1195 Fa

Download as pdf or txt
Download as pdf or txt
You are on page 1of 12

LT1195

Low Power, High Speed


Operational Amplifier

U
FEATURES DESCRIPTIO
■ Gain-Bandwidth Product: 50MHz The LT®1195 is a video operational amplifier optimized for
■ Unity-Gain Stable operation on single 5V and ±5V supplies. Unlike many
■ Slew Rate: 165V/µs high speed amplifiers, the LT1195 features high open-
■ Output Current: ±20mA loop gain, over 75dB, and the ability to drive heavy loads
■ Low Supply Current: 12mA to a full power bandwidth of 8.5 MHz at 6VP-P. The LT1195
■ High Open-Loop Gain: 7.5V/mV has a unity-gain stable bandwidth of 50MHz, a 60° phase
■ Low Cost margin and consumes only 12mA of supply current,
■ Single Supply 5V Operation making it extremely easy to use.
■ Industry Standard Pinout Because the LT1195 is a true operational amplifier, it is an
■ Output Shutdown
ideal choice for wideband signal conditioning, fast
U integrators, peak detectors, active filters, and applications
APPLICATIO S requiring speed, accuracy, and low cost.
■ Video Cable Drivers The LT1195 is a low power version of the popular LT1190,
■ Video Signal Processing and is available in 8-pin miniDIPs and SO packages with
■ Fast Peak Detectors standard pinouts. The normally unused Pin 5 is used for a
■ Fast Integrators shutdown feature that shuts off the output and reduces
■ Video Cable Drivers power dissipation to a mere 15mW.
■ Pulse Amplifiers , LTC and LT are registered trademarks of Linear Technology Corporation

U
TYPICAL APPLICATIO
Fast Pulse Detector Pulse Detector Response

5V
RI
1k 3 D1
7
+ 1N5712
VIN RS CI 6
60pF LT1195
50Ω
2 OUTPUT
– 4
RL CL
10k 1000pF
–5V
–5V
RB D2
10k 1N5712

–5V 1195 TA01 INPUT

1195TAO2

1195fa

1
LT1195
W W W U U W U
ABSOLUTE AXI U RATI GS PACKAGE/ORDER I FOR ATIO
(Note 1) TOP VIEW ORDER PART
Total Supply Voltage (V+ to V – ) ............................... 18V NUMBER
BAL 1 8 BAL
Differential Input Voltage ......................................... ±6V –IN 2 V+
7
Input Voltage ........................................................... ±VS LT1195CN8
+IN 3 OUT
Output Short-Circuit Duration (Note 2) ......... Continuous
6 LT1195CS8
V– 4 5 S/D
Operating Temperature Range S8 PART MARKING
N8 PACKAGE S8 PACKAGE
LT1195M (OBSOLETE) ................... –55°C to 125°C 8-LEAD PDIP 8-LEAD PLASTIC SO
1195
LT1195C ................................................ 0°C to 70°C TJMAX = 150°C, θJA = 100°C/ W (N8)
TJMAX = 150°C, θJA = 150°C/ W (S8)
Junction Temperature (Note 3) ORDER PART
Plastic Package (CN8, CS8) ............................ 150°C NUMBER
J8 PACKAGE
Ceramic Package (CJ8, MJ8) (OBSOLETE) ..... 175°C 8-LEAD CERDIP LT1195MJ8
Storage Temperature Range ................. –65°C to 150°C TJMAX = 150°C, θJA = 100°C/ W (J8) LT1195CJ8
Lead Temperature (Soldering, 10 sec).................. 300°C OBSOLETE PACKAGE
Consider the N8 or S8 Package for Alternate Source

Consult LTC Marketing for parts specified with wider operating temperature ranges.

+
– 5V ELECTRICAL CHARACTERISTICS TA = 25°C
V = ±5V, C ≤ 10pF, Pin 5 open circuit, unless otherwise noted.
S L

