Structure Design Report 4H7@1000 - Purlin
Uploaded by
SalauddinAnsariStructure Design Report 4H7@1000 - Purlin
Uploaded by
SalauddinAnsariFIXED TILT STRUCTURE FOR PHOTOVOLTAIC PANELS
1.0MW ZAMIL - SOLAR GROUND MOUNT PROJECT,
RIYAD, SAUDI ARABIA
CUSTOMER: ZAMIL
Rev. Date Revision Details Originator Checked Approved
00 09/11/24 Issued for Approval SA AM PR
© Copyright ABMTG
This document is the property of Al-Babtain Metalogalva JV (ABMTG) and may contain confidential and proprietary information. It
may not be used for any purpose other than that for which it is supplied. This document may not be wholly or partly disclosed,
copied, duplicated or in any way made use of without prior written approval of ABMTG.
TABLE OF CONTENTS 1.0 INTRODUCTION 4
1.1 Project description 4
1.2 Document scope 4
1.3 Geometry 4
1.4 Structure Description 4
2.0 CALCULATION RESOURCES 6
2.1 Loads 6
2.2 Wind Loads 6
2.3 Snow Loads 6
2.4 Ultimate Limit States (U.L.S.) 6
2.5 Service Limit States (S.L.S.) 6
3.0 BASIS OF ANALYSIS 7
3.1 Introduction 7
3.2 Materials 7
3.2.1 Fabrication methods 7
4.0 CALCULATION REPORT 8
4.1 Sections 8
4.2 Materials 8
4.3 Loads 8
4.4 Load Combinations 8
4.5 Load Application 9
4.6 Reactions (Global Extremes) 9
Appendix A Dead loads calculations
Appendix B Wind loads calculations
Appendix C Calculations for Block size
Appendix D Application of load at structures
Appendix E Staad Input
Appendix F Staad Output
Appendix G Utilization Ratio Appendix H GA Drawing
1.0 INTRODUCTION
1.1 Project description
Al-Babtain Metalogalva JV have been invited by Zamil to do the analysis, design, manufacture &
supply ofFixed tilt structures supporting photovoltaic panels, as part of 1.0 MWp Solar PV Power
Plant in Riyadh, KSA.
1.2 Document scope
The scope of this document is to perform a structural assessment of fixed tilt structures. This
document covers modelling and analysis approach, design assumptions. The results include unity
check plot and deflection plots. Wind load calculation, general arrangement drawings & analysis
results are presented in Appendices.
1.3 Geometry
The structure is composed by photovoltaic fixed tilt structure with an inclination of 5◦ supported
on column separated by 1.40 m embedded in ground. The lower edge of the panel is 1.00m and
the higher edge 1.50m above top of ground level. The total number of panels installed in each
structure is 4 & arranged in 4 rows & 1 columns in vertical orientation. The dimensions of each
panel are 2382 × 1134 × 35 mm.
1.4 Structure Description
The structure will be made in steel grade S355. The panels will be fixed to the secondary beams
by clamps. The remaining connections are materialized by bolts (SS306). The Frames have the
geometry represented are spaced 1.40m.
Figure 1.1 Fixed tilt Structure– Side View
Figure 1.2 Fixed tilt Structure– Front View
Figure 1.3 Fixed tilt Structure with PV panels – Isometric View
2.0 CALCULATION RESOURCES
2.1 Loads
The loads are defined by the ASCE 7-16/SBC 301 and customer requirement.
Permanent Loads: self-weight and panels weight.
Variable Loads: wind loads and snow loads.
2.2 Wind Loads
Wind loading is derived from the customer specifications and rules given in SBC 301-CR-18 &
ASCE/SEI 7-16. The Basic wind speed (3-sec gust) considered is 160kmph (44.44 m/s). The
Exposure category considered is
C. The peak velocity pressure, qh will be 0.874 kN/m2.
The net pressure coefficients for pitched fixed tilt solar structures are calculated as per latest SBC
301-CR-18 & ASCE/SEI 7-16, Chapter 27-Figure 27.3-4. See Appendix A for detail wind loads
calculation.
2.3 Snow Loads
No snow loads are considered for the design (customer requirement).
2.4 Allowable Stress Design (ASD)
Allowable Stress Design (ASD) also known as Working Stress Design (WSD) method is based on
the principle that stresses developed in the structural members should not exceed a certain
fraction of elastic limit.
2.5 Load and Resistance Factor Design (LRFD)
Limit State Design (LSD), also known as Load and Resistance Factor Design (LRFD), refers to a
design method used in structural engineering. A limit state is a condition of a structure beyond
which it no longer fulfills the relevant design criteria.
2.6 Service Limit States (S.L.S.)
The service limit states were considered for the quasi-permanent combination and frequent
combination, which the respective beams vertical deformations were limited to L/240
3.0 BASIS OF ANALYSIS
3.1 Introduction
Stability verification, forces and displacements determination were calculated with STAAD Pro
structural analysis program for modelling the Ultimate Limit State.
3.2 Materials
The materials Material Standard
used for
fabrication of the
structure are:
Element
Steel Profiles & S355 EN 10025
plates
Bolts & Nuts SS304 EN4017
4.0 CALCULATION REPORT
4.1 Sections
Prop Name Area Iyy Izz J Material Source
(in2) (in4) (in4) (in4)
1 80CS50X2 0.598 0.320 0.963 0.001 STEEL Legacy
2 80CS50X2 0.598 0.320 0.963 0.001 STEEL Legacy
3 40LU40X3.15 0.358 0.087 0.087 0.002 STEEL Legacy
4 60CS60X2 0.598 0.447 0.577 0.001 STEEL Legacy
4.2 Material
Mat Name E Density
(kip/in2) (kip/in3) (/°F)
1 STEEL 29,000.000 0.300 0.000 0.000
4.3 Load Combination
L/C Type Name
1 Primary DL
2 Primary WL_UP Case A
3 Primary WL_UP Case B
4 Primary WL_DN Case A
5 Primary WL_DN Case B
6 Combination 1.4DL
7 Combination 1.2DL+WL_UP Case A
8 Combination 1.2DL+WL_UP Case B
9 Combination 1.2DL+WL_DN Case A
10 Combination 1.2DL+WL_DN Case B
11 Combination 0.9DL+WL_UP Case A
12 Combination 0.9DL+WL_UP Case B
13 Combination 0.9DL+WL_DN Case A
14 Combination 0.9DL+WL_DN Case B
15 Combination DL+WL_UP Case A
16 Combination DL+WL_UP Case B
17 Combination DL+WL_DN Case A
18 Combination DL+WL_DN Case B
19 Combination DL+0.6WL_UP Case A
20 Combination DL+0.6WL_UP Case B
21 Combination DL+0.6WL_DN Case A
22 Combination DL+0.6WL_DN Case B
Appendix A Dead loads calculations
CALCULATION OF DEAD LOAD
Solar module dimension Length Width HT
2.382 1.134 30
Weight per module 34 Kg
Numbers of module 28 No.
Weight of all module 952 Kg 9.342 KN
Length of purlin 16.8 m
Number of Purlin 5 No.
