75-0001128 - 0 Calculation Landing Platform - KVN Signed

Design Report
OASIS - LANDING PLATFORM
Project-No 75-0001128-01
Client JO CSCODS - TAISEI

KOTA JAKARTA PUSAT
INDONESIA
Document-No 1465_S001_LANDING PLATFORM

0
Date 23-10-24
Pages 24 + Attachment
PERI APAC SERVICES SDN BHD · B-10-02, EAST WING, PJ8 · NO. 23, JALAN BARAT, SEK. 8, · 46050 PETALING JAYA, SELANGOR.
Phone +603-7612 8978
Content
1 Preliminary remarks........................................................................................................................ ..........5

1.1 General............................................................................................................................................
..........5
1.2 Design Class and Partial Safety Factors............................................................................................ ..........5
1.3 Considered safety factors................................................................................................................ ..........5
1.3.1 Partial safety factors for material........................................................................................................ ..........5
1.3.2 Partial safety factors for loads............................................................................................................ ..........5
1.3.3 Partial safety factor for Shoring systems............................................................................................ ..........5
2 Codes and references...................................................................................................................... ..........6

2.1 Design Codes / Standards................................................................................................................ ..........6
2.2 References........................................................................................................................................
..........6
2.3 Softwares............................................................................................................................................
..........6
3 Key Plan............................................................................................................................................
..........7
4 Load assumption............................................................................................................................
.........8
4.1 Permanent actions on shoring (Q1)................................................................................................... ..........8
4.1.1 Self weight formwork (Q1.1)............................................................................................................
..........8
4.2 Variable persistent vertical actions (Q2)........................................................................................... ..........8
4.2.1 Construction operations loading (Q2.3)............................................................................................ ..........8
4.3 Wind Load (Q5)...............................................................................................................................
..........9
4.3.1 Wind on Side Plywood Enclosure (Q5)........................................................................................... ..........9
5 Checks of elements..........................................................................................................................
..........10
5.1 Formwork Girder GT 24....................................................................................................................
..........11
5.2 Hook Strap Uni HBU 24-26................................................................................................................
..........12
5.3 Climbing Rail RCS 3D......................................................................................................................
..........12
5.4 Steel Waler SRU...............................................................................................................................
..........13
5.5 Angle Connector RCS/SRU.............................................................................................................. ..........14
5.5.1 Cross Sections....................................................................................................................................
..........14
5.5.2 Weld Seam........................................................................................................................................
..........14
5.5.3 Bolt Connections................................................................................................................................
..........15
5.6 Heavy Duty Spindles (SLS)................................................................................................................
..........16
5.7 Push Pull Prop RS 210......................................................................................................................
..........16
5.8 Bracing Shoe RCS DW 15................................................................................................................ ..........17
5.9 Baseplate-3 RS 210-1400..........................................................................................................................18
5.10 Anchor Bolt PERI 14/20 x 130 (Bracing Shoe)................................................................................... ..........19
5.11 Anchor Bolt PERI 14/20 x 130 (Baseplate)........................................................................................ ..........19
5.12 Prop PEP 20-400..............................................................................................................................
..........20
5.13 Slipping check of Swivel Coupler SW 48/48 (Class A).................................................................... ..........20
23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 2 | 24

Phone +603-7612 8978
5.14 Pull apart check for Swivel Couplers SW (Class A)............................................................................ ..........21
5.15 Guardrail Post HSGP-2......................................................................................................................
..........21
6 Reaction Forces..............................................................................................................................
..........22
7 Deformation....................................................................................................................................
..........23
8 Conclusion........................................................................................................................................
..........24

Phone +603-7612 8978
Revision
Revision Date Name Remarks

0 23.10.2024 JYT First Issue

Phone +603-7612 8978
1 Preliminary remarks
1.1 General
The following static calculation includes all components of LANDING PLATFORM to the project "OASIS".
Calculations of bearing forces and a detailed structural analysis of the elements are performed.
The responsibility of PERI ends with the loads at the base spindles and anchor points. The transfer of these
loads into the ground or building are not part of this calculation and have to be checked and provided by client.
1.2 Design Class and Partial Safety Factors

Design class according to EN 12812 section 4.3: B1
1.3 Considered safety factors

In this calculation, the following factors are considered:
This applies to all locations where a factor is explicitly stated.
A different factor might be used at some locations for reasons.
At locations where values are taken from documents like approvals, the factors may be different.
1.3.1 Partial safety factors for material

gM1, steel = Partial safety factor for steel = 1.10
gM2, steel = = 1.25
gM1, alu = Partial safety factor for aluminum = 1.10
gM2, alu = = 1.25
gM1, timber = Partial safety factor for timber = 1.30
1.3.2 Partial safety factors for loads

gF, variable = Partial safety factors for variable loads = 1.50
gF, permanent = Partial safety factor for permanent loads = 1.35
1.3.3 Partial safety factor for Shoring systems

gB = Partial safety factor for Shoring according to EN 12812 = 1.00

Phone +603-7612 8978
2 Codes and references

2.1 Design Codes / Standards
The calculations are based on the following design codes / standards:
1. EN 12812 Falsework – Performance requirements and general design

2. EN 1993-1-1 Design of steel structures - General rules and rules for buildings
3. EN 1993-1-3 Design of steel structures - Supplementary rules for cold-formed members and
sheeting
4. EN 1993-1-4 Actions on structures - General Actions - Wind loads
5. EN 1993-1-8 Design of steel structures - Design of joints
6. EN 12811-1 Temporary works equipment - Part 1: Scaffolds - Performance requirements and
general design
2.2 References
The following documents are used to verify the PERI standard components :
1. PERI Design Tables Formwork and Shoring (2015)

2. PERI Product Information (PI) Sheets
2.3 Softwares
The following softwares are used to analyse the PERI standard components :
1. PERICAD Static Tools

2. RSTAB 8 Structure Analysis Software

Phone +603-7612 8978
3 Key Plan
All sketches shown in this section are for illustration purpose only and are not to scale.
Erection of the construction has to be done according to the valid erection and assembly drawings.
The following drawings are associated to the project:

Drawing-No.: 75-0001128-B130

Phone +603-7612 8978
4 Load assumption
4.1 Permanent actions on shoring (Q1)
4.1.1 Self weight formwork (Q1.1)
The self-weight of the formwork is considered with the following value:
q1.1.1 = Timber Planking (40mm thickness) = 0.24 kN/m²
q1.1.2 = Side Plywood Enclosure (H=1.25m) = 10.65 kN/m²
qgt24 = Girder GT24 = 0.06 kN/m

qply,f = Front Plywood Enclosure (H=1.25m) = 0.16 kN/m
*The self weight of the system has been considered in the analysis with factor of 1.2.
4.2 Variable persistent vertical actions (Q2)

4.2.1 Construction operations loading (Q2.3)
The live load on the landing platform has considered self-weight of one slab table with maximum weight, 2
workers and additonal impact load factor of 2. The applied load on the platform assumed to be distributed
evenly.
qtable = Maximum weight of slab table = 15 kN
qworker = 2 number of workers = 1.3kN · 2 = 2.6 kN
cimpact = Impact Load Factor = 2
qtotal = (15.00 + 2.60) . 2.00 = 35.2 kN
W platform = Width of platform 3.32 m

Lplatform = Length of platform 4.35 m
Aplatform = Working area of platform 14.44 m²
q2.3.1 = Operations loading on platform = 35.20 / 14.44 = 2.44 kN/m²

~ 2.50 kN/m²

Phone +603-7612 8978
4.3 Wind Load (Q5)

4.3.1 Wind on Side Plywood Enclosure (Q5)
The following wind from side plywood enclosure results on the landing platform:
cp = = 2.00
qmax,x = Maximum wind pressure = 0.20 kN/m²

Q5,3,max,x = cp qmax,x = 2.00 · 0.20 = 0.40 kN/m²
qwork,x = Wind pressure in working condition = 0.20 kN/m²

Q5,3,work,x = cp qwork,x = 2.00 · 0.20 = 0.40 kN/m²

Phone +603-7612 8978
5 Checks of elements
The following table shows the maximum utilization η of each component:
Item max η
Formwork Girder GT 24 0.35 P
Hook Strap Uni HBU 24-26 0.12 P
Climbing Rail RCS 3D 0.58 P
Steel Waler SRU 0.56 P
Angle Connector RCS/SRU 0.40 P
Heavy Duty Spindles (SLS) 0.87 P
Push Pull Prop RS 210 0.04 P
Bracing Shoe RCS DW 15 0.12 P
Baseplate-3 RS 210-1400 0.03 P
Anchor Bolt PERI 14/20 x 130 (Bracing Shoe) 0.30 P
Anchor Bolt PERI 14/20 x 130 (Baseplate) 0.09 P
Prop PEP 20-400 0.96 P
Slipping check of Swivel Coupler SW 48/48 (Class A) 0.12 P
Pull apart check for Swivel Couplers SW (Class A) 0.03 P
Guardrail Post HSGP-2 0.84 P
The following pages show all the checks and utilizations of each component.

Phone +603-7612 8978
5.1 Formwork Girder GT 24

The GT 24 Formwork Girder provides a high load-bearing capacity and rigidity and can be used for many
applications such as wall wormwork, slab formwork or for induvidual solutions.
Resistances according to PI 320 and the application case.
Case 1 Case 2
Case 3 Case 4
Cross-Section: -
Material: -
Static document: MULTIFLEX - Instructions für Assembly and Use
Art.-No.: 075100 | 075120 | 075150 | 075180 | 075210 | 075240 | 075270 | 075300 | 075330
075360 | 075390 | 075420 | 075450 | 075480 | 075510 | 075540 | 075570 | 075600
Case: 1
Resistances VRd [kN] MRd [kNcm] Fm,Rd [kN] Mm,Rd [kNcm] m: At support
19.50 1050.00 -24.00 1050.00
Forces VEd [kN] MEd [kNcm] Fm,Ed [kN] Mm,Ed [kNcm]

0.28 363.06 -4.88 -9.78
Verification v m f mm
0.01 0.35 0.20 0.01

Phone +603-7612 8978
5.2 Hook Strap Uni HBU 24-26

For assembling the GT 24 Girder on the Steel Walers: U100 – U120.
Cross-Section: -
Material: -
Document: PERI Structural Design Information - RCS/VARIOKIT Connections
Art.-No.: 111806
Loading: Long Term
Resistance NRd [kN]

7.50
Internal Force NEd [kN]

0.90
[Stab 5219, Querschnitt 13, CO105 - RSTAB - 1465_S001_LANDING PLATFORM_F]
Verifiation n
0.12
5.3 Climbing Rail RCS 3D

The climbing rail RCS consists of two U200-Profiles connected together by 2 bolts (in a distance of 50 cm). In
RSTAB the RCS rail is modelled as one member of two single U200-Profiles with lower shear resistance. The
higher stiffness about the z-axis isn't considered and therefore on the safe side.
Cross-Section: 2 x U 200 (EN 1026) (Class 1 acc. to EN 1993-1-1 table 5.2)

Material: S355J2 (EN 10025-2)
Document: -
Art.-No.: 114166 | 109469 | 112102 | 109470 | 112141 | 109471 | 109472 | 109610
Internal Forces NEd [kN] Vy,Ed [kN] Vz,Ed [kN] Mt,Ed [kNcm] My,Ed [kNcm] Mz,Ed [kNcm]
-63.79 -3.49 61.86 73.61 -2161.72 -905.46
[Member 120, Cross-Section 1, CO209 - RSTAB - 1465_S001_LANDING PLATFORM_F]
Resistances Npl,Rd [kN] Vpl,y,Rd [kN] Vpl,z,Rd [kN] Mt,Rd [kNcm] Mpl,y,Rd [kNcm] Mpl,z,Rd [kNcm]
net 1819.56 617.58 432.94 323.72 13270.10 2173.54
Verifications n vy vz mt my mz
0.04 0.01 0.14 0.23 0.16 0.42
Verifications n-m-v
0.58

Phone +603-7612 8978
5.4 Steel Waler SRU

The Steel Waler SRU consists of two U120-sections connected together by stiffener plates and Bolts M20-8.8.
In RSTAB the SRU is modelled as one member of two single U120 cross-sections with lower shear resistance.
The higher stiffness about the z-axis is not considered and therefore on the safe side.
Cross-Section: 2 x U120 (EN 10279) (Class 1 acc. to EN 1993-1-3: 2010-12 table 5.2)
Material: S235J0 (EN 10025-2)
Document: -
Art.-No.: 103868 | 103871 | 103874 | 103877 | 103886 | 103889 | 103898 | 103929 | 103903
103906 | 103915 | 103918 | 103922 | 103925 | 103928 | 103943
Resistances NRd [kN] Vz,Rd [kN] My,Rd [kNcm]

Area A 602.80 113.40 2820.00
Area B 664.00 148.46 2884.00
Internal Forces NEd [kN] Vz,Ed [kN] My,Ed [kNcm]

Area A -26.81 63.27 80.29
Area B -81.58 -9.03 711.43
Verification n v m n-v* v-m* n-v-m*

Area A 0.04 0.56 0.03 0.04 0.03 0.03
Area B 0.12 0.06 0.25 0.12 0.25 0.25
* acc.to DIN EN 1993-1-1

Phone +603-7612 8978
5.5 Angle Connector RCS/SRU

5.5.1 Cross Sections
The connector RCS/SRU consists of a RHS 100x50x6.3 and a U100x80x8 cross-section. The maximum
utilizations are in the net cross-sections, therefore the resistances from the net cross-section will be used.
Cross-Section: RHS 100x50x6.3 (EN 10210) / U100x80x8.0 (EN 10149-2)
Material: S355 J0 & MC (EN 10025-2)
Document: ST_kls_2015_00530
Art.-No.: 111283
Resistances Npl,Rd [kN] Vpl,z,Rd [kN] Mpl,y,Rd [kNcm]

Section 1-1 520.80 196.80 1245.00
Section 3-3 440.30 153.10 1437.00

Section 1-1 -82.03 -10.10 253.68
Section 3-3 -9.07 -0.42 -7.46
Verification n v m n-v-m
Section 1-1 0.19 0.07 0.18 0.37
Section 3-3 0.02 0.00 0.01 0.02
5.5.2 Weld Seam

The resistances of the weld seam are calculated with an equivalent cross-section. The cross-section is equal to
a rectangular hollow section with the dimensions 154x54x4mm as shown below. Resistances and verification
are taken from PERI document ST_kls_2015_00530.
Cross-Section: RHS 154x54x4

Material: S355 (EN 10025-2)
Document: ST_kls_2015_00530
Art.-No.: 111283
Resistances Npl,Rd [kN] Vpl,z,Rd [kN] Mpl,y,Rd [kNcm]

Section 2-2 376.00 376.00 1670.00

Section 2-2 -82.05 -9.12 308.67
Verification n v m n-v-m
Section 2-2 0.22 0.02 0.18 0.40

Phone +603-7612 8978
5.5.3 Bolt Connections

Connection to: U-Profile Section 3-3
Type of Fastener: Fitting Pin Ø 21 mm
Resistances NRd [kN] FRd [kN]

0.00 158.80
Internal Forces NEd [kN] Vz,Ed [kN] FEd [kN]

-44.52 0.00 44.52
Verification hx h
0.00 0.28
Connection to: Rectangular Hollow Section 1-1

Type of Fastener: Fitting Pin Ø 21 mm
Resistances FRd [kN]

105.00
Internal Forces NEd [kN] Vz,Ed [kN] FEd [kN]

10.16 -81.95 82.58
Verification h
0.40

Phone +603-7612 8978
5.6 Heavy Duty Spindles (SLS)

Resistances are according to S-N 190211. The angle with the lowest resistance is considered for every spindle,
always including selfweight and wind force.
Cross-Section: RO 88.9x4.5 | RO 88.9x5.0 (EN 10219)