LT1195M/C
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VOS Input Offset Voltage J8, N8 Package 3.0 8.0 mV
S8 Package 3.0 10.0 mV
IOS Input Offset Current 0.2 1.0 µA
IB Input Bias Current ±0.5 ±2.0 µA
en Input Noise Voltage fO = 10kHz 70 nV√Hz
in Input Noise Current fO = 10kHz 2 pA√Hz
RIN Input Resistance Differential Mode 230 kΩ
Common Mode 20 MΩ
CIN Input Capacitance AV = 1 2.2 pF
Input Voltage Range (Note 4) –2.5 3.5 V
CMRR Common Mode Rejection Ratio VCM = –2.5 to 3.5V 60 85 dB
PSRR Power Supply Rejection Ratio VS = ±2.375V to ±8V 60 85 dB
AVOL Large-Signal Voltage Gain RL = 1k, VOUT = ±3V 2.0 7.5 V/mV
RL = 150Ω, VOUT = ±3V 0.5 1.5 V/mV
VS = ±8V, RL = 1k, VOUT = ±5V 11.0 V/mV
VOUT Output Voltage Swing VS = ±5V, RL = 1k ±3.8 ±4.0 V
VS = ±8V, RL = 1k ±6.7 ±7.0 V
SR Slew Rate AV = –1, RL = 1k (Note 5, 10) 110 165 V/µs
FPBW Full Power Bandwidth VOUT = 6VP-P (Note 6) 8.75 MHz
GBW Gain-Bandwidth Product 50 MHz
tr1, tf1 Rise Time, Fall Time AV = 50, VOUT = ±1.5V, 20% to 80% (Note 10) 125 170 285 ns
tr2, tf2 Rise Time, Fall Time AV = 1, VOUT = ±125mV, 10% to 90% 3.4 ns
tPD Propagation Delay AV = 1, VOUT = ±125mV, 50% to 50% 2.5 ns
Overshoot AV = 1, VOUT = ±125mV 22 %
tS Settling Time 3V Step, 0.1% (Note 7) 220 ns
Diff AV Differential Gain RL = 150Ω, AV = 2 (Note 8) 1.25 %
Diff Ph Differential Phase RL = 150Ω, AV = 2 (Note 8) 0.86 DEGP-P
1195fa

2
LT1195
+
– 5V ELECTRICAL CHARACTERISTICS TA = 25°C
VS = ±5V, CL ≤ 10pF, Pin 5 open circuit, unless otherwise noted.
LT1195M/C
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
IS Supply Current 12 16 mA
Shutdown Supply Current Pin 5 at V – 0.8 1.5 mA
IS/D Shutdown Pin Current Pin 5 at V – 5 25 µA
tON Turn-On Time Pin 5 from V – to Ground, RL = 1k 160 ns
tOFF Turn-Off Time Pin 5 from Ground to V –, RL = 1k 700 ns

5V ELECTRICAL CHARACTERISTICS TA = 25°C


+ –
VS = 5V, VS , = OV, VCM = 2.5V, CL ≤ 10pF, Pin 5 open circuit, unless otherwise noted.
LT1195M/C
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VOS Input Offset Voltage J8, N8 Package 3.0 9.0 mV
S8 Package 3.0 11.0 mV
IOS Input Offset Current 0.2 1.0 µA
IB Input Bias Current ±0.5 ±2.0 µA
Input Voltage Range (Note 4) 2.0 3.5 V
CMRR Common Mode Rejection Ratio VCM = 2V to 3.5V 60 85 dB
AVOL Large-Signal Voltage Gain RL = 150Ω to Ground, VOUT = 1V to 3V 0.5 3.0 V/mV
VOUT Output Voltage Swing RL = 150Ω to Ground VOUT High 3.5 3.8 V
VOUT Low 0.25 0.4 V
SR Slew Rate AV = –1, VOUT = 1V to 3V 140 V/µs
GBW Gain-Bandwidth Product 45 MHz
IS Supply Current 11 15 mA
Shutdown Supply Current Pin 5 at V – 0.8 1.5 mA
IS/D Shutdown Pin Current Pin 5 at V – 5 25 µA

+
– 5V ELECTRICAL CHARACTERISTICS –55°C ≤ TA ≤ 125°C, (Note 11)
VS = ±5V, Pin 5 open circuit, unless otherwise noted.
LT1195M
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VOS Input Offset Voltage 3.0 15.0 mV
∆VOS /∆T Input VOS Drift 17 µV/°C
IOS Input Offset Current 0.2 2.0 µA
IB Input Bias Current ±0.5 ±2.5 µA
CMRR Common Mode Rejection Ratio VCM = –2.5V to 3.5V 55 85 dB
PSRR Power Supply Rejection Ratio VS = ±2.375V to ±8V 55 80 dB
AVOL Large-Signal Voltage Gain RL = 1k, VOUT = ±3V 1.50 5.0 V/mV
RL = 150Ω, VOUT = ±3V 0.25 0.8 V/mV
VOUT Output Voltage Swing RL = 1k ±3.7 ±3.9 V
IS Supply Current 12 18 mA
Shutdown Supply Current Pin 5 at V –, (Note 9) 0.8 2.5 mA
IS/D Shutdown Pin Current Pin 5 at V – 5 25 µA

