL 3.0,\nLGPL 2.1, LGPL 3.0 and AGPL
3.0.\n\n\n"
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
3
Banner and Message Commands
show running-config banner-motd
show running-config banner-motd
To display the configured banner and MOTD, use the show running-config banner-motd command in
privileged EXEC mode.
show running-config banner-motd [{banner | motd}]
Syntax Description banner (Optional) Specifies to display only banner information.
motd (Optional) Specifies to display only MOTD information.
Command Default Information about configured banner and MOTD is displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following is a sample output of the show running-config banner-motd command:
nfvis# show running-config banner-motd
banner-motd banner ExampleBanner
banner-motd motd ExampleMOTD
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
4
Cisco NFVIS Smart Licensing Commands
• show running config pnic, on page 6
• show nic, on page 7
• show license, on page 8
• Action Commands, on page 9
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
5
Cisco NFVIS Smart Licensing Commands
show running config pnic
show running config pnic
Use show running config pnic to view the default number of VFs
show running-config pnic
Syntax Description pnic The pnic
ID
Command Default The default gateway is not set.
Command Modes User Exec
Command History Release Modification
4.13.1 This command was introduced.
Example
The following command shows the number of PNICs:
nfvis# show running-config pnic
pnic GE0-0
sriov numvfs 6
!
pnic GE0-1
sriov numvfs 6
!
pnic GE1-0
sriov numvfs 4
!
pnic GE1-1
sriov numvfs 4
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
6
Cisco NFVIS Smart Licensing Commands
show nic
show nic
Use the command show nic to view more details on the NICs supported on Cisco UCS C-Series M6 rack
servers.
show nic
Syntax Description nic The NIC
ID
Command Default The default gateway is not set.
Command Modes User Exec
Command History Release Modification
4.13.1 This command was introduced.
Example
The following command shows the details of NICs:
nfvis# show running-config pnic
SLOTID ADAPTER VENDOR DEVID MODE DEVNO PNICS
---------------------------------------------------------------------------------------------------------------
1 Intel i350 Quad Port 1Gb Adapter 8086 1521 NA NA ['GE1-0', 'GE1-1',
'GE1-2', 'GE1-3']
2 Cisco-MLNX MCX623106AS-CDAT 15b3 101d NA NA []
2x100GbE QSFP56 PCIe NIC
3 Intel Network controller 8086 10fb NA NA ['GE3-0', 'GE3-1']
4 Intel X710-DA4 Quad Port 10Gb SFP+ 8086 1572 NA NA ['GE4-0', 'GE4-1',
'GE4-2', 'GE4-3']
converged NIC
5 Intel Network controller 8086 10fb NA NA ['GE5-0', 'GE5-1']
L Intel X550 LOM 8086 1563 NA NA ['GE0-0', 'GE0-1']
MLOM Cisco UCS VIC 1467 MLOM 1137 0131 NA NA []
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
7
Cisco NFVIS Smart Licensing Commands
show license
show license
Use the command show license to see more details on the Cisco smart license.
show license
Syntax Description license The license
number
Command Default The default gateway is not set.
Command Modes User Exec
Command History Release Modification
4.13.1 This command was introduced.
Example
The following command shows the details of NICs:
nfvis# show license
Description: Licensing Commands
Possible completions:
accounts Display information for the user accounts for licenses
license-units-consumed Number of license units consumed.
opdata Smart Licensing operational data information.
status Show license status information
summary Show license summary
tech Tech commands
transport Operational Data For Cisco Smart Licensing status.
udi Display the Universal Device Identifier information for the
device
usage Show license usage information
| Output modifiers
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
8
Cisco NFVIS Smart Licensing Commands
Action Commands
Action Commands
Use the following actions commands that can help you release, sync and trust Cisco NFVIS licences:
• license smart release: Use this command to send a "License Usage 0" message to CSSM. This
action prompts the CSSM to release the license entitlement associated with your Cisco UCS C M6 Rack
servers. If the device continues to operate with Cisco NFVIS after the license release, a usage report,
also known as RUM, is sent to CSSM after a predetermined time interval. This report will indicate the
actual number of license units consumed, which will then be reserved again on CSSM. Following a
license release, a notification and system logging warning is issued, urging you to cease using Cisco
NFVIS as the license has been released. You receive this notification every 8 hours during the 24 hours
after a license release. If you continue to use Cisco NFVIS beyond this 24-hour period, a RUM report
will be generated reflecting the appropriate number of license units consumed by Cisco NFVIS. This
report is sent to the Licensing server based on the set periodic interval, after which the licensing server
will reserve the correct number of license units for the device again.
• license smart sync: Report a license usage to CSSM using this action command.
• license smart trust: Initiate the establishment of trust between the device and the CSSM. This
action can prove beneficial in various scenarios, including but not limited to the following:
1. If you delete the product instance from CSSM but wish to continue with Cisco NFVIS Licensing.
2. If you transfer your licenses from one Virtual Account to another.
3. If there is an asynchrony between the licensing state on CSSM and on the device.
4. If the licensing certificates on the device reach their expiry date.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
9
Cisco NFVIS Smart Licensing Commands
Action Commands
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
10
System and IP Configuration Commands
• system settings default-gw, on page 12
• system settings disk-space threshold, on page 13
• system settings hostname, on page 14
• system settings ip-receive-acl, on page 15
• show running-config system settings ip-receive-acl, on page 17
• system settings mgmt, on page 18
• system settings wan, on page 19
• system storage, on page 20
• show system settings, on page 21
• show system settings-native, on page 22
• show system top, on page 24
• show system disk-space, on page 25
• show system file-handles, on page 26
• show system processes, on page 27
• show system services, on page 28
• show system status, on page 29
• show platform-detail, on page 30
• show version, on page 31
• show free-memory, on page 32
• show certificate, on page 33
• show file, on page 34
• show cores, on page 35
• show nfv_mode, on page 36
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
11
System and IP Configuration Commands
system settings default-gw
system settings default-gw
To configure the default gateway, use the system settings default-gw command in global configuration mode.
To delete the default gateway, use the no form of the command.
system settings default-gw ip-address
no system settings default-gw
Syntax Description ip-address The default gateway IP address
Command Default The default gateway is not set.
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines To configure DHCP either on the WAN interface or the management interface, delete the default gateway.
Example
The following command sets the default gateway:
nfvis(config)# system settings default-gw 209.165.201.1
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
12
System and IP Configuration Commands
system settings disk-space threshold
system settings disk-space threshold
To configure the threshold for disk space usage, use the system settings disk-space threshold command in
global configuration mode. To delete the configured disk space usage threshold, use the no form of the
command.
system settings disk-space threshold value
no system settings disk-space threshold
Syntax Description threshold value Specifies the threshold value in percentage for disk space usage. Valid range is from 1 to
100. When the disk space usage reaches the specified threshold, a notification is sent.
Command Default Default notification threshold is set at 90%.
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis(config)# system settings disk-space threshold 1
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
13
System and IP Configuration Commands
system settings hostname
system settings hostname
To set the hostname of the system, use the system settings hostname command in global configuration mode.
system settings hostname host-name
Syntax Description host-name The hostname of the system.
Command Default The default hostname is nfvis
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced
Example
The following command changes the hostname of the system to nfvis-demo:
nfvis(config)# set system settings hostname nfvis-demo
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
14
System and IP Configuration Commands
system settings ip-receive-acl
system settings ip-receive-acl
To configure the source network for Access Control List (ACL) access to the management interface, use the
system settings ip-receive-acl command in global configuration mode. To remove the configured source
network, use the no form of the command.
system settings ip-receive-acl source-ip-address [service {https | icmp | netconf | scpd | snmp |
ssh}] [priority priority] [action {accept | reject | drop}]
no system settings ip-receive-acl
Syntax Description source-ip-address Specifies the IPv4 IP address of the source network. When the management ACL access
is enabled, only specified source networks can access the management interface. When
no ACL rule is defined, all types of traffic is allowed. If the source network is specified
as 0.0.0.0/0, the configuration is applicable to all source networks.
service Specifies the service type for the management ACL access. Valid values are:
• https: Includes port 80, port 443 and all ports to access the service console.
• icmp: Provides ability to ping the host.
• netconf: Includes port 2022. This port is required for communication between nodes
of a cluster.
• scpd: Provides ability to run the scp command from an external system.
Note To use the port 22222, you must run the system settings ip-receive-acl
command with scpd service. Starting with release 3.7.1, the port 22222
is closed by default.
• snmp: Includes port 161 and configured NET-SNMP port.
• ssh: Includes port 22 and port 2024.
You can specify one, more than one, or all service types in this parameter. To specify
multiple service types, enter the values within the square brackets []; for example, service
[ snmp https ]. If you do not specify any specific service, the configuration is applicable
to all services.
priority priority Specifies the priority for the ACL rule. Each ACL rule must have a unique priority value.
Valid range is from 0 to 65,535. ACL rule with priority 0 has the highest priority. Whenever
an ACL rule with priority 0 is matched, Cisco Enterprise NFVIS performs the action
associated with this ACL rule and does not look up any lower priority ACL rules.
action Specifies the action for the packets received from a source network. Valid values are:
• accept: Accept the packets.
• reject: Reject the packets and return the error to the source network.
• drop: Drop packets immediately and do not send any information to the source
network.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
15
System and IP Configuration Commands
system settings ip-receive-acl
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 This command was introduced.
Example
The following example opens port 22222 for all IPs.
nfvis(config)# system settings ip-receive-acl 0.0.0.0/0 service scpd priority 2 action
accept
nfvis(config-ip-receive-acl-0.0.0.0/0)# commit
Example
The following example opens port 22222 for a specific IP.
nfvis(config)# system settings ip-receive-acl 203.0.113.1/32 service scpd priority 1 action
accept
nfvis(config-ip-receive-acl-203.0.113.1/32)# commit
Example
The following example configures the SSH service for a specific IP.
nfvis(config)# system settings ip-receive-acl 198.51.100.11/32 priority 1 service ssh action
accept
nfvis(config-ip-receive-acl-198.51.100.11/32)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
16
System and IP Configuration Commands
show running-config system settings ip-receive-acl
show running-config system settings ip-receive-acl
To display the configured source network for ACL access to the management interface, use the show
running-config system settings ip-receive-acl command in privileged EXEC mode.
show running-config system settings ip-receive-acl
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# show running-config system settings ip-receive-acl
system settings ip-receive-acl 198.51.100.11/24
service [ ssh https scpd ]
action accept
priority 100
!
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
17
System and IP Configuration Commands
system settings mgmt
system settings mgmt
To configure the management interface either with a static IP address or with DHCP, use the system settings
mgmt command in global configuration mode.
system settings mgmt {dhcp | ip address mgmt-ip-address subnet}
no system settings mgmt {dhcp | ip address mgmt-ip-address }
Syntax Description ip address mgmt-ip-address Specifies the management IP address.
subnet Specifies the IP subnet for the management IP address.
Command Default By default, the management interface is assigned the static IP address 192.168.1.1.
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines You can configure DHCP either on the WAN interface or the management interface; you cannot configure
DHCP on both the interfaces simultaneously.
Before configuring the management interface with DHCP, delete the default gateway. After you configure
DHCP on the management interface, either reboot the system or enter the command hostaction
mgmt-dhcp-renew to renew the DHCP IP address.
Example
The following command sets the IP address and netmask for the management interface:
nfvis(config) system settings mgmt ip address 192.168.1.2 255.255.255.0
nfvis(config)commit
The following command configures DHCP on the management interface:
nfvis(config)# no system settings default-gw
nfvis(config)# system settings mgmt dhcp
nfvis(config)# commit
nfvis# hostaction mgmt-dhcp-renew
nfvis# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
18
System and IP Configuration Commands
system settings wan
system settings wan
To configure the WAN interface either with a static IP address or with DHCP, use the system settings wan
command in global configuration mode.
system settings wan { dhcp | ip address wan-ip-address netmask-address | vlan vlan-id}
no system settings wan { dhcp | ip address wan-ip-address netmask-address | vlan vlan-id}
Syntax Description ip-address wan-ip-address The WAN IP address.
netmask netmask-address The netmask for the WAN IP
address.
vlan vlan-id Specifies the VLAN tagging ID.
Valid range: 1-4094
If no VLAN is configured, the
default value is set to "untag".
Command Default By default, the WAN interface is configured with DHCP.
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines You can configure DHCP either on the WAN interface or the management interface; you cannot configure
DHCP on both the interfaces simultaneously.
Before configuring the WAN interface with DHCP, delete the default gateway. After you configure DHCP
on the WAN interface, either reboot the system or enter the command hostaction wan-dhcp-renew to renew
the DHCP IP address.
Example
The following command sets the IP address and netmask for the WAN interface:
nfvis(config)# system settings wan ip-address 172.19.162.209 255.255.255.0
nfvis(config)# commit
The following command configures DHCP on the WAN interface:
nfvis(config)# no system settings default-gw
nfvis(config)# system settings wan dhcp
nfvis(config)# commit
nfvis# hostaction wan-dhcp-renew
nfvis# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
19
System and IP Configuration Commands
system storage
system storage
To configure the system storage, use the system storage command in global configuration mode. Use the no
form of the command to delete the storage configuration.
system storage storage_name storagetype storagetype storage_space_total_gb storage_space_total_gb
server_ip server_ip server_path server_path
no system storage storage_name
Syntax Description storage_name Specifies the storage name.
storagetype storagetype Specifies the storage type. Valid values are internal, iscsi,
nfs, and not_enabled.
storage_space_total_gb Specifies the total storage space.
storage_space_total_gb
server_ip server_ip Specifies the IP address of the remote storage device server.
server_path server_path Specifies the remote server directory path.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis(config)# system storage nfs_storage
Value for 'storagetype' [internal,iscsi,nfs,not_enabled]: nfs
Value for 'storage_space_total_gb' (<decimal number>): 100
Value for 'server_ip' (<string, min: 1 chars, max: 80 chars>): 198.51.100.1
Value for 'server_path' (<string, min: 1 chars, max: 64 chars>): /export/vm/sample
nfvis(config-storage-nfs_storage)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
20
System and IP Configuration Commands
show system settings
show system settings
To display the system settings, use the show system settings command in privileged EXEC mode.
show system settings [brief]
Syntax Description brief Displays brief system settings.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 Brief parameter was added and
other parameters were removed.
3.5.1 This command was introduced.
Usage Guidelines None
Example
nfvis# show system settings
system settings brief lan-br
ipv4_address 192.0.2.1
ipv4_netmask 255.255.255.0
ipv4_dhcp disabled
global_ipv6_address ::
global_prefixlen 0
link_local_ipv6_address fe80::72db:98ff:fe07:1f35
link_local_prefixlen 64
ipv6_dhcp disabled
ipv6_slaac disabled
system settings brief wan-br
ipv4_address 198.51.100.1
ipv4_netmask 255.255.255.0
ipv4_dhcp disabled
global_ipv6_address ::
global_prefixlen 0
link_local_ipv6_address fe80::72db:98ff:fe70:2f6e
link_local_prefixlen 64
ipv6_dhcp enabled
ipv6_slaac disabled
ipv6_dhcp_state Stateful
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
21
System and IP Configuration Commands
show system settings-native
show system settings-native
To display all information related to management settings, use the show system settings-native command
in privileged EXEC mode.
show system settings-native [dns | domain | gateway | hostname | mgmt | wan vlan]
Syntax Description dns (Optional) DNS details.
domain (Optional) Domain name.
gateway (Optional) Default gateway details.
hostname (Optional) Hostname details.
mgmt (Optional) Management interface details.
wan (Optional) Wan interface details
vlan (Optional) Provides information about the VLAN tag.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Examples
The following is a sample output of the show system settings-native command without any keywords:
nfvis# show system settings-native
system settings-native mgmt ip-info interface lan-br
system settings-native mgmt ip-info ipv4_address 192.168.1.1
system settings-native mgmt ip-info netmask 255.255.255.0
system settings-native mgmt ip-info ipv6_address fe80::7aba:f9ff:feee:2f97
system settings-native mgmt ip-info prefixlen 64
system settings-native mgmt ip-info mac_address 80:e0:1d:37:93:47
system settings-native mgmt ip-info mtu 1500
system settings-native mgmt ip-info txqueuelen 0
system settings-native mgmt stats rx_packets 64157
system settings-native mgmt stats rx_bytes 8869998
system settings-native mgmt stats rx_errors 0
system settings-native mgmt stats rx_dropped 101
system settings-native mgmt stats rx_overruns 0
The following is a sample output of the show system settings-native command to verify the VLAN
configuration details. If no VLAN is configured, the default setting (untagged) is displayed as shown
below:
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
22
System and IP Configuration Commands
show system settings-native
nfvis# show system settings-native wan vlan tag
system settings-native wan vlan tag untagged
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
23
System and IP Configuration Commands
show system top
show system top
To display the top system processes, use the show system top command in privileged EXEC mode.
show system top
Syntax Description This command has no arguments or keywords.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system top
top - 14:35:44 up 12 min, 1 user, load average: 0.00, 0.11, 0.17
Tasks: 272 total, 1 running, 271 sleeping, 0 stopped, 0 zombie
%Cpu(s): 0.6 us, 0.2 sy, 0.0 ni, 99.2 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st
KiB Mem : 16158248 total, 14234804 free, 1435900 used, 487544 buff/cache
KiB Swap: 8388604 total, 8388604 free, 0 used. 14467448 avail Mem
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
1 root 20 0 44028 6628 3904 S 0.0 0.0 0:04.90 systemd
2 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kthreadd
3 root 20 0 0 0 0 S 0.0 0.0 0:00.02 ksoftirqd/0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
24
System and IP Configuration Commands
show system disk-space
show system disk-space
To display information about the system disk space, use the show system disk-space command in privileged
EXEC mode.
show system disk-space
Syntax Description This command has no arguments or keywords.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system disk-space
ASSOCIATED
PHYSICAL TOTAL SIZE SIZE USE
DISK NAME DISK SIZE USED AVAILABLE PERCENT
------------------------------------------------------------
lv_data sdf2 45G 321M 42G 1%
lv_var sdf2 2.0G 461M 1.4G 26%
lv_root sdf2 7.8G 1.7G 5.7G 23%
extdatastore1 sdd 917G 77M 871G 1%
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
25
System and IP Configuration Commands
show system file-handles
show system file-handles
To display information about the system file handles, use the show system file-handles command in privileged
EXEC mode.
show system file-handles
Syntax Description This command has no arguments or keywords.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system file-handles
2848 0 780124
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
26
System and IP Configuration Commands
show system processes
show system processes
To display information on the processes in the system, use the show system processes command in privileged
EXEC mode.
show system processes [process process-name]
Syntax Description process process-name (Optional) Name of the process.
Command Default Display information on all the processes in the system.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show system processes
PID CPU MEM VSZ RSS START TIME CMD
--------------------------------------------------
USER PID %CPU %MEM VSZ RSS TTY STAT
root 1 0.0 0.0 192156 7424 ? Ss
root 1 0.0 0.0 192156 7424 ? Ss
root 1 0.0 0.0 192156 7424 ? Ss
root 1 0.0 0.0 192156 7424 ? Ss
root 1 0.0 0.0 192156 7424 ? Ss
root 1 0.0 0.0 192156 7424 ? Ss
root 1 0.0 0.0 192156 7424 ? Ss
root 1 0.0 0.0 192156 7424 ? Ss
root 1 0.0 0.0 192156 7424 ? Ss
root 1 0.0 0.0 192156 7424 ? Ss
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
27
System and IP Configuration Commands
show system services
show system services
To display information on the services in the system, use the show system services command in privileged
EXEC mode.
show system services [service service-name]
Syntax Description service service-name (Optional) Name of the service.
Command Default Display information on all the services in the system.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show system services service auditd.service
UNIT LOAD ACTIVE SUB DESCRIPTION
------------------------------------------------------
auditd.service loaded active running Security
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
28
System and IP Configuration Commands
show system status
show system status
To display system defaults and services status, use the show system status command in privileged EXEC
mode.
show system status [diagnostics entity-name [status | type]]
Syntax Description entity-name (Optional) Name of the entity or service.
status (Optional) Display the entity or service status.
type (Optional) Display the type of the entity or service.
Command Default Show the status of all the entities in the system.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show system status diagnostics wan-br
NAME STATUS TYPE
--------------------------------
wan-br OK default-bridge
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
29
System and IP Configuration Commands
show platform-detail
show platform-detail
To display the hardware information, port details, switch details and software packages related to the platform,
use the show platform-detail command in privileged EXEC mode.
show platform-detail [hardware_info | port_detail | software_packages | switch_detail]
Syntax Description hardware_info The hardware information of the platform.
port_detail The details of the ports used by the platform.
software_packages The software packages installed on the platform.
switch_detail The details of the switch on the platform.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
30
System and IP Configuration Commands
show version
show version
To display the name, version number and build date of the NFVIS software that is currently running in the
system, use the show version command in privileged EXEC mode
show version [build-date | name | version]
Syntax Description build-date (Optional) The build date of the version.
name (Optional) The name of the version.
version (Optional) The version number of the version.
Command Default Displays the name, version number, and build date of Cisco Enterprise NFVIS.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following is the sample output from the show versioncommand:
nfvis# show version
version name "Enterprise NFV Infrastructure Software"
version version 3.5.1-FC4
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
31
System and IP Configuration Commands
show free-memory
show free-memory
To display information about free memory, use the show free-memory command in privileged EXEC mode.
show free-memory
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# show free-memory
total used free shared buff/cache available
Mem: 128660 2761 120879 15 5020 125222
Swap: 16383 0 16383
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
32
System and IP Configuration Commands
show certificate
show certificate
To show all certificates and related files in the system, use the show certificate command in privileged EXEC
mode.
show certificate
Syntax Description This command has no keywords or parameters.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# show certificates
File Name Type Last Modified Size
ca-bundle.legacy.crt ca-trust Wed Mar 15 12:08:40 2017 59653
ca-bundle.trust.crt ca-trust Fri Oct 6 10:39:53 2017 346654
email-ca-bundle.pem ca-trust Fri Oct 6 10:39:53 2017 208874
tls-ca-bundle.pem ca-trust Fri Oct 6 10:39:53 2017 262042
objsign-ca-bundle.pem ca-trust Fri Oct 6 10:39:53 2017 208976
server.key nginx Fri Oct 6 11:06:12 2017 1679
server.crt nginx Fri Oct 6 11:06:12 2017 964
server.key self-signed Fri Oct 6 11:06:12 2017 1679
server.csr self-signed Fri Oct 6 11:06:12 2017 887
server.crt self-signed Fri Oct 6 11:06:12 2017 964
ca-bundle.crt tls Fri Oct 6 10:39:53 2017 262042
ca-bundle.trust.crt tls Fri Oct 6 10:39:53 2017 346654
cert.pem tls Fri Oct 6 10:39:53 2017 262042
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
33
System and IP Configuration Commands
show file
show file
To show the contents of a file, use the show file command in privileged EXEC mode.
show file filepath_name
Syntax Description filepath_name Specifies the location and name of the file.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# show file /data/intdatastore/logs/2017-10/confd_devel.log-20171008
<DEBUG> 7-Oct-2017::19:30:08.444 nfvis confd[3626]: devel-cdb connect from python
<DEBUG> 7-Oct-2017::19:30:08.444 nfvis confd[3626]: devel-cdb client python has pid 3724/174
<DEBUG> 7-Oct-2017::19:30:08.444 nfvis confd[3626]: devel-cdb new session on operational
for python
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
34
System and IP Configuration Commands
show cores
show cores
To show crash core files, run the show cores command in privileged EXEC mode.
show cores
Syntax Description This command has no keywords or parameters.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was
introduced.
Usage Guidelines None
nfvis# show cores
Local storage:
File Name Last Modified Size
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
35
System and IP Configuration Commands
show nfv_mode
show nfv_mode
To show the NFV mode, use the show nfv_mode command in privileged EXEC mode.
show nfv_mode
Syntax Description This command has no keywords or parameters.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
nfvis# show nfv_mode
nfv_mode: vbranch_nfv
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
36
PnP Commands
• pnp action, on page 38
• pnp automatic, on page 39
• pnp static, on page 41
• show pnp, on page 42
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
37
PnP Commands
pnp action
pnp action
To start, stop, and restart a PnP action,use the pnp action command in global configuration mode.
pnp action command {start | stop | restart}
Syntax Description start Starts a PnP action.
stop Stops a PnP action.
restart Restarts a PnP action.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following example shows how to use the pnp action command:
nfvis(config)# pnp action command start
nfvis(config)# pnp action command stop
nfvis(config)# pnp action command restart
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
38
PnP Commands
pnp automatic
pnp automatic
To enable or disable automatic mode for PnP discovery process, use the pnp automatic command in global
configuration mode. Use the no form of this command to put the automatic PnP discovery method in default
mode (enabled) with a retry timeout of 60 seconds.
pnp automatic {cco | cco-ipv6 | dhcp | dhcp-ipv6 | dns-ipv6 | dns | timeout value} {enable |
disable}
no pnp automatic
Syntax Description cco Specifies the use of the Cisco Cloud Device Redirect tool available in the Cisco Software
Central for automatic PnP discovery.
cco-ipv6 Specifies the use of the Cisco Cloud Device Redirect tool available in the Cisco Software
Central for automatic PnP discovery for IPv6.
dhcp Specifies the use of a IPv4 DHCP server for automatic PnP discovery.
dhcp-ipv6 Specifies the use of a IPv6 DHCP server for automatic PnP discovery.
dns Specifies the use of a IPv4 DNS server for automatic PnP discovery.
dns-ipv6 Specifies the use of a IPv6 DNS server for automatic PnP discovery.
timeout value Specifies the timeout value in seconds. The default value is 60.
enable Enables the PnP discovery method.
disable Disables the PnP discovery method.
Command Default The automatic discovery mode for DHCP, DNS, and CCO is enabled.
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines You can enable or disable the options as required. For example, you can enable all options or keep one enabled,
and the rest disabled. You cannot disable both static and automatic PnP discovery modes at the same time.
You must restart PnP action every time you make changes to the PnP discovery configuration. You can do
this using the pnp action command restart command.
Example
The following example shows how to enable automatic mode for PnP discovery process:
nfvis(config)# pnp automatic dhcp enable
nfvis(config)# pnp automatic dns enable
nfvis(config)# pnp automatic cco enable
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
39
PnP Commands
pnp automatic
nfvis(config)# pnp automatic timeout 100
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
40
PnP Commands
pnp static
pnp static
To specify a static IP address for the Cisco Network PnP server, use the pnp static command in global
configuration mode. To remove the PnP static IP address configuration , use the no form of the command
with the static keyword. To clear any PnP static and automatic configurations, and put all the automatic
configurations in default mode, which is enabled, with a retry timeout of 60 seconds, use the no pnp command.
pnp static {ip-address ipv4-address | ipv6-address ipv6-address} [{port number}]
no pnp static
Syntax Description ip-address ipv4-address Specifies the IPv4 address.
ipv6-address ipv6-address Specifies the IPv6 address.
port number (Optional) Specifies the port number. Valid range is from 0 to 65535.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 The ipv6-address parameter was
added.
3.5.1 This command was introduced.
Usage Guidelines You cannot disable both static and automatic PnP discovery modes at the same time. You must restart PnP
action every time you make changes to the PnP discovery configuration. You can do this using the pnp action
command restart.
Example
The following example shows how to configure a static IP address for the Cisco Network PnP server:
nfvis(config)# pnp automatic dhcp disable
nfvis(config)# pnp automatic dns disable
nfvis(config)# pnp automatic cco disable
nfvis(config)# pnp static ip-address 192.0.2.0 port 80
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
41
PnP Commands
show pnp
show pnp
To verify the configuration of PnP discovery methods, use the show pnp command in privileged EXEC mode.
show pnp
Syntax Description This command has no arguments or keywords.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following sample output of the show pnp command shows that the static discovery mode is
enabled, and the automatic discovery mode is disabled.
nfvis# show pnp
pnp status response "PnP Agent is running\n"
pnp status ip-address 192.0.2.0
pnp status port 80
pnp status transport ""
pnp status created_by user
pnp status dhcp_opt43 0
pnp status dns_discovery 0
pnp status cco_discovery 0
pnp status timeout 100
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
42
Resource Commands
• show resources cpu-info allocation, on page 44
• show resources cpu-info cpus, on page 45
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
43
Resource Commands
show resources cpu-info allocation
show resources cpu-info allocation
To get information on the number of CPUs allocated to VMs and the CPUs that are already used by the VMs,
use the show resources cpu-info allocation command in privileged EXEC mode.
show resources cpu-info allocation [total-sockets | cores-per-socket | logical-cpus-used-by-system
| logical-cpus-used-by-vnfs | logical-cpus-used-dedicated | logical-cpus-used-sharable |
total-logical-cpus]
Syntax Description total-sockets (Optional) Total sockets allocated.
cores-per-socket (Optional) Number of cores per socket.
logical-cpus-used-by-system (Optional) Number of CPUs used by the system.
logical-cpus-used-dedicated (Optional) Number of dedicated CPUs.
total-logical-cpus (Optional) Total number of CPUs.
logical-cpus-used-by-vnfs (Optional) Number of CPUs used by VNFs.
Command Default Complete information about CPU allocation to VMs.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following is the sample output from the show resources cpu-info allocation command:
nfvis# show resources cpu-info allocation
resources cpu-info allocation total-sockets 1
resources cpu-info allocation cores-per-socket 8
resources cpu-info allocation total-logical-cpus 16
resources cpu-info allocation logical-cpus-used-by-system 2
resources cpu-info allocation logical-cpus-used-by-vnfs 14
resources cpu-info allocation logical-cpus-used-dedicated 12
resources cpu-info allocation logical-cpus-used-sharable 2
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
44
Resource Commands
show resources cpu-info cpus
show resources cpu-info cpus
To display information on the VMs running in all the physical CPUs or a specific physical CPU in the system,
use the show resources cpu-info cpus command in privileged EXEC mode.
show resources cpu-info cpus [cpu cpu-id]
Syntax Description cpu cpu-id (Optional) The ID of the physical CPU.
Command Default Display information on the VMs running in all the physical CPUs.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following is a sample output from the show resources cpu-info cpus cpu 7 command:
nfvis# show resources cpu-info cpus cpu 7
CPU SOCKET CORE SYSTEM LOW VCPU
ID ID ID USE NAME VCPUS LATENCY ID
-----------------------------------------------------------------------
7 0 7 false 1471588629.ROUTER3 4 true 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
45
Resource Commands
show resources cpu-info cpus
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
46
Networks and Bridges Commands
• networks network, on page 48
• bridge, on page 51
• bridges bridge, on page 52
• show running-config bridges, on page 53
• show system networks, on page 54
• show system packages, on page 55
• ping, on page 56
• ping-ipv6, on page 57
• traceroute, on page 58
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
47
Networks and Bridges Commands
networks network
networks network
To add a bridge to a network, use the networks network command, in global configuration mode. To remove
the bridge from a network, use the no form of the command.
networks network networkname { bridge bridgename | sriov true | trunk true | trunk false |
vlan vlannumber | vlan-range range }
no networks network networkname
Syntax Description network networkname Specifies the name of the network.
bridge bridgename Specifies the name of the bridge.
sriov true Specifies the SRIOV network.
trunk true Adds the network to trunk mode.