Member load per unit length 0.111 KN/m
Appendix B Wind loads calculations
Panel Characteristics
Height a = 2382 mm
Width b = 1134 mm
Thickness d = 30 mm
Weight = 34 kG
Distance of mounting slots to the edge c = 491 mm
Maximum power P = 580 wP
Self-weight of the panels p = 0.123 kN/m2
Panels layout characteristics
Panels orientation Horizontal / Landscape
Type of panels disposition 2
No. of rows/structure i 4
No. of columns/structure j 7
Layout model 4H7
Internal clamps width Ci = 20 mm
Edge clamps width Ce = 45 mm
Distance between panels e = 20 mm
Extra length on the principal beams f = 90 mm
Secondary beams orientation Inclined
Secondary beams length Sb = 8696 mm
Principal beams length Pb = 8148 mm
Structure characteristics
Type of Structure/Table Monoslope
Obstruction under the Structure/Table Unobstructed
Table inclination with horizontal plane = 5º deg
Panels Min. distance to the ground g = 500 mm
Panels Max.distance to the ground h = 901 mm
Panels Mean distance to the ground z = 700 mm
Design working life (years) yrs = 25 Years
Load factor w = 1
Risk category of Building = I
Basic Wind Speed V = 44.44 m/s
Wind directionality factor Kd = 0.85
Exposure category = C
Topography factor Kzt = 1
Ground Elevation factor Ke = 1
Gust effect factor Gf = 0.85
Velocity pressure Exposure Coeff. Kz = 0.85
Velocity pressure qh = 874.85 N/m2
Net pressure Coefficients, CN & Net Coeffiecients Net design Pressure
design pressure, p CNW CNL pNW pNL
Load case A0 1.20 0.30 0.89 0.77 KN/m2
Wind direction, = 0o
Load case B0 -1.10 -0.10 -0.82 -0.77 KN/m2
Load case A180 1.20 0.30 0.89 0.77 KN/m2
Wind direction, = 180o
Load case B180 -1.10 -0.10 -0.82 -0.77 KN/m2
A90 -0.80 -0.77 KN/m2
For <h
B90 0.80 0.77 KN/m2
For >h, A90 -0.60 -0.77 KN/m2
Wind direction, = 90o
<2h B90 0.50 0.77 KN/m2
A90 -0.30 -0.77 KN/m2
For >2h
B90 0.30 0.77 KN/m2
Panel Length m 2.382 Case A 0.803 0.693 KN/m2
y = 0°
Panel Width m 1.134 Case B -0.737 -0.69 KN/m2
No of solar panel nos 28 y= Case A 0.80347 0.693 KN/m2
180° -
Total area of solar Panels Sqm 75.633 Case B 0.73651 -0.69 KN/m2
Number of purlin nos 5
Lenth of Purlin m 16.8
Appendix C Calculations for Block size
Total Uplift as per Staad Analysis = 0.37KN = 37KG
Safety Factor = 1.5
Required concrete block weight = 1.5 x 37 = 55.5Kg
Foundation Size = 300x300x300
Weight of concrete foundation Provided = 64.8KG
Appendix D Application of load at structures
Appendix E Staad Input
1. STAAD SPACE
INPUT FILE: D:\ABMTG DESIGN\OneDrive - Al-Babtain Metalogalva
(ABL)\DESIGN\SOLAR RFQ's\Fixed Tilt 2024.. .STD
2. START JOB INFORMATION
3. ENGINEER DATE 31-OCT-24
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 0 0 0; 2 1.8 0 0; 3 3.60001 0 0; 4 0 0.682001 0; 5 1.8 0.840002 0
9. 6 3.60001 0.996002 0; 7 4.22267 1.04997 0; 8 -0.483143 0.639592 0
10. 9 0.861688 0.757638 0; 10 2.7365 0.921164 0; 11 0 0.225 0
11. 12 3.60001 0.450001 0; 26 0 0.560001 0; 28 3.60001 0.750002 0
12. 29 -0.423373 0.644838 0; 30 0.726209 0.745746 0; 31 1.89963 0.848636 0
13. 32 3.04534 0.947931 0; 33 4.17286 1.04565 0; 34 0 0 3.00001; 35 1.8 0 3.00001
14. 36 3.60001 0 3.00001; 37 0 0.682001 3.00001; 38 1.8 0.840002 3.00001
15. 39 3.60001 0.996002 3.00001; 40 4.22267 1.04997 3.00001
16. 41 -0.483143 0.639592 3.00001; 42 0.861688 0.757638 3.00001
17. 43 2.7365 0.921164 3.00001; 44 0 0.225 3.00001; 45 3.60001 0.450001 3.00001
18. 46 0 0.560001 3.00001; 47 3.60001 0.750002 3.00001
19. 48 -0.423373 0.644838 3.00001; 49 0.726209 0.745746 3.00001
20. 50 1.89963 0.848636 3.00001; 51 3.04534 0.947931 3.00001
21. 52 4.17286 1.04565 3.00001; 53 0 0 6.00001; 54 1.8 0 6.00001
22. 55 3.60001 0 6.00001; 56 0 0.682001 6.00001; 57 1.8 0.840002 6.00001
23. 58 3.60001 0.996002 6.00001; 59 4.22267 1.04997 6.00001
24. 60 -0.483143 0.639592 6.00001; 61 0.861688 0.757638 6.00001
25. 62 2.7365 0.921164 6.00001; 63 0 0.225 6.00001; 64 3.60001 0.450001 6.00001
26. 65 0 0.560001 6.00001; 66 3.60001 0.750002 6.00001
27. 67 -0.423373 0.644838 6.00001; 68 0.726209 0.745746 6.00001
28. 69 1.89963 0.848636 6.00001; 70 3.04534 0.947931 6.00001
29. 71 4.17286 1.04565 6.00001; 72 0 0 9.00002; 73 1.8 0 9.00002
30. 74 3.60001 0 9.00002; 75 0 0.682001 9.00002; 76 1.8 0.840002 9.00002
31. 77 3.60001 0.996002 9.00002; 78 4.22267 1.04997 9.00002
32. 79 -0.483143 0.639592 9.00002; 80 0.861688 0.757638 9.00002
33. 81 2.7365 0.921164 9.00002; 82 0 0.225 9.00002; 83 3.60001 0.450001 9.00002
34. 84 0 0.560001 9.00002; 85 3.60001 0.750002 9.00002
35. 86 -0.423373 0.644838 9.00002; 87 0.726209 0.745746 9.00002
36. 88 1.89963 0.848636 9.00002; 89 3.04534 0.947931 9.00002
37. 90 4.17286 1.04565 9.00002; 91 0 0 12; 92 1.8 0 12; 93 3.60001 0 12
38. 94 0 0.682001 12; 95 1.8 0.840002 12; 96 3.60001 0.996002 12
_ STAAD SPACE -- PAGE NO. 2
39. 97 4.22267 1.04997 12; 98 -0.483143 0.639592 12; 99 0.861688 0.757638 12
40. 100 2.7365 0.921164 12; 101 0 0.225 12; 102 3.60001 0.450001 12
41. 103 0 0.560001 12; 104 3.60001 0.750002 12; 105 -0.423373 0.644838 12
42. 106 0.726209 0.745746 12; 107 1.89963 0.848636 12; 108 3.04534 0.947931 12
43. 109 4.17286 1.04565 12; 110 0 0 15; 111 1.8 0 15; 112 3.60001 0 15
44. 113 0 0.682001 15; 114 1.8 0.840002 15; 115 3.60001 0.996002 15
45. 116 4.22267 1.04997 15; 117 -0.483143 0.639592 15; 118 0.861688 0.757638 15
46. 119 2.7365 0.921164 15; 120 0 0.225 15; 121 3.60001 0.450001 15
47. 122 0 0.560001 15; 123 3.60001 0.750002 15; 124 -0.423373 0.644838 15
48. 125 0.726209 0.745746 15; 126 1.89963 0.848636 15; 127 3.04534 0.947931 15
49. 128 4.17286 1.04565 15; 129 -0.423373 0.644838 -0.900002
50. 130 0.726209 0.745746 -0.900002; 131 1.89963 0.848636 -0.900002
51. 132 3.04534 0.947931 -0.900002; 133 4.17286 1.04565 -0.900002
52. 134 -0.423373 0.644838 15.9; 135 0.726209 0.745746 15.9
53. 136 1.89963 0.848636 15.9; 137 3.04534 0.947931 15.9; 138 4.17286 1.04565
15.9
54. MEMBER INCIDENCES
55. 1 1 11; 2 2 5; 3 3 12; 4 4 30; 5 5 31; 6 6 33; 7 8 29; 8 9 5; 9 10 32
56. 10 11 26; 11 12 28; 12 11 9; 13 12 10; 28 26 4; 31 28 6; 32 29 4; 33 30 9
57. 34 31 10; 35 32 6; 36 33 7; 37 34 44; 38 35 38; 39 36 45; 40 37 49; 41 38 50
58. 42 39 52; 43 41 48; 44 42 38; 45 43 51; 46 44 46; 47 45 47; 48 44 42; 49 45 43
59. 50 46 37; 51 47 39; 52 48 37; 53 49 42; 54 50 43; 55 51 39; 56 52 40; 57 53 63
60. 58 54 57; 59 55 64; 60 56 68; 61 57 69; 62 58 71; 63 60 67; 64 61 57; 65 62 70
61. 66 63 65; 67 64 66; 68 63 61; 69 64 62; 70 65 56; 71 66 58; 72 67 56; 73 68 61
62. 74 69 62; 75 70 58; 76 71 59; 77 72 82; 78 73 76; 79 74 83; 80 75 87; 81 76 88
63. 82 77 90; 83 79 86; 84 80 76; 85 81 89; 86 82 84; 87 83 85; 88 82 80; 89 83 81
64. 90 84 75; 91 85 77; 92 86 75; 93 87 80; 94 88 81; 95 89 77; 96 90 78
65. 97 91 101; 98 92 95; 99 93 102; 100 94 106; 101 95 107; 102 96 109; 103 98 105
66. 104 99 95; 105 100 108; 106 101 103; 107 102 104; 108 101 99; 109 102 100
67. 110 103 94; 111 104 96; 112 105 94; 113 106 99; 114 107 100; 115 108 96
68. 116 109 97; 117 110 120; 118 111 114; 119 112 121; 120 113 125; 121 114 126
69. 122 115 128; 123 117 124; 124 118 114; 125 119 127; 126 120 122; 127 121 123
70. 128 120 118; 129 121 119; 130 122 113; 131 123 115; 132 124 113; 133 125 118
71. 134 126 119; 135 127 115; 136 128 116; 137 129 29; 138 29 48; 139 48 67
72. 140 67 86; 141 86 105; 142 105 124; 143 124 134; 144 130 30; 145 30 49
73. 146 49 68; 147 68 87; 148 87 106; 149 106 125; 150 125 135; 151 131 31
74. 152 31 50; 153 50 69; 154 69 88; 155 88 107; 156 107 126; 157 126 136
75. 158 132 32; 159 32 51; 160 51 70; 161 70 89; 162 89 108; 163 108 127
76. 164 127 137; 165 133 33; 166 33 52; 167 52 71; 168 71 90; 169 90 109
77. 170 109 128; 171 128 138
78. DEFINE MATERIAL START
79. ISOTROPIC STEEL
80. E 1.99947E+08
81. POISSON 0.3
82. DENSITY 76.8191
83. ALPHA 6.5E-06
84. DAMP 0.03
85. G 7.7221E+07
86. TYPE STEEL
87. STRENGTH RY 1.5 RT 1.2
88. END DEFINE MATERIAL
89. MEMBER PROPERTY COLDFORMED INDIAN
90. 1 TO 3 10 11 28 31 37 TO 39 46 47 50 51 57 TO 59 66 67 70 71 77 TO 79 86 87 -
91. 90 91 97 TO 99 106 107 110 111 117 TO 119 126 127 130 -
92. 131 TABLE ST 80CS50X2
93. 4 TO 9 32 TO 36 40 TO 45 52 TO 56 60 TO 65 72 TO 76 80 TO 85 92 TO 96 100
-
94. 101 TO 105 112 TO 116 120 TO 125 132 TO 136 TABLE ST 80CS50X2
_ STAAD SPACE -- PAGE NO. 3
95. 12 13 48 49 68 69 88 89 108 109 128 129 TABLE ST 40LU40X3.15
96. 137 TO 171 TABLE ST 60CS60X2
97. CONSTANTS
98. BETA 5 MEMB 137 TO 171
99. MATERIAL STEEL ALL
100. SUPPORTS
