Scribd Logo
Upload

Welcome to Scribd!

  • 2 views

    T 6DST

    Uploaded by

    msskysarikaya

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    T 6DST

    Uploaded by

    msskysarikaya
    2 views1 page

    Original Title

    T-6DST

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    2 views1 page

    T 6DST

    Uploaded by

    msskysarikaya

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Triumph Daytona 675/675R 2006-2012

    Triumph Street Triple 2008-2012


    Sequential LED Tail Light Installation Guide
    Part# T-6DST-C/S
    Connect Park/Brake
    LED Tail Light

    Blue - Left Signal Left Signal

    Yellow - Right Signal Right Signal


    Sub-Harness

    ! Pre-installation Checklist: Motodynamic Sequential LED Tail Light


    Battery is in heathy and fully charged Programming Instructions
    condition - may need engine on after
    installation to operate signals NOTE: It is recommended that the tail light is programmed
    prior to installation if the button cannot be reached after it is
    If aftermarket front LED signals are installed: mounted to the bike. Simply connect the main harness to
    1. Resistors must be installed on front to slow supply power to the tail light while the key is in the “ON”
    down the flash rate position.
    Signals must be flashing at the stock OEM
    rate prior to install
    ***for Daytona 675/675R, please disable the license plate LED light
    before final installation***

    Park/Brake:

    Locate the main 3 wire harness from


    the bike and connect with the 3 wire
    connector on the LED tail light.
    1. Locate the rubber plug on back housing and remove it
    Wire Color Schematics (if needed):
    Red Wire - Park (+) 2. Turn the key to the “ON” position, making sure the park
    White Wire - Brake (+) lights are on
    Black Wire - Ground (-)
    Sequential Signal: 3. Beneath the rubber plug is a push button, use a pin or
    similar tool to press the button consecutively within 1
    second between each press to program the following:
    Using the supplied sub-harness, connect
    the yellow and blue wire to the matching ON/OFF License plate lights - hit button 2 times
    yellow and blue wire on the LED tail light. ON/OFF Stop Alert - hit button 3 times
    Insulate with green covers. ON/OFF Sequential Signals - hit button 4 times
    Connect the opposite end of the sub-harness The parking light (red) will flash off and on again within 2
    to the bikes factory left and right signal seconds to verify the settings have been saved. The
    connectors. Take note of the different lengths factory settings are defaulted to ON right out of the box
    for all functions.
    Note:
    Two resistors are wired inside the sub-harness. It is 4. Install the rubber plug back into the hole
    normal that these resistors get hot when the turn signals
    are activated. We recommend to mount on metal sub Note: Turning off Stop Alert will enable the brake light to be
    frame away from soft plastics, toolbags, etc to help constant on during brake activation just like stock. Turning
    dissipate the heat. off sequential signals will enable the entire left or right half
    to turn on when the signals are activated.

    *For troubleshoot information please visit:


    http://www.motodynamic.com/faqs

    copyright © MotodynamicTM 2021

    You might also like