Note The trunk mode is applicable only to the interfaces attached to a
network, for example, a VNF or anvNIC. The trunk mode is not
applicable for Physical NICs (pNICs).
trunk false Removes the network from trunk mode and puts it in access mode.
vlan vlannumber Specifies the VLAN number to be associated with the network.
vlan-range range Specifies the VLAN range.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
4.8.1 The vlan-range keyword was added.
Example
The following example shows how to add a bridge to a network:
nfvis(config)# bridges bridge eth2-1-br
nfvis(config-bridge-eth2-1-br)# port eth2-1
nfvis(config-port-eth2-1)# commit
nfvis(config)# networks network eth2-1-net bridge eth2-1-br
nfvis (config-network-eth2-1-net)# commit
The following example shows how to create a SRIOV network:
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
48
Networks and Bridges Commands
networks network
nfvis(config)# networks network eth2-1-SRIOV-1 sriov true
nfvis(config-network-eth2-1-SRIOV-1)# commit
The following example shows how to add a network into trunk mode:
nfvis(config)# networks network eth2-1-net trunk true
nfvis(config-network-eth2-1-net)# commit
The following example shows how to remove a network from trunk mode:
nfvis(config)# networks network eth2-1-net trunk false
nfvis(config-network-eth2-1-net)# commit
The following example shows how to associate a VLAN with a network:
nfvis(config)# networks network eth2-1-net vlan 100 trunk true
nfvis(config-network-eth2-1-net)# commit
nfvis# show running-config networks network eth2-1-net
networks network eth2-1-net
vlan [ 100 ]
trunk true
bridge eth2-1-br
The following example shows how to configure a VLAN range:
nfvis(config)# networks network eth2-1-net bridge eth2-1-br vlan-range [ 100-103 200 205-207
]
nfvis(config-network-eth2-1-net)# commit
nfvis# show running-config networks network eth2-1-net
networks network eth2-1-net
vlan-range [ 100-103 200 205-207 ]
bridge eth2-1-br
nfvis# show system networks network eth2-1-net
system networks network eth2-1-net
bridge eth2-1-br
ports eth2-1
type openvswitch
vlan 100,101,102,103,200,205,206,207,1
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
49
Networks and Bridges Commands
networks network
Note • A SRIOV network in trunk mode does not support VLAN tagging.
nfvis(config)# networks network eth2-1-net sriov true
nfvis(config-network-eth2-1-net)# trunk true
nfvis(config-network-eth2-1-net)# vlan 100
nfvis(config-network-eth2-1-net)# commit
Aborted: SRIOV network in trunk mode does not support vlan tagging
• In access mode, only one VLAN tag is supported.
nfvis(config)# networks network eth2-1-net
nfvis(config-network-eth2-1-net)# vlan [ 100 200 300 ]
nfvis(config-network-eth2-1-net)# trunk false
nfvis(config-network-eth2-1-net)# commit
Aborted: Network eth2-1-net: Access mode supports 1 vlan tag only
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
50
Networks and Bridges Commands
bridge
bridge
To attach a SPAN session to a bridge, use the bridge command in session configuration mode. To remove
the SPAN session association, use the no form of the command.
bridge {lan-br | wan-br}
no bridge {lan-br | wan-br}
Syntax Description lan-br Specifies the LAN bridge.
wan-br Specifies the WAN bridge.
Command Default None
Command Modes Session configuration (config-session-2)#
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines For VLAN mirroring, the bridge must be configured. Configuration is rejected if a SPAN session is not applied
to a bridge. The bridge configuration is optional if the source or destination interface is configured for the
SPAN session.
Example
The following example shows how to attach a SPAN session to a bridge:
nfvis(config)# monitor session 2
nfvis(config-session-2)# bridge lan-br
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
51
Networks and Bridges Commands
bridges bridge
bridges bridge
To add a port or port channel to a bridge, use the bridges bridge command. To remove a port or port channel
from a bridge, use the no form of the command.
bridges bridge bridgename port portname
no bridges bridge bridgename port portname
Syntax Description bridgename Specifies the name of the bridge.
portname Specifies the name of the port or port channel.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# config
nfvis(config)# bridges bridge test-br port pc
nfvis(config-bridge-test-br)# commit
nfvis(config-bridge-test-br) # end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
52
Networks and Bridges Commands
show running-config bridges
show running-config bridges
To display the currently running bridge configuration, use the show running-config bridges command in
privileged EXEC mode.
show running-config bridges
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show running-config bridges
bridges bridge wan-br
port GE0-0
!
!
bridges bridge lan-br
port int-LAN
!
!
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
53
Networks and Bridges Commands
show system networks
show system networks
To display the information of the networks in the system, use the show system networks command in
privileged EXEC mode.
show system networks [network network-name [bridge | ports | type]]
Syntax Description network network-name (Optional) Name of the network.
bridge (Optional) The bridge for the network.
port (Optional) The port for the network.
type (Optional) The type of network.
Command Default All the networks in the system are displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show system networks
NETWORK BRIDGE PORTS TYPE
------------------------------------------------------
default virbr0 N/A
lan-net lan-br eth1,vnet4 openvswitch
service-net service-net-br N/A openvswitch
wan-net wan-br eth0 openvswitch
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
54
Networks and Bridges Commands
show system packages
show system packages
To display information on the packages in the system, use the show system packages command in privileged
EXEC mode.
show system packages [package package-name [owner | version]]
Syntax Description package package-name (Optional) Name of the package.
owner (Optional) Owner of the package.
version (Optional) Version of the package.
Command Default Display information on all the packages in the system.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show system packages
NAME VERSION OWNER
--------------------------------------------------------------------
GeoIP.x86_64 1.5.0-9.el7 @anaconda
NetworkManager.x86_64 1:1.0.6-27.el7 @anaconda
NetworkManager-libnm.x86_64 1:1.0.6-27.el7 @anaconda
NetworkManager-team.x86_64 1:1.0.6-27.el7 @anaconda
NetworkManager-tui.x86_64 1:1.0.6-27.el7 @anaconda
Twisted.x86_64 13.1.0-1 @esc-lite
abrt.x86_64 2.1.11-36.el7.centos @anaconda
abrt-addon-ccpp.x86_64 2.1.11-36.el7.centos @anaconda
abrt-addon-kerneloops.x86_64 2.1.11-36.el7.centos @anaconda
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
55
Networks and Bridges Commands
ping
ping
To diagnose basic network connectivity to an IPv4 host, use the ping command in privileged EXEC mode.
ping {host-ip-address host-name} [count count] [pktsize pktsize] [interval interval] [ttl ttl]
Syntax Description host-ip-address Specifies the address of the IPv4 host.
host-name Specifies the name of the IPv4 host.
count count Specifies the number of ping packets to be sent.
pktsize pktsize Specifies the packet size. The default is 64 bytes.
interval interval Specifies the number of seconds to wait between
requests.
ttl ttl Specifies the hop limit.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis(config)# ping count 5 interval 2 pktsize 64 ttl 64 192.0.2.252
PING 192.0.2.252 (192.0.2.252) 64(92) bytes of data.
72 bytes from 192.0.2.252: icmp_seq=1 ttl=64 time=0.050 ms
72 bytes from 192.0.2.252: icmp_seq=2 ttl=64 time=0.041 ms
72 bytes from 192.0.2.252: icmp_seq=3 ttl=64 time=0.042 ms
72 bytes from 192.0.2.252: icmp_seq=4 ttl=64 time=0.033 ms
72 bytes from 192.0.2.252: icmp_seq=5 ttl=64 time=0.033 ms
--- 192.0.2.252 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 8000ms
rtt min/avg/max/mdev = 0.033/0.039/0.050/0.010 ms
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
56
Networks and Bridges Commands
ping-ipv6
ping-ipv6
To diagnose basic network connectivity to an IPv6 host, use the ping-ipv6 command in privileged EXEC
mode.
ping-ipv6 {host-ip-address host-name} [count count] [pktsize pktsize] [interval interval] [ttl
ttl]
Syntax Description host-ip-address Specifies the address of the IPv6 host.
host-name Specifies the name of the IPv6 host.
count count Specifies the number of ping packets to be sent.
pktsize pktsize Specifies the packet size. The default is 64 bytes.
interval interval Specifies the number of seconds to wait between
requests.
ttl ttl Specifies the hop limit.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis(config)# ping-ipv6 count 6 interval 2 pktsize 64 ttl 64 fe80::9c76:87ff:feba:5d40
PING fe80::9c76:87ff:feba:5d40(fe80::9c76:87ff:feba:5d40) 64 data bytes
72 bytes from fe80::9c76:87ff:feba:5d40%lan-br: icmp_seq=1 ttl=64 time=0.060 ms
72 bytes from fe80::9c76:87ff:feba:5d40%lan-br: icmp_seq=2 ttl=64 time=0.045 ms
72 bytes from fe80::9c76:87ff:feba:5d40%lan-br: icmp_seq=3 ttl=64 time=0.045 ms
72 bytes from fe80::9c76:87ff:feba:5d40%lan-br: icmp_seq=4 ttl=64 time=0.069 ms
72 bytes from fe80::9c76:87ff:feba:5d40%lan-br: icmp_seq=5 ttl=64 time=0.051 ms
72 bytes from fe80::9c76:87ff:feba:5d40%lan-br: icmp_seq=6 ttl=64 time=0.039 ms
--- fe80::9c76:87ff:feba:5d40 ping statistics ---
6 packets transmitted, 6 received, 0% packet loss, time 10000ms
rtt min/avg/max/mdev = 0.039/0.051/0.069/0.012 ms
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
57
Networks and Bridges Commands
traceroute
traceroute
To discover the routes that packets take when traveling to a destination, use the traceroute command in
privileged EXEC mode.
traceroute {ip-address host-name} interface interface-name [source source-ip-address] [max
max] [min min] [probes probes] [waittime waittime]
Syntax Description ip-address Specifies the destination IP address.
host-name Specifies the destination host name.
interface interface-name Specifies a source network interface.
source source-ip-address (Optional) Specifies a source IP address.
max max (Optional) Specifies the maximum time-to-live
(TTL) used in the outgoing probe packets. The
default value is 30.
min min (Optional) Specifies the minimum TTL used in
the first outgoing probe packet. The default value
is 1.
probes probes (Optional) Specifies the number of probes to be
sent at each TTL level. The default value is 3.
waittime waittime (Optional) Specifies the probe timeout in
seconds. The default value is 1.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# traceroute min 5 198.51.100.1
traceroute to 198.51.100.1 (198.51.100.1), 30 hops max, 60 byte packets
5 198.51.100.1 (198.51.100.1) 1.263 ms !X 1.157 ms !X 0.929 ms !X
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
58
VM Lifecycle Management Commands
• vm_lifecycle flavors, on page 60
• vm_lifecycle images, on page 61
• vm_lifecycle tenants tenant admin deployments, on page 65
• vmAction, on page 69
• vmBackupAction, on page 70
• vmConsole, on page 71
• vncconsole start, on page 72
• show vm_lifecycle opdata, on page 73
• show running-config vm_lifecycle, on page 76
• show running-config vm_packages, on page 77
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
59
VM Lifecycle Management Commands
vm_lifecycle flavors
vm_lifecycle flavors
To create a flavor, use the vm_lifecycle flavors command in global configuration mode. To remove a flavor,
use the no form of the command.
vm_lifecycle flavors flavor flavor-name vcpus vcpus memory_mb memory_mb root_disk_mb
root_disk_mb ephemeral_disk_mb ephemeral_disk_mb [swap_disk_mb swap_disk_mb]
no vm_lifecycle flavors flavor
Syntax Description flavor flavor-name Specifies the flavor name.
vcpus vcpus Specifies the number of vCPUs.
memory_mb memory_mb Specifies the memory size in megabytes.
root_disk_mb root_disk_mb Specifies the virtual root disk size in megabytes.
ephemeral_disk_mb ephemeral_disk_mb Specifies the size of a secondary ephemeral data disk.
swap_disk_mb swap_disk_mb (Optional) Specifies the size of swap space allocation.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines When deploying or modifying a VM, you can specify a flavor in active state.
To verify that the VM flavor is created, use the following commands in privileged EXEC mode:
show running-config vm_lifecycle flavors [flavor flavor-name]
show vm_lifecycle opdata flavors [flavor flavor-name]
Example
nfvis(config)# vm_lifecycle flavors flavor my_small vcpus 2 memory_mb 4096 root_disk_mb
8192 ephemeral_disk_mb 0
swap_disk_mb 0
nfvis(config-flavor-my_small)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
60
VM Lifecycle Management Commands
vm_lifecycle images
vm_lifecycle images
To register a VM image, use the vm_lifecycle images command in global configuration mode. To remove
the VM registration, use the no form of the command.
vm_lifecycle images image image-name src file-path [properties property property-name value
value]
no vm_lifecycle images image image-name
Syntax Description image image-name Specifies the image name.
src file-path Specifies the location of the image.
property property-name Specifies the name of the property to replace the corresponding
value inside the tar.gz while registering the image. For detailed
information about all supported properties, see the Usage
Guidelines section.
value value Specifies the property value to be replaced inside the tar.gz.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines A VM image registration is done only once per VM image. You can perform multiple VM deployments using
the registered VM image.
The following table provides information about the resources supported or required for the VM operation.
Table 1: VM Image Properties
Property Description
vnf_type Specifies the VM functionality.
Possible values are router, firewall, Windows, Linux,
and custom_type. Router and firewall are predefined
types.
name Specifies the name associated with the VM packaging.
This name is referenced for VM deployment.
version Specifies the version of the package.
bootup_time Specifies the bootup time of the VNF before it can be
reachable through ping. You can specify any value
in seconds. Specify value of -1 to not monitor the VM.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
61
VM Lifecycle Management Commands
vm_lifecycle images
Property Description
root_file_disk_bus Specifies the root image disk bus. Valid values are
virtio, scsi, and ide.
disk_x_file_disk_bus Specifies the disk bus for additional disk image. The
VM package supports up to 10 disks to be bundled
into the package such as disk_1_file_disk_bus,
disk_2_file_disk_bus, and disk_10_file_disk_bus.
Valid values are virtio, scsi, and ide.
root_image_disk_format Specifies the root image disk format. Valid values are
qcow2 and raw.
disk_x_image_format Specifies the image format for additional disk image.
The VM package supports up to 10 disks to be
bundled into the package such as
disk_1_image_format, disk_2_image_format, and
disk_10_image_format. Valid values are qcow2 and
raw.
console_type_serial Enables the serial console. Valid values are true and
false.
vcpu_min Specifies the minimum vCPUs required for a VM
operation.
vcpu_max Specifies the maximum vCPUs supported by a VM.
memory_mb_min Specifies the minimum memory in MB required for
VM operation.
memory_mb_max Specifies the maximum memory in MB supported by
a VM.
root_disk_gb_min Specifies the minimum disk size in GB required for
VM operation.
root_disk_gb_max Specifies the maximum disk size in GB supported by
a VM.
vnic_max Specifies the maximum number of vNICs supported
by a VM.
sriov_supported Enables SRIOV support by VM interfaces. Valid
values are true and false.
sriov_driver_list Specifies the list of drivers to enable the SRIOV
support.
pcie_supported Enables the PCI passthrough support by VM
interfaces. Valid values are true and false.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
62
VM Lifecycle Management Commands
vm_lifecycle images
Property Description
pcie_driver_list Specifies the list of vNICS to enable the PCI
passthrough support.
bootstrap_cloud_init_drive_type Mounts the day0 configuration file as disk. Default
is CD-ROM.
bootstrap_cloud_init_bus_type Default is IDE.
bootstrap_file Specifies the bootstrap file.
custom_property Specifies the custom properties that can be defined
within the custom_property tree. For example, for
ISRv, the technology packages are listed in this block.
If the Cisco Enterprise NFV portal is used to deploy
the VM, the portal prompts you for inputs for custom
properties fields, and can pass the values to the
bootstrap configuration.
profiles Specifies the list of VM deployment profiles.
Minimum one profile is required.
default_profile Specifies the default profile that is used when no
profile is specified during deployment.
monitoring_supported Specifies that the VM supports monitoring to detect
failures. Valid values are true and false.
monitoring_methods Specifies the method to monitor a VM. Currently,
only ICMP ping is supported. This parameter is
required if the monitoring_supported parameter is
set to true.
low_latency Specifies if a VM's low latency (for example, router
and firewall) gets dedicated resource (CPU) allocation.
Otherwise, shared resources are used. Valid values
are true and false.
privileged_vm Allows special features like promiscuous mode and
snooping. Valid values are true and false. The default
value is false.
virtual_interface_model Specifies the virtual interface model.
thick_disk_provisioning Configures thick disk provisioning. Valid values are
true and false. The default value is false.
placement Specifies placement datastore. For NFS, valid value
is nfs-storage.
For Cisco ENCS external datastore, allowed values
are datastore2, datastore3. The default value is
datastore1.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
63
VM Lifecycle Management Commands
vm_lifecycle images
Property Description
profile Specifies the profile for defining the resources
required for VM deployment. This profile is
referenced during VM deployment.
name Specifies the profile name.
description Specifies the description of the profile.
vcpus Specifies the vCPU number in a profile.
memory_mb Specifies the memory in MB in a profile.
root_disk_mb Specifies the disk size in MB in a profile.
To verify that the VM image is registered, use the following commands in privileged EXEC mode:
show running-config vm_lifecycle images [image image-name]
show vm_lifecycle opdata images [image image-name]
Example
The following example shows how to register a VM image:
nfvis(config)# vm_lifecycle images image isrv src
file://data/intdatastore/uploads/isrv-universalk9.16.03.01.tar.gz
nfvis(config-image-isrv)# properties property vnf_type value router
nfvis(config-property-vnf_type)# exit
nfvis(config-image-isrv)# properties property console_type_serial value true
nfvis(config-image-isrv)# properties property bootup_time value -1
nfvis(config-property-bootup_time)# exit
nfvis(config-image-isrv)# commit
nfvis(config-image-isrv)# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
64
VM Lifecycle Management Commands
vm_lifecycle tenants tenant admin deployments
vm_lifecycle tenants tenant admin deployments
To deploy a VM with its attributes, use the vm_lifecycle tenants tenant admin deployments command in
global configuration mode along with the other commands given in the Usage Guidelines section. To undeploy
a VM, use the no form of the command.
vm_lifecycle tenants tenant admin deployments deployment deployment-name vm_group
vm-group-name bootup_time valueimage image-name flavor flavor-name
no vm_lifecycle tenants tenant admin deployments deployment deployment-name
Usage Guidelines 1. Create a deployment and a vm_group.
vm_lifecycle tenants tenant admin deployments deployment deployment-name vm_group
vm-group-name bootup_time value image image-name flavor flavor-name
2. In the vm_group configuration mode, configure VM interfaces and optional model name, IP address, and
port forwarding.
interfaces interface nicid network network-name [model model-name] [ip_address ip-address]
[port_forwarding port port-type protocol protocol-name vnf_port port-num external_port_range
port-num-start port-num-end]
exit
3. In vm_group configuration mode, configure scaling rule.
scaling min_active min_active max_active max_active
4. (Optional) In vm_group configuration mode, configure placement.
placement type zone_host host placement-host-name
5. In vm_group configuration mode, configure monitoring policy rule for a monitored VM for which the
bootup_time is specified.
rules admin_rules rule rule-name action actions
exit
kpi_data kpi rule-name metric_value value metric_cond value metric_type metric_type metric_collector
type type nicid vnic-id poll_frequency value polling_unit unit continuous_alarm continuous_alarm_value
6. Commit the configuration.
commit
To verify, use following two commands in privileged EXEC mode
show running-config vm_lifecycle tenants tenant admin deployments [deployment-name]
show vm_lifecycle opdata tenants tenant admin deployments [deployment-name]
Syntax Description deployment deployment-name Specifies the VM deployment name.
vm_group vm-group-name Specifies the VM group name.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
65
VM Lifecycle Management Commands
vm_lifecycle tenants tenant admin deployments
bootup_time value Specifies the VM bootup time. Bootup time can vary depending on the
VM image that you have selected. For example, bootup time is 600 seconds
for a Cisco ISRv image. If no monitoring is required for the VM, set the
bootup time as -1.
Note A monitored VM must have a valid bootup time. The
corresponding KPI fields are mandatory for the monitored
VM. For an unmonitored VM, the KPI fields are optional.
image image-name Specifies the image name that was used for registering. The image must
be in ACTIVE state.
flavor flavor-name Specifies the flavor name. The flavor must be in ACTIVE state.
interfaces interface nicid Specifies the virtual interface ID.
Note At least one NIC ID is required for monitored VMs. For
unmonitored VMs, NIC ID is optional.
network network-name Specifies the name of the network attached to the NIC ID. All networks
(such as LAN and WAN), except the internal management network, require
an IP address.
The vNIC attachment to the internal management network is required only
for VMs that require monitoring. If this interface is used for monitoring,
network must be set to int-mgmt-net.
model model-name Specifies the model name. Possible values are: e1000, i82551, i82557b,
i82559er, ne2k_pci, pcnet, rtl8139, and virtio.
The default value is virtio. This is an optional parameter.
ip_address ip_address Specifies the IPv4 address. This is an optional parameter.
port_forwarding Configures port forwarding.
When port forwarding is enabled, you must specify the values in the
following fields: port, protocol, vnf_port, and external_port_range.
port port-type Specifies the port type. Possible values are SSH, HTTPS, TCP, and Telnet.
protocol protocol-name Specifies the protocol. Valid value is TCP.
vnf_port port-num Specifies the port number corresponding to the specified protocol.
external_port_range Specifies the unique port number to specify the start and end range for
port-num-start port-num-end ports.
scaling Specifies how many instances of a particular type of VM need to be
instantiated, and whether elastic scale-in and scale-out are required.
min_active min_active Defines the minimum number of VMs to be activated.
max_active max_active Defines the maximum number of VMs to be activated.
placement Configures placement datastore. This is an optional parameter.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
66
VM Lifecycle Management Commands
vm_lifecycle tenants tenant admin deployments
type zone_host Specifies the placement type. Value must be zone_host.
host placement-host-name Specifies the name of the placement datastore. For NFS, valid value is
nfs-storage. For Cisco ENCS external datastore, allowed values are
datastore2, datastore3. The default value is datastore1.
rules admin_rules Configures monitoring policy rule. These are the rules that an administrator
specifies when the service is registered.
This parameter is mandatory if the VM is a monitored VM, that is, its
bootup time is non-zero.
rule rule-name Specifies the name of the monitoring event rule.
action actions Specifies the list of actions which this policy triggers.
• ALWAYS log—Whether the event is pingable or not, the details are
always logged.
• FALSE recover autohealing—The action identified by this keyword
is triggered, and the VM is recovered without the administrator's
intervention.
• TRUE servicebooted.sh—The action identified by this keyword in
the dynamic mapping file is triggered when the VM moves from a
non-pingable to a pingable state.
You can specify actions in the following format: action [ "ALWAYS log"
"FALSE recover autohealing" "TRUE servicebooted.sh" ].
kpi_data Specifies the Key Performance Indicators (KPI) data.
kpi rule-name Specifies the KPI rule name.
metric_value value Specifies the metric threshold value of the KPI.
metric_cond value Specifies the direction of the metric value change for the KPI. Valid values
are the following:
• GE and GT: An alarm is sent when the metric value increases from
a lower position to equal or exceed the specified value.
• LE and LT: An alarm is sent when the metric value decreases from
a higher position to equal or go down the specified value.
metric_type type Specifies the metric type. Valid metric types are INT8, UINT8, INT16,
UINT16, INT32, UINT32, FLOAT, DOUBLE, and STRING.
metric_collector Configures the metrics that needs to be monitored and at what frequency
should the monitoring happen.
type type Specifies the type to be monitored; for example, ICMPPing. If the image
boot-up time is provided, monitoring must be set to ICMPPing.
nicid vnic-id Specifies the card ID of the interface through which this VM is monitored.
It should be the ID specified for one of interfaces in the payload.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
67
VM Lifecycle Management Commands
vm_lifecycle tenants tenant admin deployments
poll_frequency value Specifies the ICMP ping frequency value.
polling_unit unit Specifies the ICMP ping frequency unit. Possible values are minutes and
seconds.
continuous_alarm value Specifies that the continuous events need to be generated. Valid values are
true and false.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following example shows how to deploy a VM:
nfvis(config)# vm_lifecycle tenants tenant admin deployments deployment dep1 vm_group router1
bootup_time 600 image
isrv flavor ISRv-small
nfvis(config-vm_group-router1)# interfaces interface 0 network int-mgmt-net port_forwarding
port ssh protocol tcp
vnf_port 22 external_port_range 20024 20024
nfvis(config-port-ssh)# exit
nfvis(config-interface-0)# exit
nfvis(config-vm_group-router1)# interfaces interface 1 model virtio network lan-net
nfvis(config-interface-1)# exit
nfvis(config-vm_group-router1)# rules admin_rules rule VM_ALIVE action [ "ALWAYS log" "FALSE
recover autohealing"
"TRUE servicebooted.sh" ]
nfvis(config-rule-VM_ALIVE)# exit
nfvis(config-vm_group-router1)# kpi_data kpi VM_ALIVE metric_value 1 metric_cond GT
metric_type UINT32 metric_collector
type ICMPPing nicid 0 poll_frequency 3 polling_unit seconds continuous_alarm false
nfvis(config-kpi-VM_ALIVE)# exit
nfvis(config-vm_group-router1)# scaling min_active 1 max_active 1
nfvis(config-vm_group-router1)# placement zone_host host datastore1
nfvis(config-placement-zone_host)# exit
nfvis(config-vm_group-router1)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
68
VM Lifecycle Management Commands
vmAction
vmAction
To specify a VM action, use the vmAction command in privileged EXEC mode.
vmAction action vmName name
Syntax Description action Specify the action. Valid values are DISABLE_MONITOR, ENABLE_MONITOR, REBOOT,
RECOVER, START, and STOP.
name Specify the VM name. This VM name is the internally-generated name. Use the show vm_lifecycle
opdata tenants tenant admin deployments command to get the VM NAME per deployment.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# vmAction actionType STOP vmName
1513193832_ROUTER_0_15c32f49-0d95-4b7a-8a84-ba7de3c1d6f9
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
69
VM Lifecycle Management Commands
vmBackupAction
vmBackupAction
To back up a VM, use the vmBackupAction command in privileged EXEC mode.
vmBackupAction vmName name actionType action [backupName backupname]
Syntax Description vmName name Specifies the VM name.
actionType action Specifies the action type. Valid value is EXPORT.
backupName Specifies the backup name for the VM.
backupname
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# vmBackupAction vmName isrvtest1 actionType EXPORT
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
70
VM Lifecycle Management Commands
vmConsole
vmConsole
To enable VM serieal console, use the vmConsole command in privileged EXEC mode.
vmConsole vm-domain-name
Syntax Description vm-domain-name Specifies the VM domain name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Usage Guidelines If the VM does not support a serial console, the vmConsole command returns this message, "Serial console
not available".
To exit the VM console you must enter ctrl+] and then enter send escape.
Example
The following example shows how a VM is connected to its domain using the serial console:
nfvis# vmConsole fortinet.fortinet
Connected to domain fortinet.fortinet
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
71
VM Lifecycle Management Commands
vncconsole start
vncconsole start
To get information about the VNC console, use the vncconsole start command in privileged EXEC mode.
vncconsole start deployment-name name vm-name name
Syntax Description deployment-name name Specifies the deployment name.
vm-name name Specifies the VM name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# vncconsole start deployment-name 1461784490 vm-name isrvtest1
vncconsole-url :6001/vnc_auto.html
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
72
VM Lifecycle Management Commands
show vm_lifecycle opdata
show vm_lifecycle opdata
To display the overall operational status of VM life cycle, use the show vm_lifecycle opdata command in
privileged EXEC mode.
show vm_lifecycle opdata [{flavors flavor flavor-name | images image image-name | networks
network network-name | stats | status | system-config | tenants tenant tenant-name
[deployments [vm_group vm-group-name]]}]
Syntax Description flavors flavor flavor-name Specifies the flavor name.
images image image-name Specifies the image name.
networks network network-name Specifies the network name.
stats Displays the VM life cycle statistics.
status Displays the VM life cycle status.
system-config Displays the VM life cycle configuration.
tenants tenant tenant-name Specifies the tenant name.
deployments Displays the deployment status.
vm_group vm-group-name Displays the deployment status for the specified VM group.
Command Default Displays the overall operational status of the VM life cycle.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
nfvis# show vm_lifecycle opdata
vm_lifecycle opdata status OPER_UP
vm_lifecycle opdata stats hostname nfvis
vm_lifecycle opdata stats os_name Linux
vm_lifecycle opdata stats os_release 3.10.0-327.36.3.el7.x86_64
vm_lifecycle opdata stats arch amd64
vm_lifecycle opdata stats uptime 1395859
vm_lifecycle opdata stats cpu cpu_num 16
vm_lifecycle opdata networks network int-mgmt-net
netid a5bc70f6-5841-4af5-bcec-6710d28e7f55
shared true
admin_state true
provider_network_type local
status active
NO
NAME SUBNETID CIDR GATEWAY GATEWAY
DHCP IPVERSION
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
73
VM Lifecycle Management Commands
show vm_lifecycle opdata
---------------------------------------------------------------------------------------------------------------
int-mgmt-net-subnet 004db62f-ae89-43f7-bc24-dfa2d9caa3eb 192.0.2.0/24 192.0.2.1 false
false 4
vm_lifecycle opdata tenants tenant admin
tenant_id AdminTenantId
networks network int-mgmt-net
netid a5bc70f6-5841-4af5-bcec-6710d28e7f55
shared true
admin_state true
provider_network_type local
status active
NO
NAME SUBNETID CIDR GATEWAY GATEWAY
DHCP IPVERSION
---------------------------------------------------------------------------------------------------------------
int-mgmt-net-subnet 004db62f-ae89-43f7-bc24-dfa2d9caa3eb 192.0.2.0/24 192.0.2.1 false
false 4
nfvis# show vm_lifecycle opdata tenants tenant admin deployments
deployment_id SystemAdminTenantIdisrv1
vm_group isrv1
name SystemAdminTena_isrv1_0_72619ffd-df8e-4c32-b24a-3d7b03a31303
SystemAdminTena_isrv1_0_72619ffd-df8e-4c32-b24a-3d7b03a31303 VM_ALIVE_STATE
nfvis# show vm_lifecycle opdata tenants tenant admin deployments vm_group isrv1
deployments isrv1 - -
vm_group isrv1
vm_instance 57b9a63a-9c9d-4765-baa6-2d7086ad3262
name SystemAdminTena_isrv1_0_72619ffd-df8e-4c32-b24a-3d7b03a31303
host_id NFVIS
hostname nfvis
interfaces interface 0
model virtio
port_id vnic1
network int-mgmt-net
subnet N/A
ip_address 192.0.2.10
mac_address 52:54:00:f1:5f:d9
netmask 255.255.255.0
gateway 192.0.2.1
interfaces interface 1
model virtio
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
74
VM Lifecycle Management Commands
show vm_lifecycle opdata
port_id vnic7
network wan-net
subnet N/A
mac_address 52:54:00:2b:41:e9
interfaces interface 2
model virtio
port_id vnic8
network lan-net
subnet N/A
mac_address 52:54:00:7a:27:25
netmask 255.255.255.0
gateway 198.51.100.1
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
75
VM Lifecycle Management Commands
show running-config vm_lifecycle
show running-config vm_lifecycle
To display the currently running VM life cycle configuration, use the show running-config vm_lifecycle
command in privileged EXEC mode.
show running-config vm_lifecycle
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show running-config vm_lifecycle
vm_lifecycle tenants tenant admin
description "Built-in Admin Tenant"
managed_resource false
vim_mapping true
!
vm_lifecycle networks network int-mgmt-net
subnet int-mgmt-net-subnet
ipversion ipv4
dhcp false
address 192.0.2.0
netmask 255.255.255.0
gateway 192.0.2.1
!