Material: S235JR | S355J0 (EN 10025-2)
Document: S-N 190211
Art.-No.: 111035 | 101773 | 101774 | 101776 | 101778 | 101779 | 109726 | 109785
Type Cross-Section L [m] FEd [kN] FRd [kN] h

1)
40/ 80* RO 88.9x5.0 0.58 0.00 105.00 0.11
80/140 RO2) 88.9x4.5 0.00 0.00 0.00 0.00
2)
100/180 RO 88.9x4.5 0.00 0.00 0.00 0.00
2)
140/240* RO 88.9x4.5 2.28 91.03 105.00 0.87
1)
200/300 RO 88.9x5.0 0.00 0.00 0.00 0.00
1)
260/360 RO 88.9x5.0 0.00 0.00 0.00 0.00
1)
320/420* RO 88.9x5.0 3.87 68.85 105.00 0.66
1)
380/480 RO 88.9x5.0 0.00 0.00 0.00 0.00
1) 2)
S355J0 S235JR *) in combination with SRU
5.7 Push Pull Prop RS 210

For aligning PERI formwork systems and precast concrete elements.
Cross-Section: RO 60,6 x 2,45 mm (EN 10219)
Material: S250GD+Z()-M-A-C (EN 10346)
Document: RS and RSS Push-Pull Props - Instructions for Assembly and Use
Art.-No.: 117466
Prop: Push Pull Prop RS 210

Extension length: 1.78 m
Resistances F+Rd [kN] F-Rd [kN]

37.50 -37.50
Forces F+RS,Ed [kN] F-RS,Ed [kN]

0.00 -1.36
Verification n+ n-
0.00 0.04

Phone +603-7612 8978
5.8 Bracing Shoe RCS DW 15

For anchoring the bracing with DW 15 to the building slab. Fixation with Anchor System M24 or corresponding
dowels.
Cross-Section: -
Material: -
Document: ST_kls_2015/01031
Art.-No.: 114997
Connection with: 12.00 °

Connected to: Spindle SLS
Seruring elements: 2xM16
Resistances NRd [kN]

102.80
Internal Forces NEd [kN] Reaction forces F1,d [kN] F2,d [kN] CM24 [kN] Fv [kN]
11.96 3.45 -0.96 0.00 5.85
Verification n
0.12
Nd [kN]
150
100
50
0
0 10 20 30 40 50 60 70 80 90  [°]100
-50
-100
-150
5.9 Baseplate-3 RS 210-1400

Phone +603-7612 8978
Push-Pull Props RS are fixed to the Baseplate-3 RS to connect the to the ground or sub-structure.
This load case checks case 1, when two props are mounted and transfer loads in the same direction
(compression or tension forces in both props).
Cross-Section: BL 6 (EN 10029)
Material: S355MC (EN 10204)
Document: RS and RSS Push-Pull Props - Instructions for Assembly and Use
Art.-No.: 126666
Angle 1: 45.00 ° Both forces need to act in the same direction!
Angle 2: 0.00 °

45.75
Forces F1,Ed [kN] F2,Ed [kN]  [°] FEd [kN]

1.29 0.00 45.00 1.29
Reaction forces FV,Ed [kN] FH,Ed [kN]

1.28 0.91
The vertical and horizontal forces derive from the resulting force and are only shown as information.
Verification h
0.03

Phone +603-7612 8978
5.10 Anchor Bolt PERI 14/20 x 130 (Bracing Shoe)

The Anchor bolt is used to fix e.g. Basplates to sub-structures.
All specifications for installation of the bolt needs to be fulfilled.
Cross-Section: -
Material: -
Document: Design Tables Formwork and Shoring
Art.-No.: 124777
Concrete strength:
fck 10.00 N/mm²
fck,cube 12.00 N/mm²
Resistances NRd [kN] VRd [kN]

18.00 52.50
Forces NEd [kN] VEd [kN]

3.45 5.85
Verification n v n-v
0.19 0.11 0.30
5.11 Anchor Bolt PERI 14/20 x 130 (Baseplate)

The Anchor bolt is used to fix e.g. Basplates to sub-structures.
All specifications for installation of the bolt needs to be fulfilled.
Cross-Section: -
Material: -
Document: Design Tables Formwork and Shoring
Art.-No.: 124777
Concrete strength:
fck 10.00 N/mm²
fck,cube 12.00 N/mm²
Resistances NRd [kN] VRd [kN]

18.00 52.50
Forces NEd [kN] VEd [kN]

1.28 0.91
Verification n v n-v
0.07 0.02 0.09

Phone +603-7612 8978
5.12 Prop PEP 20-400

Slap Prop made of steel.
Cross-Section: -
Material: -
Document: PEP Ergo, PEP 10, PEP 20, PEP 30 Instructions for Assembly and Use
Art.-No.: 103060
Prop: PEP 20-400

Extension length: 2.75 m
Base MP 50: No
Orientation: Inner Tube Bottom

54.60
Forces FEd [kN]

52.65
Verification h
0.96
5.13 Slipping check of Swivel Coupler SW 48/48 (Class A)

Coupler resistances are according to EN 74 for forces causing tubes in couplers to slide.
Cross-Section: -
Material: -
Document: EN 74-1
Art.-No.: 0
Coupler: Swivel Coupler SW 48/48 (Class A)

9.09
Forces FEd [kN]

1.07
Verification h
0.12

Phone +603-7612 8978
5.14 Pull apart check for Swivel Couplers SW (Class A)

Coupler resistances are according to EN 74 for forces causing the coupler to break apart.
Cross-Section: -
Material: -
Document: EN 74-1
Art.-No.: 017020 | 017030

12.73
Forces FEd [kN]

0.41
Verification h
0.03
5.15 Guardrail Post HSGP-2

The Guardrail Post HSGP-2 is used as side protection vor various systems and applications.
Cross-Section: RHS35x35x3
Material: S235JRH
Document: ST_was_2010/00902
Art.-No.: 116292
Beam: Full Enclosure
Resistances VRd [kN] MRd [kNcm]

0.70 90.35
Internal Forces VEd [kN] MEd [kNcm]

-0.59 33.33
Verifications v m
0.84 0.37

Phone +603-7612 8978
6 Reaction Forces
The figures below show the reaction forces of the system in Serviceability State Limit result.
Landing Platform (Side View)
RC103 : Authoritative Load Case SLS Against Y-direction

Support Reactions[kN]
Result Combinations: Max and Min Values
36.38
2.37
2.645.42
7.07
0.69
70.72
Max P-X': 5.42, Min P-X': -7.07 kN

Max P-Z': 70.72, Min P-Z': -36.38 kN
Landing Platform (Front View)
RC103 : Authoritative Load Case SLS In X-direction

0.36 0.36
0.40
5.08 5.11
0.43 0.40
5.12 5.04
0.46 0.46
70.72 70.55
Max P-Y': 5.11, Min P-Y': -5.12 kN

Max P-Z': 70.72, Min P-Z': -0.36 kN

Phone +603-7612 8978
7 Deformation
The figure below shows the global deformation of the system in Serviceability Limit State result.
Landing Platform (Side View)
RC103 : Authoritative Load Case SLS Against Y-direction

Global Deformations u-Z [mm]
-1.1
14.6
Max u-Z: 14.6, Min u-Z: -1.1 [mm]

Factor of deformations: 11.00
Landing Platform (Front View)
RC103 : Authoritative Load Case SLS In X-direction

Global Deformations u-Z [mm]
-1.1
14.6
Max u-Z: 14.6, Min u-Z: -1.1 [mm]

Factor of deformations: 11.00

Phone +603-7612 8978
8 Conclusion
The system or systems covered by this calculation are stable and comply with applicable codes and standards.
Subordinate parts and connections are not subject of this calculation. These parts and connections are
designed according to our experience and the state of the art.
The calculation is only valid for PERI products and can not be transferred to products of other manufacturers.
Assembly and usage of materials must be in accordance with the drawings and assembly instructions for this
proof to remain valid.
The customer is responsible for a proper transmission of all reaction forces into the building or soil.
Any alteration of the present system based on this calculation has to be clarified with PERI Engineering.
Issued
PERI APAC SERVICES, 23-10-24
B.Eng Jin Yee Teh Ir. Chin Siang Chua
Phone: +60 3.79128978 Phone: +60 3.79128978

Mail: [email protected] Mail: [email protected]

PERI APAC SERVICES SDN BHD Page: 1/38
Sheet: 1
UNIT B-10-02, EAST WING, PJ8, NO.23, JALAN BARAT, SEKSYEN 8, 46050, PJ, SELANGOR.
Tel: +603-7612 8978
Project: Model: 1465_S001_LANDING PLATFORM_F Date: 24-Oct-24
STRUCTURAL ANALYSIS
PROJECT
75-0001128-01 : OASIS
LANDING PLATFORM
CLIENT
JO CSCODS - TAISEI
KOTA JAKARTA PUSAT
INDONESIA
CREATED BY
PERI APAC SERVICES
Isometric
RSTAB 8.32.01 - Space Frame Structures www.dlubal.com

Sheet: 1
Tel: +603-7612 8978 MODEL
MODEL - GENERAL DATA

General Model name : 1465_S001_LANDING PLATFORM_F
Type of model : 3D
Positive direction of global axis Z : Downward
Classification of load cases and : According to Standard: None
combinations National Annex: None
Options Use CQC Rule
Enable CAD/BIM model
Standard Gravity
g : 10.00 m/s2
1.2 MATERIALS
Matl. Modulus Modulus Spec. Weight Coeff. of Th. Exp. Partial Factor Material
No. E [kN/cm2] G [kN/cm2]  [kN/m3]  [1/°C] M [-] Model
1 PM_S235_B1 | EN 10025-2
21000.00 8076.92 78.50 1.20E-05 1.10 Isotropic Linear
Elastic
User-Defined Material
2 PM_S355_B1 | EN 10025-2
Elastic
3 PM_S700MC_B1 | EN 1993-1-12
Elastic
4 PM_Steel_Dummy | EN 10025-2
Elastic
5 PM_C24_B1 | EN 1995-1-1
Elastic
6 PM_C24_Dummy | EN 1995-1-1
Elastic
7 FinPly 21mm (perpendicular to surface)
Elastic
8 FinPly 18mm (perpendicular to surface)
Elastic
9 PM_DW15_B1 | Z-12.5-96
Elastic
10 PM_S355MC_B1 | EN 10149-2
Elastic
PM_S355MC_B1 | EN 10149-2
11 Steel S 355 J0 | EN 10025-2:2004-11
Elastic
Steel S 355 J0 | EN 10025-2:2004-11
2UR U 200-5/0.1 | - 2UR U 120-5/0.1 | -

1.3 CROSS-SECTIONS
Section Matl. J [cm4] Iy [cm4] Iz [cm4] Principal Axes Rotation Overall Dimensions [mm]
No. No. A [cm2] Ay [cm2] Az [cm2]  [°] ' [°] Width b Height h
1 2UR U 200-5/0.1
2UR U 120-5/0.1 | - RO 88.9x4.5
2 29.57 3820.00 624.93 0.00 0.00 155.0 200.0
64.40 1.06 29.42
CS_RCS_001 | RCS
2 2UR U 120-5/0.1
RO 88.9x5 RO 88.9x5 1 9.88 728.00 202.76 0.00 0.00 115.0 120.0
34.00 0.67 13.91
CS_SRU_001 | SRU_Section A
3 2UR U 120-5/0.1
1 9.88 728.00 202.76 0.00 0.00 115.0 120.0
34.00 0.67 13.91
CS_SRU_002 | SRU_Section B
4 RO 88.9x4.5 | Mannesmann
1 213.09 106.54 106.54 0.00 0.00 88.9 88.9
11.93 5.93 5.93
CS_111035_002 | SLS 40/80_SRU
5 RO 88.9x5 | Mannesmann
1 232.75 116.37 116.37 0.00 0.00 88.9 88.9
13.18 6.55 6.55
IUH 240/80/60/28/8...IUH 200/80/40/27/8...
CS_101776_002 | SLS 140/240_SRU
6 RO 88.9x5 | Mannesmann
2 232.75 116.37 116.37 0.00 0.00 88.9 88.9
13.18 6.55 6.55
CS_109726_002 | SLS 320/420_SRU
7 Fitting pin 21mm_RCS-rail
4 21.33 3820.00 296.00 0.00 0.00 232.0 200.0

Sheet: 1
Tel: +603-7612 8978 MODEL
1.3 CROSS-SECTIONS
64.40 15.65 29.42
SHAPE-THIN 1113...
Connection with fitting pin 21mm to RCS-rail
4 21.33 3820.00 296.00 0.00 0.00 232.0 200.0
64.40 15.65 29.42
SHAPE-THIN 1113... SHAPE-THIN 1156... CS_PROP_PEP
4 21.33 3820.00 296.00 0.00 0.00 232.0 200.0
64.40 15.65 29.42
Connection with fitting pin 26mm to RCS-rail
SHAPE-THIN 1037... T-Rectangle 1000/21 10 Fitting pin 21mm_SRU-waler
4 7.27 728.00 86.40 0.00 0.00 162.0 120.0
34.00 10.24 13.91
Connection with fitting pin 21mm to SRU-waler
11 IUH 240/80/60/28/80/60
T-Rectangle 1000/18RD 15
6 806.37 8467.20 533.95 0.00 0.00 80.0 240.0
129.60 90.19 63.97
CS_GT24_001
12 IUH 200/80/40/27/80/40
RO 48.3x3.2
6 368.68 4570.13 361.02 0.00 0.00 80.0 200.0
96.40 62.74 49.11
VT 20-girder
13 Connection GT24
6 806.37 8467.20 533.95 0.00 0.00 80.0 240.0
RO 60.3x2.3 129.60 90.19 63.97
CS_GT24_002
14 Connection VT20
6 368.68 4570.13 361.02 0.00 0.00 80.0 200.0
96.40 62.74 49.11
QRO 35x35x2 T-Rectangle 40/150
Connection VT 20
15 Connection
4 5.97 777.60 278.30 0.00 0.00 70.0 180.0
28.80 24.00 24.00
2B 105/54/12
Dummy connection stiffness for 2x8mm sheets
17 SHAPE-THIN 111390_CLIMBING RAIL CONNECTOR RCS 97
3 843.83 1541.48 413.57 0.00 0.00 78.0 200.0
38.20 5.17 26.91
111390 Climbing Rail Connector RCS 97
18 SHAPE-THIN 111390_KLETTERSCHIENENVERB RCS 97 _ MITTE
3 854.44 4869.56 667.42 0.00 0.00 78.0 300.0
61.20 4.70 42.23
111390 Climbing Rail Connector RCS 97_center
19 SHAPE-THIN 115623_ECKVERBINDER_SRU_1
2B 100/62/8
2 119.95 155.58 53.26 0.00 0.00 44.0 99.0
17.52 4.15 13.05
115623 Connector SRU VARIOKIT
20 SHAPE-THIN 103737_UK70
2B 354/62/8
2 1.64 666.67 84.47 0.00 0.00 46.0 200.0
20.00 0.04 16.67
103737 Universal Coupling UK 70
21 T-Rectangle 1000/21
7 304.62 77.18 175000.00 0.00 0.00 1000.0 21.0
RRO 180x80x8 210.00 175.00 175.00
Plywood FinPly 21mm
8 192.20 48.60 150000.00 0.00 0.00 1000.0 18.0
180.00 150.00 150.00
2B 100/56/8
Plywood FinPly 18mm
23 RD 15 | DIN 1013-1
9 0.50 0.25 0.25 0.00 0.00 15.0 15.0
1.77 1.49 1.49
Tie rod DW15
25 RO 48.3x3.2 | DIN EN 10220
1 23.17 11.59 11.59 0.00 0.00 48.3 48.3
4.53 2.27 2.27
CS_SCAFFOLD
UU 100/100/8/8/8/... 26 Connection_RO 48.3x3.2 | DIN EN 10220
4 23.17 11.59 11.59 0.00 0.00 48.3 48.3
4.53 2.27 2.27
CS_SCAFFOLD_CON
27 Connection_RO 48.3x3.2 | DIN EN 10220
RHH 100x50x6.3 RHH 100x50x6.3 4 23.17 11.59 11.59 0.00 0.00 48.3 48.3
4.53 2.27 2.27
Half Coupler
28 RO 60.3x2.3 | DIN EN 10220
1 35.30 17.65 17.65 0.00 0.00 60.3 60.3
4.19 2.09 2.09
CS_PUSH_PULL_01
29 QRO 35x35x2 | ALUKÖNIGSTAHL - EN 10305/5 (DIN 2395)
1 7.27 4.71 4.71 0.00 0.00 35.0 35.0
Pipe 75.5/2.6 2.61 1.11 1.11
CS_116292_001
5 266.26 1125.00 80.00 0.00 0.00 40.0 150.0
60.00 50.00 50.00
32 Connection_T-Rectangle 40/150
6 266.26 1125.00 80.00 0.00 0.00 40.0 150.0
60.00 50.00 50.00
34 2B 105/54/12
10 11.23 231.52 277.45 0.00 0.00 78.0 105.0
25.20 21.00 21.00
35 Connection_2B 65/54/12
10 6.62 54.92 171.76 0.00 0.00 78.0 65.0
15.60 13.00 13.00

