0% found this document useful (0 votes)

257 views64 pages

Structure Design Report 5H8@1000 - Purlin

Staad report and load calculation of 5H8

Uploaded by

SalauddinAnsari

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

257 views64 pages

Structure Design Report 5H8@1000 - Purlin

Staad report and load calculation of 5H8

Uploaded by

SalauddinAnsari

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 64

FIXED TILT STRUCTURE FOR PHOTOVOLTAIC PANELS

1.0MW ZAMIL - SOLAR GROUND MOUNT PROJECT,

RIYAD, SAUDI ARABIA
CUSTOMER: ZAMIL

Rev. Date Revision Details Originator Checked Approved

00 09/11/24 Issued for Approval SA AM PR

© Copyright ABMTG
This document is the property of Al-Babtain Metalogalva JV (ABMTG) and may contain confidential and proprietary information. It
may not be used for any purpose other than that for which it is supplied. This document may not be wholly or partly disclosed,
copied, duplicated or in any way made use of without prior written approval of ABMTG.
TABLE OF CONTENTS 1.0 INTRODUCTION 4
1.1 Project description 4
1.2 Document scope 4
1.3 Geometry 4
1.4 Structure Description 4
2.0 CALCULATION RESOURCES 6
2.1 Loads 6
2.2 Wind Loads 6
2.3 Snow Loads 6
2.4 Ultimate Limit States (U.L.S.) 6
2.5 Service Limit States (S.L.S.) 6
3.0 BASIS OF ANALYSIS 7
3.1 Introduction 7
3.2 Materials 7
3.2.1 Fabrication methods 7
4.0 CALCULATION REPORT 8
4.1 Sections 8
4.2 Materials 8
4.3 Loads 8
4.4 Load Combinations 8
4.5 Load Application 9
4.6 Reactions (Global Extremes) 9

Appendix A Dead loads calculations

Appendix B Wind loads calculations

Appendix C Calculations for Block size

Appendix D Application of load at structures

Appendix E Staad Input

Appendix F Staad Output

Appendix G Utilization Ratio Appendix H GA Drawing

1.0 INTRODUCTION

1.1 Project description

Al-Babtain Metalogalva JV have been invited by Zamil to do the analysis, design, manufacture &
supply ofFixed tilt structures supporting photovoltaic panels, as part of 1.0 MWp Solar PV Power
Plant in Riyadh, KSA.
1.2 Document scope

The scope of this document is to perform a structural assessment of fixed tilt structures. This
document covers modelling and analysis approach, design assumptions. The results include unity
check plot and deflection plots. Wind load calculation, general arrangement drawings & analysis
results are presented in Appendices.
1.3 Geometry

The structure is composed by photovoltaic fixed tilt structure with an inclination of 5◦ supported
on column separated by 1.40 m embedded in ground. The lower edge of the panel is 1.00m and
the higher edge 1.50m above top of ground level. The total number of panels installed in each
structure is 5 & arranged in 5 rows & 1 columns in vertical orientation. The dimensions of each
panel are 2382 × 1134 × 35 mm.
1.4 Structure Description

The structure will be made in steel grade S355. The panels will be fixed to the secondary beams
by clamps. The remaining connections are materialized by bolts (SS306). The Frames have the
geometry represented are spaced 1.40m.

Figure 1.1 Fixed tilt Structure– Side View

Figure 1.2 Fixed tilt Structure– Front View

Figure 1.3 Fixed tilt Structure with PV panels – Isometric View

2.0 CALCULATION RESOURCES

2.1 Loads
The loads are defined by the ASCE 7-16/SBC 301 and customer requirement.
Permanent Loads: self-weight and panels weight.
Variable Loads: wind loads and snow loads.

2.2 Wind Loads

Wind loading is derived from the customer specifications and rules given in SBC 301-CR-18 &
ASCE/SEI 7-16. The Basic wind speed (3-sec gust) considered is 160kmph (44.44 m/s). The
Exposure category considered is
C. The peak velocity pressure, qh will be 0.874 kN/m2.
The net pressure coefficients for pitched fixed tilt solar structures are calculated as per latest SBC
301-CR-18 & ASCE/SEI 7-16, Chapter 27-Figure 27.3-4. See Appendix A for detail wind loads
calculation.
2.3 Snow Loads

No snow loads are considered for the design (customer requirement).

2.4 Allowable Stress Design (ASD)

Allowable Stress Design (ASD) also known as Working Stress Design (WSD) method is based on
the principle that stresses developed in the structural members should not exceed a certain
fraction of elastic limit.
2.5 Load and Resistance Factor Design (LRFD)

Limit State Design (LSD), also known as Load and Resistance Factor Design (LRFD), refers to a
design method used in structural engineering. A limit state is a condition of a structure beyond
which it no longer fulfills the relevant design criteria.
2.6 Service Limit States (S.L.S.)

The service limit states were considered for the quasi-permanent combination and frequent

combination, which the respective beams vertical deformations were limited to L/240

3.0 BASIS OF ANALYSIS

3.1 Introduction
Stability verification, forces and displacements determination were calculated with STAAD Pro
structural analysis program for modelling the Ultimate Limit State.
3.2 Materials

The materials Material Standard

used for
fabrication of the
structure are:
Element
Steel Profiles & S355 EN 10025
plates
Bolts & Nuts SS304 EN4017

4.0 CALCULATION REPORT

4.1 Sections

Prop Name Area Iyy Izz J Material Source

(in2) (in4) (in4) (in4)

1 80CS50X2 0.598 0.320 0.963 0.001 STEEL Legacy

2 40LU40X3.15 0.358 0.087 0.087 0.002 STEEL Legacy

3 60CS60X2 0.598 0.447 0.577 0.001 STEEL Legacy

4.2 Material

Mat Name E  Density 

(kip/in2) (kip/in3) (/°F)

1 STEEL 29,000.000 0.300 0.000 0.000

4.3 Load Combination

L/C Type Name

1 Primary DL

2 Primary WL_UP Case A

3 Primary WL_UP Case B

4 Primary WL_DN Case A

5 Primary WL_DN Case B

6 Combination 1.4DL

7 Combination 1.2DL+WL_UP Case A

8 Combination 1.2DL+WL_UP Case B

9 Combination 1.2DL+WL_DN Case A

10 Combination 1.2DL+WL_DN Case B

11 Combination 0.9DL+WL_UP Case A

12 Combination 0.9DL+WL_UP Case B

13 Combination 0.9DL+WL_DN Case A

14 Combination 0.9DL+WL_DN Case B

15 Combination DL+WL_UP Case A

16 Combination DL+WL_UP Case B

17 Combination DL+WL_DN Case A

18 Combination DL+WL_DN Case B

19 Combination DL+0.6WL_UP Case A

20 Combination DL+0.6WL_UP Case B

21 Combination DL+0.6WL_DN Case A

22 Combination DL+0.6WL_DN Case B

Appendix A Dead loads calculations

CALCULATION OF DEAD LOAD

Solar module dimension Length Width HT
2.382 1.134 30
Weight per module 34 Kg
Numbers of module 40 No.
Weight of all module 1360 Kg 13.346 KN
Length of purlin 19.2 m
Number of Purlin 6 No.
Member load per unit length 0.116 KN/m
Appendix B Wind loads calculations

Panel Characteristics
Height a = 2382 mm
Width b = 1134 mm
Thickness d = 30 mm
Weight  = 34 kG
Distance of mounting slots to the edge c = 491 mm
Maximum power P = 580 wP
Self-weight of the panels p  = 0.123 kN/m2

Panels layout characteristics

Panels orientation Horizontal / Landscape
Type of panels disposition 2
No. of rows/structure i 5
No. of columns/structure j 8
Layout model 5H8
Internal clamps width Ci = 20 mm
Edge clamps width Ce = 45 mm
Distance between panels e = 20 mm
Extra length on the principal beams f = 90 mm
Secondary beams orientation Inclined
Secondary beams length Sb = 11098 mm
Principal beams length Pb = 9302 mm