!
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
76
VM Lifecycle Management Commands
show running-config vm_packages
show running-config vm_packages
To display the running VM package configuration, use the show running-config vm_packages command
in privileged EXEC mode.
show running-config vm_packages
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show running-config vm_packages
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
77
VM Lifecycle Management Commands
show running-config vm_packages
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
78
Internal Management IP Commands
• vm_lifecycle networks, on page 80
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
79
Internal Management IP Commands
vm_lifecycle networks
vm_lifecycle networks
To create a new subnet, use the vm_lifecycle networks command in global configuration mode. To delete
an existing subnet, use the no form of this command.
vm_lifecycle networks network int-mgmt-net subnet int-mgmt-net-subnet address ip-address
gateway gateway-ip-address netmask netmask dhcp {true | false}
Syntax Description network int-mgmt-net Specifies the network name. The network name must be set to int-mgmt-net.
subnet int-mgmt-net-subnet Specifies the management subnet name. The subnet name must be set to
int-mgmt-net-subnet.
address ip-address Specifies the subnet address for the network.
gateway gateway-ip-address Specifies the gateway IP address for the network.
netmask netmask Specifies the netmask for the network.
dhcp Configures DHCP. The DHCP value must be set to false. The default value
is true.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 This command was introduced.
Usage Guidelines The management subnet should be changed before deploying any VMs. You must first delete the subnet and
then add the new subnet.
The chosen subnet should have at least four IP addresses for network, broadcast, gateway and VM. If the
monitoring IP is passed in the deployment payload, it should be within the IP addresses available in the address
pool. Otherwise, the Cisco Enterprise NFVIS assigns the next available IP from the address pool.
Example
nfvis(config)# vm_lifecycle networks network int-mgmt-net subnet int-mgmt-net-subnet address
192.168.0.0 gateway 192.168.0.1 netmask 255.255.255.0 dhcp false
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
80
System Monitoring Commands
• hostaction mgmt-dhcp-renew, on page 82
• hostaction wan-dhcp-renew, on page 83
• hostaction reboot, on page 84
• hostaction shutdown, on page 85
• show resources cpu-info allocation, on page 86
• show resources cpu-info cpus, on page 87
• show resources cpu-info vnfs, on page 88
• show resources precheck vnf, on page 89
• show system-monitoring host cpu, on page 90
• show system-monitoring host disk, on page 92
• show system-monitoring host memory, on page 94
• show system-monitoring host port, on page 96
• show system-monitoring vnf vcpu, on page 98
• show system-monitoring vnf disk, on page 99
• show system-monitoring vnf memory, on page 101
• show system-monitoring vnf port, on page 103
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
81
System Monitoring Commands
hostaction mgmt-dhcp-renew
hostaction mgmt-dhcp-renew
To renew the DHCP IP address on the management interface, use the hostaction mgmt-dhcp-renew command
in privileged EXEC mode.
hostaction mgmt-dhcp-renew
Syntax Description This command has no arguments or keywords.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following command renews the DHCP IP address on the management interface:
nfvis# hostaction mgmt-dhcp-renew
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
82
System Monitoring Commands
hostaction wan-dhcp-renew
hostaction wan-dhcp-renew
To renew the DHCP IP address on the WAN interface, use the hostaction wan-dhcp-renew command in
privileged EXEC mode.
hostaction wan-dhcp-renew
Syntax Description This command has no arguments or keywords.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following command renews the DHCP IP address on the WAN interface:
nfvis# hostaction wan-dhcp-renew
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
83
System Monitoring Commands
hostaction reboot
hostaction reboot
To reboot the Cisco NFVIS host, use the hostaction reboot command in privileged EXEC mode.
hostaction reboot
Syntax Description This command has no arguments or keywords.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines When you run this command, the connectivity is lost and the Cisco NFVIS host is rebooted. After the reboot
is complete, you can again connect to the Cisco NFVIS host.
Example
nfvis# hostaction reboot
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
84
System Monitoring Commands
hostaction shutdown
hostaction shutdown
To shut down the Cisco NFVIS host, use the hostaction shutdown command in privileged EXEC mode.
hostaction shutdown
Syntax Description This command has no arguments or keywords.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines After shutting down the Cisco NFVIS host, if you want to power it on again, use CIMC.
Example
nfvis# hostaction shutdown
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
85
System Monitoring Commands
show resources cpu-info allocation
show resources cpu-info allocation
To get information on the number of CPUs allocated to VMs and the CPUs that are already used by the VMs,
use the show resources cpu-info allocation command in privileged EXEC mode.
show resources cpu-info allocation [total-sockets | cores-per-socket | logical-cpus-used-by-system
| logical-cpus-used-by-vnfs | logical-cpus-used-dedicated | logical-cpus-used-sharable |
total-logical-cpus]
Syntax Description total-sockets (Optional) Total sockets allocated.
cores-per-socket (Optional) Number of cores per socket.
logical-cpus-used-by-system (Optional) Number of CPUs used by the system.
logical-cpus-used-dedicated (Optional) Number of dedicated CPUs.
total-logical-cpus (Optional) Total number of CPUs.
logical-cpus-used-by-vnfs (Optional) Number of CPUs used by VNFs.
Command Default Complete information about CPU allocation to VMs.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following is the sample output from the show resources cpu-info allocation command:
nfvis# show resources cpu-info allocation
resources cpu-info allocation total-sockets 1
resources cpu-info allocation cores-per-socket 8
resources cpu-info allocation total-logical-cpus 16
resources cpu-info allocation logical-cpus-used-by-system 2
resources cpu-info allocation logical-cpus-used-by-vnfs 14
resources cpu-info allocation logical-cpus-used-dedicated 12
resources cpu-info allocation logical-cpus-used-sharable 2
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
86
System Monitoring Commands
show resources cpu-info cpus
show resources cpu-info cpus
To display information on the VMs running in all the physical CPUs or a specific physical CPU in the system,
use the show resources cpu-info cpus command in privileged EXEC mode.
show resources cpu-info cpus [cpu cpu-id]
Syntax Description cpu cpu-id (Optional) The ID of the physical CPU.
Command Default Display information on the VMs running in all the physical CPUs.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following is a sample output from the show resources cpu-info cpus cpu 7 command:
nfvis# show resources cpu-info cpus cpu 7
CPU SOCKET CORE SYSTEM LOW VCPU
ID ID ID USE NAME VCPUS LATENCY ID
-----------------------------------------------------------------------
7 0 7 false 1471588629.ROUTER3 4 true 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
87
System Monitoring Commands
show resources cpu-info vnfs
show resources cpu-info vnfs
To display information on the CPUs and VCPUs that are allocated to each of the VMs, or a specific VM in
the system, use the show resources cpu-info vnfs command in privileged EXEC mode.
show resources cpu-info vnfs [vnf vnf-name]
Syntax Description vnf vnf-name (Optional) The name of the vnf.
Command Default Display information on the CPUs and VCPUs that are allocated to each of the VMs.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following is the sample output from the show resources cpu-info vnfs vnf
1472148662.ROUTER2 command:
nfvis# show resources cpu-info vnfs vnf 1472148662.ROUTER2
LOW VCPU SOCKET CORE CPU
NAME VCPUS LATENCY ID ID ID ID
-------------------------------------------------------------------------------------------------
1472148662.ROUTER2 2 true 0 0 3 3
0 3 11
0 2 10
Note In the example, when low latency is true, no VCPUs are assigned to this VM; instead CPUs 3, 11
and 10 are entirely reserved for this VM.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
88
System Monitoring Commands
show resources precheck vnf
show resources precheck vnf
To check if there are sufficient resources for the deployment of a new VM or for updating a deployed VM,
use the show resources precheck vnf in privileged EXEC mode.
show resources precheck vnf {vm-name flavor-name low-latency {true | false}}
Syntax Description vm-name The name of the VM. For updating an existing VM, the VM name must be
deployment-name.vm-group-name
flavor-name The name of the flavor.
low-latency This can be either true or false. If true, the VM needs dedicated CPUs.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
The following is a sample output from the show resources precheck vnf newvnf csr1kv-medium
true command:
nfvis# show resources precheck vnf newvnf csr1kv-medium true
VNF SUFFICIENT
NAME FLAVOR NAME LOW LATENCY RESOURCES CAUSE
-----------------------------------------------------------------------------
newvnf isr1kv-medium true false No enough CPU resources
The table below describes the significant fields shown in the display:
Table 2: show resources precheck Field Description
Field Description
VNF Name Name of the VM
Flavor Name The flavor name of the VM.
Low Latency If true, the VM needs dedicated CPUs.
Sufficient Resources Sufficient resources to deploy the VM.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
89
System Monitoring Commands
show system-monitoring host cpu
show system-monitoring host cpu
To display the host CPU statistics, use the show system-monitoring host cpu command in privileged EXEC
mode.
show system-monitoring host cpu [{stats | table} [cpu-usage duration [state state]]]
Syntax Description stats Displays the CPU statistics.
table Displays brief CPU statistics.
cpu-usage duration Specifies the statistics duration. Valid values are 1min, 5min, 15min, 30min, 1h, 6h,
1d, 5d, and 30d. Default duration is 5min.
state state Specifies the CPU state. Valid states are non-idle, interrupt, nice, system, user, and
wait . Default state is non-idle.
This parameter is available only with stats parameter.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system-monitoring host cpu stats
system-monitoring host cpu stats cpu-usage 5min state non-idle
collect-start-date-time 2017-03-20T08:58:40-00:00
collect-interval-seconds 10
cpu
id 0
usage-percentage "[2.11, 3.64, 1.12, 1.29, 1.16, 0.83, 1.14, 1.7, 3.27, 2.06, 2.43, 1.8,
2.52, 1.63, 1.85, 1.53, 3.38, 2.2, 2.08,
1.74, 1.25, 1.69, 1.6, 1.51, 1.63, 1.85]"
cpu
id 1
usage-percentage "[0.47, 0.2, 0.23, 0.47, 0.21, 0.32, 0.47, 0.2, 0.23, 0.48, 0.29, 0.25,
0.65, 0.2, 0.23, 0.47, 0.21, 0.32, 0.46,
0.13, 0.41, 0.48, 0.3, 0.33, 0.55, 0.11, 0.23]"
cpu
id 2
usage-percentage "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0]"
...
nfvis# show system-monitoring host cpu table
MIN MAX AVERAGE
DURATION ID STATE PERCENTAGE PERCENTAGE PERCENTAGE
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
90
System Monitoring Commands
show system-monitoring host cpu
-------------------------------------------------------------
5min 0 non-idle 1.25 3.38 1.93
interrupt 0.0 0.0 0.0
nice 0.0 0.0 0.0
softirq 0.0 0.09 0.0
steal 0.0 0.0 0.0
system 0.43 1.68 0.78
user 0.34 0.86 0.6
wait 0.0 1.86 0.58
1 non-idle 0.11 0.65 0.34
interrupt 0.0 0.0 0.0
nice 0.0 0.0 0.0
softirq 0.0 0.01 0.0
steal 0.0 0.0 0.0
system 0.01 0.28 0.14
user 0.02 0.37 0.19
wait 0.0 0.0 0.0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
91
System Monitoring Commands
show system-monitoring host disk
show system-monitoring host disk
To display the statistics about the host disk, use the show system-monitoring host disk command in privileged
EXEC mode.
show system-monitoring host disk stats [{disk-operations | disk-space} duration
[{collect-interval-seconds | collect-start-date-time | disk | mount-point}]]
Syntax Description stats Displays the disk statistics.
disk-operations Displays the disk operation statistics.
disk-space Displays the disk space statistics.
duration Specifies the statistics duration. Valid values are 1min, 5min, 15min, 30min, 1h,
6h, 1d, 5d, and 30d. Default duration is 5min.
collect-interval-seconds Displays the collection interval in seconds.
collect-start-date-time Displays the statistics by the start date and time of data collection.
disk Displays the disk statistics by disk name. This parameter is available only with
disk-operations parameter.
mount-point Displays the disk statistics by mount name. This parameter is available only with
disk-space parameter.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system-monitoring host disk stats disk-operations 1min
system-monitoring host disk stats disk-operations 1min
collect-start-date-time 2017-03-20T09:24:20-00:00
collect-interval-seconds 10
disk
name disk-sda
io-time-ms [54.11, 62.98]
io-time-weighted-ms [4990.48, 6232.35]
merged-reads-per-sec [0.0]
merged-writes-per-sec [4.77]
bytes-read-per-sec [0.0]
bytes-written-per-sec [202506.24]
reads-per-sec [0.0, 0.0]
writes-per-sec [38.68, 40.05]
time-per-read-ms []
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
92
System Monitoring Commands
show system-monitoring host disk
time-per-write-ms []
pending-ops [0.0, 0.0, 0.0]
...
nfvis# show system-monitoring host disk stats disk-space 5min
system-monitoring host disk stats disk-space 5min
collect-start-date-time 2017-03-20T09:27:30-00:00
collect-interval-seconds 10
mount-point
name /boot
free-GB "[0.33, 0.33, 0.33, 0.33, 0.33, 0.33, 0.33, 0.33, 0.33, 0.33, 0.33, 0.33, 0.33,
0.33, 0.33, 0.33, 0.33, 0.33, 0.33, 0.33,
0.33, 0.33, 0.33]"
used-GB "[0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1,
0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1, 0.1,
0.1, 0.1]"
reserved-GB "[0.03, 0.03, 0.03, 0.03, 0.03, 0.03, 0.03, 0.03, 0.03, 0.03, 0.03, 0.03, 0.03,
0.03, 0.03, 0.03, 0.03, 0.03, 0.03,
0.03, 0.03, 0.03, 0.03]"
mount-point
name /data
free-GB "[844.0, 844.0, 844.0, 844.0, 844.0, 844.0, 844.0, 844.0, 844.0, 844.0, 844.0,
844.0, 844.0, 844.0, 844.0, 844.0, 844.0,
844.0, 844.0, 844.0, 844.0, 844.0, 844.0, 844.0, 844.0]"
used-GB "[6.48, 6.48, 6.48, 6.48, 6.48, 6.48, 6.48, 6.48, 6.48, 6.48, 6.48, 6.48, 6.48,
6.48, 6.48, 6.48, 6.48, 6.48, 6.48, 6.48,
6.48, 6.48, 6.48]"
reserved-GB "[45.54, 45.54, 45.54, 45.54, 45.54, 45.54, 45.54, 45.54, 45.54, 45.54, 45.54,
45.54, 45.54, 45.54, 45.54, 45.54,
45.54, 45.54, 45.54, 45.54, 45.54, 45.54, 45.54, 45.54, 45.54, 45.54, 45.54]"
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
93
System Monitoring Commands
show system-monitoring host memory
show system-monitoring host memory
To display the statistics about the host memory, use the show system-monitoring host memory command
in privileged EXEC mode.
show system-monitoring host memory [{stats | table} [mem-usage duration]]
Syntax Description stats Displays detailed memory statistics.
table Displays brief memory statistics.
mem-usage duration Specifies the statistics duration. Valid values are 1min, 5min, 15min, 30min, 1h, 6h,
1d, 5d, and 30d. Default duration is 5min.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system-monitoring host memory stats
system-monitoring host memory stats mem-usage 5min
collect-start-date-time 2017-03-20T09:29:40-00:00
collect-interval-seconds 10
buffered-MB "[261.65, 261.67, 261.69, 261.7, 261.71, 261.72, 261.74, 261.75, 261.75, 261.76,
261.78, 261.78, 261.79, 261.79,
261.8, 261.8, 261.81, 261.82, 261.82, 261.83, 261.84, 261.84, 261.85, 261.85, 261.86,
261.86, 261.86, 261.86]"
cached-MB "[7191.49, 7191.49, 7191.5, 7191.5, 7191.51, 7191.5, 7191.51, 7191.5, 7191.51,
7191.51, 7191.5, 7191.51,
7191.51, 7191.51, 7191.51, 7191.51, 7191.51, 7191.51, 7191.51, 7191.51, 7191.51, 7191.51,
7191.51, 7191.51, 7191.51,
7191.51, 7191.51]"
free-MB "[45447.74, 45447.77, 45447.96, 45447.97, 45447.79, 45447.46, 45447.37, 45447.6,
45447.76, 45447.66, 45447.97,
45447.39, 45446.85, 45446.71, 45447.98, 45447.98, 45448.18, 45446.67, 45448.17, 45447.94,
45448.23, 45447.61, 45447.74,
45447.58, 45448.39, 45448.02, 45448.05, 45448.02]"
used-MB "[10909.11, 10908.99, 10908.7, 10908.71, 10908.85, 10909.15, 10909.13, 10909.09,
10908.87, 10908.84, 10908.64,
10909.14, 10909.76, 10909.85, 10908.65, 10908.65, 10908.46, 10909.86, 10908.41, 10908.59,
10908.32, 10908.83, 10908.75,
10909.0, 10908.17, 10908.6, 10908.6, 10908.58]"
slab-recl-MB "[295.25, 295.25, 295.25, 295.25, 295.25, 295.25, 295.25, 295.25, 295.25,
295.25, 295.26, 295.26, 295.26,
295.27, 295.27, 295.27, 295.27, 295.27, 295.27, 295.27, 295.27, 295.27, 295.27]"
slab-unrecl-MB "[57.19, 57.26, 57.32, 57.29, 57.32, 57.33, 57.42, 57.23, 57.27, 57.4,
57.28, 57.35, 57.25, 57.3, 57.21,
57.21, 57.2, 57.3, 57.25, 57.3, 57.26, 57.36, 57.3, 57.22, 57.24, 57.16, 57.14, 57.18,
57.28]"
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
94
System Monitoring Commands
show system-monitoring host memory
nfvis# show system-monitoring host memory table mem-usage 1min
MIN MAX AVERAGE
DURATION TYPE MIN MAX AVERAGE
---------------------------------------------------
1min buffered-MB 0 0 0
cached-MB 0 0 0
free-MB 0 0 0
slab-recl-MB 295.27 295.27 295.27
slab-unrecl-MB 57.28 57.28 57.28
used-MB 0 0 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
95
System Monitoring Commands
show system-monitoring host port
show system-monitoring host port
To display the statistics about the host ports, use the show system-monitoring host port command in privileged
EXEC mode.
show system-monitoring host port [{stats | table} [port-usage duration]]
Syntax Description stats Displays detailed port statistics.
table Displays brief port statistics.
port-usage duration Specifies the statistics duration. Valid values are 1min, 5min, 15min, 30min, 1h, 6h,
1d, 5d, and 30d. Default duration is 5min.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Examples
nfvis# show system-monitoring host port stats
system-monitoring host port stats port-usage 5min
collect-start-date-time 2017-03-20T09:42:30-00:00
collect-interval-seconds 10
port
name eth0
total-packets-per-sec "[36.82, 20.43, 17.25, 18.49, 17.55, 18.05, 18.42, 18.48, 24.75,
18.73, 27.23, 42.25, 20.83, 18.28, 17.66,
21.24, 16.68, 20.95, 21.01, 25.17, 20.79, 20.47, 55.73]"
rx-packets-per-sec "[36.28, 20.43, 17.22, 18.2, 17.36, 17.93, 18.15, 18.47, 24.64, 18.53,
27.01, 41.87, 20.65, 18.26, 17.47,
21.13, 16.48, 20.75, 20.83, 25.14, 20.52, 19.84, 49.61]"
tx-packets-per-sec "[0.54, 0.0, 0.03, 0.29, 0.19, 0.12, 0.27, 0.01, 0.11, 0.2, 0.22, 0.38,
0.18, 0.02, 0.19, 0.11, 0.2, 0.2,
0.18, 0.03, 0.27, 0.63, 6.12]"
total-errors-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0]"
rx-errors-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0]"
tx-errors-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0]"
...
nfvis# show system-monitoring host port table
URATION NAME COLLECT START DATE TIME SECONDS STATUS ADDRESS PACKETS PACKETS PER SEC PER SEC
----------------------------------------------------------------------------------------------------------
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
96
System Monitoring Commands
show system-monitoring host port
5min eth0 2017-03-20T09:44:10-00:00 10 up NA 4814 55 16.6 0.19
5min eth1 2017-03-20T09:44:10-00:00 10 up NA 5330 5 18.38 0.02
5min eth2 2017-03-20T09:44:10-00:00 10 down NA 0 0 0.0 0.0
5min eth3 2017-03-20T09:44:10-00:00 10 down NA 0 0 0.0 0.0
5min eth4 2017-03-20T09:44:10-00:00 10 down NA 0 0 0.0 0.0
5min eth5 2017-03-20T09:44:10-00:00 10 down NA 0 0 0.0 0.0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
97
System Monitoring Commands
show system-monitoring vnf vcpu
show system-monitoring vnf vcpu
To display the CPU statistics for VNFs running on the host, use the show system-monitoring vnf vcpu
command in privileged EXEC mode.
show system-monitoring vnf vcpu stats [vcpu-usage duration]
Syntax Description stats Displays the VNF CPU statistics.
vcpu-usage duration Specifies the statistics duration. Valid values are 1min, 5min, 15min, 30min, 1h, 6h,
1d, 5d, and 30d. Default duration is 5min.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system-monitoring vnf vcpu stats
system-monitoring vnf vcpu stats vcpu-usage 5min
vnf ISRv
collect-start-date-time 2017-03-20T06:49:50-00:00
collect-interval-seconds 10
total-percentage "[55.05, 65.35, 73.35, 70.23, 58.28, 52.08, 52.23, 53.05, 52.88, 53.23,
56.28, 58.45, 54.85, 55.05, 60.03,
54.18, 33.33, 16.9, 13.33, 12.15, 12.2, 12.13, 12.0, 12.8, 12.83, 11.98, 11.98]"
vcpu
id 0
vcpu-percentage "[94.55, 75.35, 66.75, 78.7, 92.8, 100.0, 100.0, 100.0, 100.0, 100.0,
100.0, 99.85, 91.25, 86.45, 83.4, 72.8,
41.0, 9.3, 5.05, 4.8, 4.85, 4.65, 4.7, 4.95, 4.85, 4.65, 4.7, 4.6, 4.95]"
vcpu
id 1
vcpu-percentage "[14.2, 53.65, 78.25, 59.7, 22.9, 3.75, 4.0, 5.8, 5.6, 6.2, 12.3, 16.35,
17.1, 16.75, 19.5, 23.15, 22.05, 22.3,
21.45, 19.45, 19.55, 19.55]"
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
98
System Monitoring Commands
show system-monitoring vnf disk
show system-monitoring vnf disk
To display the disk statistics for VNFs running on the host, use the show system-monitoring vnf disk
command in privileged EXEC mode.
show system-monitoring vnf disk stats [disk-operations duration]
Syntax Description stats Displays the VNF disk statistics.
disk-operations duration Specifies the statistics duration. Valid values are 1min, 5min, 15min, 30min,
1h, 6h, 1d, 5d, and 30d. Default duration is 5min.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system-monitoring vnf disk stats
system-monitoring vnf disk stats disk-operations 5min
vnf 1489446885.ROUTER
collect-start-date-time 2017-03-20T09:55:30-00:00
collect-interval-seconds 10
disk
disk-name vda
bytes-read-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0]"
bytes-written-per-sec "[92.16, 696.32, 6266.88, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 204.8, 1843.2, 0.0, 40.96, 368.64,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 30.72]"
reads-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0]"
writes-per-sec "[0.09, 0.08, 0.72, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.03, 0.27,
0.0, 0.01, 0.09, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.03, 0.27]"
disk
disk-name hdd
bytes-read-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0]"
bytes-written-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0]"
reads-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0]"
writes-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
99
System Monitoring Commands
show system-monitoring vnf disk
0.0, 0.0, 0.0, 0.0, 0.0]"
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
100
System Monitoring Commands
show system-monitoring vnf memory
show system-monitoring vnf memory
To display the memory statistics for VNFs running on the host, use the show system-monitoring vnf memory
command in privileged EXEC mode.
show system-monitoring vnf memory stats [mem-usage duration]
Syntax Description stats Displays the VNF memory statistics.
mem-usage duration Specifies the statistics duration. Valid values are 1min, 5min, 15min, 30min, 1h, 6h,
1d, 5d, and 30d. Default duration is 5min.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system-monitoring vnf memory stats
system-monitoring vnf memory stats mem-usage 5min
vnf 1489446885.ROUTER
collect-start-date-time 2017-03-20T09:53:20-00:00
collect-interval-seconds 10
total-MB "[4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0,
4096.0, 4096.0, 4096.0, 4096.0,
4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0]"
rss-MB "[4175.93, 4175.93, 4175.93, 4175.93, 4175.93, 4175.93, 4175.93, 4175.93, 4175.93,
4175.93, 4175.93, 4175.93, 4175.93,
4175.93, 4176.13, 4177.73, 4175.95, 4175.95, 4175.95, 4175.95, 4175.95, 4175.95, 4175.95,
4175.95, 4175.95, 4175.95, 4175.95,
4175.95]"
vnf 1489448227.OTHER
collect-start-date-time 2017-03-20T09:53:20-00:00
collect-interval-seconds 10
total-MB "[256.0, 256.0, 256.0, 256.0, 256.0, 256.0, 256.0, 256.0, 256.0, 256.0, 256.0,
256.0, 256.0, 256.0, 256.0, 256.0, 256.0,
256.0, 256.0, 256.0, 256.0, 256.0, 256.0, 256.0]"
rss-MB "[113.66, 113.66, 113.66, 113.66, 113.66, 113.66, 113.66, 113.66, 113.66, 113.66,
113.66, 113.66, 113.66, 113.66, 113.66,
113.66, 113.66, 113.66, 113.66, 113.66, 113.66, 113.66, 113.66, 113.66, 113.66, 113.66,
113.66, 113.66, 113.66]"
vnf 1489532063.ROUTER2
collect-start-date-time 2017-03-20T09:53:20-00:00
collect-interval-seconds 10
total-MB "[4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0,
4096.0, 4096.0, 4096.0, 4096.0,
4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0, 4096.0]"
rss-MB "[4147.98, 4147.98, 4147.98, 4147.98, 4147.98, 4147.98, 4147.98, 4147.98, 4147.98,
4147.98, 4147.98, 4147.98, 4147.98,
4147.98, 4147.98, 4147.98, 4147.98, 4147.98, 4147.98, 4147.98, 4147.96, 4147.96, 4147.96,
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
101
System Monitoring Commands
show system-monitoring vnf memory
4147.96, 4147.96]"
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
102
System Monitoring Commands
show system-monitoring vnf port
show system-monitoring vnf port
To display the port statistics for VNFs running on the host, use the show system-monitoring vnf port
command in privileged EXEC mode.
show system-monitoring vnf port stats [port-usage duration]
Syntax Description stats Displays the VNF port statistics.
port-usage duration Specifies the statistics duration. Valid values are 1min, 5min, 15min, 30min, 1h, 6h,
1d, 5d, and 30d. Default duration is 5min.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system-monitoring vnf port stats
system-monitoring vnf port stats port-usage 5min
vnf 1489446885.ROUTER
collect-start-date-time 2017-03-20T09:56:50-00:00
collect-interval-seconds 10
port
port-name vnic0
total-packets-per-sec "[0.78, 0.62, 0.8, 0.78, 0.64, 0.96, 0.6, 0.64, 0.96, 0.6, 0.64,
0.96, 0.62, 0.8, 0.78, 0.62, 0.8, 0.78,
0.62, 0.8, 0.78, 0.62, 0.81, 0.89]"
rx-packets-per-sec "[0.39, 0.31, 0.4, 0.39, 0.32, 0.48, 0.3, 0.32, 0.48, 0.3, 0.32, 0.48,
0.31, 0.4, 0.39, 0.31, 0.4, 0.39, 0.31,
0.4, 0.39, 0.31, 0.4, 0.4]"
tx-packets-per-sec "[0.39, 0.31, 0.4, 0.39, 0.32, 0.48, 0.3, 0.32, 0.48, 0.3, 0.32, 0.48,
0.31, 0.4, 0.39, 0.31, 0.4, 0.39, 0.31,
0.4, 0.39, 0.31, 0.41, 0.49]"
total-errors-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0]"
rx-errors-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0]"
tx-errors-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0]"
port
port-name vnic1
total-packets-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0]"
rx-packets-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
103
System Monitoring Commands
show system-monitoring vnf port
0.0, 0.0, 0.0, 0.0]"
tx-packets-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0]"
total-errors-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0]"
rx-errors-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0]"
tx-errors-per-sec "[0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0, 0.0]"
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
104
System Operations Commands
• scp, on page 106
• system file-copy usb, on page 109
• system file-download file, on page 110
• system file-delete, on page 111
• system usb-mount, on page 112
• telnet, on page 113
• show system file-list, on page 114
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
105
System Operations Commands
scp
scp
To secure copy a file from the Cisco NFVIS to an external system or from an external system to Cisco NFVIS,
the admin user can use the scp command in privileged EXEC mode.
For detailed information about how to use this command to copy to or from supported locations, see the Usage
Guidelines section.
scp source destination
Syntax Description source To copy a file from an external system, specify the source in the following format:
user@remotehostip:file.
To copy a file to an external system, specify the NFVIS location and name of the file.
The external host can have an IPv4 or IPv6 address as described in the Usage Guidelines
section.
destination To copy a file to an external system, specify the the destination in the following format:
user@remotehostip:file.
To copy a file from an external system, specify the NFVIS location and name of the file.
The external host can have an IPv4 or IPv6 address as described in the Usage Guidelines
section.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 Support for IPv6 address, NFS location, USB, prefix mappings and log file copy was added.
3.6.1 This command was introduced.
Usage Guidelines Following are the guidelines for using the scp command:
• Supported Users: Only the admin user can run the scp command.
• Certain special characters are blacklisted from source and destination path, except in certain positions -
'*', '&', ';', ':', '@', '|', '..'
• Supported Locations
• The admin user can copy files to and from the intdatastore, extdatastore1,
extdatastore2, usb, and nfs locations in Cisco NFVIS. In addition, the admin user can copy
the log files from Cisco NFVIS to an external system.
Any attempt to SCP to NFVIS file system other than the mentioned list is prohibited by the command:
intdatastore - /data/intdatastore/uploads/
extdatastore1 - /mnt/extdatastore1/uploads/
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
106
System Operations Commands
scp
extdatastore2 - /mnt/extdatastore2/uploads/
usb - /mnt-usb/
nfs - /data/mount/
logs - /data/intdatastore/logs
You can copy to and from extdatastore1, extdatastore2, usb, and nfs locations only
if they are available or mounted. The extdatastore1 and extdatastore2 locations are
available only in the Cisco ENCS 5400 Series.
• The admin user can copy the log files from the logs folder of Cisco NFVIS to an external system.
Copying files to the logs folder is not allowed. All SCP actions are logged into
/data/intdatastore/logs/nfvis_scp.log file.