1195fa

3
LT1195
+
– 5V ELECTRICAL CHARACTERISTICS 0°C ≤ TA ≤ 70°C
VS = ±5V, Pin 5 open circuit, unless otherwise noted.
LT1195C
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VOS Input Offset Voltage J8, N8 Package 3.0 10.0 mV
S8 Package 3.0 15.0 mV
∆VOS /∆T Input VOS Drift 12 µV/°C
IOS Input Offset Current 0.2 1.7 µA
IB Input Bias Current ±0.5 ±2.5 µA
CMRR Common Mode Rejection Ratio VCM = –2.5V to 3.5V 60 85 dB
PSRR Power Supply Rejection Ratio VS = ±2.375V to ±5V 60 90 dB
AVOL Large-Signal Voltage Gain RL = 1k, VOUT = ±3V 2.0 7.5 V/mV
RL = 150Ω, VOUT = ±3V 0.3 1.5 V/mV
VOUT Output Voltage Swing RL = 1k ±3.7 ±3.9 V
IS Supply Current 12 17 mA
Shutdown Supply Current Pin 5 at V – (Note 9) 0.9 2.0 mA
IS/D Shutdown Pin Current Pin 5 at V – 5 25 µA

5V ELECTRICAL CHARACTERISTICS 0°C ≤ TA ≤ 70°C


VS+ = 5V, VS– = OV, Pin 5 open circuit, unless otherwise noted.
LT1195C
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VOS Input Offset Voltage J8, N8 Package 1.0 10.0 mV
S8 Package 1.0 15.0 mV
∆VOS /∆T Input VOS Drift 15 µV/°C
IOS Input Offset Current 0.2 1.7 µA
IB Input Bias Current ±0.5 ±2.5 µA
Input Voltage Range (Note 4) 2.0 3.5 V
CMRR Common Mode Rejection Ratio VCM = 2V to 3.5V 60 85 dB
VOUT Output Voltage Swing RL = 150Ω to Ground VOUT High 3.5 3.75 V
VOUT Low 0.15 0.4 V
IS Supply Current 12 16 mA
Shutdown Supply Current Pin 5 at V – (Note 9) 0.9 2.0 mA
IS/D Shutdown Pin Current Pin 5 at V – 5 25 µA

Note 1: Absolute Maximum Ratings are those values beyond which the life Note 6: Full power bandwidth is calculated from the slew rate
of a device may be impaired. measurement: FPBW = SR/2πVP.
Note 2: A heat sink may be required to keep the junction temperature Note 7: Settling time measurement techniques are shown in “Take the
below absolute maximum when the output is shorted continuously. Guesswork Out of Settling Time Measurements,” EDN, September 19, 1985.
Note 3: TJ is calculated from the ambient temperature TA and power Note 8: NTSC (3.58MHz). For RL = 1k, Diff AV = 0.3%, Diff Ph = 0.35°.
dissipation PD according to the following formats: Note 9: See Applications Information section for shutdown at elevated
LT1195MJ8/LT1195CJ8: TJ = TA + (PD • 100°C/ W) temperatures. Do not operate the shutdown above TJ > 125°C.
LT1195N: TJ = TA + (PD • 100°C/ W) Note 10: AC parameters are 100% tested on the ceramic and plastic DIP
LT1195CS: TJ = TA + (PD • 150°C/ W) packaged parts (J8 and N8 suffix) and are sample tested on every lot of
Note 4: Exceeding the input common mode range may cause the output the SO packaged parts (S8 suffix).
to invert. Note 11: Do not operate at AV < 2 for TA < 0°C.
Note 5: Slew rate is measured between ±1V on the output, with ±3V input
step.