Structure characteristics
Type of Structure/Table Monoslope
Obstruction under the Structure/Table Unobstructed
Table inclination with horizontal plane  = 5º deg
Panels Min. distance to the ground g = 500 mm
Panels Max.distance to the ground h = 1001 mm
Panels Mean distance to the ground z = 751 mm
Design working life (years) yrs = 25 Years
Load factor w = 1
Risk category of Building = I
Basic Wind Speed V = 44.44 m/s
Wind directionality factor Kd = 0.85
Exposure category = C
Topography factor Kzt = 1
Ground Elevation factor Ke = 1
Gust effect factor Gf = 0.85
Velocity pressure Exposure Coeff. Kz = 0.85
Velocity pressure qh = 874.85 N/m2
Net pressure Coefficients, CN & Net Coeffiecients Net design Pressure
design pressure, p CNW CNL pNW pNL
Load case A0 1.20 0.30 0.89 0.77 KN/m2
Wind direction,  = 0o
Load case B0 -1.10 -0.10 -0.82 -0.77 KN/m2
Load case A180 1.20 0.30 0.89 0.77 KN/m2
Wind direction,  = 180o
Load case B180 -1.10 -0.10 -0.82 -0.77 KN/m2
A90 -0.80 -0.77 KN/m2
For <h
B90 0.80 0.77 KN/m2
For >h, A90 -0.60 -0.77 KN/m2
Wind direction,  = 90o
<2h B90 0.50 0.77 KN/m2
A90 -0.30 -0.77 KN/m2
For >2h
B90 0.30 0.77 KN/m2

Panel Length m 2.382 Case A 0.837 0.722 KN/m2

y = 0°
Panel Width m 1.134 Case B -0.767 -0.72 KN/m2
No of solar panel nos 40 y= Case A 0.83694 0.722 KN/m2
Total area of solar Panels Sqm 108.05 180° Case B -0.7672 -0.72 KN/m2
Number of purlin nos 6
Lenth of Purlin m 19.2

Appendix C Calculations for Block size

Appendix D Application of load at structures
Appendix E Staad Input

1. STAAD SPACE
INPUT FILE: D:\ABMTG DESIGN\OneDrive - Al-Babtain Metalogalva
(ABL)\DESIGN\SOLAR RFQ's\Fixed Tilt 2024.. .STD
2. START JOB INFORMATION
3. ENGINEER DATE 31-OCT-24
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 0 0 0; 2 2.2 0 0; 3 4.40001 0 0; 4 0 0.700001 0; 5 2.2 0.895002 0
9. 6 4.40001 1.09 0; 7 0 0.305001 0; 8 4.40001 0.540001 0; 9 0.861624 0.776373 0
10. 10 3.54473 1.01419 0; 11 5.13712 1.15534 0; 12 -0.737112 0.634667 0
11. 27 0 0.575001 0; 31 4.40001 0.850001 0; 32 -0.677346 0.639964 0
12. 33 0.47215 0.741851 0; 34 1.62165 0.843739 0; 35 2.77076 0.945591 0
13. 36 3.92026 1.04748 0; 37 5.06939 1.14934 0; 38 0 0 3.00001; 39 2.2 0 3.00001
14. 40 4.40001 0 3.00001; 41 0 0.700001 3.00001; 42 2.2 0.895002 3.00001
15. 43 4.40001 1.09 3.00001; 44 0 0.305001 3.00001; 45 4.40001 0.540001 3.00001
16. 46 0.861624 0.776373 3.00001; 47 3.54473 1.01419 3.00001
17. 48 5.13712 1.15534 3.00001; 49 -0.737112 0.634667 3.00001
18. 50 0 0.575001 3.00001; 51 4.40001 0.850001 3.00001
19. 52 -0.677346 0.639964 3.00001; 53 0.47215 0.741851 3.00001
20. 54 1.62165 0.843739 3.00001; 55 2.77076 0.945591 3.00001
21. 56 3.92026 1.04748 3.00001; 57 5.06939 1.14934 3.00001; 58 0 0 6.00001
22. 59 2.2 0 6.00001; 60 4.40001 0 6.00001; 61 0 0.700001 6.00001
23. 62 2.2 0.895002 6.00001; 63 4.40001 1.09 6.00001; 64 0 0.305001 6.00001
24. 65 4.40001 0.540001 6.00001; 66 0.861624 0.776373 6.00001
25. 67 3.54473 1.01419 6.00001; 68 5.13712 1.15534 6.00001
26. 69 -0.737112 0.634667 6.00001; 70 0 0.575001 6.00001
27. 71 4.40001 0.850001 6.00001; 72 -0.677346 0.639964 6.00001
28. 73 0.47215 0.741851 6.00001; 74 1.62165 0.843739 6.00001
29. 75 2.77076 0.945591 6.00001; 76 3.92026 1.04748 6.00001
30. 77 5.06939 1.14934 6.00001; 78 0 0 9.00002; 79 2.2 0 9.00002
31. 80 4.40001 0 9.00002; 81 0 0.700001 9.00002; 82 2.2 0.895002 9.00002
32. 83 4.40001 1.09 9.00002; 84 0 0.305001 9.00002; 85 4.40001 0.540001 9.00002
33. 86 0.861624 0.776373 9.00002; 87 3.54473 1.01419 9.00002
34. 88 5.13712 1.15534 9.00002; 89 -0.737112 0.634667 9.00002
35. 90 0 0.575001 9.00002; 91 4.40001 0.850001 9.00002
36. 92 -0.677346 0.639964 9.00002; 93 0.47215 0.741851 9.00002
37. 94 1.62165 0.843739 9.00002; 95 2.77076 0.945591 9.00002
38. 96 3.92026 1.04748 9.00002; 97 5.06939 1.14934 9.00002; 98 0 0 12; 99 2.2 0 12
_ STAAD SPACE -- PAGE NO. 2