• To copy to or from a USB, you must first mount the USB by using the system usb-mount mount
ACTIVE command. After the USB is mounted, use the show system file-list disk usb command
to find the exact USB name and provide the identified USB name in the scp command; for example,
scpuser@remotehostip:fileusb:usb_name/filename.
• To copy to or from NFS, you must first mount an NFS location by using the system storage
nfs_storage command. After the NFS is mounted, you must specify the name of the NFS mount in
the scp command; for example, scp user@remotehostip:filenfs: mount_name/filename.
• Supported Address Types: You can specify IPv4 or IPv6 address of an external system. The IPv6 address
of the external system must be specified within square brackets ([ ]); for example, scp user@[
remotehostip]:sourcefile destinationfile
Example
The following example copies the sample.txt file from intdatastore to an external system.
nfvis# scp intdatastore:sample.txt [email protected]:/Users/user/Desktop/sample.txt
Example
The following example copies the test.txt file from an external system to intdatastore.
nfvis# scp [email protected]:/Users/user/Desktop/test.txt intdatastore:test_file.txt
Example
The following example copies the test.txt file from an external system to USB.
nfvis# scp [email protected]:/user/Desktop/my_test.txt usb:usb1/test.txt
Example
The following example copies the sample.txt file to an NFS location.
nfvis# scp [email protected]:/user/Desktop/sample.txt nfs:nfs_test/sample.txt
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
107
System Operations Commands
scp
Example
The following example copies the sample.txt file from an external system with IPv6 address.
nfvis# scp user@[2001:DB8:0:ABCD::1]:/user/Desktop/sample.txt intdatastore:sample.txt
Example
The following example copies the nfvis_scp.log file to an external system.
nfvis# scp logs:nfvis_scp.log [email protected]:/Users/user/Desktop/copied_nfvis_scp.log
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
108
System Operations Commands
system file-copy usb
system file-copy usb
To copy a VM image using the USB drive, use the system file-copy usb command in global configuration
mode.
system file-copy usb file name string
Syntax Description file name string Specifies the file name of the VM image.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
This command was
introduced.
Example
The following example shows how to copy a VM image using the USB drive:
nfvis(config)# system usb-mount mount active
nfvis(config)# system file-copy usb file name usb1/package/isrv-universalk9.16.03.01.tar.gz
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
109
System Operations Commands
system file-download file
system file-download file
To download a file to a specific location (/data/intdatastore/uploads) on the host server, from a HTTP server,
use the system file-download file command.
system file-download file { source http checksum sha256 checksum }
Syntax Description source Specifies the path for the file to be copied.
(Optional) checksum Specifies the SHA256 checksum for the file to be downloaded.
Command Default None
Command Modes None
Command History Release Modification
3.9.1 This command was
introduced.
Example
The following example shows how to download a file to a specific location (/data/intdatastore/uploads)
on the host server, from the HTTP server:
nfvis# system:system file-download file { source http://1.2.3.4/file_1 checksum
73f0474f9d145c8e2d89e9b3dda937676a52e854bc76c2da18738733503a0d83 }
Note Multiple files can be downloaded, either with or without checksum, at the same time.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
110
System Operations Commands
system file-delete
system file-delete
To delete a file from the default location (/data/intdatastore/uploads) on the host server, use the system
file-delete command in global configuration mode.
system file-delete file name string
Syntax Description name string Specifies the name of the
file.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example shows how to delete a file from the default location on the host server:
nfvis(config)# system file-delete file name /data/intdatastore/uploads/TinyLinux.tar.gz
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
111
System Operations Commands
system usb-mount
system usb-mount
To mount the USB drive on the NFVIS server, use the system usb-mount command in global configuration
mode. To unmount, use the no form of this command.
system usb-mount mount active
no system usb-mount
Syntax Description mount active Mounts the USB drive on the NFVIS server.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was
introduced.
Usage Guidelines Ensure that you have plugged the USB drive that contains the required images into the server before mounting
the USB drive.
Example
nfvis(config)# system usb-mount mount active
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
112
System Operations Commands
telnet
telnet
To open a telnet session to a local service on a serial port, use the telnet command in privileged EXEC mode.
telnet serial-port
Syntax Description serial-port Specifies the name of the serial port. The serial port must be enabled for the VM.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# telnet 7000
Trying 127.0.0.85...
Connected to 127.0.0.85.
Escape character is '^]'.
Router>
Router>
Router>?
Exec commands:
access-profile Apply user-profile to interface
app-hosting Application hosting
appnav IOS Wide Area Application Services
clear Reset functions
connect Open a terminal connection
crypto Encryption related commands.
disable Turn off privileged commands
disconnect Disconnect an existing network connection
do-exec Mode-independent "do-exec" prefix support
enable Turn on privileged commands
ethernet Ethernet parameters
exit Exit from the EXEC
help Description of the interactive help system
ip IP SLA Exec Command
lat Open a lat connection
license Smart licensing Commands
lig LISP Internet Groper
lock Lock the terminal
login Log in as a particular user
logout Exit from the EXEC
mrinfo Request neighbor and version information from a multicast
--More--
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
113
System Operations Commands
show system file-list
show system file-list
To display a list of system files, use the show system file-list command in privileged EXEC mode.
show system file-list [disk [{local | nfs | usb}]]
Syntax Description disk Displays files from the specified disk type.
local Displays the files on local system.
nfs Displays the files on NFS.
usb Displays the files on mounted USB drive.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system file-list
system file-list disk local 1
name nfvisvmpackagingtool.tar
path /data/intdatastore/uploads/vmpackagingutility
size 50K
type "VM Packaging Tool"
date-modified "2017-09-07 02:18:53"
system file-list disk local 2
name catalina.out-20171001.gz
path /data/intdatastore/logs/2017-10
size 40
type "Log File"
date-modified "2017-10-01 04:00:01"
system file-list disk local 3
name ovsdb-server.log-20171001.gz
path /data/intdatastore/logs/2017-10
size 276
type "Log File"
date-modified "2017-10-01 04:00:01"
system file-list disk local 4
name ovs-vswitchd.log-20171001.gz
path /data/intdatastore/logs/2017-10
size 204
type "Log File"
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
114
System Time Commands
• system time, on page 116
• system set-manual-time, on page 118
• show system time, on page 119
• show running-config system time, on page 120
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
115
System Time Commands
system time
system time
To set the system time using the Network Time Protocol (NTP) server, use the system time command in
global configuration mode. Use the no form of the command to delete the time configuration.
Note When you enable and synchronize the system time clock using an NTP server, you must reboot the Cisco
Enterprise NFVIS so that the BMC or CIMC date and time get updated with the new hardware clock.
system time [timezone zone-subzone] [ntp [preferred_server {ipv4-address host-name}]
[backup_server {ipv4-address host-name}] | ntp-ipv6 {ipv6-address host-name}]
no system time {ntp | ntp-ipv6}
Syntax Description timezone zone-subzone Specifies the timezone using zone and subzone.
ntp Specifies the time using the NTP IPv4 server.
preferred_server Specifies the IPv4 preferred server details.
ipv4-address Specifies the IPv4 address.
hostname Specifies the hostname.
backup_server Specifies the IPv4 backup server details.
ntp-ipv6 Specifies the time using the NTP IPv6 server.
ipv6-address Specifies the IPv6 address.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 The manual_time parameter is removed and the
ntp-ipv6 parameter is added.
To set the system time manually, use the system
set-manual-time command.
3.5.1 This command was introduced.
Usage Guidelines When you set the system time manually using the system set-manual-time command, the NTP is disabled
automatically. Similarly, when NTP is enabled, the manual time configuration is automatically disabled.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
116
System Time Commands
system time
Example
The following example shows how to set system time using NTP IPv4 server:
nfvis(config)# system time ntp preferred_server 198.51.100.1 backup_server 203.0.113.1
nfvis(config)# commit
Example
The following example shows how to set system time using NTP IPv6 server:
nfvis(config)# system time ntp-ipv6 2001:420:30d:201:ffff:ffff:fff4:35
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
117
System Time Commands
system set-manual-time
system set-manual-time
To set the system time clock manually, use the system set-manual-time command in privileged EXEC mode.
system set-manual-time date-time
Syntax Description date-time Specifies the manual date and time in YYYY-MM-DDTHH:MM:SS format. The supported year
range for specifying the manual time is from 2016 to 2036.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Usage Guidelines When you set the system time manually, the NTP is disabled automatically. Similarly, when NTP is enabled
using the system-time command, the manual time configuration is automatically disabled.
Example
nfvis# system set-manual-time 2017-01-01T17:35:39
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
118
System Time Commands
show system time
show system time
To view the system time clock configuration details, use the show system time command in privileged EXEC
mode.
show system time [current-time | current-timezone | ntp [status]]
Syntax Description current-time Displays the current system time.
current-timezone Displays the current system time zone.
ntp Displays the synchronization status of the NTP server.
status Displays the NTP status. You can filter the status using any of the following fields:
delay, jitter, offset, poll, reach, refid, st, t, or when.
Command Default All time configuration details are displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 The command was modified to include the
current-time, current-timezone, ntp, status parameters
and remove the backup-server, date, ntp-status,
preferred-server, and timezone parameters.
3.5.1 This command was introduced.
Usage Guidelines If the configured NTP server is not displayed in the command output, check that the NTP server is configured
correctly.
When a remote host is queried, if the response is not received before the timeout time, the request times out
and the information is not displayed in the command output.
Example
The following is a sample output of the show system time ntp status command:
nfvis# show system time ntp status
REMOTE REFID ST T WHEN POLL REACH DELAY OFFSET JITTER
==========================================================================================
*2001:420:30d:20 .GPS. 2 u 35 64 377 0.927 6.551 1.319
* sys.peer and synced, o pps.peer, # selected, + candidate,
- outlyer, . excess, x falseticker, space reject
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
119
System Time Commands
show running-config system time
show running-config system time
To display the running system time configuration, use the show running-config system time command in
privileged EXEC mode.
show running-config system time
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show running-config system time
system time ntp preferred_server 1.2.3.4
system time ntp backup_server 10.2.2.2
system time timezone America/New_York
system time ntp-ipv6 2001:420:30d:201:ffff:ffff:fff4:35
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
120
System Portal Commands
• system portal access, on page 122
• show system portal status, on page 123
• show running-config system portal access, on page 124
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
121
System Portal Commands
system portal access
system portal access
To enable or disable the Cisco Enterprise NFVIS portal access, use the system portal access command in
global configuration mode.
system portal access {enable | disable}
Syntax Description enable Enables the portal access.
disable Disables the portal access.
Command Default Portal access is enabled by default.
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following example shows how to disable the portal access:
nfvis(config)# system portal access disable
nfvis(config)# commit
nfvis(config)# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
122
System Portal Commands
show system portal status
show system portal status
To verify the Cisco Enterprise NFVIS portal access status, use the show system portal statuscommand in
privileged EXEC mode.
show system portal status
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following is a sample output of the show system portal status command:
nfvis# show system portal status
system portal status "access disabled"
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
123
System Portal Commands
show running-config system portal access
show running-config system portal access
To display the running configuration for the Cisco Enterprise NFVIS portal access, use the show running-config
system portal access command in privileged EXEC mode.
show running-config system portal access
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show running-config system portal access
system portal access enabled
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
124
System Routes Commands
• system routes route, on page 126
• show system routes, on page 127
• show system dhcp-routes, on page 128
• show running-config system routes, on page 129
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
125
System Routes Commands
system routes route
system routes route
To create a new system route or to modify an existing system route, use the system routes route command
in global configuration mode. To delete a system route, use the no form of the command.
system routes route destination prefix-length [gateway gateway] [dev device]
no system routes route destination prefix-length
Syntax Description destination The route destination address.
prefix-length The netmask for the destination address.
gateway gateway (Optional) The gateway for the route.
dev device (Optional) The device interface that the route will use.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines Though only the destination and prefix length are mandatory parameters for creating a route, a valid route
requires that you specify the gateway or the interface or both.
Example
The following command creates a system route to the destination 203.0.113.1:
nfvis(config)# system routes route 203.0.113.1 12 dev lan-br
nfvis(config)# commit
nfvis(config)# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
126
System Routes Commands
show system routes
show system routes
To display the list of system routes, use the show system routes command in privileged EXEC mode.
show system routes [route route-name]
Syntax Description route route-name (Optional) Name of the process.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following is a sample output from the show system routes command:
nfvis# show system routes
DESTINATION PREFIXLEN STATUS
----------------------------------
203.0.113.1 12 -
203.0.113.2 12 -
203.0.113.3 24 -
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
127
System Routes Commands
show system dhcp-routes
show system dhcp-routes
To display the DHCP static routes, use the show system dhcp-routes command in privileged EXEC mode.
show system dhcp-routes
Syntax Description This command has no arguments or keywords.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show system dhcp-routes
DESTINATION PREFIXLEN GATEWAY DEV
--------------------------------------------------------------------------
192.0.2.0 16 203.0.113.0 wan-br
192.0.2.213 32 203.0.113.0 wan-br
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
128
System Routes Commands
show running-config system routes
show running-config system routes
To display the running configuration of system routes, use the show running-config system routes command
in privileged EXEC mode.
show running-config system routes [route route-name]
Syntax Description route route-name (Optional) Name of the process.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show running-config system routes
DESTINATION PREFIXLEN STATUS
----------------------------------
203.0.113.1 12 -
203.0.113.2 12 -
203.0.113.3 24 -
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
129
System Routes Commands
show running-config system routes
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
130
System Log Commands
• system set-log , on page 132
• show system logging-level, on page 133
• show log, on page 134
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
131
System Log Commands
system set-log
system set-log
To set the log level and log type of messages, use the system set-log command in privileged EXEC mode.
system set-log level {debug | info | warning | error | critical} logtype {configuration | operational
| all}
Syntax Description level Specifies the log level.
debug Logs all messages.
info Logs all messages that have info and higher severity level.
warning Logs all messages that have warning and higher severity level.
error Logs all messages that have error and higher severity level.
critical Logs all messages that have critical severity level.
logtype Specifies the log type.
configuration Configuration log messages are recorded.
operational Operational log messages are recorded.
all All types of log messages are recorded.
Command Default For the configuration log, info is the default level. For the operational log, warning is the default level.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines After a system reboot, the modified logging configuration is reset to the default level, that is, info for the
configuration log and warning for the operational log.
Example
The following example shows how to configure a log level:
nfvis# system set-log level error logtype all
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
132
System Log Commands
show system logging-level
show system logging-level
To view the log level and log type settings, use the show system logging-level command in privileged EXEC
mode.
show system logging-level [{configuration | operational}]
Syntax Description configuration (Optional) Log level for the configuration log type is displayed.
operational (Optional) Log level for the operational log type is displayed.
Command Default The log level for all log types is displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following is a sample output of the show system logging-level command with the default log
level settings:
nfvis# show system logging-level
system logging-level configuration info
system logging-level operational warning
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
133
System Log Commands
show log
show log
To display a list of available log files or content of a specific log file, use the show log command in privileged
EXEC mode.
show log log-name
Syntax Description log-name Specifies the log file name. The log file name should be same as shown in the output of the show
log command.
Command Default None
Command Modes Privileged EXEC mode
Command History Release Modification
3.7.1 The log-name parameter is an optional parameter.
When this parameter is not specified, a listing of all
available log files is displayed. In addition, you can
provide a partial or complete log file name (as shown
in the show log output) in the log-name parameter.
3.6.1 The log-name is a required parameter.
3.5.1 This command was introduced.
Usage Guidelines In Release 3.6.1 and earlier releases, the exact directory path (/var/log) and exact filename is required to
run this command.
Starting with Release 3.7.1, this command is modified for the following:
• Display a list of all available log files (using show log).
• Display a list of log files that match the partial filename provided in the log-name parameter.
• Display the content of the specified log file if the filename matches exactly as shown in show log output.
To filter the content of a log file, you can use the show log log-name | ? command.
The following example displays the available log files.
nfvis# show log
File Name Last Modified Size
backups.log Mon Nov 13 10:30:01 2017 10758
boot.log Mon Nov 13 10:51:25 2017 13893
btmp Mon Nov 13 10:26:21 2017 768
confd_audit.log Mon Nov 13 11:05:35 2017 10423
confd_confd.log Mon Nov 13 10:49:54 2017 20977
confd_devel.log Mon Nov 13 10:49:54 2017 18969
confd.log Mon Nov 13 10:48:58 2017 582
confd_netconf.log Mon Nov 13 10:51:25 2017 1613
cron Mon Nov 13 11:01:01 2017 24762
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
134
System Log Commands
show log
The following examples display all available log files matching a partial name.
nfvis# show log nfvis
File Name Last Modified Size
nfvis_config.log Mon Nov 13 10:51:25 2017 311395
nfvis_setup.log Mon Nov 13 10:49:59 2017 3170
nfvis_syslog.log Mon Nov 13 10:51:25 2017 1483
nfvis# show log esc
File Name Last Modified Size
esc/debug_yangesc.log Mon Nov 13 10:49:53 2017 276748
esc/error_escmanager.log Mon Nov 13 10:50:06 2017 11825
esc/esc_confd.log Mon Nov 13 10:28:42 2017 588
esc/escmanager.log Mon Nov 13 10:50:19 2017 44597
esc/esc_postinit.log Mon Nov 13 10:50:25 2017 74940
esc/event_escmanager.log Mon Nov 13 10:50:19 2017 4791
esc/forever.log Mon Nov 13 10:49:07 2017 6892
esc/yangesc.log Mon Nov 13 10:49:53 2017 23982
The following examples show the content of a particular log file.
nfvis# show log nfvis_syslog.log
Nov 13 09:50:35 nfvisto6 %SYS-6-NFVIS_UP: System started by Power Switch. Up 1 minute, 42
seconds
Nov 13 09:51:35 nfvisto6 %SYS-6-UPGRADE_APPLY: Upgrade Process: In Progress
Nov 13 09:51:36 nfvisto6 %SYS-6-UPGRADE_APPLY: Upgrade Process: Restoring VMs
Example 2
The following example filters the content of a log file.
nfvis# show log esc/escmanager.log | ?
Possible completions:
append Append output text to a file
begin Begin with the line that matches
count Count the number of lines in the output
exclude Exclude lines that match
include Include lines that match
linnum Enumerate lines in the output
more Paginate output
nomore Suppress pagination
save Save output text to a file
until End with the line that matches
nfvis# show log esc/escmanager.log | include ERROR | more
02-Mar-2017 01:46:27,613 INFO [LogContextService.java:outputDecoratedLog():185] [tid=]
[cl=SM ]
[tags=threadName:VM_STATE_MACHINE-SystemAdminTena_demo7_0_8adb7f6a-ca5e-454d-9c14-fd9d5d21054f,stateMachineType:VM_STATE_MACHINE,
stateMachineContextId:
SystemAdminTena_demo7_0_8adb7f6a-ca5e-454d-9c14-fd9d5d21054f] VM_STATE_MACHINE-
SystemAdminTena_demo7_0_8adb7f6a-ca5e-454d-9c14-fd9d5d21054f Transition: VM_INERT_STATE
---- VM_ACTION_FAILED_EVENT ---- >
VM_ERROR_STATE
02-Mar-2017 01:46:27,613 INFO [ManagedObject.java:update():66] [tid=] [cl=DB ] [tags=] DB
TRANSACTION(477010616) -
UPDATE VMStateMachineDao with values
stateMachineContextId:SystemAdminTena_demo7_0_8adb7f6a-ca5e-454d-9c14-fd9d5d21054f;
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
135
System Log Commands
show log
stateMachineType:VM_STATE_MACHINE;
serviceStateMachineContextId:1a037a82-b248-4117-9156-aa26bc8e2ce1;
deploymentDetailsId:15fa65be-0775-47c3-aa46-d6eb1e428a93; previousState:VM_INERT_STATE;
currentState:
VM_ERROR_STATE; monitorSet:true; serviceDefinition:0; vmInstance:demo7; vmIndex:0;
classMetadata:SingleTableEntityPersister(com.cisco.esc.db.VMStateMachineDao);
02-Mar-2017 01:46:27,669 ERROR [StateMachineEngine.java:buildLogContext():75] [tid=] [cl=SM
] [tags=]
Unable to set log context, null values found for RequestDetails
02-Mar-2017 01:46:27,673 INFO [LogContextService.java:outputDecoratedLog():185] [tid=]
[cl=SM ]
[tags=threadName:RECOVERY_WORKFLOW_STATE_MACHINE-93cfacf5-9ee8-4e0e-9438-722944b4da2d,stateMachineType:
RECOVERY_WORKFLOW_STATE_MACHINE,stateMachineContextId:
93cfacf5-9ee8-4e0e-9438-722944b4da2d]
RECOVERY_WORKFLOW_STATE_MACHINE-93cfacf5-9ee8-4e0e-9438-722--More--
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
136
Span Session and Packet Capture Commands
• source, on page 138
• destination, on page 139
• show system monitor session, on page 140
• monitor session , on page 141
• tcpdump port, on page 142
• tcpdump vnic, on page 143
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
137
Span Session and Packet Capture Commands
source
source
To configure the source interface for a SPAN session, use the source command in session configuration mode.
To remove the source configuration, use the no form of the command.
source {all interface interface-name vlan vlan-id vm-vnic vm-name vnic-id}
no source {all interface interface-name vlan vlan-id vm-vnic vm-name vnic-id}
Syntax Description all Specifies all supported interfaces for a SPAN session.
interface interface-name Specifies a physical interface.
vlan vlan-id Specifies a VLAN interface. Range: 1 to 4094.
vm-vnic vm-name Specifies a vNIC interface with the VM name.
vnic-id Specifies the VNIC ID. Range: 0 to 8.
Command Default None
Command Modes Session configuration (config-session-2)#
Command History Release Modification
3.5.1 This command was
introduced.
Usage Guidelines In the case of virtio net or SRIOV VF, you have to specify the VM group name and NIC ID of the VM
interface. If the VM vNIC is virtio net type, then the SPAN session is applied on the OVS bridge. If VM vNIC
is SRIOV VF, then the mirror is applied to the hardware bridge. The interface name is specified for a physical
interface, for example, GE0-0 or eth0.
Example
The following configuration shows how to configure a source interface for a SPAN session:
nfvis(config)# monitor session 2
nfvis(config-session-2)# bridge lan-br
nfvis(config-session-2)# source interface GE0-0
nfvis(config-session-2)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
138
Span Session and Packet Capture Commands
destination
destination
To configure the destination interface for a SPAN session, use the destination command in session configuration
mode. To remove the destination configuration, use the no form of the command
destination {interface interface-name vlan vlan-id vm-vnic vm-name vnic-id}
no destination {interface interface-name vlan vlan-id vm-vnic vm-name vnic-id}
Syntax Description interface interface-name Specifies a physical interface.
vlan vlan-id Specifies a VLAN interface. Range: 1 to 4094.
vm-vnic vm-name Specifies a vNIC interface with the VM name.
vnic-id Specifies the VNIC ID. Range: 0 to 8.
Command Default None
Command Modes Session configuration (config-session-2)#
Command History Release Modification
3.5.1 This command was
introduced.
Usage Guidelines You must dedicate a destination port for SPAN use. Except for traffic that is required for the SPAN session,
destination ports do not receive or forward traffic. When the SPAN is configured on the system, there might
be some performance hit.
Example
The following configuration shows how to configure a destination interface for a SPAN session:
nfvis(config)# monitor session 2
nfvis(config-session-2)# bridge lan-br
nfvis(config-session-2)# destination vm-vnic 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
139
Span Session and Packet Capture Commands
show system monitor session
show system monitor session
To display the Switched Port Analyzer (SPAN) session details, use the show system monitor session command
in privileged EXEC mode.
show system monitor session
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following is a sample output of the show system monitor session command:
nfvis# show system monitor session
system monitor session 2
bridge wan-br
destination_vlan ""
destination_interface vnic0
source_vlans ""
source_rx_interfaces "GE0-0"
source_tx_interfaces "GE0-0"
source_all false
statistics "tx_bytes=142660, tx_packets=1380"
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
140
Span Session and Packet Capture Commands
monitor session
monitor session
To create a SPAN session, use the monitor session command in global configuration mode. To remove the
SPAN session, use the no form of the command.
monitor session number
no monitor session
Syntax Description number Specifies the SPAN session number. Valid range: 1-64
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example shows how to create a SPAN session:
nfvis(config)# monitor session 2
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
141
Span Session and Packet Capture Commands
tcpdump port
tcpdump port
To configure the packet capture feature on a physical port, use the tcpdump port command in global
configuration mode. Use the no form of the command to remove the packet capture.
tcpdump port port-name [{filter filter-name protocol {ARP ICMP TCP UDP} time seconds }]
no tcpdump port port-name
Syntax Description port port-name Specifies the name of the physical port.
filter filter-name (Optional) Specifies the filter name.
protocol (Optional) Specifies the protocol to capture specific packets. Supported options are:
• Internet Control Message Protocol (ICMP)
• Address Resolution Protocol (ARP)
• TCP
• UDP
time seconds (Optional) Specifies the time period over which packets are captured. The default value
is 60 seconds.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following example shows how to configure packet capture on a physical port:
nfvis(config)# tcpdump port eth0 filter filter1 time 30 pcap-location
/data/intdatastore/pktcaptures/tcpdump_eth0.pcap
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
142
Span Session and Packet Capture Commands
tcpdump vnic
tcpdump vnic
To configure the packet capture feature on a virtual network interface controller, use the tcpdump vnic
command in global configuration mode. Use the no form of the command to remove the packet capture.
tcpdump vnic tenant-name name deployment-name name vm-name name vnic-id id [{filter
filter-name protocol {ARP ICMP TCP UDP} time seconds}]
no tcpdump vnic tenant-name name deployment-name name vm-name name vnic-id id
Syntax Description tenant-name name Specifies the tenant name.
deployment-name name Specifies the deployment name.
vm-name name Specifies the name of the VM.
vnic-id id Specifies the vNIC ID.
filter filter-name (Optional) Specifies the filter name.
protocol (Optional) Specifies the protocol to capture specific packets. Supported options
are:
• Internet Control Message Protocol (ICMP)
• Address Resolution Protocol (ARP)
• TCP
• UDP
time seconds (Optional) Specifies the time period over which packets are captured. The
default value is 60.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following example shows how to configure packet capture on a vNIC:
nfvis(config)# tcpdump vnic tenant-name admin deployment-name 1489084431 vm-name ROUTER
vnic-id 0 time 30
pcap-location /data/intdatastore/pktcaptures/1489084431_ROUTER_vnic0.pcap
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
143
Span Session and Packet Capture Commands
tcpdump vnic
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
144
Upgrade Package Commands
• show system upgrade apply-image, on page 146
• show system upgrade reg-info, on page 147
• system upgrade apply-image, on page 148
• system upgrade image-name, on page 149
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
145
Upgrade Package Commands
show system upgrade apply-image
show system upgrade apply-image
Use the show system upgrade apply-image command in privileged EXEC mode to verify the upgrade status
of the Cisco Enterprise NFVIS image.
show system upgrade apply-image
Syntax Description This command has no arguments or keywords.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following is a sample output of the show system upgrade apply-image command:
nfvis# show system upgrade apply-image
NAME STATUS
------------------------------------------------------
nfvis-3.3.1 success
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
146
Upgrade Package Commands
show system upgrade reg-info
show system upgrade reg-info
Use the show system upgrade reg-info command in the privileged EXEC mode to verify the Cisco Enterprise
NFVIS image registration. Package status must be valid for the registered image.
show system upgrade reg-info [name package-name]
Syntax Description name package-name (Optional) Specifies the VM image package.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following is a sample output of the show system upgrade reg-info command:
nfvis# show system upgrade reg-info
PACKAGE
NAME LOCATION VERSION STATUS UPLOAD DATE
------------------------------------------------------------------------
nfvis-3.3.1 /data/upgrade/package 3.4.391 Valid 2016-08-10T11:57:48.711422-00:00
The table below describes the significant fields shown in the display:
Table 3: show system upgrade reg-info Field Description
Field Description
PACKAGE NAME Name of the image
LOCATION Default or non-default location of the image
VERSION Image version
STATUS Image status
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
147
Upgrade Package Commands
system upgrade apply-image
system upgrade apply-image
To upgrade to a registered Cisco Enterprise NFVIS image, use the system upgrade apply-image command
in global configuration mode. To cancel the upgrade, use the no form of this command.
system upgrade apply-image image-name scheduled-time hours [auto-restore ]
[sys-backup][vm-backup]
no system upgrade apply-image
Syntax Description image-name Specifies the image name.
scheduled-time hours Specifies the time of upgrade in hours. The valid range is from 0 to 24 hours.
auto-restore (Optional) Restores the previous image if the upgrade fails.
sys-backup (Optional) Backs up the ConfD database.
vm-backup (Optional) backs up the VM.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example shows how to upgrade to a registered Cisco Enterprise NFVIS image:
nfvis(config)# system upgrade image-name nfvis-3.3.1
nfvis(config-image-name-nfvis-3.3.1)# system upgrade apply-image scheduled-time 21
nfvis(config-image-name-nfvis-3.3.1)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
148
Upgrade Package Commands
system upgrade image-name
system upgrade image-name
To register the Cisco Enterprise NFVIS upgrade image on the host server, use the system upgrade image-name
command in global configuration mode. To remove the registration, use the no form of this command.
system upgrade image-name upgrade-name [{location}] [{default-location non-default-location}]
no system upgrade image-name upgrade-name
Syntax Description upgrade-name Name of the upgrade
location (Optional) Specifies the location of the image.
default-location (Optional) Specifies the default location (/data/upgrade/package) of the upgrade image.
non-default-location (Optional) Specifies the complete path of the folder that contains the upgrade image.
This is other than the default location.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines Ensure that you download or copy the image to the NFVIS server default target directory
"/data/upgrade/package" before starting the upgrade process. If the image is downloaded or copied to a location
other than the default directory, you will have to specify the exact path of the image when registering the
image.
Example
The following example shows how to register the Cisco Enterprise NFVIS upgrade image on the
host server:
nfvis(config)# system upgrade image-name nfvis-3.3.1
nfvis(config-image-name-nfvis-3.3.1)# system upgrade image-name nfvis1 location
/data/upgrade/package
nfvis(config-image-name-nfvis-3.3.1)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
149
Upgrade Package Commands
system upgrade image-name
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
150
Factory Default Reset Command
• factory-default-reset, on page 152
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
151
Factory Default Reset Command
factory-default-reset
factory-default-reset
To reset the Cisco Enterprise NFVIS host server to the default factory setting, use the factory-default-reset
command in global configuration mode.
factory-default-reset { all | all-except-images | all-except-images-connectivity | manufacturing |
all-with-bios-password }
Syntax Description all Erases all configuration. Connectivity is lost, and the admin password is
changed to factory default password.
all-except-images Erases all configuration except images. Connectivity is lost, and the admin
password is changed to factory default password.
all-except-images-connectivity Erases all configuration except images and network connectivity.
manufacturing Erases all configuration except images. Connectivity is lost, and the admin
password is changed to factory default password.
all-with-bios-password Erases all configuration along with the BIOS password. Connectivity is lost,
and the admin password and BIOS password is changed to factory default
password.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
4.7.1 Additional keyword introduced: all-with-bios-password
Usage Guidelines This command is used only for troubleshooting. We recommend you contact Cisco Technical Support before
using this command.