1195fa

4
LT1195
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Input Bias Current vs Input Bias Current vs Common Mode Voltage vs
Common Mode Voltage Temperature Temperature
3.0 100 V+
VS = ±5V VS = ±5V
–0.5
2.5 +IB
0 –1.0 V + = 1.8V TO 9V

COMMON MODE RANGE (V)


INPUT BIAS CURRENT (µA)

INPUT BIAS CURRENT (nA)


2.0 –1.5
–100 –2.0
1.5
–IB

1.0 –55°C –200 2.0


IOS 1.5
0.5
25°C V + = –1.8V TO –9V
–300 1.0
0
125°C 0.5
–0.5 –400 V–
–5 –4 –3 –2 –1 0 1 2 3 4 5 –50 –25 0 25 50 75 100 125 –50 –25 0 25 50 75 100 125
COMMON MODE VOLTAGE (V) TEMPERATURE (°C) TEMPERATURE (°C)
1195 G01 1195 G02 1195 G03

Equivalent Input Noise Voltage Equivalent Input Noise Current


vs Frequency vs Frequency Supply Current vs Supply Voltage
600 14 16
EQUIVALENT INPUT NOISE CURRENT (pA/√Hz)
EQUIVALENT INPUT NOISE VOLTAGE (nV/√Hz)

VS = ±5V VS = ±5V
TA = 25°C TA = 25°C
500 RS = 0Ω 12 RS = 100k –55°C
14

SUPPLY CURRENT (mA)


400 10
25°C

300 8 12
125°C
200 6
10
100 4

0 2 8
10 100 1k 10k 100k 10 100 1k 10k 100k 0 2 4 6 8 10
FREQUENCY (Hz) FREQUENCY (Hz) ±SUPPLY VOLTAGE (V)
1195 G04 1195 G05
1195 G06

Shutdown Supply Current Output Voltage Swing vs


vs Temperature Load Resistance Open-Loop Gain vs Temperature
6 5 10k
VS = ±5V VS = ±5V TA = –55°C VS = ±5V
VS/D = –VEE + 0.6V
SHUTDOWN SUPPLY CURRENT (mA)

VO = ±3V RL = 1k
5
OUTPUT VOLTAGE SWING (V)

3 8k
TA = 25°C
OPEN-LOOP GAIN (V/V)

4 TA = 125°C
VS/D = –VEE + 0.4V
1 6k
3 VS/D = –VEE + 0.2V

–1 4k
2
TA = 25°C
–3 2k
1 TA = 125°C TA = –55°C RL = 150Ω
VS/D = –VEE
0 –5 0
–50 –25 0 25 50 75 100 125 10 100 1k –50 –25 0 25 50 75 100 125
TEMPERATURE (°C) LOAD RESISTANCE (Ω) TEMPERATURE (°C)
1195 G07 1195 G08
1195 G09

1195fa

5
LT1195
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Open-Loop Voltage Gain vs Gain-Bandwidth Product vs
Gain and Phase vs Frequency Load Resistance Supply Voltage
100 100 20k 60
PHASE VS = ±5V AV = 20dB TA = –55°C
VO = ±3V

GAIN-BANDWIDTH PRODUCT (MHz)


OPEN-LOOP VOLTAGE GAIN (V/V)
80 80
16k TA = 25°C TA = 25°C
50

PHASE MARGIN (DEG)


VOLTAGE GAIN (dB)

60 60 TA = 125°C
12k
40 40 40
GAIN
8k
20 20
30
VS = ±5V 4k
0 0
TA = 25°C
RL = 1k
–20 –20 0 20
100k 1M 10M 100M 100 1k 10k 0 2 4 6 8 10
FREQUENCY (Hz) LOAD RESISTANCE (Ω) ±SUPPLY VOLTAGE (V)
1195 G10 1195 G11 1195 G12

Unity-Gain Frequency and Phase Common Mode Rejection Ratio


Margin vs Temperature Output Impedance vs Frequency vs Frequency
100 90 100 60
UNITY-GAIN VS = ±5V VS = ±5V VS = ±5V

COMMON MODE REJECTION RATIO (dB)


90 FREQUENCY RL = 1k 80 TA = 25°C TA = 25°C
50
UNITY-GAIN FREQUENCY (MHz)

RL = 1k
OUTPUT IMPEDANCE (Ω)

10
PHASE MARGIN (DEG)

80 70
UNITY-GAIN 40
AV = 10
PHASE MARGIN
70 60
1 30
60 50
AV = 1
20
50 40
0.1

40 30 10

30 20 0.01 0
–50 –25 0 25 50 75 100 125 1k 10k 100k 1M 10M 100M 100k 1M 10M 100M
TEMPERATURE (°C) FREQUENCY (Hz) FREQUENCY (Hz)
1195 G13 1195 G14 1195 G15