Sheet: 1
Tel: +603-7612 8978 MODEL
1.3 CROSS-SECTIONS
CS_123509_001 | Welding
4 21.33 3820.00 296.00 0.00 0.00 232.0 200.0
64.40 15.65 29.42
CS_123509_002 | 2x Bolt 21mm | 1x Bolt 21mm
4 21.33 3820.00 296.00 0.00 0.00 232.0 200.0
64.40 15.65 29.42
CS_123509_003 | 2x Bolt 26mm
39 2B 100/62/8
10 3.24 133.33 196.85 0.00 0.00 78.0 100.0
16.00 13.33 13.33
40 2B 354/62/8
10 11.91 5914.92 696.86 0.00 0.00 78.0 354.0
56.64 47.20 47.20
4 21.33 3820.00 296.00 0.00 0.00 232.0 200.0
64.40 15.65 29.42
CS_111382_101
43 RRO 180x80x8 | ALUKÖNIGSTAHL - EN 10210
11 1040.00 1480.00 397.00 0.00 0.00 80.0 180.0
38.40 7.31 25.49
CS_113744_001 | Climbing Rail Hinge RCS 73
4 21.33 3820.00 296.00 0.00 0.00 232.0 200.0
64.40 15.65 29.42
CS_113744_101 | Connection To Hinge RCS 73
46 2B 100/56/8
10 3.24 133.33 164.69 0.00 0.00 72.0 100.0
16.00 13.33 13.33
4 3.24 133.33 164.69 0.00 0.00 72.0 100.0
16.00 13.33 13.33
CS_115298_001
4 3.24 133.33 164.69 0.00 0.00 72.0 100.0
16.00 13.33 13.33
CS_115298_002
4 3.24 133.33 164.69 0.00 0.00 72.0 100.0
16.00 13.33 13.33
CS_115298_003
4 3.24 133.33 164.69 0.00 0.00 72.0 100.0
16.00 13.33 13.33
CS_115298_004
52 UU 100/100/8/8/8/80/0
2 4.42 225.69 215.68 0.00 -90.00 100.0 80.0
21.12 12.59 3.42
CS_111283_001 | Connector RCS/SRU 1
53 RHH 100x50x6.3 | Continental Steel
2 160.00 197.00 63.00 0.00 0.00 50.0 100.0
16.90 3.70 10.90
CS_111283_003 | Connector RCS/SRU
54 RHH 100x50x6.3 | Continental Steel
2 160.00 197.00 63.00 0.00 0.00 50.0 100.0
16.90 3.70 10.90
CS_111283_002 | Connector RCS/SRU Welding
55 Connection_2UR U 120-52/X | DIN 1026-1:1963
4 7.27 728.00 86.40 0.00 0.00 162.0 120.0
34.00 10.24 13.91
CS_111283_102 | Connection to SRU RCS/SRU
56 Connection_2UR U 200-82/X | DIN 1026-1:1963
4 21.33 3820.00 296.00 0.00 0.00 232.0 200.0
64.40 15.65 29.42
CS_111283_101 | Connection To Connector RCS/SRU
58 Pipe 75.5/2.6
1 79.21 39.61 39.61 0.00 0.00 75.5 75.5
5.95 2.97 2.97
1.3.1 CROSS-SECTIONS - CROSS-SECTION ROTATION

Section Angle Mirroring
No. Description [°] About Axis y About Axis z
52 UU 100/100/8/8/8/80/0 -90.00
1.8 NODAL SUPPORTS

Support Rotation [°] Column Support Conditions
No. Nodes No. Sequen. about X about Y about Z in Z uX' uY' uZ' X' Y' Z'
1 32,33,109, XYZ 0.00 0.00 0.00 Friction Ineffective
110 PZ'
LP_Compression
2 31,67,108, XYZ 0.00 0.00 0.00
164
BP_Bracing Shoe
3 28,105 XYZ 0.00 0.00 0.00 Ineffective
Prop_PEP
4 599,600 XYZ 0.00 0.00 0.00
BP_Push Pull

Sheet: 1
Tel: +603-7612 8978 MODEL
1.8.2 NODAL SUPPORTS - SPRINGS

Support Translation Spring [kN/m] Rotation Spring [kNcm/rad]
No. Nodes No. Cu,X' Cu,Y' Cu,Z' C,X' C,Y' C,Z'
3 28,105 - - 45436.400 - - -
1.8.3 NODAL SUPPORTS - INEFFECTIVE

Support Ineffective Support Under
No. Nodes No. PX' PY' PZ' MX' MY' MZ'
1 32,33,109,110 - - Failure if -P - - -
3 28,105 - - Failure if +P - - -
1.8.4 NODAL SUPPORTS - FRICTION

Support Degree of Spring Pressure Forc Friction Coefficient
No. Nodes No. Freedom Cu [kN/m] Direction x y z
1 32,33,109,110 Ux' 0.000 Z 0.100 - -

Sheet: 1
Tel: +603-7612 8978 LOADS
2.1 LOAD CASES

Load Load Case No Standard Self-Weight - Factor in Direction
Case Description Action Category Active X Y Z
LC1 Q1.1_Dead Load Permanent 0.000 0.000 1.200
LC2 Q1.1_Dead Load_2 Permanent
LC6 Q2.3.2_Operation Loading (Working) Imposed
LC11 Q5.1.1_Storm Wind +Y Wind
LC12 Q5.1.2_Storm Wind +X Wind
LC13 Q5.2.1_Working Wind +Y Wind
LC14 Q5.2.2_Working Wind +X Wind
2.1.1 LOAD CASES - CALCULATION PARAMETERS

Load Load Case
Case Description Calculation Parameters
LC1 Q1.1_Dead Load Method of analysis : Geometrically linear analysis
LC2 Q1.1_Dead Load_2 Method of analysis : Geometrically linear analysis
Activate stiffness factors of: : Cross-sections (factor for J, Iy, Iz, A, Ay, Az)
: Members (factor for GJ, EIy, EIz, EA, GA y, GAz)
LC6 Q2.3.2_Operation Loading Method of analysis : Geometrically linear analysis
(Working)
LC11 Q5.1.1_Storm Wind +Y Method of analysis : Geometrically linear analysis
LC12 Q5.1.2_Storm Wind +X Method of analysis : Geometrically linear analysis
LC13 Q5.2.1_Working Wind +Y Method of analysis : Geometrically linear analysis
LC14 Q5.2.2_Working Wind +X Method of analysis : Geometrically linear analysis
2.5 LOAD COMBINATIONS

Load Load Combination
Combin. DS Description No. Factor Load Case
CO101 ULS 1.35G1 + 1.35G2 + 1.5Qi3 + 1.5Qw1 + Imp1 + 1 1.35 LC1 Q1.1_Dead Load
Imp3
2 1.35 LC2 Q1.1_Dead Load_2
3 1.50 LC5 Q2.3.1_Operation Loading (Storm)
4 1.50 LC11 Q5.1.1_Storm Wind +Y
5 1.00 LC21 Imperfection global +Y
6 1.00 LC23 Imperfection local y
Imp4
6 1.00 LC24 Imperfection local z
Imp3
5 1.00 LC22 Imperfection global +Z
Imp4
Imp3
4 1.50 LC12 Q5.1.2_Storm Wind +X
Imp4
Imp3
Imp4
CO109 ULS 1.35G1 + 1.35G2 + 1.5Qi3 - 1.5Qw1 - Imp1 - 1 1.35 LC1 Q1.1_Dead Load
Imp3
4 -1.50 LC11 Q5.1.1_Storm Wind +Y
5 -1.00 LC21 Imperfection global +Y
6 -1.00 LC23 Imperfection local y

Sheet: 1
Tel: +603-7612 8978 LOADS

Imp4
4 -1.50 LC11 Q5.1.1_Storm Wind +Y
6 -1.00 LC24 Imperfection local z
Imp3
4 -1.50 LC11 Q5.1.1_Storm Wind +Y
5 -1.00 LC22 Imperfection global +Z
Imp4
4 -1.50 LC11 Q5.1.1_Storm Wind +Y
Imp3
4 -1.50 LC12 Q5.1.2_Storm Wind +X
Imp4
4 -1.50 LC12 Q5.1.2_Storm Wind +X
Imp3
4 -1.50 LC12 Q5.1.2_Storm Wind +X
Imp4
4 -1.50 LC12 Q5.1.2_Storm Wind +X
CO201 ULS 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 + 1 1.35 LC1 Q1.1_Dead Load
1.5Qi6 + 1.5Qi8 + 1.5Qw3 + Imp1 + Imp3
3 1.50 LC3 Q2.1_Vertical Load
4 1.50 LC4 Q2.2_Storage Areas
5 1.50 LC6 Q2.3.2_Operation Loading (Working)
6 1.50 LC8 Q3.1_Horizontal Load +Y
7 1.50 LC10 Q4.1_In-Situ Concrete Loading
8 1.50 LC13 Q5.2.1_Working Wind +Y
1.5Qi6 + 1.5Qi8 + 1.5Qw3 + Imp1 + Imp4
1.5Qi6 + 1.5Qi8 + 1.5Qw3 + Imp2 + Imp3
1.5Qi6 + 1.5Qi8 + 1.5Qw3 + Imp2 + Imp4
CO205 ULS 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 + 1 1 1.35 LC1 Q1.1_Dead Load

Sheet: 1
Tel: +603-7612 8978 LOADS

1.5Qi7 + 1.5Qi8 + 1.5Qw4 + Imp1 + Imp3
6 1.50 LC9 Q3.2_Horizontal Load +X
8 1.50 LC14 Q5.2.2_Working Wind +X
1.5Qi7 + 1.5Qi8 + 1.5Qw4 + Imp1 + Imp4
1.5Qi7 + 1.5Qi8 + 1.5Qw4 + Imp2 + Imp3
1.5Qi7 + 1.5Qi8 + 1.5Qw4 + Imp2 + Imp4
CO209 ULS 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 - 1 1.35 LC1 Q1.1_Dead Load
1.5Qi6 + 1.5Qi8 - 1.5Qw3 - Imp1 - Imp3
6 -1.50 LC8 Q3.1_Horizontal Load +Y
8 -1.50 LC13 Q5.2.1_Working Wind +Y
1.5Qi6 + 1.5Qi8 - 1.5Qw3 - Imp1 - Imp4
1.5Qi6 + 1.5Qi8 - 1.5Qw3 - Imp2 - Imp3
1.5Qi6 + 1.5Qi8 - 1.5Qw3 - Imp2 - Imp4
1.5Qi7 + 1.5Qi8 - 1.5Qw4 - Imp1 - Imp3
6 -1.50 LC9 Q3.2_Horizontal Load +X

Sheet: 1
Tel: +603-7612 8978 LOADS

8 -1.50 LC14 Q5.2.2_Working Wind +X
1.5Qi7 + 1.5Qi8 - 1.5Qw4 - Imp1 - Imp4
1.5Qi7 + 1.5Qi8 - 1.5Qw4 - Imp2 - Imp3
1.5Qi7 + 1.5Qi8 - 1.5Qw4 - Imp2 - Imp4
CO500 SLS G1 + G2 1 1.00 LC1 Q1.1_Dead Load
CO501 SLS G1 + G2 + Qi3 + Qw1 1 1.00 LC1 Q1.1_Dead Load
CO502 SLS G1 + G2 + Qi3 + Qw2 1 1.00 LC1 Q1.1_Dead Load
CO503 SLS G1 + G2 + Qi3 - Qw1 1 1.00 LC1 Q1.1_Dead Load
4 -1.00 LC11 Q5.1.1_Storm Wind +Y
CO504 SLS G1 + G2 + Qi3 - Qw2 1 1.00 LC1 Q1.1_Dead Load
4 -1.00 LC12 Q5.1.2_Storm Wind +X
CO601 SLS G1 + G2 + Qi1 + Qi2 + Qi4 + Qi6 + Qi8 + Qw3 1 1.00 LC1 Q1.1_Dead Load
CO602 SLS G1 + G2 + Qi1 + Qi2 + Qi4 + Qi7 + Qi8 + Qw4 1 1.00 LC1 Q1.1_Dead Load
CO603 SLS G1 + G2 + Qi1 + Qi2 + Qi4 - Qi6 + Qi8 - Qw3 1 1.00 LC1 Q1.1_Dead Load
CO604 SLS G1 + G2 + Qi1 + Qi2 + Qi4 - Qi7 + Qi8 - Qw4 1 1.00 LC1 Q1.1_Dead Load

Sheet: 1
Tel: +603-7612 8978 LOADS
2.6 RESULT COMBINATIONS

Result
Combin Description Loading
RC1 (ULS) Storm Condition CO101 or to CO116
Load Case 1 ULS
RC2 (ULS) Work Condition CO201 or to CO216
Load Case 2 ULS
RC5 (SLS) Storm Condition CO501 or to CO504
RC6 (SLS) Work Condition CO601 or to CO604
RC101 Authoritative Load Case ULS RC1 or to RC3
Summary of RC1 - RC4
RC103 Authoritative Load Case SLS CO500 or RC5 or to RC7

Sheet: 1
Tel: +603-7612 8978 LOADS
LC2 3.2 MEMBER LOADS LC2: Q1.1_Dead Load_2

Q1.1_Dead Load_2 Reference On Members Load Load Load Reference Load Parameters
No. to No. Type Distribution Direction Length Symbol Value Unit
1 Members Force Uniform Z True Length p 0.060 kN/m
142,143,151-154,162-164,166,169,171,5161-5163,5166-5168,5171-5173,5176-5178,5186-5188,5191-5193,5196-5198,
5201-5203,5206-5208,5211-5213,5216-5218,5221-5223,5226-5228,5242,5302,5303
Girder Weight
2 Members 154,171, Force Uniform Z True Length p 0.160 kN/m
5221-5223
Plywood Weight (Enclosed)
3.5 GENERATED LOADS LC2: Q1.1_Dead Load_2

No. Load Description
1 From Area Loads via Plane
Area load direction Perpendicular to the plane : z
Member load direction Direction of generated member loads: : Local in x, y, z
Area of load application Fully closed plane
Load distribution type: Combined
Area load magnitude Constant : 10.65 kN/m2