Example
The following is an example of how to reset to the default factory setting:
nfvis(config)# factory-default-reset all
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
152
Syslog Commands
• system settings logging host , on page 154
• system settings logging facility , on page 155
• system settings logging severity , on page 156
• show running-config system settings logging, on page 157
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
153
Syslog Commands
system settings logging host
system settings logging host
To configure remote host to which syslogs are sent, use the system settings logging host command in global
configuration mode.
system settings logging host ip address port transport
no system settings logging host
Syntax Description ip address Specifies the remote host address that can be IPv4/IPv6/hostname.
transport Specifies the transport protocol: UDP or TCP.
The default transport protocol is UDP, with default port 514.
For transport protocol of TCP, the default port is 601.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.6.1 This command was introduced.
Example
The following example shows how to configure remote host.
nfvis(config)# system settings logging host 172.19.162.117 port 1635 transport tcp
nfvis(config)# system settings logging host 172.19.162.111 port 163 transport udp
nfvis(config)# system settings logging host 172.19.162.112 port 1523
nfvis(config)# system settings logging host 172.19.162.114 transport tcp
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
154
Syslog Commands
system settings logging facility
system settings logging facility
To configure facility of the syslogs, use the system settings logging facility command in global configuration
mode.
system settings logging facility local
no system settings logging facility
Syntax Description local Specifies the facility number. You can configure any facility from local0 to local7.
Command Default The default facility is local7.
Command Modes Global configuration (config)
Command History Release Modification
3.6.1 This command was introduced.
Example
The following example shows how to configure facility.
nfvis(config)# nfvis(config)# system settings logging facility local
Possible completions:
local0 local1 local2 local3 local4 local5 local6 local7
nfvis(config)# nfvis(config)# system settings logging facility local3
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
155
Syslog Commands
system settings logging severity
system settings logging severity
To configure severity of the syslogs, use the system settings logging severity command in global configuration
mode.
system settings logging severity {alert | critical | debug | emergency | error | informational |
notice | warning}
no system settings logging severity
Syntax Description alert Logs at alert severity level and higher severity levels are sent.
critical Logs at critical severity level and higher severity levels are sent.
debug Logs at debug severity level and higher severity levels are sent.
emergency Logs at emergency severity level and higher severity levels are sent.
error Logs at error severity level and higher severity levels are sent.
informational Logs at informational severity level and higher severity levels are sent.
notice Logs at notice severity level and higher severity levels are sent.
warning Logs at warning severity level and higher severity levels are sent.
Command Default The default severity level is informational .
Command Modes Global configuration (config)
Command History Release Modification
3.6.1 This command was introduced.
Example
The following example shows how to configure the severity of syslogs.
nfvis(config)# system settings logging severity error
nfvis(config)# commit
nfvis(config)# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
156
Syslog Commands
show running-config system settings logging
show running-config system settings logging
To view the current syslog configuration, use the show running-config system settings logging command
in global configuration mode.
show running-config system settings logging [{host hostname | facility | severity}]
Syntax Description host Displays the current syslog host configuration
hostname Displays the current configuration for the specified host.
facility Displays the current syslog facility configuration.
severity Displays the current syslog severity configuration.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.6.1 This command was introduced.
Example
nfvis# show running-config system settings logging
system settings logging host 192.0.2.3
transport tcp
port 1635
!
system settings logging host 192.0.2.34
transport udp
port 163
!
system settings logging host 192.0.2.40
port 1523
!
nfvis# show running-config system settings logging severity
system settings logging severity error
nfvis# show running-config system settings logging facility
system settings logging facility local3
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
157
Syslog Commands
show running-config system settings logging
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
158
SNMP Commands
• snmp agent engineID , on page 160
• snmp agent sysName , on page 161
• snmp community , on page 162
• snmp enable traps , on page 163
• snmp disable traps, on page 164
• snmp group , on page 165
• snmp host , on page 166
• snmp user , on page 167
• show snmp agent , on page 168
• show snmp stats , on page 169
• show snmp traps , on page 170
• show running-config snmp, on page 171
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
159
SNMP Commands
snmp agent engineID
snmp agent engineID
To configure the engine ID used for hashing the other configuration parameters, use the snmp agent engineID
command in global configuration mode.
snmp agent engineID
Syntax Description engineID Specifies th engine ID. By default it is auto-generated.
Command Default Auto-generated
Command Modes Global configuration mode
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example configures the engine ID.
snmp agent engineID 00:22:33:22:22:22:55
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
160
SNMP Commands
snmp agent sysName
snmp agent sysName
To configure an administartively assigned system name for the managed node, use the snmp agent sysName
command in global configuration mode.
snmp agent sysName name
Syntax Description name Specifies the system
name.
Command Default Auto-generated
Command Modes Global configuration mode
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example configures the system name.
snmp agent sysName TestSystem
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
161
SNMP Commands
snmp community
snmp community
To configure SNMP community, use the snmp community command in global configuration mode.
snmp community community access
Syntax Description community (Optional) Specifies the name of the community.
access (Optional) Specifies the type of access: readOnly or writeOnly.
Command Default none
Command Modes Global configuration mode
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example configures the community pub_com with read only access.
snmp community pub_comm community-access readOnly
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
162
SNMP Commands
snmp enable traps
snmp enable traps
To enable linkup or linkdown traps for a system, use the snmp enable traps command in global configuration
mode.
snmp enable traps {linkups linkdowns}
Syntax Description linkups Specifies the linkup traps.
linkdowns Specifies the linkdown traps.
Command Default Disabled
Command Modes Global configuration mode
Command History Release Modification
3.5.1 This command was introduced.
Example
The following example enable linkup traps.
nfvis(config)# snmp enable traps linkup
commit
end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
163
SNMP Commands
snmp disable traps
snmp disable traps
To disable linkup or linkdown traps for a system, use the snmp disable traps command in global configuration
mode.
snmp disable traps {linkups linkdowns}
Syntax Description linkups Specifies the linkup traps.
linkdowns Specifies the linkdown traps.
Command Default None
Command Modes Global configuration mode
Command History Release Modification
3.5.1 This command was introduced.
Example
The following example disables linkup traps.
nfvis(config)# snmp disable traps linkup
commit
end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
164
SNMP Commands
snmp group
snmp group
To configure SNMP group, use the snmp group command in global configuration mode.
snmp group name snmp2 read write notify
Syntax Description name (Optional) Specifies the group name.
snmp2 (Optional) Specifies the SNMP type. For example, noAuthNoPriv.
read (Optional) Specifies if the group has read access.
write (Optional) Specifies if the group has write access.
notify (Optional) Specifies if the group has notify access.
Command Default none
Command Modes Global configuration mode
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example configures the SNMP group.
snmp group testgroup snmp 2 noAuthNoPriv read read-access write write-access notify
notify-access
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
165
SNMP Commands
snmp host
snmp host
To configure the SNMP host to receive traps, use the snmp host command in global configuration mode.
snmp host host-ip-address host-port host-version host-security-level host-user-name
Syntax Description host-ip-address (Optional) Specifies the IP address of the host.
host-port (Optional) Specifies the port number of the host.
host-version (Optional) Specifies the version of the host..
host-security-level (Optional) Specifies the security level.
host-user-name (Optional) Specifies the username of the host.
Command Default none
Command Modes Global configuration mode
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example configures host2 to receive traps.
snmp host host2 host-ip-address 10.2.2.2 host-port 162 host-version 2 host-security-level
noAuthNoPriv host-user-name public
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
166
SNMP Commands
snmp user
snmp user
To configure SNMP user, use the snmp user command in global configuration mode.
snmp user auth-protocol priv-protocol passphrase user-group user-version
Syntax Description auth-protocol (Optional) Specifies the user authentication protocol.
priv-protocol (Optional) Specifies the protocol privilege.
passphrase (Optional) Specifies the user password phrase.
user-group (Optional) Specifies the user group number.
user-version (Optional) Specifies user version number.
Command Default none
Command Modes Global configuration mode
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example configures the SNMP user.
snmp user public auth-protocol md5 priv-protocol des passphrase pass123 user-group 2
user-version 2
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
167
SNMP Commands
show snmp agent
show snmp agent
To get the SNMP agent information, use the show snmp agent command in privileged EXEC configuration
mode.
show snmp agent
Command Default none
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Example
admin@nfvis show snmp agent
snmp agent sysDescr "Cisco NFVIS "
snmp agent sysOID 1.3.6.1.4.1.9.12.3.1.3.2376 //platform specific
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
168
SNMP Commands
show snmp stats
show snmp stats
To get the SNMP stats information, use the show snmp stats command in privileged EXEC configuration
mode.
show snmp stats
Command Default none
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Example
admin@nfvis show snmp stats
snmp stats sysUpTime 40930629
snmp stats sysServices 70
snmp stats sysORLastChange 0
snmp stats snmpInPkts 0
snmp stats snmpInBadVersions 0
snmp stats snmpInBadCommunityNames 0
snmp stats snmpInBadCommunityUses 0
snmp stats snmpInASNParseErrs 0
snmp stats snmpSilentDrops 0
snmp stats snmpProxyDrops 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
169
SNMP Commands
show snmp traps
show snmp traps
To get the SNMP traps information, use the show snmp traps command in privileged EXEC configuration
mode. It sends SNMP trap notification to the hosts for any link status change on physical interface.
show snmp trapstrap state
Syntax Description trap (Optional) Specifies the trap: linkDown or linkUp.
state (Optional) Specifies the state of the trap: enabled or disabled.
Command Default none
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Example
admin@nfvis show snmp traps
NAME STATE
-------------------
linkDown enabled
linkUp enabled
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
170
SNMP Commands
show running-config snmp
show running-config snmp
To display the currently running SNMP configuration, use the show running-config snmp command in
privileged EXEC mode.
show running-config snmp
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show running-config snmp
snmp agent engineID 00:00:00:09:00:00:00:a6:ca:d6:38:4c
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
171
SNMP Commands
show running-config snmp
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
172
RADIUS Commands
• radius-server host, on page 174
• show running-config radius-server, on page 175
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
173
RADIUS Commands
radius-server host
radius-server host
To configure a RADIUS server host, use the radius-server host command in global configuration mode. To
delete the specified RADIUS server host, use the no form of the command.
radius-server host {ip-address | hostname} admin-priv admin-priv-number key key-number
oper-priv oper-priv-number shared-secret shared-secret-string
no radius-server host {ip-address | hostname}
Syntax Description ip-address Specifies the RADIUS server host IP address. The IP address can be an
IPv4 or IPv6 address.
hostname Specifies the RADIUS server host name. The host name can either be
an IPv4 or IPv6 address or a DNS domain name.
admin-priv admin-priv-number Specifies the minimum privilege level for administrator. Valid range is
from 1 to 15.
key key-number Specifies a preshared key for RADIUS communication between the
device and the RADIUS server.
oper-priv oper-priv-number Specifies the minimum privilege level for operator. Valid range is from
1 to 15.
shared-secret shared-secret-string Specifies the preshared secret to authenticate communication between
the device and the RADIUS server.
Command Default The default value for the admin-priv parameter is 15. The default value for the oper-priv parameter is 11.
Command Modes Switch configuration (config-switch)
Command History Release Modification
3.5.1 This command was introduced.
Example
The following example specifies a RADIUS server host.
nfvis(config-switch)# radius-server host 172.29.39.46 admin-priv 13 key 0 oper-priv 9
shared-secret myRaDIUSpassword
nfvis(config-switch)# commit
nfvis(config-switch)# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
174
RADIUS Commands
show running-config radius-server
show running-config radius-server
To display the running RADIUS server configuration information, use the show running-config radius-server
command in privileged EXEC mode.
show running-config radius-server
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show running-config radius-server
radius-server host 198.51.100.10
key 0
shared-secret sec123
admin-priv 2
oper-priv 1
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
175
RADIUS Commands
show running-config radius-server
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
176
TACACS Commands
• tacacs-server host, on page 178
• key, on page 179
• admin-priv, on page 180
• oper-priv, on page 181
• show running-config tacacs-server host, on page 182
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
177
TACACS Commands
tacacs-server host
tacacs-server host
To configure the TACACS+ server, use the tacacs-server host command in global configuration mode. To
remove the configuration, use the no form of this command.
tacacs-server host {ip-address domain-name}
notacacs-server host {ip-address domain-name}
Syntax Description ip-address Specifies the IPv4 or IPv6 address.
domain-name Specifies the DNS domain.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was introduced.
Usage Guidelines You must configure a TACACS+ server before the configured TACACS+ features on your network access
server are available.
Example
The following example shows how to configure the TACACS+ server:
nfvis(config)# tacacs-server host 192.0.2.10
nfvis(config-host-192.0.2.10)# key 0
nfvis(config-host-192.0.2.10)# admin-priv 14
nfvis(config-host-192.0.2.10)# oper-priv
nfvis(config-host-192.0.2.10)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
178
TACACS Commands
key
key
To identify the share key encryption level for all communication between the TACACS+ server and Cisco
ENCS, use the key command in host configuration mode.
key key-id
Syntax Description key-id Specifies the identification number of an authentication key. It is either zero or one. It only supports
a clear text value.
Command Default None
Command Modes Host configuration (config-host)#
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example shows how to configure the autehntication key for all communications
between the TACACS+ server and Cisco ENCS:
nfvis(config)# tacacs-server host 209.165.201.20 shared-secret test1
nfvis(config-host-209-165-201-20)# key 0
nfvis(config-host-209-165-201-20)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
179
TACACS Commands
admin-priv
admin-priv
To assign the admin privilege level to the administrator role, use the admin-priv command in host configuration
mode. To remove the privilege level configuration, use the no form of the command.
admin-priv number
no admin-priv
Syntax Description number Specifies the privilege level for the admin. Valid range: 1-15.
Command Default None
Command Modes Host configuration (config-host)#
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example shows how to configure the privilege level for the administrator role:
nfvis(config)# tacacs-server host 209.165.201.20 shared-secret test1
nfvis(config-host-209-165-201-20)# admin-priv 14
nfvis(config-host-209-165-201-20)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
180
TACACS Commands
oper-priv
oper-priv
To assign the operator privilege level to the opeartor role, use the oper-priv command in host configuration
mode. To remove the privilege level configuration, use the no form of the command.
oper-priv number
no oper-priv
Syntax Description number Specifies the privilege level for the operator role. Valid range: 1-15.
Command Default None
Command Modes Host configuration (config-host)#
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example shows how to configure the privilege level for the operator role:
nfvis(config)# tacacs-server host 209.165.201.20 shared-secret test1
nfvis(config-host-209-165-201-20)# oper-priv 9
nfvis(config-host-209-165-201-20)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
181
TACACS Commands
show running-config tacacs-server host
show running-config tacacs-server host
To display the running TACACS server configuration, use the show running-config tacacs-server command
in privileged EXEC mode.
show running-config tacacs-server host
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was introduced.
Example
nfvis# show running-config tacas-server host
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
182
User Management Commands
• rbac authentication min-pwd-length, on page 184
• rbac authentication password-lifetime, on page 185
• rbac authentication account-inactivity, on page 186
• rbac authentication users, on page 187
• rbac authentication users user activate, on page 188
• rbac authentication users user change-password , on page 189
• rbac authentication users user change-role, on page 190
• show running-config rbac authentication users, on page 191
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
183
User Management Commands
rbac authentication min-pwd-length
rbac authentication min-pwd-length
To configure the minimum length required for passwords of all users, use the rbac authentication
min-pwd-length command in global configuration mode. To set the minimum password length to default
value, use the no form of the command.
rbac authentication min-pwd-length length
Syntax Description length Specifies the minimum length. The minimum length
must be between 7 to 128 characters.
Command Default The default minimum length is 7 characters.
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 This command was introduced.
Usage Guidelines Only the admin user can use this command.
Example
nfvis(config)# configure terminal
nfvis(config)# rbac authentication min-pwd-length 14
nfvis(config)# commit
nfvis(config)# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
184
User Management Commands
rbac authentication password-lifetime
rbac authentication password-lifetime
To configure the minimum and maximum lifetime values for passwords of all users and enforce a rule to
check these values, the admin user can use the rbac authentication password-lifetime command in global
configuration mode. To set the minimum password length to default value, use the no form of the command.
rbac authentication password-lifetime enforce { true | false} min-days min-days max-days
max-days
Syntax Description enforce Enforces or removes the rule for password lifetime
validation. Valid values for this parameter are true
and false.
min-days min-days Specifies the number of days after which the users
can change the password.
max-days max-days Specifies the number of days before which the users
must change the password.
Command Default The default minimum lifetime value is set to 1 day and the default maximum lifetime value is set to 60 days.
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 This command was introduced.
Usage Guidelines • Only the admin user can use this command.
• The minimum and maximum lifetime values and the rule to check for these values are not applicable to
the admin user.
Example
nfvis(config)# configure terminal
nfvis(config)# rbac authentication password-lifetime enforce true min-days 1 max-days 30
nfvis(config)# commit
nfvis(config)# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
185
User Management Commands
rbac authentication account-inactivity
rbac authentication account-inactivity
To configure the number of days after which an unused user account is marked as inactive and to enforce a
rule to check the configured inactivity period, the admin user can use the rbac authentication
account-inactivity command in global configuration mode.
rbac authentication account-inactivity enforce { true | false} inactivity-days inactivity-days
Syntax Description enforce Enforces or removes the rule for checking and
mark-ing unused user accounts as inactive. Valid
values for this parameter are true and false.
inactivity-days inactivity-days Specifies the number of days after which an unused
account is marked as inactive.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 This command was introduced.
Usage Guidelines • Only the admin user can use this command.
• The inactivity period and the rule to check the inactivity period are not applicable to the admin user.
• When marked as inactive, a user cannot login to the system. To allow the user to again login to the system,
the ad-min user must reactivate the user account by using the rbac authentication users user username
activate command.
Example
nfvis(config)# configure terminal
nfvis(config)# rbac authentication account-inactivity enforce true inactivity-days 2
nfvis(config)# commit
nfvis(config)# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
186
User Management Commands
rbac authentication users
rbac authentication users
To create a new user, use the rbac authentication users command in global configuration mode. To delete
a user, use the no form of the command.
rbac authentication users user user-name password password role role-type
no rbac authentication users user user-name password password role role-type
Syntax Description user user-name Specifies the user name.
password Specifies the password.
password
role role-type Specifies the role of the user. The role can be one fo the following:
• Administrators—An administrator can perform all tasks.
• Operators—An operator can start, stop, and delete a VM, clear logs, and view all
information.
• Auditors—An auditor can view all information, and cannot perform any tasks.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example shows how to create a new user:
nfvis(config)# rbac authentication users user admin2 password Cisco123* role administrators
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
187
User Management Commands
rbac authentication users user activate
rbac authentication users user activate
To activate the account of an inactive user, the admin user can use the rbac authentication users user activate
command in global configuration mode.
rbac authentication users user username activate
Syntax Description username Specifies the user name.
Command Default None.
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 This command was introduced.
Usage Guidelines Only the admin user can use this command.
Example
nfvis(config)# configure terminal
nfvis(config)# rbac authentication users user guest_user activate
nfvis(config)# commit
nfvis(config)# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
188
User Management Commands
rbac authentication users user change-password
rbac authentication users user change-password
To change the existing password of a user, use the rbac authentication users user change-password command
in global configuration mode.
rbac authentication users user user-name change-password old-password password new-password
password confirm-password password
Syntax Description user user-name Specifies the user name.
old-password password Specifies the old password.
new-password password Specifies the new password.
confirm-password Confirms the new
password password.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
This command was
introduced.
Example
The following example shows how to change the password of an existing user:
nfvis(config)# rbac authentication users user admin2 change-password old-password Cisco123*
new-password Cisnfv453# confirm-password **********
nfvis(config)#commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
189
User Management Commands
rbac authentication users user change-role
rbac authentication users user change-role
To change the role of an existing user, use the rbac authentication users user change-role command in
global configuration mode.
rbac authentication users user user-name change-role old-role role-type new-role role-type
Syntax Description user user-name Specifies the user name.
old-role role-type Specifies the old role of the user.
new-role Specifies the new role of the user.
role-type
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
This command was
introduced.
Example
The following example shows how to change the user role:
nfvis(config)# rbac authentication users user admin2 change-role old-role administrators
new-role operators
nfvis(config)# commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
190
User Management Commands
show running-config rbac authentication users
show running-config rbac authentication users
To display details of all users, use the show running-config rbac authentication users command in privileged
EXEC mode.
show running-config rbac authentication users [{user user-name password role}]
Syntax Description user user-name (Optional) The specified user's details are displayed.
password (Optional) Username and password are displayed.
role user-role (Optional) Username and role are displayed.
Command Default Details of all users are displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following is a sample output of the show running-config rbac authentication users command:
nfvis# show running-config rbac authentication users
rbac authentication users user admin
role administrators
password $7$GVXJbe1IYpu4Dtfg4aAkdwxto2CtOFlW
!
rbac authentication users user test1
role administrators
password $7$Qdmzu2GHhe2zkwPl7SvxWNDNH56XV+su
!
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
191
User Management Commands
show running-config rbac authentication users
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
192
Secondary IP and Source Interface Commands
• system settings wan secondary, on page 194
• system settings source-interface , on page 195
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
193
Secondary IP and Source Interface Commands
system settings wan secondary
system settings wan secondary
To configure secondary IP on the WAN interface, use the system settings wan secondary command in global
configuration mode.
system settings wan secondary ip address
Syntax Description ip address Specifies the IP
address.
Command Default None
Command Modes Global configuration mode
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example configures the secondary WAN.
nfvis(config)# system settings wan secondary ip address 1.1.2.3 255.255.255.0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
194
Secondary IP and Source Interface Commands
system settings source-interface
system settings source-interface
To configure source interface, use the system settings source-interface command in global configuration
mode.
system settings source-interface ip address
Syntax Description ip address Specifies the IP
address.
Command Default None
Command Modes Global configuration mode
Command History Release Modification
3.5.1 This command was
introduced.
Example
The following example configures the source interface.
nfvis(config)# system settings source-interface 1.1.2.3
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
195
Secondary IP and Source Interface Commands
system settings source-interface
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
196
Ports and Port Channel Commands
• hostaction pnic-breakout, on page 198
• hostaction pnic-breakout force, on page 199
• pnic, on page 200
• show nic, on page 202
• show pnic, on page 203
• show pnic-breakout, on page 205
• show port-channel, on page 206
• show lldp stats, on page 207
• show lldp neighbors, on page 208
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
197
Ports and Port Channel Commands
hostaction pnic-breakout
hostaction pnic-breakout
To change the PNIC mode from 2x40G to 4x10G or from 4x10G to 2x40G, use the hostaction pnic-breakout
device command in privileged EXEC mode.
hostaction pnic-breakout device number mode pnic mode
Syntax Description pnic-breakout Changes the PNIC mode from 2x40G to 4x10G or vice-versa.
device number Specifies the number of devices on which the mode must be changed.
mode pnic Specifies the desired PNIC mode (4x10 or 2x40).
mode
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
4.7.1 This command was
introduced.
Example
nfvis# hostaction pnic-breakout device 1 mode 4x10
Warning: Will reboot the system after the mode is changed on the 40G PNIC. All PNIC
configuration like adminstatus, duplex, lldp, promiscuous, speed, sriov, track-state
will be lost and set to default.
Are you sure you want to perform the PNIC breakout? [no,yes] yes
System message at 2021-06-02 21:15:36...
Commit performed ny via tcp using system.
Broadcast message from root@nfvis (Wed 2021-06-02 21:15:36 UTC):
The system is going down for reboot at Wed 2021-06-02 21:16:36 UTC!
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
198
Ports and Port Channel Commands
hostaction pnic-breakout force
hostaction pnic-breakout force
To forcefully breakout from 2x40G mode to 4x10G mode or vice-versa, use the hostaction pnic-breakout
force command in privileged EXEC mode. This command is used exclusively for return merchandise
authorization (RMA) cases.
hostaction pnic-breakout force device number mode pnic mode
Syntax Description pnic-breakout Changes the PNIC mode from 2x40G to 4x10G or vice-versa.
force Forces the PNIC mode change.
device number Specifies the number of devices on which the mode must be changed.
mode pnic Specifies the desired PNIC mode (2x40 or 4x10).
mode
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
4.7.1 This command was
introduced.
Example
nfvis# hostaction pnic-breakout force device 1 mode 4x10
Warning: Will reboot the system after the mode is changed on the 40G PNIC. All PNIC
configuration like adminstatus, duplex, lldp, promiscuous, speed, sriov, track-state
will be lost and set to default.
Are you sure you want to perform the PNIC breakout? [no,yes] yes
Broadcast message from root@nfvis (Wed 2021-06-02 21:38:53 UTC):
The system is going down for reboot at Wed 2021-06-02 21:39:53 UTC!
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
199
Ports and Port Channel Commands
pnic
pnic
To modify the configuration of an Ethernet port or to create a port channel, use the pnic command. To set an
Ethernet port to its default settings or to delete a port channel, use the no form of the command.
pnic name [adminstatus {up | down}] [type {ethernet | port_channel}] [bond_mode
{active-backup | balance-slb | balance-tcp}] [lacp_type {active | passive | off}] [member_of
portchannel_name] [trunks vlan_num] [lldp {enabled | disabled}]
no pnic name [adminstatus] [type] [bond_mode] [lacp_type] [lldp] [member_of
portchannel_name]
Syntax Description name Specifies the name of the port.
adminstatus Brings a port up or down administratively. Valid values are up and down.
Note adminstatus is not supported on port channel.
type Specifies the type of the port. Valid values are ethernet and port_channel. To
create a port channel, you must specify the value as port_channel.
bond_mode Specifies the bond mode for a port channel. Valid values are active-backup,
balance-slb, and balance-tcp. Default is balance-tcp.
lacp_type Specifies the LACP type for a port channel. Valid values are off, active, and
passive. Default is off.
member_of Adds the port to the specified port channel.
portchannel_name
trunks vlan_num Specifies the VLANs. Valid range is from 1 to 4096. Default is VLAN 1. Enter
VLANs separated by commas, VLAN ranges separated by dashes, or a
combination of both.
lldp Enables or disables LLDP on a port. Valid values are enable and disable. Default
is disable.
Note lldp is not supported on port channel.
Command Default None
Command Modes Global configuration (config)
Command History Release Modification
3.7.1 This command was introduced.
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
200
Ports and Port Channel Commands
pnic
Example
nfvis# config
nfvis(config)# pnic pc type port_channel
nfvis(config-pnic-pc)# commit
nfvis(config-pnic-pc)# end
Example
nfvis# config
nfvis(config)# no pnic eth2 member_of pc
nfvis(config-pnic-eth2)# commit
nfvis(config-pnic-eth2)# end
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
201
Ports and Port Channel Commands
show nic
show nic
To display the various NIC cards inserted in the CSP device, use the show nic command in privileged EXEC
mode.
show nic
Syntax Description This command has no keywords or arguments.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
4.7.1 This command was
introduced.
Example
nfvis# show nic
SLOTID ADAPTER VENDOR DEVID MODE DEVNO PNICS
-------------------------------------------------------------------------------------------------------------------
1 Intel X520 dual port adapter 8086 10fb NA NA ['eth1-1', 'eth1-2']
3 Intel X710-DA4 Quad Port 10Gb SFP+ 8086 1572 NA NA ['eth3-1', 'eth3-2',
'eth3-3', 'eth3-4']
converged NIC
2 Intel XL710-QDA2 Dual Port 40Gb 8086 1583 2x40 1 ['eth2-1', 'eth2-2']
QSFP converged NIC
5 Intel i350 Quad Port 1Gb Adapter 8086 1521 NA NA ['eth5-1', 'eth5-2',
'eth5-3', 'eth5-4']
4 Intel X520 dual port adapter 8086 10fb NA NA ['eth4-1', 'eth4-2']
6 Intel X520 dual port adapter 8086 10fb NA NA ['eth6-1', 'eth6-2']
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
202
Ports and Port Channel Commands
show pnic
show pnic
To display all statistics or only specific information about a port or all ports, use the show pnic command in
privileged EXEC mode.
show pnic [name] [{adminstatus | link_state | mac_address | mtu | operational-speed |
passthrough | pch_state | refcnt | speed | sriov_intf | stats}]
Syntax Description name Specifies the name of the port for which the information is displayed.
adminstatus Displays the up or down status.
link_state Displays the link state.
mac_address Displays the MAC address.
mtu Displays the maximum transmission unit (MTU) size.
operational-speed Displays the operational speed.
passthrough Displays the passthrough mode.
pch_state Displays the port channel state.
refcnt Displays the reference count.
speed Displays the interface speed.
sriov_intf Displays the SRIOV interface.
stats Displays the statistics.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# show pnic
Name Link Admin MTU Mac Passthrough Speed Op-speed Rx
Bytes Packets Errors Dropped Mbps Broadcast Multicast TX Bytes Packets
Errors Dropped Collisions Mbps Broadcast Multicast
================================================================================================================================================================================
eth0 up up 9000 d8:b1:90:ff:f5:88 none 1G 1000
1469476983 17749881 0 0 14156964 2888574 198310581
272571 0 0 40
68440
eth1 up up 9000 d8:b1:90:ff:f5:89 none 1G 1000
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
203
Ports and Port Channel Commands
show pnic
19826137 329353 0 0 0 325498 4180179 27586
0 0
0 27586
eth2 down up 9000 d8:b1:90:ff:d8:3c none 1G 0 0
0 0 0 0 0 0 0
0 0
0 0
eth3 down up 9000 d8:b1:90:ff:d8:3d none 1G 0 0
0 0 0 0 0 0 0
0 0
0 0
eth4 down up 9000 d8:b1:90:ff:d8:3e none 1G 0 0
0 0 0 0 0 0 0
0 0
0 0
eth5 down up 9000 d8:b1:90:ff:d8:3f none 1G 0 0
0 0 0 0 0 0 0
0 0
0 0
Example
nfvis# show pnic stats
Name Rx Bytes Packets Errors Dropped Mbps Broadcast Multicast TX Bytes
Packets Errors Dropped Collisions Mbps Broadcast Multicast
=========================================================================================================================================================================
eth0 1469743586 17753343 0 0 14159834 2889066 198318715
272603 0 0 40 68450
eth1 19830637 329428 0 0 0 325573 4181034
27591 0 0 0 27591
eth2 0 0 0 0 0 0 0
0 0 0 0 0
eth3 0 0 0 0 0 0 0
0 0 0 0 0
eth4 0 0 0 0 0 0 0
0 0 0 0 0
eth5 0 0 0 0 0 0 0
0 0 0 0 0
0
Example
nfvis# show pnic eth1 stats
stats receive bytes 19862257
stats receive packets 329955
stats receive errors 0
stats receive dropped 0
stats receive broadcast 0
stats receive multicast 326100
stats transmit bytes 4187361
stats transmit packets 27628
stats transmit errors 0
stats transmit dropped 0
stats transmit broadcast 0
stats transmit multicast 27628
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
204
Ports and Port Channel Commands
show pnic-breakout
show pnic-breakout
To display the 40G NIC mode and adapter information, use the show pnic-breakout command in privileged
EXEC mode.
show pnic-breakout
Syntax Description This command has no keywords or arguments.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
4.7.1 This command was
introduced.
