Scribd Logo
Upload

Welcome to Scribd!

  • 4 views

    For Preparation Description

    Uploaded by

    Milo Bal

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    For Preparation Description

    Uploaded by

    Milo Bal
    4 views3 pages

    Original Title

    p2759 (1)

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    4 views3 pages

    For Preparation Description

    Uploaded by

    Milo Bal

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    DTC P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift

    Solenoid Valve SLU)

    for Preparation Click here

    DESCRIPTION
    The amount of current flow to the solenoid is controlled by the ECM. During the lock-up operation, if the current increases, the lock-up
    hydraulic pressure increases.

    DTC Code DTC Detection Condition Trouble Area


    Open or short in shift solenoid valve SLU
    Open or short is detected in the shift solenoid valve circuit
    P2759 SLU circuit for 1 second or more while driving (1-trip Shift solenoid valve SLU
    detection logic). ECM

    MONITOR DESCRIPTION
    When an open or short in the shift solenoid valve SLU circuit is detected, the ECM determines that there is a malfunction. The ECM will
    illuminate the MIL and store the DTC.

    WIRING DIAGRAM
    INSPECTION PROCEDURE
    1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)

    a. Disconnect the C24 transmission wire connector.

    b. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Specified
    Tester Connection Condition
    Condition
    17 (SLU+) - 6
    20°C (68°F) 5.0 to 5.6 Ω
    (SLU-)
    17 (SLU+) - Body
    Always 10 kΩ or higher
    ground
    6 (SLU-) - Body
    Always 10 kΩ or higher
    ground

    Text in Illustration
    Component without harness connected
    *a
    (Transmission Wire)

    NG Go to step 3

    OK

    2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

    a. Disconnect the C29 ECM connector.

    b. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Specified
    Tester Connection Condition
    Condition
    C29-33 (SLU+) -
    20°C (68°F) 5.0 to 5.6 Ω
    C29-32 (SLU-)
    C29-33 (SLU+) -
    Always 10 kΩ or higher
    Body ground
    C29-32 (SLU-) -
    Always 10 kΩ or higher
    Body ground

    Text in Illustration
    Front view of wire harness connector
    *a
    (to ECM)

    NG REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE ECM (Click here)

    3.INSPECT SHIFT SOLENOID VALVE SLU

    a. Remove shift solenoid valve SLU.

    b. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Specified
    Tester Connection Condition
    Condition
    1-2 20°C (68°F) 5.0 to 5.6 Ω

    c. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and
    makes an operating noise.

    OK:
    Measurement Condition Specified Condition
    Battery positive
    (+) with a 21 W
    bulb → Terminal Valve moves and makes an
    2 operating noise
    Battery negative
    (-) → Terminal 1
    Text in Illustration
    Component without harness connected
    *a
    (Shift Solenoid Valve SLU)

    NG REPLACE SHIFT SOLENOID VALVE SLU (Click here)

    OK

    REPAIR OR REPLACE TRANSMISSION WIRE (Click here)

    You might also like