101. 1 TO 3 34 TO 36 53 TO 55 72 TO 74 91 TO 93 110 TO 112 PINNED
102. LOAD 1 LOADTYPE DEAD TITLE DL
103. SELFWEIGHT Y -1 LIST ALL
104. MEMBER LOAD
105. 137 TO 143 165 TO 171 UNI GY -0.08
106. 144 TO 164 UNI GY -0.15
107. LOAD 2 LOADTYPE WIND TITLE WL_UP CASE A
108. MEMBER LOAD
109. 151 TO 171 UNI Y 0.8
110. 137 TO 150 UNI Y 0.69
111. LOAD 3 LOADTYPE WIND TITLE WL_UP CASE B
112. MEMBER LOAD
113. 151 TO 171 UNI Y -0.73
114. 137 TO 150 UNI Y -0.69
115. LOAD 4 LOADTYPE WIND TITLE WL_DN CASE A
116. MEMBER LOAD
117. 137 TO 150 UNI Y 0.8
118. 151 TO 171 UNI Y 0.69
119. LOAD 5 LOADTYPE WIND TITLE WL_DN CASE B
120. MEMBER LOAD
121. 137 TO 150 UNI Y -0.73
122. 151 TO 171 UNI Y -0.69
123. LOAD COMB 6 1.4DL
124. 1 1.4
125. LOAD COMB 7 1.2DL+WL_UP CASE A
126. 1 1.2 2 1.0
127. LOAD COMB 8 1.2DL+WL_UP CASE B
128. 1 1.2 3 1.0
129. LOAD COMB 9 1.2DL+WL_DN CASE A
130. 1 1.2 4 1.0
131. LOAD COMB 10 1.2DL+WL_DN CASE B
132. 1 1.2 5 1.0
133. LOAD COMB 11 0.9DL+WL_UP CASE A
134. 1 0.9 2 1.0
135. LOAD COMB 12 0.9DL+WL_UP CASE B
136. 1 0.9 3 1.0
137. LOAD COMB 13 0.9DL+WL_DN CASE A
138. 1 0.9 4 1.0
139. LOAD COMB 14 0.9DL+WL_DN CASE B
140. 1 0.9 5 1.0
141. LOAD COMB 15 DL+WL_UP CASE A
142. 1 1.0 2 1.0
143. LOAD COMB 16 DL+WL_UP CASE B
144. 1 1.0 3 1.0
145. LOAD COMB 17 DL+WL_DN CASE A
146. 1 1.0 4 1.0
147. LOAD COMB 18 DL+WL_DN CASE B
148. 1 1.0 5 1.0
149. LOAD COMB 19 DL+0.6WL_UP CASE A
150. 1 1.0 2 0.6
_ STAAD SPACE -- PAGE NO. 4
151. LOAD COMB 20 DL+0.6WL_UP CASE B
152. 1 1.0 3 0.6
153. LOAD COMB 21 DL+0.6WL_DN CASE A
154. 1 1.0 4 0.6
155. LOAD COMB 22 DL+0.6WL_DN CASE B
156. 1 1.0 5 0.6
157. PERFORM ANALYSIS
_
PROBLEM STATISTICS
-----------------------------------
NUMBER OF JOINTS 124 NUMBER OF MEMBERS 155
NUMBER OF PLATES 0 NUMBER OF SOLIDS 0
NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 18
Using 64-bit analysis engine.
SOLVER USED IS THE IN-CORE ADVANCED MATH SOLVER
TOTAL PRIMARY LOAD CASES = 5, TOTAL DEGREES OF FREEDOM =
690
TOTAL LOAD COMBINATION CASES = 17 SO FAR.
_
158. PARAMETER 1
159. CODE AISI 2016
160. FYLD 355000 ALL
161. FU 450000 ALL
162. RATIO 1 ALL
163. KY 1 MEMB 1 TO 3 10 11 28 31 37 TO 39 46 47 50 51 57 TO 59 66 67 70 71 77
-
164. 78 TO 79 86 87 90 91 97 TO 99 106 107 110 111 117 TO 119 126 127 130 131
165. KZ 1 MEMB 1 TO 3 10 11 28 31 37 TO 39 46 47 50 51 57 TO 59 66 67 70 71 77
-
166. 78 TO 79 86 87 90 91 97 TO 99 106 107 110 111 117 TO 119 126 127 130 131
167. LY 0.682001 MEMB 1 10 28 37 46 50 57 66 70 77 86 90 97 106 110 117 126 130
168. LY 0.840002 MEMB 2 38 58 78 98 118
169. LY 0.996002 MEMB 3 11 31 39 47 51 59 67 71 79 87 91 99 107 111 119 127 131
170. LZ 0.682001 MEMB 1 10 28 37 46 50 57 66 70 77 86 90 97 106 110 117 126 130
171. LZ 0.840002 MEMB 2 38 58 78 98 118
172. LZ 0.996002 MEMB 3 11 31 39 47 51 59 67 71 79 87 91 99 107 111 119 127 131
173. KY 1 MEMB 4 TO 9 32 TO 36 40 TO 45 52 TO 56 60 TO 65 72 TO 76 80 TO 85
92 -
174. 93 TO 96 100 TO 105 112 TO 116 120 TO 125 132 TO 136
175. KZ 1 MEMB 4 TO 9 32 TO 36 40 TO 45 52 TO 56 60 TO 65 72 TO 76 80 TO 85
92 -
176. 93 TO 96 100 TO 105 112 TO 116 120 TO 125 132 TO 136
177. LY 4.72368 MEMB 4 TO 9 32 TO 36 40 TO 45 52 TO 56 60 TO 65 72 TO 76 -
178. 80 TO 85 92 TO 96 100 TO 105 112 TO 116 120 TO 125 132 TO 136
179. LZ 4.72368 MEMB 4 TO 9 32 TO 36 40 TO 45 52 TO 56 60 TO 65 72 TO 76 -
180. 80 TO 85 92 TO 96 100 TO 105 112 TO 116 120 TO 125 132 TO 136
181. CHECK CODE ALL
_STEEL DESIGN
Appendix F Staad Output
STAAD SPACE -- PAGE NO. 5
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 1_ SECTION:ST 80CS50X2 LEN: 0.225 LOC: 0.225 |
| STATUS: PASS RATIO: 0.041 REF: Eq. H1.1-1 LC: 9 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 2_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.091 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 3_ SECTION:ST 80CS50X2 LEN: 0.450 LOC: 0.450 |
| STATUS: PASS RATIO: 0.116 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 4_ SECTION:ST 80CS50X2 LEN: 0.729 LOC: 0.000 |
| STATUS: PASS RATIO: 0.182 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 5_ SECTION:ST 80CS50X2 LEN: 0.100 LOC: 0.100 |
| STATUS: PASS RATIO: 0.073 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 6
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 6_ SECTION:ST 80CS50X2 LEN: 0.575 LOC: 0.000 |
| STATUS: PASS RATIO: 0.357 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 7_ SECTION:ST 80CS50X2 LEN: 0.060 LOC: 0.060 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 8_ SECTION:ST 80CS50X2 LEN: 0.942 LOC: 0.942 |
| STATUS: PASS RATIO: 0.115 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 9_ SECTION:ST 80CS50X2 LEN: 0.310 LOC: 0.000 |
| STATUS: PASS RATIO: 0.216 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 10_ SECTION:ST 80CS50X2 LEN: 0.335 LOC: 0.335 |
| STATUS: PASS RATIO: 0.114 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 7
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 11_ SECTION:ST 80CS50X2 LEN: 0.300 LOC: 0.000 |
| STATUS: PASS RATIO: 0.104 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 12_ SECTION:ST 40LU40X3.15 LEN: 1.013 LOC: 1.013 |
| STATUS: PASS RATIO: 0.191 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 13_ SECTION:ST 40LU40X3.15 LEN: 0.984 LOC: 0.984 |
| STATUS: PASS RATIO: 0.142 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 28_ SECTION:ST 80CS50X2 LEN: 0.122 LOC: 0.122 |
| STATUS: PASS RATIO: 0.144 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 31_ SECTION:ST 80CS50X2 LEN: 0.246 LOC: 0.246 |
| STATUS: PASS RATIO: 0.212 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 8
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 32_ SECTION:ST 80CS50X2 LEN: 0.425 LOC: 0.425 |
| STATUS: PASS RATIO: 0.267 REF: Sec. H2 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 33_ SECTION:ST 80CS50X2 LEN: 0.136 LOC: 0.000 |
| STATUS: PASS RATIO: 0.148 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 34_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.064 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 35_ SECTION:ST 80CS50X2 LEN: 0.557 LOC: 0.557 |
| STATUS: PASS RATIO: 0.335 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 36_ SECTION:ST 80CS50X2 LEN: 0.050 LOC: 0.000 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 9
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 37_ SECTION:ST 80CS50X2 LEN: 0.225 LOC: 0.225 |
| STATUS: PASS RATIO: 0.055 REF: Eq. H1.1-1 LC: 9 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 38_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.125 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 39_ SECTION:ST 80CS50X2 LEN: 0.450 LOC: 0.450 |
| STATUS: PASS RATIO: 0.161 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 40_ SECTION:ST 80CS50X2 LEN: 0.729 LOC: 0.000 |
| STATUS: PASS RATIO: 0.257 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 41_ SECTION:ST 80CS50X2 LEN: 0.100 LOC: 0.100 |
| STATUS: PASS RATIO: 0.103 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 10
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 42_ SECTION:ST 80CS50X2 LEN: 0.575 LOC: 0.000 |
| STATUS: PASS RATIO: 0.500 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 43_ SECTION:ST 80CS50X2 LEN: 0.060 LOC: 0.060 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 44_ SECTION:ST 80CS50X2 LEN: 0.942 LOC: 0.942 |
| STATUS: PASS RATIO: 0.161 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 45_ SECTION:ST 80CS50X2 LEN: 0.310 LOC: 0.000 |
| STATUS: PASS RATIO: 0.299 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 46_ SECTION:ST 80CS50X2 LEN: 0.335 LOC: 0.335 |
| STATUS: PASS RATIO: 0.160 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 11
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 47_ SECTION:ST 80CS50X2 LEN: 0.300 LOC: 0.000 |
| STATUS: PASS RATIO: 0.145 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 48_ SECTION:ST 40LU40X3.15 LEN: 1.013 LOC: 1.013 |
| STATUS: PASS RATIO: 0.263 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 49_ SECTION:ST 40LU40X3.15 LEN: 0.984 LOC: 0.984 |
| STATUS: PASS RATIO: 0.193 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 50_ SECTION:ST 80CS50X2 LEN: 0.122 LOC: 0.122 |
| STATUS: PASS RATIO: 0.202 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 51_ SECTION:ST 80CS50X2 LEN: 0.246 LOC: 0.246 |
| STATUS: PASS RATIO: 0.296 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 12
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 52_ SECTION:ST 80CS50X2 LEN: 0.425 LOC: 0.425 |