39. 100 4.40001 0 12; 101 0 0.700001 12; 102 2.2 0.895002 12; 103 4.40001 1.09 12
40. 104 0 0.305001 12; 105 4.40001 0.540001 12; 106 0.861624 0.776373 12
41. 107 3.54473 1.01419 12; 108 5.13712 1.15534 12; 109 -0.737112 0.634667 12
42. 110 0 0.575001 12; 111 4.40001 0.850001 12; 112 -0.677346 0.639964 12
43. 113 0.47215 0.741851 12; 114 1.62165 0.843739 12; 115 2.77076 0.945591 12
44. 116 3.92026 1.04748 12; 117 5.06939 1.14934 12; 118 0 0 15; 119 2.2 0 15
45. 120 4.40001 0 15; 121 0 0.700001 15; 122 2.2 0.895002 15; 123 4.40001 1.09 15
46. 124 0 0.305001 15; 125 4.40001 0.540001 15; 126 0.861624 0.776373 15
47. 127 3.54473 1.01419 15; 128 5.13712 1.15534 15; 129 -0.737112 0.634667 15
48. 130 0 0.575001 15; 131 4.40001 0.850001 15; 132 -0.677346 0.639964 15
49. 133 0.47215 0.741851 15; 134 1.62165 0.843739 15; 135 2.77076 0.945591 15
50. 136 3.92026 1.04748 15; 137 5.06939 1.14934 15; 138 0 0 18; 139 2.2 0 18
51. 140 4.40001 0 18; 141 0 0.700001 18; 142 2.2 0.895002 18; 143 4.40001 1.09 18
52. 144 0 0.305001 18; 145 4.40001 0.540001 18; 146 0.861624 0.776373 18
53. 147 3.54473 1.01419 18; 148 5.13712 1.15534 18; 149 -0.737112 0.634667 18
54. 150 0 0.575001 18; 151 4.40001 0.850001 18; 152 -0.677346 0.639964 18
55. 153 0.47215 0.741851 18; 154 1.62165 0.843739 18; 155 2.77076 0.945591 18
56. 156 3.92026 1.04748 18; 157 5.06939 1.14934 18
57. 158 -0.677346 0.639964 -0.600001; 159 0.47215 0.741851 -0.600001
58. 160 1.62165 0.843739 -0.600001; 161 2.77076 0.945591 -0.600001
59. 162 3.92026 1.04748 -0.600001; 163 5.06939 1.14934 -0.600001
60. 164 -0.677346 0.639964 18.6; 165 0.47215 0.741851 18.6
61. 166 1.62165 0.843739 18.6; 167 2.77076 0.945591 18.6; 168 3.92026 1.04748
18.6
62. 169 5.06939 1.14934 18.6
63. MEMBER INCIDENCES
64. 1 1 7; 2 2 5; 3 3 8; 4 4 33; 5 5 35; 6 7 27; 7 8 31; 8 9 34; 9 7 9; 10 10 36
65. 11 8 10; 12 6 37; 13 12 32; 29 27 4; 34 31 6; 35 32 4; 36 33 9; 37 34 5
66. 38 35 10; 39 36 6; 40 37 11; 41 38 44; 42 39 42; 43 40 45; 44 41 53; 45 42 55
67. 46 44 50; 47 45 51; 48 46 54; 49 44 46; 50 47 56; 51 45 47; 52 43 57; 53 49 52
68. 54 50 41; 55 51 43; 56 52 41; 57 53 46; 58 54 42; 59 55 47; 60 56 43; 61 57 48
69. 62 58 64; 63 59 62; 64 60 65; 65 61 73; 66 62 75; 67 64 70; 68 65 71; 69 66 74
70. 70 64 66; 71 67 76; 72 65 67; 73 63 77; 74 69 72; 75 70 61; 76 71 63; 77 72 61
71. 78 73 66; 79 74 62; 80 75 67; 81 76 63; 82 77 68; 83 78 84; 84 79 82; 85 80 85
72. 86 81 93; 87 82 95; 88 84 90; 89 85 91; 90 86 94; 91 84 86; 92 87 96; 93 85 87
73. 94 83 97; 95 89 92; 96 90 81; 97 91 83; 98 92 81; 99 93 86; 100 94 82
74. 101 95 87; 102 96 83; 103 97 88; 104 98 104; 105 99 102; 106 100 105
75. 107 101 113; 108 102 115; 109 104 110; 110 105 111; 111 106 114; 112 104 106
76. 113 107 116; 114 105 107; 115 103 117; 116 109 112; 117 110 101; 118 111 103
77. 119 112 101; 120 113 106; 121 114 102; 122 115 107; 123 116 103; 124 117 108
78. 125 118 124; 126 119 122; 127 120 125; 128 121 133; 129 122 135; 130 124 130
79. 131 125 131; 132 126 134; 133 124 126; 134 127 136; 135 125 127; 136 123 137
80. 137 129 132; 138 130 121; 139 131 123; 140 132 121; 141 133 126; 142 134 122
81. 143 135 127; 144 136 123; 145 137 128; 146 138 144; 147 139 142; 148 140 145
82. 149 141 153; 150 142 155; 151 144 150; 152 145 151; 153 146 154; 154 144 146
83. 155 147 156; 156 145 147; 157 143 157; 158 149 152; 159 150 141; 160 151 143
84. 161 152 141; 162 153 146; 163 154 142; 164 155 147; 165 156 143; 166 157 148
85. 167 161 35; 168 35 55; 169 55 75; 170 75 95; 171 95 115; 172 115 135
86. 173 135 155; 174 155 167; 175 162 36; 176 36 56; 177 56 76; 178 76 96
87. 179 96 116; 180 116 136; 181 136 156; 182 156 168; 183 163 37; 184 37 57
88. 185 57 77; 186 77 97; 187 97 117; 188 117 137; 189 137 157; 190 157 169
89. 191 160 34; 192 34 54; 193 54 74; 194 74 94; 195 94 114; 196 114 134
90. 197 134 154; 198 154 166; 199 159 33; 200 33 53; 201 53 73; 202 73 93
91. 203 93 113; 204 113 133; 205 133 153; 206 153 165; 207 158 32; 208 32 52
92. 209 52 72; 210 72 92; 211 92 112; 212 112 132; 213 132 152; 214 152 164
93. DEFINE MATERIAL START
94. ISOTROPIC STEEL
_ STAAD SPACE -- PAGE NO. 3

95. E 1.99947E+08
96. POISSON 0.3
97. DENSITY 76.8191
98. ALPHA 6.5E-06
99. DAMP 0.03
100. G 7.7221E+07
101. TYPE STEEL
102. STRENGTH RY 1.5 RT 1.2
103. END DEFINE MATERIAL
104. MEMBER PROPERTY COLDFORMED INDIAN
105. 1 TO 8 10 12 13 29 34 TO 48 50 52 TO 69 71 73 TO 90 92 94 TO 111 113 -
106. 115 TO 132 134 136 TO 153 155 157 TO 166 TABLE ST 80CS50X2
107. 9 11 49 51 70 72 91 93 112 114 133 135 154 156 TABLE ST 40LU40X3.15
108. 167 TO 214 TABLE ST 60CS60X2
109. CONSTANTS
110. BETA 5 MEMB 167 TO 214
111. MATERIAL STEEL ALL
112. SUPPORTS
113. 1 TO 3 38 TO 40 58 TO 60 78 TO 80 98 TO 100 118 TO 120 138 TO 140
PINNED
114. LOAD 1 LOADTYPE DEAD TITLE DL
115. SELFWEIGHT Y -1 LIST ALL
116. MEMBER LOAD
117. 183 TO 190 207 TO 214 UNI GY -0.08
118. 167 TO 182 191 TO 206 UNI GY -0.15
119. LOAD 2 LOADTYPE WIND TITLE WL_UP CASE A
120. MEMBER LOAD
121. 167 TO 190 UNI Y 0.84
122. 191 TO 214 UNI Y 0.72
123. LOAD 3 LOADTYPE WIND TITLE WL_UP CASE B
124. MEMBER LOAD
125. 167 TO 190 UNI Y -0.77
126. 191 TO 214 UNI Y -0.72
127. LOAD 4 LOADTYPE WIND TITLE WL_DN CASE A
128. MEMBER LOAD
129. 191 TO 214 UNI Y 0.84
130. 167 TO 190 UNI Y 0.72
131. LOAD 5 LOADTYPE WIND TITLE WL_DN CASE B
132. MEMBER LOAD
133. 191 TO 214 UNI Y -0.77
134. 167 TO 190 UNI Y -0.72
135. LOAD COMB 6 1.4DL
136. 1 1.4
137. LOAD COMB 7 1.2DL+WL_UP CASE A
138. 1 1.2 2 1.0
139. LOAD COMB 8 1.2DL+WL_UP CASE B
140. 1 1.2 3 1.0
141. LOAD COMB 9 1.2DL+WL_DN CASE A
142. 1 1.2 4 1.0
143. LOAD COMB 10 1.2DL+WL_DN CASE B
144. 1 1.2 5 1.0
145. LOAD COMB 11 0.9DL+WL_UP CASE A
146. 1 0.9 2 1.0
147. LOAD COMB 12 0.9DL+WL_UP CASE B
148. 1 0.9 3 1.0
149. LOAD COMB 13 0.9DL+WL_DN CASE A
150. 1 0.9 4 1.0
_ STAAD SPACE -- PAGE NO. 4

151. LOAD COMB 14 0.9DL+WL_DN CASE B

152. 1 0.9 5 1.0
153. LOAD COMB 15 DL+WL_UP CASE A
154. 1 1.0 2 1.0
155. LOAD COMB 16 DL+WL_UP CASE B
156. 1 1.0 3 1.0
157. LOAD COMB 17 DL+WL_DN CASE A
158. 1 1.0 4 1.0
159. LOAD COMB 18 DL+WL_DN CASE B
160. 1 1.0 5 1.0
161. LOAD COMB 19 DL+0.6WL_UP CASE A
162. 1 1.0 2 0.6
163. LOAD COMB 20 DL+0.6WL_UP CASE B
164. 1 1.0 3 0.6
165. LOAD COMB 21 DL+0.6WL_DN CASE A
166. 1 1.0 4 0.6
167. LOAD COMB 22 DL+0.6WL_DN CASE B
168. 1 1.0 5 0.6
169. PERFORM ANALYSIS
_
PROBLEM STATISTICS
-----------------------------------

NUMBER OF JOINTS 152 NUMBER OF MEMBERS 195

NUMBER OF PLATES 0 NUMBER OF SOLIDS 0
NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 21

Using 64-bit analysis engine.