Boundary of the area load plane Corner nodes : 145,118,336,317;
342,315,316,348
Note : Each row in the drop
down list box denotes
one plane
Generating total loads in direction P Areas X : 0.000 kN

Y : 0.000 kN
Z : 1.668 kN
P Members X : 0.000 kN
Y : 0.000 kN
Z : 1.668 kN
Total moment to the origin M Areas X : -2.962 kNm

Y : -9.487 kNm
Z : 0.000 kNm
M Members X : -2.962 kNm
Y : -9.451 kNm
Z : 0.000 kNm
Cells selected for generating  number of cells : 26

 cell area : 156599.6 mm2
Convert loads to members No. : 142,143,151-154,5163,

5167,5168,5172,5173,
5178,5188,5193,5197,
5198,5203,5207,5208,
5212,5213,5223,5302,
5303
Comment: Plywood Weight (Enclosed)

Boundary of the area load plane Corner nodes : 317,316,315,145
one plane
Remove influence from Single members : 121,132,136,137,138,

139,140,141,5230,5231,
5232,5233,5282,5283,
5300,5301

Y : 0.000 kN
Z : 4.385 kN
Y : 0.000 kN
Z : 4.385 kN

Y : -24.942 kNm
Z : 0.000 kNm
Y : -24.849 kNm
Z : 0.000 kNm

 cell area : 18269998.8 mm2
Convert loads to members No. : 142,143,151-154,

162-164,166,169,171,
5161-5163,5166-5168,
5171-5173,5176-5178,
5186-5188,5191-5193,
5196-5198,5201-5203,
5206-5208,5211-5213,
5221-5223,5242,5302,5

Sheet: 1
Tel: +603-7612 8978 LOADS
3.5 GENERATED LOADS LC2: Q1.1_Dead Load_2

5303
Comment: Timber Planks (Platform)

Sheet: 1
Tel: +603-7612 8978 LOADS
LC2: Q1.1_DEAD LOAD_2

Against Y-direction
800 mm
M 1:40
10.65
0.24
0.060
0.060
0.160
0.060
0.0600.060 0.060 0.060 0.060 0.060 0.060 0.060 0.060 0.060 0.060
10.65
0.24
LC2 : Q1.1_Dead Load_2
Loads [kN/m], [kN/m^2]

Sheet: 1
Tel: +603-7612 8978 LOADS
LC6 3.5 GENERATED LOADS LC6: Q2.3.2_Operation Loading (Working)

Q2.3.2_Operation Loading
(Working) No. Load Description

one plane

Y : 0.000 kN
Z : 36.105 kN
Y : 0.000 kN
Z : 36.105 kN

Y : -205.377 kNm
Z : 0.000 kNm
Y : -204.607 kNm
Z : 0.000 kNm

 cell area : 14442001.0 mm2
Convert loads to members No. : 5161,5166,5171,5176,

5186,5191,5196,5201,
5206,5211,5221,5242

Sheet: 1
Tel: +603-7612 8978 LOADS
LC6: Q2.3.2_OPERATION LOADING (WORKING)

Against Y-direction
800 mm
M 1:40
2.50
2.50
LC6 : Q2.3.2_Operation Loading (Working)
Loads [kN/m^2]

Sheet: 1
Tel: +603-7612 8978 LOADS
LC11 3.2 MEMBER LOADS LC11: Q5.1.1_Storm Wind +Y

Q5.1.1_Storm Wind +Y Reference On Members Load Load Load Reference Load Parameters
1 Members Force Uniform Y True Length p 0.048 kN/m
6,10-15,28,32,35,46,47,56,60-65,78,81,105-116,118,119,123,126,144,146-149,155,157,207,211,215,219,311,325,360,
361,382,383
SRU
1,9,26,27,30,31,54,59,76,77,80,100,117,120
RCS
3 Members 156,158 Force Uniform Y True Length p 0.021 kN/m
SLS
3.5 GENERATED LOADS LC11: Q5.1.1_Storm Wind +Y


40,19,484,39
one plane

Y : 4.348 kN
Z : 0.000 kN
Y : 4.348 kN
Z : 0.000 kN
Total moment to the origin M Areas X : 2.696 kNm

Y : 0.000 kNm
Z : 24.729 kNm
M Members X : 2.684 kNm
Y : 0.000 kNm
Z : 24.729 kNm

 cell area : 10869999.2 mm2
Convert loads to members No. : 55,66,68-70,82,122,

124,125,134,135,145,
173,174,176,185,186,
188,197,198,200,263,
264,266,269,270,272,
281,282,284,351,353,
355-357,359,387-391,
393

Sheet: 1
Tel: +603-7612 8978 LOADS
LC11: Q5.1.1_STORM WIND +Y

In X-direction
600 mm
M 1:30
0.40
0.40
0.021
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.080
0.021
LC11 : Q5.1.1_Storm Wind +Y
0.40
0.40
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.080

Sheet: 1
Tel: +603-7612 8978 LOADS
LC12 3.2 MEMBER LOADS LC12: Q5.1.2_Storm Wind +X

Q5.1.2_Storm Wind +X Reference On Members Load Load Load Reference Load Parameters
1 Members 154,171, Force Uniform X True Length p 0.080 kN/m
5221-5223
3.5 GENERATED LOADS LC12: Q5.1.2_Storm Wind +X


one plane

Y : 0.000 kN
Z : 0.000 kN
Y : 0.000 kN
Z : 0.000 kN

Y : -1.302 kNm
Z : 3.730 kNm
Y : -1.377 kNm
Z : 3.730 kNm

 cell area : 5249999.8 mm2

5226-5228

Sheet: 1
Tel: +603-7612 8978 LOADS
LC12: Q5.1.2_STORM WIND +X

Against Y-direction
800 mm
M 1:40
0.40
0.40
0.080
LC12 : Q5.1.2_Storm Wind +X

Sheet: 1
Tel: +603-7612 8978 LOADS
LC13 3.2 MEMBER LOADS LC13: Q5.2.1_Working Wind +Y

Q5.2.1_Working Wind +Y Reference On Members Load Load Load Reference Load Parameters
6,10-15,28,32,35,46,47,56,60-65,78,81,105-116,118,119,123,126,144,146-149,155,157,207,211,215,219,311,325,360,
361,382,383
SRU
1,9,26,27,30,31,54,59,76,77,80,100,117,120
RCS
3 Members 156,158 Force Uniform Y True Length p 0.021 kN/m
SLS
3.5 GENERATED LOADS LC13: Q5.2.1_Working Wind +Y


40,19,484,39
one plane

Y : 4.348 kN
Z : 0.000 kN
Y : 4.348 kN
Z : 0.000 kN

Y : 0.000 kNm
Z : 24.729 kNm
Y : 0.000 kNm
Z : 24.729 kNm

 cell area : 10869999.2 mm2
Convert loads to members No. : 55,66,68-70,82,122,

124,125,134,135,145,
173,174,176,185,186,
188,197,198,200,263,
264,266,269,270,272,
281,282,284,351,353,
355-357,359,387-391,
393

Sheet: 1
Tel: +603-7612 8978 LOADS
LC13: Q5.2.1_WORKING WIND +Y

In X-direction
600 mm
M 1:30
0.40
0.40
0.021
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.080
0.021
LC13 : Q5.2.1_Working Wind +Y
0.40
0.40
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.048
0.080

Sheet: 1
Tel: +603-7612 8978 LOADS
LC14 3.2 MEMBER LOADS LC14: Q5.2.2_Working Wind +X

Q5.2.2_Working Wind +X Reference On Members Load Load Load Reference Load Parameters
1 Members 154,171, Force Uniform X True Length p 0.080 kN/m
5221-5223
3.5 GENERATED LOADS LC14: Q5.2.2_Working Wind +X


one plane

Y : 0.000 kN
Z : 0.000 kN
Y : 0.000 kN
Z : 0.000 kN

Y : -1.302 kNm
Z : 3.730 kNm
Y : -1.377 kNm
Z : 3.730 kNm

 cell area : 5249999.8 mm2

5226-5228

Sheet: 1
Tel: +603-7612 8978 LOADS
LC14: Q5.2.2_WORKING WIND +X

Against Y-direction
800 mm
M 1:40
0.40
0.40
0.080
LC14 : Q5.2.2_Working Wind +X

Sheet: 1
Tel: +603-7612 8978 RESULTS
4.3 CROSS-SECTIONS - INTERNAL FORCES Result Combinations

Member Node Location Forces [kN] Moments [kNm] Correspondin
No. RC No. x [mm] N Vy Vz MT My Mz Load Cases
Section No. 1: 2UR U 200-5/0.1 | - (CS_RCS_001 | RCS)
77 RC101 0.0 MAX N 11.75 0.01 -53.12 0.00 -2.79 0.00 CO 205
309 RC101 0.0 MIN N -65.84 -1.51 -2.72 0.01 5.34 -2.17 CO 209
100 RC101 325.0 MAX Vy -62.97 4.73 -1.20 -0.02 -12.56 -2.54 CO 209
54 RC101 325.0 MIN Vy -62.63 -4.74 -1.25 0.02 -12.54 2.55 CO 201
120 RC101 0.0 MAX Vz -63.79 -3.49 61.86 0.74 -21.62 -9.05 CO 209
77 RC101 250.0 MIN Vz 9.59 4.02 -55.57 -0.06 -16.20 -1.01 CO 209
80 RC101 0.0 MAX MT -26.03 -3.54 6.19 1.18 -5.27 -7.75 CO 109
80 RC101 0.0 MIN MT -19.25 3.43 5.07 -1.18 -4.15 7.67 CO 101
39 RC101 1375.0 MAX My -64.03 0.02 3.05 0.00 5.61 0.00 CO 213
117 RC101 0.0 MIN My -63.46 3.47 61.72 -0.73 -21.63 9.08 CO 201
117 RC101 0.0 MAX Mz -63.46 3.47 61.72 -0.73 -21.63 9.08 CO 201
120 RC101 0.0 MIN Mz -63.79 -3.49 61.86 0.74 -21.62 -9.05 CO 209
Section No. 2: 2UR U 120-5/0.1 | - (CS_SRU_001 | SRU_Section A)
219 RC101 0.0 MAX N 0.88 -0.79 -6.63 -0.03 -1.07 0.04 CO 201
157 RC101 220.0 MIN N -82.41 1.62 -8.87 0.10 8.43 0.41 CO 209
15 RC101 125.0 MAX Vy -26.76 4.47 62.93 0.06 8.67 -0.63 CO 201
65 RC101 125.0 MIN Vy -26.89 -4.49 63.25 -0.06 8.71 0.63 CO 209
65 RC101 0.0 MAX Vz -26.81 -4.35 63.27 -0.13 0.80 0.07 CO 209
63 RC101 250.0 MIN Vz -81.83 0.57 -9.19 0.14 1.41 -0.09 CO 209
47 RC101 0.0 MAX MT -81.52 0.66 -8.96 0.20 8.51 0.46 CO 209
46 RC101 0.0 MIN MT -81.12 -0.65 -8.93 -0.20 8.46 -0.46 CO 201
157 RC101 0.0 MAX My -82.32 1.61 -8.75 0.12 10.37 0.77 CO 209
219 RC101 125.0 MIN My -0.13 1.03 -7.57 0.04 -2.28 -0.22 CO 209
157 RC101 0.0 MAX Mz -82.32 1.61 -8.75 0.12 10.37 0.77 CO 209
155 RC101 0.0 MIN Mz -81.92 -1.60 -8.72 -0.12 10.31 -0.77 CO 201
Section No. 3: 2UR U 120-5/0.1 | - (CS_SRU_002 | SRU_Section B)
10 RC101 150.0 MAX N 2.78 0.89 6.80 0.05 -0.54 0.16 CO 201
64 RC101 375.0 MIN N -81.73 0.60 -9.15 0.16 3.70 0.07 CO 209
126 RC101 62.5 MAX Vy -0.13 1.02 -7.51 0.03 -1.34 -0.10 CO 209
123 RC101 62.5 MIN Vy 0.64 -1.15 -7.39 -0.02 -1.21 0.11 CO 201
60 RC101 0.0 MAX Vz 1.99 -0.84 6.92 -0.02 -1.63 -0.27 CO 209
64 RC101 375.0 MIN Vz -81.73 0.60 -9.15 0.16 3.70 0.07 CO 209
64 RC101 0.0 MAX MT -81.58 0.64 -9.03 0.18 7.11 0.34 CO 209
14 RC101 0.0 MIN MT -81.18 -0.64 -9.00 -0.18 7.07 -0.34 CO 201
64 RC101 0.0 MAX My -81.58 0.64 -9.03 0.18 7.11 0.34 CO 209
60 RC101 0.0 MIN My 1.99 -0.84 6.92 -0.02 -1.63 -0.27 CO 209
64 RC101 0.0 MAX Mz -81.58 0.64 -9.03 0.18 7.11 0.34 CO 209
14 RC101 0.0 MIN Mz -81.18 -0.64 -9.00 -0.18 7.07 -0.34 CO 201
Section No. 4: RO 88.9x4.5 | Mannesmann (CS_111035_002 | SLS 40/80_SRU)
91 RC101 0.0 MAX N 11.96 0.00 0.04 0.00 0.00 0.00 CO 205
45 RC101 0.0 MIN N 0.00 0.00 0.00 0.00 0.00 0.00
45 RC101 0.0 MAX Vy 0.00 0.00 0.00 0.00 0.00 0.00
45 RC101 0.0 MIN Vy 0.00 0.00 0.00 0.00 0.00 0.00
45 RC101 0.0 MAX Vz 1.92 0.00 0.04 0.00 0.00 0.00 CO 113
45 RC101 580.3 MIN Vz 1.90 0.00 -0.04 0.00 0.00 0.00 CO 113
45 RC101 0.0 MAX MT 0.00 0.00 0.00 0.00 0.00 0.00
45 RC101 0.0 MIN MT 0.00 0.00 0.00 0.00 0.00 0.00
45 RC101 290.1 MAX My 1.91 0.00 0.00 0.00 0.01 0.00 CO 113
45 RC101 0.0 MIN My 0.00 0.00 0.00 0.00 0.00 0.00
45 RC101 0.0 MAX Mz 0.00 0.00 0.00 0.00 0.00 0.00
45 RC101 0.0 MIN Mz 0.00 0.00 0.00 0.00 0.00 0.00
Section No. 5: RO 88.9x5 | Mannesmann (CS_101776_002 | SLS 140/240_SRU)
158 RC101 0.0 MAX N 91.03 0.03 0.13 0.00 0.00 0.00 CO 209
156 RC101 0.0 MIN N 0.00 0.00 0.00 0.00 0.00 0.00
156 RC101 0.0 MAX Vy 28.29 0.03 0.14 0.00 0.00 0.00 CO 109
156 RC101 2275.0 MIN Vy 28.06 -0.03 -0.14 0.00 0.00 0.00 CO 109
156 RC101 0.0 MAX Vz 28.29 0.03 0.14 0.00 0.00 0.00 CO 109
156 RC101 2275.0 MIN Vz 28.06 -0.03 -0.14 0.00 0.00 0.00 CO 109
156 RC101 1137.5 MAX MT 90.47 0.00 0.00 0.00 0.07 0.02 CO 201
158 RC101 1137.5 MIN MT 90.91 0.00 0.00 0.00 0.07 -0.02 CO 209
156 RC101 1137.5 MAX My 28.17 0.00 0.00 0.00 0.08 -0.02 CO 109
156 RC101 0.0 MIN My 0.00 0.00 0.00 0.00 0.00 0.00
158 RC101 1137.5 MAX Mz 28.57 0.00 0.00 0.00 0.08 0.02 CO 101
156 RC101 1137.5 MIN Mz 28.17 0.00 0.00 0.00 0.08 -0.02 CO 109
Section No. 6: RO 88.9x5 | Mannesmann (CS_109726_002 | SLS 320/420_SRU)
67 RC101 0.0 MAX N 68.85 0.00 0.22 0.00 0.00 0.00 CO 209
17 RC101 0.0 MIN N 0.00 0.00 0.00 0.00 0.00 0.00
67 RC101 3865.4 MAX Vy 62.91 0.00 -0.22 0.00 0.00 0.00 CO 201
67 RC101 0.0 MIN Vy 63.16 0.00 0.22 0.00 0.00 0.00 CO 201
17 RC101 0.0 MAX Vz 21.51 0.00 0.27 0.00 0.00 0.00 CO 109
17 RC101 3865.4 MIN Vz 21.26 0.00 -0.27 0.00 0.00 0.00 CO 109
67 RC101 1932.7 MAX MT 21.69 0.00 0.00 0.00 0.25 0.00 CO 101
17 RC101 1932.7 MIN MT 21.39 0.00 0.00 0.00 0.25 0.00 CO 109
17 RC101 1932.7 MAX My 21.39 0.00 0.00 0.00 0.25 0.00 CO 109
17 RC101 0.0 MIN My 0.00 0.00 0.00 0.00 0.00 0.00
17 RC101 0.0 MAX Mz 0.00 0.00 0.00 0.00 0.00 0.00
17 RC101 0.0 MIN Mz 0.00 0.00 0.00 0.00 0.00 0.00
Section No. 7: Fitting pin 21mm_RCS-rail (Connection with fitting pin 21mm to RCS-rail)
99 RC101 0.0 MAX N 54.62 0.65 72.53 0.00 0.00 0.00 CO 209
71 RC101 55.0 MIN N -2.50 0.00 -11.69 0.00 -0.64 0.00 CO 205
88 RC101 55.0 MAX Vy 26.36 1.94 -63.29 0.19 -3.48 -0.11 CO 209
42 RC101 55.0 MIN Vy 26.23 -1.93 -62.97 -0.19 -3.46 0.11 CO 201
99 RC101 55.0 MAX Vz 54.62 0.65 72.53 0.00 3.99 -0.04 CO 209
88 RC101 55.0 MIN Vz 26.36 1.94 -63.29 0.19 -3.48 -0.11 CO 209
88 RC101 55.0 MAX MT 26.36 1.94 -63.29 0.19 -3.48 -0.11 CO 209
42 RC101 55.0 MIN MT 26.23 -1.93 -62.97 -0.19 -3.46 0.11 CO 201
99 RC101 55.0 MAX My 54.62 0.65 72.53 0.00 3.99 -0.04 CO 209