| STATUS: PASS RATIO: 0.376 REF: Sec. H2 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 53_ SECTION:ST 80CS50X2 LEN: 0.136 LOC: 0.000 |
| STATUS: PASS RATIO: 0.210 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 54_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.089 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 55_ SECTION:ST 80CS50X2 LEN: 0.557 LOC: 0.557 |
| STATUS: PASS RATIO: 0.469 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 56_ SECTION:ST 80CS50X2 LEN: 0.050 LOC: 0.000 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 13
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 57_ SECTION:ST 80CS50X2 LEN: 0.225 LOC: 0.225 |
| STATUS: PASS RATIO: 0.053 REF: Eq. H1.1-1 LC: 9 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 58_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.117 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 59_ SECTION:ST 80CS50X2 LEN: 0.450 LOC: 0.450 |
| STATUS: PASS RATIO: 0.150 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 60_ SECTION:ST 80CS50X2 LEN: 0.729 LOC: 0.000 |
| STATUS: PASS RATIO: 0.239 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 61_ SECTION:ST 80CS50X2 LEN: 0.100 LOC: 0.100 |
| STATUS: PASS RATIO: 0.096 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 14
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 62_ SECTION:ST 80CS50X2 LEN: 0.575 LOC: 0.000 |
| STATUS: PASS RATIO: 0.469 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 63_ SECTION:ST 80CS50X2 LEN: 0.060 LOC: 0.060 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 64_ SECTION:ST 80CS50X2 LEN: 0.942 LOC: 0.942 |
| STATUS: PASS RATIO: 0.150 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 65_ SECTION:ST 80CS50X2 LEN: 0.310 LOC: 0.000 |
| STATUS: PASS RATIO: 0.282 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 66_ SECTION:ST 80CS50X2 LEN: 0.335 LOC: 0.335 |
| STATUS: PASS RATIO: 0.149 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 15
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 67_ SECTION:ST 80CS50X2 LEN: 0.300 LOC: 0.000 |
| STATUS: PASS RATIO: 0.135 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 68_ SECTION:ST 40LU40X3.15 LEN: 1.013 LOC: 1.013 |
| STATUS: PASS RATIO: 0.245 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 69_ SECTION:ST 40LU40X3.15 LEN: 0.984 LOC: 0.984 |
| STATUS: PASS RATIO: 0.182 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 70_ SECTION:ST 80CS50X2 LEN: 0.122 LOC: 0.122 |
| STATUS: PASS RATIO: 0.188 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 71_ SECTION:ST 80CS50X2 LEN: 0.246 LOC: 0.246 |
| STATUS: PASS RATIO: 0.277 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 16
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 72_ SECTION:ST 80CS50X2 LEN: 0.425 LOC: 0.425 |
| STATUS: PASS RATIO: 0.351 REF: Sec. H2 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 73_ SECTION:ST 80CS50X2 LEN: 0.136 LOC: 0.000 |
| STATUS: PASS RATIO: 0.194 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 74_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.083 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 75_ SECTION:ST 80CS50X2 LEN: 0.557 LOC: 0.557 |
| STATUS: PASS RATIO: 0.439 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 76_ SECTION:ST 80CS50X2 LEN: 0.050 LOC: 0.000 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 17
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 77_ SECTION:ST 80CS50X2 LEN: 0.225 LOC: 0.225 |
| STATUS: PASS RATIO: 0.053 REF: Eq. H1.1-1 LC: 9 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 78_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.117 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 79_ SECTION:ST 80CS50X2 LEN: 0.450 LOC: 0.450 |
| STATUS: PASS RATIO: 0.150 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 80_ SECTION:ST 80CS50X2 LEN: 0.729 LOC: 0.000 |
| STATUS: PASS RATIO: 0.239 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 81_ SECTION:ST 80CS50X2 LEN: 0.100 LOC: 0.100 |
| STATUS: PASS RATIO: 0.096 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 18
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 82_ SECTION:ST 80CS50X2 LEN: 0.575 LOC: 0.000 |
| STATUS: PASS RATIO: 0.469 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 83_ SECTION:ST 80CS50X2 LEN: 0.060 LOC: 0.060 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 84_ SECTION:ST 80CS50X2 LEN: 0.942 LOC: 0.942 |
| STATUS: PASS RATIO: 0.150 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 85_ SECTION:ST 80CS50X2 LEN: 0.310 LOC: 0.000 |
| STATUS: PASS RATIO: 0.282 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 86_ SECTION:ST 80CS50X2 LEN: 0.335 LOC: 0.335 |
| STATUS: PASS RATIO: 0.149 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 19
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 87_ SECTION:ST 80CS50X2 LEN: 0.300 LOC: 0.000 |
| STATUS: PASS RATIO: 0.135 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 88_ SECTION:ST 40LU40X3.15 LEN: 1.013 LOC: 1.013 |
| STATUS: PASS RATIO: 0.245 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 89_ SECTION:ST 40LU40X3.15 LEN: 0.984 LOC: 0.984 |
| STATUS: PASS RATIO: 0.182 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 90_ SECTION:ST 80CS50X2 LEN: 0.122 LOC: 0.122 |
| STATUS: PASS RATIO: 0.188 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 91_ SECTION:ST 80CS50X2 LEN: 0.246 LOC: 0.246 |
| STATUS: PASS RATIO: 0.277 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 20
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 92_ SECTION:ST 80CS50X2 LEN: 0.425 LOC: 0.425 |
| STATUS: PASS RATIO: 0.351 REF: Sec. H2 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 93_ SECTION:ST 80CS50X2 LEN: 0.136 LOC: 0.000 |
| STATUS: PASS RATIO: 0.194 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 94_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.083 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 95_ SECTION:ST 80CS50X2 LEN: 0.557 LOC: 0.557 |
| STATUS: PASS RATIO: 0.439 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 96_ SECTION:ST 80CS50X2 LEN: 0.050 LOC: 0.000 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 21
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 97_ SECTION:ST 80CS50X2 LEN: 0.225 LOC: 0.225 |
| STATUS: PASS RATIO: 0.055 REF: Eq. H1.1-1 LC: 9 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 98_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.125 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 99_ SECTION:ST 80CS50X2 LEN: 0.450 LOC: 0.450 |
| STATUS: PASS RATIO: 0.161 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 100_ SECTION:ST 80CS50X2 LEN: 0.729 LOC: 0.000 |
| STATUS: PASS RATIO: 0.257 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 101_ SECTION:ST 80CS50X2 LEN: 0.100 LOC: 0.100 |
| STATUS: PASS RATIO: 0.103 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 22
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 102_ SECTION:ST 80CS50X2 LEN: 0.575 LOC: 0.000 |
| STATUS: PASS RATIO: 0.500 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 103_ SECTION:ST 80CS50X2 LEN: 0.060 LOC: 0.060 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 104_ SECTION:ST 80CS50X2 LEN: 0.942 LOC: 0.942 |
| STATUS: PASS RATIO: 0.161 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 105_ SECTION:ST 80CS50X2 LEN: 0.310 LOC: 0.000 |
| STATUS: PASS RATIO: 0.299 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 106_ SECTION:ST 80CS50X2 LEN: 0.335 LOC: 0.335 |
| STATUS: PASS RATIO: 0.160 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 23
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 107_ SECTION:ST 80CS50X2 LEN: 0.300 LOC: 0.000 |
| STATUS: PASS RATIO: 0.145 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 108_ SECTION:ST 40LU40X3.15 LEN: 1.013 LOC: 1.013 |
| STATUS: PASS RATIO: 0.263 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 109_ SECTION:ST 40LU40X3.15 LEN: 0.984 LOC: 0.984 |
| STATUS: PASS RATIO: 0.193 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 110_ SECTION:ST 80CS50X2 LEN: 0.122 LOC: 0.122 |
| STATUS: PASS RATIO: 0.202 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 111_ SECTION:ST 80CS50X2 LEN: 0.246 LOC: 0.246 |
| STATUS: PASS RATIO: 0.296 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 24
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 112_ SECTION:ST 80CS50X2 LEN: 0.425 LOC: 0.425 |