SOLVER USED IS THE IN-CORE ADVANCED MATH SOLVER

TOTAL PRIMARY LOAD CASES = 5, TOTAL DEGREES OF FREEDOM =

849
TOTAL LOAD COMBINATION CASES = 17 SO FAR.
_

170. PARAMETER 1
171. CODE AISI 2016
172. FYLD 355000 ALL
173. FU 450000 ALL
174. RATIO 1 ALL
175. KY 1 MEMB 1 TO 3 6 7 29 34 41 TO 43 46 47 54 55 62 TO 64 67 68 75 76 -
176. 83 TO 85 88 89 96 97 104 TO 106 109 110 117 118 125 TO 127 130 131 138 139
-
177. 146 TO 148 151 152 159 160
178. KZ 1 MEMB 1 TO 3 6 7 29 34 41 TO 43 46 47 54 55 62 TO 64 67 68 75 76 -
179. 83 TO 85 88 89 96 97 104 TO 106 109 110 117 118 125 TO 127 130 131 138 139
-
180. 146 TO 148 151 152 159 160
181. LY 0.700001 MEMB 1 6 29 41 46 54 62 67 75 83 88 96 104 109 117 125 130 138
-
182. 146 151 159
183. LY 0.895002 MEMB 2 42 63 84 105 126 147
184. LY 1.09 MEMB 3 7 34 43 47 55 64 68 76 85 89 97 106 110 118 127 131 139 148
-
_ STAAD SPACE -- PAGE NO. 5

185. 152 160

186. LZ 0.700001 MEMB 1 6 29 41 46 54 62 67 75 83 88 96 104 109 117 125 130 138
-
187. 146 151 159
188. LZ 0.895002 MEMB 2 42 63 84 105 126 147
189. LZ 1.09 MEMB 3 7 34 43 47 55 64 68 76 85 89 97 106 110 118 127 131 139 148
-
190. 152 160
191. KY 1 MEMB 4 5 8 10 12 13 35 TO 40 44 45 48 50 52 53 56 TO 61 65 66 69 71
73 -
192. 74 77 TO 82 86 87 90 92 94 95 98 TO 103 107 108 111 113 115 116 119 TO 124
-
193. 128 129 132 134 136 137 140 TO 145 149 150 153 155 157 158 161 TO 166
194. KZ 1 MEMB 4 5 8 10 12 13 35 TO 40 44 45 48 50 52 53 56 TO 61 65 66 69 71
73 -
195. 74 77 TO 82 86 87 90 92 94 95 98 TO 103 107 108 111 113 115 116 119 TO 124
-
196. 128 129 132 134 136 137 140 TO 145 149 150 153 155 157 158 161 TO 166
197. LY 5.89726 MEMB 4 5 8 10 12 13 35 TO 40 44 45 48 50 52 53 56 TO 61 65 66
69 -
198. 71 73 74 77 TO 82 86 87 90 92 94 95 98 TO 103 107 108 111 113 115 116 119 -
199. 120 TO 124 128 129 132 134 136 137 140 TO 145 149 150 153 155 157 158 161 -
200. 162 TO 166
201. LZ 5.89726 MEMB 4 5 8 10 12 13 35 TO 40 44 45 48 50 52 53 56 TO 61 65 66
69 -
202. 71 73 74 77 TO 82 86 87 90 92 94 95 98 TO 103 107 108 111 113 115 116 119 -
203. 120 TO 124 128 129 132 134 136 137 140 TO 145 149 150 153 155 157 158 161 -
204. 162 TO 166
205. CHECK CODE ALL
_STEEL DESIGN _
Appendix F Staad Output

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 6

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 7

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 8

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 9

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 10

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 11

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 12

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 13

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 58_ SECTION:ST 80CS50X2 LEN: 0.581 LOC: 0.581 |
| STATUS: PASS RATIO: 0.388 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 14

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 15

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 68_ SECTION:ST 80CS50X2 LEN: 0.310 LOC: 0.000 |
| STATUS: PASS RATIO: 0.182 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 69_ SECTION:ST 80CS50X2 LEN: 0.763 LOC: 0.763 |
| STATUS: PASS RATIO: 0.220 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 16

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 17

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 79_ SECTION:ST 80CS50X2 LEN: 0.581 LOC: 0.581 |
| STATUS: PASS RATIO: 0.341 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 80_ SECTION:ST 80CS50X2 LEN: 0.777 LOC: 0.000 |
| STATUS: PASS RATIO: 0.199 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 18

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 19

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 90_ SECTION:ST 80CS50X2 LEN: 0.763 LOC: 0.763 |
| STATUS: PASS RATIO: 0.230 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 91_ SECTION:ST 40LU40X3.15 LEN: 0.982 LOC: 0.655 |
| STATUS: PASS RATIO: 0.168 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 20

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 21

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 101_ SECTION:ST 80CS50X2 LEN: 0.777 LOC: 0.000 |
| STATUS: PASS RATIO: 0.210 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 102_ SECTION:ST 80CS50X2 LEN: 0.482 LOC: 0.482 |
| STATUS: PASS RATIO: 0.722 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|

_ STAAD SPACE -- PAGE NO. 22

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 23

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 25

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 26

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 27

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 28

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 29

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 30

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 31

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 32

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 33

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 34

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 35

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 36

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 173_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.442 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 37

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 38

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 183_ SECTION:ST 60CS60X2 LEN: 0.600 LOC: 0.600 |
| STATUS: PASS RATIO: 0.072 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 184_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.396 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 39

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 40

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 194_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.344 REF: Eq. H1.1-2 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 195_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.344 REF: Eq. H1.1-2 LC: 10 |
|-----------------------------------------------------------------------------|

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 41

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 42

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 205_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.444 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 206_ SECTION:ST 60CS60X2 LEN: 0.600 LOC: 0.000 |
| STATUS: PASS RATIO: 0.079 REF: Sec. H2 LC: 10 |
|-----------------------------------------------------------------------------|

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 43

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

_ STAAD SPACE -- PAGE NO. 44

STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)

206. PARAMETER 2
207. CODE AISI 2016
208. STEEL TAKE OFF LIST ALL
_ STAAD SPACE -- PAGE NO. 45

_STEEL TAKE OFF _

_
STEEL TAKE-OFF
--------------

PROFILE LENGTH (METE) WEIGHT (KN)

_
ST 80CS50X2 60.08 1.781
ST 40LU40X3.15 13.72 0.243
ST 60CS60X2 115.20 3.416
----------------
TOTAL = 5.441

END OF DATA FROM INTERNAL STORAGE

209. FINISH

* END OF THE STAAD.Pro RUN *

DATE= NOV 9, 2024 TIME= 6:54:19

Appendix G Utilization Ratio Appendix H GA Drawing

Actua
Bea Claus L/
Design l Allowabl
m Analysis Normalized Ratio e C
Ratio e Ratio
(Actual/Allowabl
e)