Power Supply Rejection Ratio Output Short-Circuit Current


vs Frequency vs Temperature ±Output Swing vs Supply Voltage
V+
80 36 –0.7
VS = ±5V VS = ±5V
OUTPUT SHORT-CIRCUIT CURRENT (mA)
POWER SUPPLY REJECTION RATIO (dB)

TA = 25°C –0.8
OUTPUT SATURATION VOLTAGE (V)

35 125°C
60 VRIPPLE = ±300mV
–0.9
25°C
34 –1.0
40 +PSRR –55°C
–PSRR –1.1
33 RL = RFB
0.5 ±1.8V ≤ VS ≤ ±9V 125°C
20
32 0.4 25°C

0 0.3
31
0.2 –55°C

–20 30 0.1
1k 10k 100k 1M 10M 100M –50 –25 0 25 50 75 100 125 V– 0 2 4 6 8 10
FREQUENCY (Hz) TEMPERATURE (°C) SUPPLY VOLTAGE (V)
1195 G16 1195 G17 1195 G18

1195fa

6
LT1195
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Output Voltage Step vs Output Voltage Step vs
Slew Rate vs Temperature Settling Time, AV = –1 Settling Time, AV = 1
250 4 4
VS = ±5V VS = ±5V VS = ±5V
RFB = 1k TA = 25°C TA = 25°C
VO = ±2V RL = 1k RL = 1k

OUTPUT VOLTAGE STEP (V)

OUTPUT VOLTAGE STEP (V)


AV = –1 2 2
10mV 1mV 10mV 1mV
SLEW RATE (V/µs)

–SLEW RATE
200 0 0

10mV 1mV
–2 –2
+SLEW RATE 10mV 1mV

150 –4 –4
–50 –25 0 25 50 75 100 125 0 100 200 300 400 0 100 200 300 400
TEMPERATURE (°C) SETTLING TIME (ns) SETTLING TIME (ns)
1195 G19 1195 G20 1195 G21

Large-Signal Transient Response Large-Signal Transient Response

AV = 1, RL = 1k AV = –1, RL = 1k
1195 G22 1195 G23

Overload Recovery

5V

3 7
+
6
LT1195
2 4
– 8
1

INPUT OFFSET VOLTAGE CAN BE ADJUSTED OVER A


±150mV RANGE WITH A 1k to 10k POTENTIOMETER.
1195 G25

AV = 1, VIN = 11VP-P
1195 G24

1195fa

7
LT1195
U U W U
APPLICATIO S I FOR ATIO
Power Supply Bypassing
The LT1195 is quite tolerant of power supply bypassing. receiving end (75Ω to ground) to absorb unwanted en-
In some applications a 0.1µF ceramic disc capacitor ergy. The best performance can be obtained by double
placed 0.5 inches from the ampifier is all that is required. termination (75Ω in series with the output of the amplifier,
In applications requiring good settling time, it is important and 75Ω to ground at the other end of the cable). This
to use multiple bypass capacitors. A 0.1µF ceramic disc in termination is preferred because reflected energy is ab-
parallel with a 4.7µF tantalum is recommended. sorbed at each end of the cable. When using the double
termination technique it is important to note that the signal
Cable Terminations is attenuated by a factor of 2, or 6dB. This can be compen-
The LT1195 operational amplifier has been optimized as a sated for by taking a gain of 2, or 6dB in the amplifier.
low cost video cable driver. The ±20mA guaranteed output
Using the Shutdown Feature
current enables the LT1195 to easily deliver 6VP-P into
150Ω, while operating on ±5V supplies. The LT1195 has a unique feature that allows the amplifier
to be shut down for conserving power, or for multiplexing
several amplifiers onto a common cable. The amplifier will
Double-Terminated Cable Driver shutdown by taking Pin 5 to V –. In shutdown, the amplifier
5V dissipates 15mW while maintaining a true high impedance
3
+ 7 output state of 15k in parallel with the feedback resistors.
CABLE
LT1195
6 75Ω The amplifiers must be used in a noninverting configura-
2
– tion for MUX applications. In inverting configurations the
4
RFB 75Ω input signal is fed to the output through the feedback
RG –5V
components. The following scope photos show that with
very high RL, the output is truly high impedance; the
1195 AI01
output slowly decays toward ground. Additionally, when
the output is loaded with as little as 1k the amplifier shuts
Cable Driver Voltage Gain vs Frequency off in 700ns. This shutoff can be under the control of HC
8 CMOS operating between 0V and –5V.
6
4 AV = 2
2 RFB = 1k
VOLTAGE GAIN (dB)

