Scribd
Upload
27 views6 pages

3 Multiple Roughing and Pocketing

Uploaded by

ahmetet2yy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
27 views6 pages

3 Multiple Roughing and Pocketing

Uploaded by

ahmetet2yy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Create the stock for the part

-Select AUTOMATIC STOCK


-Select a SHAPE of [BOX]
-For this activity we will leave all the stock box offsets
at ZERO

Evaluate and redefine the part reference zero PRZ or


CPL

-For this example, the PRZ should not need to be reset.


It has been created in Autodesk Inventor with the
correct PRZ as we would like to assign it.

Nothing needs to be done at this step.


Use the feature finder to allow EdgeCAM to evaluate
the 3D CAD model in order to break the model into
manufacturable features

Hole Options
Find Vertical
CAD Link Information
Match to Template
Group Similar Holes
Maximum Diameter = The largest tool you have to be
able to drill with (Example = 0.25)

Mill Options
2D Pocket
2D Boss

All features found will now


be displayed on the features
tab

Leave DESIGN mode and enter MANUFACTURE mode

DISCIPLINE – [Mill]

MACHINE TOOL – Choose the correct POST for your


machine [intelitek.mcp]

INITIAL CPL – Ensure the CPL is [Top]

Switch from the SEQUENCE tab back to the FEATURES


tab

-Select the 1st 2D Pocket from the features list.

Note: As you hover over the features, they should


highlight the corresponding feature on the 3D model.

Right click on the first 2D Pocket and select Roughing


Operation from the list

At this time we do not need to define any boundaries


for this operation. Select either select the check mark
in the top right corner, select
enter on the keyboard, or right
click to select DONE
GENERAL
-MILL TYPE – Either select [CLIMB]
-% STEPOVER – [50%]
-OFFSET – [0] (Used to leave material on all axis (X, Y
and Z). A finishing operation can then be used to
remove the offset material
-Z OFFSET – [0] (Used to leave material on only the Z
Plane of the surface defined. Also used along with the
offset to override the Z axis if a quantity is left from the
Offset line
-TOLERANCE – [0.001 to 0.005]

TOOLING
-1ST Choose the FIND box (choose the largest end mill
tool you have available in your library or have available
at you machine)
-2nd Ensure the FEEDRATE, PLUNGE RATE, and SPEED
are correct for the material and the tool you are using.

DEPTH
-CLEARANCE – [0.25] - Retract point above the PRZ
-LEVEL – [0] – Measured from the top of the feature
selected
-DEPTH – [0] - Measured from the bottom of the
feature selected
-CUT INCREMENT – [0.1875] - determine a safe number
for the tool you are using to go from the level to the
depth. If the Cut Increment is smaller than depth, the
facing operation will produce multiple passes to go
from the level to the depth.

For prototyping material, use approximately ½ to 1/3


the bit diameter as the cut increment
Simulate the machining process

Once the simulator opens, Select PLAY

Ensure the simulator produce the results desired

Select the COMPARE tool – this option will compare


the original 3D model and the results of the simulated
operations. At this time since we raised the stock
above the 3D model, set the facing operation to only
cut the amount raised from the 3D model, the
compare should show as all green

GREEN – Simulation and CAD model areas that Match


BLUE – Areas not removed or remaining from the stock
to produce the 3D model
RED – Areas removed from the stock that have cut into
the 3D model

Close the simulator to return to EdgeCAM

Switch from the SEQUENCE tab back to the FEATURES


tab

-Select the 2nd 2D Pocket from the features list.

Note: As you hover over the features, they should


highlight the corresponding feature on the 3D model.

Right click on the second 2D Pocket and select


Roughing Operation from the list

At this time we do not need to define any boundaries


for this operation. Select either select the check mark
in the top right corner, select
enter on the keyboard, or right
click to select DONE
GENERAL
All setting should be the same as the last setup

TOOLING
Select USE CURRENT TOOL to keep the same tool and
speeds and feeds as used in the previous operation

DEPTH
All setting should be the same as the last setup

Simulate the machining process

Once the simulator opens, Select PLAY

Ensure the simulator produce the results desired


Select the COMPARE tool – this option will compare
the original 3D model and the results of the simulated
operations. At this time since we raised the stock
above the 3D model, set the facing operation to only
cut the amount raised from the 3D model, the
compare should show as all green

GREEN – Simulation and CAD model areas that Match


BLUE – Areas not removed or remaining from the stock
to produce the 3D model
RED – Areas removed from the stock that have cut into
the 3D model

Close the simulator to return to EdgeCAM


*Note: If EdgeCAM is running in HOME WORK mode,
producing the NC code is not available

Select NC tool from the tool bar to produce the NC


code using the POST Processor selected earlier

You might also like