Eq.
1 80CS50X2 80CS50X2 0.057 1.000 0.057 9
H1.1-1
Eq.
2 80CS50X2 80CS50X2 0.101 1.000 0.101 10
H1.2-1
Eq.
3 80CS50X2 80CS50X2 0.131 1.000 0.131 8
H1.2-1
Eq.
4 80CS50X2 80CS50X2 0.335 1.000 0.335 4
H1.2-1
Eq.
5 80CS50X2 80CS50X2 0.156 1.000 0.156 8
H1.2-1
Eq.
6 80CS50X2 80CS50X2 0.149 1.000 0.149 10
H1.2-1
Eq.
7 80CS50X2 80CS50X2 0.119 1.000 0.119 8
H1.2-1
Eq.
8 80CS50X2 80CS50X2 0.142 1.000 0.142 10
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
9 0.108 1.000 0.108 10
5 5 H1.2-1
Eq.
10 80CS50X2 80CS50X2 0.346 1.000 0.346 2
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
11 0.202 1.000 0.202 8
5 5 H1.2-1
Eq.
12 80CS50X2 80CS50X2 0.361 1.000 0.361 8
H1.2-1
Sec.
13 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
29 80CS50X2 80CS50X2 0.202 1.000 0.202 10
H1.2-1
Eq.
34 80CS50X2 80CS50X2 0.221 1.000 0.221 8
H1.2-1
Sec.
35 80CS50X2 80CS50X2 0.364 1.000 0.364 10
H2
Eq.
36 80CS50X2 80CS50X2 0.202 1.000 0.202 4
H1.2-1
Eq.
37 80CS50X2 80CS50X2 0.222 1.000 0.222 10
H1.2-1
Eq.
38 80CS50X2 80CS50X2 0.129 1.000 0.129 8
H1.2-1
Eq.
39 80CS50X2 80CS50X2 0.446 1.000 0.446 2
H1.2-1
Sec.
40 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
41 80CS50X2 80CS50X2 0.090 1.000 0.090 9
H1.1-1
Eq.
42 80CS50X2 80CS50X2 0.173 1.000 0.173 10
H1.2-1
Eq.
43 80CS50X2 80CS50X2 0.227 1.000 0.227 8
H1.2-1
Eq.
44 80CS50X2 80CS50X2 0.601 1.000 0.601 4
H1.2-1
Eq.
45 80CS50X2 80CS50X2 0.279 1.000 0.279 8
H1.2-1
Eq.
46 80CS50X2 80CS50X2 0.258 1.000 0.258 10
H1.2-1
Eq.
47 80CS50X2 80CS50X2 0.206 1.000 0.206 8
H1.2-1
Eq.
48 80CS50X2 80CS50X2 0.253 1.000 0.253 10
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
49 0.184 1.000 0.184 10
5 5 H1.2-1
Eq.
50 80CS50X2 80CS50X2 0.596 1.000 0.596 2
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
51 0.338 1.000 0.338 8
5 5 H1.2-1
Eq.
52 80CS50X2 80CS50X2 0.632 1.000 0.632 8
H1.2-1
Sec.
53 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
54 80CS50X2 80CS50X2 0.353 1.000 0.353 10
H1.2-1
Eq.
55 80CS50X2 80CS50X2 0.383 1.000 0.383 8
H1.2-1
Sec.
56 80CS50X2 80CS50X2 0.638 1.000 0.638 10
H2
Eq.
57 80CS50X2 80CS50X2 0.366 1.000 0.366 4
H1.2-1
Eq.
58 80CS50X2 80CS50X2 0.388 1.000 0.388 10
H1.2-1
Eq.
59 80CS50X2 80CS50X2 0.231 1.000 0.231 8
H1.2-1
Eq.
60 80CS50X2 80CS50X2 0.781 1.000 0.781 2
H1.2-1
Sec.
61 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
62 80CS50X2 80CS50X2 0.085 1.000 0.085 9
H1.1-1
Eq.
63 80CS50X2 80CS50X2 0.155 1.000 0.155 10
H1.2-1
Eq.
64 80CS50X2 80CS50X2 0.200 1.000 0.200 8
H1.2-1
Eq.
65 80CS50X2 80CS50X2 0.530 1.000 0.530 4
H1.2-1
Eq.
66 80CS50X2 80CS50X2 0.241 1.000 0.241 8
H1.2-1
Eq.
67 80CS50X2 80CS50X2 0.232 1.000 0.232 10
H1.2-1
Eq.
68 80CS50X2 80CS50X2 0.182 1.000 0.182 8
H1.2-1
Eq.
69 80CS50X2 80CS50X2 0.220 1.000 0.220 10
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
70 0.161 1.000 0.161 10
5 5 H1.2-1
Eq.
71 80CS50X2 80CS50X2 0.537 1.000 0.537 2
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
72 0.309 1.000 0.309 8
5 5 H1.2-1
Eq.
73 80CS50X2 80CS50X2 0.565 1.000 0.565 8
H1.2-1
Sec.
74 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
75 80CS50X2 80CS50X2 0.316 1.000 0.316 10
H1.2-1
Eq.
76 80CS50X2 80CS50X2 0.344 1.000 0.344 8
H1.2-1
Sec.
77 80CS50X2 80CS50X2 0.570 1.000 0.570 10
H2
Eq.
78 80CS50X2 80CS50X2 0.317 1.000 0.317 4
H1.2-1
Eq.
79 80CS50X2 80CS50X2 0.341 1.000 0.341 10
H1.2-1
Eq.
80 80CS50X2 80CS50X2 0.199 1.000 0.199 8
H1.2-1
Eq.
81 80CS50X2 80CS50X2 0.699 1.000 0.699 2
H1.2-1
Sec.
82 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
83 80CS50X2 80CS50X2 0.086 1.000 0.086 9
H1.1-1
Eq.
84 80CS50X2 80CS50X2 0.160 1.000 0.160 10
H1.2-1
Eq.
85 80CS50X2 80CS50X2 0.210 1.000 0.210 8
H1.2-1
Eq.
86 80CS50X2 80CS50X2 0.550 1.000 0.550 4
H1.2-1
Eq.
87 80CS50X2 80CS50X2 0.256 1.000 0.256 8
H1.2-1
Eq.
88 80CS50X2 80CS50X2 0.238 1.000 0.238 10
H1.2-1
Eq.
89 80CS50X2 80CS50X2 0.190 1.000 0.190 8
H1.2-1
Eq.
90 80CS50X2 80CS50X2 0.230 1.000 0.230 10
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
91 0.168 1.000 0.168 10
5 5 H1.2-1
Eq.
92 80CS50X2 80CS50X2 0.553 1.000 0.553 2
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
93 0.313 1.000 0.313 8
5 5 H1.2-1
Eq.
94 80CS50X2 80CS50X2 0.582 1.000 0.582 8
H1.2-1
Sec.
95 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
96 80CS50X2 80CS50X2 0.325 1.000 0.325 10
H1.2-1
Eq.
97 80CS50X2 80CS50X2 0.354 1.000 0.354 8
H1.2-1
Sec.
98 80CS50X2 80CS50X2 0.588 1.000 0.588 10
H2
Eq.
99 80CS50X2 80CS50X2 0.331 1.000 0.331 4
H1.2-1
Eq.
100 80CS50X2 80CS50X2 0.358 1.000 0.358 10
H1.2-1
Eq.
101 80CS50X2 80CS50X2 0.210 1.000 0.210 8
H1.2-1
Eq.
102 80CS50X2 80CS50X2 0.722 1.000 0.722 2
H1.2-1
Sec.
103 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
104 80CS50X2 80CS50X2 0.085 1.000 0.085 9
H1.1-1
Eq.
105 80CS50X2 80CS50X2 0.155 1.000 0.155 10
H1.2-1
Eq.
106 80CS50X2 80CS50X2 0.200 1.000 0.200 8
H1.2-1
Eq.
107 80CS50X2 80CS50X2 0.530 1.000 0.530 4
H1.2-1
Eq.
108 80CS50X2 80CS50X2 0.241 1.000 0.241 8
H1.2-1
Eq.
109 80CS50X2 80CS50X2 0.232 1.000 0.232 10
H1.2-1
Eq.
110 80CS50X2 80CS50X2 0.182 1.000 0.182 8
H1.2-1
Eq.
111 80CS50X2 80CS50X2 0.220 1.000 0.220 10
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
112 0.161 1.000 0.161 10
5 5 H1.2-1
Eq.
113 80CS50X2 80CS50X2 0.537 1.000 0.537 2
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
114 0.309 1.000 0.309 8
5 5 H1.2-1
Eq.
115 80CS50X2 80CS50X2 0.565 1.000 0.565 8
H1.2-1
Sec.