| STATUS: PASS RATIO: 0.376 REF: Sec. H2 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 113_ SECTION:ST 80CS50X2 LEN: 0.136 LOC: 0.000 |
| STATUS: PASS RATIO: 0.210 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 114_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.089 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 115_ SECTION:ST 80CS50X2 LEN: 0.557 LOC: 0.557 |
| STATUS: PASS RATIO: 0.469 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 116_ SECTION:ST 80CS50X2 LEN: 0.050 LOC: 0.000 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 25
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 117_ SECTION:ST 80CS50X2 LEN: 0.225 LOC: 0.225 |
| STATUS: PASS RATIO: 0.041 REF: Eq. H1.1-1 LC: 9 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 118_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.091 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 119_ SECTION:ST 80CS50X2 LEN: 0.450 LOC: 0.450 |
| STATUS: PASS RATIO: 0.116 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 120_ SECTION:ST 80CS50X2 LEN: 0.729 LOC: 0.000 |
| STATUS: PASS RATIO: 0.182 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 121_ SECTION:ST 80CS50X2 LEN: 0.100 LOC: 0.100 |
| STATUS: PASS RATIO: 0.073 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 26
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 122_ SECTION:ST 80CS50X2 LEN: 0.575 LOC: 0.000 |
| STATUS: PASS RATIO: 0.357 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 123_ SECTION:ST 80CS50X2 LEN: 0.060 LOC: 0.060 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 124_ SECTION:ST 80CS50X2 LEN: 0.942 LOC: 0.942 |
| STATUS: PASS RATIO: 0.115 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 125_ SECTION:ST 80CS50X2 LEN: 0.310 LOC: 0.000 |
| STATUS: PASS RATIO: 0.216 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 126_ SECTION:ST 80CS50X2 LEN: 0.335 LOC: 0.335 |
| STATUS: PASS RATIO: 0.114 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 27
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 127_ SECTION:ST 80CS50X2 LEN: 0.300 LOC: 0.000 |
| STATUS: PASS RATIO: 0.104 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 128_ SECTION:ST 40LU40X3.15 LEN: 1.013 LOC: 1.013 |
| STATUS: PASS RATIO: 0.191 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 129_ SECTION:ST 40LU40X3.15 LEN: 0.984 LOC: 0.984 |
| STATUS: PASS RATIO: 0.142 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 130_ SECTION:ST 80CS50X2 LEN: 0.122 LOC: 0.122 |
| STATUS: PASS RATIO: 0.144 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 131_ SECTION:ST 80CS50X2 LEN: 0.246 LOC: 0.246 |
| STATUS: PASS RATIO: 0.212 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 28
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 132_ SECTION:ST 80CS50X2 LEN: 0.425 LOC: 0.425 |
| STATUS: PASS RATIO: 0.267 REF: Sec. H2 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 133_ SECTION:ST 80CS50X2 LEN: 0.136 LOC: 0.000 |
| STATUS: PASS RATIO: 0.148 REF: Eq. H1.2-1 LC: 4 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 134_ SECTION:ST 80CS50X2 LEN: 0.840 LOC: 0.840 |
| STATUS: PASS RATIO: 0.064 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 135_ SECTION:ST 80CS50X2 LEN: 0.557 LOC: 0.557 |
| STATUS: PASS RATIO: 0.335 REF: Eq. H1.2-1 LC: 2 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 136_ SECTION:ST 80CS50X2 LEN: 0.050 LOC: 0.000 |
| STATUS: PASS RATIO: 0.000 REF: Sec. H2 LC: 6 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 29
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 137_ SECTION:ST 60CS60X2 LEN: 0.900 LOC: 0.900 |
| STATUS: PASS RATIO: 0.149 REF: Sec. H2 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 138_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.344 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 139_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.317 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 140_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.287 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 141_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.317 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 30
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 142_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.344 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 143_ SECTION:ST 60CS60X2 LEN: 0.900 LOC: 0.000 |
| STATUS: PASS RATIO: 0.149 REF: Sec. H2 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 144_ SECTION:ST 60CS60X2 LEN: 0.900 LOC: 0.900 |
| STATUS: PASS RATIO: 0.163 REF: Sec. H2 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 145_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.381 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 146_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.350 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 31
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 147_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.318 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 148_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.350 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 149_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.381 REF: Eq. H1.2-1 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 150_ SECTION:ST 60CS60X2 LEN: 0.900 LOC: 0.000 |
| STATUS: PASS RATIO: 0.163 REF: Sec. H2 LC: 10 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 151_ SECTION:ST 60CS60X2 LEN: 0.900 LOC: 0.900 |
| STATUS: PASS RATIO: 0.163 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 32
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 152_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.381 REF: Eq. H1.1-2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 153_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.351 REF: Eq. H1.1-2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 154_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.317 REF: Eq. H1.1-2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 155_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.351 REF: Eq. H1.1-2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 156_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.381 REF: Eq. H1.1-2 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 33
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 157_ SECTION:ST 60CS60X2 LEN: 0.900 LOC: 0.000 |
| STATUS: PASS RATIO: 0.163 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 158_ SECTION:ST 60CS60X2 LEN: 0.900 LOC: 0.900 |
| STATUS: PASS RATIO: 0.163 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 159_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.382 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 160_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.352 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 161_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.318 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 34
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 162_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.352 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 163_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.382 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 164_ SECTION:ST 60CS60X2 LEN: 0.900 LOC: 0.000 |
| STATUS: PASS RATIO: 0.163 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 165_ SECTION:ST 60CS60X2 LEN: 0.900 LOC: 0.900 |
| STATUS: PASS RATIO: 0.149 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 166_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.342 REF: Eq. H1.1-2 LC: 8 |
|-----------------------------------------------------------------------------|
_ STAAD SPACE -- PAGE NO. 35
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 167_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.314 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 168_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.287 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 169_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 3.000 |
| STATUS: PASS RATIO: 0.314 REF: Eq. H1.2-1 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 170_ SECTION:ST 60CS60X2 LEN: 3.000 LOC: 0.000 |
| STATUS: PASS RATIO: 0.342 REF: Eq. H1.1-2 LC: 8 |
|-----------------------------------------------------------------------------|
STAAD.Pro CODE CHECKING - (AISI S100-16) [LRFD] (v1.0)
********************************************************
ALL UNITS ARE IN "M " AND "KN " (U.N.O.)