Sheet: 1
Tel: +603-7612 8978 RESULTS

88 RC101 55.0 MIN My 26.36 1.94 -63.29 0.19 -3.48 -0.11 CO 209
42 RC101 55.0 MAX Mz 26.23 -1.93 -62.97 -0.19 -3.46 0.11 CO 201
88 RC101 55.0 MIN Mz 26.36 1.94 -63.29 0.19 -3.48 -0.11 CO 209
Section No. 8: Fitting pin 21mm_RCS-rail (CS_PROP_PEP)
22 RC101 0.0 MAX N 0.00 0.00 0.00 0.00 0.00 0.00
72 RC101 109.8 MIN N -52.65 0.00 -0.05 0.00 -0.01 0.00 CO 209
22 RC101 0.0 MAX Vy -52.43 0.00 -0.05 0.00 0.00 0.00 CO 201
72 RC101 0.0 MIN Vy -52.65 0.00 -0.05 0.00 0.00 0.00 CO 209
22 RC101 0.0 MAX Vz 0.00 0.00 0.00 0.00 0.00 0.00
72 RC101 0.0 MIN Vz -52.65 0.00 -0.05 0.00 0.00 0.00 CO 209
22 RC101 0.0 MAX MT 0.00 0.00 0.00 0.00 0.00 0.00
22 RC101 0.0 MIN MT 0.00 0.00 0.00 0.00 0.00 0.00
22 RC101 0.0 MAX My 0.00 0.00 0.00 0.00 0.00 0.00
72 RC101 122.0 MIN My -52.65 0.00 -0.05 0.00 -0.01 0.00 CO 209
72 RC101 122.0 MAX Mz -52.65 0.00 -0.05 0.00 -0.01 0.00 CO 209
22 RC101 122.0 MIN Mz -52.43 0.00 -0.05 0.00 -0.01 0.00 CO 201
Section No. 9: Fitting pin 26mm_RCS-rail (Connection with fitting pin 26mm to RCS-rail)
74 RC101 120.0 MAX N 0.00 -3.95 0.01 0.00 0.00 0.02 CO 201
75 RC101 120.0 MIN N -101.66 -7.19 -9.87 0.00 -1.19 0.64 CO 209
25 RC101 0.0 MAX Vy -40.89 7.64 -4.01 0.00 0.00 -0.15 CO 101
75 RC101 0.0 MIN Vy -41.11 -7.66 -4.03 0.00 0.00 0.16 CO 109
24 RC101 120.0 MAX Vz 0.00 -3.94 0.01 0.00 0.00 0.02 CO 201
75 RC101 0.0 MIN Vz -101.66 -7.20 -9.87 0.00 0.00 -0.22 CO 209
75 RC101 120.0 MAX MT -101.66 -7.19 -9.87 0.00 -1.19 0.64 CO 209
25 RC101 120.0 MIN MT -101.44 7.19 -9.84 0.00 -1.18 -0.64 CO 201
75 RC101 0.0 MAX My -33.49 7.57 -3.29 0.00 0.00 -0.17 CO 101
75 RC101 120.0 MIN My -101.66 -7.19 -9.87 0.00 -1.19 0.64 CO 209
75 RC101 120.0 MAX M z -41.12 -7.65 -4.03 0.00 -0.48 1.08 CO 109
75 RC101 120.0 MIN Mz -33.49 7.57 -3.29 0.00 -0.39 -1.08 CO 101
Section No. 10: Fitting pin 21mm_SRU-waler (Connection with fitting pin 21mm to SRU-waler)
57 RC101 0.0 MAX N 63.24 4.34 -26.86 0.00 0.00 0.00 CO 209
58 RC101 30.0 MIN N -71.98 -6.09 -55.38 0.14 -1.66 0.18 CO 209
8 RC101 0.0 MAX Vy -71.63 6.07 -55.11 0.00 0.00 0.00 CO 201
58 RC101 0.0 MIN Vy -71.98 -6.10 -55.38 0.00 0.00 0.00 CO 209
5181 RC101 30.0 MAX Vz 11.34 1.62 2.00 0.00 0.06 -0.05 CO 201
58 RC101 0.0 MIN Vz -71.98 -6.10 -55.38 0.00 0.00 0.00 CO 209
58 RC101 30.0 MAX MT -71.98 -6.09 -55.38 0.14 -1.66 0.18 CO 209
8 RC101 30.0 MIN MT -71.63 6.07 -55.11 -0.14 -1.65 -0.18 CO 201
5118 RC101 60.0 MAX My 0.27 -0.30 0.76 0.04 0.10 0.01 CO 109
58 RC101 30.0 MIN My -71.98 -6.09 -55.38 0.14 -1.66 0.18 CO 209
58 RC101 30.0 MAX Mz -71.98 -6.09 -55.38 0.14 -1.66 0.18 CO 209
8 RC101 30.0 MIN Mz -71.63 6.07 -55.11 -0.14 -1.65 -0.18 CO 201
Section No. 11: IUH 240/80/60/28/80/60 (CS_GT24_001)
162 RC101 0.0 MAX N 0.59 0.01 -0.31 0.00 -0.48 0.00 CO 109
162 RC101 185.5 MIN N -0.59 0.00 -0.38 0.00 0.36 0.00 CO 201
5221 RC101 3552.0 MAX Vy -0.15 0.29 -4.06 0.00 -0.17 -0.01 CO 205
5221 RC101 0.0 MIN Vy -0.15 -0.29 4.06 0.00 -0.17 -0.01 CO 205
5221 RC101 0.0 MAX Vz -0.12 -0.03 4.34 0.00 -0.66 0.00 CO 209
5221 RC101 3552.0 MIN Vz -0.18 0.03 -4.34 0.00 -0.67 0.00 CO 201
171 RC101 0.0 MAX MT 0.04 -0.04 -0.46 0.03 -0.06 0.00 CO 213
5222 RC101 185.5 MIN MT 0.04 0.05 0.46 -0.03 -0.06 0.00 CO 213
5221 RC101 1776.0 MAX My -0.15 0.00 0.28 0.00 3.63 0.02 CO 209
5221 RC101 3552.0 MIN My -0.18 0.03 -4.34 0.00 -0.67 0.00 CO 201
5221 RC101 1776.0 MAX Mz -0.18 0.00 0.00 0.00 3.62 0.25 CO 205
5221 RC101 1776.0 MIN Mz -0.16 0.00 0.00 0.00 3.62 -0.21 CO 213
Section No. 13: Connection GT24 (CS_GT24_002)
5220 RC101 108.0 MAX N 0.90 -0.04 0.15 0.00 0.02 0.00 CO 205
5224 RC101 0.0 MIN N -4.88 -0.77 0.03 0.00 0.00 -0.10 CO 201
5225 RC101 120.0 MAX Vy -4.88 0.71 0.02 0.00 0.00 0.00 CO 209
5224 RC101 120.0 MIN Vy -4.88 -0.77 0.03 0.00 0.00 -0.01 CO 201
5225 RC101 72.0 MAX Vz -4.59 0.17 0.35 0.00 0.00 0.01 CO 205
5224 RC101 84.0 MIN Vz -4.61 -0.17 -0.31 0.00 0.00 -0.01 CO 213
5225 RC101 0.0 MAX MT -4.59 0.17 0.35 0.00 -0.03 0.02 CO 205
5224 RC101 0.0 MIN MT -4.88 -0.77 0.03 0.00 0.00 -0.10 CO 201
5224 RC101 0.0 MAX My -4.61 -0.17 -0.31 0.00 0.03 -0.02 CO 213
5225 RC101 0.0 MIN My -4.59 0.17 0.35 0.00 -0.03 0.02 CO 205
5225 RC101 0.0 MAX Mz -4.88 0.71 0.02 0.00 0.00 0.09 CO 209
5224 RC101 0.0 MIN Mz -4.88 -0.77 0.03 0.00 0.00 -0.10 CO 201
Section No. 15: Connection (Dummy connection stiffness for 2x8mm sheets)
97 RC101 0.0 MAX N 3.83 0.00 -3.43 0.00 0.02 0.00 CO 205
98 RC101 48.0 MIN N -7.86 0.00 -1.00 0.00 -0.04 0.00 CO 205
50 RC101 49.0 MAX Vy 2.10 0.02 10.13 0.00 0.50 0.00 CO 209
96 RC101 49.0 MIN Vy 2.11 -0.03 10.14 0.00 0.50 0.00 CO 201
96 RC101 49.0 MAX Vz 2.43 0.00 11.69 0.00 0.57 0.00 CO 205
97 RC101 170.0 MIN Vz 3.83 0.00 -3.43 0.00 -0.56 0.00 CO 205
52 RC101 0.0 MAX MT -6.81 0.02 -0.87 0.00 0.01 0.00 CO 209
98 RC101 0.0 MIN MT -6.82 -0.02 -0.87 0.00 0.01 0.00 CO 201
96 RC101 49.0 MAX My 2.43 0.00 11.69 0.00 0.57 0.00 CO 205
97 RC101 170.0 MIN My 3.83 0.00 -3.43 0.00 -0.56 0.00 CO 205
96 RC101 49.0 MAX Mz 2.11 -0.03 10.14 0.00 0.50 0.00 CO 201
50 RC101 49.0 MIN Mz 2.10 0.02 10.13 0.00 0.50 0.00 CO 209
Section No. 25: RO 48.3x3.2 | DIN EN 10220 (CS_SCAFFOLD)
131 RC101 0.0 MAX N 1.07 0.00 0.13 0.00 0.00 0.00 CO 109
131 RC101 2378.9 MIN N -1.02 0.00 0.00 0.00 0.18 0.00 CO 101
129 RC101 150.0 MAX Vy 0.33 0.65 0.43 -0.03 0.07 -0.10 CO 109
129 RC101 150.0 MIN Vy -0.13 -0.67 0.40 0.03 0.06 0.10 CO 101
129 RC101 0.0 MAX Vz 0.33 0.65 0.44 -0.03 0.00 0.00 CO 109