116 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
117 80CS50X2 80CS50X2 0.316 1.000 0.316 10
H1.2-1
Eq.
118 80CS50X2 80CS50X2 0.344 1.000 0.344 8
H1.2-1
Sec.
119 80CS50X2 80CS50X2 0.570 1.000 0.570 10
H2
Eq.
120 80CS50X2 80CS50X2 0.317 1.000 0.317 4
H1.2-1
Eq.
121 80CS50X2 80CS50X2 0.341 1.000 0.341 10
H1.2-1
Eq.
122 80CS50X2 80CS50X2 0.199 1.000 0.199 8
H1.2-1
Eq.
123 80CS50X2 80CS50X2 0.699 1.000 0.699 2
H1.2-1
Sec.
124 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
125 80CS50X2 80CS50X2 0.090 1.000 0.090 9
H1.1-1
Eq.
126 80CS50X2 80CS50X2 0.173 1.000 0.173 10
H1.2-1
Eq.
127 80CS50X2 80CS50X2 0.227 1.000 0.227 8
H1.2-1
Eq.
128 80CS50X2 80CS50X2 0.601 1.000 0.601 4
H1.2-1
Eq.
129 80CS50X2 80CS50X2 0.279 1.000 0.279 8
H1.2-1
Eq.
130 80CS50X2 80CS50X2 0.258 1.000 0.258 10
H1.2-1
Eq.
131 80CS50X2 80CS50X2 0.206 1.000 0.206 8
H1.2-1
Eq.
132 80CS50X2 80CS50X2 0.253 1.000 0.253 10
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
133 0.184 1.000 0.184 10
5 5 H1.2-1
Eq.
134 80CS50X2 80CS50X2 0.596 1.000 0.596 2
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
135 0.338 1.000 0.338 8
5 5 H1.2-1
Eq.
136 80CS50X2 80CS50X2 0.632 1.000 0.632 8
H1.2-1
Sec.
137 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
138 80CS50X2 80CS50X2 0.353 1.000 0.353 10
H1.2-1
Eq.
139 80CS50X2 80CS50X2 0.383 1.000 0.383 8
H1.2-1
Sec.
140 80CS50X2 80CS50X2 0.638 1.000 0.638 10
H2
Eq.
141 80CS50X2 80CS50X2 0.366 1.000 0.366 4
H1.2-1
Eq.
142 80CS50X2 80CS50X2 0.388 1.000 0.388 10
H1.2-1
Eq.
143 80CS50X2 80CS50X2 0.231 1.000 0.231 8
H1.2-1
Eq.
144 80CS50X2 80CS50X2 0.781 1.000 0.781 2
H1.2-1
Sec.
145 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
146 80CS50X2 80CS50X2 0.057 1.000 0.057 9
H1.1-1
Eq.
147 80CS50X2 80CS50X2 0.101 1.000 0.101 10
H1.2-1
Eq.
148 80CS50X2 80CS50X2 0.131 1.000 0.131 8
H1.2-1
Eq.
149 80CS50X2 80CS50X2 0.335 1.000 0.335 4
H1.2-1
Eq.
150 80CS50X2 80CS50X2 0.156 1.000 0.156 8
H1.2-1
Eq.
151 80CS50X2 80CS50X2 0.149 1.000 0.149 10
H1.2-1
Eq.
152 80CS50X2 80CS50X2 0.119 1.000 0.119 8
H1.2-1
Eq.
153 80CS50X2 80CS50X2 0.142 1.000 0.142 10
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
154 0.108 1.000 0.108 10
5 5 H1.2-1
Eq.
155 80CS50X2 80CS50X2 0.346 1.000 0.346 2
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
156 0.202 1.000 0.202 8
5 5 H1.2-1
Eq.
157 80CS50X2 80CS50X2 0.361 1.000 0.361 8
H1.2-1
Sec.
158 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
159 80CS50X2 80CS50X2 0.202 1.000 0.202 10
H1.2-1
Eq.
160 80CS50X2 80CS50X2 0.221 1.000 0.221 8
H1.2-1
Sec.
161 80CS50X2 80CS50X2 0.364 1.000 0.364 10
H2
Eq.
162 80CS50X2 80CS50X2 0.202 1.000 0.202 4
H1.2-1
Eq.
163 80CS50X2 80CS50X2 0.222 1.000 0.222 10
H1.2-1
Eq.
164 80CS50X2 80CS50X2 0.129 1.000 0.129 8
H1.2-1
Eq.
165 80CS50X2 80CS50X2 0.446 1.000 0.446 2
H1.2-1
Sec.
166 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Sec.
167 60CS60X2 60CS60X2 0.079 1.000 0.079 8
H2
Eq.
168 60CS60X2 60CS60X2 0.442 1.000 0.442 8
H1.2-1
Eq.
169 60CS60X2 60CS60X2 0.389 1.000 0.389 8
H1.2-1
Eq.
170 60CS60X2 60CS60X2 0.345 1.000 0.345 8
H1.2-1
Eq.
171 60CS60X2 60CS60X2 0.345 1.000 0.345 8
H1.2-1
Eq.
172 60CS60X2 60CS60X2 0.389 1.000 0.389 8
H1.2-1
Eq.
173 60CS60X2 60CS60X2 0.442 1.000 0.442 8
H1.2-1
Sec.
174 60CS60X2 60CS60X2 0.079 1.000 0.079 8
H2
Sec.
175 60CS60X2 60CS60X2 0.079 1.000 0.079 8
H2
Eq.
176 60CS60X2 60CS60X2 0.445 1.000 0.445 8
H1.2-1
Eq.
177 60CS60X2 60CS60X2 0.392 1.000 0.392 8
H1.2-1
Eq.
178 60CS60X2 60CS60X2 0.346 1.000 0.346 8
H1.2-1
Eq.
179 60CS60X2 60CS60X2 0.346 1.000 0.346 8
H1.2-1
Eq.
180 60CS60X2 60CS60X2 0.392 1.000 0.392 8
H1.2-1
Eq.
181 60CS60X2 60CS60X2 0.445 1.000 0.445 8
H1.2-1
Sec.
182 60CS60X2 60CS60X2 0.079 1.000 0.079 8
H2
Sec.
183 60CS60X2 60CS60X2 0.072 1.000 0.072 8
H2
Eq.
184 60CS60X2 60CS60X2 0.396 1.000 0.396 8
H1.2-1
Eq.
185 60CS60X2 60CS60X2 0.345 1.000 0.345 8
H1.2-1
Eq.
186 60CS60X2 60CS60X2 0.310 1.000 0.310 8
H1.2-1
Eq.
187 60CS60X2 60CS60X2 0.310 1.000 0.310 8
H1.2-1
Eq.
188 60CS60X2 60CS60X2 0.345 1.000 0.345 8
H1.2-1
Eq.
189 60CS60X2 60CS60X2 0.396 1.000 0.396 8
H1.2-1
Sec.
190 60CS60X2 60CS60X2 0.072 1.000 0.072 8
H2
Sec.
191 60CS60X2 60CS60X2 0.079 1.000 0.079 10
H2
Eq.
192 60CS60X2 60CS60X2 0.442 1.000 0.442 10
H1.2-1
Eq.
193 60CS60X2 60CS60X2 0.388 1.000 0.388 10
H1.1-2
Eq.
194 60CS60X2 60CS60X2 0.344 1.000 0.344 10
H1.1-2
Eq.
195 60CS60X2 60CS60X2 0.344 1.000 0.344 10
H1.1-2
Eq.
196 60CS60X2 60CS60X2 0.388 1.000 0.388 10
H1.1-2
Eq.
197 60CS60X2 60CS60X2 0.442 1.000 0.442 10
H1.2-1
Sec.
198 60CS60X2 60CS60X2 0.079 1.000 0.079 10
H2
Sec.
199 60CS60X2 60CS60X2 0.079 1.000 0.079 10
H2
Eq.
200 60CS60X2 60CS60X2 0.444 1.000 0.444 10
H1.2-1
Eq.
201 60CS60X2 60CS60X2 0.389 1.000 0.389 10
H1.1-2
Eq.
202 60CS60X2 60CS60X2 0.345 1.000 0.345 10
H1.2-1
Eq.
203 60CS60X2 60CS60X2 0.345 1.000 0.345 10
H1.2-1
Eq.
204 60CS60X2 60CS60X2 0.389 1.000 0.389 10
H1.1-2
Eq.
205 60CS60X2 60CS60X2 0.444 1.000 0.444 10
H1.2-1
Sec.
206 60CS60X2 60CS60X2 0.079 1.000 0.079 10
H2
Sec.
207 60CS60X2 60CS60X2 0.072 1.000 0.072 10
H2
Eq.
208 60CS60X2 60CS60X2 0.397 1.000 0.397 10
H1.2-1
Eq.
209 60CS60X2 60CS60X2 0.348 1.000 0.348 10
H1.2-1
Eq.
210 60CS60X2 60CS60X2 0.311 1.000 0.311 10
H1.2-1
Eq.
211 60CS60X2 60CS60X2 0.311 1.000 0.311 10
H1.2-1
Eq.
212 60CS60X2 60CS60X2 0.348 1.000 0.348 10
H1.2-1
Eq.
213 60CS60X2 60CS60X2 0.397 1.000 0.397 10
H1.2-1
Sec.
214 60CS60X2 60CS60X2 0.072 1.000 0.072 10
H2