RG = 330Ω Output Shutdown


0
AV = 1
–2 RFB = 1k
–4 RG = 1k

–6
–8
VS = ±5V
–10 TA = 25°C
–12
100k 1M 10M 100M
FREQUENCY (Hz)
1195 AI02

When driving a cable it is important to terminate the cable


to avoid unwanted reflections. This can be done in one of
two ways: single termination or double termination. With 1MHz SINE WAVE GATED OFF WITH SHUTDOWN PIN
single termination, the cable must be terminated at the AV = 1, RL = SCOPE PROBE
1195 AI03

1195fa

8
LT1195
U U W U
APPLICATIO S I FOR ATIO
Output Shutdown Single 5V Video Amplifier
VIN

10µF
5V 5V
1k 3 7
+ 1000µF
6 75Ω
LT1195
2
R1 – 4 RFB
3k RG 1k 10k 75Ω
1k

100µF R2 1195 AI05

2k

1MHz SINE WAVE GATED OFF WITH SHUTDOWN PIN


AV = 1, RL = 1k
1195 AI04
Video Multiburst at Pin 6 of Amplifier

Detecting Pulses
The front page shows a circuit for detecting very fast
3V
pulses. In this open-loop design, the detector diode is D1
and a level shifting or compensating diode is D2. A load
resistor RL is connected to –5V, and an identical bias 2V
resistor RB is used to bias the compensating diode. Equal
value resistors ensure that the diode drops are equal. A
1V
very fast pulse will exceed the amplifier slew rate and
cause a long overload recovery time. Some amount of
dV/dt limiting on the input can help this overload condi- 0V
tion, however too much will delay the response. Also 1195 AI06

shown is the response to a 4VP-P input that is 150ns wide.


The maximum output slew rate in the photo is 30V/µs. This
rate is set by the 30mA current limit driving 1000pF. Vector Plot of Standard Color Burst

Operation on Single 5V Supply


The LT1195 has been optimized for a single 5V supply.
This circuit amplifies standard composite video (1VP-P
including sync) by 2 and drives a double-terminated 75Ω
cable. Resistors R1 and R2 bias the amplifier at 2V,
allowing the sync pulses to stay within the common mode
range of the amplifier. Large coupling capacitors are
required to pass the low frequency sidebands of the
composite signal. A multiburst response and vector plot
standard color burst are shown.
1195 AI07

1195fa

9
LT1195
U U W U
APPLICATIO S I FOR ATIO
Send Color Video Over Twisted-Pair 1.5MHz Square Wave Input and Equalized
Response Through 1000 Feet of Twisted-Pair
With an LT1195 it is possible to send and receive color
composite video signals more than 1000 feet on a low cost
twisted-pair. A bidirectional “video bus” consists of the
LT1195 op amp and the LT1187 video difference amplifier.
A pair of LT1195s at TRANSMIT 1, is used to generate
differential signals to drive the line which is back-termi-
nated in its characteristic impedance. The LT1187
twisted-pair receiver, converts signals from differential to
single-ended. Topology of the LT1187 provides for cable
compensation at the amplifier’s feedback node as shown.
In this case, 1000 feet of twisted-pair is compensated with
1000pF and 50Ω to boost the 3dB bandwidth of the 1195 A109

system from 750kHz to 4MHz. This bandwidth is adequate


to pass a 3.58MHz chrome subcarrier and the 4.5MHz
sound subcarrier. Attenuation in the cable can be compen- Multiburst Pattern Passed Through
1000 Feet of Twisted-Pair
sated by lowering the gain set resistor RG. At TRANSMIT
2, another pair of LT1195s serve the dual function to
provide cable termination via low output impedance and
generate differential signals for TRANSMIT 2. Cable termi-
nation is made up of 15Ω and 33Ω attentuators to reduce
the differential input signal to the LT1187. Maximum input
signal for the LT1187 is 760mVP-P.