Example
nfvis# show pnic-breakout
DEVNO PCI VENDOR DEVID ADAPTER MODE PNICS
-----------------------------------------------------------------------------------------------------
1 5e 8086 1583 Cisco(R) Ethernet Converged NIC XL710-QDA2 2x40 ['eth2-1',
'eth2-2']
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
205
Ports and Port Channel Commands
show port-channel
show port-channel
To show configured port channels, use the show port-channel command in privileged EXEC mode.
show port-channel
Syntax Description This command has no keywords or parameters.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# show port-channel
---- bondtrue ----
bond_mode: active-backup
bond may use recirculation: no, Recirc-ID : -1
bond-hash-basis: 0
updelay: 0 ms
downdelay: 0 ms
lacp_status: off
active slave mac: 00:00:00:00:00:00(none)
slave eth1: disabled
may_enable: false
slave eth2: disabled
may_enable: false
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
206
Ports and Port Channel Commands
show lldp stats
show lldp stats
To display LLDP statistics, use the show lldp stats command in privileged EXEC mode.
show lldp stats
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# show lldp stats
TX DISCARD ERROR RX DISCARDED UNREC
NAME FRAMES RX RX FRAMES TLVS TLVS AGEOUTS
-----------------------------------------------------------------
eth0 23 0 0 19667 0 0 0
eth1 0 0 0 0 0 0 0
eth2 0 0 0 0 0 0 0
eth3 0 0 0 0 0 0 0
eth4 0 0 0 0 0 0 0
eth5 0 0 0 0 0 0 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
207
Ports and Port Channel Commands
show lldp neighbors
show lldp neighbors
To display information about LLDP neighbors, use the show lldp neighbors command in privileged EXEC
mode.
show lldp neighbors
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# show lldp neighbors
NAME DEVICE ID HOLDTIME CAPS PLATFORM PORTID DESCRIPTION
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
eth0 Switch1623 120 Bridge, Router Cisco IOS Software, Catalyst L3 Switch Software
(CAT3K_CAA-UNIVERSALK9-M),
Version 15.0(1)EX3, RELEASE SOFTWARE (fc2) Ifname: Gi1/0/4
GigabitEthernet1/0/4
eth1 None 0 None None None None
eth2 None 0 None None None None
eth3 None 0 None None None None
eth4 None 0 None None None None
eth5 None 0 None None None None
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
208
Secure Overlay and BGP Commands
• show secure-overlay, on page 210
• show bgp vpnv4 unicast, on page 211
• show bgp vpnv4 unicast route, on page 212
• show bgp vpnv4 unicast summary, on page 213
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
209
Secure Overlay and BGP Commands
show secure-overlay
show secure-overlay
To display the secure overlay status, use the show secure-overlay command in privileged EXEC mode.
show secure-overlay
Command Default Information about secure overlay state is displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.10.1 This command was introduced.
Example
The following is a sample output of the show secure-overlay command:
nfvis# show secure-overlay
secure-overlay test
state up
active-local-bridge wan-br
selected-local-bridge wan-br
active-local-system-ip-addr 90.90.90.8
active-remote-interface-ip-addr 10.30.1.113
active-remote-system-ip-addr 90.90.90.1
active-remote-system-ip-subnet 90.90.90.1/32
active-remote-id "\"10.30.1.113\""
nfvis# show bgp ?
Possible completions:
ipv4 Address family
vpnv4 Address family
| Output modifiers
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
210
Secure Overlay and BGP Commands
show bgp vpnv4 unicast
show bgp vpnv4 unicast
To display the local BGP status for BGP over IPSec tunnel, use the show bgp vpnv4 unicast command in
privileged EXEC mode.
show bgp vpn4 unicast
Command Default Information about local BGP status for BGP over IPSec tunnel is displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
4.5.1 This command was introduced.
Example
The following is a sample output of the show bgp vpnv4 unicast command:
nfvis# show bgp vpnv4 unicast
Family Transmission Router ID Local AS Number
vpnv4 unicast 169.254.1.1 200
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
211
Secure Overlay and BGP Commands
show bgp vpnv4 unicast route
show bgp vpnv4 unicast route
To display the BGP learned/announced routes for BGP over IPSec tunnel, use the show bgp vpnv4 unicast
route command in privileged EXEC mode.
show bgp vpn4 unicast route
Command Default Information about the BGP learned/announced routes for BGP over IPSec tunnel is displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
4.5.1 This command was introduced.
Example
The following is a sample output of the show bgp vpnv4 unicast route command:
nfvis# show bgp vpnv4 unicast route
Network Next-Hop Metric LocPrf Path
91.91.91.0/24 90.90.90.1 0 100 65000 ?
92.92.92.0/24 90.90.90.1 0 100 65000 ?
10.20.0.0/24 0.0.0.0 i
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
212
Secure Overlay and BGP Commands
show bgp vpnv4 unicast summary
show bgp vpnv4 unicast summary
To display the BGP neighbor status for BGP over IPSec tunnel, use the show bgp vpnv4 unicast summary
command in privileged EXEC mode.
show bgp vpn4 unicast summary
Command Default Information about the BGP neighbor status for BGP over IPSec tunnel is displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
4.5.1 This command was introduced.
Example
The following is a sample output of the show bgp vpnv4 unicast summary command:
nfvis# show bgp vpnv4 unicast summary
Neighbor IP Version AS Number Up/Down
90.90.90.1 4 65000 up
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
213
Secure Overlay and BGP Commands
show bgp vpnv4 unicast summary
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
214
Storage Virtualization Commands
• cluster datastore intdatastore, on page 216
• cluster migrate-deployment, on page 217
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
215
Storage Virtualization Commands
cluster datastore intdatastore
cluster datastore intdatastore
To create a cluster, to do a cold migration of VMs, use the cluster datastore intdatastore command in
privileged EXEC mode. To delete a cluster, use the no form of the command.
cluster cluster name { datastore [ intdatastore | extdatastore1 | extdatastore2 ] | size size number
| node ipv4 address addresstype ipv4 | node ipv4 address addresstype ipv4 | node ipv4 address addresstype
ipv4 }
no cluster cluster name
Syntax Description cluster cluster name Specifies the name of the cluster.
datastore Specifies the datastore to be selected for creating a cluster.
intdatastore|extdatastore1|extdatastore2
size size number Specifies the size of the datastore.
node Specifies the address and address type of the device in the
cluster.
Note Three nodes must be added to the configuration, for the commit to be successful.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
4.8.1 This command was
introduced.
Example
nfvis(config)# cluster cluster1 datastore intdatastore size 10
nfvis(config-cluster-test)#node 209.165.200.225 address-type ipv4
nfvis(config-node-209.165.200.254)#exit
nfvis(config-cluster-test)#node 209.165.201.31 address-type ipv4
nfvis(config-node-209.165.200.224)#exit
nfvis(config-cluster-test)#node 209.165.201.1 address-type ipv4
nfvis(config-node-209.165.202.129)#commit
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
216
Storage Virtualization Commands
cluster migrate-deployment
cluster migrate-deployment
To migrate deployments from a source node to a destination node, use the cluster migrate-deployment
command in privileged EXEC mode.
cluster cluster name { migrate-deployment | source-node ip address | destination node ip
address [ | all-deployments | deployment-list ] }
Syntax Description cluster cluster name Specifies the cluster in which the deployments must be migrated.
source-node ip address Specifies the node from which the deployment must be migrated.
destination node ip address Specifies the node to which the deployment must be migrated.
all-deployments Specifies that all deployments in the cluster need to be migrated.
deployment-list Specifies the deployments to by migrated.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
4.8.1 This command was
introduced.
Example
nfvis# cluster test migrate-deployment source-node 209.165.200.225 destination-node
209.165.201.31 all-deployments
nfvis# cluster test migrate-deployment source-node 209.165.200.225 destination-node
209.165.201.31 deployment-list [ centosvm4 centosvm5 ]
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
217
Storage Virtualization Commands
cluster migrate-deployment
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
218
Support Commands
• support show arp, on page 221
• support show bgp, on page 222
• support show bgp route, on page 223
• support show config-drive, on page 224
• support show config-drive content, on page 225
• support show cpuinfo, on page 226
• support show date-time, on page 227
• support show df, on page 228
• support show domainname, on page 229
• support show dmidecode, on page 230
• support show ethtool, on page 232
• support show ifconfig, on page 236
• support show iostat, on page 237
• support show ipsec, on page 238
• support show loadavg, on page 239
• support show meminfo, on page 240
• support show netstattcp, on page 242
• support show netstatudp, on page 243
• support show procstat, on page 244
• support show route, on page 246
• support show snmp, on page 247
• support show system-version, on page 248
• support show system-hostname, on page 249
• support virsh all-info, on page 250
• support virsh capabilities, on page 253
• support virsh cpu-stats, on page 257
• support virsh domiflist, on page 258
• support virsh dumpxml, on page 259
• support virsh iface-list, on page 261
• support virsh iface-dumpxml, on page 262
• support virsh list, on page 263
• support virsh memory-stats, on page 264
• support virsh net-dumpxml, on page 265
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
219
Support Commands
• support virsh net-list, on page 266
• support virsh net-info, on page 267
• support virsh nodecpustats, on page 268
• support virsh pool-list, on page 269
• support virsh pool-dumpxml, on page 270
• support virsh sys-info, on page 271
• support virsh vol-dumpxml, on page 274
• support virsh vol-list, on page 275
• support ovs all-info, on page 276
• support ovs appctl fdb-show, on page 278
• support ovs dpctl show, on page 280
• support ovs ofctl dump-ports, on page 281
• support ovs ofctl dump-ports-desc, on page 282
• support ovs vsctl list-br, on page 283
• support ovs vsctl list interface, on page 284
• support ovs vsctl list-ports, on page 285
• support ovs vsctl show, on page 286
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
220
Support Commands
support show arp
support show arp
To display the ARP table, use the support show arp command in privileged EXEC mode.
support show arp
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show arp
IP address HW type Flags HW address Mask Device
203.0.113.1 0x1 0x2 00:25:b4:47:44:00 * wan-br
203.0.113.1 0x1 0x2 3c:ce:73:da:60:00 * wan-br
203.0.113.1 0x1 0x2 00:00:0c:9f:f0:15 * wan-br
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
221
Support Commands
support show bgp
support show bgp
To display the BGP session details, use the support show bgp command in privileged EXEC mode.
support show bgp
Command Default Information about BGP session details is displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
4.5.1 This command was introduced.
Example
The following is a sample output of the support show bgp command:
nfvis# support show bgp
BIRD 1.6.8 ready.
name proto table state since info
bgp_bgp_neighbor BGP bgp_table_bgp_neighbor up 22:35:37 Established
Preference: 100
Input filter: ACCEPT
Output filter: ACCEPT
Import limit: 15
Action: disable
Routes: 2 imported, 1 exported, 4 preferred
Route change stats: received rejected filtered ignored accepted
Import updates: 2 0 0 0 2
Import withdraws: 0 0 --- 0 0
Export updates: 3 2 0 --- 1
Export withdraws: 0 --- --- --- 0
BGP state: Established
Neighbor address: 90.90.90.1
Neighbor AS: 65000
Neighbor ID: 90.90.90.1
Neighbor caps: refresh enhanced-refresh AS4
Session: external multihop AS4
Source address: 90.90.90.8
Route limit: 2/15
Hold timer: 173/240
Keepalive timer: 39/80
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
222
Support Commands
support show bgp route
support show bgp route
To display the BGP routes learnt through BGP, use the support show bgp route command in privileged
EXEC mode.
support show bgp route
Command Default Information about the BGP routes learnt through BGP is displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
4.5.1 This command was introduced.
Example
The following is a sample output of the support show bgp route command:
nfvis# support show bgp route
BIRD 1.6.8 ready.
91.91.91.0/24 dev ipsec0 [bgp_bgp_neighbor 22:35:37 from 90.90.90.1] (100) [AS65000?]
Type: BGP unicast univ
BGP.origin: Incomplete
BGP.as_path: 65000
BGP.next_hop: 90.90.90.1
BGP.med: 0
BGP.local_pref: 100
92.92.92.0/24 dev ipsec0 [bgp_bgp_neighbor 22:35:37 from 90.90.90.1] (100) [AS65000?]
Type: BGP unicast univ
BGP.origin: Incomplete
BGP.as_path: 65000
BGP.next_hop: 90.90.90.1
BGP.med: 0
BGP.local_pref: 100
nfvis#
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
223
Support Commands
support show config-drive
support show config-drive
To display the VM Day-0 configuration file listing, use the support show config-drive command in privileged
EXEC mode.
support show config-drive domain
Syntax Description domain Specifies the domain ID or name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show config-drive 12
-rw-r--r--. 1 qemu qemu 393216 Dec 1 00:25
/cisco/esc/esc_database/nodejs/VM/4e802bd4-c6e4-4c7b-a163-787927324967/
4e802bd4-c6e4-4c7b-a163-787927324967-hdd.config
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
224
Support Commands
support show config-drive content
support show config-drive content
To display the brief content of VM Day-0 configuration file, use the support show config-drive content
command in privileged EXEC mode.
support show config-drive content domain
Syntax Description domain Specifies the domain ID or name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show config-drive content 12
<version text="1"/> <hypervisor text="nfvis"/> <guest text="TEST"/> <gateway addr="10.1.1.1"/>
<mgmt-intf text="Virtual2"/>
<data-intf text="SHARED"/> <localip addr="10.1.1.1" mask="10.1.1.1"/> <int-intf
text="Virtual1"/>
<intip addr="10.20.0.3" mask="255.255.255.0"/> <cm addr="10.1.1.1"/> <ntp addr="10.1.1.1"/>
</bootstrap>
vWAAS-6000R <bootstrap> <version text="1"/> <hypervisor text="nfvis"/> <guest text="TEST"/>
<gateway addr="10.1.1.1"/>
<mgmt-intf text="Virtual2"/> <data-intf text="SHARED"/> <localip addr="10.1.1.1"
mask="10.1.1.1"/>
<int-intf text="Virtual1"/> <intip addr="10.20.0.3" mask="255.255.255.0"/>
<cm addr="10.1.1.1"/> <ntp addr="10.1.1.1"/> </bootstrap>
vWAAS-6000R
{"files":[{"path":"bootstrap-cfg.xml","content_path":"/content/0000"},{"path":"model.txt","content_path":
"/content/0001"}]}
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
225
Support Commands
support show cpuinfo
support show cpuinfo
To display CPU information, use the support show cpuinfo command in privileged EXEC mode.
support show cpuinfo
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 79
model name : Intel(R) Xeon(R) CPU E5-2630 v4 @ 2.20GHz
stepping : 1
microcode : 0xb00001f
cpu MHz : 1265.859
cache size : 25600 KB
physical id : 0
siblings : 20
core id : 0
cpu cores : 10
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 20
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts
acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon
pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf eagerfpu pni pclmulqdq dtes64
monitor ds_cpl vmx smx est tm2 ssse3 fma cx16 xtpr pdcm pcid dca sse4_1 sse4_2 x2apic movbe
popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm abm 3dnowprefetch ida arat epb
pln pts dtherm intel_pt tpr_shadow vnmi flexpriority ept vpid fsgsbase tsc_adjust bmi1 hle
avx2 smep bmi2 erms invpcid rtm cqm rdseed adx smap xsaveopt cqm_llc cqm_occup_llc
cqm_mbm_total cqm_mbm_local
bogomips : 4389.33
clflush size : 64
cache_alignment : 64
address sizes : 46 bits physical, 48 bits virtual
power management:
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
226
Support Commands
support show date-time
support show date-time
To display the date and time information, use the support show date-time command in privileged EXEC
mode.
support show date-time
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show date-time
Thu Nov 16 10:50:52 UTC 2017
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
227
Support Commands
support show df
support show df
To display the amount of disk space used and available, use the support show df command in privileged
EXEC mode.
support show df
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show df
Filesystem Type 1024-blocks Used Available Capacity Mounted on
/dev/mapper/vg_nfv-lv_root ext4 8125880 1755256 5934812 23% /
devtmpfs devtmpfs 65863696 0 65863696 0% /dev
tmpfs tmpfs 65874332 12 65874320 1% /dev/shm
tmpfs tmpfs 65874332 1224 65873108 1% /run
tmpfs tmpfs 65874332 0 65874332 0% /sys/fs/cgroup
/dev/sda2 ext4 739536 112860 572916 17% /boot
/dev/mapper/vg_nfv-lv_var ext4 3997376 137112 3634168 4% /var
/dev/mapper/vg_nfv-lv_data ext4 2311085988 4765488 2305792116 1% /data
tmpfs tmpfs 13174868 0 13174868 0% /run/user/0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
228
Support Commands
support show domainname
support show domainname
To display the information about domain name, use the support show domainname command in privileged
EXEC mode.
support show domainname
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show domainname
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
229
Support Commands
support show dmidecode
support show dmidecode
To display the system hardware information, use the support show dmidecode command in privileged EXEC
mode.
support show dmidecode
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show dmidecode
# dmidecode 3.0
Scanning /dev/mem for entry point.
SMBIOS 3.0.0 present.
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: Cisco Systems Inc
Product Name: UCSC-C220-M4S
Version: A0
Serial Number: FCH2110V0DX
UUID: EB7C9CE9-9DF9-3142-898B-C84A16B10706
Wake-up Type: Power Switch
SKU Number: Not Specified
Family: Not Specified
Handle 0x0002, DMI type 2, 15 bytes
Base Board Information
Manufacturer: Cisco Systems Inc
Product Name: UCSC-C220-M4S
Version: 74-12419-02
Serial Number: FCH2108JLC4
Asset Tag: Unknown
Features:
Board is a hosting board
Board is replaceable
Location In Chassis: Not Specified
Chassis Handle: 0x0003
Type: Server Blade
Contained Object Handles: 0
Handle 0x0003, DMI type 3, 25 bytes
Chassis Information
Manufacturer: Cisco Systems Inc
Type: Rack Mount Chassis
Lock: Not Present
Version: 74-12502-02
Serial Number: FCH2110V0DX
Asset Tag: Unknown
Boot-up State: Safe
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
230
Support Commands
support show dmidecode
Power Supply State: Safe
Thermal State: Safe
Security Status: None
OEM Information: 0x00018755
Height: 1 U
Number Of Power Cords: 1
Contained Elements: 1
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
231
Support Commands
support show ethtool
support show ethtool
To display the standard information about a device, use the support show ethtool command in privileged
EXEC mode.
support show ethtool devicename
Syntax Description devicename Specifies the name of the device.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show ethtool eth1
nfvis# support show ethtool eth1
Driver information for device eth1
driver: igb
version: 5.3.0-k
firmware-version: 1.63, 0x80000b15, 0.384.130
expansion-rom-version:
bus-info: 0000:01:00.1
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: no
Features for eth1:
rx-checksumming: on
tx-checksumming: on
tx-checksum-ipv4: off [fixed]
tx-checksum-ip-generic: on
tx-checksum-ipv6: off [fixed]
tx-checksum-fcoe-crc: off [fixed]
tx-checksum-sctp: on
scatter-gather: on
tx-scatter-gather: on
tx-scatter-gather-fraglist: off [fixed]
tcp-segmentation-offload: on
tx-tcp-segmentation: on
tx-tcp-ecn-segmentation: off [fixed]
tx-tcp6-segmentation: on
udp-fragmentation-offload: off [fixed]
generic-segmentation-offload: on
generic-receive-offload: on
large-receive-offload: off [fixed]
rx-vlan-offload: on
tx-vlan-offload: on
ntuple-filters: off
receive-hashing: on
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
232
Support Commands
support show ethtool
highdma: on [fixed]
rx-vlan-filter: on [fixed]
vlan-challenged: off [fixed]
tx-lockless: off [fixed]
netns-local: off [fixed]
tx-gso-robust: off [fixed]
tx-fcoe-segmentation: off [fixed]
tx-gre-segmentation: off [fixed]
tx-ipip-segmentation: off [fixed]
tx-sit-segmentation: off [fixed]
tx-udp_tnl-segmentation: off [fixed]
tx-mpls-segmentation: off [fixed]
fcoe-mtu: off [fixed]
tx-nocache-copy: off
loopback: off [fixed]
rx-fcs: off [fixed]
rx-all: off
tx-vlan-stag-hw-insert: off [fixed]
rx-vlan-stag-hw-parse: off [fixed]
rx-vlan-stag-filter: off [fixed]
busy-poll: off [fixed]
tx-sctp-segmentation: off [fixed]
l2-fwd-offload: off [fixed]
hw-tc-offload: off [fixed]
Permanent address: 70:db:98:70:2f:6f
Pause parameters for eth1:
Autonegotiate: on
RX: off
TX: off
NIC statistics:
rx_packets: 0
tx_packets: 0
rx_bytes: 0
tx_bytes: 0
rx_broadcast: 0
tx_broadcast: 0
rx_multicast: 0
tx_multicast: 0
multicast: 0
collisions: 0
rx_crc_errors: 0
rx_no_buffer_count: 0
rx_missed_errors: 0
tx_aborted_errors: 0
tx_carrier_errors: 0
tx_window_errors: 0
tx_abort_late_coll: 0
tx_deferred_ok: 0
tx_single_coll_ok: 0
tx_multi_coll_ok: 0
tx_timeout_count: 0
rx_long_length_errors: 0
rx_short_length_errors: 0
rx_align_errors: 0
tx_tcp_seg_good: 0
tx_tcp_seg_failed: 0
rx_flow_control_xon: 0
rx_flow_control_xoff: 0
tx_flow_control_xon: 0
tx_flow_control_xoff: 0
rx_long_byte_count: 0
tx_dma_out_of_sync: 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
233
Support Commands
support show ethtool
tx_smbus: 0
rx_smbus: 0
dropped_smbus: 0
os2bmc_rx_by_bmc: 0
os2bmc_tx_by_bmc: 0
os2bmc_tx_by_host: 0
os2bmc_rx_by_host: 0
tx_hwtstamp_timeouts: 0
rx_hwtstamp_cleared: 0
rx_errors: 0
tx_errors: 0
tx_dropped: 0
rx_length_errors: 0
rx_over_errors: 0
rx_frame_errors: 0
rx_fifo_errors: 0
tx_fifo_errors: 0
tx_heartbeat_errors: 0
tx_queue_0_packets: 0
tx_queue_0_bytes: 0
tx_queue_0_restart: 0
tx_queue_1_packets: 0
tx_queue_1_bytes: 0
tx_queue_1_restart: 0
tx_queue_2_packets: 0
tx_queue_2_bytes: 0
tx_queue_2_restart: 0
tx_queue_3_packets: 0
tx_queue_3_bytes: 0
tx_queue_3_restart: 0
tx_queue_4_packets: 0
tx_queue_4_bytes: 0
tx_queue_4_restart: 0
tx_queue_5_packets: 0
tx_queue_5_bytes: 0
tx_queue_5_restart: 0
tx_queue_6_packets: 0
tx_queue_6_bytes: 0
tx_queue_6_restart: 0
tx_queue_7_packets: 0
tx_queue_7_bytes: 0
tx_queue_7_restart: 0
rx_queue_0_packets: 0
rx_queue_0_bytes: 0
rx_queue_0_drops: 0
rx_queue_0_csum_err: 0
rx_queue_0_alloc_failed: 0
rx_queue_1_packets: 0
rx_queue_1_bytes: 0
rx_queue_1_drops: 0
rx_queue_1_csum_err: 0
rx_queue_1_alloc_failed: 0
rx_queue_2_packets: 0
rx_queue_2_bytes: 0
rx_queue_2_drops: 0
rx_queue_2_csum_err: 0
rx_queue_2_alloc_failed: 0
rx_queue_3_packets: 0
rx_queue_3_bytes: 0
rx_queue_3_drops: 0
rx_queue_3_csum_err: 0
rx_queue_3_alloc_failed: 0
rx_queue_4_packets: 0
rx_queue_4_bytes: 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
234
Support Commands
support show ethtool
rx_queue_4_drops: 0
rx_queue_4_csum_err: 0
rx_queue_4_alloc_failed: 0
rx_queue_5_packets: 0
rx_queue_5_bytes: 0
rx_queue_5_drops: 0
rx_queue_5_csum_err: 0
rx_queue_5_alloc_failed: 0
rx_queue_6_packets: 0
rx_queue_6_bytes: 0
rx_queue_6_drops: 0
rx_queue_6_csum_err: 0
rx_queue_6_alloc_failed: 0
rx_queue_7_packets: 0
rx_queue_7_bytes: 0
rx_queue_7_drops: 0
rx_queue_7_csum_err: 0
rx_queue_7_alloc_failed: 0
Coalesce parameters for eth1:
Adaptive RX: off TX: off
stats-block-usecs: 0
sample-interval: 0
pkt-rate-low: 0
pkt-rate-high: 0
rx-usecs: 3
rx-frames: 0
rx-usecs-irq: 0
rx-frames-irq: 0
tx-usecs: 0
tx-frames: 0
tx-usecs-irq: 0
tx-frames-irq: 0
rx-usecs-low: 0
rx-frame-low: 0
tx-usecs-low: 0
tx-frame-low: 0
rx-usecs-high: 0
rx-frame-high: 0
tx-usecs-high: 0
tx-frame-high: 0
Ring parameters for eth1:
Pre-set maximums:
RX: 4096
RX Mini: 0
RX Jumbo: 0
TX: 4096
Current hardware settings:
RX: 256
RX Mini: 0
RX Jumbo: 0
TX: 256
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
235
Support Commands
support show ifconfig
support show ifconfig
To display the configuration details of all network interfaces or a specific interface, use the support show
ifconfig command in privileged EXEC mode.
support show ifconfig interface
Syntax Description interface Specifies the interface name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show ifconfig wan-br
wan-br: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 9000
inet 172.19.181.196 netmask 255.255.255.0 broadcast 172.19.181.255
inet6 fe80::72db:98ff:fe70:2f6e prefixlen 64 scopeid 0x20<link>
ether 70:db:98:70:2f:6e txqueuelen 1000 (Ethernet)
RX packets 3373533 bytes 5021452007 (4.6 GiB)
RX errors 0 dropped 3945 overruns 0 frame 0
TX packets 337841 bytes 30441490 (29.0 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
236
Support Commands
support show iostat
support show iostat
To display the I/O statistics of block devices, use the support show iostat command in privileged EXEC
mode.
support show iostat
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show iostat
Major Minor Device Reads Reads Sectors Time (ms) Writes Writes Sectors Time (ms) IOs In
Time (ms) Weighted
Number Number Name Successful Merged Read Reading Completed Merged Written Writing Progress
Doing IOs Time(ms) IOs
-----------------------------------------------------------------------------------------------------------------------------------------
8 0 sda 34721 8 938752 149830 2713238 302897 37631784 84086836 0 1098844 84236605
8 1 sda1 52 0 416 156 0 0 0 0 0 156 156
8 2 sda2 437 0 49322 629 7 1 64 0 0 469 628
8 3 sda3 34054 8 884766 148345 2713231 302896 37631720 84086836 0 1098524 84238309
253 0 dm-0 17693 0 564042 101847 66698 0 694744 74520 0 40719 176366
253 1 dm-1 218 0 4456 832 0 0 0 0 0 810 832
253 2 dm-2 15066 0 261514 42646 2911495 0 36585456 84848114 0 1056312 84891060
253 3 dm-3 1055 0 53730 4699 37951 0 351520 246240 0 20556 250939
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
237
Support Commands
support show ipsec
support show ipsec
To display the IPsec session details, use the support show ipsec command in privileged EXEC mode.
support show ipsec
Command Default Information about IPsec session details is displayed.