|-----------------------------------------------------------------------------|
| _MEMBER: 171_ SECTION:ST 60CS60X2 LEN: 0.900 LOC: 0.000 |
| STATUS: PASS RATIO: 0.149 REF: Sec. H2 LC: 8 |
|-----------------------------------------------------------------------------|
182. PARAMETER 2
183. CODE AISI 2016
184. STEEL TAKE OFF LIST ALL
_ STAAD SPACE -- PAGE NO. 36
_STEEL TAKE OFF _
_
STEEL TAKE-OFF
--------------
PROFILE LENGTH(METE) WEIGHT(KN )
_
ST 80CS50X2 43.45 1.288
ST 40LU40X3.15 11.98 0.213
ST 60CS60X2 84.00 2.491
----------------
TOTAL = 3.992
************ END OF DATA FROM INTERNAL STORAGE ************
185. FINISH
*********** END OF THE STAAD.Pro RUN ***********
**** DATE= NOV 9,2024 TIME= 7:36:55 ****
Appendix G Utilization Ratio Appendix H GA Drawing
Actua
Bea Claus L/
Design l Allowabl
m Analysis Normalized Ratio e C
Ratio e Ratio
(Actual/Allowabl
e)
Eq.
1 80CS50X2 80CS50X2 0.041 1.000 0.041 9
H1.1-1
Eq.
2 80CS50X2 80CS50X2 0.091 1.000 0.091 10
H1.2-1
Eq.
3 80CS50X2 80CS50X2 0.116 1.000 0.116 8
H1.2-1
Eq.
4 80CS50X2 80CS50X2 0.182 1.000 0.182 4
H1.2-1
Sec.
5 80CS50X2 80CS50X2 0.073 1.000 0.073 8
H2
Sec.
6 80CS50X2 80CS50X2 0.357 1.000 0.357 8
H2
Sec.
7 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
8 80CS50X2 80CS50X2 0.115 1.000 0.115 10
H1.2-1
Eq.
9 80CS50X2 80CS50X2 0.216 1.000 0.216 2
H1.2-1
Eq.
10 80CS50X2 80CS50X2 0.114 1.000 0.114 10
H1.2-1
Eq.
11 80CS50X2 80CS50X2 0.104 1.000 0.104 8
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
12 0.191 1.000 0.191 10
5 5 H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
13 0.142 1.000 0.142 8
5 5 H1.2-1
Eq.
28 80CS50X2 80CS50X2 0.144 1.000 0.144 10
H1.2-1
Eq.
31 80CS50X2 80CS50X2 0.212 1.000 0.212 8
H1.2-1
Sec.
32 80CS50X2 80CS50X2 0.267 1.000 0.267 10
H2
Eq.
33 80CS50X2 80CS50X2 0.148 1.000 0.148 4
H1.2-1
Eq.
34 80CS50X2 80CS50X2 0.064 1.000 0.064 10
H1.2-1
Eq.
35 80CS50X2 80CS50X2 0.335 1.000 0.335 2
H1.2-1
Sec.
36 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
37 80CS50X2 80CS50X2 0.055 1.000 0.055 9
H1.1-1
Eq.
38 80CS50X2 80CS50X2 0.125 1.000 0.125 10
H1.2-1
Eq.
39 80CS50X2 80CS50X2 0.161 1.000 0.161 8
H1.2-1
Eq.
40 80CS50X2 80CS50X2 0.257 1.000 0.257 4
H1.2-1
Sec.
41 80CS50X2 80CS50X2 0.103 1.000 0.103 8
H2
Sec.
42 80CS50X2 80CS50X2 0.500 1.000 0.500 8
H2
Sec.
43 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
44 80CS50X2 80CS50X2 0.161 1.000 0.161 10
H1.2-1
Eq.
45 80CS50X2 80CS50X2 0.299 1.000 0.299 2
H1.2-1
Eq.
46 80CS50X2 80CS50X2 0.160 1.000 0.160 10
H1.2-1
Eq.
47 80CS50X2 80CS50X2 0.145 1.000 0.145 8
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
48 0.263 1.000 0.263 10
5 5 H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
49 0.193 1.000 0.193 8
5 5 H1.2-1
Eq.
50 80CS50X2 80CS50X2 0.202 1.000 0.202 10
H1.2-1
Eq.
51 80CS50X2 80CS50X2 0.296 1.000 0.296 8
H1.2-1
Sec.
52 80CS50X2 80CS50X2 0.376 1.000 0.376 10
H2
Eq.
53 80CS50X2 80CS50X2 0.210 1.000 0.210 4
H1.2-1
Eq.
54 80CS50X2 80CS50X2 0.089 1.000 0.089 10
H1.2-1
Eq.
55 80CS50X2 80CS50X2 0.469 1.000 0.469 2
H1.2-1
Sec.
56 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
57 80CS50X2 80CS50X2 0.053 1.000 0.053 9
H1.1-1
Eq.
58 80CS50X2 80CS50X2 0.117 1.000 0.117 10
H1.2-1
Eq.
59 80CS50X2 80CS50X2 0.150 1.000 0.150 8
H1.2-1
Eq.
60 80CS50X2 80CS50X2 0.239 1.000 0.239 4
H1.2-1
Sec.
61 80CS50X2 80CS50X2 0.096 1.000 0.096 8
H2
Sec.
62 80CS50X2 80CS50X2 0.469 1.000 0.469 8
H2
Sec.
63 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
64 80CS50X2 80CS50X2 0.150 1.000 0.150 10
H1.2-1
Eq.
65 80CS50X2 80CS50X2 0.282 1.000 0.282 2
H1.2-1
Eq.
66 80CS50X2 80CS50X2 0.149 1.000 0.149 10
H1.2-1
Eq.
67 80CS50X2 80CS50X2 0.135 1.000 0.135 8
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
68 0.245 1.000 0.245 10
5 5 H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
69 0.182 1.000 0.182 8
5 5 H1.2-1
Eq.
70 80CS50X2 80CS50X2 0.188 1.000 0.188 10
H1.2-1
Eq.
71 80CS50X2 80CS50X2 0.277 1.000 0.277 8
H1.2-1
Sec.
72 80CS50X2 80CS50X2 0.351 1.000 0.351 10
H2
Eq.
73 80CS50X2 80CS50X2 0.194 1.000 0.194 4
H1.2-1
Eq.
74 80CS50X2 80CS50X2 0.083 1.000 0.083 10
H1.2-1
Eq.
75 80CS50X2 80CS50X2 0.439 1.000 0.439 2
H1.2-1
Sec.
76 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
77 80CS50X2 80CS50X2 0.053 1.000 0.053 9
H1.1-1
Eq.
78 80CS50X2 80CS50X2 0.117 1.000 0.117 10
H1.2-1
Eq.
79 80CS50X2 80CS50X2 0.150 1.000 0.150 8
H1.2-1
Eq.
80 80CS50X2 80CS50X2 0.239 1.000 0.239 4
H1.2-1
Sec.
81 80CS50X2 80CS50X2 0.096 1.000 0.096 8
H2
Sec.
82 80CS50X2 80CS50X2 0.469 1.000 0.469 8
H2
Sec.
