Scribd
Upload
38 views6 pages

Column

Uploaded by

viosglen69
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
38 views6 pages

Column

Uploaded by

viosglen69
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 6

Column Design (Consider only the most critical column and adopt all throughout)

1)Input Data
Unfactored axial load Pu 3675 KN
Unsupported length L 3.0 m
Grade of concrete fck 21 N/mm2 `
Grade of steel fy 415 N/mm 2

Restrained conditions 3 (Refer to sheet on "effective length")


K 1
effective length Le = 3m

2)Determine the size of the column


factored load 5512.5KN
Self wt. of column 55.125KN (1% of factored load on column)
Total Factored Load Pu 5567.625KN
pt 20% (Assume value between 0.8% to 4%)
Arequired 86980.5499 mm 2
Use, Pu = Ac(0.4*fck + 0.67*fy*pt) & Calculate Ac
Assume b 350mm 𝐴𝑐= 𝑃_𝑢/0.4𝑓_𝑐𝑘+0.67𝑓_𝑦 𝑝_𝑡
D 350mm
Aprovided 122500 mm2 OK

3)Check for slenderness ratio


Le/b 8.57
Le/D 8.57
HENCE DESIGN AS SHORT COLUMN

4) Estimate Longitudinal Reinforcement


Asc,required 16323.0534
Ast,min 980 mm2 OK
provide 4bars of 16mm dia. & 4bars of 16mm dia

Asc,prov. 205887.416 mm2 OK

𝐿/900+𝐷/30,12mm
5)Check for minimum eccentricity
ex,min 15mm OK emin = max. of :

𝑚𝑖𝑛. 𝑑𝑖𝑎= ∅_𝑝𝑟𝑜𝑣𝑖𝑑𝑒𝑑/4


ey,min 15.4166667mm OK
3
6)Design of lateral ties
dia. of ties φties 10 mmØ emin should be less than 0.05*D
and 0.05*b respectively
Pitch is taken smaller of the following:
a) LLD = 350mm
b) 16*φSL = 256mm
c) 200 mm 200mm 10mmØsp.2-05
2-.075,2-0.10
pitch provided = 200mm 2-0.25 rest at 0.20m
10mm @ 200 mm c/c
4-16 mmØ & 4-16 mmØ
Design Summary
b 350mm
D 350mm
Longitudinal bar details 4-16 mmØ & 4-16 mmØ 350

Asc,provided 205887.42 mm2


Dia. Of ties 10 mmØ
Pitch of ties 200mm
350 mm
Reinforcement details
TABLE: EFFECTIVE LENGTH OF COMPRESSION MEMBERS
CASE.NO. DEGREE OF END RESTRAINT OF COMPRESSION MEMBER
EFFECTIVELY HELD IN POSITION AND RESTRAINED AGAINST ROTATION AT BOTH ENDS

EFFECTIVELY HELD IN POSITION AT BOTH ENDS, RESTRAINED AGAINST ROTATION AT ONE END

EFFECTIVELY HELD IN POSITION AT BOTH ENDS, BUT NOT RESTRAINED AGAINST ROTATION

EFFECTIVELY HELD IN POSITION AND RESTRAINED AGAINST ROTATION AT ONE END, AND
AT THE OTHER RESTRAINED AGAINST ROTATION BUT NOT HELD IN POSITION

EFFECTIVELY HELD IN POSITION AND RESTRAINED AGAINST ROTATION AT ONE END, AND
AT THE OTHER PARTIALLY RESTRAINED AGAINST ROTATION BUT NOT HELD IN POSITION

EFFECTIVELY HELD IN POSITION AT ONE END BUT NOT RESTRAINED AGAINST ROTATION, AND
AT THE OTHER END RESTRAINED AGAINST ROTATION BUT NOT HELD IN POSITION

EFFECTIELY HELD IN POSITION AND RESTRAINED AGAINST ROTATION AT ONE END


BUT NOT HELD IN POSITION NOR RESTRAINED AGAINST ROTATION AT OTHER END

7
7
KTHEORECTICAL KACTUAL

0.5 0.65

0.7 0.8

1 1

1 1.2

N.A 1.5

2 2

2 2
2 2

You might also like