1.5MHz Square Wave Input and Unequalized


Response Through 1000 Feet of Twisted-Pair

1195 A110

Vector Plot of Standard Color Burst Through


1000 Feet of Twisted-Pair

1195 A108

1195 A111

1195fa

10
LT1195
U U W U
APPLICATIO S I FOR ATIO
Bidirectional Video Bus
TRANSMIT 1 TRANSMIT 2

3 3
+ +
6 6
75Ω 1k LT1195 LT1195 1k 75Ω
2 2
– –
1k 1k
1k 1k
1k 1k

2 2
– –
6 6
LT1195 LT1195
3 3
+ 33Ω 33Ω 33Ω 33Ω +
S/D 1000 FT S/D
3 15Ω TWISTED-PAIR 15Ω 3
5 + + 5
2 15Ω 15Ω 2
75Ω 6 – – 6 75Ω
LT1187 1 1 LT1187
+ +
8 8
RFB – – RFB
300Ω 300Ω

1000pF 1000pF
RG
50Ω 50Ω RG
300Ω
300Ω

RECEIVE 2 RECEIVE 1 1195 AI12

W W
SIWPLIFIED SCHEWATIC
7 V+
VBIAS VBIAS
CM

+ 3
CFF
– 2
V+ V+ 6 VOUT

4 V–

5 1 8
S/D BAL BAL
1195 SS

* SUBSTRATE DIODE, DO NOT FORWARD BIAS

1195fa

11
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
LT1195
U
PACKAGE DESCRIPTIO
J8 Package
8-Lead CERDIP (Narrow .300 Inch, Hermetic)
(Reference LTC DWG # 05-08-1110) .405
(10.287)
.200 .005 MAX
.300 BSC CORNER LEADS OPTION (5.080) (0.127)
(7.62 BSC) (4 PLCS) MAX MIN
8 7 6 5

.015 – .060
.023 – .045 (0.381 – 1.524)
.025 .220 – .310
(0.584 – 1.143)
(0.635) (5.588 – 7.874)
HALF LEAD
RAD TYP
.008 – .018 OPTION
0° – 15°
(0.203 – 0.457) .045 – .068
(1.143 – 1.650) 1 2 3 4
FULL LEAD .045 – .065
OPTION .125
(1.143 – 1.651)
3.175
NOTE: LEAD DIMENSIONS APPLY TO SOLDER MIN
DIP/PLATE OR TIN PLATE LEADS .014 – .026 .100
(0.360 – 0.660) (2.54) J8 0801
BSC

OBSOLETE PACKAGE

N8 Package
8-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
.300 – .325 .045 – .065 .130 ± .005 .400*
(7.620 – 8.255) (1.143 – 1.651) (3.302 ± 0.127) (10.160)
MAX

8 7 6 5
.065
(1.651)
.009 – .015 TYP
.125 .255 ± .015*
(0.229 – 0.381)
(3.175) .020 (6.477 ± 0.381)
+.035 MIN (0.508)
.325 –.015
.100 .018 ± .003 MIN

( 8.255
+0.889
–0.381 ) (2.54)
BSC
(0.457 ± 0.076)
N8 0502
1 2 3 4

NOTE:
INCHES
1. DIMENSIONS ARE
MILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)

S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.045 ±.005 .189 – .197
.050 BSC (4.801 – 5.004)
NOTE 3
N 8 7 6 5

.245 N
MIN .160 ±.005

.150 – .157
.228 – .244
(3.810 – 3.988)
1 2 3 N/2 (5.791 – 6.197)
NOTE 3
N/2
.030 ±.005
TYP RECOMMENDED SOLDER PAD LAYOUT
NOTE:
INCHES
1. DIMENSIONS IN
(MILLIMETERS) 1 2 3 4
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE .053 – .069
MOLD FLASH OR PROTRUSIONS. .010 – .020 (1.346 – 1.752)
MOLD FLASH OR PROTRUSIONS SHALL × 45° .004 – .010
(0.254 – 0.508)
NOT EXCEED .006" (0.15mm) (0.101 – 0.254)
.008 – .010
(0.203 – 0.254) 0°– 8° TYP

.014 – .019 .050


.016 – .050 (0.355 – 0.483) (1.270)
(0.406 – 1.270) TYP BSC SO8 0502

1195fa

LW/TP 1002 1K REV A • PRINTED IN USA


Linear Technology Corporation
12 1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507 ●
www.linear.com  LINEAR TECHNOLOGY CORPORATION 1993

You might also like