83 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
84 80CS50X2 80CS50X2 0.150 1.000 0.150 10
H1.2-1
Eq.
85 80CS50X2 80CS50X2 0.282 1.000 0.282 2
H1.2-1
Eq.
86 80CS50X2 80CS50X2 0.149 1.000 0.149 10
H1.2-1
Eq.
87 80CS50X2 80CS50X2 0.135 1.000 0.135 8
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
88 0.245 1.000 0.245 10
5 5 H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
89 0.182 1.000 0.182 8
5 5 H1.2-1
Eq.
90 80CS50X2 80CS50X2 0.188 1.000 0.188 10
H1.2-1
Eq.
91 80CS50X2 80CS50X2 0.277 1.000 0.277 8
H1.2-1
Sec.
92 80CS50X2 80CS50X2 0.351 1.000 0.351 10
H2
Eq.
93 80CS50X2 80CS50X2 0.194 1.000 0.194 4
H1.2-1
Eq.
94 80CS50X2 80CS50X2 0.083 1.000 0.083 10
H1.2-1
Eq.
95 80CS50X2 80CS50X2 0.439 1.000 0.439 2
H1.2-1
Sec.
96 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
97 80CS50X2 80CS50X2 0.055 1.000 0.055 9
H1.1-1
Eq.
98 80CS50X2 80CS50X2 0.125 1.000 0.125 10
H1.2-1
Eq.
99 80CS50X2 80CS50X2 0.161 1.000 0.161 8
H1.2-1
Eq.
100 80CS50X2 80CS50X2 0.257 1.000 0.257 4
H1.2-1
Sec.
101 80CS50X2 80CS50X2 0.103 1.000 0.103 8
H2
Sec.
102 80CS50X2 80CS50X2 0.500 1.000 0.500 8
H2
Sec.
103 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
104 80CS50X2 80CS50X2 0.161 1.000 0.161 10
H1.2-1
Eq.
105 80CS50X2 80CS50X2 0.299 1.000 0.299 2
H1.2-1
Eq.
106 80CS50X2 80CS50X2 0.160 1.000 0.160 10
H1.2-1
Eq.
107 80CS50X2 80CS50X2 0.145 1.000 0.145 8
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
108 0.263 1.000 0.263 10
5 5 H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
109 0.193 1.000 0.193 8
5 5 H1.2-1
Eq.
110 80CS50X2 80CS50X2 0.202 1.000 0.202 10
H1.2-1
Eq.
111 80CS50X2 80CS50X2 0.296 1.000 0.296 8
H1.2-1
Sec.
112 80CS50X2 80CS50X2 0.376 1.000 0.376 10
H2
Eq.
113 80CS50X2 80CS50X2 0.210 1.000 0.210 4
H1.2-1
Eq.
114 80CS50X2 80CS50X2 0.089 1.000 0.089 10
H1.2-1
Eq.
115 80CS50X2 80CS50X2 0.469 1.000 0.469 2
H1.2-1
Sec.
116 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
117 80CS50X2 80CS50X2 0.041 1.000 0.041 9
H1.1-1
Eq.
118 80CS50X2 80CS50X2 0.091 1.000 0.091 10
H1.2-1
Eq.
119 80CS50X2 80CS50X2 0.116 1.000 0.116 8
H1.2-1
Eq.
120 80CS50X2 80CS50X2 0.182 1.000 0.182 4
H1.2-1
Sec.
121 80CS50X2 80CS50X2 0.073 1.000 0.073 8
H2
Sec.
122 80CS50X2 80CS50X2 0.357 1.000 0.357 8
H2
Sec.
123 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Eq.
124 80CS50X2 80CS50X2 0.115 1.000 0.115 10
H1.2-1
Eq.
125 80CS50X2 80CS50X2 0.216 1.000 0.216 2
H1.2-1
Eq.
126 80CS50X2 80CS50X2 0.114 1.000 0.114 10
H1.2-1
Eq.
127 80CS50X2 80CS50X2 0.104 1.000 0.104 8
H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
128 0.191 1.000 0.191 10
5 5 H1.2-1
40LU40X3.1 40LU40X3.1 Eq.
129 0.142 1.000 0.142 8
5 5 H1.2-1
Eq.
130 80CS50X2 80CS50X2 0.144 1.000 0.144 10
H1.2-1
Eq.
131 80CS50X2 80CS50X2 0.212 1.000 0.212 8
H1.2-1
Sec.
132 80CS50X2 80CS50X2 0.267 1.000 0.267 10
H2
Eq.
133 80CS50X2 80CS50X2 0.148 1.000 0.148 4
H1.2-1
Eq.
134 80CS50X2 80CS50X2 0.064 1.000 0.064 10
H1.2-1
Eq.
135 80CS50X2 80CS50X2 0.335 1.000 0.335 2
H1.2-1
Sec.
136 80CS50X2 80CS50X2 0.000 1.000 0.000 6
H2
Sec.
137 60CS60X2 60CS60X2 0.149 1.000 0.149 10
H2
Eq.
138 60CS60X2 60CS60X2 0.344 1.000 0.344 10
H1.2-1
Eq.
139 60CS60X2 60CS60X2 0.317 1.000 0.317 10
H1.2-1
Eq.
140 60CS60X2 60CS60X2 0.287 1.000 0.287 10
H1.2-1
Eq.
141 60CS60X2 60CS60X2 0.317 1.000 0.317 10
H1.2-1
Eq.
142 60CS60X2 60CS60X2 0.344 1.000 0.344 10
H1.2-1
Sec.
143 60CS60X2 60CS60X2 0.149 1.000 0.149 10
H2
Sec.
144 60CS60X2 60CS60X2 0.163 1.000 0.163 10
H2
Eq.
145 60CS60X2 60CS60X2 0.381 1.000 0.381 10
H1.2-1
Eq.
146 60CS60X2 60CS60X2 0.350 1.000 0.350 10
H1.2-1
Eq.
147 60CS60X2 60CS60X2 0.318 1.000 0.318 10
H1.2-1
Eq.
148 60CS60X2 60CS60X2 0.350 1.000 0.350 10
H1.2-1
Eq.
149 60CS60X2 60CS60X2 0.381 1.000 0.381 10
H1.2-1
Sec.
150 60CS60X2 60CS60X2 0.163 1.000 0.163 10
H2
Sec.
151 60CS60X2 60CS60X2 0.163 1.000 0.163 8
H2
Eq.
152 60CS60X2 60CS60X2 0.381 1.000 0.381 8
H1.1-2
Eq.
153 60CS60X2 60CS60X2 0.351 1.000 0.351 8
H1.1-2
Eq.
154 60CS60X2 60CS60X2 0.317 1.000 0.317 8
H1.1-2
Eq.
155 60CS60X2 60CS60X2 0.351 1.000 0.351 8
H1.1-2
Eq.
156 60CS60X2 60CS60X2 0.381 1.000 0.381 8
H1.1-2
Sec.
157 60CS60X2 60CS60X2 0.163 1.000 0.163 8
H2
Sec.
158 60CS60X2 60CS60X2 0.163 1.000 0.163 8
H2
Eq.
159 60CS60X2 60CS60X2 0.382 1.000 0.382 8
H1.2-1
Eq.
160 60CS60X2 60CS60X2 0.352 1.000 0.352 8
H1.2-1
Eq.
161 60CS60X2 60CS60X2 0.318 1.000 0.318 8
H1.2-1
Eq.
162 60CS60X2 60CS60X2 0.352 1.000 0.352 8
H1.2-1
Eq.
163 60CS60X2 60CS60X2 0.382 1.000 0.382 8
H1.2-1
Sec.
164 60CS60X2 60CS60X2 0.163 1.000 0.163 8
H2
Sec.
165 60CS60X2 60CS60X2 0.149 1.000 0.149 8
H2
Eq.
166 60CS60X2 60CS60X2 0.342 1.000 0.342 8
H1.1-2
Eq.
167 60CS60X2 60CS60X2 0.314 1.000 0.314 8
H1.2-1
Eq.
168 60CS60X2 60CS60X2 0.287 1.000 0.287 8
H1.2-1
Eq.
169 60CS60X2 60CS60X2 0.314 1.000 0.314 8
H1.2-1
Eq.
170 60CS60X2 60CS60X2 0.342 1.000 0.342 8
H1.1-2
Sec.