Appendix G Utilization Ratio Appendix H GA Drawing

NOTES:-

5H8 Location
Latitude
Longtitude
Total System Capacity
Module Capacity
:XXXXXXXX
:XXXXXXXX
:897.7KWP
:635
Total No of Module :1414
PV Array Tilt Angle :5°
Mounting Type :Rooftop

3000.0 3000.0 3000.0 3000.0 3000.0 3000.0

Solar Panel
2382x1134x30

1154
1154
18
5 50
19 4
1154
1154
10
45

1088
896

61 45
703

10
00 SA 09/11/24 Issued for Quotation

Rev By Date Description

2200 2200 Manufacturer Details:

AL Babtain Metalogalva Solar
Dammam, 3rd Industrial CIty
Kingdom of Saudi Arabia

Project Name: Solar Carport Project at concrete roof - Zamil

Name Date Drawing Title:

Drawn SA PV Layout and structure drawings -
Checked SA Zamil(5H8)

Approved PR

Drawing No. Rev No. Sheet No.

B269-475-C-Cal-0056-Design Calculation of Sludge Sump Shed-I - Peb Structure
No ratings yet
B269-475-C-Cal-0056-Design Calculation of Sludge Sump Shed-I - Peb Structure
78 pages
(Lalley) Random Walks On Infinite Groups
100% (1)
(Lalley) Random Walks On Infinite Groups
373 pages
Structure Design Report 4H7@1000 - Purlin
No ratings yet
Structure Design Report 4H7@1000 - Purlin
54 pages
Technical Report - R2 - 22.09.2024
No ratings yet
Technical Report - R2 - 22.09.2024
48 pages
Structure Design Report 3H8@1000 - Purlin
No ratings yet
Structure Design Report 3H8@1000 - Purlin
51 pages
Control Room Design
No ratings yet
Control Room Design
45 pages
DBR-Surveys Geotech and Hydro. Rev.B
No ratings yet
DBR-Surveys Geotech and Hydro. Rev.B
47 pages
Ballast Structure
No ratings yet
Ballast Structure
34 pages
ANTAI Calculation 40m Per Second ASCE 7-10
No ratings yet
ANTAI Calculation 40m Per Second ASCE 7-10
13 pages
AP01-SCIV-WRTL-IACSB-CAL-P1-415 - R0 - Design Calculation For Inverter AC Switch Box Station Foundation
No ratings yet
AP01-SCIV-WRTL-IACSB-CAL-P1-415 - R0 - Design Calculation For Inverter AC Switch Box Station Foundation
39 pages
Cannonball-Geotech Report-Final - 10-04-2022
No ratings yet
Cannonball-Geotech Report-Final - 10-04-2022
64 pages
Design Report - UPGRADATION MODERNIZATION OF INFRASTRUCTURE AT BIKANER
No ratings yet
Design Report - UPGRADATION MODERNIZATION OF INFRASTRUCTURE AT BIKANER
40 pages
Design For Module Mounting Structure-Bhadla (8,28) - R5
No ratings yet
Design For Module Mounting Structure-Bhadla (8,28) - R5
8 pages
2V28 - 25deg - Biposte Structure - Design Report
No ratings yet
2V28 - 25deg - Biposte Structure - Design Report
36 pages
MMS Structure Wind Pressure Calculation1
No ratings yet
MMS Structure Wind Pressure Calculation1
3 pages
Saatviki Installation Manual
No ratings yet
Saatviki Installation Manual
28 pages
224 MMS
No ratings yet
224 MMS
26 pages
Design Basis of Fan Support Structure 20200321
No ratings yet
Design Basis of Fan Support Structure 20200321
13 pages
Pepsico - Detail Design Package - Rev.00
No ratings yet
Pepsico - Detail Design Package - Rev.00
43 pages
Structure Design Report
100% (1)
Structure Design Report
70 pages
Solar Carport
No ratings yet
Solar Carport
20 pages
2x5 - Design Report
No ratings yet
2x5 - Design Report
40 pages
Detailed Comments Double carport-MEA - 20.04.24
No ratings yet
Detailed Comments Double carport-MEA - 20.04.24
10 pages
Structural Design
No ratings yet
Structural Design
10 pages
Seasonal Structure With Manual Tilting Single Pole Dual Panel
No ratings yet
Seasonal Structure With Manual Tilting Single Pole Dual Panel
7 pages
2X4 (SEASONAL TILT) STRUCTURE ASSEMBLY LAUOUT, BOQ & Design
No ratings yet
2X4 (SEASONAL TILT) STRUCTURE ASSEMBLY LAUOUT, BOQ & Design
3 pages
DBR - Delhi GPO
No ratings yet
DBR - Delhi GPO
16 pages
Vavade - 4mw - All Layouts
No ratings yet
Vavade - 4mw - All Layouts
5 pages
Report
No ratings yet
Report
17 pages
CIvil Specification
No ratings yet
CIvil Specification
45 pages
Ground Mount Module Mounting Structure - 15.06.23
No ratings yet
Ground Mount Module Mounting Structure - 15.06.23
2 pages
Summative Test 2 (Grade 7 - Q3)
No ratings yet
Summative Test 2 (Grade 7 - Q3)
11 pages
PropertY Calculation 75CS40X10X1.2
No ratings yet
PropertY Calculation 75CS40X10X1.2
15 pages
Wind - PZ Calculation
No ratings yet
Wind - PZ Calculation
4 pages
Load Calculations - 47 Ms
No ratings yet
Load Calculations - 47 Ms
3 pages
Structure Design Calculation of Rooftop Solar Project
100% (1)
Structure Design Calculation of Rooftop Solar Project
13 pages
MMS Structure
No ratings yet
MMS Structure
8 pages
Mounting Structures PDF
No ratings yet
Mounting Structures PDF
13 pages
Dyn Analysis Tracker
No ratings yet
Dyn Analysis Tracker
10 pages
RPIPL-KNK-OA-AMP-CE-DWG-SCB-001-Model - PDF R2
No ratings yet
RPIPL-KNK-OA-AMP-CE-DWG-SCB-001-Model - PDF R2
2 pages
Ib Vogt Solar India Pvt. LTD
No ratings yet
Ib Vogt Solar India Pvt. LTD
2 pages
Lecture Planner Physical Chemistry by Sudhanshu Kumar Sir
No ratings yet
Lecture Planner Physical Chemistry by Sudhanshu Kumar Sir
2 pages
SWLD SKYP1 57.5MW TL E DWG LTCR 01 - Approved
No ratings yet
SWLD SKYP1 57.5MW TL E DWG LTCR 01 - Approved
1 page
DBR of 2PX8 Table 30D 0.5 NGL Ground Mount MMS
No ratings yet
DBR of 2PX8 Table 30D 0.5 NGL Ground Mount MMS
8 pages
PLP Single Row Carport - Structural Construction Drawings
No ratings yet
PLP Single Row Carport - Structural Construction Drawings
5 pages
Design of Carport
No ratings yet
Design of Carport
3 pages