Command Modes Privileged EXEC (#)
Command History Release Modification
4.5.1 This command was introduced.
Example
The following is a sample output of the support show ipsec command:
nfvis# support show ipsec
Status of IKE charon daemon (strongSwan 5.7.1, Linux 3.10.0-1062.4.1.el7.x86_64, x86_64):
uptime: 13 minutes, since Mar 24 22:35:31 2021
malloc: sbrk 2822144, mmap 0, used 630752, free 2191392
worker threads: 11 of 16 idle, 5/0/0/0 working, job queue: 0/0/0/0, scheduled: 2
loaded plugins: charon pkcs11 tpm aesni aes des rc2 sha2 sha1 md4 md5 mgf1 random nonce
x509 revocation constraints acert pubkey pkcs1 pkcs7 pkcs8 pkcs12 pgp dnskey sshkey pem
openssl gcrypt fips-prf gmp curve25519 chapoly xcbc cmac hmac ctr ccm gcm curl attr
kernel-netlink resolve socket-default stroke vici updown eap-identity eap-sim eap-aka
eap-aka-3gpp eap-aka-3gpp2 eap-md5 eap-gtc eap-mschapv2 eap-dynamic eap-radius eap-tls
eap-ttls eap-peap xauth-generic xauth-eap xauth-pam xauth-noauth dhcp led duplicheck unity
counters
Listening IP addresses:
192.168.1.1
172.25.221.110
192.168.50.1
192.168.10.11
169.254.1.1
Connections:
test: 172.25.221.110...10.30.1.113 IKEv2
test: local: [172.25.221.110] uses pre-shared key authentication
test: remote: [10.30.1.113] uses pre-shared key authentication
test: child: 0.0.0.0/0 === 0.0.0.0/0 TUNNEL
Security Associations (1 up, 0 connecting):
test[1]: ESTABLISHED 13 minutes ago,
172.25.221.110[172.25.221.110]...10.30.1.113[10.30.1.113]
test[1]: IKEv2 SPIs: 9371ee51ac1b436d_i* 52e341d1eb29f7bf_r, rekeying in 23 hours
test[1]: IKE proposal: AES_CBC_256/HMAC_SHA2_512_256/PRF_HMAC_SHA2_512/MODP_2048
test{1}: INSTALLED, TUNNEL, reqid 1, ESP SPIs: c916a993_i 7bb99a5e_o
test{1}: AES_CBC_256/HMAC_SHA2_512_256, 8393 bytes_i (111 pkts, 1s ago), 8485
bytes_o (112 pkts, 1s ago), rekeying in 40 minutes
test{1}: 0.0.0.0/0 === 0.0.0.0/0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
238
Support Commands
support show loadavg
support show loadavg
To display the load average of CPU and IO over 1, 5, and 10 minute period, use the support show loadavg
command in privileged EXEC mode.
support show loadavg
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show loadavg
Avg CPU and IO Utilization (1m) : 0.40
Avg CPU and IO Utilization (5m) : 0.36
Avg CPU and IO Utilization (10m) : 0.33
Running/Total Num of Processes : 1/678
Last Proccess ID Used : 13411
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
239
Support Commands
support show meminfo
support show meminfo
To display the information about system's RAM usage, use the support show meminfo command in privileged
EXEC mode.
support show meminfo
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show meminfo
MemTotal: 131748668 kB
MemFree: 123779264 kB
MemAvailable: 128225916 kB
Buffers: 11800 kB
Cached: 4887312 kB
SwapCached: 0 kB
Active: 1842792 kB
Inactive: 4658692 kB
Active(anon): 1613936 kB
Inactive(anon): 13644 kB
Active(file): 228856 kB
Inactive(file): 4645048 kB
Unevictable: 184888 kB
Mlocked: 184888 kB
SwapTotal: 16777212 kB
SwapFree: 16777212 kB
Dirty: 5112 kB
Writeback: 0 kB
AnonPages: 1787960 kB
Mapped: 95852 kB
Shmem: 16156 kB
Slab: 240824 kB
SReclaimable: 172504 kB
SUnreclaim: 68320 kB
KernelStack: 11536 kB
PageTables: 22360 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
WritebackTmp: 0 kB
CommitLimit: 82651544 kB
Committed_AS: 7245188 kB
VmallocTotal: 34359738367 kB
VmallocUsed: 507704 kB
VmallocChunk: 34291843068 kB
HardwareCorrupted: 0 kB
AnonHugePages: 1208320 kB
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
240
Support Commands
support show meminfo
HugePages_Total: 0
HugePages_Free: 0
HugePages_Rsvd: 0
HugePages_Surp: 0
Hugepagesize: 2048 kB
DirectMap4k: 171680 kB
DirectMap2M: 7055360 kB
DirectMap1G: 128974848 kB
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
241
Support Commands
support show netstattcp
support show netstattcp
To display the network connection and protocol statistics information for TCP, use the support show netstattcp
command in privileged EXEC mode.
support show netstattcp
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show netstattcp
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address Foreign Address State
tcp 0 0 127.0.0.1:7878 0.0.0.0:* LISTEN
tcp 0 0 127.0.0.1:199 0.0.0.0:* LISTEN
tcp 0 0 127.0.0.1:2023 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:8008 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:5900 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:22222 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN
tcp 0 0 127.0.0.1:4565 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:8888 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:443 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:830 0.0.0.0:* LISTEN
tcp 0 0 127.0.0.1:8000 0.0.0.0:* LISTEN
tcp6 0 0 :::8001 :::* LISTEN
tcp6 0 0 127.0.0.1:8005 :::* LISTEN
tcp6 0 0 ::1:7878 :::* LISTEN
tcp6 0 0 :::8009 :::* LISTEN
tcp6 0 0 :::22222 :::* LISTEN
tcp6 0 0 :::111 :::* LISTEN
tcp6 0 0 :::8080 :::* LISTEN
tcp6 0 0 :::80 :::* LISTEN
tcp6 0 0 :::8081 :::* LISTEN
tcp6 0 0 :::22 :::* LISTEN
tcp6 0 0 :::443 :::* LISTEN
tcp6 0 0 :::830 :::* LISTEN
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
242
Support Commands
support show netstatudp
support show netstatudp
To display the network connection and protocol statistics information for UDP, use the support show
netstatudp command in privileged EXEC mode.
support show netstatudp
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show netstatudp
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address Foreign Address State
udp 0 0 0.0.0.0:161 0.0.0.0:*
udp 0 0 127.0.0.1:323 0.0.0.0:*
udp 0 0 0.0.0.0:1610 0.0.0.0:*
udp6 0 0 ::1:323 :::*
udp6 0 0 ::1:1610 :::*
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
243
Support Commands
support show procstat
support show procstat
To display the statistics information for kernel or system, use the support show procstat command in privileged
EXEC mode.
support show procstat
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show procstat
cpu 155096 1 303421 267304458 50402 0 4774 0 52078 0
cpu0 29046 0 43045 6607705 3121 0 1175 0 0 0
cpu1 27238 0 39353 6562272 1857 0 2558 0 0 0
cpu2 0 0 231 6697805 0 0 0 0 0 0
cpu3 0 0 231 6698222 0 0 0 0 0 0
cpu4 0 0 231 6698222 0 0 0 0 0 0
cpu5 0 0 231 6698222 0 0 0 0 0 0
cpu6 0 0 231 6698222 0 0 0 0 0 0
cpu7 0 0 231 6698221 0 0 0 0 0 0
cpu8 0 0 231 6698221 0 0 0 0 0 0
cpu9 0 0 231 6698221 0 0 0 0 0 0
cpu10 0 0 262 6697886 0 0 0 0 0 0
cpu11 0 0 231 6698214 0 0 0 0 0 0
cpu12 0 0 231 6698213 0 0 0 0 0 0
cpu13 0 0 231 6698213 0 0 0 0 0 0
cpu14 0 0 231 6698212 0 0 0 0 0 0
cpu15 0 0 231 6698212 0 0 0 0 0 0
cpu16 0 0 231 6698212 0 0 0 0 0 0
cpu17 0 0 231 6698211 0 0 0 0 0 0
cpu18 0 0 231 6698211 0 0 0 0 0 0
cpu19 52484 0 27416 6600223 63 0 41 0 52078 0
cpu20 22792 0 95509 6572676 1530 0 368 0 0 0
cpu21 23533 0 89953 6524896 43829 0 631 0 0 0
cpu22 0 0 231 6698210 0 0 0 0 0 0
cpu23 0 0 231 6698210 0 0 0 0 0 0
cpu24 0 0 231 6698209 0 0 0 0 0 0
cpu25 0 0 231 6698209 0 0 0 0 0 0
cpu26 0 0 231 6698209 0 0 0 0 0 0
cpu27 0 0 231 6698209 0 0 0 0 0 0
cpu28 0 0 231 6698208 0 0 0 0 0 0
cpu29 0 0 231 6698207 0 0 0 0 0 0
cpu30 0 0 231 6698207 0 0 0 0 0 0
cpu31 0 0 231 6698207 0 0 0 0 0 0
cpu32 0 0 231 6698206 0 0 0 0 0 0
cpu33 0 0 231 6698206 0 0 0 0 0 0
cpu34 0 0 231 6698206 0 0 0 0 0 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
244
Support Commands
support show procstat
cpu35 0 0 231 6698205 0 0 0 0 0 0
cpu36 0 0 231 6698205 0 0 0 0 0 0
cpu37 0 0 231 6698204 0 0 0 0 0 0
cpu38 0 0 231 6698204 0 0 0 0 0 0
cpu39 0 0 231 6698204 0 0 0 0 0 0
intr 71282795 154 0 0 0 890 0 0 0 1 148338 0 0 0 0 0 0 0 0 129 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 162766 64744
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 533 25119 2256492 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 171740 2860624
452569 36061 40063 97867 61120 302923 0 0 33470 33470 33470 33470 33470 33470 33470 33470
0 33469 33469 33469 33469
33469 33469 33469 33469 0 0 33469 33469 33469 33469 33469 33469 33469 33469 0 0 33468 33468
33468 33468 33468 33468
33468 33468 0 0 33468 33468 33468 33468 33468 33468 33468 33468 33433 33433 33433 33433
33433 33433 33433 33433 33433
33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433
33433 33433 33433 33433 33433
33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 0 0 33433 33433 33433
33433 33433 33433 33433 33433
33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433
33433 33433 33433 33433 33433
33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 33433 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ctxt 107838268
btime 1510762560
processes 162648
procs_running 1
procs_blocked 0
softirq 73632593 9 31179219 13427 11364643 2471015 0 686 11744081 0 16859513
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
245
Support Commands
support show route
support show route
To display the route netstat information, use the support show route command in privileged EXEC mode.
support show route
Syntax Description table-id (Optional) Specifies the table ID.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show route ?
Possible completions:
Linux routing table number to display | <cr>
nfvis# support show route 220
90.90.90.1 dev ipsec0 scope link
91.91.91.0/24 dev ipsec0 proto bird scope link
92.92.92.0/24 dev ipsec0 proto bird scope link
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
246
Support Commands
support show snmp
support show snmp
To display the IP, ICMP, TCP, and UDP MIB information for SNMP agent, use the support show snmp
command in privileged EXEC mode.
support show snmp
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show snmp
Ip: Forwarding DefaultTTL InReceives InHdrErrors InAddrErrors ForwDatagrams InUnknownProtos
InDiscards InDelivers OutRequests
OutDiscards OutNoRoutes ReasmTimeout ReasmReqds ReasmOKs ReasmFails FragOKs FragFails
FragCreates
Ip: 1 64 6869229 0 0 0 0 0 3944160 3939158 407 0 0 0 0 0 0 0 0
Icmp: InMsgs InErrors InCsumErrors InDestUnreachs InTimeExcds InParmProbs InSrcQuenchs
InRedirects InEchos InEchoReps InTimestamps
InTimestampReps InAddrMasks InAddrMaskReps OutMsgs OutErrors OutDestUnreachs OutTimeExcds
OutParmProbs OutSrcQuenchs OutRedirects
OutEchos OutEchoReps OutTimestamps OutTimestampReps OutAddrMasks OutAddrMaskReps
Icmp: 9732 0 0 9732 0 0 0 0 0 0 0 0 0 0 9735 0 9735 0 0 0 0 0 0 0 0 0 0
IcmpMsg: InType3 OutType3
IcmpMsg: 9732 9735
Tcp: RtoAlgorithm RtoMin RtoMax MaxConn ActiveOpens PassiveOpens AttemptFails EstabResets
CurrEstab InSegs OutSegs RetransSegs
InErrs OutRsts InCsumErrors
Tcp: 1 200 120000 -1 15203 14161 1119 7 402 3931354 3927811 489 0 1127 0
Udp: InDatagrams NoPorts InErrors OutDatagrams RcvbufErrors SndbufErrors InCsumErrors
Udp: 0 9732 0 9732 0 0 0
UdpLite: InDatagrams NoPorts InErrors OutDatagrams RcvbufErrors SndbufErrors InCsumErrors
UdpLite: 0 0 0 0 0 0 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
247
Support Commands
support show system-version
support show system-version
To display the information about the system version, use the support show system-version command in
privileged EXEC mode.
support show system-version
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show system-version
Linux version 3.10.0-514.21.1.el7.x86_64 ([email protected]) (gcc version 4.8.5 20150623
(Red Hat 4.8.5-11) (GCC) )
#1 SMP Tue Aug 8 14:23:12 IST 2017
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
248
Support Commands
support show system-hostname
support show system-hostname
To display the system host name, use the support show system-hostname command in privileged EXEC
mode.
support show system-hostname
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support show system-hostname
nfvis
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
249
Support Commands
support virsh all-info
support virsh all-info
To display the output of all supported virsh commands, use the support virsh all-info command in privileged
EXEC mode.
support virsh all-info
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh all-info
support virsh list
Id Name State
----------------------------------------------------
1 1510117366.RouterUnmon running
2 1510085877.ubuntu running
3 1510095552.ROUTER running
4 isr1-dep.isr1-vg running
support virsh dumpxml 1
<domain type='kvm' id='1'>
<name>1510117366.RouterUnmon</name>
<uuid>2329b9ff-2a77-4e20-9cad-a5a5984bd4ba</uuid>
<memory unit='KiB'>2359296</memory>
<currentMemory unit='KiB'>2359296</currentMemory>
<vcpu placement='static' current='2'>8</vcpu>
<cputune>
<vcpupin vcpu='0' cpuset='12'/>
<vcpupin vcpu='1' cpuset='11'/>
<emulatorpin cpuset='11-12'/>
</cputune>
<resource>
<partition>/machine</partition>
</resource>
<os>
<type arch='x86_64' machine='pc-i440fx-rhel7.0.0'>hvm</type>
<boot dev='hd'/>
</os>
<features>
<acpi/>
<apic/>
<pae/>
</features>
<cpu mode='host-passthrough'/>
<clock offset='utc'/>
<on_poweroff>restart</on_poweroff>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
250
Support Commands
support virsh all-info
<on_reboot>restart</on_reboot>
<on_crash>destroy</on_crash>
<devices>
<emulator>/usr/libexec/qemu-kvm</emulator>
<disk type='file' device='disk'>
<driver name='qemu' type='qcow2' cache='writethrough'/>
<source
file='/data/cisco/vm_lifecycle/volumes/2329b9ff-2a77-4e20-9cad-a5a5984bd4ba_0.img'/>
<backingStore type='file' index='1'>
<format type='qcow2'/>
<source
file='/data/cisco/vm_lifecycle/volumes/isrv-universalk9.16.06.01-vga.qcow2_0.img'/>
<backingStore/>
</backingStore>
<target dev='vda' bus='virtio'/>
<alias name='virtio-disk0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/>
</disk>
<controller type='usb' index='0'>
<alias name='usb'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x2'/>
</controller>
<controller type='pci' index='0' model='pci-root'>
<alias name='pci.0'/>
</controller>
<interface type='bridge'>
<mac address='52:54:00:f7:06:89'/>
<source network='lan-net' bridge='lan-br'/>
<virtualport type='openvswitch'>
<parameters interfaceid='98b0908f-8ddc-4800-b970-b1a902f2f1ac'/>
</virtualport>
<target dev='vnic8'/>
<model type='virtio'/>
<alias name='net0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/>
</interface>
<interface type='bridge'>
<mac address='52:54:00:52:67:ba'/>
<source network='wan-net' bridge='wan-br'/>
<virtualport type='openvswitch'>
<parameters interfaceid='b42b7f81-37a8-45c5-b468-ec60074a5ec4'/>
</virtualport>
<target dev='vnic9'/>
<model type='virtio'/>
<alias name='net1'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/>
</interface>
<input type='mouse' bus='ps2'>
<alias name='input0'/>
</input>
<input type='tablet' bus='usb'>
<alias name='input1'/>
<address type='usb' bus='0' port='1'/>
</input>
<input type='keyboard' bus='ps2'>
<alias name='input2'/>
</input>
<graphics type='vnc' port='5900' autoport='yes' listen='0.0.0.0'>
<listen type='address' address='0.0.0.0'/>
</graphics>
<video>
<model type='cirrus' vram='16384' heads='1' primary='yes'/>
<alias name='video0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
251
Support Commands
support virsh all-info
</video>
<memballoon model='none'/>
</devices>
<seclabel type='dynamic' model='selinux' relabel='yes'>
<label>system_u:system_r:svirt_t:s0:c379,c571</label>
<imagelabel>system_u:object_r:svirt_image_t:s0:c379,c571</imagelabel>
</seclabel>
<seclabel type='dynamic' model='dac' relabel='yes'>
<label>+107:+107</label>
<imagelabel>+107:+107</imagelabel>
</seclabel>
</domain>
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
252
Support Commands
support virsh capabilities
support virsh capabilities
To display the host capabilities, use the support virsh capabilities command in privileged EXEC mode.
support virsh capabilities
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh capabilities
<capabilities>
<host>
<uuid>eb7c9ce9-9df9-3142-898b-c84a16b10706</uuid>
<cpu>
<arch>x86_64</arch>
<model>Broadwell</model>
<vendor>Intel</vendor>
<topology sockets='1' cores='10' threads='2'/>
<feature name='vme'/>
<feature name='ds'/>
<feature name='acpi'/>
<feature name='ss'/>
<feature name='ht'/>
<feature name='tm'/>
<feature name='pbe'/>
<feature name='dtes64'/>
<feature name='monitor'/>
<feature name='ds_cpl'/>
<feature name='vmx'/>
<feature name='smx'/>
<feature name='est'/>
<feature name='tm2'/>
<feature name='xtpr'/>
<feature name='pdcm'/>
<feature name='dca'/>
<feature name='osxsave'/>
<feature name='f16c'/>
<feature name='rdrand'/>
<feature name='arat'/>
<feature name='tsc_adjust'/>
<feature name='cmt'/>
<feature name='xsaveopt'/>
<feature name='mbm_total'/>
<feature name='mbm_local'/>
<feature name='pdpe1gb'/>
<feature name='abm'/>
<feature name='invtsc'/>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
253
Support Commands
support virsh capabilities
<pages unit='KiB' size='4'/>
<pages unit='KiB' size='2048'/>
<pages unit='KiB' size='1048576'/>
</cpu>
<power_management>
<suspend_mem/>
<suspend_disk/>
<suspend_hybrid/>
</power_management>
<migration_features>
<live/>
<uri_transports>
<uri_transport>tcp</uri_transport>
<uri_transport>rdma</uri_transport>
</uri_transports>
</migration_features>
<topology>
<cells num='2'>
<cell id='0'>
<memory unit='KiB'>66995472</memory>
<pages unit='KiB' size='4'>16748868</pages>
<pages unit='KiB' size='2048'>0</pages>
<pages unit='KiB' size='1048576'>0</pages>
<distances>
<sibling id='0' value='10'/>
<sibling id='1' value='21'/>
</distances>
<cpus num='20'>
<cpu id='0' socket_id='0' core_id='0' siblings='0,20'/>
<cpu id='1' socket_id='0' core_id='1' siblings='1,21'/>
<cpu id='2' socket_id='0' core_id='2' siblings='2,22'/>
<cpu id='3' socket_id='0' core_id='3' siblings='3,23'/>
<cpu id='4' socket_id='0' core_id='4' siblings='4,24'/>
<cpu id='5' socket_id='0' core_id='8' siblings='5,25'/>
<cpu id='6' socket_id='0' core_id='9' siblings='6,26'/>
<cpu id='7' socket_id='0' core_id='10' siblings='7,27'/>
<cpu id='8' socket_id='0' core_id='11' siblings='8,28'/>
<cpu id='9' socket_id='0' core_id='12' siblings='9,29'/>
<cpu id='20' socket_id='0' core_id='0' siblings='0,20'/>
<cpu id='21' socket_id='0' core_id='1' siblings='1,21'/>
<cpu id='22' socket_id='0' core_id='2' siblings='2,22'/>
<cpu id='23' socket_id='0' core_id='3' siblings='3,23'/>
<cpu id='24' socket_id='0' core_id='4' siblings='4,24'/>
<cpu id='25' socket_id='0' core_id='8' siblings='5,25'/>
<cpu id='26' socket_id='0' core_id='9' siblings='6,26'/>
<cpu id='27' socket_id='0' core_id='10' siblings='7,27'/>
<cpu id='28' socket_id='0' core_id='11' siblings='8,28'/>
<cpu id='29' socket_id='0' core_id='12' siblings='9,29'/>
</cpus>
</cell>
<cell id='1'>
<memory unit='KiB'>67108864</memory>
<pages unit='KiB' size='4'>16777216</pages>
<pages unit='KiB' size='2048'>0</pages>
<pages unit='KiB' size='1048576'>0</pages>
<distances>
<sibling id='0' value='21'/>
<sibling id='1' value='10'/>
</distances>
<cpus num='20'>
<cpu id='10' socket_id='1' core_id='0' siblings='10,30'/>
<cpu id='11' socket_id='1' core_id='1' siblings='11,31'/>
<cpu id='12' socket_id='1' core_id='2' siblings='12,32'/>
<cpu id='13' socket_id='1' core_id='3' siblings='13,33'/>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
254
Support Commands
support virsh capabilities
<cpu id='14' socket_id='1' core_id='4' siblings='14,34'/>
<cpu id='15' socket_id='1' core_id='8' siblings='15,35'/>
<cpu id='16' socket_id='1' core_id='9' siblings='16,36'/>
<cpu id='17' socket_id='1' core_id='10' siblings='17,37'/>
<cpu id='18' socket_id='1' core_id='11' siblings='18,38'/>
<cpu id='19' socket_id='1' core_id='12' siblings='19,39'/>
<cpu id='30' socket_id='1' core_id='0' siblings='10,30'/>
<cpu id='31' socket_id='1' core_id='1' siblings='11,31'/>
<cpu id='32' socket_id='1' core_id='2' siblings='12,32'/>
<cpu id='33' socket_id='1' core_id='3' siblings='13,33'/>
<cpu id='34' socket_id='1' core_id='4' siblings='14,34'/>
<cpu id='35' socket_id='1' core_id='8' siblings='15,35'/>
<cpu id='36' socket_id='1' core_id='9' siblings='16,36'/>
<cpu id='37' socket_id='1' core_id='10' siblings='17,37'/>
<cpu id='38' socket_id='1' core_id='11' siblings='18,38'/>
<cpu id='39' socket_id='1' core_id='12' siblings='19,39'/>
</cpus>
</cell>
</cells>
</topology>
<secmodel>
<model>selinux</model>
<doi>0</doi>
<baselabel type='kvm'>system_u:system_r:svirt_t:s0</baselabel>
<baselabel type='qemu'>system_u:system_r:svirt_tcg_t:s0</baselabel>
</secmodel>
<secmodel>
<model>dac</model>
<doi>0</doi>
<baselabel type='kvm'>+107:+107</baselabel>
<baselabel type='qemu'>+107:+107</baselabel>
</secmodel>
</host>
<guest>
<os_type>hvm</os_type>
<arch name='i686'>
<wordsize>32</wordsize>
<emulator>/usr/libexec/qemu-kvm</emulator>
<machine maxCpus='240'>pc-i440fx-rhel7.0.0</machine>
<machine canonical='pc-i440fx-rhel7.0.0' maxCpus='240'>pc</machine>
<machine maxCpus='240'>rhel6.0.0</machine>
<machine maxCpus='240'>rhel6.1.0</machine>
<machine maxCpus='240'>rhel6.2.0</machine>
<machine maxCpus='240'>rhel6.3.0</machine>
<machine maxCpus='240'>rhel6.4.0</machine>
<machine maxCpus='240'>rhel6.5.0</machine>
<machine maxCpus='240'>rhel6.6.0</machine>
<domain type='qemu'/>
<domain type='kvm'>
<emulator>/usr/libexec/qemu-kvm</emulator>
</domain>
</arch>
<features>
<cpuselection/>
<deviceboot/>
<disksnapshot default='off' toggle='no'/>
<acpi default='on' toggle='yes'/>
<apic default='on' toggle='no'/>
<pae/>
<nonpae/>
</features>
</guest>
<guest>
<os_type>hvm</os_type>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
255
Support Commands
support virsh capabilities
<arch name='x86_64'>
<wordsize>64</wordsize>
<emulator>/usr/libexec/qemu-kvm</emulator>
<machine maxCpus='240'>pc-i440fx-rhel7.0.0</machine>
<machine canonical='pc-i440fx-rhel7.0.0' maxCpus='240'>pc</machine>
<machine maxCpus='240'>rhel6.0.0</machine>
<machine maxCpus='240'>rhel6.1.0</machine>
<machine maxCpus='240'>rhel6.2.0</machine>
<machine maxCpus='240'>rhel6.3.0</machine>
<machine maxCpus='240'>rhel6.4.0</machine>
<machine maxCpus='240'>rhel6.5.0</machine>
<machine maxCpus='240'>rhel6.6.0</machine>
<domain type='qemu'/>
<domain type='kvm'>
<emulator>/usr/libexec/qemu-kvm</emulator>
</domain>
</arch>
<features>
<cpuselection/>
<deviceboot/>
<disksnapshot default='off' toggle='no'/>
<acpi default='on' toggle='yes'/>
<apic default='on' toggle='no'/>
</features>
</guest>
</capabilities>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
256
Support Commands
support virsh cpu-stats
support virsh cpu-stats
To display the CPU statistics for a domain, use the support virsh cpu-stats command in privileged EXEC
mode.
support virsh cpu-stats domain
Syntax Description domain Specifies the domain name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh cpu-stats 1512149985.ROUTER
Time used by the domain:
cpu_time : 55311955404 ns
system_time : 3910000000 ns
user_time : 810000000 ns
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
257
Support Commands
support virsh domiflist
support virsh domiflist
To display the list of interfaces in a domain, use the support virsh domiflist command in privileged EXEC
mode.
support virsh domiflist domain
Syntax Description domain Specifies the domain name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh domiflist 2
Interface Type Source Model MAC
-------------------------------------------------------
vnic2 bridge wan-net virtio 52:54:00:db:4d:10
vnic3 bridge lan-net virtio 52:54:00:8a:58:f5
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
258
Support Commands
support virsh dumpxml
support virsh dumpxml
To display the VM XML dump of the configuration file, use the support virsh dumpxml command in
privileged EXEC mode.
support virsh dumpxml domain
Syntax Description domain Specifies the name or ID of the domain.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh dumpxml 2
<domain type='kvm' id='2'>
<name>1505948272.vmdk</name>
<uuid>285b8c3f-9f10-4e6b-b9bc-e87caaf7d877</uuid>
<memory unit='KiB'>4456448</memory>
<currentMemory unit='KiB'>4456448</currentMemory>
<vcpu placement='static' current='2'>8</vcpu>
<cputune>
<vcpupin vcpu='0' cpuset='17'/>
<vcpupin vcpu='1' cpuset='16'/>
</cputune>
<resource>
<partition>/machine</partition>
</resource>
<os>
<type arch='x86_64' machine='pc-i440fx-rhel7.0.0'>hvm</type>
<boot dev='hd'/>
</os>
<features>
<acpi/>
<apic/>
<pae/>
</features>
<cpu mode='host-passthrough'/>
<clock offset='utc'/>
<on_poweroff>restart</on_poweroff>
<on_reboot>restart</on_reboot>
<on_crash>destroy</on_crash>
<devices>
<emulator>/usr/libexec/qemu-kvm</emulator>
<disk type='file' device='disk'>
<driver name='qemu' type='qcow2' cache='writethrough'/>
<source
file='/data/cisco/vm_lifecycle/volumes/285b8c3f-9f10-4e6b-b9bc-e87caaf7d877_0.img'/>
<backingStore type='file' index='1'>
<format type='qcow2'/>
<source file='/data/cisco/vm_lifecycle/volumes/vwlc.vmdk_0.img'/>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
259
Support Commands
support virsh dumpxml
<backingStore/>
</backingStore>
<target dev='vda' bus='virtio'/>
<alias name='virtio-disk0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/>
</disk>
<controller type='usb' index='0'>
<alias name='usb'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x2'/>
</controller>
<controller type='pci' index='0' model='pci-root'>
<alias name='pci.0'/>
</controller>
<interface type='bridge'>
<mac address='52:54:00:db:4d:10'/>
<source network='wan-net' bridge='wan-br'/>
<virtualport type='openvswitch'>
<parameters interfaceid='ad1fb82a-b6c3-4f39-adc0-72788820e798'/>
</virtualport>
<target dev='vnic2'/>
<model type='virtio'/>
<alias name='net0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/>
</interface>
<interface type='bridge'>
<mac address='52:54:00:8a:58:f5'/>
<source network='lan-net' bridge='lan-br'/>
<virtualport type='openvswitch'>
<parameters interfaceid='58070073-58ab-4ec6-92e3-81da3f7468ad'/>
</virtualport>
<target dev='vnic3'/>
<model type='virtio'/>
<alias name='net1'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/>
</interface>
<input type='mouse' bus='ps2'>
<alias name='input0'/>
</input>
<input type='tablet' bus='usb'>
<alias name='input1'/>
<address type='usb' bus='0' port='1'/>
</input>
<input type='keyboard' bus='ps2'>
<alias name='input2'/>
</input>
<graphics type='vnc' port='5901' autoport='yes' listen='0.0.0.0'>
<listen type='address' address='0.0.0.0'/>
</graphics>
<video>
<model type='cirrus' vram='16384' heads='1' primary='yes'/>
<alias name='video0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/>
</video>
<memballoon model='none'/>
</devices>
<seclabel type='dynamic' model='selinux' relabel='yes'>
<label>system_u:system_r:svirt_t:s0:c726,c919</label>
<imagelabel>system_u:object_r:svirt_image_t:s0:c726,c919</imagelabel>
</seclabel>
<seclabel type='dynamic' model='dac' relabel='yes'>
<label>+107:+107</label>
<imagelabel>+107:+107</imagelabel>
</seclabel>
</domain>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
260
Support Commands
support virsh iface-list
support virsh iface-list
To display a list of interfaces on the host, use the support virsh iface-list command in privileged EXEC
mode.
support virsh iface-list
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh iface-list
Name State MAC Address
---------------------------------------------------
eth0 active 70:db:98:70:2f:6e
int-mgmt-net-br active c6:13:e5:4d:e1:46
lan-br active 70:db:98:07:1f:35
lo active 00:00:00:00:00:00
wan-br active 70:db:98:70:2f:6e
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
261
Support Commands
support virsh iface-dumpxml
support virsh iface-dumpxml
To display the XML dump of an interface, use the support virsh iface-dumpxml command in privileged
EXEC mode.
support virsh iface-dumpxml interface
Syntax Description interface Specifies the interface name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh iface-dumpxml wan-br
<interface type='ethernet' name='wan-br'>
<protocol family='ipv4'>
<ip address='172.19.181.196' prefix='24'/>
</protocol>
<protocol family='ipv6'>
<ip address='2001:420:30d:200:72db:98ff:fe70:2f6e' prefix='64'/>
<ip address='2001:420:30d:201:ffff:ffff:fffd:fa50' prefix='64'/>
<ip address='fe80::72db:98ff:fe70:2f6e' prefix='64'/>
</protocol>
<link state='unknown'/>
<mac address='70:db:98:70:2f:6e'/>
</interface>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
262
Support Commands
support virsh list
support virsh list
To display a list of VM domains provisioned in the system, use the support virsh list command in privileged
EXEC mode.
support virsh list
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh list
Id Name State
----------------------------------------------------
2 1505948272.vmdk running
3 1505947515.raw running
- 1505946928.iso shut off
- 1505948274.iso2 shut off
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
263
Support Commands
support virsh memory-stats
support virsh memory-stats
To display the memory statistics for a domain, use the support virsh memory-stats command in privileged
EXEC mode.
support virsh memory-stats domain
Syntax Description domain Specifies the domain name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh memory-stats name 1510771542.OTHER
Memory used:
rss: 119808 KB
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
264
Support Commands
support virsh net-dumpxml
support virsh net-dumpxml
To display the XML dump of a network, use the support virsh net-dumpxml command in privileged EXEC
mode.
support virsh net-dumpxml network
Syntax Description network Specifies the network name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh net-dumpxml wan-net
<network connections='1'>
<name>wan-net</name>
<uuid>e51f65c5-fec4-4b3c-a7cd-540b748bde57</uuid>
<forward mode='bridge'/>
<bridge name='wan-br'/>
<virtualport type='openvswitch'/>
</network>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
265
Support Commands
support virsh net-list
support virsh net-list
To display a list of networks in the host, use the support virsh net-list command in privileged EXEC mode.
support virsh net-list
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh net-list
Name State Autostart Persistent
----------------------------------------------------------
int-mgmt-net active yes yes
lan-net active yes yes
wan-net active yes yes
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
266
Support Commands
support virsh net-info
support virsh net-info
To display information about a network, use the support virsh net-info command in privileged EXEC mode.
support virsh net-info network
Syntax Description network Specifies the name of the network.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh net-info wan-net
Name: wan-net
UUID: e51f65c5-fec4-4b3c-a7cd-540b748bde57
Active: yes
Persistent: yes
Autostart: yes
Bridge: wan-br
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
267
Support Commands
support virsh nodecpustats
support virsh nodecpustats
To display the system-wide CPU statistics, use the support virsh nodecpustats command in privileged EXEC
mode.
support virsh nodecpustats
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh nodecpustats
usage: 0.1%
user: 0.0%
system: 0.0%
idle: 100.0%
iowait: 0.0%
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
268
Support Commands
support virsh pool-list
support virsh pool-list
To display a list of all storage pools in the system, use the support virsh pool-list command in privileged
EXEC mode.
support virsh pool-list
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh pool-list
Name State Autostart
-------------------------------------------
cisco_datastore1 active no
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
269
Support Commands
support virsh pool-dumpxml
support virsh pool-dumpxml
To display the XML dump of a storage pool, use the support virsh pool-dumpxml command in privileged
EXEC mode.
support virsh pool-dumpxml poolname
Syntax Description poolname Specifies the pool name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh pool-dumpxml cisco_datastore1
<pool type='dir'>
<name>cisco_datastore1</name>
<uuid>51487524-16fe-40c9-a598-6384c914e191</uuid>
<capacity unit='bytes'>2304488226816</capacity>
<allocation unit='bytes'>256696770560</allocation>
<available unit='bytes'>2047791456256</available>
<source>
</source>
<target>
<path>/data/cisco/vm_lifecycle/volumes</path>
<permissions>
<mode>0755</mode>
<owner>0</owner>
<group>0</group>
<label>system_u:object_r:etc_runtime_t:s0</label>
</permissions>
</target>
</pool>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
270
Support Commands
support virsh sys-info
support virsh sys-info
To display the system information, use the support virsh sys-info command in privileged EXEC mode.