171 60CS60X2 60CS60X2 0.149 1.000 0.149 8
H2
Appendix G Utilization Ratio Appendix H GA Drawing
NOTES:-
Location
4H7 Latitude
Longtitude
Total System Capacity
Module Capacity
Total No of Module
:XXXXXXXX
:XXXXXXXX
:897.7KWP
:635
:1414
PV Array Tilt Angle :5°
Mounting Type :Rooftop
3000.0 3000.0 3000.0 3000.0 3000.0
Solar Panel
4735 2382x1134x30
1134
104
996
840 5
5
682
104
1800 1800 00 SA
By
09/11/24 Issued for Quotation
Description
Rev Date
Manufacturer Details:
AL Babtain Metalogalva Solar
Dammam, 3rd Industrial CIty
Kingdom of Saudi Arabia
Project Name: Solar Carport Project at concrete roof - Zamil
Name Date Drawing Title:
Drawn SA PV Layout and structure drawings -
Checked SA Zamil(4H7)
Approved PR
Drawing No. Rev No. Sheet No.
You might also like
- 780Q Gearbox Assembly and Lubrication Drawing100% (3)780Q Gearbox Assembly and Lubrication Drawing2 pages
- Poultry Farm - Structural Drawing (RCC & Steel) and Structural Calculat...0% (1)Poultry Farm - Structural Drawing (RCC & Steel) and Structural Calculat...4 pages
- Aditya Academy Secondary: Physics ProjectNo ratings yetAditya Academy Secondary: Physics Project10 pages
- Uog-Iot Construction Technology and Management Bsc. Program - Year Iii100% (1)Uog-Iot Construction Technology and Management Bsc. Program - Year Iii120 pages
- CRUZ Catalogue: PC Products Roof Racks & AccessoriesNo ratings yetCRUZ Catalogue: PC Products Roof Racks & Accessories82 pages
- DBR of 2PX8 Table 30D 0.5 NGL Ground Mount MMSNo ratings yetDBR of 2PX8 Table 30D 0.5 NGL Ground Mount MMS8 pages
- Seasonal Structure With Manual Tilting Single Pole Dual PanelNo ratings yetSeasonal Structure With Manual Tilting Single Pole Dual Panel7 pages
- EG0222032301 Solar Carport Mounting System-Area A ASCE 7-10) - 10x21No ratings yetEG0222032301 Solar Carport Mounting System-Area A ASCE 7-10) - 10x2120 pages
- 2V28 - 25deg - Biposte Structure - Design ReportNo ratings yet2V28 - 25deg - Biposte Structure - Design Report36 pages
- Statistical Texture Measures Computed From Gray Level Coocurrence MatricesNo ratings yetStatistical Texture Measures Computed From Gray Level Coocurrence Matrices14 pages
- Structure Design Report 5H8@1000 - PurlinNo ratings yetStructure Design Report 5H8@1000 - Purlin64 pages
- Structure Design Calculation of Rooftop Solar Project100% (1)Structure Design Calculation of Rooftop Solar Project13 pages
- Lesson 7 - Simple Machines (Kinds and Safety Use)100% (1)Lesson 7 - Simple Machines (Kinds and Safety Use)22 pages
- Structure Design Report 3H8@1000 - PurlinNo ratings yetStructure Design Report 3H8@1000 - Purlin51 pages
- Circular Footing Design Based On ACI 318-19: Input Data & Design Summary100% (1)Circular Footing Design Based On ACI 318-19: Input Data & Design Summary4 pages
- R01 Structure Drawing of 3H8 Table ConfigurationNo ratings yetR01 Structure Drawing of 3H8 Table Configuration1 page
- RWD62U Programmable Controller Installation and Commissioning GuideNo ratings yetRWD62U Programmable Controller Installation and Commissioning Guide10 pages
- R01 Structure Drawing of 4H7 Table ConfigurationNo ratings yetR01 Structure Drawing of 4H7 Table Configuration1 page
- In The Name of Allah, The Most Beneficent, The Most Merciful0% (1)In The Name of Allah, The Most Beneficent, The Most Merciful66 pages
- S. No. Signal Data Type 1 2 3 4 5 6 7 8 9No ratings yetS. No. Signal Data Type 1 2 3 4 5 6 7 8 91 page
- AAR-001-ISOLATED FDN - IS 456 - Node 1 - 2No ratings yetAAR-001-ISOLATED FDN - IS 456 - Node 1 - 242 pages
- David Moser Creating A Cost-Based Failure Modes and Effects Analysis FMEA For PVNo ratings yetDavid Moser Creating A Cost-Based Failure Modes and Effects Analysis FMEA For PV29 pages
- Rolling Mill Extension Stability Check: Structural Information Input DataNo ratings yetRolling Mill Extension Stability Check: Structural Information Input Data3 pages
- Cannonball-Geotech Report-Final - 10-04-2022No ratings yetCannonball-Geotech Report-Final - 10-04-202264 pages
- OSHA 1910.137 - Electrical Protective EquipmentNo ratings yetOSHA 1910.137 - Electrical Protective Equipment10 pages
- Condition Monitoring of Rotating Electrical Machines 3No ratings yetCondition Monitoring of Rotating Electrical Machines 324 pages
- Structural Steel Design: DR - Mu'taz K.M Ass. Prof. in Civil EngineeringNo ratings yetStructural Steel Design: DR - Mu'taz K.M Ass. Prof. in Civil Engineering12 pages
- Ulrike Jahn Mitigating The Technical Risks in Project LifetimeNo ratings yetUlrike Jahn Mitigating The Technical Risks in Project Lifetime16 pages
- ANTAI Calculation 40m Per Second ASCE 7-10No ratings yetANTAI Calculation 40m Per Second ASCE 7-1013 pages
- R01 Structure Drawing of 5H8 Table ConfigurationNo ratings yetR01 Structure Drawing of 5H8 Table Configuration1 page
- LG Washing Machine Spare Parts Price ListNo ratings yetLG Washing Machine Spare Parts Price List4 pages
- General Structural Notes General Structural Notes: Pe Stamp100% (1)General Structural Notes General Structural Notes: Pe Stamp3 pages
- Design For Module Mounting Structure-Bhadla (8,28) - R5No ratings yetDesign For Module Mounting Structure-Bhadla (8,28) - R58 pages
- Detailed Comments Double carport-MEA - 20.04.24No ratings yetDetailed Comments Double carport-MEA - 20.04.2410 pages
- Understanding Firozabad Glass Industry and GAIL Role100% (1)Understanding Firozabad Glass Industry and GAIL Role13 pages
- SWLD SKYP1 57.5MW TL E DWG LTCR 01 - ApprovedNo ratings yetSWLD SKYP1 57.5MW TL E DWG LTCR 01 - Approved1 page
- 2004 Bombardier DS650 Repair Manual (001 121)No ratings yet2004 Bombardier DS650 Repair Manual (001 121)121 pages
- Double-Design Calculation Report For MMS Structure-RUW Carport 40m-sNo ratings yetDouble-Design Calculation Report For MMS Structure-RUW Carport 40m-s168 pages
- 1.1 General Details & Load Calculations - Substation Building (Pess)No ratings yet1.1 General Details & Load Calculations - Substation Building (Pess)2 pages
- Date DRN by DSGD by CHKD by Apprd by ScaleNo ratings yetDate DRN by DSGD by CHKD by Apprd by Scale1 page
- Pepsico - Detail Design Package - Rev.00No ratings yetPepsico - Detail Design Package - Rev.0043 pages
- WF Base Plate Design Based On AISC-ASD 9th Edition: Input Data & Design SummaryNo ratings yetWF Base Plate Design Based On AISC-ASD 9th Edition: Input Data & Design Summary2 pages
- B269-475-C-Cal-0056-Design Calculation of Sludge Sump Shed-I - Peb StructureNo ratings yetB269-475-C-Cal-0056-Design Calculation of Sludge Sump Shed-I - Peb Structure78 pages
- Interim Geotech Report For Umer Hospital Sanda Raj Garh LahoreNo ratings yetInterim Geotech Report For Umer Hospital Sanda Raj Garh Lahore9 pages
- 2X4 (SEASONAL TILT) STRUCTURE ASSEMBLY LAUOUT, BOQ & DesignNo ratings yet2X4 (SEASONAL TILT) STRUCTURE ASSEMBLY LAUOUT, BOQ & Design3 pages
- 26 Design of Singly Reinforced Continous RCC Beam As Per Is456-2000 23052014No ratings yet26 Design of Singly Reinforced Continous RCC Beam As Per Is456-2000 230520141 page
- Design Report - UPGRADATION MODERNIZATION OF INFRASTRUCTURE AT BIKANERNo ratings yetDesign Report - UPGRADATION MODERNIZATION OF INFRASTRUCTURE AT BIKANER40 pages
- BOXER BJ KICKER KJ Setup Operators Manual ENGNo ratings yetBOXER BJ KICKER KJ Setup Operators Manual ENG4 pages
- MMS Structure Wind Pressure Calculation1No ratings yetMMS Structure Wind Pressure Calculation13 pages