Sheet: 1
Tel: +603-7612 8978 RESULTS

40 RC101 150.7 MIN Vz 0.45 0.60 -0.52 -0.01 -0.01 0.01 CO 109
5158 RC101 0.0 MAX MT -0.27 0.00 0.09 0.04 0.00 0.00 CO 109
5158 RC101 0.0 MIN MT 0.36 -0.01 0.12 -0.04 0.00 0.00 CO 101
131 RC101 2378.9 MAX My -1.02 0.00 0.00 0.00 0.18 0.00 CO 101
41 RC101 3290.0 MIN My 0.53 0.00 -0.12 -0.02 -0.02 0.00 CO 201
5158 RC101 3289.3 MAX Mz -0.27 -0.07 -0.08 0.04 0.01 0.12 CO 109
41 RC101 0.0 MIN Mz -0.39 -0.06 0.09 0.03 0.02 -0.11 CO 109
Section No. 26: Connection_RO 48.3x3.2 | DIN EN 10220 (CS_SCAFFOLD_CON)
133 RC101 0.0 MAX N 0.41 -0.66 0.68 0.00 0.00 0.00 CO 101
130 RC101 0.0 MIN N 0.00 0.00 0.00 0.00 0.00 0.00
133 RC101 72.2 MAX Vy 0.41 0.72 -0.68 0.02 -0.05 -0.05 CO 109
130 RC101 72.2 MIN Vy 0.34 -0.73 0.72 0.01 0.05 0.05 CO 109
130 RC101 72.2 MAX Vz 0.34 -0.73 0.72 0.01 0.05 0.05 CO 109
130 RC101 72.2 MIN Vz 0.34 0.65 -0.72 0.01 -0.05 -0.05 CO 101
133 RC101 72.2 MAX MT 0.41 0.72 -0.68 0.02 -0.05 -0.05 CO 109
130 RC101 0.0 MIN MT 0.00 0.00 0.00 0.00 0.00 0.00
130 RC101 72.2 MAX My 0.34 -0.73 0.72 0.01 0.05 0.05 CO 109
130 RC101 72.2 MIN My 0.34 0.65 -0.72 0.01 -0.05 -0.05 CO 101
130 RC101 72.2 MAX Mz 0.34 -0.73 0.72 0.01 0.05 0.05 CO 109
133 RC101 72.2 MIN Mz 0.41 0.72 -0.68 0.02 -0.05 -0.05 CO 109
Section No. 27: Connection_RO 48.3x3.2 | DIN EN 10220 (Half Coupler)
44 RC101 0.0 MAX N 0.50 0.45 -0.61 -0.01 -0.01 0.01 CO 109
44 RC101 0.0 MIN N 0.00 0.00 0.00 0.00 0.00 0.00
101 RC101 0.0 MAX Vy 0.12 0.53 0.00 0.00 -0.02 0.02 CO 201
101 RC101 0.0 MIN Vy 0.09 -0.39 0.01 0.00 0.03 -0.01 CO 109
150 RC101 36.2 MAX Vz 0.27 -0.30 0.76 0.00 0.05 0.01 CO 109
150 RC101 36.2 MIN Vz 0.22 0.14 -0.75 0.00 -0.05 -0.01 CO 101
90 RC101 36.2 MAX M T 0.07 0.28 -0.04 0.00 -0.04 -0.01 CO 109
44 RC101 0.0 MIN MT 0.50 0.45 -0.61 -0.01 -0.01 0.01 CO 109
150 RC101 36.2 MAX My 0.27 -0.30 0.76 0.00 0.05 0.01 CO 109
150 RC101 36.2 MIN My 0.22 0.14 -0.75 0.00 -0.05 -0.01 CO 101
101 RC101 0.0 MAX Mz 0.12 0.53 0.00 0.00 -0.02 0.02 CO 201
101 RC101 0.0 MIN Mz 0.09 -0.39 0.01 0.00 0.03 -0.01 CO 109
Section No. 28: RO 60.3x2.3 | DIN EN 10220 (CS_PUSH_PULL_01)
5352 RC101 0.0 MAX N 1.29 0.00 0.03 0.00 0.00 0.00 CO 201
5351 RC101 1774.8 MIN N -1.36 0.00 -0.03 0.00 0.00 0.00 CO 201
5352 RC101 0.0 MAX Vy 1.29 0.00 0.03 0.00 0.00 0.00 CO 201
5352 RC101 1774.8 MIN Vy 1.22 0.00 -0.03 0.00 0.00 0.00 CO 201
5352 RC101 0.0 MAX Vz -1.30 0.00 0.03 0.00 0.00 0.00 CO 209
5352 RC101 1774.8 MIN Vz -1.36 0.00 -0.03 0.00 0.00 0.00 CO 209
5351 RC101 0.0 MAX MT 0.00 0.00 0.00 0.00 0.00 0.00
5351 RC101 0.0 MIN MT 0.00 0.00 0.00 0.00 0.00 0.00
5352 RC101 887.4 MAX My -1.33 0.00 0.00 0.00 0.02 0.00 CO 209
5351 RC101 0.0 MIN My 0.00 0.00 0.00 0.00 0.00 0.00
5351 RC101 0.0 MAX Mz 0.00 0.00 0.00 0.00 0.00 0.00
5351 RC101 0.0 MIN Mz 0.00 0.00 0.00 0.00 0.00 0.00
Section No. 29: QRO 35x35x2 | ALUKÖNIGSTAHL - EN 10305/5 (DIN 2395) (CS_116292_001)
167 RC101 0.0 MAX N 0.00 0.00 0.00 0.00 0.00 0.00
5308 RC101 235.0 MIN N -0.26 -0.04 -0.03 0.00 0.03 0.04 CO 213
5248 RC101 0.0 MAX Vy -0.18 0.59 0.01 0.00 0.00 -0.33 CO 109
5244 RC101 0.0 MIN Vy -0.19 -0.59 0.01 0.00 0.00 0.33 CO 101
366 RC101 0.0 MAX Vz -0.16 -0.01 0.06 0.00 0.00 0.02 CO 213
374 RC101 0.0 MIN Vz -0.11 0.01 -0.05 0.00 0.00 -0.01 CO 105
5244 RC101 235.0 MAX MT -0.24 -0.58 0.00 0.00 0.00 0.47 CO 201
5248 RC101 235.0 MIN MT -0.24 0.58 0.00 0.00 0.00 -0.47 CO 209
366 RC101 613.4 MAX My -0.18 -0.01 0.06 0.00 0.03 0.02 CO 213
374 RC101 613.4 MIN My -0.13 0.01 -0.05 0.00 -0.03 -0.02 CO 105
5244 RC101 235.0 MAX Mz -0.20 -0.59 0.01 0.00 0.00 0.47 CO 101
5248 RC101 235.0 MIN Mz -0.20 0.59 0.01 0.00 0.00 -0.47 CO 109
Section No. 31: T-Rectangle 40/150
355 RC101 0.0 MAX N 0.08 -0.04 -0.01 0.00 0.01 -0.01 CO 213
359 RC101 535.0 MIN N -0.07 -0.02 -0.02 0.00 -0.01 0.01 CO 105
388 RC101 0.0 MAX Vy 0.00 0.14 0.02 0.00 0.00 0.03 CO 101
390 RC101 0.0 MIN Vy 0.00 -0.14 0.02 0.00 0.00 -0.03 CO 109
264 RC101 0.0 MAX Vz 0.01 0.13 0.05 0.00 -0.01 0.02 CO 201
356 RC101 535.0 MIN Vz 0.01 -0.08 -0.05 0.00 -0.01 0.03 CO 201
353 RC101 535.0 MAX MT -0.06 0.00 -0.05 0.00 -0.01 -0.01 CO 213
357 RC101 535.0 MIN MT -0.01 -0.04 -0.05 0.00 -0.01 0.02 CO 201
200 RC101 450.0 MAX My 0.04 0.00 0.00 0.00 0.03 0.00 CO 213
390 RC101 0.0 MIN My 0.00 0.14 0.03 0.00 -0.01 0.03 CO 101
356 RC101 0.0 MAX Mz 0.01 0.09 -0.01 0.00 0.01 0.03 CO 201
353 RC101 0.0 MIN Mz 0.01 -0.09 -0.01 0.00 0.01 -0.03 CO 209
Section No. 32: Connection_T-Rectangle 40/150
380 RC101 138.5 MAX N 0.25 -0.01 -0.06 0.00 0.00 0.00 CO 201
241 RC101 0.0 MIN N -0.24 -0.01 -0.07 0.00 0.00 0.00 CO 209
381 RC101 0.0 MAX Vy 0.04 0.08 -0.07 0.00 0.00 0.01 CO 213
373 RC101 0.0 MIN Vy 0.04 -0.08 -0.07 0.00 0.00 -0.01 CO 213
208 RC101 0.0 MAX Vz 0.00 0.00 0.00 0.00 0.00 0.00
372 RC101 138.5 MIN Vz -0.22 -0.01 -0.08 0.00 -0.01 0.00 CO 201
373 RC101 0.0 MAX MT 0.03 -0.08 -0.05 0.00 0.00 -0.01 CO 113
381 RC101 0.0 MIN MT 0.03 0.08 -0.05 0.00 0.00 0.01 CO 113
371 RC101 0.0 MAX M y -0.13 0.01 -0.08 0.00 0.00 0.00 CO 201
209 RC101 138.5 MIN My -0.24 0.01 -0.06 0.00 -0.01 0.00 CO 101
381 RC101 0.0 MAX Mz 0.04 0.08 -0.07 0.00 0.00 0.01 CO 213
373 RC101 0.0 MIN Mz 0.04 -0.08 -0.07 0.00 0.00 -0.01 CO 213
Section No. 52: UU 100/100/8/8/8/80/0 (CS_111283_001 | Connector RCS/SRU 1)
5091 RC101 11.5 MAX N 2.02 -5.67 0.33 0.07 0.00 0.06 CO 201

Sheet: 1
Tel: +603-7612 8978 RESULTS

5123 RC101 177.5 MIN N -9.07 37.56 -0.42 -0.08 -0.07 -6.67 CO 209
5123 RC101 0.0 MAX Vy -9.02 37.62 -0.52 -0.05 0.00 0.00 CO 209
300 RC101 72.5 MIN Vy 0.05 -44.51 -0.30 0.09 0.00 0.00 CO 209
292 RC101 10.0 MAX Vz 0.02 4.33 1.24 -0.29 0.00 0.00 CO 101
302 RC101 10.0 MIN Vz 0.02 3.95 -1.31 0.30 0.00 0.00 CO 109
302 RC101 10.0 MAX MT 0.02 3.95 -1.31 0.30 0.00 0.00 CO 109
302 RC101 10.0 MIN MT 0.02 4.24 1.18 -0.29 0.00 0.00 CO 101
5088 RC101 177.5 MAX My -9.04 37.44 0.42 0.08 0.07 -6.65 CO 201
5123 RC101 177.5 MIN My -9.07 37.56 -0.42 -0.08 -0.07 -6.67 CO 209
5091 RC101 115.0 MAX Mz 2.02 -5.64 0.34 0.08 0.04 0.65 CO 201
5123 RC101 177.5 MIN Mz -9.07 37.56 -0.42 -0.08 -0.07 -6.67 CO 209
Section No. 53: RHH 100x50x6.3 | Continental Steel (CS_111283_003 | Connector RCS/SRU)
5155 RC101 0.0 MAX N 15.09 -0.10 0.52 0.01 0.02 -0.02 CO 209
5133 RC101 0.0 MIN N -82.03 -0.71 -10.10 0.05 2.54 -0.18 CO 209
5138 RC101 250.0 MAX Vy 2.68 1.36 -0.56 -0.01 0.03 0.00 CO 101
5138 RC101 250.0 MIN Vy 3.74 -1.37 -0.07 0.01 0.04 0.00 CO 109
5140 RC101 100.0 MAX Vz -0.80 0.04 2.52 0.00 -0.39 0.01 CO 205
5098 RC101 250.0 MIN Vz -81.56 0.72 -10.17 -0.07 0.00 0.00 CO 201
5133 RC101 250.0 MAX MT -81.97 -0.72 -10.17 0.07 0.00 0.00 CO 209
5098 RC101 250.0 MIN MT -81.56 0.72 -10.17 -0.07 0.00 0.00 CO 201
5098 RC101 0.0 MAX My -81.63 0.71 -10.10 -0.05 2.54 0.18 CO 201
5140 RC101 0.0 MIN My -0.82 0.04 2.52 0.00 -0.65 0.01 CO 205
5138 RC101 0.0 MAX Mz 2.73 1.36 -0.56 0.00 0.16 0.34 CO 101
5138 RC101 0.0 MIN Mz 3.80 -1.37 -0.07 0.01 0.05 -0.34 CO 109
Section No. 54: RHH 100x50x6.3 | Continental Steel (CS_111283_002 | Connector RCS/SRU Welding)
5151 RC101 0.0 MAX N 15.11 -0.10 0.52 0.01 -0.01 -0.03 CO 209
5127 RC101 0.0 MIN N -82.05 0.03 -9.12 0.11 3.09 -0.18 CO 209
5131 RC101 60.1 MAX Vy 2.73 1.36 -0.56 0.00 0.16 0.34 CO 101
5131 RC101 60.1 MIN Vy 3.80 -1.37 -0.07 0.01 0.05 -0.34 CO 109
5110 RC101 0.0 MAX Vz 11.52 0.43 2.02 -0.04 -0.51 0.13 CO 201
5127 RC101 60.1 MIN Vz -82.03 0.02 -9.15 0.11 2.54 -0.18 CO 209
5127 RC101 60.1 MAX MT -82.03 0.02 -9.15 0.11 2.54 -0.18 CO 209
5092 RC101 60.1 MIN MT -81.63 -0.02 -9.12 -0.11 2.54 0.18 CO 201
5127 RC101 0.0 MAX My -82.05 0.03 -9.12 0.11 3.09 -0.18 CO 209
5105 RC101 0.0 MIN My -0.84 -0.03 1.55 0.00 -0.80 0.01 CO 205
5131 RC101 0.0 MAX Mz 2.74 1.36 -0.56 0.01 0.20 0.42 CO 101
5131 RC101 0.0 MIN Mz 3.81 -1.37 -0.07 0.01 0.06 -0.42 CO 109
Section No. 55: Connection_2UR U 120-52/X | DIN 1026-1:1963 (CS_111283_102 | Connection to SRU RCS/SRU)
289 RC101 0.0 MAX N 10.16 1.39 -81.55 0.00 0.00 -0.07 CO 201
291 RC101 10.0 MIN N -2.53 -0.01 -11.90 0.00 -0.12 0.00 CO 213
289 RC101 20.0 MAX Vy 10.16 1.39 -81.55 0.11 -1.63 -0.09 CO 201
299 RC101 20.0 MIN Vy 10.16 -1.39 -81.95 -0.11 -1.63 0.09 CO 209
5143 RC101 20.0 MAX Vz -0.25 -0.08 0.01 0.00 0.00 0.00 CO 109
299 RC101 20.0 MIN Vz 10.16 -1.39 -81.95 -0.11 -1.63 0.09 CO 209
289 RC101 20.0 MAX MT 10.16 1.39 -81.55 0.11 -1.63 -0.09 CO 201
299 RC101 20.0 MIN MT 10.16 -1.39 -81.95 -0.11 -1.63 0.09 CO 209
315 RC101 0.0 MAX My -2.02 0.02 -0.76 0.00 0.02 0.00 CO 213
299 RC101 20.0 MIN My 10.16 -1.39 -81.95 -0.11 -1.63 0.09 CO 209
299 RC101 20.0 MAX Mz 10.16 -1.39 -81.95 -0.11 -1.63 0.09 CO 209
289 RC101 20.0 MIN Mz 10.16 1.39 -81.55 0.11 -1.63 -0.09 CO 201
Section No. 56: Connection_2UR U 200-82/X | DIN 1026-1:1963 (CS_111283_101 | Connection To Connector RCS/SRU)
5067 RC101 72.9 MAX N 19.07 0.01 0.00 0.00 0.00 0.00 CO 213
5075 RC101 56.7 MIN N -44.52 0.10 0.00 0.00 0.00 0.08 CO 209
5067 RC101 81.0 MAX Vy 4.32 1.36 0.01 0.00 0.00 -0.40 CO 101
5077 RC101 81.0 MIN Vy 3.94 -1.42 0.02 0.00 0.00 0.41 CO 109
5074 RC101 0.0 MAX Vz -37.62 0.70 9.08 0.00 0.00 0.05 CO 209
5070 RC101 81.0 MIN Vz 5.70 -0.29 -2.03 -0.01 -0.16 -0.04 CO 201
5080 RC101 81.0 MAX MT 5.66 0.29 -2.01 0.01 -0.16 0.05 CO 209
5070 RC101 81.0 MIN MT 5.70 -0.29 -2.03 -0.01 -0.16 -0.04 CO 201
5074 RC101 81.0 MAX My -37.62 0.70 9.07 0.00 0.73 -0.01 CO 209
5070 RC101 81.0 MIN My 5.70 -0.29 -2.03 -0.01 -0.16 -0.04 CO 201
5077 RC101 81.0 MAX Mz 3.94 -1.42 0.02 0.00 0.00 0.41 CO 109
5077 RC101 81.0 MIN Mz 4.23 1.30 0.01 0.00 0.00 -0.40 CO 101

Sheet: 1
Tel: +603-7612 8978 RESULTS
4.4 NODES - SUPPORT FORCES Result Combinations