support virsh sys-info
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh sys-info
Sys info: <sysinfo type='smbios'>
<bios>
<entry name='vendor'>Cisco Systems, Inc.</entry>
<entry name='version'>C220M4.2.0.13g.0.1113162259</entry>
<entry name='date'>11/13/2016</entry>
<entry name='release'>5.11</entry>
</bios>
<system>
<entry name='manufacturer'>Cisco Systems Inc</entry>
<entry name='product'>UCSC-C220-M4S</entry>
<entry name='version'>A0</entry>
<entry name='serial'>FCH2110V0DX</entry>
<entry name='uuid'>EB7C9CE9-9DF9-3142-898B-C84A16B10706</entry>
<entry name='sku'>Not Specified</entry>
<entry name='family'>Not Specified</entry>
</system>
<baseBoard>
<entry name='manufacturer'>Cisco Systems Inc</entry>
<entry name='product'>UCSC-C220-M4S</entry>
<entry name='version'>74-12419-02</entry>
<entry name='serial'>FCH2108JLC4</entry>
<entry name='asset'>Unknown</entry>
<entry name='location'>Not Specified</entry>
</baseBoard>
<processor>
<entry name='socket_destination'>CPU1</entry>
<entry name='type'>Central Processor</entry>
<entry name='family'>Xeon</entry>
<entry name='manufacturer'>Intel(R) Corporation</entry>
<entry name='signature'>Type 0, Family 6, Model 79, Stepping 1</entry>
<entry name='version'>Intel(R) Xeon(R) CPU E5-2630 v4 @ 2.20GHz</entry>
<entry name='external_clock'>100 MHz</entry>
<entry name='max_speed'>4000 MHz</entry>
<entry name='status'>Populated, Enabled</entry>
<entry name='serial_number'>Not Specified</entry>
<entry name='part_number'>Not Specified</entry>
</processor>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
271
Support Commands
support virsh sys-info
<processor>
<entry name='socket_destination'>CPU2</entry>
<entry name='type'>Central Processor</entry>
<entry name='family'>Xeon</entry>
<entry name='manufacturer'>Intel(R) Corporation</entry>
<entry name='signature'>Type 0, Family 6, Model 79, Stepping 1</entry>
<entry name='version'>Intel(R) Xeon(R) CPU E5-2630 v4 @ 2.20GHz</entry>
<entry name='external_clock'>100 MHz</entry>
<entry name='max_speed'>4000 MHz</entry>
<entry name='status'>Populated, Enabled</entry>
<entry name='serial_number'>Not Specified</entry>
<entry name='part_number'>Not Specified</entry>
</processor>
<memory_device>
<entry name='size'>16384 MB</entry>
<entry name='form_factor'>DIMM</entry>
<entry name='locator'>DIMM_A1</entry>
<entry name='bank_locator'>NODE 0 CHANNEL 0 DIMM 0</entry>
<entry name='type'>DDR4</entry>
<entry name='type_detail'>Registered (Buffered)</entry>
<entry name='speed'>2400 MHz</entry>
<entry name='manufacturer'>0xCE00</entry>
<entry name='serial_number'>34E462C9</entry>
<entry name='part_number'>M393A2K40BB1-CRC</entry>
</memory_device>
<memory_device>
<entry name='size'>16384 MB</entry>
<entry name='form_factor'>DIMM</entry>
<entry name='locator'>DIMM_B1</entry>
<entry name='bank_locator'>NODE 0 CHANNEL 1 DIMM 0</entry>
<entry name='type'>DDR4</entry>
<entry name='type_detail'>Registered (Buffered)</entry>
<entry name='speed'>2400 MHz</entry>
<entry name='manufacturer'>0xCE00</entry>
<entry name='serial_number'>34E4536B</entry>
<entry name='part_number'>M393A2K40BB1-CRC</entry>
</memory_device>
<memory_device>
<entry name='size'>16384 MB</entry>
<entry name='form_factor'>DIMM</entry>
<entry name='locator'>DIMM_C1</entry>
<entry name='bank_locator'>NODE 0 CHANNEL 2 DIMM 0</entry>
<entry name='type'>DDR4</entry>
<entry name='type_detail'>Registered (Buffered)</entry>
<entry name='speed'>2400 MHz</entry>
<entry name='manufacturer'>0xCE00</entry>
<entry name='serial_number'>34E4539A</entry>
<entry name='part_number'>M393A2K40BB1-CRC</entry>
</memory_device>
<memory_device>
<entry name='size'>16384 MB</entry>
<entry name='form_factor'>DIMM</entry>
<entry name='locator'>DIMM_D1</entry>
<entry name='bank_locator'>NODE 0 CHANNEL 3 DIMM 0</entry>
<entry name='type'>DDR4</entry>
<entry name='type_detail'>Registered (Buffered)</entry>
<entry name='speed'>2400 MHz</entry>
<entry name='manufacturer'>0xCE00</entry>
<entry name='serial_number'>34E4544B</entry>
<entry name='part_number'>M393A2K40BB1-CRC</entry>
</memory_device>
<memory_device>
<entry name='size'>16384 MB</entry>
<entry name='form_factor'>DIMM</entry>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
272
Support Commands
support virsh sys-info
<entry name='locator'>DIMM_E1</entry>
<entry name='bank_locator'>NODE 1 CHANNEL 0 DIMM 0</entry>
<entry name='type'>DDR4</entry>
<entry name='type_detail'>Registered (Buffered)</entry>
<entry name='speed'>2400 MHz</entry>
<entry name='manufacturer'>0xCE00</entry>
<entry name='serial_number'>34E468CE</entry>
<entry name='part_number'>M393A2K40BB1-CRC</entry>
</memory_device>
<memory_device>
<entry name='size'>16384 MB</entry>
<entry name='form_factor'>DIMM</entry>
<entry name='locator'>DIMM_F1</entry>
<entry name='bank_locator'>NODE 1 CHANNEL 1 DIMM 0</entry>
<entry name='type'>DDR4</entry>
<entry name='type_detail'>Registered (Buffered)</entry>
<entry name='speed'>2400 MHz</entry>
<entry name='manufacturer'>0xCE00</entry>
<entry name='serial_number'>34E44191</entry>
<entry name='part_number'>M393A2K40BB1-CRC</entry>
</memory_device>
<memory_device>
<entry name='size'>16384 MB</entry>
<entry name='form_factor'>DIMM</entry>
<entry name='locator'>DIMM_G1</entry>
<entry name='bank_locator'>NODE 1 CHANNEL 2 DIMM 0</entry>
<entry name='type'>DDR4</entry>
<entry name='type_detail'>Registered (Buffered)</entry>
<entry name='speed'>2400 MHz</entry>
<entry name='manufacturer'>0xCE00</entry>
<entry name='serial_number'>34E46927</entry>
<entry name='part_number'>M393A2K40BB1-CRC</entry>
</memory_device>
<memory_device>
<entry name='size'>16384 MB</entry>
<entry name='form_factor'>DIMM</entry>
<entry name='locator'>DIMM_H1</entry>
<entry name='bank_locator'>NODE 1 CHANNEL 3 DIMM 0</entry>
<entry name='type'>DDR4</entry>
<entry name='type_detail'>Registered (Buffered)</entry>
<entry name='speed'>2400 MHz</entry>
<entry name='manufacturer'>0xCE00</entry>
<entry name='serial_number'>34E468D0</entry>
<entry name='part_number'>M393A2K40BB1-CRC</entry>
</memory_device>
</sysinfo>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
273
Support Commands
support virsh vol-dumpxml
support virsh vol-dumpxml
To display the XML dump of a volume, use the support virsh vol-dumpxml command in privileged EXEC
mode.
support virsh vol-dumpxml poolname volumename
Syntax Description poolname Specifies the pool name.
volumename Specifies the volume name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh vol-dumpxml cisco_datastore1 vwlc.vmdk_0.img
<volume type='file'>
<name>vwlc.vmdk_0.img</name>
<key>/data/cisco/vm_lifecycle/volumes/vwlc.vmdk_0.img</key>
<source>
</source>
<capacity unit='bytes'>8589934592</capacity>
<allocation unit='bytes'>200704</allocation>
<target>
<path>/data/cisco/vm_lifecycle/volumes/vwlc.vmdk_0.img</path>
<format type='qcow2'/>
<permissions>
<mode>0600</mode>
<owner>107</owner>
<group>107</group>
<label>system_u:object_r:virt_content_t:s0</label>
</permissions>
<timestamps>
<atime>1505921732.573554833</atime>
<mtime>1505921559.789556401</mtime>
<ctime>1505921732.494554834</ctime>
</timestamps>
<compat>1.1</compat>
<features/>
</target>
</volume>
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
274
Support Commands
support virsh vol-list
support virsh vol-list
To display the list of interfaces in a domain, use the support virsh vol-list command in privileged EXEC
mode.
support virsh vol-list poolname
Syntax Description poolname Specifies the pool name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support virsh vol-list cisco_datastore1
Name Path
------------------------------------------------------------------------------
24ef7a32-4490-49ca-bbc8-c9a01ec20ae4_0.img
/data/cisco/vm_lifecycle/volumes/24ef7a32-4490-49ca-bbc8-c9a01ec20ae4_0.img
285b8c3f-9f10-4e6b-b9bc-e87caaf7d877_0.img
/data/cisco/vm_lifecycle/volumes/285b8c3f-9f10-4e6b-b9bc-e87caaf7d877_0.img
5db7f935-501b-4606-935b-bf650fefdc02_0.img
/data/cisco/vm_lifecycle/volumes/5db7f935-501b-4606-935b-bf650fefdc02_0.img
d4a8df33-3bc1-43db-9a82-b96dc8429fb3_0.img
/data/cisco/vm_lifecycle/volumes/d4a8df33-3bc1-43db-9a82-b96dc8429fb3_0.img
fattest_0.img /data/cisco/vm_lifecycle/volumes/fattest_0.img
TinyLinux.qcow2_0.img /data/cisco/vm_lifecycle/volumes/TinyLinux.qcow2_0.img
vwlc.vmdk_0.img /data/cisco/vm_lifecycle/volumes/vwlc.vmdk_0.img
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
275
Support Commands
support ovs all-info
support ovs all-info
To display the output of all supported ovs commands, use the support ovs all-info command in privileged
EXEC mode.
support ovs all-info
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support ovs all-info
support ovs vsctl show
c23984a8-7379-445d-9ca3-0980bf1db317
Bridge wan-br
Port "vnic4"
Interface "vnic4"
Port wan-br
Interface wan-br
type: internal
Port "vnic2"
Interface "vnic2"
Port "eth0"
Interface "eth0"
Port "vnic9"
Interface "vnic9"
Port "vnic0"
Interface "vnic0"
Bridge int-mgmt-net-br
Port "vnic3"
Interface "vnic3"
Port int-mgmt-net-br
Interface int-mgmt-net-br
type: internal
Bridge lan-br
Port lan-br
Interface lan-br
type: internal
Port "eth6"
Interface "eth6"
Port "eth7"
Interface "eth7"
Port "eth4"
Interface "eth4"
Port "eth2"
Interface "eth2"
Port "eth1"
Interface "eth1"
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
276
Support Commands
support ovs all-info
Port "vnic8"
Interface "vnic8"
Port "eth5"
Interface "eth5"
Port "vnic1"
Interface "vnic1"
Port "eth3"
Interface "eth3"
ovs_version: "2.5.2"
support ovs vsctl list-br
int-mgmt-net-br
lan-br
wan-br
...
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
277
Support Commands
support ovs appctl fdb-show
support ovs appctl fdb-show
To display information about the ports of a bridge , use the support ovs appctl fdb-show command in
privileged EXEC mode.
support ovs appctl fdb-show bridge
Syntax Description bridge Specifies the bridge name.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support ovs appctl fdb-show wan-br
port VLAN MAC Age
1 0 00:24:14:de:0f:b0 275
1 0 00:19:2f:bc:f9:40 271
1 0 b4:14:89:cb:7a:18 252
1 0 a8:9d:21:04:2c:a1 228
1 0 c4:71:fe:60:51:40 211
1 0 00:d0:c9:bd:b1:ca 187
1 0 00:0c:29:25:71:45 176
1 0 0c:4d:e9:c7:14:eb 176
1 0 ac:87:a3:01:5d:38 175
1 0 00:1a:a1:21:a9:08 172
1 0 00:17:08:50:27:9b 153
1 0 00:50:56:87:24:11 150
1 0 00:1a:a1:df:48:70 143
1 0 00:6b:f1:25:13:f0 139
1 0 00:78:88:50:95:40 139
1 0 00:03:ba:85:a1:16 123
1 0 00:11:92:fa:07:d1 123
1 0 50:57:a8:e1:5f:48 122
1 0 70:db:98:c3:fb:00 110
1 0 a8:9d:21:f4:74:10 110
1 0 50:3d:e5:9d:5a:a8 107
1 0 00:17:95:42:67:e0 106
1 0 00:50:56:8b:01:37 105
1 0 a8:9d:21:ce:de:50 81
1 0 fa:9d:46:a0:61:ce 80
1 0 6c:ae:8b:15:f3:c6 61
1 0 4c:4e:35:44:25:ca 59
1 0 80:e0:1d:37:1c:68 54
1 0 00:f2:8b:c3:97:70 52
1 0 a2:6e:e7:10:a1:bb 50
1 0 00:6b:f1:25:13:fc 50
1 0 44:2b:03:16:db:83 50
1 0 80:e0:1d:36:e3:7d 50
1 0 d8:b1:90:40:7a:0f 49
1 0 70:db:98:70:0a:d9 47
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
278
Support Commands
support ovs appctl fdb-show
1 0 a8:9d:21:93:65:06 46
1 0 bc:f1:f2:da:f9:41 40
1 0 5c:f3:fc:2b:2d:79 35
1 0 70:db:98:6f:fb:c0 33
1 0 ce:b2:05:54:47:82 32
1 0 84:b8:02:b8:5a:fc 32
1 0 00:f2:8b:c3:97:7c 32
1 0 10:05:ca:9d:8a:21 31
1 0 d4:6d:50:cf:9e:8d 31
1 0 84:b8:02:5b:cd:d9 29
1 0 00:1e:be:10:81:9a 29
1 0 80:e0:1d:37:2a:80 27
6 0 52:54:00:82:95:43 26
1 0 f8:66:f2:da:0a:80 26
1 0 da:eb:ea:3f:ed:04 25
1 0 50:3d:e5:17:b4:00 23
1 0 e4:c7:22:f0:16:f9 16
1 0 a8:9d:21:ce:de:4b 15
1 0 00:1d:70:7e:5d:80 14
1 0 f8:0b:cb:d6:a6:d5 14
1 0 00:6b:f1:25:13:7c 14
1 0 70:db:98:6f:fb:bb 14
1 0 d4:6d:50:cf:c1:81 13
1 0 80:e0:1d:36:e3:82 13
1 0 a8:9d:21:93:65:02 11
1 0 00:b0:64:fd:06:87 11
1 0 d4:6d:50:cf:c1:86 11
1 0 70:db:98:c3:fa:80 10
1 0 70:db:98:c3:f9:68 10
9 0 52:54:00:85:8a:7a 10
1 0 bc:f1:f2:da:f9:04 9
1 0 00:0c:29:3d:50:1e 7
1 0 00:0c:29:3d:50:0a 7
1 0 52:54:00:54:78:e4 7
1 0 d6:b2:96:90:eb:25 6
1 0 84:b8:02:b8:5a:f7 5
1 0 00:6b:f1:25:13:fd 5
1 0 00:0d:60:84:1e:c0 5
1 0 00:25:45:0e:c3:c0 5
1 0 00:05:73:a0:00:08 2
1 0 00:25:b4:47:44:00 0
1 0 00:09:e6:00:39:d6 0
1 0 68:bc:0c:5b:cb:01 0
1 0 00:00:0c:9f:f0:06 0
LOCAL 0 70:db:98:70:2f:6e 0
1 0 3c:ce:73:da:60:00 0
1 0 00:05:73:a0:00:01 0
1 0 00:00:0c:9f:f0:15 0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
279
Support Commands
support ovs dpctl show
support ovs dpctl show
To display an overview of the database contents, use the support ovs dpctl show command in privileged
EXEC mode.
support ovs dpctl show
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support ovs dpctl show
system@ovs-system:
lookups: hit:9883843 missed:715875 lost:0
flows: 27
masks: hit:38834243 total:4 hit/pkt:3.66
port 0: ovs-system (internal)
port 1: eth4
port 2: eth5
port 3: eth3
port 4: eth1
port 5: eth7
port 6: eth6
port 7: lan-br (internal)
port 8: eth2
port 9: eth0
port 10: wan-br (internal)
port 11: int-mgmt-net-br (internal)
port 12: vnic0
port 13: vnic1
port 14: vnic2
port 15: vnic3
port 16: vnic4
port 17: vnic5
port 18: vnic6
port 19: vnic7
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
280
Support Commands
support ovs ofctl dump-ports
support ovs ofctl dump-ports
To display the port statistics, use the support ovs ofctl dump-ports command in privileged EXEC mode.
support ovs ofctl dump-ports bridge
Syntax Description bridge Specifies the name of the bridge.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support ovs ofctl dump-ports wan-br
OFPST_PORT reply (xid=0x2): 6 ports
port 10: rx pkts=0, bytes=0, drop=0, errs=0, frame=0, over=0, crc=0
tx pkts=513, bytes=80488, drop=5259654, errs=0, coll=0
port 8: rx pkts=0, bytes=0, drop=0, errs=0, frame=0, over=0, crc=0
tx pkts=2280, bytes=365070, drop=6185138, errs=0, coll=0
port 6: rx pkts=2315, bytes=97662, drop=0, errs=0, frame=0, over=0, crc=0
tx pkts=3153581, bytes=501088395, drop=31404, errs=0, coll=0
port 1: rx pkts=14451444, bytes=3479151791, drop=0, errs=0, frame=0, over=0, crc=0
tx pkts=1450836, bytes=167179629, drop=0, errs=0, coll=0
port LOCAL: rx pkts=8318452, bytes=11458196810, drop=6920, errs=0, frame=0, over=0, crc=0
tx pkts=1416016, bytes=164944277, drop=0, errs=0, coll=0
port 9: rx pkts=892, bytes=51312, drop=0, errs=0, frame=0, over=0, crc=0
tx pkts=2940893, bytes=467376770, drop=54234, errs=0, coll=0
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
281
Support Commands
support ovs ofctl dump-ports-desc
support ovs ofctl dump-ports-desc
To display the port descriptions, use the support ovs ofctl dump-ports-desc command in privileged EXEC
mode.
support ovs ofctl dump-ports-desc bridge
Syntax Description bridge Specifies the name of the bridge.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support ovs ofctl dump-ports-desc wan-br
OFPST_PORT_DESC reply (xid=0x2):
1(eth0): addr:70:db:98:70:2f:6e
config: 0
state: 0
current: 1GB-FD COPPER AUTO_NEG
advertised: 10MB-HD 10MB-FD 100MB-HD 100MB-FD 1GB-FD COPPER AUTO_NEG
supported: 10MB-HD 10MB-FD 100MB-HD 100MB-FD 1GB-FD COPPER AUTO_NEG AUTO_PAUSE
speed: 1000 Mbps now, 1000 Mbps max
6(vnic2): addr:fe:54:00:82:95:43
config: 0
state: 0
current: 10MB-FD COPPER
speed: 10 Mbps now, 0 Mbps max
8(vnic1): addr:fe:54:00:3a:f1:c0
config: 0
state: 0
current: 10MB-FD COPPER
speed: 10 Mbps now, 0 Mbps max
9(vnic3): addr:fe:54:00:85:8a:7a
config: 0
state: 0
current: 10MB-FD COPPER
speed: 10 Mbps now, 0 Mbps max
10(vnic6): addr:fe:54:00:e4:a3:3a
config: 0
state: 0
current: 10MB-FD COPPER
speed: 10 Mbps now, 0 Mbps max
LOCAL(wan-br): addr:70:db:98:70:2f:6e
config: 0
state: 0
speed: 0 Mbps now, 0 Mbps max
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
282
Support Commands
support ovs vsctl list-br
support ovs vsctl list-br
To display the names of all bridges, use the support ovs vsctl list-br command in privileged EXEC mode.
support ovs vsctl list-br
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support ovs vsctl list-br
int-mgmt-net-br
lan-br
wan-br
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
283
Support Commands
support ovs vsctl list interface
support ovs vsctl list interface
To display information about a specific interface or all interfaces, use the support ovs vsctl list interface
command in privileged EXEC mode.
support ovs vsctl list interface interface
Syntax Description interface Specifies the interface name.
Command Default Displays information about all interfaces.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support ovs vsctl list interface wan-br
_uuid : be31801b-9729-41c4-8053-52534a59a9c4
admin_state : up
bfd : {}
bfd_status : {}
cfm_fault : []
cfm_fault_status : []
cfm_flap_count : []
cfm_health : []
cfm_mpid : []
cfm_remote_mpids : []
cfm_remote_opstate : []
duplex : []
external_ids : {}
ifindex : 12
ingress_policing_burst: 0
ingress_policing_rate: 0
lacp_current : []
link_resets : 1
link_speed : []
link_state : up
mac : []
mac_in_use : "70:db:98:70:2f:6e"
mtu : 1500
name : wan-br
ofport : 65534
ofport_request : []
options : {}
other_config : {}
statistics : {collisions=0, rx_bytes=11457008582, rx_crc_err=0, rx_dropped=6907,
rx_errors=0, rx_frame_err=0,
rx_over_err=0, rx_packets=8310154, tx_bytes=164896735, tx_dropped=0, tx_errors=0,
tx_packets=1415893}
status : {driver_name=openvswitch}
type : internal
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
284
Support Commands
support ovs vsctl list-ports
support ovs vsctl list-ports
To display the names of all ports on a bridge , use the support ovs vsctl list-ports command in privileged
EXEC mode.
support ovs vsctl list-ports bridge
Syntax Description bridge Specifies the bridge name.
Command Default None.
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support ovs vsctl list-ports wan-br
eth0
vnic1
vnic2
vnic3
vnic6
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
285
Support Commands
support ovs vsctl show
support ovs vsctl show
To display an overview of the database contents, use the support ovs vsctl show command in privileged
EXEC mode.
support ovs vsctl show
Syntax Description This command has no arguments or keywords.
Command Default None
Command Modes Privileged EXEC (#)
Command History Release Modification
3.7.1 This command was introduced.
Example
nfvis# support ovs vsctl show
c9c52c5d-d0f3-4d8d-9ee2-ebd9728b83a6
Bridge wan-br
Port "vnic2"
Interface "vnic2"
Port "vnic3"
Interface "vnic3"
Port wan-br
Interface wan-br
type: internal
Port "eth0"
Interface "eth0"
Port "vnic6"
Interface "vnic6"
Port "vnic1"
Interface "vnic1"
Bridge int-mgmt-net-br
Port "vnic0"
Interface "vnic0"
Port int-mgmt-net-br
Interface int-mgmt-net-br
type: internal
Port "vnic5"
Interface "vnic5"
Bridge lan-br
Port "vnic4"
Interface "vnic4"
Port "eth3"
Interface "eth3"
Port "eth4"
Interface "eth4"
Port lan-br
Interface lan-br
type: internal
Port "eth2"
Interface "eth2"
Port "eth7"
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
286
Support Commands
support ovs vsctl show
Interface "eth7"
Port "eth1"
Interface "eth1"
Port "eth5"
Interface "eth5"
Port "vnic7"
Interface "vnic7"
Port "eth6"
Interface "eth6"
ovs_version: "2.3.2"
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
287
Support Commands
support ovs vsctl show
Cisco Enterprise Network Function Virtualization Infrastructure Software Command Reference
288
You might also like
- Command Reference, Cisco IOS XE 17.15.x (Catalyst 9400 Switches)No ratings yetCommand Reference, Cisco IOS XE 17.15.x (Catalyst 9400 Switches)2,468 pages
- Cisco Nexus 9000 Series NX-OS Command Reference (Show Commands), Release 7.0 (3) I7 (1) (2017-11-15) PDF100% (1)Cisco Nexus 9000 Series NX-OS Command Reference (Show Commands), Release 7.0 (3) I7 (1) (2017-11-15) PDF3,150 pages
- Cisco Mobility Express Command Reference, Release 8.3100% (1)Cisco Mobility Express Command Reference, Release 8.31,158 pages
- Vmware Interview Questions and Answers PDFNo ratings yetVmware Interview Questions and Answers PDF41 pages
- Command Reference, Cisco IOS XE Everest 16.6.x (Catalyst 9400 Switches)No ratings yetCommand Reference, Cisco IOS XE Everest 16.6.x (Catalyst 9400 Switches)932 pages
- HPE FlexFabric 5945 Switch Series Network Management and Monitoring Configuration Guide-Release 655xNo ratings yetHPE FlexFabric 5945 Switch Series Network Management and Monitoring Configuration Guide-Release 655x506 pages
- DGS-3120 Series FW R1.02 CLI Reference Guide PDFNo ratings yetDGS-3120 Series FW R1.02 CLI Reference Guide PDF714 pages
- Mcafee Web Gateway 8.0.x Interface Reference Guide 1-2-2020No ratings yetMcafee Web Gateway 8.0.x Interface Reference Guide 1-2-2020335 pages
- Cisco mds9000 Fundamentals Config Guide 8xNo ratings yetCisco mds9000 Fundamentals Config Guide 8x224 pages
- Checkpoint Real-Exams 156-915 80 v2019-07-21 by Mark 144qNo ratings yetCheckpoint Real-Exams 156-915 80 v2019-07-21 by Mark 144q64 pages
- Cisco NX-OS Cheat Sheet (6.x - 7.x) : Jeff Talamini - Version 1.7No ratings yetCisco NX-OS Cheat Sheet (6.x - 7.x) : Jeff Talamini - Version 1.71 page
- CCNA R&S - Cisco Commands List. Portable Command GuideNo ratings yetCCNA R&S - Cisco Commands List. Portable Command Guide17 pages
- B CLI VMware VM-FEX UCSM Configuration GuideNo ratings yetB CLI VMware VM-FEX UCSM Configuration Guide66 pages
- Easy Virtual Network Configuration Guide, Cisco IOS Release 15M&TNo ratings yetEasy Virtual Network Configuration Guide, Cisco IOS Release 15M&T80 pages
- Cte 114 - Internet and Web TechnologiesNo ratings yetCte 114 - Internet and Web Technologies126 pages
- B Cisco N1KV For KVM Interface Config 5xNo ratings yetB Cisco N1KV For KVM Interface Config 5x26 pages
- Easy Virtual Network Configuration GuideNo ratings yetEasy Virtual Network Configuration Guide80 pages
- B Cisco Nexus 7000 Series NX-OS Fundamentals Configuration Guide Release 6.xNo ratings yetB Cisco Nexus 7000 Series NX-OS Fundamentals Configuration Guide Release 6.x144 pages
- Vsphere 5.5 Command Line Documentation Vsphere Command-Line Interface Documentation Vsphere Command-Line Interface ReferenceNo ratings yetVsphere 5.5 Command Line Documentation Vsphere Command-Line Interface Documentation Vsphere Command-Line Interface Reference23 pages
- Esxcfg-Firewall Esxcfg-Nics Esxcfg-Vswitch Esxcfg-Vswif Esxcfg-Route Esxcfg-VmknicNo ratings yetEsxcfg-Firewall Esxcfg-Nics Esxcfg-Vswitch Esxcfg-Vswif Esxcfg-Route Esxcfg-Vmknic6 pages
- Cisco Unified ICM ACD Supplement For VRU PGNo ratings yetCisco Unified ICM ACD Supplement For VRU PG33 pages
- Check Point Certified Security Expert - R80 (CCSE) : Checkpoint 156-315.80 Dumps Available Here atNo ratings yetCheck Point Certified Security Expert - R80 (CCSE) : Checkpoint 156-315.80 Dumps Available Here at5 pages
- HPE Alletra 9000 - Configuring and Managing Data Replication Using RemoteNo ratings yetHPE Alletra 9000 - Configuring and Managing Data Replication Using Remote92 pages
- Varonis Partner Pack - DatAdvantage Cloud For SalesforceNo ratings yetVaronis Partner Pack - DatAdvantage Cloud For Salesforce6 pages
- (Ebook PDF) A Practical Guide To Advanced Networking 3rd Edition Download100% (1)(Ebook PDF) A Practical Guide To Advanced Networking 3rd Edition Download54 pages
- HP Openview Operations 7.5 For Windows Software: Data SheetNo ratings yetHP Openview Operations 7.5 For Windows Software: Data Sheet8 pages
- Vertiv Intelligent Rack Pdu Instruction ManualNo ratings yetVertiv Intelligent Rack Pdu Instruction Manual79 pages
- DCNG Chapter 3 - Data and Transmission StandardsNo ratings yetDCNG Chapter 3 - Data and Transmission Standards54 pages
- Forcepoint Next Generation Firewall NGFW Administrator Virtual Instructor-Led Training September2020No ratings yetForcepoint Next Generation Firewall NGFW Administrator Virtual Instructor-Led Training September20205 pages
- QIG - 00001 - 05 VEGA Licence Plate Readers Quick Installation GuideNo ratings yetQIG - 00001 - 05 VEGA Licence Plate Readers Quick Installation Guide29 pages
- Apache Log4j Security Bulletin 23 Dec FinalNo ratings yetApache Log4j Security Bulletin 23 Dec Final3 pages
- Set Up A Google Cloud Network Challenge LabNo ratings yetSet Up A Google Cloud Network Challenge Lab7 pages
- VPLEX - No management connectivity to directors on the subnet .253 (MMCS-B) - Dell 中国No ratings yetVPLEX - No management connectivity to directors on the subnet .253 (MMCS-B) - Dell 中国5 pages
- Coe 3204 Computer Networks Question Paper Mid (B) Spring22-23No ratings yetCoe 3204 Computer Networks Question Paper Mid (B) Spring22-233 pages
- Red Hat Enterprise Linux 6 Administration: Real World Skills for Red Hat AdministratorsFrom EverandRed Hat Enterprise Linux 6 Administration: Real World Skills for Red Hat AdministratorsNo ratings yet
- Windows Server 2012 Hyper-V Installation and Configuration GuideFrom EverandWindows Server 2012 Hyper-V Installation and Configuration GuideNo ratings yet
- Linux DevOps Tools Engineer (701) Practice Tests: 400 Questions to Ace Your CertificationFrom EverandLinux DevOps Tools Engineer (701) Practice Tests: 400 Questions to Ace Your CertificationNo ratings yet
- CISCO PACKET TRACER LABS: Best practice of configuring or troubleshooting NetworkFrom EverandCISCO PACKET TRACER LABS: Best practice of configuring or troubleshooting NetworkNo ratings yet
- Network with Practical Labs Configuration: Step by Step configuration of Router and Switch configurationFrom EverandNetwork with Practical Labs Configuration: Step by Step configuration of Router and Switch configurationNo ratings yet