Chapter 1
No ratings yet
Chapter 1
73 pages
EG0222032301 Solar Carport Mounting System-Area A ASCE 7-10) - 10x21
No ratings yet
EG0222032301 Solar Carport Mounting System-Area A ASCE 7-10) - 10x21
20 pages
Kirill v. Rozhdestvensky - Aerodynamics of A Lifting System in Extreme Ground Effect
No ratings yet
Kirill v. Rozhdestvensky - Aerodynamics of A Lifting System in Extreme Ground Effect
357 pages
25 1
No ratings yet
25 1
5 pages
2022 - 12 - 07 - HMEL - ARRAY LAYOUT - R1-Layout
No ratings yet
2022 - 12 - 07 - HMEL - ARRAY LAYOUT - R1-Layout
1 page
Vivek Jain SPM 8th Ed (OCR) - 867
No ratings yet
Vivek Jain SPM 8th Ed (OCR) - 867
1 page
Sop For Proto
No ratings yet
Sop For Proto
7 pages
Multibay Portal Deflection Due To Lateral Loads: Input: Symbol Value Unit Description
No ratings yet
Multibay Portal Deflection Due To Lateral Loads: Input: Symbol Value Unit Description
3 pages
Mms Design Paper
No ratings yet
Mms Design Paper
12 pages
Scorpius SRT 60 ROW Tracker Datasheet
No ratings yet
Scorpius SRT 60 ROW Tracker Datasheet
4 pages
Interim Geotech Report For Umer Hospital Sanda Raj Garh Lahore
No ratings yet
Interim Geotech Report For Umer Hospital Sanda Raj Garh Lahore
9 pages
S. No. Signal Data Type 1 2 3 4 5 6 7 8 9
No ratings yet
S. No. Signal Data Type 1 2 3 4 5 6 7 8 9
1 page
Zhao Et Al. (202) Economy-Environment-Energy Performance Evaluation of CCHP Microgrid System - A Hybrid Multi-Criteria Decision-Making Method
No ratings yet
Zhao Et Al. (202) Economy-Environment-Energy Performance Evaluation of CCHP Microgrid System - A Hybrid Multi-Criteria Decision-Making Method
17 pages
General Structural Notes General Structural Notes: Pe Stamp
100% (1)
General Structural Notes General Structural Notes: Pe Stamp
3 pages
Concrete Block Weight Calculation: Design Specification
No ratings yet
Concrete Block Weight Calculation: Design Specification
6 pages
Solar Inter Row Spacing PDF
No ratings yet
Solar Inter Row Spacing PDF
3 pages
Xbeach Grid Tutorial: Joost Den Bieman June 3, 2013
No ratings yet
Xbeach Grid Tutorial: Joost Den Bieman June 3, 2013
12 pages
Z 150X60X20X2 Design
No ratings yet
Z 150X60X20X2 Design
3 pages
MCR Footing Design
No ratings yet
MCR Footing Design
5 pages
1.1 General Details & Load Calculations - Substation Building (Pess)
No ratings yet
1.1 General Details & Load Calculations - Substation Building (Pess)
2 pages
MCR Slab
No ratings yet
MCR Slab
5 pages
Module - 2 - Modern Physics
No ratings yet
Module - 2 - Modern Physics
63 pages
Rolling Mill Extension Stability Check: Structural Information Input Data
No ratings yet
Rolling Mill Extension Stability Check: Structural Information Input Data
3 pages
Soft or Annealed Copper Wire: Standard Specification For
No ratings yet
Soft or Annealed Copper Wire: Standard Specification For
5 pages
Isometric View: Concept Drawing RPK-SE-947
No ratings yet
Isometric View: Concept Drawing RPK-SE-947
1 page
Staad Report - Bracket
No ratings yet
Staad Report - Bracket
7 pages
GL GL GL: Section B-B Section A-A
No ratings yet
GL GL GL: Section B-B Section A-A
1 page
FRAP Tutorial EMBO Debrecen
No ratings yet
FRAP Tutorial EMBO Debrecen
55 pages
Plan View Isometric View: RPK-SE-942
No ratings yet
Plan View Isometric View: RPK-SE-942
1 page
Iat 1 Dme
No ratings yet
Iat 1 Dme
3 pages
Unit-4 & 5 Possible Question
No ratings yet
Unit-4 & 5 Possible Question
4 pages
SAT Functions
No ratings yet
SAT Functions
9 pages
AM-01-Mountings Details-002
No ratings yet
AM-01-Mountings Details-002
1 page
1903 - Leader - 5+6 - Cover + Paper - Eng Med
No ratings yet
1903 - Leader - 5+6 - Cover + Paper - Eng Med
30 pages
Balason Land Requirements
No ratings yet
Balason Land Requirements
2 pages
R01 Structure Drawing of 4H7 Table Configuration
No ratings yet
R01 Structure Drawing of 4H7 Table Configuration
1 page
R01 Structure Drawing of 3H8 Table Configuration
No ratings yet
R01 Structure Drawing of 3H8 Table Configuration
1 page
Sorbothane Standard Product Guide
No ratings yet
Sorbothane Standard Product Guide
24 pages
Week 1: Progress Check
No ratings yet
Week 1: Progress Check
4 pages
R01 Structure Drawing of 5H8 Table Configuration
No ratings yet
R01 Structure Drawing of 5H8 Table Configuration
1 page
MOdal Analysis Displacement For USD
No ratings yet
MOdal Analysis Displacement For USD
4 pages
Unit - IV (Radiation)
No ratings yet
Unit - IV (Radiation)
5 pages
Penetrant Testing - Process Guide - Methods A B C D
No ratings yet
Penetrant Testing - Process Guide - Methods A B C D
1 page
Faculty Recruitment Sample Paper Physics (Sat Subject) (Category - D)
No ratings yet
Faculty Recruitment Sample Paper Physics (Sat Subject) (Category - D)
10 pages
Case Study: Exergy Accounting of A Vapor Power Plant
No ratings yet
Case Study: Exergy Accounting of A Vapor Power Plant
1 page
Hec 2024 March Intake Time Table
No ratings yet
Hec 2024 March Intake Time Table
1 page
2x2.5 Flexible-FR (TDS)
No ratings yet
2x2.5 Flexible-FR (TDS)
1 page
27 Atoms: Solutions
No ratings yet
27 Atoms: Solutions
12 pages
Mappings and Functions Best
No ratings yet
Mappings and Functions Best
22 pages
Sika - 102 Waterplug
No ratings yet
Sika - 102 Waterplug
2 pages
Chemistry Chapter 3 Notebook Work.
No ratings yet
Chemistry Chapter 3 Notebook Work.
6 pages
Ghadir PVC 2 S
No ratings yet
Ghadir PVC 2 S
1 page