Node Support Forces [kN] Support Moments [kNm] Corresponding
No. RC PX' PY' PZ' MX' MY' MZ' Load Cases
28 RC103 Max PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Min PZ' 0.00 0.00 -36.22 0.00 0.00 0.00 CO 601
31 RC103 Max PX' 2.64 0.00 -2.36 0.00 0.00 0.00 CO 602
Min PX' 0.00 0.00 0.00 0.00 0.00 0.00
Max PY' 2.18 0.00 -1.95 0.00 0.00 0.00 CO 601
Min PY' 2.30 0.00 -2.05 0.00 0.00 0.00 CO 603
Max PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Min PZ' 2.64 0.00 -2.36 0.00 0.00 0.00 CO 602
Max MX' 2.18 0.00 -1.95 0.00 0.00 0.00 CO 601
Min MX' 2.30 0.00 -2.05 0.00 0.00 0.00 CO 603
32 RC103 Max PX' 0.00 0.00 0.00 0.00 0.00 0.00
Min PX' -7.06 4.95 70.55 0.09 0.00 0.00 CO 601
Max PY' -3.01 5.11 30.07 -0.15 0.00 0.00 CO 501
Min PY' -2.49 -5.04 24.87 0.16 0.00 0.00 CO 503
Max PZ' -7.06 4.95 70.55 0.09 0.00 0.00 CO 601
Min PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Max MX' -2.49 -5.04 24.87 0.16 0.00 0.00 CO 503
Min MX' -3.01 5.11 30.07 -0.15 0.00 0.00 CO 501
33 RC103 Max PX' 0.00 0.00 0.00 0.00 0.00 0.00
Min PX' 0.00 0.00 0.00 0.00 0.00 0.00
Max PY' 0.00 2.58 0.00 0.30 0.00 0.00 CO 603
Min PY' 0.00 -2.62 0.00 -0.31 0.00 0.00 CO 601
Max PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Min PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Max MX' 0.00 2.58 0.00 0.30 0.00 0.00 CO 603
Min MX' 0.00 -2.62 0.00 -0.31 0.00 0.00 CO 601
67 RC103 Max PX' 5.42 0.00 0.69 0.00 0.00 0.00 CO 602
Min PX' 0.00 0.00 0.00 0.00 0.00 0.00
Max PY' 4.47 0.01 0.57 0.00 0.00 0.00 CO 601
Min PY' 4.71 -0.01 0.60 0.00 0.00 0.00 CO 603
Max PZ' 5.42 0.00 0.69 0.00 0.00 0.00 CO 602
Min PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Max MX' 4.47 0.01 0.57 0.00 0.00 0.00 CO 601
Min MX' 4.71 -0.01 0.60 0.00 0.00 0.00 CO 603
105 RC103 Max PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Min PZ' 0.00 0.00 -36.38 0.00 0.00 0.00 CO 603
108 RC103 Max PX' 2.64 0.00 -2.37 0.00 0.00 0.00 CO 602
Min PX' 0.00 0.00 0.00 0.00 0.00 0.00
Max PY' 2.30 0.00 -2.06 0.00 0.00 0.00 CO 601
Min PY' 2.18 0.00 -1.95 0.00 0.00 0.00 CO 603
Max PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Min PZ' 2.64 0.00 -2.37 0.00 0.00 0.00 CO 602
Max MX' 2.30 0.00 -2.06 0.00 0.00 0.00 CO 601
Min MX' 2.18 0.00 -1.95 0.00 0.00 0.00 CO 603
109 RC103 Max PX' 0.00 0.00 0.00 0.00 0.00 0.00
Min PX' -7.07 -4.96 70.72 -0.09 0.00 0.00 CO 603
Max PY' -2.50 5.08 25.04 -0.16 0.00 0.00 CO 501
Min PY' -3.02 -5.12 30.24 0.15 0.00 0.00 CO 503
Max PZ' -7.07 -4.96 70.72 -0.09 0.00 0.00 CO 603
Min PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Max MX' -3.02 -5.12 30.24 0.15 0.00 0.00 CO 503
Min MX' -2.50 5.08 25.04 -0.16 0.00 0.00 CO 501
110 RC103 Max PX' 0.00 0.00 0.00 0.00 0.00 0.00
Min PX' 0.00 0.00 0.00 0.00 0.00 0.00
Max PY' 0.00 2.62 0.00 0.31 0.00 0.00 CO 603
Min PY' 0.00 -2.60 0.00 -0.31 0.00 0.00 CO 601
Max PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Min PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Max MX' 0.00 2.62 0.00 0.31 0.00 0.00 CO 603
Min MX' 0.00 -2.60 0.00 -0.31 0.00 0.00 CO 601
164 RC103 Max PX' 5.42 0.00 0.69 0.00 0.00 0.00 CO 602
Min PX' 0.00 0.00 0.00 0.00 0.00 0.00
Max PY' 4.72 0.01 0.60 0.00 0.00 0.00 CO 601
Min PY' 4.47 -0.01 0.57 0.00 0.00 0.00 CO 603
Max PZ' 5.42 0.00 0.69 0.00 0.00 0.00 CO 602
Min PZ' 0.00 0.00 0.00 0.00 0.00 0.00
Max MX' 4.72 0.01 0.60 0.00 0.00 0.00 CO 601
Min MX' 4.47 -0.01 0.57 0.00 0.00 0.00 CO 603
599 RC103 Max PX' 0.00 -0.40 -0.36 0.00 0.00 0.00 CO 603
Min PX' 0.00 0.00 0.00 0.00 0.00 0.00
Max PY' 0.00 0.43 0.46 0.00 0.00 0.00 CO 601
Min PY' 0.00 -0.40 -0.36 0.00 0.00 0.00 CO 603
Max PZ' 0.00 0.43 0.46 0.00 0.00 0.00 CO 601
Min PZ' 0.00 -0.40 -0.36 0.00 0.00 0.00 CO 603
Max MX' 0.00 0.00 0.00 0.00 0.00 0.00
Min MX' 0.00 0.00 0.00 0.00 0.00 0.00
Max MY' 0.00 0.00 0.00 0.00 0.00 0.00
Min MY' 0.00 0.00 0.00 0.00 0.00 0.00
Max MZ' 0.00 0.00 0.00 0.00 0.00 0.00
Min MZ' 0.00 0.00 0.00 0.00 0.00 0.00
600 RC103 Max PX' 0.00 0.40 -0.36 0.00 0.00 0.00 CO 601
Min PX' 0.00 0.00 0.00 0.00 0.00 0.00
Max PY' 0.00 0.40 -0.36 0.00 0.00 0.00 CO 601
Min PY' 0.00 -0.43 0.46 0.00 0.00 0.00 CO 603
Max PZ' 0.00 -0.43 0.46 0.00 0.00 0.00 CO 603
Min PZ' 0.00 0.40 -0.36 0.00 0.00 0.00 CO 601

Sheet: 1
Tel: +603-7612 8978 RESULTS
4.4 NODES - SUPPORT FORCES Result Combinations

Node Support Forces [kN] Support Moments [kNm] Corresponding
No. RC PX' PY' PZ' MX' MY' MZ' Load Cases
600 Max MX' 0.00 0.00 0.00 0.00 0.00 0.00
Min MX' 0.00 0.00 0.00 0.00 0.00 0.00
Max MY' 0.00 0.00 0.00 0.00 0.00 0.00
Min MY' 0.00 0.00 0.00 0.00 0.00 0.00
Max MZ' 0.00 0.00 0.00 0.00 0.00 0.00
Min MZ' 0.00 0.00 0.00 0.00 0.00 0.00

Sheet: 1
Tel: +603-7612 8978 RESULTS
SUPPORT REACTIONS
Against Y-direction
800 mm
M 1:40
70.72
7.07
36.38
Max P-Z': 70.72, Min P-Z': -36.38 kN

RC103 : Authoritative Load Case SLS
Max P-X': 5.42, Min P-X': -7.07 kN

2.64 5.42
0.69
2.37

Sheet: 1
Tel: +603-7612 8978 RESULTS
SUPPORT REACTIONS
0.43
In X-direction
600 mm
0.46
M 1:30
0.40
0.36
5.11
70.55
5.04
5.08
70.72
5.12
Max P-Z': 70.72, Min P-Z': -0.36 kN

RC103 : Authoritative Load Case SLS
Max P-Y': 5.11, Min P-Y': -5.12 kN

0.40
0.46
0.43
0.36

Sheet: 1
Tel: +603-7612 8978 STEEL

STEEL
CA1
Storm Condition 1.1.1 GENERAL DATA
Members to design: All
Load combinations to design: CO101 1.35G1 + 1.35G2 + 1.5Qi3 + 1.5Qw1 + Imp1 + Imp3
CO102 1.35G1 + 1.35G2 + 1.5Qi3 + 1.5Qw1 + Imp1 + Imp4
CO103 1.35G1 + 1.35G2 + 1.5Qi3 + 1.5Qw1 + Imp2 + Imp3
CO104 1.35G1 + 1.35G2 + 1.5Qi3 + 1.5Qw1 + Imp2 + Imp4
CO105 1.35G1 + 1.35G2 + 1.5Qi3 + 1.5Qw2 + Imp1 + Imp3
CO106 1.35G1 + 1.35G2 + 1.5Qi3 + 1.5Qw2 + Imp1 + Imp4
CO107 1.35G1 + 1.35G2 + 1.5Qi3 + 1.5Qw2 + Imp2 + Imp3
CO108 1.35G1 + 1.35G2 + 1.5Qi3 + 1.5Qw2 + Imp2 + Imp4
CO109 1.35G1 + 1.35G2 + 1.5Qi3 - 1.5Qw1 - Imp1 - Imp3
CO110 1.35G1 + 1.35G2 + 1.5Qi3 - 1.5Qw1 - Imp1 - Imp4
CO111 1.35G1 + 1.35G2 + 1.5Qi3 - 1.5Qw1 - Imp2 - Imp3
CO112 1.35G1 + 1.35G2 + 1.5Qi3 - 1.5Qw1 - Imp2 - Imp4
CO113 1.35G1 + 1.35G2 + 1.5Qi3 - 1.5Qw2 - Imp1 - Imp3
CO114 1.35G1 + 1.35G2 + 1.5Qi3 - 1.5Qw2 - Imp1 - Imp4
CO115 1.35G1 + 1.35G2 + 1.5Qi3 - 1.5Qw2 - Imp2 - Imp3
CO116 1.35G1 + 1.35G2 + 1.5Qi3 - 1.5Qw2 - Imp2 - Imp4
1.2 MATERIALS
Matl. Material Safety Factor Yield Strength Limit Stresses [kN/cm 2]
No. Description M [-] fyk [kN/cm2] Manually Limit x Limit  Limit eqv
1 PM_S235_B1 1.10 23.50 21.36 12.33 21.36
2 PM_S355_B1 1.10 35.50 32.27 18.63 32.27
4 PM_Steel_Dummy 1.10 20.43 18.57 10.72 18.57
2UR U 200-5/0.1 | - 2UR U 120-5/0.1 | -

1.3.1 CROSS-SECTIONS
Sect. Matl. Cross-section It [cm4] Iy [cm4] Iz [cm4]
No. No. Description A [cm2] pl,y pl,z Comment
1 2 2UR U 200-5/0.1 29.57 3820.00 624.93
RO 88.9x4.5 RO 88.9x5
64.40 1.19 1.81 CS_RCS_001 | RCS
2 1 2UR U 120-5/0.1 9.88 728.00 202.76
34.00 1.20 1.79 CS_SRU_001 |
SRU_Section A
3 1 2UR U 120-5/0.1 9.88 728.00 202.76
34.00 1.20 1.79 CS_SRU_002 |
SRU_Section B
4 1 RO 88.9x4.5 | Mannesmann 213.09 106.54 106.54
11.93 1.34 1.34 CS_111035_002 | SLS
IUH 240/80/60/28/8... 40/80_SRU
5 1 RO 88.9x5 | Mannesmann 232.75 116.37 116.37
13.18 1.35 1.35 CS_101776_002 | SLS
140/240_SRU
6 2 RO 88.9x5 | Mannesmann 232.75 116.37 116.37
13.18 1.35 1.35 CS_109726_002 | SLS
320/420_SRU
7 4 Fitting pin 21mm_RCS-rail 21.33 3820.00 296.00
64.40 1.00 1.00 Connection with fitting pin
RO 48.3x3.2
21mm to RCS-rail
The section cannot be designed because the cross-section data is not defined!
64.40 1.00 1.00 CS_PROP_PEP
RO 60.3x2.3 QRO 35x35x2 9 4 Fitting pin 26mm_RCS-rail 21.33 3820.00 296.00
26mm to RCS-rail
10 4 Fitting pin 21mm_SRU-waler 7.27 728.00 86.40
T-Rectangle 40/150
21mm to SRU-waler
11 6 IUH 240/80/60/28/80/60 806.37 8467.20 533.95
UU 100/100/8/8/8/... RHH 100x50x6.3
129.60 1.00 1.00 CS_GT24_001
The section cannot be designed because the characteristic stresses are invalid!
13 6 Connection GT24 806.37 8467.20 533.95
129.60 1.00 1.00 CS_GT24_002
15 4 Connection 5.97 777.60 278.30
28.80 1.00 1.00 Dummy connection stiffness
for 2x8mm sheets
25 1 RO 48.3x3.2 | DIN EN 10220 23.17 11.59 11.59
4.53 1.36 1.36 CS_SCAFFOLD
26 4 Connection_RO 48.3x3.2 | DIN EN 23.17 11.59 11.59
10220
4.53 1.00 1.00 CS_SCAFFOLD_CON
10220
4.53 1.00 1.00 Half Coupler
28 1 RO 60.3x2.3 | DIN EN 10220 35.30 17.65 17.65
4.19 1.32 1.32 CS_PUSH_PULL_01
29 1 QRO 35x35x2 | ALUKÖNIGSTAHL - 7.27 4.71 4.71
EN 10305/5 (DIN 2395)
2.61 1.17 1.17 CS_116292_001
31 5 T-Rectangle 40/150 266.26 1125.00 80.00
60.00 1.00 1.00
32 6 Connection_T-Rectangle 40/150 266.26 1125.00 80.00

Sheet: 1
Tel: +603-7612 8978 STEEL
60.00 1.00 1.00
52 2 UU 100/100/8/8/8/80/0 4.42 225.69 215.68
21.12 1.17 1.69 CS_111283_001 |
Connector RCS/SRU 1
53 2 RHH 100x50x6.3 | Continental Steel 160.00 197.00 63.00
16.90 1.30 1.22 CS_111283_003 |
Connector RCS/SRU
16.90 1.30 1.22 CS_111283_002 |
Connector RCS/SRU
Welding
55 4 Connection_2UR U 120-52/X | DIN 7.27 728.00 86.40
1026-1:1963
34.00 1.00 1.00 CS_111283_102 |
Connection to SRU
RCS/SRU
1026-1:1963
64.40 1.00 1.00 CS_111283_101 |
Connection To Connector
RCS/SRU
2.1 STRESSES BY CROSS-SECTION

Sect. Member Location S-Point Load Stress [kN/cm 2] Stress
No. No. x [mm] No. Case Stress Type Existing Limit Ratio
1 2UR U 200-5/0.1 - CS_RCS_001 | RCS
117 0.0 14 CO101 Sigma Total -12.84 32.27 0.40
120 0.0 4 CO109 Tau Total 4.80 18.63 0.26
120 0.0 7 CO109 Sigma-eqv 14.86 32.27 0.46
2 2UR U 120-5/0.1 - CS_SRU_001 | SRU_Section A

157 0.0 8 CO109 Sigma Total -4.67 21.36 0.22
65 0.0 11 CO109 Tau Total -1.94 12.33 0.16
157 0.0 8 CO109 Sigma-eqv 4.69 21.36 0.22
3 2UR U 120-5/0.1 - CS_SRU_002 | SRU_Section B

64 0.0 1 CO109 Sigma Total -3.34 21.36 0.16
64 0.0 11 CO109 Tau Total 0.71 12.33 0.06
64 0.0 9 CO109 Sigma-eqv 3.51 21.36 0.16
4 RO 88.9x4.5 | Mannesmann - CS_111035_002 | SLS 40/80_SRU

91 290.1 28 CO105 Sigma Total 0.50 21.36 0.02
45 580.3 19 CO113 Tau Total 0.01 12.33 0.00
91 290.1 28 CO105 Sigma-eqv 0.50 21.36 0.02
5 RO 88.9x5 | Mannesmann - CS_101776_002 | SLS 140/240_SRU

158 1137.5 29 CO109 Sigma Total 3.07 21.36 0.14
156 2275.0 20 CO109 Tau Total 0.02 12.33 0.00
158 1137.5 29 CO109 Sigma-eqv 3.07 21.36 0.14

67 1932.7 28 CO109 Sigma Total 3.01 32.27 0.09
17 3865.4 19 CO109 Tau Total 0.04 18.63 0.00
67 1932.7 28 CO109 Sigma-eqv 3.01 32.27 0.09
25 RO 48.3x3.2 | DIN EN 10220 - CS_SCAFFOLD

131 2378.9 10 CO101 Sigma Total -4.04 21.36 0.19
129 150.0 25 CO109 Tau Total -0.65 12.33 0.05
131 2378.9 10 CO101 Sigma-eqv 4.04 21.36 0.19
28 RO 60.3x2.3 | DIN EN 10220 - CS_PUSH_PULL_01

5352 887.4 10 CO109 Sigma Total -0.38 21.36 0.02
5352 1774.8 19 CO109 Tau Total 0.02 12.33 0.00
5352 887.4 10 CO109 Sigma-eqv 0.38 21.36 0.02
29 QRO 35x35x2 | ALUKÖNIGSTAHL - EN 10305/5 (DIN 2395) - CS_116292_001

5244 235.0 15 CO101 Sigma Total -17.63 21.36 0.83
5248 235.0 12 CO109 Tau Total -0.51 12.33 0.04
5244 235.0 15 CO101 Sigma-eqv 17.64 21.36 0.83
52 UU 100/100/8/8/8/80/0 - CS_111283_001 | Connector RCS/SRU 1

5123 177.5 1 CO109 Sigma Total 7.40 32.27 0.23
302 10.0 2 CO109 Tau Total -5.84 18.63 0.31
302 10.0 2 CO109 Sigma-eqv 10.11 32.27 0.31
53 RHH 100x50x6.3 | Continental Steel - CS_111283_003 | Connector RCS/SRU

5133 0.0 5 CO109 Sigma Total -4.61 32.27 0.14
5098 250.0 16 CO101 Tau Total -0.44 18.63 0.02
5133 0.0 5 CO109 Sigma-eqv 4.62 32.27 0.14
54 RHH 100x50x6.3 | Continental Steel - CS_111283_002 | Connector RCS/SRU Welding

5127 0.0 5 CO109 Sigma Total -5.17 32.27 0.16
5127 60.1 8 CO109 Tau Total 0.47 18.63 0.03
5127 0.0 5 CO109 Sigma-eqv 5.18 32.27 0.16

Sheet: 1
Tel: +603-7612 8978 RS-STAHL Stabe
STRESS RATIO Sigma-eqv

Isometric
800 mm
M 1:40
Max Sigma-eqv: 0.83, Min Sigma-eqv: 0.00
1.00
0.90
0.80
0.70
0.60
0.50
0.40
0.30
0.20
0.10
0.00
0.83
0.00
Sigma-eqv [-]
STEEL CA1
Stress ratio
Max :
Min :

Sheet: 1
Tel: +603-7612 8978 STEEL

STEEL
CA2
In-Operation Condition 1.1.1 GENERAL DATA
Members to design: All
Load combinations to design: CO201 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 + 1.5Qi6 +
1.5Qi8 + 1.5Qw3 + Imp1 + Imp3
CO202 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 + 1.5Qi6 +
1.5Qi8 + 1.5Qw3 + Imp1 + Imp4
CO203 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 + 1.5Qi6 +
1.5Qi8 + 1.5Qw3 + Imp2 + Imp3
CO204 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 + 1.5Qi6 +
1.5Qi8 + 1.5Qw3 + Imp2 + Imp4
CO205 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 + 1.5Qi7 +
1.5Qi8 + 1.5Qw4 + Imp1 + Imp3
CO206 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 + 1.5Qi7 +
1.5Qi8 + 1.5Qw4 + Imp1 + Imp4
CO207 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 + 1.5Qi7 +
1.5Qi8 + 1.5Qw4 + Imp2 + Imp3
CO208 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 + 1.5Qi7 +
1.5Qi8 + 1.5Qw4 + Imp2 + Imp4
CO209 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 - 1.5Qi6 +
1.5Qi8 - 1.5Qw3 - Imp1 - Imp3
CO210 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 - 1.5Qi6 +
1.5Qi8 - 1.5Qw3 - Imp1 - Imp4
CO211 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 - 1.5Qi6 +
1.5Qi8 - 1.5Qw3 - Imp2 - Imp3
CO212 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 - 1.5Qi6 +
1.5Qi8 - 1.5Qw3 - Imp2 - Imp4
CO213 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 - 1.5Qi7 +
1.5Qi8 - 1.5Qw4 - Imp1 - Imp3
CO214 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 - 1.5Qi7 +
1.5Qi8 - 1.5Qw4 - Imp1 - Imp4
CO215 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 - 1.5Qi7 +
1.5Qi8 - 1.5Qw4 - Imp2 - Imp3
CO216 1.35G1 + 1.35G2 + 1.5Qi1 + 1.5Qi2 + 1.5Qi4 - 1.5Qi7 +
1.5Qi8 - 1.5Qw4 - Imp2 - Imp4
1.2 MATERIALS
Matl. Material Safety Factor Yield Strength Limit Stresses [kN/cm 2]
No. Description M [-] fyk [kN/cm2] Manually Limit x Limit  Limit eqv
1 PM_S235_B1 1.10 23.50 21.36 12.33 21.36
2 PM_S355_B1 1.10 35.50 32.27 18.63 32.27
4 PM_Steel_Dummy 1.10 20.43 18.57 10.72 18.57
2UR U 200-5/0.1 | - 2UR U 120-5/0.1 | -

1 2 2UR U 200-5/0.1 29.57 3820.00 624.93
RO 88.9x4.5 RO 88.9x5
64.40 1.19 1.81 CS_RCS_001 | RCS
2 1 2UR U 120-5/0.1 9.88 728.00 202.76
34.00 1.20 1.79 CS_SRU_001 |
SRU_Section A
3 1 2UR U 120-5/0.1 9.88 728.00 202.76
34.00 1.20 1.79 CS_SRU_002 |
SRU_Section B
4 1 RO 88.9x4.5 | Mannesmann 213.09 106.54 106.54
11.93 1.34 1.34 CS_111035_002 | SLS
IUH 240/80/60/28/8... 40/80_SRU
5 1 RO 88.9x5 | Mannesmann 232.75 116.37 116.37
13.18 1.35 1.35 CS_101776_002 | SLS
140/240_SRU
6 2 RO 88.9x5 | Mannesmann 232.75 116.37 116.37
13.18 1.35 1.35 CS_109726_002 | SLS
320/420_SRU
RO 48.3x3.2
21mm to RCS-rail
64.40 1.00 1.00 CS_PROP_PEP
RO 60.3x2.3 QRO 35x35x2 9 4 Fitting pin 26mm_RCS-rail 21.33 3820.00 296.00
26mm to RCS-rail
10 4 Fitting pin 21mm_SRU-waler 7.27 728.00 86.40
T-Rectangle 40/150
21mm to SRU-waler
11 6 IUH 240/80/60/28/80/60 806.37 8467.20 533.95
UU 100/100/8/8/8/... RHH 100x50x6.3
129.60 1.00 1.00 CS_GT24_001
13 6 Connection GT24 806.37 8467.20 533.95
129.60 1.00 1.00 CS_GT24_002
15 4 Connection 5.97 777.60 278.30
28.80 1.00 1.00 Dummy connection stiffness
for 2x8mm sheets
25 1 RO 48.3x3.2 | DIN EN 10220 23.17 11.59 11.59
4.53 1.36 1.36 CS_SCAFFOLD
26 4 Connection_RO 48.3x3.2 | DIN EN 1 23.17 11.59 11.59

Sheet: 1
Tel: +603-7612 8978 STEEL
10220
4.53 1.00 1.00 CS_SCAFFOLD_CON
10220
4.53 1.00 1.00 Half Coupler
28 1 RO 60.3x2.3 | DIN EN 10220 35.30 17.65 17.65
4.19 1.32 1.32 CS_PUSH_PULL_01
29 1 QRO 35x35x2 | ALUKÖNIGSTAHL - 7.27 4.71 4.71
EN 10305/5 (DIN 2395)
2.61 1.17 1.17 CS_116292_001
31 5 T-Rectangle 40/150 266.26 1125.00 80.00
60.00 1.00 1.00
32 6 Connection_T-Rectangle 40/150 266.26 1125.00 80.00
60.00 1.00 1.00
52 2 UU 100/100/8/8/8/80/0 4.42 225.69 215.68
21.12 1.17 1.69 CS_111283_001 |
Connector RCS/SRU 1
16.90 1.30 1.22 CS_111283_003 |
Connector RCS/SRU
16.90 1.30 1.22 CS_111283_002 |
Connector RCS/SRU
Welding
1026-1:1963
34.00 1.00 1.00 CS_111283_102 |
Connection to SRU
RCS/SRU
1026-1:1963
64.40 1.00 1.00 CS_111283_101 |
Connection To Connector
RCS/SRU

1 2UR U 200-5/0.1 - CS_RCS_001 | RCS
117 0.0 14 CO201 Sigma Total -17.91 32.27 0.55
120 0.0 4 CO209 Tau Total 4.76 18.63 0.26
117 0.0 14 CO201 Sigma-eqv 18.56 32.27 0.58
2 2UR U 120-5/0.1 - CS_SRU_001 | SRU_Section A

157 0.0 8 CO209 Sigma Total -13.15 21.36 0.62
65 0.0 11 CO209 Tau Total -5.62 12.33 0.46
157 0.0 8 CO209 Sigma-eqv 13.28 21.36 0.62
3 2UR U 120-5/0.1 - CS_SRU_002 | SRU_Section B

64 0.0 8 CO209 Sigma Total -9.23 21.36 0.43
64 0.0 11 CO209 Tau Total 2.21 12.33 0.18
64 0.0 8 CO209 Sigma-eqv 9.67 21.36 0.45
4 RO 88.9x4.5 | Mannesmann - CS_111035_002 | SLS 40/80_SRU

91 290.1 28 CO205 Sigma Total 1.03 21.36 0.05
45 580.3 19 CO213 Tau Total 0.01 12.33 0.00
91 290.1 28 CO205 Sigma-eqv 1.03 21.36 0.05

158 1137.5 29 CO209 Sigma Total 7.18 21.36 0.34
156 2275.0 20 CO209 Tau Total 0.02 12.33 0.00
158 1137.5 29 CO209 Sigma-eqv 7.18 21.36 0.34

67 1932.7 28 CO209 Sigma Total 5.95 32.27 0.18
17 3865.4 19 CO209 Tau Total 0.03 18.63 0.00
67 1932.7 28 CO209 Sigma-eqv 5.95 32.27 0.18
25 RO 48.3x3.2 | DIN EN 10220 - CS_SCAFFOLD

131 2378.9 10 CO201 Sigma Total -3.95 21.36 0.18
129 150.0 25 CO209 Tau Total -0.57 12.33 0.05
131 2378.9 10 CO201 Sigma-eqv 3.95 21.36 0.19
28 RO 60.3x2.3 | DIN EN 10220 - CS_PUSH_PULL_01

5351 887.4 10 CO201 Sigma Total -0.57 21.36 0.03
5352 1774.8 19 CO209 Tau Total 0.02 12.33 0.00
5351 887.4 10 CO201 Sigma-eqv 0.57 21.36 0.03
29 QRO 35x35x2 | ALUKÖNIGSTAHL - EN 10305/5 (DIN 2395) - CS_116292_001

5244 235.0 1 CO201 Sigma Total -17.52 21.36 0.82
5309 235.0 12 CO209 Tau Total -0.57 12.33 0.05
5244 235.0 1 CO201 Sigma-eqv 17.52 21.36 0.82
52 UU 100/100/8/8/8/80/0 - CS_111283_001 | Connector RCS/SRU 1

5123 177.5 1 CO209 Sigma Total 18.62 32.27 0.58

Sheet: 1
Tel: +603-7612 8978 STEEL

300 72.5 5 CO209 Tau Total -5.52 18.63 0.30
5123 177.5 1 CO209 Sigma-eqv 18.78 32.27 0.58
53 RHH 100x50x6.3 | Continental Steel - CS_111283_003 | Connector RCS/SRU

5133 0.0 5 CO209 Sigma Total -11.74 32.27 0.36
5098 250.0 16 CO201 Tau Total -1.20 18.63 0.06
5133 0.0 5 CO209 Sigma-eqv 11.75 32.27 0.36
54 RHH 100x50x6.3 | Continental Steel - CS_111283_002 | Connector RCS/SRU Welding

5127 0.0 5 CO209 Sigma Total -13.13 32.27 0.41
5127 60.1 8 CO209 Tau Total 1.20 18.63 0.06
5127 0.0 5 CO209 Sigma-eqv 13.17 32.27 0.41

Sheet: 1
Tel: +603-7612 8978 RS-STAHL Stabe
STRESS RATIO Sigma-eqv

Isometric
800 mm
M 1:40
Max Sigma-eqv: 0.82, Min Sigma-eqv: 0.00
1.00
0.90
0.80
0.70
0.60
0.50
0.40
0.30
0.20
0.10
0.00
0.82
0.00
Sigma-eqv [-]
STEEL CA2
Stress ratio
Max :
Min :

75-0001128 - 0 Calculation Landing Platform - KVN Signed

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

75-0001128 - 0 Calculation Landing Platform - KVN Signed

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

75-0001128 - 0 Calculation Landing Platform - KVN Signed

Uploaded by

Copyright:

Available Formats

Design Report

OASIS - LANDING PLATFORM

Client JO CSCODS - TAISEI

Document-No 1465_S001_LANDING PLATFORM

1 Preliminary remarks........................................................................................................................ ..........5

2 Codes and references...................................................................................................................... ..........6

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 2 | 24

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 3 | 24

Revision Date Name Remarks

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 4 | 24

1.2 Design Class and Partial Safety Factors

1.3 Considered safety factors

1.3.1 Partial safety factors for material

1.3.2 Partial safety factors for loads

1.3.3 Partial safety factor for Shoring systems

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 5 | 24

2 Codes and references

1. EN 12812 Falsework – Performance requirements and general design

1. PERI Design Tables Formwork and Shoring (2015)

1. PERICAD Static Tools

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 6 | 24

The following drawings are associated to the project:

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 7 | 24

qgt24 = Girder GT24 = 0.06 kN/m

4.2 Variable persistent vertical actions (Q2)

W platform = Width of platform 3.32 m

q2.3.1 = Operations loading on platform = 35.20 / 14.44 = 2.44 kN/m²

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 8 | 24

4.3 Wind Load (Q5)

qmax,x = Maximum wind pressure = 0.20 kN/m²

qwork,x = Wind pressure in working condition = 0.20 kN/m²

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 9 | 24

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 10 | 24

5.1 Formwork Girder GT 24

Forces VEd [kN] MEd [kNcm] Fm,Ed [kN] Mm,Ed [kNcm]

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 11 | 24

5.2 Hook Strap Uni HBU 24-26

Loading: Long Term

Resistance NRd [kN]

Internal Force NEd [kN]

5.3 Climbing Rail RCS 3D

Cross-Section: 2 x U 200 (EN 1026) (Class 1 acc. to EN 1993-1-1 table 5.2)

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 12 | 24

5.4 Steel Waler SRU

Resistances NRd [kN] Vz,Rd [kN] My,Rd [kNcm]

Internal Forces NEd [kN] Vz,Ed [kN] My,Ed [kNcm]

Verification n v m n-v* v-m* n-v-m*

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 13 | 24

5.5 Angle Connector RCS/SRU

Resistances Npl,Rd [kN] Vpl,z,Rd [kN] Mpl,y,Rd [kNcm]

Internal Forces NEd [kN] Vz,Ed [kN] My,Ed [kNcm]

5.5.2 Weld Seam

Cross-Section: RHS 154x54x4

Resistances Npl,Rd [kN] Vpl,z,Rd [kN] Mpl,y,Rd [kNcm]

Internal Forces NEd [kN] Vz,Ed [kN] My,Ed [kNcm]

23-Oct-24 OASIS - LANDING PLATFORM | 75-0001128-01 | 1465_S001_LANDING PLATFORM Page 14 | 24

5.5.3 Bolt Connections